Professional Documents
Culture Documents
TCN en Menual 170905 He PDF
TCN en Menual 170905 He PDF
Specification Dimensions
(unit: mm)
Series TCN4S TCN4M TCN4H TCN4L
DUAL INDICATOR TEMPERATURE CONTROLLER Power
supply
AC Power
AC/DC Power
100-240VACᜠ 50/60Hz
24VACᜠ 50/60Hz, 24-48VDCᜡ
TCN4S Series TCN4S- -P TCN4M Series
TCN4 SERIES Allowable voltage range 90 to 110% of rated voltage 48 6 64.5 48 6 56 11.5
72 6 64.5
1.7
Power AC Power Max. 5VA(100-240VAC 50/60Hz)
consumption AC/DC Power Max. 5V(24VAC 50/60Hz), Max. 3W(24-48VDC)
INSTRUCTION MANUAL Display method 7 segment (PV: red, SV: green), other display part(green, red) LED method
44.8
45
Character PV(W×H) 7.0×15.0mm 9.5×20.0mm 7.0×14.6mm 11.0×22.0mm
67.5
size SV(W×H) 5.0×9.5mm 7.5×15.0mm 6.0×12.0mm 7.0×14.0mm
Input RTD DIN Pt100Ω, Cu50Ω (Allowable line resistance max.5Ω per a wire)
type TC K(CA), J(IC), L(IC), T(CC), R(PR), S(PR)
Display RTD At room temperature(23ºC ± 5ºC): (PV ± 0.5% or ±1ºC, select the higher one) ± 1 digit
accuracy Out of room temperature range: (PV± 0.5% or ±2ºC, select the higher one)± 1digit TCN4H Series TCN4L Series
1 TC For TCN4S- -P, add ±1℃ by accuracy standard.
48 6 64.5 96 6 64.5
Control Relay 250VACᜠ 3A 1a
output SSR 12VDCᜡ±2V 20mA Max.
Alarm output AL1, AL2 Relay: 250VACᜠ 1A 1a
Control method ON/OFF control, P, PI, PD, PID control
Hysteresis 1 to 100℃/℉ (0.1 to 50.0℃/℉)
Proportional band(P) 0.1 to 999.9ºC/℉
91.5
91.5
96
Integral time(I) 0 to 9999 sec.
Terminal cover(sold separately)
Derivative time(D) 0 to 9999 sec.
RSA-COVER(48×48mm) RMA-COVER(72×72mm)
Control period(T) 0.5 to 120.0 sec. 70 3
48.4
Manual reset 0.0 to 100.0%
Thank you for choosing our Autonics product.
Sampling period 100ms
Please read the following safety considerations before use.
41.5
Dielectric AC power 2000VAC 50/60Hz 1min.(between input terminal and power terminal)
68.5
64
strength AC/DC power 1000VAC 50/60Hz 1min.(between input terminal and power terminal)
Vibration 0.75mm amplitude at frequency of 5 to 55Hz in each X, Y, Z direction for 2 hours Panel cut-out
Safety Considerations Mechanical OUT: Over 5,000,000 times, AL1/2: Over 5,000,000 times
A
18
22
Bracket
Relay life
cycle OUT: Over 200,000 times(250VAC 3A resistive load) TCN4S Series TCN4M, TCN4H, TCN4L Series 9.8
※Please observe all safety considerations for safe and proper product operation to avoid hazards.
13
Electrical 31
AL1/2: Over 300,000 times(250VAC 1A resistive load)
D
48.6 22.5
※Safety considerations are categorized as follows. Insulation resistance Min. 100MΩ(at 500VDC megger) 20
5
3.3
Warning Failure to follow these instructions may result in serious injury or death. 45
B
Noise Square-wave noise by noise simulator(pulse width 1㎲) ±2KV R-phase and S-phase C
Caution Failure to follow these instructions may result in personal injury or product damage. Memory retention Approx. 10 years (when using non-volatile semiconductor memory type) RHA-COVER(48×96mm) RLA-COVER(96×96mm )
※The symbols used on the product and instruction manual represent the following Environ Ambient temp. -10 to 50ºC, Storage: -20 to 60ºC
4
46 47.2 4 94 3
44.9
-ment Ambient humi.
36
symbol represents caution due to special circumstances in which hazards may occur.
16
35 to 85%RH, Storage: 35 to 85%RH
Double insulation or reinforced insulation (mark: , dielectric strength between Size
Insulation type
Warning the measuring input part and the power part : AC power 2kV, AC/DC power 1kV) A B C D
37.5
40.5
Series
Approval 15
1. Fail-safe device must be installed when using the unit with machinery that may cause
91.5
91.5
86
86
21 TCN4S Min. 65 Min. 65 45 0.6
45 00.6
serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment, 2 Approx. 147g Approx. 203g Approx. 194g Approx. 275g 55 0
Weight
ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster (approx. 100g) (approx. 133g) (approx. 124g) (approx. 179g) TCN4M Min. 90 Min. 90 68 00.7 68 00.7
12
prevention devices, etc.) 1: At room temperature(23ºC±5ºC) TCN4H Min. 65 Min. 115 45 00.6 92 00.8
Failure to follow this instruction may result in fire, personal injury, or economic loss. - Below 200ºC of thermocouple R(PR), S(PR) is (PV ±0.5% or ±3ºC, select the higher one) ±1 digit 23.9
TCN4L Min. 115 Min. 115 92 00.8 92 00.8
2. Install on a device panel to use. - Over 200ºC of thermocouple R(PR), S(PR) is (PV ±0.5% or ±2ºC, select the higher one) ±1 digit
13
13
Failure to follow this instruction may result in electric shock or fire. - Termocouple L (IC), RTD Cu50Ω is (PV ±0.5% or ±2ºC, select the higher one) ±1 digit
56
3. Do not connect, repair, or inspect the unit while connected to a power source. Out of room temperature range
Failure to follow this instruction may result in electric shock or fire. - Below 200ºC of thermocouple R(PR), S(PR) is (PV ±1.0% or ±6ºC, select the higher one) ±1 digit
4. Check 'Connections' before wiring. - Over 200ºC of thermocouple R(PR), S(PR) is (PV ±0.5% or ±5ºC, select the higher one) ±1 digit
Failure to follow this instruction may result in fire. - Thermocouple L(IC), RTD Cu50Ω is (PV ±0.5% or ±3ºC, select the higher one) ±1 digit Connections Parameter Groups
5. Do not disassemble or modify the unit. For TCN4S- -P, add ±1℃ by accuracy standard. 1)TCN4S Series 3)TCN4M Series
1. All Parameter
Failure to follow this instruction may result in electric shock or fire. 2: The weight includes packaging. The weight in parentheses is for unit only.
AL1 OUT Run mode
Environment resistance is rated at no freezing or condensation. SSR 250VAC
Caution OUT※1 1A 1a
1. When connecting the power input and relay output, use AWG 20(0.50mm2) cable or over and
Unit Description 1. Present temperature (PV) display (Red) AL2 OUT Please any key among 2sec. 4sec.
1) RUN mode: Present temperature (PV) display 250VAC , , ,
tighten the terminal screw with a tightening torque of 0.74~0.90N.m. 1A 1a
When connecting the sensor input and communication cable without dedicated cable, use 2) Parameter setting mode: Parameter display SV setting Parameter 1group Parameter 2group
Relay OUT B'
AWG 28~16 cable and tighten the terminal screw with a tightening torque of 0.74~0.90N.m. 2. Set temperature (SV) display (Green) 250VAC AL1 OUT PAR1 PAR2
Failure to follow this instruction may result in fire or malfunction due to contact failure. 1) RUN mode: Set temperature (SV) display 3A 1a SSR 250VAC
1 2) Parameter setting mode
B OUT※1 1A 1a
2. Use the unit within the rated specifications. Input Temperature Input Input
: Parameter setting value display TC AL1 alarm termerature
Failure to follow this instruction may result in fire or product damage. A AL2 OUT sensor unit correction digital filter
3. Use dry cloth to clean the unit, and do not use water or organic solvent. 8 3. Control/Alarm output display indicator 250VAC AL1 IN-Tㅑㅜ UNIT IN-Bㅑㅜ MAvF
RTD 1A 1a
Failure to follow this instruction may result in electric shock or fire. 3 1) OUT: It turns ON when the control output is ON.
4. Do not use the unit in the place where flammable/explosive/corrosive gas, humidity, direct During SSR drive output type in CYCLE/ Relay OUT B' AL2 alarm termerature
2 SOURCE※2 250VAC
sunlight, radiant heat, vibration, impact, or salinity may be present. PHASE control, this indicator turns ON when 3A 1a AL2 Control output SV high- SV low-limit
Failure to follow this instruction may result in fire or explosion. 4 7 MV is over 3.0%. B + Control type operation limit value value
5. Keep metal chip, dust, and wire residue from flowing into the unit. 2) AL1/AL2: It turns ON when the alarm output is ON. TC Auto tunung
5 C-MD O-FT H-SV L-SV
Failure to follow this instruction may result in fire or product damage. 4. Auto tuning indicator + A
AT
AT indicator flashes by every 1 sec during operating RTD
auto tuning.
Ordering Information 5. key
SOURCE※2 Proportional band Control output
type
SSR drive output
method※1
Control AL1 alarm
6 2)TCN4S- -P 4)TCN4H/L Series P cycle operation mode
T CN 4 S 2 4 R P Used when entering into parameter groups, OUT SSrM T AL-1
returning to RUN mode, moving parameter, and saving AL1 OUT Integral time
setting values. 250VAC
Wiring method No-mark Bolt wiring method 6. Adjustment SSR 1A 1a I
1
Used when entering into set value change mode, digit moving and digit up/down. OUT※1 AL2 OUT LBA detection LBA Alarm output AL2 alarm
P Connector plug connection method monitoring time hysteresis operation mode
250VAC Derivative time band
Control output 7. Digital input key 1A 1a
R Relay contact + SSR drive output 2
Press keys for 3 sec. to operate the set function Relay OUT D LBaㅠㅠB LBaT AHYS AL-2
250VAC
Power supply 2 24VAC 50/60Hz, 24-48VDC (RUN/STOP, alarm output reset, auto tuning) in digital input key [DI-T]. 3A 1a B'
Manual reset
4 100-240VAC 50/60Hz 8. Temperature unit (ºC/℉) indicator B
Sub output
It shows current temperature unit. A
TC REST Digital input Control output MV in case Parameter
2 Alarm1 + Alarm2 output key of input break error lock