Professional Documents
Culture Documents
294782595 جداول التصميم لمواسير الصرف والتهوية والتغذية PDF
294782595 جداول التصميم لمواسير الصرف والتهوية والتغذية PDF
)جدول تحديد قطر ماسورة تصريف مياه المطر الرأسية ( Table # 1
Size of Vertical Conductors and Leaders
Diameter )Horizontally Projected Roof Area (Square feet
of (مساحة السطح بالقدم مربع)
leaders )( Rainfall rate (Inches per hourمعدل تراكم مياه المطر على السطح بالبوصة /ساعة)
(Inches)a 1 2 3 4 5 6 7 8 9 10 11 12
2 2,880 1,440 960 720 575 480 410 360 320 290 260 240
3 8,800 4,400 2,930 2,200 1,760 1,470 1,260 1,100
4 18,400 9,200 6,130 4,600 3,680 3,070 2,630 2,300
5 34,600 17,300 11,530 8,650 6,920 5,765 4,945 4,325
6 54,000 27,000 17,995 13,500 10,800 9,000 7,715 6,750
8 116,000 58,000 38,660 29,000 23,200 19,315 16,570 14,500 12,890 11,600 10,545 9,600
a. Sizes indicated are the diameter of circular piping. This table is applicable of other shapes provided the
cross sectional shape fully encloses a circle of the diameter indicated in this table.
1
Table # 2 ()جدول تحديد قطر ماسورة تصريف مياه المطر األفقية
Size of Horizontal Storm Drainage Piping
Horizontally Projected Roof Area (Square feet)
Size of
)(مساحة السطح بالقدم مربع
Horizontal
Rainfall rate (Inches per hour)
Piping
) ساعة/ (معدل تراكم مياه المطر على السطح بالبوصة
(Inches)
1 2 3 4 5 6
1/8 Unit vertical in 12 units horizontal (1% Slope)
3 3,288 1,644 1,096 822 657 548
4 7,520 3,760 2,506 1,800 1,504 1,253
5 13,360 6,680 4,453 3,340 2,672 2,227
6 21,400 10,700 7,133 5,350 4,280 3,566
8 46,000 23,000 15,330 11,500 9,200 7,600
10 82,800 41,400 27,600 20,700 16,580 13,800
12 133,200 66,600 44,400 33,300 26,650 22,200
15 218,000 109,000 72,800 59,500 47,600 39,650
1/4 Unit vertical in 12 units horizontal (2% Slope)
3 4,640 2,320 1,546 1,160 928 773
4 10,600 5,300 3,533 2,650 2,120 1,766
5 18,880 9,440 6,293 4,720 3,776 3,146
6 30,200 15,100 10,066 7,550 6,040 5,033
8 65,200 32,600 21,733 16,300 13,040 10,866
10 116,800 58,400 38,950 29,200 23,350 19,450
12 188,000 94,000 62,600 47,000 37,600 31,350
15 336,000 168,000 112,000 84,000 67,250 56,000
1/2 Unit vertical in 12 units horizontal (4 % Slope)
3 6,576 3,288 2,295 1,644 1,310 1,096
4 15,040 7,520 5,010 3,760 3,010 2,500
5 26,720 13,360 8,900 6,680 5,320 4,450
6 42,800 21,400 13,700 10,700 8,580 7,140
8 92,000 46,000 30,650 23,000 18,400 15,320
10 171,600 85,800 55,200 41,400 33,150 27,600
12 266,400 133,200 88,800 66,600 53,200 44,400
15 476,000 238,000 158,800 119,000 95,300 79,250
Table # 3 ()جدول تحديد الميل الصحيح لمواسير تصريف مياه المطر األفقية
Slope of Horizontal Rain (Storm) Water Pipe
Pipe Size (Inches) MinimumSlope (Inch per foot)
2 1/2 or less 1/4 (2 %)
3 to 6 1/8 (1 %)
8 or larger 1/16 (0.5 %)
2
Table # 4 ()جدول تحديد قطر المزراب الشبه دائرى
Size of Semicircular Roof Gutters
Horizontally Projected Roof Area (Square feet)
Diameter )(مساحة السطح بالقدم مربع
of Gutters Rainfall rate (Inches per hour)
(Inches) ) ساعة/ (معدل تراكم مياه المطر على السطح بالبوصة
1 2 3 4 5 6
1/16 Unit vertical in 12 units horizontal (0.5 % Slope) %141 ميل
3 680 340 226 170 136 113
4 1,440 720 480 360 288 240
5 2,500 1,250 834 625 500 416
6 3,840 1,920 1,280 960 768 640
7 5,520 2,760 1,840 1,380 1,100 918
8 7,960 3,980 2,655 1,,990 1,590 1,325
10 14,400 7,200 4,800 3,600 2,880 2,400
1/8 Unit vertical in 12 units horizontal (1 % Slope) %1 ميل
3 960 480 320 240 192 160
4 2,040 1,020 681 510 408 340
5 3,520 1,760 1,172 880 704 587
6 5,440 2,720 1,815 1,360 1,085 905
7 7,800 3,900 2,600 1,950 1,560 1,300
8 11,200 5,600 3,740 2,800 2,240 1,870
10 20,400 10,200 6,800 5,100 4,080 3,400
1/4 Unit vertical in 12 units horizontal (2 % Slope) %2 ميل
3 1,360 680 454 340 272 226
4 2,880 1,440 960 720 576 480
5 5,000 2,500 1,668 1,250 1,000 834
6 7,680 3,840 2,560 1,960 1,536 1,280
7 11,040 5,520 3,860 2,760 2,205 1,840
8 15,920 7,960 5,310 3,980 3,180 2,655
10 28,800 14,400 9,600 7,200 5,750 4,800
1/2 Unit vertical in 12 units horizontal (4 % Slope) %0 ميل
3 1,920 960 640 480 384 320
4 4,080 2,040 1,360 1,020 816 680
5 7,080 3,540 2,360 1,770 1,415 1,180
6 11,080 5,540 3,695 2,770 2,220 1,850
7 15,600 7,800 5,200 3,900 3,120 2,600
8 22,400 11,200 7,460 5,600 4,480 3,730
10 40,000 20,000 13,330 10,000 8,000 6,660
3
.2جداول تصميم مواسير الصرف الصحى-:
إختبار النظام :يتم إختبار شبكة (نظام) مواسير الصرف الصحى وذلك بملئ النظام بماء ال يقل إرتفاعه بالمواسير عن 11
قدم ( 8103مم) ولمدة ال تقل عن 11دقيقة ,أو بإستخدام ضغط هواء بمقدار 1رطل /بوصة مربعة ( 8041باسكال)
ولمدة ال تقل عن 11دقيقة.
ال يتم تقليل قطر ماسورة الصرف الصحى فى إتجاه السريان على اإلطالق.
نوع المواسير و األكواع والتيهات المستخدمة :سيتم إستخدام مواسير أو أكواع أو تيهات مصنوعة من البالستيك ضغط 01
أبيض ( )CPVC Sch 40سواء للمواسير التى تحت األرض أو للمواسير التى فوق األرض أو للمواسير المدفونة بالجدران
أو بالخرسانة أو باألرض.
ينبغى عمل طبات تسليك ( )Clean outsكلما لزم األمر (عند تغيير إتجاه الماسورة بزاوية مقدارها 01درجة ,أو على
الخطوط األفقية على مسافات بينية بمقدار 11متر بحد أقصى وتكون طبة التسليك فى هذه الحالة مرتفعة عن األرض بمقدار
1سم ,أو أسفل األعمدة وعلى مسافة 11سم على أقل تقدير من سطح األرض) وذلك بقطر يساوى قطر الماسورة التى
تخدمها طبة التسليك وبحد أقصى 0بوصة ألى طبة تسليك.
يتم تحديد ميل ماسورة تصريف مياه المطر األفقية من جدول رقم .1
لن يتم إستخدام األكواع ذات الـ 01درجة على اإلطالق لتغيير زاوية السريان بمقدار 01درجة ,بل سيتم إستخدام كوع 01
درجة مع كوع آخر له قطر إنحناء كبير ( )Long Sweep Elbowوذلك لتغيير إتجاه السريان بمقدار 01درجة.
لن يتم إستخدام التيهات ذات الـ 01درجة بل سيتم إستخدام تى ( )Teeبزاوية ميل مقدارها 01درجة مع كوع 01درجة
وذلك لتوصيل تفريعة مع خط آخر يميل عليه بزاوية 01درجة.
تُعتبر الماسورة أفقية إذا كانت تميل على المحور األفقى بمقدار 01درجة أو أقل ,بينما تُعتبر الماسورة رأسية إذا كانت تميل
على المحور األفقى بمقدار أكبر من 01درجة.
لألجهزة الصحية الغير ُمدونة بجدول رقم 1يُمكنك اإلستعانة بجدول رقم , 0مع مالحظة أن األجهزة الصحية المذكورة
بجدول رقم 1هى لإلستخدام المتقطع فقط .وإذا صادفك أجهزة صحية ذات إستخدام مستمر أو شبه مستمر فإنه يمكنك إعتبار
أن كل جالون فى الدقيقة الواحدة يساوى عدد 2وحدة صرف .فمثالً إذا كان عندك وحدة مناولة هواء تأخذ هواء بنسبة
%111من الجو الخارجى فيمكنك حساب معدل التكاثف من المعادلة التالية :معدل تكاثف الماء من الوحدة (رطل ماء فى
الساعة الواحدة) = 0401معدل سريان الهواء (قدم مكعب فى الدقيقة) فرق الرطوبة النسبية بين الظروف الجوية
خارج المبنى وداخله (رطل ماء متكاثف لكل رطل هواء جاف).
أى جهاز صحى غير ُمدون بجدول رقم 1فإن أقل قطر ماسورة مسموح بتوصيلها عليه (أقل قطر للمصيدة) هو قطر الجهاز
نفسه أو 82( "1421مم) أيهما أكبر.
يمكنك إستخدام جدول رقم 1وجدول رقم ( 0هذان الجدولين للصرف المباشر " )"Direct Wasteفى تحديد عدد وحدات
الصرف ( )dfuلألجهزة الصحية التى لها تصريف غير مباشر " "Indirect Wasteمع خطوط الصرف الصحى.
)جدول تقدير عدد وحدات الصرف لألجهزة الصحية المختلفة وللمجموعات( Table # 1
Drainage Fixture Units for Fixtures & Groups
Drainage Minimum
Fixture Unit Size of Trap
(dfu) Value as أقل قطر ماسورة (
Fixture Type Load Factors يتم توصيله
)نوع الجهاز الصحى( قيمة وحدات ( بالجهاز الصحى أو
الصرف للجهاز )المجموعة
الصحى أو
)للمجموعة
Automatic clothes washers, commerciala,g
3 2
غسالة مالبس أتوماتيكية لإلستخدام التجارى
Automatic clothes washers, residentialg
2 2
غسالة مالبس أتوماتيكية لإلستخدام المنزلى
Bathroom group " water closet + lavatory + bathtub or shower,
including or excluding a bidet, an emergancy floor drain or both " (1.6
gpf water closet)f 5 -----
مجموعة أجهزة صحية بحمام (عبارة عن مرحاض "له معدل كسح 141جالون فى
المرة الواحدة أو أقل" +مغسلة +بانيو أو دش ويشمل ذلك أو ال يشمل بيديه أو
ّ
4
)صفاية أرضى للطوارئ أو كليهما
Bathroom group " water closet + lavatory + bathtub or shower,
including or excluding a bidet, an emergancy floor drain or both "
(Water closet flushing greater than 1.6 gpf)f
6 -----
141 مجموعة أجهزة صحية بحمام (عبارة عن مرحاض "له معدل كسح أكبر من
بانيو أو دش ويشمل ذلك أو ال يشمل بيديه+ مغسلة+ "المرة الواحدة ّ جالون فى
)أو صفاية أرضى للطوارئ أو كليهما
Bathtubb (With or without overhead shower or whirpool
2 1 1/2
attachments) )بانيو (مع دش رأسى أو بدونه
Bidet بيديه 1 1 1/4
Combination sink and tray 2 1 1/2
Dental lavatory مغسلة لطبيب أسنان 1 1 1/4
Dental unit or cupidor 1 1 1/4
Dishwashing machine,c domestic غسالة أطباق لإلستخدام المنزلى 2 1 1/2
Drinking fountain نافورة شُرب 1/2 1 1/4
Emergency floor drain صفاية أرضى للطوارئ 0 2
Floor drains صفاية أرضى عادية 2 2
Kitchen sink, domestic حوض مطبخ لإلستخدام المنزلى 2 1 1/2
Kitchen sink, domestic with food waste grinder and/or
2 1 1/2
dishwasher
Laundary tray (1 or 2 compartments) 2 1 1/2
Lavatory مغسلة 1 1 1/4
Shower دش 2 1 1/2
Service sink 2 1 1/2
Sink 2 1 1/2
Urinal مبولة 4 Note d
Urinal, 1 gallon per flush (gpf) or less
2e Note d
جالون فى الم ّرة الواحدة أو أقل1 مبولة معدل الكسح لها
Urinal, nonwater supplied مبولة ليس لها مياه تغذية 0.5 Note d
Washsink (Circular or multiple) each set of faucets 2 1 1/2
Water closet, flushometer tank, public or private 4e Note d
Water closet, private (1.6 gpf)
3e Note d
)المرة الواحدة أو أقل
ّ جالون فى141 مرحاض لإلستخدام الخاص (معدل الكسح
Water closet, private (Flushing greater than 1.6 gpf)
4e Note d
)المرة الواحدة
ّ جالون فى141 مرحاض لإلستخدام الخاص (معدل الكسح أكبر من
Water closet, public (1.6 gpf)
4e Note d
)المرة الواحدة أو أقل
ّ جالون فى141 مرحاض لإلستخدام العام (معدل الكسح
Water closet, public (Flushing greater than 1.6 gpf)
6e Note d
)المرة الواحدة
ّ جالون فى141 مرحاض لإلستخدام العام (معدل الكسح أكبر من
Note:-
1. Bathroom group: A group of fixtures consisting of water closet, lavatory, bathtub or shower, including
or excluding a bidet, an emergancy floor drain or both. Such fixtures are located together on the same
floor level
a. For traps larger than 3 inches, use table # 4.
b. A showerhead over a bathtub or whirlpool bathtub attachment does not increase the drainage fixture
unit.
c. For fixtures not listed in this table use table # 4 (By the help of fixture drainage diameter). The
minimum trap size for unlisted fixtures shall be the size of fixture's drainage outlet but not less than
1.25" (32 mm). Drainage fixture units (dfu) values for continous and semicontinous flow into a
drainage system shall be computed on the bases that 1 gpm (0.06 L / S) of flow is equivalent to two
fixture units (i.e. 1 gpm = 2 dfu). The drainage fixture units (dfu) load of an indirect waste receptor
5
receiving the discharge of indirectly connected fixtures shall be the sume of the drainage fixture unit
values of the fixtures that discharge to the receptor , but not less than the drainage fixture unit value
given for the direct wast receptor in table # 1 or table # 4.
d. Trap size shall be consistent with the fixture outlet size.
e. For the purpose of computing loads on building drains and sewers, water closets and urinals shall not
be rated at a lower drainage fixture unit unless the lower values are confirmed by testing.
f. For fixtures added to a dwelling unit bathroom group, add the dfu value of those additional fixtures to
the bathroom group fixture count.
g. For an automatic clothes washer standpipe: The wast pipe from an automatic clothes washer shall
discharge through an air break into a standpipe {Standpipes shall be individually trapped, extend a
minimum of 18 inches (457 mm) and maximum of 42 inches (1,066 mm) above the trap weir. Access
shall be provided to all standpipes and drains for rodding} or into a laundary sink. The trap and
fixture drain for an automatic clothes washer standpipe shall be minimum of 2 inches in diameter. The
automatic clothes washer fixture drain shall connect to a branch drain or drainage stack a minimum of
3 inches in diameter. Automatic clothes washers that discharge by gravity shall be permitted to drain a
waste receptor or an approved trench drain.
Table # 2 ()جدول تحديد قطر ماسورة الصرف الرئيسية للمبنى أو التفريعات الرئيسية خارج المبنى الموصولة بماسورة الصرف الرئيسية للمبنى
Building Drain & Sewers Sizing Table
Table # 3 ()جدول تحديد قطر ماسورة الصرف األفقية الفرعية من أى جهاز صحى أو ماسورة أفقية داخل المبنى أو عمود الصرف
Horizontal Fixture Branches & Stack Sizing Tablea
Maximum number of drainage fixture units (dfu) connected to any fixture branch or
Diameter stack
of pipe ( أقصى عدد من وحدات الصرف موصولة مع ماسورة صرف فرعية أفقية خارجة من جهاز صحى واحد أو عدة
(Inches) )أجهزة صحية داخل المبنى أو موصولة مع عامود صرف لمبنى
قطر Total dfu for Stacksb
الماسورة horizontal branch Total dfu Total dfu for stack Total dfu for stack
بالبوصة (ماسورة صرف فرعية discharge into one of 3 branch greater than 3
خارجة من جهاز صحى واحد branch interval intervals or less branch intervals
6
أو عدّة أجهزة صحية داخل (عامود صرف لمبنى (عامود صرف لمبنى أقل (عامود صرف لمبنى
)المبنى مكون من دور واحد من ثالثة أدوار وأزيد من )أزيد من ثالثة أدوار
)فقط )دور واحد
1½ 3 2 4 8
2 6 6 10 24
2½ 12 9 20 42
3 20 20 48 72
4 160 90 240 500
5 360 200 540 1,100
6 620 350 960 1,900
8 1,400 600 2,200 3,600
10 2,500 1,000 3,800 5,600
12 2,900 1,500 6,000 8,400
15 7,000 Note c Note c Note c
a. Does not include branches of the building drain. Refer to table # 1.
b. Stack shall be sized based on the total accumulated connected load load at each story or branch interval.
As the total accumulated connected load decreases, stacks are permitted to be reduced in size. Stack
diameter shall not be less than 1/2 of the largest stack size required dimeter.
c. Sizing load based on design criteria.
Table # 4 (1 )جدول تحديد عدد وحدات الصرف ألى جهاز صحى معلوم قطر الصرف الخاص به وغير ُمدون بالجدول رقم
Drainage Fixture Units for Fixture Drains or Trap
Fixture Drain or Trap Size (Inches) Drainage Fixture Unit (dfu) Value
()قطر ماسورة الصرف للجهاز الصحى ()عدد وحدات الصرف
1 1/4 1
1 1/2 2
2 3
2 1/2 4
3 5
4 6
Note:
There will be some fixtures which are not listed in table # 1. In this case you cane estimate
their dfu from their drain size and by the help of this table (table # 4).
Table # 6 ()جدول تحديد أقل معدل سريان مقبول لمضخة الصرف الصحى بمعلومية قطر ماسورة الطرد للمضخة
Minimum Capacity of Sewage Pump or Sewage Ejector
Diameter of the Discharge Pipe (inches) Capacity of Pump or Ejector (gpm)
قطر ماسورة الطرد لمضخة الصرف الصحى أقل سعة مسموح بها لمضخة الصرف الصحى
2 21
2 1/2 30
3 46
7
-:)Vent Piping( جداول تصميم مواسير التهوية.8
Table # 1 (" وذلك حسب طول هذا العامودVent Stack" ) جدول تحديد قطر عامود التهوية الرئيسي
Size and Developed Length of Stack Vents and Vent Stacks
Total Maximum Developed Length of Vent (feet)a
Diameter
fixture Diameter of Vent (inches)
of soil or
units
waste
(dfu) 1
stack 1 1/2 2 2 1/2 3 4 5 6 8 10 12
being 1/4
(inches)
vented
1 1/4 2 30 ------ ------ ------ ------ ------ ------ ------ ------ ------ ------
1 1/2 8 50 150 ------ ------ ------ ------ ------ ------ ------ ------ ------
1 1/2 10 30 100 ------ ------ ------ ------ ------ ------ ------ ------ ------
2 12 30 75 200 ------ ------ ------ ------ ------ ------ ------ ------
2 20 26 50 150 ------ ------ ------ ------ ------ ------ ------ ------
2 1/2 42 ------ 30 100 300 ------ ------ ------ ------ ------ ------ ------
3 10 ------ 42 150 360 1,040 ------ ------ ------ ------ ------ ------
3 21 ------ 32 110 270 810 ------ ------ ------ ------ ------ ------
3 53 ------ 27 94 230 680 ------ ------ ------ ------ ------ ------
3 102 ------ 25 86 210 620 ------ ------ ------ ------ ------ ------
4 43 ------ ------ 35 85 250 980 ------ ------ ------ ------ ------
4 140 ------ ------ 27 65 200 750 ------ ------ ------ ------ ------
4 320 ------ ------ 23 55 170 640 ------ ------ ------ ------ ------
4 540 ------ ------ 21 50 150 580 ------ ------ ------ ------ ------
5 190 ------ ------ ------ 28 82 320 990 ------ ------ ------ ------
5 490 ------ ------ ------ 21 63 250 760 ------ ------ ------ ------
5 940 ------ ------ ------ 18 53 210 670 ------ ------ ------ ------
5 1,400 ------ ------ ------ 16 49 190 590 ------ ------ ------ ------
6 500 ------ ------ ------ ------ 33 130 400 1,000 ------ ------ ------
6 1,100 ------ ------ ------ ------ 26 100 310 780 ------ ------ ------
6 2,000 ------ ------ ------ ------ 22 84 260 660 ------ ------ ------
6 2,900 ------ ------ ------ ------ 20 77 240 600 ------ ------ ------
8 1,800 ------ ------ ------ ------ ------ 31 95 240 940 ------ ------
8 3,400 ------ ------ ------ ------ ------ 24 73 190 720 ------ ------
8 5,600 ------ ------ ------ ------ ------ 20 62 160 610 ------ ------
8 7,600 ------ ------ ------ ------ ------ 18 56 140 560 ------ ------
10 4,000 ------ ------ ------ ------ ------ ------ 31 78 310 960 ------
10 7,200 ------ ------ ------ ------ ------ ------ 24 60 240 740 ------
10 11,000 ------ ------ ------ ------ ------ ------ 20 51 200 630 ------
10 15,000 ------ ------ ------ ------ ------ ------ 18 46 180 570 ------
12 7,300 ------ ------ ------ ------ ------ ------ ------ 31 120 380 940
12 13,000 ------ ------ ------ ------ ------ ------ ------ 24 94 300 720
12 20,000 ------ ------ ------ ------ ------ ------ ------ 20 79 250 610
12 26,000 ------ ------ ------ ------ ------ ------ ------ 18 72 230 500
15 15,000 ------ ------ ------ ------ ------ ------ ------ ------ 40 130 310
15 25,000 ------ ------ ------ ------ ------ ------ ------ ------ 31 96 240
15 38,000 ------ ------ ------ ------ ------ ------ ------ ------ 26 81 200
15 50,000 ------ ------ ------ ------ ------ ------ ------ ------ 24 74 180
8
)جدول تحديد الميل الصحيح لمواسير التهوية األفقية( Table #
Slope of Horizontal Vent Pipe
)Pipe Size (Inches MinimumSlope , Inch per foot
2 1/2 or less )1/4 (2 %
3 to 6 )1/8 (1 %
8 or larger )1/16 (0.5 %
لمجموعة من األجهزة الصحية ,أو قطر الـ Relief Ventأو قطر التهوية الفرعية " Table # ("Branch Vent
) جدول تحديد قطر ماسورة التهوية الجماعية ""Circuit Vent Pipe
Permissable number of fixture units
Size of Pipe Number of Fixture Units Allowed
)"32 mm (1 1/4 1
)"38 mm (1 1/2 8
)"50 mm (2 18
)"63 mm (2 1/2 36
)"75 mm (3 72
)"100 mm (4 384
مالحظات-:
.1يُستخدم هذا الجدول فى تحديد قطر مواسير التهوية التالية-:
قطر ماسورة التهوية الجماعية (.)Circuit / Loop Vent Pipe
قطر ماسورة التهوية الفرعية (.)Branch Vent Pipe
قطر ماسورة الـ Relief Vent Pipeلمجموعة من األجهزة الصحية موصولة على التوازى مع بعضها
البعض وتصرف على ماسورة صرف أفقية واحدة.
ال يقل قطر ماسورة الـ Relief Vent Pipeلمجموعة من األجهزة الصحية عن 83مم أو نصف قطر
ماسورة الصرف التى تخدمها أو مما حصلت عليه من الجدول السابق أيهم أكبر.
يجب أال تزيد عدد األجهزة الصحية التى تخدمها ماسورة التهوية الجماعية الواحدة عن عدد , 3وإذا زادت
عدد األجهزة الصحية التى يُراد عمل تهوية جماعية لها عن 3فإنه يجب فى هذه الحالة إستخدام أكثر من
ماسورة تهوية جماعية.
):-جدول تحديد قطر ماسورة التهوية الجماعية لمجموعة من المراحيض( Table #
)( Size of Circuit Vent for Battery of Water Closets
Number of Water Closets Diameter of Circuit Vent
Installed in Series قطر ماسورة التهوية الجماعية
عدد المراحيض ال ُمراد عمل تهوية
mm inch
جماعية لهم
2 50 2
3:6 75 3
7 or more 100 4
9
-: جداول التصميم لمواسير التغذية.0
Table # 1 ()جدول تحديد عدد وحدات التغذية لألجهزة الصحية المختلفة
Load Values Assigned to Fixturesa
Type of Load Values, in Water Supply Fixture
Fixture Occupancy
Supply Units (wsfu)
نوع طريقة
Control عدد وحدات التغذية
الجهاز الصحى اإلستخدام
Cold Hot Total
Bathroom Private خاص Flush tank
group (water خزان كسح
closet + lavatory 2.7 1.5 3.6
+ bathtub or
shower,
including or Private خاص Flush valve
excluding a
bidet, an
صمام طرد
6 3 8
emergancy floor
drain or both)
Private خاص Faucet
1 1 1.4
Bathtub حنفية أو محبس
بانيوPublic Faucet
3 3 4
حنفية أو محبس
Bidet Private خاص Faucet
1.5 1.5 2
بيديه حنفية أو محبس
Combination Private خاص Faucet
2.25 2.25 3
fixture حنفية أو محبس
Dishwashing Private خاص Automatic
machine ------ 1.4 1.4
غسالة أطباق
Drinking Offices, etc 3/8" valve
fountain Hotel, محبس أو حنفية 0.25 ------ 0.25
restaurant بوصة3/8 بقطر
Private خاص Faucet
1 1 1.4
حنفية أو محبس
Kitchen sink
Hotel, Faucet
3 3 4
restaurant حنفية أو محبس
Laundary Private خاص Faucet
1 1 1.4
trays (1 to 3) حنفية أو محبس
Private خاص Faucet
0.5 0.5 0.7
حنفية أو محبس
Lavatory
Public عام Faucet
1.5 1.5 2
حنفية أو محبس
Service sink Offices, etc Faucet
2.25 2.25 3
حنفية أو محبس
Public عام Mixing valve
3 3 4
خالط
Shower head
Private خاص Mixing valve
1 1 1.4
خالط
Public عام 1" flush valve
10 ------ 10
Urinal ِمبولة "1 صمام طرد
Public عام 3/4" flush valve 5 ------ 5
11
"0/8 صمام طرد
Public عام Flush tank 3 ------ 3
صندوق طرد أو كسح
Washing Private خاص Automatic 1 1 1.4
machine, 8 Public عام Automatic
2.25 2.25 3
Lb (3.63 kg)
Washing Public عام Automatic
machine, 15 3 3 4
Lb (6.8 kg)
Private خاص Flush valve 6 ------ 6
صمام طرد أو كسح
Private خاص Flush tank
2.2 ------ 2.2
صندوق طرد أو كسح
Water closet Public عام Flush valve 10 ------ 10
مرحاض صمام طرد أو كسح
Public عام Flush tank
5 ------ 5
صندوق طرد أو كسح
Public or Flushometer
2 ------ 2
privet tank
a. For fixtures not listed, loads should be assumed by comparing the fixture to one listed using water in
similar quantities and at similar rates. The assigned loads for fixtures with both hot and cold water
supplies are given for separate hot and cold water loads and for total load. The separate hot and cold
water loads beeing three-fourth of the total load for the fixture in each case.
Table # 2 ()جدول تحديد معدل سريان مياه التغذية بمعلومية عدد وحدات التغذية
Table for Estimating Demand
Supply Systems Predominantly for Flush Supply Systems Predominantly for Flush
Tank Valve
Load Demand Load Demand
Water Supply Water Supply
gpm ft3 / minute gpm ft3 / minute
Fixture Unit Fixture Unit
1 3 ------ ------ ------
2 5 ------ ------ ------
3 6.5 ------ ------ ------
4 8 ------ ------ ------
5 9.4 5 15
6 10.7 6 17.4
7 11.8 7 19.8
8 12.8 8 22.2
9 13.7 9 24.6
10 14.6 10 27
11 15.4 11 27.8
12 16 12 28.6
13 16.5 13 29.4
14 17 14 30.2
15 17.5 15 31
16 18 16 31.8
17 18.4 17 32.6
18 18.8 18 33.4
19 19.2 19 34.2
11
20 19.6 20 35
25 21.5 25 38
30 23.3 30 42
35 24.9 35 44
40 26.3 40 46
45 27.7 45 48
50 29.1 50 50
60 32 60 54
70 35 70 58
80 38 80 61.2
90 41 90 64.3
100 43.5 100 67.5
120 48 120 73
140 52.5 140 77
160 57 160 81
180 61 180 85.5
200 65 200 90
225 70 225 95.5
250 75 250 101
275 80 275 104.5
300 85 300 108
400 105 400 127
500 124 500 143
750 170 750 177
1,000 208 1,000 208
1,250 239 1,250 239
1,500 269 1,500 269
1,750 297 1,750 297
2,000 325 2,000 325
2,500 380 2,500 380
3,000 433 3,000 433
4,000 535 4,000 525
5,000 593 5,000 593
Note:
1. One gallon = 0.1336806 ft3 (i.e 1 gpm = 0.1336806 ft3 / minute)
2. One gallon 3.785 liter.
3. One ft = 0.3048 m = 12 inch
12
Table # (3)
Minimum Required Air Gap
Fixture Minimum Air Gap
a
Away from a Wall (inches) Close to a Wall (inches)
Lavatories and other fixtures
with effective opening not
1 1 1/2
greater than 1/2 inch in
diameter
Sink, laundary trays,
gooseneck back faucets and
other fixtures with effective 1 1/2 2 1/2
opening not greater than 3/4
inch in diameter
Over rim bath filters and
other fixtures with effective
2 3
opening not greater than 1
inch in diameter
Drinking water fountains,
single orifice not greater than
7/16 inches in diameter or
multiple orifices with a total 1 1 1/2
area of 0.15 square inch (area
of circle 7/16 inch in
diameter)
Effective opening greater Two times the diameter of the Three times the diameter of
than 1 inch effective opening the effective opening
Table # (4)
Size of Pipe Identification
Pipe Diameter (inches) Length Background Color Size of Letters (inches)
Field (inches)
3/4 to 1 1/4 8 0.5
1 1/2 to 2 8 0.75
2 1/2 to 6 12 1.25
8 to 10 24 2.5
Over 10 32 3.5
Table # (5)
Size of Drain Pipes for Water Supply Tanks
Tank Capacity (gpm) Drain Pipe (inches)
Up to 750 1
751 – 1,500 1 1/2
1,501 – 3,000 2
3,001 – 5,000 2 1/2
5,000 – 7,500 3
Over 7,500 4
13
Table # (6)
Size of Overflow Pipes for Water Supply Tanks
Maximum Capacityof Water Supply Line to Diameter of Overflow Pipe (inches)
Tank (gpm)
0 – 50 2
50 – 150 2 1/2
150 – 200 3
200 – 400 4
400 – 700 5
700 – 1,000 6
Over 1,000 8
14