Professional Documents
Culture Documents
Ansys Icem CFD User Manual
Ansys Icem CFD User Manual
© 2012 SAS IP, Inc. All rights reserved. Unauthorized use, distribution or duplication is prohibited.
ANSYS, ANSYS Workbench, Ansoft, AUTODYN, EKM, Engineering Knowledge Manager, CFX, FLUENT, HFSS and any
and all ANSYS, Inc. brand, product, service and feature names, logos and slogans are registered trademarks or
trademarks of ANSYS, Inc. or its subsidiaries in the United States or other countries. ICEM CFD is a trademark used
by ANSYS, Inc. under license. CFX is a trademark of Sony Corporation in Japan. All other brand, product, service
and feature names or trademarks are the property of their respective owners.
Disclaimer Notice
THIS ANSYS SOFTWARE PRODUCT AND PROGRAM DOCUMENTATION INCLUDE TRADE SECRETS AND ARE CONFID-
ENTIAL AND PROPRIETARY PRODUCTS OF ANSYS, INC., ITS SUBSIDIARIES, OR LICENSORS. The software products
and documentation are furnished by ANSYS, Inc., its subsidiaries, or affiliates under a software license agreement
that contains provisions concerning non-disclosure, copying, length and nature of use, compliance with exporting
laws, warranties, disclaimers, limitations of liability, and remedies, and other provisions. The software products
and documentation may be used, disclosed, transferred, or copied only in accordance with the terms and conditions
of that software license agreement.
For U.S. Government users, except as specifically granted by the ANSYS, Inc. software license agreement, the use,
duplication, or disclosure by the United States Government is subject to restrictions stated in the ANSYS, Inc.
software license agreement and FAR 12.212 (for non-DOD licenses).
Third-Party Software
See the legal information in the product help files for the complete Legal Notice for ANSYS proprietary software
and third-party software. If you are unable to access the Legal Notice, please contact ANSYS, Inc.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. iii
User Manual
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
iv formation of ANSYS, Inc. and its subsidiaries and affiliates.
User Manual
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. v
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
vi formation of ANSYS, Inc. and its subsidiaries and affiliates.
Introduction to ANSYS ICEM CFD
ANSYS ICEM CFD provides advanced geometry acquisition, mesh generation, and mesh optimization
tools to meet the requirement for integrated mesh generation for today’s sophisticated analyses.
Maintaining a close relationship with the geometry during mesh generation, ANSYS ICEM CFD is used
especially in engineering applications such as computational fluid dynamics and structural analysis.
ANSYS ICEM CFD’s mesh generation tools offer the capability to parametrically create meshes from
geometry in numerous formats:
• Multiblock structured
• Unstructured hexahedral
• Unstructured tetrahedral
ANSYS ICEM CFD provides a direct link between geometry and analysis. In ANSYS ICEM CFD, geometry
can be input from just about any format, whether from a commercial CAD design package, 3rd party
universal database, scan data or point data. Beginning with a robust geometry module which supports
the creation and modification of surfaces, curves and points, ANSYS ICEM CFD’s open geometry database
offers the flexibility to combine geometric information in various formats for mesh generation. The
resulting structured or unstructured meshes, topology, inter-domain connectivity and boundary conditions
are then stored in a database where they can easily be translated to input files formatted for a particular
solver.
Overall Process
The ANSYS ICEM CFD GUI
Overall Process
The generic working process involves the following:
1. Open/Create a project.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 1
Introduction to ANSYS ICEM CFD
Opening/Creating a Project
All the files required for a particular analysis are contained within a Project. You can either open an
existing project or create a new project. The Project directory typically contains one or more of the
following file types:
Tetin (*.tin)
contains geometry entities, material points, part association, and global and entity mesh sizes.
Domain (*.uns)
contains the unstructured mesh.
Blocking (*.blk)
contains the blocking topology.
Attributes (*.atr)
contains attributes, local parameters, and element types.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
2 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Overall Process
Parameters (*.par)
contains model parameters and element types.
Journal (*.jrf)
contains a record of operations performed (echo file).
Replay (*.rpl)
contains the replay script.
The ANSYS ICEM CFD environment can combine CAD surface geometry and triangulated surface data
into a single geometry database (tetin file) using the geometry interfaces. All geometry entities, including
surfaces, curves and points are tagged or associated to a grouping called a part. With this part association,
you can enable or disable all entities within the parts, visualize them with a different color, assign mesh
sizes on all entities within the part and apply different boundary conditions by part.
Although most of the meshing modules within ANSYS ICEM CFD allow minor gaps and holes in the
geometry, in some cases it is necessary to find and close large gaps and holes without returning to the
original CAD software. ANSYS ICEM CFD provides tools for such operations on either CAD or triangulated
surfaces. Finally, curves and points can be automatically created to capture certain key features in the
geometry. These curves and points will act as constraints for the mesher, forcing nodes and edges of
the elements to lie along them, and thus capturing the feature.
Tetra
The ANSYS ICEM CFD Tetra mesher takes full advantage of object-oriented unstructured meshing
technology. With no tedious up-front triangular surface meshing required to provide well-balanced
initial meshes, ANSYS ICEM CFD Tetra works directly from the CAD surfaces and fills the volume
with tetrahedral elements using the Octree approach. A powerful smoothing algorithm provides
the element quality. Options are available to automatically refine and coarsen the mesh both on
geometry and within the volume. A Delaunay algorithm is also included to create tetras from an
existing surface mesh and also to give a smoother transition in the volume element size.
Hexa
The ANSYS ICEM CFD Hexa mesher is a semi-automated meshing module which allows rapid gen-
eration of multi-block structured or unstructured hexahedral volume meshes. ICEM CFD Hexa rep-
resents a new approach to grid generation where the operations most often performed by experts
are automated and made available at the touch of a button. Blocks can be built and interactively
adjusted to the underlying CAD geometry. This blocking can be used as a template for other similar
geometries for full parametric capabilities. Complex topologies, such as internal or external O-grids
can also be generated automatically.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 3
Introduction to ANSYS ICEM CFD
Prism
ANSYS ICEM CFD Prism generates hybrid tetrahedral grids consisting of layers of prism elements
near the boundary surfaces and tetrahedral elements in the interior for better modeling of near-
wall physics of the flow field. Compared to pure tetrahedral grids, this results in smaller analysis
models, better convergence of the solution and better analysis results.
Hybrid Meshes
The following types of hybrid meshes can be created:
• Tetra and Hexa meshes can be united (merged) at a common interface in which a layer of pyramids
is automatically created at a common interface to make the two mesh types conformal. These
meshes are suitable for models where it is preferred to have a “structured” hexa mesh in one part
and is easier to create an “unstructured” tetra mesh in another more complex part.
• Hexa-Core meshes can be generated where the majority of the volume is filled with a Cartesian
array of hexahedral elements essentially replacing the tetras. This is connected to the remainder
of a prism/tetra hybrid by automatic creation of pyramids. Hexa-Core allows for reduction in
number of elements for quicker solver run time and better convergence.
Shell Meshing
ANSYS ICEM CFD provides a method for rapid generation of surface meshes (quad and tri), both
3D and 2D. Mesh types can be All Tri, Quad w/one Tri, Quad Dominant, or All Quad. The following
methods are available:
• Mapped based shell meshing (Autoblock): Internally uses a series of 2D blocks, resulting in a
mesh better lined up with geometry curvature.
• Patch based shell meshing (Patch Dependent): Uses a series of “loops” which are automatically
defined by the boundaries of surfaces and/or a series of curves. This method gives the best quad
dominant quality and capturing of surface details.
• Patch independent shell meshing (Patch Independent): Uses the Octree method. This is the
best and most robust method for unclean geometry.
• Shrinkwrap: Used for quick generation of mesh. As it is used as the preview of the mesh, hard
features are not captured.
1. Check the mesh for problems such as holes, gaps, overlapping elements using the diagnostic checks
available. Fix the problems using the appropriate automatic or manual repair methods.
2. Check the elements for bad quality and use smoothing to improve the mesh quality.
3. If the mesh quality is poor, it may be appropriate to fix the geometry instead or recreate the mesh
using more appropriate size parameters or a different meshing method.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
4 formation of ANSYS, Inc. and its subsidiaries and affiliates.
The ANSYS ICEM CFD GUI
More information about the ANSYS ICEM CFD Output Interfaces is available from the Help menu. The
Output Interfaces option opens the ANSYS ICEM CFD Output Interfaces information in a browser. For
information about a specific interface, refer to the Table of Supported Solvers and click the name of
the interface.
Note
The default GUI style shown in Figure 2: ANSYS ICEM CFD GUI Components (p. 6) is the
Workbench style. For more information about the GUI Style options, refer to the Product-
Selection settings.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 5
Introduction to ANSYS ICEM CFD
GUI Components
The various GUI components are described in the following sections:
Main Menu
Utilities
Function Tabs
The Display Control Tree
The Message Window
The Histogram Window
The Data Entry Zone (DEZ)
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
6 formation of ANSYS, Inc. and its subsidiaries and affiliates.
The ANSYS ICEM CFD GUI
Main Menu
Figure 3: The Main Menu
File Menu
contains options for creating new or opening existing projects, loading and saving files, importing and
exporting geometry, and initializing scripting.
Edit Menu
contains Undo/Redo options, the option to open a shell window, and various internal mesh/geometry
conversion commands.
View Menu
contains various options for the standard views, view controls, and annotations.
Info Menu
allows you to get various information regarding geometry, mesh and individual entities.
Settings Menu
contains default settings for performance, graphics, and other settings most likely to be used more than
90% of the time by a specific user.
Help Menu
contains links to Help Topics, tutorials, other documentation modules, and version information.
Utilities
Figure 4: Utilities
The Utilities are icon representations of some of the most commonly used functions in the Main Menu
including opening/closing a project, undo/redo, and display options. They also include measurement
and setup of local coordinate systems.
Function Tabs
Figure 5: Function Tabs
The Function Tabs allow you to access the main functionality for the entire grid generation process.
The function tabs include: Geometry, Mesh, Blocking, Edit Mesh, Properties, Constraints, Loads,
Solve Options, and Output.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 7
Introduction to ANSYS ICEM CFD
The Display Control tree, also referred to as the Display tree, along the upper left side of the screen,
allows control of the display by part, geometric entity, element type and user-defined subsets. The tree
is organized by categories. Each category can be enabled or disabled by selecting the check box. If the
check mark is faded, some of the sub-categories are enabled and some disabled. Each category can be
expanded by selecting the “+” symbol to reveal the sub-categories. Select “-“ to collapse the tree. Since
some functions are performed only on the entities shown, the tree is an important feature to use when
isolating the particular entities to be modified. Clicking on a particular category or type using the right-
mouse button will reveal several display and modification options.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
8 formation of ANSYS, Inc. and its subsidiaries and affiliates.
The ANSYS ICEM CFD GUI
The Message Window contains all the messages that ANSYS ICEM CFD writes out to keep the user in-
formed of internal processes. The Message Window displays the communication between the GUI and
the geometry and meshing functions. Any requested information, such as measure distance, surface
area, etc. will be reported in the message window. You can use the scroll bar to review the information
from your entire session. Also, internal commands can also be typed and invoked from within the
message window.
The Save command will write all message window contents to a file. This file will be written to the
folder from which ICEM CFD was launched. The Log check box allows only user-specified messages to
be saved to a file.
Note
The Log file is unique from the file created with the Save button. This file will be written
to the starting directory, and it automatically updates as more messages are recorded.
If the check box is disabled, you can append to a file by enabling Log and accepting
an existing file name. Log will then append to this file.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 9
Introduction to ANSYS ICEM CFD
The Histogram Window shows a bar graph representing the mesh quality. The X axis represents element
quality (usually normalized to between 0 and 1) and the Y axis represents the number of elements.
Other functions which utilize this space will become pop-up menus if the quality or histogram is enabled.
Button
Check Box
A check box is used to enable/disable an item or action indicated by the check box label.
Radio Buttons
Radio buttons are a set of check boxes with the condition that only one can be enabled at a time.
When you click the left mouse button on a radio button, it will be enabled, while all others will be
disabled.
Drop-Down List
A drop-down list is a hidden single-selection list that shows only the current selection. Click the
arrow button to display the list.
Text Entry
Text entries allow you to enter text associated with the label for the field.
Number Entry
Number entries allow you to enter numerical values for the parameter indicated by the label for
the field.
Some number entry fields may have arrow buttons which allow you to increase or decrease
the value in entry field.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
10 formation of ANSYS, Inc. and its subsidiaries and affiliates.
The ANSYS ICEM CFD GUI
Selections
Selection fields indicate the entities selected for a particular operation. Click the button adjacent
to the selection field to invoke the selection mode. The selection toolbar associated with the oper-
ation will appear. After confirming the selections, the selected items will be listed in the selection
field.
Selection Toolbar
The selection toolbars contain some tools common to all select operations and some toggles for
filtering entities for selection. Some controls are linked to the hotkeys available in the select mode.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 11
Introduction to ANSYS ICEM CFD
• The help system is organized into different documentation modules which are further organized in
sections, which are listed on the Contents tab. Click the document icon or topic title next to each
section to display its content in the right windowpane.
• The Search tab allows you to view topics that contain certain words or phrases you specify. When
you execute a search, all topics containing the search text display. To go to that topic, double-click
the topic. To find out where you are in the help system, click the Contents tab. The highlighted entry
in the table of contents indicates where the topic is.
The Search tab in the Windows Help includes several capabilities to assist you in narrowing
down information returned in your searches. Some of these capabilities are:
– Using Boolean operators (AND, OR, NOT, NEAR) to precisely define search expressions.
– Using wildcard characters (*, ?) to search for expressions with identical characters.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
12 formation of ANSYS, Inc. and its subsidiaries and affiliates.
The ANSYS ICEM CFD GUI
The Search tab in the Help also includes check boxes located at the bottom of the panel that
allow you to search previous results, match similar words, or search titles only.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 13
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
14 formation of ANSYS, Inc. and its subsidiaries and affiliates.
CAD Repair
Before generating the mesh, you should confirm that the geometry is free of any flaws that would in-
hibit optimal mesh creation. If you wish to save the changes in the native CAD files, the following checks
should be performed in a direct CAD interface:
• To create a mesh, the Tetra mesher requires that the model contains a closed volume. If there are
any holes (gaps or missing surfaces) in the geometry that are larger than the local tetras, the Tetra
mesher will be unable to find a closed volume. Thus, if you notice any holes in the model prior to
mesh generation, you should fix the surface data to eliminate these holes.
• The Build Topology operation will find holes and gaps in the geometry. It should display yellow
curves where there are large (in relation to a user-specified tolerance) gaps or missing surfaces.
• During the Tetra process any leakage path (indicating a hole or gap in the model) will be indicated.
The problem can either be corrected on a mesh level, or the geometry in that vicinity can be repaired
and the meshing process repeated. For further information on the process of interactively closing
holes, see the section Tetra > Tetra Generation Steps > Useful Region of Mesh.
Close Holes
You can use the Close Holes option if the hole is bounded by more than one surface. For example, in
Figure 11: Hole Bounded by Multiple Surfaces (p. 15), the yellow curves represent the boundary of the
hole. It is clear that this hole is bounded by more than one surface.
Figure 12: Closed Hole (p. 16) shows the geometry after the Close Holes operation is completed. A new
surface is created to close the hole.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 15
CAD Repair
Remove Holes
You can use the Remove Holes option if the hole lies entirely within a single surface, such as a trimmed
surface. For example, in Figure 13: Hole Within a Single Surface (p. 16), the two yellow curve loops
represent the boundaries of the holes, which lie entirely in one surface.
Figure 14: After Remove Holes (p. 16) shows the geometry after the Remove Holes operation is com-
pleted for one of the holes. The existing surface is modified by removing the trim definition.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
16 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Fill, Trim and Blend in Stitch/Match Edges
Figure 16: Using the Fill Option (p. 17) shows the use of the Fill option.
Figure 17: Using the Trim Option (p. 17) shows the use of the Trim option.
Figure 18: Using the Blend Option (p. 18) shows the use of the Blend option.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 17
CAD Repair
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
18 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Match in Stitch/Match Edges
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 19
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
20 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Tetra Meshing
Automated to the point that you have only to select the geometry to be meshed, the Tetra mesher
generates tetrahedral meshes directly from the CAD geometry or STL data, without requiring an initial
triangular surface mesh.
Introduction
Tetra Generation Steps
Important Features in Tetra
Introduction
The Tetra mesher can use different meshing algorithms to fill the volume with tetrahedral elements
and to generate a surface mesh on the object surfaces. You can define prescribed curves and points to
determine the positions of edges and vertices in the mesh. For improved element quality, the Tetra
mesher incorporates a powerful smoothing algorithm, as well as tools for local adaptive mesh refinement
and coarsening.
• Nodes and edges of tetrahedra are matched to prescribed points and curves
• Volume and surface mesh smoothing, merging nodes and swapping edges
• Tetrahedral mesh can be merged into another tetra, hexa or hybrid mesh and then can be smoothed
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 21
Tetra Meshing
Input to Tetra
The following are possible inputs to the Tetra mesher:
• Sets of B-Spline curves and trimmed B-Spline surfaces with prescribed points
The B-Spline curves allow the Tetra mesher to follow discontinuities in surfaces. If no curves are specified
at a surface boundary, the Tetra mesher will mesh triangles freely over the surface edge. Similarly,
prescribed points allow the mesher to recognize sharp corners in the geometry. ANSYS ICEM CFD
provides tools (Build Topology) to extract points and curves to define sharp features in the surface
model.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
22 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Tetra Generation Steps
The mesh is then ready to apply loads, boundary conditions, etc., and for writing to the desired solver.
Figure 21: Curves and Points Representing Sharp Edges and Corners
Figure 22: Mesh with Curves and Points (p. 23) shows the resultant surface mesh if the curves and points
are preserved in the geometry. Mesh nodes are forced to lie along the curves and points to capture
the hard features of the geometry.
Figure 23: Mesh Without Curves and Points (p. 24) shows the resultant surface mesh if the curves and
points are deleted from the geometry. The hard features of the geometry are not preserved, but rather
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 23
Tetra Meshing
are neglected or chamfered. The boundary mesh nodes lie on the surfaces, but they will only lie on the
edges of the surfaces if curves and points are present. Removal of curves and points can be used as a
geometry defeaturing tool.
To modify the mesh size for all entities, adjust the Scale Factor, which is found under Mesh > Global
Mesh Setup. Note that if the Scale Factor is assigned a value of 0, the Tetra mesher will not run.
If the tetra sizes are larger or approximately the same size as the gap between the surfaces or curves,
the surface mesh could have a tendency to jump the gap, thus creating non-manifold vertices. These
non-manifold vertices would be created during the meshing process. The Tetra mesher automatically
attempts to close all holes in a model. Since the gap may be confused as a hole, you should either
define a thin cut, in order to establish that the gap is not a hole; or make the mesh size small enough
so that it won't close the gap when the meshing is performed. A hole is usually considered a space that
is greater than 2 or 3 elements in thickness.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
24 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Tetra Generation Steps
"Your geometry has a hole, do you want to repair it?" A jagged line will display the leakage path from
the ORFN part to the LIVE part. The elements surrounding the hole will also be displayed. To repair the
hole, select the single edges bounding it - and the mesher will loft a surface mesh to close the hole.
Further holes would be flagged and repaired in the same manner. If there are many problem areas, it
may be better to repair the geometry or adjust the meshing parameters.
At this point, the Tetra mesher balances the mesh so that elements sharing an edge or face do not
differ in size by more than a factor of 2.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 25
Tetra Meshing
Figure 26: Full Tetra Enclosing the Geometry in Wire Frame Mode
After this is done, Tetra makes the mesh conformal - that is, it guarantees that each pair of adjacent
elements will share an entire face. The mesh does not yet match the given geometry, so the mesher
next rounds the nodes of the mesh to the prescribed points, prescribed curves or model surfaces. Tetra
then "cuts away" all of the mesh, which cannot be reached by a user-defined material point without
intersection of a surface.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
26 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Tetra Generation Steps
Figure 28: Mesh after it captures surfaces and separation of useful volume
Finally, the mesh is smoothed by moving nodes, merging nodes, swapping edges and in some cases,
deleting bad elements.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 27
Tetra Meshing
The Curvature/Proximity Based Refinement value is the minimum element size to be achieved via
automatic subdivision. If the maximum size on a geometry entity is smaller than the Curvature/Prox-
imity Based Refinement value, the Tetra mesher will still subdivide to meet that requested size. The
effect is a geometry-based adaptation of the mesh.
The smoother modifies the elements with quality below the specified Up to quality value. Nodes can
be moved and/or merged, edges are swapped, and in some cases elements are deleted. This operation
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
28 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Important Features in Tetra
is then repeated on the improved grid, up to the specified number of iterations. You can choose to
smooth some element types while freezing others.
Diagnostic tools for surface meshes allow you to fill holes easily in the surface mesh. Also there are
tools for the detection of overlapping triangles and non-manifold vertices, as well as detection of
single/multiple edge and duplicate elements.
Check Mesh
Check the validity of the mesh using Edit Mesh > Check Mesh.
You can opt to use the Create subsets option for each of the problems so that they can be fixed later
or can opt to use the Check/fix each option to check and fix each one of them. Using subset manipu-
lation and mesh editing techniques, you can diagnose the problem and resolve it through merging
nodes, splitting edges, swapping edges, delete/create elements, etc.
For ease of use when working with subsets, it is usually helpful to add elements to the subset in order
to see what is happening around the problem elements. To do this, right-click on the Subset name in
the Display tree and then add layers of elements to the subset. It is also useful to display the element
nodes and/or display the elements slightly smaller than actual size. Both of these options can be accessed
by right-clicking on Mesh in the Display Tree.
Keep in mind that after mesh editing, the diagnostics should be re-checked to verify that no mistakes
were made.
There are several checks for Errors as well as Possible problems. The descriptions of each of these
checks can be found in the Edit Mesh > Check Mesh section of the Help Manual.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 29
Tetra Meshing
Smoothing iterations
This value is the number of times the smoothing process will be performed. Models with a more com-
plicated geometry will require a greater number of iterations to obtain the desired quality, which is
specified for Up to quality.
Up to quality
The Min value represents the worst quality, while the Max value represents the highest quality elements.
Usually, the Min value is set to 0.0 and the Max value is set to 1.0. The Up to quality value gives the
smoother a quality to aim for. Ideally, after smoothing, the quality of the elements should be higher
than or equal to this value. If this does not happen, you should employ other methods of improving the
quality, such as merging nodes and splitting edges. For most models, the elements should all have ratios
of greater than 0.3, while a ratio of 0.15 for complicated models is usually sufficient.
Freeze
If the Freeze option is selected for an element type, the nodes of this element type will be fixed during
the smoothing operation. As a result, this element type will not be displayed in the histogram.
Float
If the Float option is selected, the nodes of the specified element type will be capable of moving freely,
allowing nodes that are common with another type of element to be smoothed. The quality of elements
set to float is not tracked during the smoothing process and so the quality is not displayed in the histo-
gram.
The tetrahedral quality will be displayed within the Quality Histogram , where 0 represents the worst
aspect ratio and 1 represents the best aspect ratio. You may modify the display of the histogram by
adjusting the values of Min, Max, Height, and Bars. Right-click on the histogram to access the following
options for modifying its display attributes.
• The Replot option opens a small window that allows you to change the following parameters.
Clicking Accept replots the histogram to the newly set values.
Min X Value
This minimum value, which is located on the left-most side of the histogram's x-axis, represents
the worst quality elements.
Max X Value
This maximum value, which is located on the right-most side of the histogram's x-axis, represents
the highest quality that elements can achieve.
Max Y height
You can adjust the number of elements that will be represented on the histogram's y-axis. Usually
a value of 20 is sufficient. If there are too many elements displayed, it is difficult to discern the
effects of smoothing.
Num bars
This represents the number of subdivisions within the range between the Min X and Max X values.
The default Bars have widths of 0.05. Increasing the number of displayed bars will decrease their
width.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
30 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Important Features in Tetra
• The Reset option will return all of the values back to their original settings.
• Show: Click the left mouse button on any of the bars in the histogram to select elements that fall
within that selected Quality range. If Show is enabled, the selected elements on the model will become
visible in the main viewing window. The following options control how the selected elements are
displayed.
• Solid: Enabling this option will display the elements as solid, rather than the default grid representation.
(Show must be enabled.)
• Color by Quality: If available, enabling this option will display the elements in the same color as the
selected Quality bar in the histogram. (Show must be enabled.)
• Highlight: If available, this option allows you to display one or two additional layers adjacent to the
selected elements. (Show must be enabled.)
• Subset: Allows you to create a Subset containing only the elements chosen from the Quality histogram.
The visibility of this subset is controlled by Subset in the Display Tree. The Add select option allows
you to add elements to an already established subset.
Quality Metrics
This option allows you to modify the histogram display.
The histogram displays the overall quality of the mesh. The x-axis measures the quality, with 0 repres-
enting poor quality and 1 representing high quality. The y-axis measures the number of elements that
belong within each quality sub-range.
For descriptions of all the quality metrics, refer to the Edit Mesh > Display Mesh Quality section in the
Help Manual.
Stay on geometry
The default is, when a grid is smoothed, the nodes are restricted to the geometry -- surface, curves and
points -- and can be moved only along the geometrical entities to which they are associated.
Violate Geometry
Enabling this option allows the smoothing operation to yield a higher quality mesh by violating the
constraints of the geometry. The nodes can be moved off the geometry to obtain better mesh quality,
as long as the movement remains within the absolute distance specified.
Relative Tolerance
This option works in the similar fashion as Violate Geometry except that the distance is relative here.
Allow refinement
If the quality of the mesh cannot be improved through normal algebraic smoothing, the Allow refinement
option will allow the smoother to automatically subdivide elements to obtain further improvement. After
smoothing with Allow refinement enabled, it may be necessary to smooth further with the option dis-
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 31
Tetra Meshing
abled. The goal is to reduce the number of elements that are attached to one vertex by refinement in
problem regions.
Laplace smoothing
This option will solve the Laplace equation, which will generally yield a more uniformly spaced mesh.
Note
This can sometimes lead to a lower determinant quality of the prisms. Also, this option
works only for the triangular surface mesh.
Surface fitting
This option will smooth the mesh, keeping the nodes and the new mesh restricted to the surface of the
geometry. Only Hexa models will utilize this option.
Ignore PrePoints
This option will allow the smoother to attempt to improve the mesh quality without being bound by
the initial points of the geometry. This option is similar to the Violate geometry option, but works only
for points located on the geometry. This option is available only when there are hexahedral elements
in the model. Usually, the best way to improve the quality of grids that cannot be smoothed above a
certain level is to concentrate on the surface mesh near the bad elements and edit this surface mesh to
improve the quality.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
32 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Prism Mesh
Tetra meshing is not efficient for capturing shear or boundary layer physics. Prism mesh efficiently
captures these effects near the surface while maintaining the ease and automation of Tetra mesh. Prism
has always been necessary for CFD customers, but now that the option is more widely available, many
other branches of CAE have started using prisms to better resolve the physics perpendicular to the
surfaces of their models. With ANSYS ICEM CFD, Prism and Tetra generation is automatic and intelligent.
The spacing of the prism layers to capture the Y+ for Navier-Stokes mesh is the primary concern. The
rate of volume change between cells is also important. Calculations are done between nodes or elements,
and Prism mesh gives you more elements perpendicular to the surface. This is an efficient way to achieve
better resolution (more calculations per unit distance) of the solution normal to the surface, without
increasing the number of elements along the surface. This gives you a quicker and more accurate
solution than can be achieved with a very fine tetra mesh.
The height and direction of the prism layer extrusion are calculated on an element by element basis
and may vary due to global or local controls, or for improved quality. You may choose to set the initial
height, number of layers and growth ratio, which are then used to determine the Prism height limit
factor. Or you may prefer to set only the number of layers and growth ratio, which then allows Prism
to adjust the initial height and locally optimize the volume transition between the prisms and tetras.
Users concerned about Y+ can then adjust the first cell height using Edit Mesh > Split Mesh > Split
Prisms.
Prism parameters are set globally, but can then be adjusted on a part by part or entity by entity basis.
Entity settings override global settings, and between entities the smaller size overrides the larger. For
instance, 3 layers could be set for a growth rate of 1.2 globally, but a certain part could be set for 5
layers. Setting a specific parameter on a single entity within that part or another part is handled intelli-
gently. For example, if you set a local parameter such as height on a single curve entity, Prism will in-
terpolate that parameter smoothly across the surface between curves.
You may notice that you can also select volume parts for prism. If no volume parts are selected, it will
assume that you want to grow prisms into all volumes bordering the prism surfaces. If you select spe-
cific volume parts, then prism will be grown only into those volumes.
After each layer is extruded, smoothing is done according to the global settings. The layers are grown
one at a time. This continues until all the requested layers are grown. You can add prisms to exiting
layers or you can subdivide and redistribute layers at a later date. You can save time by growing only
a few thicker layers and then subdividing them into many layers. The smoothing is the most time con-
suming part, so for simple configurations, it may be best to turn off all smoothing but grow all the
layers one at a time. This allows you to take advantage of the variable height feature.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 33
Prism Mesh
Note
If the existing volume mesh is tet/hexa mesh, on the hexa side the prisms will be added
within the first hexa layer.
Note
If many prism layers are needed, it is faster and can be more robust to create initial thick
prism layers and then split them to create the total desired number of prism layers using
Edit Mesh > Split Mesh > Split Prisms.
• Check and fix all diagnostics. Single/multiple edges, Non-manifold vertices, and Duplicate elements
will crash the prism mesher.
• Visually scan the surface mesh. Look for any surface discrepancies or sharp tent-like structures in
the mesh.
Look for a few elements of one part scattered among another part. Extruding from a few
isolated elements will likely crash the prism mesher. Modify part assignments of such elements.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
34 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Prism Mesh Process
• Use the Smoothing Options for Tetra and Tri surface mesh under Mesh > Prism before creating
prism mesh.
• Laplace Triangle Quality type is typically best for eventual prism quality.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 35
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
36 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Hexa
Hexa is a 3D object-based, semi-automatic, multi-block structured and unstructured, surface and volume
mesher.
Introduction
Features of Hexa
Mesh Generation with Hexa
The Hexa Database
Intelligent Geometry in Hexa
Unstructured and Multi-block Structured Meshes
Blocking Strategy
Automatic O-grid generation
Edge Meshing Parameters
Smoothing Techniques
Refinement and Coarsening
Replay Functionality
Periodicity
Pre-Mesh Quality
Most Important Features of Hexa
Introduction
Hexa represents a new approach to hexahedral mesh generation. The block topology model is generated
directly on the underlying CAD geometry. Within an easy-to-use interface, those operations most often
performed by experts are readily accessible through automated features.
There is access to two types of entities during the mesh generation process in Hexa: block topology
and geometry. After interactively creating a 3-D block topology model equivalent to the geometry, the
block topology may be further refined through the splitting of edges, faces and blocks. In addition,
there are tools for moving the block vertices, either individually or in groups, onto associated curves
or CAD surfaces. You may also associate specific block edges with important CAD curves to capture
important geometric features in the mesh.
Moreover, for models where you can take advantage of symmetry conditions, topology transformations
such as translate, rotate, mirror and scaling are available. The simplified block topology concept allows
rapid generation and manipulation of the block structure and, ultimately, rapid generation of the
hexahedral meshes.
Hexa provides a projection-based mesh generation environment where, by default, all block faces
between different materials are projected to the closest CAD surfaces. Block faces within the same
material may also be associated to specific CAD surfaces to allow for definition of internal walls. In
general, there is no need to perform any individual face associations to underlying CAD geometry,
which further reduces the difficulty of mesh generation.
Features of Hexa
Some of the more advanced features of Hexa include:
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 37
Hexa
O-grids: For very complex geometry, Hexa automatically generates body-fitted internal and external
O-grids to parametrically fit the block topology to the geometry to ensure good quality meshes.
Time Saving Methods: Hexa provides time saving surface smoothing and volume relaxation algorithms
on the generated mesh.
Mesh Quality Checking: With a set of tools for mesh quality checking, elements with undesirable
skewness or angles may be displayed to highlight the block topology region where the individual blocks
need to be adjusted.
Mesh Refinement/Coarsening: Refinement or coarsening of the mesh may be specified for any block
region to allow a finer or coarser mesh definition in areas of high or low gradients, respectively.
Replay Option: Replay file functionality enables parametric block topology generation linked to para-
metric changes in geometry.
Symmetry: As necessary in analyzing rotating machinery applications, for example, Hexa allows you
to take advantage of symmetry in meshing a section of the rotating machinery thereby minimizing the
model size.
Link Shape: This allows you to link the edge shape to existing deforming edge. This gives better control
over the grid specifically in the case of parametric studies.
Adjustability: Options to generate 3D surface meshes from the 3D volume mesh and 2D to 3D block
topology transformation.
• Import a geometry file using any of the direct, indirect or faceted data interfaces.
• Interactively define the block model through split, merge, O-grid definition, edge/face modifications
and vertex movements.
• Check the block quality to ensure that the block model meets specified quality thresholds.
• Assign edge meshing parameters such as maximum element size, initial element height at the
boundaries and expansion ratios.
• Generate the mesh with or without projection parameters specified. Check the Mesh quality to ensure
that specified mesh quality criteria are met.
If necessary, you may always return to previous steps to manipulate the blocking if the mesh quality
does not meet the specified threshold or if the mesh does not capture certain geometry features. The
blocking may be saved at any time, thus allowing you to return to previous block topologies.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
38 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Unstructured and Multi-block Structured Meshes
Additionally, at any point in this process, you can generate the mesh with various projection schemes
such as full face projection, edge projection, point projection or no projection at all.
Note
In the case of no projection, the mesh will be generated on the faces of the block model
and may be used to quickly determine if the current blocking strategy is adequate or if it
must be modified.
• Vertices: corner points of blocks, of which there are at least eight, that define a block
The geometry is selected in the CAD system and tagged with information (made intelligent) for grid
generation such as boundary conditions and grid sizes, and this intelligent geometry information is
saved with the master geometry.
In Hexa, by updating all entities with the update projection function, blocking vertices projected to
prescribed points in the geometry are automatically adapted to the parametric change and one can
recalculate the mesh immediately. Additionally, with the use of its Replay functionality, Hexa provides
complete access to previous operations.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 39
Hexa
Additionally, without merging any of the nodes at the block interfaces, the Output Block option allows
you to minimize the number of output files generated with the multi-block structured approach.
Blocking Strategy
With Hexa, the basic steps necessary to generate a hexahedral model are the same, regardless of
model complexity. The blocking topology, once initialized, can then be modified by splitting and merging
the blocks, as well as through the use of an operation called O-grid (Refer to the next section). While
these operations are performed directly on the blocks, the blocks may also go through indirect modific-
ation by altering the sub-entities of the blocks (i.e.: the vertices, edges, faces).
Upon initialization, Hexa creates one block that encompasses the entire geometry. The subsequent
operations under the Blocking menu of developing the block model, referred to as "blocking the geo-
metry," may be performed on a single block or across several blocks.
Note
Colors of Edges:
Note
Red Vertices
These vertices are projected to prescribed points.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
40 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Automatic O-grid generation
The ability to convert blocks from free to mapped or vice versa imposes constraints on the blocking
and resulting mesh. By imposing more constraints, you can enforce a greater number of hexa elements,
while reducing the constraints can sometimes improve mesh transitioning.
Split
The Split function, which divides the selected block interactively, may be applied across the entire block
or to an individual face or edge of a block by using the Split face or Split edge options, respectively.
Blocks may be isolated using the Index control.
Merge
The Merge function works similar to split blocks; one can either merge the whole block or merge only
a face or an edge of the block.
While some models require a high degree of blocking skill to generate the block topology, the block
topology tools in Hexa allow you to quickly become proficient in generating a complex block model.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 41
Hexa
Figure 32: Initial block, Block with O-Grid, O-Grid with Add Face
Using the Add face option, an O-grid may be created such that the O-grid passes through the selected
block face(s). In Figure 32: Initial block, Block with O-Grid, O-Grid with Add Face (p. 42), the Add Face
option was used on the last block to include one face on the block prior to generating the O-grid.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
42 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Edge Meshing Parameters
The blocks may also be modified by moving the vertices of the blocks and by defining specific rela-
tionships between the faces, edges and vertices to the geometry.
You can use the following pre-defined bunching laws or Meshing laws:
• Uniform
• Hyperbolic
• Poisson
• Curvature
• Geometric 1
• Geometric 2
• Exponential 1
• Exponential 2
• Bi-Exponential
• Linear
• Spline
You may modify these existing laws by applying pre-defined edge meshing functions, accessible through
the Meshing > Edge Params > Graphs option in Hexa.
• Constant
• Ramp
• S curve
• Parabola Middle
• Parabola Ends
• Exponential
• Gaussian
• Linear
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 43
Hexa
• Spline
Note
By selecting the Graphs option, you may add/delete/modify the control points governing
the function describing the edge parameter settings. Additional tools such as Linked
Bunching and the multiple Copy buttons provide you with the ability to apply the
specified edge bunching parameters quickly to the entire model.
Smoothing Techniques
In Hexa, both the block topology and the mesh may be smoothed to improve the overall block/mesh
quality either in a certain region or for the entire model. The block topology may be smoothed to improve
the block shape prior to mesh generation. This reduces the time required for development of the block
topology model.
The geometry and its associative surfaces, curves, and points are all constraints when smoothing the
block topology model. Once the block topology smoothing has been performed, you may smooth the
mesh after specifying the proper edge bunching parameters.
The quality criteria for smoothing are described in the Help Manual, under Blocking > Pre-Mesh Quality.
Refinement
The refinement capability is used for solvers that accept non-conformal node matching at the block
boundaries. The refinement capability is used to minimize the model size, while achieving proper mesh
definition in critical areas of high gradients. Entering a scale factor greater than 1 will result in refinement.
Coarsening
In areas of the model where the flow characteristics are such that a coarser mesh definition is adequate,
coarsening of the mesh may be appropriate to contain model size. Entering a scale factor less than 1
will result in coarsening.
Replay Functionality
Parametric changes made to model geometry are easily applied through the use of Hexa's replay
functionality, found in File > Replay Scripts. Changes in length, width and height of specific geometry
features are categorized as parametric changes. These changes do not, however, affect the block topology.
Therefore, the Replay function is capable of automatically generating a topologically similar block
model that can be used for the parametric changes in geometry.
If any of the Direct CAD Interfaces are used, all geometric parameter changes are performed in the
native CAD system.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
44 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Periodicity
You can also use variables in the replay script to parametrize edge parameters. Refer to Using Variables
in the Replay Script in the User Guide for details.
The variables for the edge parameters are set at the top of the replay file. Within the script, the '$' in-
dicates a variable. To parametrize the edge parameters, you may update the variables at the top of the
script and then rerun the script.
Periodicity
Periodic definition may be applied to the model in Hexa. The Periodic nodes function, which is found
under Blocking > Periodic nodes, plays a key role in properly analyzing rotating machinery applications,
for example. Typically, you will model only a section of the rotating machinery, as well as implement
symmetry, in order to minimize the model size. By specifying a periodic relationship between the inflow
and outflow boundaries, the particular specification may be applied to the model—flow characteristics
entering a boundary must be identical to the flow characteristics leaving a boundary.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 45
Hexa
Pre-Mesh Quality
The pre-mesh quality functions are accessible through Blocking > Pre-Mesh Quality. Applying any of
the quality checks will yield a histogram plot.
Determinant
The Determinant check computes the deformation of the elements in the mesh by first calculating of
the Jacobian of each hexahedron and then normalizing the determinant of the matrix. A value of 1
represents a perfect hexahedral cube, while a value of 0 is a totally inverted cube with a negative
volume.
The mesh quality, measured on the x-axis, of all elements will be in the range from 0 to1. If the determ-
inant value of an element is 0, the cube has one or more degenerated edges. In general, determinant
values above 0.3 are acceptable for most solvers. The subdivision across the quality range is determined
by the number of assigned Bars
The y-axis measures the number of elements that are represented in the histogram. This scale ranges
from 0 to a value that is indicated by the Height.
Angle
The Angle option checks the maximum internal angle deviation from 90 degrees for each elements.
Various solvers have different tolerance limits for the internal angle check. If the elements are distorted
and the internal angles are small, the accuracy of the solution will decrease. It is always wise to check
with the solver provider to obtain limits for the internal angle threshold.
Volume
The Volume check will compute the internal volume of the elements in the model. The units of the
volume will be displayed in the unit that was used to create the model.
Warpage
The Warpage check will yield a histogram that indicates the level of element distortion. Nodes that are
in-plane with one another will produce an element with small warpage. Nodes that make elements
twisted or distorted will increase a element's distortion, giving a high degree of warpage. The y-axis is
the scale for the number of elements represented in the histogram - a value determined by the assigned
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
46 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Most Important Features of Hexa
Height. The x- axis, which ranges from a Min of 0 to a Max of 90, is the degree of warpage that an
element experiences.
• Modern GUI and software architecture with the latest hexahedral mesh technology
• Extensive solver interface library with over 100 different supported interfaces
• Mesh refinement to provide adequate mesh size in areas of high or low gradients
• Extensive selection of mesh bunching laws including the ability to graphically add/delete/modify
control points defining the graph of the mesh bunching functions
• Topology operations such as translate, rotate, mirror, and scaling to simplify generation of the topology
model
• Quality checks for determinant, internal angle and volume of the meshes
• Output block definition to reduce the number of multi-block structured output mesh files
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 47
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
48 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Properties
The Properties menu allows you to create different materials by specifying material or element properties,
such as type, the Young's Modulus, and Poisson's ratio. Once the material is created, you can apply
those properties to the elements.
Create Material Property
Save Material
Open Material
Define Table
Define Element Properties
Save Material
The Write Material File option allows you to save the material specification so that it may be reused
whenever necessary. The material file will be saved with the .mat extension.
Open Material
The Load Material From File option allows you to open a material file to be used in your design, or
modified and saved for future use.
Define Table
The Create Table option allows you to create your material property empirically by entering values for
x and y ,You may even visualize the graph of the property.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 49
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
50 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Constraints
From the Constraints tab, you can define the motion restrictions on different entities such as points,
curves, surfaces, or subsets, as well as define other options such as Contact definition, Velocity and
Rigid Wall.
Create Constraint / Displacement
Define Contact
Define Single Surface Contact
Define Initial Velocity
Define Planar Rigid wall
Define Contact
This option allows you to define contacts by Automatic Detection or Manual Definition.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 51
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
52 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Loads
In this tab, there are several options available for applying internal and external loads, such as force,
pressure, and temperature. How ICEM CFD treats the load depends on how the load is applied - to a
curve, a surface, or a mesh. In all cases, the load information is not calculated until the user is creating
the output files for one of the supported "Common Structural" solvers, – ANSYS, AUTODYN, LS-DYNA,
ABAQUS, or NASTRAN. That is, the output file is generated thru the Solve Options Tab, and at this time,
the loads will be written out according to the selected solver's published format.
Theory
By Curve
The total Force 'FT' may be applied on a curve as shown below. Applying the load to a geometry entity
simplifies the process for you and keeps the load information at the geometry level so the mesh can
be regenerated without losing the setup information.
Nodes are numbered 0, 1, 2, and so on. Elements between the nodes have lengths L1, L2 and so on.
The total length is LT.
Then the force on the Nodes, as per FEA concepts, is distributed linearly in proportion to the Element
length as shown in the figure below.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 53
Loads
In general, the force at any Node is: Fi = Sum [ FT * (Lj / LT) * (1 / Nj) ], where i is the node number, j
is the element number, Lj is the length of element j, and Nj is the number of Nodes attached to element
j.
As a check, if you add the individual node forces, F0 + F1 + F2 + F3 + F4, then the result equals FT.
By Mesh Elements
You may also apply loads directly to the elements (select the elements directly rather than the geometry
entities).This may occur, for example, if you don’t have the geometry in a particular model or area of a
model. In this case, the load is distributed element-by-element using a Quadratic distribution as shown.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
54 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Figure 35: Force on Elements with mid-side nodes
Node numbers and element lengths are defined as before. In addition, each element has a mid-side
node labelled m1, m2, and so on.
The Quadratic Load distribution, as per FEA concepts on an element-by-element basis is shown in Fig-
ure 36: Quadratic Load Distribution (p. 55).
The distribution of the Total Force, FT, at the boundary nodes is as follows:
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 55
Loads
As in the previous case of linear distribution, you can check the total Force by adding the individual
nodal forces:
By Surface
If you choose to set a load on a surface entity, then the load distribution follows the Nine Node, Two
Dimension, Lagrange distribution. See the Figure 37: QUAD 9 Element (p. 56) for an illustration.
Nine nodes are identified: N1-N4 at the corners; N5-N8 at the mid-sides; and N9 in the middle. The symbols
ξ and η define a local coordinate system for the development of the load distribution, and vary from
–1 to +1 over the surface of the element.
= − −
At a Mid-Side Node, the Shape function for the distribution is:
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
56 formation of ANSYS, Inc. and its subsidiaries and affiliates.
− −
=
And finally, the Shape function for the Middle Node load distribution is:
= − −
Suppose a Force F is uniformly distributed over the whole Area. Then the pressure is P = F / 4. (Because
in the ξ-η coordinate system the area of the surface is 4.)
To find the Consistent Load at each Node, we must integrate the Shape function over the surface area:
= ∫ == − ∫ == −
=
Consistent Load at Node 5 = L5:
$ = ∫ == !− ! ∫ == !− !$ = "#
Consistent Load at Node 9 = L9:
Substituting this value in the above equations we get the Consistent Load as
L1 = F / 36
L5 = F / 9
L9 = 4F / 9
By symmetry, the Consistent Load on all corner nodes N1, N2, N3, and N4 are equal.
Similarly, the Consistent Load on all mid-side nodes N5, N6, N7, and N8 are equal.
As with the Linear and Quadratic distributions, a check against the Total can be performed.
= F / 9 + 4F / 9 + 4F / 9
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 57
Loads
= FT
Note
A similar process for calculating the Consistent Load on a QUAD8 element load distribution
is available. Again, the output file is generated thru the "Solve Options" Tab, and during
output, the distributed load information will be written out according to the selected solver's
published format.
Force
Using this option, you can apply translational (force) or rotational (moment) loads on entities in all three
directions.
Forces can be applied by two different options. The Uniform option applies the stated force at all selected
entities. For example with curves, the Uniform option will apply the full force to all nodes attached to
the curve. The Total option means that the force gets distributed among all the nodes of the selected
entities according to FEA concepts.
Pressure
You can apply pressure loads to surfaces, subsets, or parts. See the Help for more detail.
Temperature
This option allows you to apply temperature to points, curves, surfaces, bodies, and subsets.See the
Help for more Detail.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
58 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Solve Options
Setup Solver Parameters has options for specifying the solver parameters. You can also specify the
analysis solution parameters.
Setup Sub-Case
You can create subcases to apply the load in different steps.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 59
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
60 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Workbench Integration
The data-integrated ICEM CFD component system enables you to launch ICEM CFD from ANSYS Work-
bench and use it to build a project using upstream data from Geometry, Mesh, or combined Geometry
and Mesh system components, and to use ICEM CFD to provide data to downstream component systems,
such as ANSYS FLUENT, ANSYS CFX, ANSYS POLYFLOW, and FE Modeler.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 61
Workbench Integration
• ICEM CFD system header. The System Header identifies the component type and provides access to
Workbench context menu options. The ICEM CFD system header context menu options include:
– Refresh
– Update
– Delete
– Rename
– Properties
– Add/Edit Note
These standard actions are described in System Header Context Menu Options in the Workbench User
Guide.
Note
If available, Update will use the ICEM CFD Replay file to update the ICEM CFD project.
Note
Scripts written in ICEM CFD may not be parametric with upstream or downstream projects.
Care should be taken to write scripts whose functions do not exceed the capabilities of the
upstream or downstream component systems.
• Model cell. The Model Cell is associated with the ICEM CFD application. You can use the Model Cell to
modify some aspects of the project. You can also double-click the Model Cell to open the project in ICEM
CFD. The Model cell context menu items include the following:
– Edit: Opens the ICEM CFD application and loads an existing Geometry/ICEM CFD file.
– Transfer Data From New: Enables the transfer of data from upstream Geometry, Mesh, or combined
Geometry and Mesh components.
– Transfer Data to New: Enables the transfer of data from an ICEM CFD project to downstream data-in-
tegrated system projects, such as:
→ FLUENT
→ CFX
→ FE Modeler
→ POLYFLOW
– Update, Refresh, Reset, Rename, Properties, and Add/Edit Note. These standard actions are described
in System Header Context Menu Options in the Workbench User Guide.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
62 formation of ANSYS, Inc. and its subsidiaries and affiliates.
• Parameters cell (optional). The Parameters Cell enables you to see and edit Input and Output parameters
for ICEM CFD.
• Drag-and-drop the ICEM CFD system template onto the Project Schematic.
• Right-click on a Geometry or Mesh project and select Transfer Data to New> ICEM CFD.
Updating Projects
Updating a project in Workbench brings the entire ICEM CFD system up to the most current status, in-
cluding upstream and downstream data.
Note
Named selections defined in Mesh systems are available only within the Mesh system. They
are not available to downstream systems like ICEM CFD.
The actions taken by Workbench depend on whether the following conditions are met:
• Blocking exists.
The following table describes the actions performed by ICEM CFD according to these conditions:
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 63
Workbench Integration
c. Converts pre-
mesh to unstruc-
tured.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
64 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Blocking Replay Blocking Input Other Input Actions performed
File Parameters Parameters by ICEM CFD
4. Converts pre-mesh
to unstructured.
c. Converts pre-
mesh to unstruc-
tured.
The order of operations is Meshing input parameters are set before the Replay file is run; Blocking Input
parameters are set after a replay file is run, but only if blocking exists after the replay file is run.
If no Replay file exists, the default mesher is determined by the presence or absence of blocking: if no
blocking exists in the project, tetra is the default. Conversely, if blocking exists in the project, hexa is
the default mesher.
You can ensure that you are working within the data integrated environment by checking the Message
window within ICEM CFD. The first line identifies that the application is integrated in the Workbench
Framework.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 65
Workbench Integration
One-Click Menus
The following one-click menu options are available in the Toolbar when you open ICEM CFD from
Workbench:
• Refresh Project: Refreshes the upstream data in the ICEM CFD project.
• Update Project: Brings the entire ICEM CFD system up to the most current status, including upstream
and downstream data.
• Start Replay Recording: Begins recording the commands needed to generate the block topology
model. All of the steps in the mesh development process are recorded, including blocking, mesh size,
edge meshing, boundary condition definition, and final mesh generation. See Replay Functionality in
the ANSYS ICEM CFD User Manual. After you click the Start Replay Recording Icon, the icon changes
to the Stop Replay Recording icon. You can click this icon to stop recording.
You can also click on the arrow to choose Pause Replay Recording, Run Replay File, or Delete
Replay File.
• Output Mesh: You can choose to save the ICEM CFD mesh output to FLUENT, CFX, or POLYFLOW
projects.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
66 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Setting Parameters
Setting Input parameters in Workbench enables you to pass parameters to ICEM CFD and other down-
stream analysis tools. The interaction of parameters between applications provides you with greater
flexibility and capabilities to run optimization and what-if scenarios. For more information about using
parameters in Workbench, see Working with Parameters and Design Points in the Workbench User Guide.
Parameters may be set globally or individually, with individual parameters taking precedence over
global values.
• Global Mesh Size (See Global Mesh Size in the ANSYS ICEM CFD Help Manual).
• Shell Meshing (See Shell Meshing Parameters in the ANSYS ICEM CFD Help Manual).
• Volume Meshing (See Volume Meshing Parameters in the ANSYS ICEM CFD Help Manual).
• Prism Meshing (See Prism Meshing Parameters in the ANSYS ICEM CFD Help Manual).
• Surface Mesh Setup (See Surface Mesh Setup in the ANSYS ICEM CFD Help Manual).
• Curve Mesh Setup (See Curve Mesh Setup in the ANSYS ICEM CFD Help Manual).
• Edge Params (See Edge Params in the ANSYS ICEM CFD Help Manual).
For Surface Mesh Setup, Curve Mesh Setup, and Edge Params, you can set parameters either
on all existing surfaces or curves and edges at once, or for a single curve, surface, or edge.
1. Within ICEM CFD, choose any of the input parameters listed above.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 67
Workbench Integration
3. Click the Yes button in the pop-up dialog to confirm the selection. A P in the check box indicates that
the parameter has been created for Workbench.
Note
You will not be able to edit the parameter within ICEM CFD unless you click the check
box again and deselect the parameter.
You can now update the project using the new parameter settings.
1. Within ICEM CFD, open the Surface Mesh Setup, Curve Mesh Setup, or Edge Params parameters from
the Tab menu.
3. Click the Left Mouse button to select the curve, surface, or edge for which you want to set parameters.
The surface, curve, or edge you selected are listed in the selection entry.
5. Select the check box next to the parameter you want as the input parameter.
6. Click the Yes button in the pop-up dialog to confirm the selection. A P in the check box indicates that
the parameter for the single surface, curve or edge has been created for Workbench.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
68 formation of ANSYS, Inc. and its subsidiaries and affiliates.
Setting the parameters for all existing curves, surfaces, or edges
1. Within ICEM CFD, open the Surface Mesh Setup, Curve Mesh Setup, or Edge Params parameters from
the Tab menu.
2. Leave the Surface, curve, or edge selection field empty (do not select any surface, curve or edge).
3. Select the check box next to the parameter you want as the input parameter
4. Click the Yes button in the pop-up dialog to confirm the selection. A P in the check box indicates that
the parameter for all existing surfaces, curves or edges has been created for Workbench.
1. Within ICEM CFD, choose Settings>Workbench Parameters> Workbench Input Parameters (User-
defined).
2. In the User-Defined Workbench Input Parameters window, check the Create User Defined Input
Parameter check box.
4. Enter a value for the Parameter (for example, 1.343). This value must not be empty.
You can edit this value in the Outline of Schematic: Parameters window.
Note
See the ANSYS ICEM CFD Programmer's Guide for information about using User-Defined
Parameters with Replay Scripting.
1. Within ICEM CFD, choose Settings>Workbench Parameters> Workbench Input Parameters (User-
defined).
2. In the User-Defined Workbench Input Parameters window, check the Delete User Defined Input
Parameter check box.
3. Use the drop-down menu to choose the name of the parameter you want to delete.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 69
Workbench Integration
2. Optionally, Click the Output quality metrics check box to select quality metrics.
a. Use the Quality Metrics drop-down menu to choose the metric you want to set.
b. Click the radio buttons to select the mesh types to check for the metric.
a. Check the boxes next to the element types you want an output for.
2. In the Workbench Output Parameters window, check the Delete all quality metrics output parameters
check box and/or the Delete all number of elements output parameters check box.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
70 formation of ANSYS, Inc. and its subsidiaries and affiliates.
1. In the Workbench Toolbox, double-click the ICEM CFD component to start the data-integrated ICEM
CFD component system.
3. First, create an Input parameter, ZSIZE, that you can manipulate from Workbench.
d. Click OK to finish.
.
4. Now create a box model upon which you will perform a meshing operation. Record the process so the
operation can be performed again when you update it from Workbench.
g. Click Yes on the pop-up dialog to use autosizing for the mesh size.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
formation of ANSYS, Inc. and its subsidiaries and affiliates. 71
Workbench Integration
a. In the Workbench Project Schematic window, double-click on the Parameters cell of the ICEM CFD
component.
You can watch the Replay script run using the new parameter in the ICEM CFD interface. Each time
you change the ZSIZE parameter in Workbench, will be generated and meshed with the new ZSIZE
parameter value.
ANSYS ICEM CFD 14.5 - © SAS IP, Inc. All rights reserved. - Contains proprietary and confidential in-
72 formation of ANSYS, Inc. and its subsidiaries and affiliates.