Professional Documents
Culture Documents
Table of Contents
Note: The internal capacity, displacement, and annular capacity values listed in Table
P.1 make no allowances for tool joint dimensions and should NOT be used for
critical displacement operations such as cement squeezing.
DUPLEX PUMPS
Barrels per Inch of Stroke
----------------------------------------------Fluid Piston Rod Diameter (inches) ---------------------------------------------
Liner 1-1/2 1-3/4 1-7/8 2 2-1/4 2-3/8 2-1/2 2-3/4 3 3-1/8 3-1/4
Size
(inches)
3-1/2 0.00360
3-3/4 0.00419 0.00460 0.00398 00.0391
4 0.00482 0.00486 0.00461 0.00453
4-1/4 0.00548 0.00535 0.00528 0.00520
4-1/2 0.00619 0.00606 0.00599 0.00591 0.00574 0.00564 0.00555 0.00533 0.00510 0.00498 0.00485
4-3/4 0.00694 0.00681 0.00674 0.00666 0.00649 0.00639 0.00629 0.00608 0.00585 0.00572 0.00560
5 0.00773 0.00760 0.00753 0.00745 0.00728 0.00718 0.00708 0.00687 0.00664 0.00651 0.00638
5-1/4 0.00856 0.00843 0.00836 0.00828 0.00811 0.00801 0.00791 0.00770 0.00747 0.00734 0.00721
5-1/2 0.00943 0.00930 0.00923 0.00915 0.00898 0.00888 0.00878 0.00857 0.00834 0.00821 0.00808
5-3/4 0.01034 0.01021 0.01014 0.01006 0.00989 0.00979 0.00969 0.00948 0.00925 0.00912 0.00900
6 0.01129 0.01116 0.01109 0.01101 0.01084 0.01074 0.01064 0.01043 0.01020 0.01008 0.00995
6-1/4 0.01228 0.01215 0.01208 0.01200 0.01183 0.01174 0.01164 0.01142 0.01119 0.01107 0.01094
6-1/2 0.01332 0.01318 0.01311 0.01303 0.01296 0.01277 0.01267 0.01246 0.01222 0.01210 0.01197
6-3/4 0.01439 0.01426 0.01418 0.01411 0.01393 0.01384 0.01374 0.01353 0.01330 0.01317 0.01304
7 0.01550 0.01537 0.01530 0.01522 0.01505 0.01495 0.01485 0.01464 0.01441 0.01429 0.01416
TRIPLEX PUMPS
Liner Diameter Displacement
(inches) (bbls / inch of stroke)
3-1/2 0.002976
3-3/4 0.003416
4 0.003886
4-1/4 0.004387
4-1/2 0.004919
4-3/4 0.005480
5 0.006073
5-1/4 0.006695
5-1/2 0.007348
5-3/4 0.008031
6 0.008744
6-1/4 0.009488
6-1/2 0.010263
6-3/4 0.011067
7 0.011902
GENERALIZED PROCEDURES
Step One:
Determine “Barrels / Inch of Stroke” by using the appropriate pump table, or the
following equations:
(Linear Diameter)²
Barrels / Inch of Stroke = --------------------------- (Triplex)
4116
Figure P.1a
Pc Max (Part 1) for Driller's Method
Figure P.1b
PcMax (Part 2) for Driller's Method
Figure P.2a
PcMax (Part 1) for Engineer's Method
Figure P.2b
PcMax (Part 2) for Engineer's Method
Figure P.3
Volume of Gas at Surface (Driller's and Engineer's Method)
where: PR
= Reservoir Pressure (psi)
H1
= Height of Bubble (ft) {Pit Gain / ACF (DP X CSG)}
r1
= Pressure Gradient of OMW (psi/ft)
TZ
= Temperature/Gas Compressibility (Figure P.5) or
= 4.03 - 0.38 ln (PR)
2.0 Engineer’s Method Worksheet
where: PR
= Reservoir Pressure (psi)
H1
= Height of Bubble (ft) {Pit Gain / ACF (DP X CSG)}
r2
= Pressure Gradient of KMW (psi/ft)
TZ
= Temperature/Gas Compressibility (Figure P.5) or
= 4.03 - 0.38 ln (PR)
3.0 Volume of Gas at Surface
PcMax
V = V2 - V1
PRV1TZ
where: V2 = -----------
PcMax
V = V2 - V1
PRV1TZ
where: V2 = -----------
PcMax
VDPC (ft.)
D1 = --------------
AV
V1
_______
H (ft) = (if answer is equal to or less than drill collar length)
ADC
V1 - (ADC) (L)
= ---------------------- + L, ft.
AV
(if answer above is greater than drill collar length)
V1
_______
H1 (ft) = (annulus constant)
AV
Hydril
Manual 7-1/16 3000 7-1/16 3000 Max. 1.00 0.93 4.8:1 1.5:1
Lock 7-1/16 5000 7-1/16 3000 Max. 1.00 0.93 4.8:1 1.5:1
Pipe 7-1/16 10000 7-1/16 3000 Max. 1.90 2.00 7.7:1 1.7:1
7-1/16 15000 7-1/16 3000 Max. 3.70 3.40 7.1:1 6.6:1
9 3000 9 3000 Max. 1.90 1.90 4.5:1 2.6:1
9 5000 9 3000 Max. 1.90 1.90 4.5:1 2.6:1
11 3000 11 3000 Max. 3.30 3.20 6.0:1 2.0:1
11 5000 11 3000 Max. 3.30 3.20 6.0:1 2.0:1
11 10000 11 3000 Max. 5.20 5.00 6.9:1 2.4:1
11 15000 11 3000 Max. 8.80 8.10 7.2:1 3.24:1
13-5/8 3000 13-5/8 3000 Max. 5.40 4.90 4.8:1 2.1:1
13-5/8 5000 13-5/8 3000 Max. 5.40 4.80 4.8:1 2.1:1
13-5/8 10000 13-5/8 3000 Max. 11.80 11.80 10.2:1 3.8:1
20-3/4 3000 20-3/4 3000 Max. 8.10 7.20 4.75:1 0.98:1
21-1/4 2000 21-1/4 3000 Max. 8.10 7.20 4.75:1 0.98:1
21-1/4 5000 21-1/4 3000 Max. 17.50 16.60 10.2:1 1.9:1
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons
or Size Pressure Bore Pressure to to Close Open
Type (Inches) (Max PSI) (Inches) (psi) Close Open Ratio Ratio
Hydril (continued)
Manual 11 3000 11 3000 Max. 5.50 6.00 5.6:1 4.2:1
Lock 11 5000 11 3000 Max. 5.50 5.00 5.6:1 4.2:1
Shear 11 10000 11 3000 Max. 8.80 8.20 11.7:1 4.0:1
11 15000 11 3000 Max. 8.80 8.10 7.2:1 3.24:1
13-5/8 3000 13-5/8 3000 Max. 11.50 11.20 10.1:1 4.7:1
13-5/8 5000 13-5/8 3000 Max. 11.50 11.20 10.1:1 4.7:1
13-5/8 10000 13-5/8 3000 Max. 11.80 11.80 10.2:1 3.8:1
20-3/4 3000 20-3/4 3000 Max. 17.20 16.30 10.14:1 2.2:1
21-1/4 2000 21-1/4 3000 Max. 17.20 16.30 10.14:1 2.2:1
21-1/4 5000 21-1/4 3000 Max. 17.50 16.60 10.2:1 1.9:1
MPL 7-1/16 3000 7-1/16 3000 Max. 1.20 0.93 5.4:1 1.5:1
Pipe 7-1/16 5000 7-1/16 3000 Max. 1.20 0.93 5.4:1 1.5:1
7-1/16 10000 7-1/16 3000 Max. 2.00 1.80 8.2:1 1.7:1
7-1/16 15000 7-1/16 3000 Max. 3.90 3.40 7.6:1 6.6:1
11 10000 11 3000 Max. 5.70 5.00 7.6:1 2.4:1
11 15000 11 3000 Max. 9.30 8.10 7.6:1 3.24:1
13-5/8 3000 13-5/8 3000 Max. 5.90 4.90 5.2:1 2.1:1
13-5/8 5000 13-5/8 3000 Max. 5.90 5.20 5.2:1 2.1:1
13-5/8 10000 13-5/8 3000 Max. 12.90 11.80 10.6:1 3.8:1
13-5/8 15000 13-5/8 3000 Max. 12.60 11.00 7.74:1 3.56:1
16-3/4 10000 16-3/4 3000 Max. 15.60 14.10 10.6:1 2.41:1
18-3/4 10000 18-3/4 3000 Max. 17.10 15.60 10.6:1
1.9:1
18-3/4 15000 18-3/4 3000 Max. 19.40 16.70 7.27:1 2.15:1
20-3/4 3000 20-3/4 3000 Max. 18.00 16.30 10.6:1 0.98:1
21-1/4 2000 21-1/4 3000 Max. 18.00 16.30 10.6:1 0.98:1
21-1/4 5000 21-1/4 3000 Max. 19.30 16.60 10.6:1 1.9:1
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons
or Size Pressure Bore Pressure to to Close Open
Type (Inches) (Max PSI) (Inches) (psi) Close Open Ratio Ratio
Bowen Tools, Inc.
51922 2-1/2 Sgl 5000 2-1/2 1000 0.17 0.14 7.9:1
51923 2-1/2 Sgl 10000 2-1/2 1600 0.26 0.18 7.9:1
51924 2-1/2 Twin 5000 2-1/2 900 0.35 0.27 7.9:1
60701 2-1/2 Twin 10000 2-1/2 1600 0.52 0.36 7.9:1
50460 2-9/16 Sgl 15000 2-9/16 1200 0.30 0.30 8.18:1
70051 2-9/16 Sgl 20000 2-9/16 800 0.87 0.93 23.8:1
51926 3 Sgl 5000 3 600 0.27 0.22 13.2:1
51927 3 Sgl 10000 3 1200 0.27 0.22 13.2:1
51928 3 Twin 5000 3 600 0.53 0.43 13.2:1
51929 3 Twin 10000 3 1200 0.53 0.43 13.2:1
61040 4 Sgl 5000 4 500 0.93 0.78 15.3:1
61044 4 Sgl 10000 4 1000 0.93 0.78 15.3:1
61048 4 Twin 5000 4 500 1.86 1.55 15.3:1
61050 4 Twin 10000 4 1000 1.86 1.55 15.3:1
47034 4-1/16 Sgl 10000 4-1/16 1000 0.43 0.34 13.6:1
60467 4-1/16 Sgl 15000 4-1/16 1250 0.69 0.74 16.2:1
70630 4-1/16 Twin 15000 4-1/16 1250 1.38 1.48 16.2:1
61053 4 1/2 Sgl 3000 4 1/2 400 0.90 0.81 15.3:1
66174 4 1/2 Sgl 5000 4 1/2 555 1.83 1.64 15.3:1
61055 4 1/2 Sgl 10000 4 1/2 1000 0.90 0.81 15.3:1
61507 4 1/2 Twin 5000 4 1/2 500 1.79 1.61 15.3:1
61060 4 1/2 Twin 10000 4 1/2 1000 1.79 1.61 15.3:1
51938 5-1/2 Sgl 3000 5-1/2 300 1.23 1.05 20.8:1
63642 7-1/16 Sgl 10000 7-1/16 900 1.02 1.10 16.2:1
70466 7-1/16 Twin 10000 7-1/16 900 2.04 2.20 16.2:1
60615 7-5/8 Sgl 5000 6-1/2 900 1.75 1.74 10.9:1
70399 7-5/8 Twin 5000 6-1/2 1800 3.50 3.48 10.9:1
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons
or Size Pressure Bore Pressure to to Close Open
Type (Inches) (Max PSI) (Inches) (psi) Close Open Ratio Ratio
Cameron Iron Works (continued)
U 13-5/8 10000 13-5/8 1500/5000 5.54 5.42 7.0:1 2.3:1
U-Shear 13-5/8 10000 13-5/8 1500/5000 6.78 6.36 7.0:1 2.2:1
U 13-5/8 15000 13-5/8 1500/5000 11.70 11.28 6.6:1 8.9:1
U 16-3/4 3000 16-3/4 1500/5000 10.16 9.45 6.8:1 2.3:1
U 16-3/4 5000 16-3/4 1500/5000 10.16 9.45 6.8:1 2.3:1
U-Shear 16-3/4 5000 16-3/4 1500/5000 12.03 11.19 6.8:1 1.9:1
U 18-3/4 10000 18-3/4 1500/5000 21.20 23.10 7.4:1 3.7:1
U 20 3000 20-3/4 1500/5000 8.40 7.90 7.0:1 1.3:1
U-Shear 20 3000 20-3/4 1500/5000 9.35 8.77 7.0:1 1.2:1
U 21-1/4 2000 21-1/4 1500/5000 8.40 7.90 7.0:1 1.3:1
U-Shear 21-1/4 2000 21-1/4 1500/5000 9.35 8.77 7.0:1 1.2:1
U 21-1/4 7500 21-1/4 1500/5000 20.41 17.78 5.5:1 3.0:1
U-Shear 21-1/4 7500 21-1/4 1500/5000 23.19 20.20 6.5:1 2.3:1
U 21-1/4 10000 21-1/4 1500/5000 26.54 24.14 7.2:1 4.1:1
U-Shear 21-1/4 10000 21-1/4 1500/5000 30.15 27.42 7.2:1 3.1:1
U 26 2000 26-3/4 1500/5000 10.50 9.84 7.0:1 1.0:1
U 26 3000 26-3/4 1500/5000 10.50 9.84 7.0:1 1.0:1
U-Blind 13-5/8 5000 13-5/8 1500/2500 11.60 10.90 14.0:1 2.3:1
with 13-5/8 10000 13-5/8 1500/2500 11.60 10.90 14.0:1 2.3:1
Shear 16-3/4 3000 16-3/4 1500/2500 10.80 11.70 9.0:1 1.4:1
Booster 16-3/4 5000 16-3/4 1500/2500 10.80 11.70 9.0:1 1.4:1
20 2000 20-3/4 1500/2500 16.80 15.70 14.0:1 1.2:1
20 3000 20-3/4 1500/2500 16.80 15.70 14.0:1 1.2:1
U II 18-3/4 10000 18-3/4 24.70 22.30 6.7:1 2.5:1
U II 18-3/4 15000 18-3/4 34.70 32.30 9.3:1 3.5:1
QRC 6 3000 7-1/16 1500/3000 0.81 0.95 7.75:1 1.5:1
QRC 6 5000 7-1/16 1500/3000 0.81 0.95 7.75:1 1.5:1
QRC 8 3000 9 1500/3000 2.36 2.70 9.05:1 1.83:1
QRC 8 5000 9 1500/3000 2.36 2.70 9.05:1 1.83:1
QRC 10 3000 11 1500/3000 2.77 3.18 9.05:1 1.21:1
QRC 10 5000 11 1500/3000 2.77 3.18 9.05:1 1.21:1
QRC 12 3000 13-5/8 1500/3000 4.42 5.10 8.64:1 1.07:1
QRC 16 2000 16-3/4 1500/3000 6.00 7.05 8.64:1 .62:1
QRC 18 2000 17-3/4 1500/3000 6.00 7.05 8.64:1 .62:1
QRC 20 2000 17-3/4 1500/3000 6.00 7.05 8.64:1 .62:1
SS 6 3000 7-1/16 1500/3000 0.80 0.70 3.8:1 1.0:1
SS 6 5000 7-1/16 1500/3000 0.80 0.70 3.8:1 1.0:1
SS 8 3000 9 1500/3000 1.50 1.30 3.9:1 1.0:1
SS 8 5000 9 1500/3000 1.50 1.30 3.9:1 1.0:1
SS 10 3000 11 1500/3000 1.50 1.30 3.9:1 1.0:1
SS 10 5000 11 1500/3000 1.50 1.30 3.9:1 1.0:1
SS 12 3000 13-5/8 1500/3000 2.90 2.50 3.7:1 1.0:1
SS 14 5000 13-5/8 1500/3000 2.90 2.50 3.7:1 1.0:1
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons
or Size Pressure Bore Pressure to to Close Open
Type (Inches) (Max PSI) (Inches) (psi) Close Open Ratio Ratio
Cameron Iron Works (continued)
Type F 6 3000 7-1/16 500/1500 1.50 2.30 4.5:1
with 6 5000 7-1/16 500/1500 1.50 2.30 4.5:1
Type W2 7 10000 7-1/16 500/1500 1.50 2.30 4.5:1
Operator 7 15000 7-1/16 500/1500 1.50 2.30 4.5:1
8 3000 9 500/1500 2.80 3.70 2.5:1
8 5000 9 500/1500 2.80 3.70 2.5:1
10 3000 11 500/1500 2.80 3.70 2.5:1
10 5000 11 500/1500 2.80 3.70 2.5:1
11 10000 11 500/1500 2.80 3.70 2.5:1
12 3000 13-5/8 500/1500 4.10 5.30 2.0:1
14 5000 13-5/8 500/1500 4.10 5.30 2.0:1
16 2000 16-3/4 500/1500 5.00 6.00 2.0:1
16 3000 16-3/4 500/1500 5.00 6.00 2.0:1
20 2000 20-1/4 500/1500 5.00 6.00 2.0:1
20 3000 20-1/4 500/1500 5.00 6.00 2.0:1
Type F 6 3000 7-1/16 500/1500 2.30 3.05 4.5:1
with 6 5000 7-1/16 500/1500 2.30 3.50 4.5:1
Type W 7 10000 7-1/16 500/1500 2.30 3.50 4.5:1
Operator 7 15000 7-1/16 500/1500 2.30 3.50 4.5:1
8 3000 9 500/1500 3.70 4.60 2.5:1
8 5000 9 500/1500 3.70 4.60 2.5:1
10 3000 11 500/1500 3.70 4.60 2.5:1
10 5000 11 500/1500 3.70 4.60 2.5:1
11 10000 11 500/1500 3.70 4.60 2.5:1
12 3000 13-5/8 500/1500 6.80 8.10 2.0:1
14 5000 13-5/8 500/1500 6.80 8.10 2.0:1
16 2000 16-3/4 500/1500 7.60 9.10 2.0:1
16 3000 16-3/4 500/1500 7.60 9.10 2.0:1
20 2000 20-1/4 500/1500 7.60 9.10 2.0:1
20 3000 20-1/4 500/1500 7.60 9.10 2.0:1
Type F 6 3000 7-1/16 250/1500 3.97 3.46 4.9:1
with 6 5000 7-1/16 250/1500 3.97 3.46 4.9:1
Type L 7 10000 7-1/16 250/1500 3.97 3.46 4.9:1
Operator 7 15000 7-1/16 250/1500 3.97 3.46 4.9:1
8 3000 9 250/1500 6.85 6.19 3.44:1
8 5000 9 250/1500 6.85 6.19 3.44:1
10 3000 11 250/1500 6.85 6.19 3.44:1
10 5000 11 250/1500 6.85 6.19 3.44:1
11 10000 11 250/1500 6.85 6.19 3.44:1
12 3000 13-5/8 250/1500 10.30 9.38 2.3:1
14 5000 13-5/8 250/1500 10.30 9.38 2.3:1
16 2000 16-3/4 250/1500 11.71 10.66 2.3:1
16 3000 16-3/4 250/1500 11.71 10.66 2.3:1
20 2000 20-1/4 250/1500 11.71 10.66 2.3:1
20 3000 20-1/4 250/1500 11.71 10.66 2.3:1
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons
or Size Pressure Bore Pressure to to Close Open
Type (Inches) (Max PSI) (Inches) (psi) Close Open Ratio Ratio
Type F 6 3000 7-1/16 1000/5000 0.52 1.50 1.5:1
with 6 5000 7-1/16 1000/5000 0.52 1.50 1.5:1
Type H 7 10000 7-1/16 1000/5000 0.52 1.50 1.5:1
Operator 7 15000 7-1/16 1000/5000 0.52 1.50 1.5:1
8 3000 9 1000/5000 0.90 1.80 1.0:1
8 5000 9 1000/5000 0.90 1.80 1.0:1
10 3000 11 1000/5000 0.90 1.80 1.0:1
10 5000 11 1000/5000 0.90 1.80 1.0:1
11 10000 11 1000/5000 0.90 1.80 1.0:1
12 3000 13-5/8 1000/5000 1.52 2.70 2.3:1
14 5000 13-5/8 1000/5000 1.52 2.70 2.3:1
16 2000 16-3/4 1000/5000 1.73 3.08 2.3:1
16 3000 16-3/4 1000/5000 1.73 3.08 2.3:1
20 2000 20-1/4 1000/5000 1.73 3.08 2.3:1
20 3000 20-1/4 1000/5000 1.73 3.08 2.3:1
Shaffer
LWS w/ 4-1/16 10000 4-1/16 1500/3000 0.59 0.52 8.45:1 4.74:1
Manual 6 5000 6 1500/3000 1.19 0.99 4.45:1 1.82:1
Lock 7-1/16 10000 7-1/16 1500/3000 6.35 5.89 10.63:1 19.4:1
7-1/16 15000 7-1/16 1500/3000 6.35 5.89 10.63:1 19.4:1
8 5000 8 1500/3000 2.58 2.27 5.57:1 3.00:1
10 3000 10 1500/3000 1.74 1.45 4.45:1
1.16:1
10 5000 10 1500/3000 2.98 2.62 5.57:1 2.09:1
11 10000 11 1500/3000 8.23 7.00 7.11:1 3.44:1
12 3000 12 1500/3000 4.35 5.30 8.16:1 1.74:1
13-5/8 5000 13-5/8 1500/3000 4.35 5.30 8.16:1 1.74:1
13-5/8 10000 13-5/8 1500/3000 11.56 10.52 10.85:1 3.48:1
16-3/4 5000 16-3/4 1500/3000 13.97 12.71 10.85:1 3.61:1
20 2000 21-1/4 1500/3000 5.07 4.46 5.57:1 .78:1
20 3000 21-1/4 1500/3000 5.07 4.46 5.57:1 .78:1
LWP 6 3000 7-1/16 1500/3000 0.55 0.51 —— ——
Series 8 3000 9 1500/3000 7.80 6.86 —— ——
LWP 6 3000 7-1/16 1500/3000 0.55 0.51 4.0:1 2.50:1
Type 8 3000 9 1500/3000 0.77 0.68 4.0:1 1.81:1
SL and 11 10000 11 1500/3000 8.23 7.00 7.11:1 3.44:1
LWS 13-5/8 5000 13-5/8 1500/3000 4.35 5.30 8.16:1 1.74:1
Posilock 13-5/8 5000 13-5/8 1500/3000 11.56 10.52 10.85:1 3.48:1
13-5/8 10000 13-5/8 1500/3000 10.58 10.52 7.11:1 3.48:1
13-5/8 15000 13-5/8 1500/3000 11.56 10.52 7.11:1 2.14:1
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons
or Size Pressure Bore Pressure to to Close Open
Type (Inches) (Max PSI) (Inches) (psi) Close Open Ratio Ratio
Shaffer (continued)
LWP 16-3/4 5000 16-3/4 1500/3000 13.97 12.60 11.85:1 2.45:1
Type 16-3/4 10000 16-3/4 1500/3000 14.47 12.50 7.11:1 2.06:1
SL and 18 3/4 10000 18 3/4 1500/3000 15.30 13.21 7.11:1 1.83:1
LWS 18-3/4 15000 18-3/4 1500/3000 14.62 13.33
Posilock 20 2000 21-1/4 1500/3000 7.80 6.86 8.16:1 1.15:1
20 2000 21-1/4 1500/3000 16.88 15.35 10.85:1 2.52:1
20 3000 21-1/4 1500/3000 7.80 6.86 8.16:1 1.15:1
20 3000 21-1/4 1500/3000 16.88 15.35 10.85:1 2.52:1
21-1/4 10000 21-1/4 1500/3000 16.05 13.86 7.11:1 1.63:1
Sentinel 6 3000 7-1/16 1500/3000 0.29 0.28 —— ——
Type 6 3000 7-1/16 1500/3000 2.75 2.30 6.0:1 2.57:1
B and E 6 5000 7-1/16 1500/3000 2.75 2.30 6.0:1 2.57:1
8 3000 9 1500/3000 2.75 2.30 6.0:1 1.89:1
8 5000 9 1500/3000 2.75 2.30 6.0:1 1.89:1
10 3000 11 1500/3000 3.25 2.70 6.0:1 1.51:1
10 5000 11 1500/3000 3.25 2.70 6.0:1 1.35:1
12 3000 13-5/8 1500/3000 3.55 2.90 6.0:1 1.14:1
14 5000 13-5/8 1500/3000 3.55 2.90 6.0:1 1.14:1
16 2000 15-1/2 1500/3000 3.65 3.00 6.0:1 1.05:1
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons Secondary
or Size Pressure Bore Pressure to to Volume
Type (Inches) (Max PSI) (Inches) (psi) Close Open (Gallons)
Cameron Iron Works
A 6 5000 7-1/16 1500 2.20 1.90
A 6 10000 7-1/16 1500 4.00 3.10
A 6 15000 7-1/16 N.A. N.A. N.A.
A 11 5000 11 1500 7.80 6.50
A 11 10000 11 1500 12.10 10.50
A 11 15000 11 N.A. N.A. N.A.
A 13-5/8 5000 13-5/8 1500 15.50 13.90
A 13-5/8 10000 13-5/8 1500 21.50 18.70
A 16-3/4 5000 16-3/4 1500 33.00 29.00
D 6 5000 7-1/16 3000 1.69 1.39
D 7-1/16 10000 7-1/16 3000 2.94 2.55
D 10 5000 11 3000 5.65 4.69
D 11 10000 11 3000 10.15 9.06
D 13-5/8 5000 13-5/8 3000 12.12 10.34
D 13-5/8 10000 13-5/8 3000 18.10 16.15
Shaffer
Spherical 6 3000 7-1/16 1500 4.57 3.21
BOP 6 5000 7-1/16 1500 4.57 3.21
7-1/16 10000 7-1/16 1500 17.11 13.95
8 3000 9 1500 7.23 5.03
8 5000 9 1500 11.05 8.72
10 3000 11 1500 11.00 6.78
10 5000 11 1500 18.67 14.59
11 10000 11 1500 30.58 24.67
12 3000 13-5/8 1500 23.50 14.67
13-5/8 5000 13-5/8 1500 23.58 17.41
13-5/8 10000 13-5/8 1500 40.16 32.64
16-3/4 5000 16-3/4 1500 33.26 25.61
18 3/4 5000 18 3/4 1500 48.16 37.61
20 2000 21-1/4 1500 32.59 16.92
21-1/4 5000 21-1/4 1500 61.37 47.76
Regan
K 3 3000 3 3000 0.50
K 4 3000 4 3000 0.80
K 7 3000 6 1/4 3000 1.60
K 8 5/8 3000 7 7/8 3000 4.10
K 9 5/8 3000 8 7/8 3000 5.70
K 10 3/4 3000 10 3000 7.60
K 11 3/4 (old) 3000 10 7/8 3000 11.10
K 11 3/4 (new) 3000 11 1/8 3000 10.30
K 13 3/8 3000 12 3/8 3000 15.30
K 13 3/4 3000 13 3/4 3000 19.90
Hydraulic
Model Nominal Working Vertical Operating Gallons Gallons Secondary
or Size Pressure Bore Pressure to to Volume
Type (Inches) (Max PSI) (Inches) (psi) Close Open (Gallons)
Regan (continued)
K 16 3000 15 3/8 3000 25.00
K 18 5/8 3000 17 1/2 3000 29.50
KFD 16 500 10 1000 3.00
KFD 18 3/4 500 10 1000 3.00
KFD 20 500 10 1000 3.00
KFD 22 500 10 1000 3.00
KFD 24 500 10 1000 3.00
KFDJ 27 1/2 2000 10 2500 3.00
KFL 13-5/8 3000 13-5/8 Well + 500 19.50
KFL 13-5/8 5000 13-5/8 Well + 500 22.00
KFL 13-5/8 10000 13-5/8 Well + 500 24.50
KFL 16-3/4 3000 16-3/4 Well + 500 25.75
KFL 16-3/4 5000 16-3/4 Well + 500 29.00
KFL 16-3/4 10000 16-3/4 Well + 500 31.50
KFL 20 2000 20-3/4 Well + 500 28.50
KFL 20 3000 20-3/4 Well + 500 32.00
KFL 20 5000 20-3/4 Well + 500 35.00
KFL 30 1000 28 Well + 500 47.50
KFL 30 2000 28 Well + 500 52.00
KFL 30 1000 26-1/2 Well + 500 51.50
KFL 30 2000 26-1/2 Well + 500 56.00
Torus 6 3000 7-1/16 3000 4.50
Torus 6 6000 7-1/16 3000 4.50
Torus 8 3000 9 3000 8.25
Torus 8 6000 9 3000 8.25
Hydraulic
Model Line Working Bore Operating Gallons Gallons
or Size Pressure Size Pressure to to
Type (Inches) (Max PSI) (Inches) (psi) Close Open
Cameron Iron Works
HCR 4 3000 4 1500 0.52 0.61
HCR 4 5000 4 1500 0.52 0.61
HCR 6 3000 7 1500 1.95 2.25
HCR 6 5000 7 1500 1.95 2.25
F 2 960-3000 1 13/16 1500/5000 0.10 0.10
F 2 5000-15000 1 13/16 1500/5000 0.16 0.16
F 2 960-3000 2-1/16 1500/5000 0.10 0.10
F 2 5000-15000 2-1/16 1500/5000 0.16 0.16
F 2-1/2 960-3000 2-9/16 1500/5000 0.13 0.13
F 2-1/2 5000-15000 2-9/16 1500/5000 0.20 0.20
F 2-1/2 960-3000 2-9/16 1500/5000 0.20 0.20
F 2-1/2 15000 2-9/16 1500/5000 0.40 0.40
F 3 960-2000 3-1/8 1500/5000 0.15 0.15
F 3 3000-5000 3-1/8 1500/5000 0.24 0.24
F 3 10000 3-1/8 1500/5000 0.28 0.28
F 3 15000 3-1/8 1500/5000 0.49 0.49
F 4 2000-5000 4-1/8 1500/5000 0.30 0.30
F 4 10000 4-1/8 1500/5000 0.59 0.59
F 6 2000-5000 6-1/8 1500/5000 0.84 0.84
DV 4 3000 4 1500 1.10 0.80
DV 4 5000 4 1500 1.10 0.80
DV 6 3000 7 1500 3.60 2.10
DV 8 3000 9 1500 5.60 2.40
DV 10 3000 11 1500 11.40 5.70
DV 10 5000 11 1500 11.40 5.70
DV 12 3000 13-5/8 1500 22.70 11.80
Hydraulic
Model Line Working Bore Operating Gallons Gallons
or Size Pressure Size Pressure to to
Type (Inches) (Max PSI) (Inches) (psi) Close Open
McEvoy Oil Field Equipment (continued)
AC Valve 3 5000 2500 0.46 0.51
w/ U-1 4 2000 2500 0.62 0.69
Hyd. 4 3000 2500 0.62 0.69
Oper. 4 5000 2500 0.98 1.04
C Valve 2 5000 2-1/16 1500 0.10 0.11
with 2-1/2 5000 2-9/16 1500 0.12 0.13
RM-1 3 5000 3-1/8 1500 0.23 0.25
Actuator 4 5000 4-1/8 1500 0.44 0.50
E Valve 1-13/16 10000 1-13/16 1500 0.08 0.09
with 2-1/16 10000 2-1/16 1500 0.16 0.18
RM-1 2-9/16 10000 2-9/16 1500 0.30 0.33
Actuator 3-1/16 10000 3-1/16 1500 0.36 0.37
4-1/16 10000 4-1/16 1500 1.00 1.07
EDU and 3 5000 3-1/16 2500 0.47 0.52
EU Valve 3-1/16 10000 3-1/16 2500 0.47 0.52
with U-1
Actuator
Shaffer
Flo-Seal 2 Reg. 2000 1-11/16 3000 0.20 0.20
2 2000 2-1/16 3000 0.20 0.20
2 Reg. 3000 1-11/16 3000 0.20 0.20
2 3000 2-1/16 3000 0.20 0.20
2 Reg. 5000 1-11/16 3000 0.20 0.20
2 5000 2-1/16 3000 0.20 0.20
2-1/16 10000 2-1/16 3000 0.40 0.40
2-1/16 15000 2-1/16 3000 0.40 0.40
2-1/2 2000 2-9/16 3000 0.30 0.30
2-1/2 3000 2-9/16 3000 0.30 0.30
2-1/2 5000 2-9/16 3000 0.30 0.30
3 2000 3-1/8 3000 0.30 0.30
3 3000 3-1/8 3000 0.30 0.30
3 5000 3-1/8 3000 0.30 0.30
3-1/16 10000 3-1/16 3000 0.60 0.60
4 3000 4-1/16 3000 0.80 0.80
4 5000 4-1/16 3000 0.80 0.80
4-1/16 10000 4-1/16 3000 1.30 1.30
6 3000 7-1/16 3000
Hydraulic
Model Line Working Bore Operating Gallons Gallons
or Size Pressure Size Pressure to to
Type (Inches) (Max PSI) (Inches) (psi) Close Open
Shaffer (continued)
Flo-Seal 2 Reg. 2000 1-11/16 3000 0.30 0.30
with 2 2000 2-1/16 3000 0.30 0.30
Ramlock 2 Reg. 3000 1-11/16 3000 0.30 0.30
2 3000 2-1/16 3000 0.30 0.30
2 Reg. 5000 1-11/16 3000 0.30 0.30
2 5000 2-1/16 3000 0.30 0.30
2-1/16 10000 2-1/16 3000 0.40 0.40
2-1/16 15000 2-1/16 3000 0.40 0.40
2-1/2 2000 2-9/16 3000 0.30 0.30
2-1/2 3000 2-9/16 3000 0.30 0.30
2-1/2 5000 2-9/16 3000 0.30 0.30
3 2000 3-1/8 3000 0.40 0.40
3 3000 3-1/8 3000 0.40 0.40
3 5000 3-1/8 3000 0.40 0.40
3-1/16 10000 3-1/16 3000 0.60 0.60
4 3000 4-1/16 3000 0.80 0.80
4 5000 4-1/16 3000 0.80 0.80
4-1/16 10000 4-1/16 3000 0.80 0.80
6 3000 7-1/16 3000
CB 3 5000 3-1/8 3000 0.00 0.45
Subsea 3-1/16 10000 3-1/16 3000 0.00 0.50
Failsafe
Long
Sea
Chest
CB 3 5000 3-1/8 3000 0.43 0.45
Subsea 3-1/16 10000 3-1/16 3000 0.45 0.50
Failsafe
Short
Sea
Chest
Type DB 3 3000 3-1/8 3000 0.30 0.30
3 5000 3-1/8 3000 0.30 0.30
3-1/16 10000 3-1/16 3000 0.60 0.60
4 3000 4-1/16 3000 0.80 0.80
4 5000 4-1/16 3000 0.80 0.80
4-1/16 10000 4-1/16 3000 1.30 1.30
6 3000 7-1/16 3000 2.00 2.00