Professional Documents
Culture Documents
I - BASEMENT LOADS
Computing load Unit Standard load Unit
Safety factor n = 1.15
Design
N = 692.17 kN Nstandard = 612.68 kN Vertical forces include Pile cap
MxDesign = 14.48 kN.m Mxstandard = 11.54 kN.m
Design standard
My = 10.12 kN.m My = 8.87 kN.m
Design standard
Qx = 18.02 kN Qx = 15.81 kN
QyDesign = 12.66 kN Qystandard = 11.92 kN
II - GEOLOGICAL CBH22
(degr) (degr) (degr) (kN/m3) đn(kN/m3) ctc(kN/m2) c1(kN/m2) c2(kN/m2) h(m)
Layer G Fine sand
0.00 0.00 0.00 18.00 8.00 0.00 0.00 0.00 0.50
Layer 1 Very silty sand to silty sand, medium dense to dense
29.63 29.63 29.63 20.10 10.10 13.60 13.60 13.60 21.50
Layer 1A Slightly sandy silt/Very silty sand with seashell, loose to medium dense
14.90 14.90 14.90 18.47 8.47 23.76 23.76 23.76 10.00
- Underground water level 2.00 m
III. PILE SPECIFICATIONS
1. Select the Material of Piles
- Concrete 1x2 with grade C80
- Type of reinforcement Cable
2. Select the cross section of Piles
- Diameter of designing pile PHC-D350 mm
2
+ The area of cross section: Fpile = 962.1 cm
+ Perimeter of pile: Upile= 110.0 cm
- The length of working pile: Lpile = 11.00 m
3. Reinforcement:
- The number of bearing steel bar 7.1
- The area of steel bar: Fa = 2.77 cm2
4. Load calculation of Piles with Material
- Load capacity pressed pile materials by supplier.
5. Designing load capacity
- Designing load capacity: Pdesign = 1200 kN
IV. DEPTH AND HEIGHT OF FOUNDATION FRAMEWORK
1. Depth of foundation framework:
- Buring foundation depth H= 0.900 m
2. Height of foundation framework (Check again after arranging completely piles)
HPile cap= 1.15 m
3. Eccentricity between axial force N and center of foundation framework:
- Moment value Mx = 14.483 kN.m
- Moment value My = 10.119 kN.m
- Eccentricity between column and center of foundation framework y = 0.000 m
- Eccentricity between column and center of foundation framework x = 0.000 m
- Eccentricity ex = 0.024 m
- Eccentricity ey = 0.017 m
CALCULATION ON PILE RAFT PC1 (850x850x1150) - 1 PILES PHC-D350
Ntt Mx y My x
Pmin Pdesignmin = 692.17 kN/Pile
nc yi2 xi2
Pdesignaverage = 692.17 kN/Pile
design
Check P max <= 1.2Pdesign 692.17 1440.00 Ok
Pdesignmin > 0 692.17 0.00 Ok
VIII. STRUCTURE OF FOUNDATION (PILE LENGTH 11 M)
P average = 29.63 Degree
đn
- Average weight of soil layers in pile body average = 12.02 kN/m2
1. Size of the conventional foundation block
- Length of the conventional foundation block Lconvention= 3.21 m
- Width of the conventional foundation block Bconvention= 3.21 m
- Area of the conventional foundation block Fconvention= 10.31 m2
- Volume of foundation framework + piles WFR+pile= 4.21 kN
- Volume of the soil occupied by piles + foundation
Wpile+found= 21.11 kN
framework
- Volume of the conventional foundation Wconvention= 1529.14 kN
2. Standard moment at center of the conventional foundation:
Mstandardx = 146.35 kN.m
CALCULATION ON PILE RAFT PC1 (850x850x1150) - 1 PILES PHC-D350
Stress (kN/m2)
0.0
‐320 ‐290 ‐260 ‐230 ‐200 ‐170 ‐140 ‐110 ‐80 ‐50 ‐20 10 40 70 100 130 160 190 220 250 280
‐1.0
‐2.0
CALCULATION ON PILE RAFT PC1 (850x850x1150) - 1 PILES PHC-D350
‐3.0
‐4.0
‐5.0
Axis
‐6.0
Depth (m)
Selfweight stress
‐7.0 Settlement stress
‐8.0 Depth of settlement stopped
‐9.0
‐10.0
‐11.0
‐12.0
‐13.0
‐14.0
‐15.0
BOTTOM OF CONVENTIONAL FOUNDATION STRESS CHART