Professional Documents
Culture Documents
APPR. BY
REV DATE REVISION DESCRIPTION PRPD. BY CHKD. BY APPR. BY
CLIENT
1) Geometry
Safety Wall
A A
Plan View
Concrete Pedestal
1m
Concrete Footing
Section A-A
3) Loading on Pedestal
Design Forces
Vertically Downward Weight = 42.18 kN
Moment on Pedestal = 1.23 kN-m
Shear Force = 0.82 kN
Design of Pedestal
Design moment Mz = 1.232 kN-m
Design shear Vu = 0.822 kN
Depth : Db = 1000 mm
Reinforcement : db = 12 mm
n= 10 nos
2
Ast = 1131.0 mm
2 Material Properties:
Concrete compressive strength f'c = 25 MPa
r = Ast/bw x d = 0.0026
Mn = Rn x bw x d2 = 517.46 kN-m
f= (Flexure) 0.9
>Mu, Hence ok
3 Horizontal Reinforcement :
sqrt(fc')
Minimum steel ratio, ρmin = = 0.00250
4 fy
As,V
Actual steel ratio, ρactual = = 0.00260
bd1
# 12 @ 100 mm C/C
1000 mm
CLINET REVISION
DESIGN OF FOOTING
FACTOR = 1
DESIGN OF FOOTING FOR FOUNDATION F4
P= 42.18 kN
Mz= 1.23 kNm
Hx = 0.82 kN
Mx= 0.00 kNm
Hz = 0.00 kN
P= 42.18 kN
Mz= 1.23 kNm
Z
NGL Hx = 0.82 kN S
Hz = 0.00 kN
b Z
d
R Q
B
B
Design Checks
The design checks for the following parametrs have been carried out and presented
i) Bearing pressure under the pad
ii) Requirement of reinforcement for the pad for flexure
iii) Check for One way and Punching shear
Basic Data
Soil Data:
Type of soil in foundation = HARD STRATA
Breadth b = 0.460 m
Length l = 1.000 m
Size of Foundation Pad
Breadth B = 0.800 m
Length L = 1.000 m
Depth of the Pad d = 0.200 m
Total depth of foundation from GL D = 1.000 m
DESIGN:
Load data:
3
Volume of foundation concrete = 0.53 m
Weight of concrete = 13.2 kN
Downward load (maximum) = 42.2 kN
Weight of soil = 5.2 kN
Total downward load W = 60.5 kN
W 6ex 6ey
Maximum Soil Pressure at Point Q "qmax" = X 1 + +
BL B L
2
= 91.1 kN/m
2
< 100 kN/m
HENCE SAFE
Design of Foundation Pad (About Z-Z)
V M
d
d/2 d/2
B
53.9 kN/m2
84.6 kN/m2
R B C D E Q
PRESSURE DISTRIBUTION DIAGRAM
Depth : Db = 1000.0 mm
Reinforcement : db = 12 mm
Spacing 200 mm
2
Ast = 565.2 mm
2 Material Properties:
f'c strength
Concrete compressive = 25 MPa
Reinforcement yieldfystrength
= 500 MPa
>Mu, Hence ok
f= (Shear) 0.8
So, provide # 12 mm @ 200 mm C/C bars for footing and #12 @ 150 mm C/C bars for slab