Professional Documents
Culture Documents
Structural labORATORY RECM PDF
Structural labORATORY RECM PDF
AIM: Experiment on a 2 hinged arch for horizontal thrust and influence line for horizontal thrust.
Theory:-
The horizontal thrust ‘H’ in the case of two hinged arch is given by:
1 1
H= 1 = 1
∫ y² ds/E1 ∫ y² dx
0 0
Where ds = dx secθ
Take the case of two hinged parabolic arch subjected to a concentrated load W at a distance of kl
from A. (fig. 1)
In the parabolic arch, rise of arch ‘y’ n at any section at a distance x from A is given by y = A x
(1-x) (considering support as origin)
VB = W k
H = 5 kl/8h (k³-2k²+l)
Apparatus:-
Procedure:-
(1) Place the 1kg load on the first hanger position, move the lever the lever into contact with a
100gm hanger on the ratio 4:1 position adjust the dia gauge to zero.
(2) Add 10kg to the 1kg hanger without shock and observe the dial reading.
(3) Restore the dial to zero reading by adding loads to the lever hanger, say the load is W.
(4) The experimental value of the influence ordinate at the first hanger position on is than
4W/10.
Precautions:-
Load position 1 2 3 4 5 6 7 8 9 10
Load (kg)
Calculated ordinate
Results:-
K= position
of wt app
Horizontal
Balancing Hanger Thrust Calculated
Sr. No. Weight Position Experiment Thrust % crror
Span of
Arch
Wa/10b
Load position 1 2 3 4 5 6 7 8 9 10
Load (kg)
Calculated ordinate
Results:-
K= position
of wt app
Horizontal
Balancing Hanger Thrust Calculated
Sr. No. Weight Position Experiment Thrust % crror
Span of
Arch
Wa/10b
Object:-
Theory:-
L1 = length of member AD
L2 = length of member CD
L3 = length of member BD
a = distance AB
b = distance BC
w = applied load W at D
U= (i)
W (N1a² – N2b²)
X
V= (ii)
A1E1 1
A3E3 1
X
where N3 = (viii)
where AE/L is the stiffness of the member and is defined as force per unit deformation
(extension). The stiffness (K), can be determined for each spring by taking out the spring and
suspending from is loads of 1kg, 3kg, 4kg and 5kg (10, 30, 40 and 50N) in succession and
measuring the extension in each case. A graph plotted between load and extension, which shall be
a straight line with in elastic limit and the values of K which is the slope of the line can be found
from this graph.
Apparatus:-
Three bar suspension system, deflection dial gauges, scale, weights etc.
Procedure:-
(a) Find out the stiffness (K) of each spring by isolation from the apparatus.
(b) Measure the distance a, b, L1, L2 and L3 with the help of a meter scale.
(c) Fix the dial gauges at point D to measure the vertical and horizontal displacements
simultaneously for each addition of vertical load.
(d) Remove the slackness of the members by putting a load of 0.5kg (5N) load at joint
D and treat the deflected position as the datum (Initialization).
(e) Note the deflections U and V and forces T1, T2 and T3 atleast for 3 sets of loads.
Precautions:-
1. 0.0
2. 1.0
3. 2.0
4. 3.0
5. 4.0
T1
T2
T3
Result:-
Compare the experimental and analytical values of T1, T2 and T3 and give your comments.
Diagram:-
Object:-
Theory:-
In structural members subjected to flexure, the Euler Bernoulli’s equation {σ/y = M/1 =
E/R} is valid only if the applied bending moment acts about one or the other principal axis of the
cross section. However a member may be subject to a bending moment which acts on a plane
inclined to the principal axis (say). This type of bending does not occur in a plane of symmetry of
the cross section, it is called unsymmetrical bending. Since the problem related to flexure in
general differs from symmetrical bending, it may be termed as skew bending.
From the principal of mechanics, any couple which may cause bending moment at a
section of a beam may be resolved in to two components. The component of the bending moment
acting around x is M cos α, while the one acting around the y-axis is M is α. The sense of each
component follows from the sense of the total moment M. These moments may be used
separately in the usual flexure formula and the compound normal stresses follow by super
position as follows:
(a) Bending Moment in a plane that is not coincident with either of the principal axes.
(b) Components of the bending moment in the plane of the principal axes.
For beams having unsymmetrical cross-section such as an angle (L) or a channel ([)
In the present experiment for a cantilever beam of an angle section, the plane of loading
is always kept vertical and the angle iron cantilever beam itself is rotated through angles in steps
of 45°.
Consider the position of the angle section as shown in Fig. (2). The plane of loading makes an
angle ф with V-V axis of the section, which is one of the principal axes of the section. The
components of the vertical load P along V-V and U-U axes are P cos ф and P sin ф respectively.
The deflections U and V along U-V and V-V axes respectively are given by
____________
Where β is the inclination of the resultant deflection with the U-U axes. This resultant
displacement is perpendicular to the neutral axis n-n (Fig. 3) but notin the plane of the load P.
In Fig. the following notation has been used:-
00’ = D
0’p = DV
0P = DU
0’Q = DX
0Q = DY
3Eluu
tan β = ς / y = 0’P/0P =
y = Psin φ. L³
3Elvv
For the angle section used in the present experiment luu and lvv can be known from the tables of
Bureau of Indian Standard hand book for properties of standard section. Therefore a given angle
ф, the magnitude of angle β can be calculated from equation (vi).
The horizontal and vertical components of the deflection can be calculated on the basis of
the geometry available as shown in Fig. 4. It can be seen.
ζ = . cos (φ + β)
> ..................(vii)
ψ = . sin (φ + β)
Similarly
Apparatus:-
Cantilever beam having an equal angle section. The beam is fixed at one end with
possibility of rotation of 45° intervals and clamped. At the free end, the loading arrangements are
such that vertical loading is always ensured, dial gauges, weights etc.
Procedure:-
(a) Clamp the beam at zero position and put a weight of 500gms (5N) on the hanger and lake
the zero loading on the beam to activate the member.
(b) Set the dial gauges to zero reading to measure vertical and horizontal displacements at the
free end of the beam.
(c) Load the beam in steps of 1kg (10N) up to 8kg (80N) and note the vertical and horizontal
deflections each time.
(d) Repeat the steps (a) to (c) turning the beam through 45° intervals. Problem of
unsymmetrical bending will arise only in those cases where the legs of the angle section
are in horizontal and vertical positions. In those cases both vertical and horizontal
deflections need be measured.
(e) Compute the theoretical deflections and compare with those measured experimentally.
Precautions:-
(1) Take care to see that you do not exert force on the free end of the cantilever beam.
(2) Put the load on the hanger gradually without any jerk.
(3) Perform the test at a location which is free from vibrations.
1. 0
2. 45°
3. 90°
4. 135°
5. 180°
6. 225°
7. 270°
8. 315°
Results:-
Aim: - To verify the Muller Breslau theorem by using Begg’s deformator set.
The application of Begg’s deformeter apparatus involves the use of the relation.
F2 = kpn (δn/δ2)
or shear component.
Procedure: -
i) Choose the problem for the study e.g. portal frame of equal / unequal legs,
beams, trusses or any other structures.
ii) Choose the scale reduction factor for the linear dimensions that will give a model of
iii) Select the material for model e.g. plastic sheet/Acrylic/Perspex or any other desired
sheet. The width and thickness should remain same throughout the length used.
iv) Cut the model in the selected shape /size .Mark the center line throughout the
model length otherwise every time one should have to find out the centre.
Observation Table: -
Object:-
Theory:-
Let the internal forces in the three rods Ad, BE, and CF be R1, R2 and R3
respectively. Lengths AD = BE = CF = L
Lengths AB = BC = DE = EF = L
I = Moment of inertia of the cross-section of the beam ABC and the beam DEF.
E = Young’s Modulus of Elasticity of the materials of the beam ABC and beam DEF.
DD1 = y1
EE1 = y2
FF1 = y3
EE2 = (y1+y3)/2
Case I
When support B exists, beam ABC becomes in-operative. The central deflection at point
Prepared By: Mr. Neeraj Mehta Page 20
E, of beam DEF, due to load – at G and force R2 at E, Relative to the deflected portions of points
D and F given by.
Let y1 and y3 be the elongations of the rods AD and CF respectively. The total deflection of points
E relative to its original positions is
Also
R1 + R2 + R3 = W ...................... (iv)
Solving eqn. (iii), (iv) and (v) simultaneously for R1, R2 and R3 we obtain
W 3K1 + K3+(11/12)L³/El
R2 =
Case 2
If the support B were not there, beam AC will also deflect due to the load R2 applied at its
centre. Here the total central deflection of point E, relative to its original positions, as given by the
expression (ii) is equal to the elongation of member BE plus the central deflection of beam ABC.
Prepared By: Mr. Neeraj Mehta Page 21
R2.L/A2E2+R2.L³/6El = ½ {R1L/A1E1 + R3L/A3E3} + (11/96)(WL³/El)
Solving equs. (iii A), (iv) and (v) for R1, R2 and R3 simultaneously.
X
R2 =
In expressions (vi and (vii) the quantity K = L/A.E for any spring (used as suspension rod here) is
the extension of the spring per Kg. (N) of weight. This may be determined for individual springs.
Procedure:-
(a) Plot graphs between load applied and extension in each spring. From the graph
determine the value of stiffness K. (extension per unit load) for each spring.
(b) Tighten the screw at top for case 1 to make the supports rigid, load the beam DEF at
quarter point and measure extensions of springs. Start with initial load of 1kg. (10N)
increments of 1kg (10N) and maximum load of 4kg (40N).
Precautions:-
(a) Increase the load on the spring gradually while finding the value of K of individual
spring.
(b) Load the lower beam without nay jerk.
(c) Measure the extensions of the springs very accurately.
Table. K = LA.E
Reading at
Sr. No.
R1 (Reaction) R2 (Reaction) R3 (Reaction)
Case-1.0 kg
2.10 N (1kg)
3.20 N (2kg)
4.30 N (3kg)
Case-1 Observed
10 N (1kg) Calculated
20 N (1kg) Observed
Calculated
30 N (1kg) Observed
Calculated
Object:-
Theory:-
Taking moments about top joint, expressions for horizontal shear at supports A and B will be
MAB + MBA – Pa
HA =
LAB
MDC + MCD
LCD
After knowing HA and HD, we can write horizontal equilibrium equation for the frame as HA +
HD + P = 0
This gives additional equation required. It is called shear equation/shear condition. Hence Q A and
QB and (Sway) can be found.
Similarly for case given below (sec. fig. ix)
MBA + MAB – Pa /L
HA =
MCD + MDC
HP =
Apparatus:-
Procedure:-
EXPERIMENT- 7
Object:-
Theory:-
Suspension bridges are used for highways, where the span of a bridge is more than 200m.
Essentially, a suspension bridge (Fig. 1) consists of the following elements.
i. The cable,
ii. Suspenders
iii. Decking, including the stiffening girder.
iv. Supporting tower
v. Anchorage
The traffic load of the decking is transferred to main cable through the suspenders. Since the
cable is the main load bearing member, the curvature of the cable of an unstiffened bridge change
as the load moves on the decking. To avoid this, the decking is stiffened by provision of either a
three hinged stiffened girder. The stiffened girder transfers a uniformly distributed or equal load
to each suspender, irrespective of the load position on the decking. The suspension cable is
supported on either side. There are two arrangements generally used. The suspension cable may
either pass over a smooth frictionless pulley and anchored to the other side, or it may be attached
to a saddle placed on rollers. In the former case the tension in the cable on the two sides of the
pulley are equal while in the latter case, the horizontal components of the tension on the two sides
are equal since the cable cannot have a movement relative to the saddle. The cable consists of the
either wire, rope, parallel wires jointed with clips or eye bar links. The cable can carry direct
tension only, and the bending moment at any point on the cable is zero. The suspenders consist of
round rods or ropes with turn buckler so that adjustment in their lengths may be done if required.
The anchorage consists of huge mass of concrete, designed to resist the tension of the cable. Let
us take the case of a cable geometry having the cable chord horizontal. (fig. ii)
Consider the equilibrium of the portion LA to left of C (Fig. iii). The left portion is in equilibrium
under three forces. (i) the cable tension T at A (i.e) the resultant of H and VA. (ii) The external
load WL/2 acting at L/4 from C, and (iii) The horizontal cable tension H at C. All these forces
must meet at a point becomes a triangle AA1E becomes a triangle of forces which.
H/A1E = T/AE = (WL/2)(1/AA1)
Hence H = WL²/8d
_________
TA = √VA² + H²
__________
TB = √VB² + H²
_________________
TA = TB = T = √(WL/2)² + (WL²/8d)²
_________
T = H √l + 16d²/L²
The inclination β of T with the vertical is given by ten β = H/V = WL²/8d.2/WL = L/4d
It should be remembered that the horizontal component of cable at any point will be equal to H.
To determine the shape of the cable under uniformly distributed load. Substituting the value of H.
Prepared By: Mr. Neeraj Mehta Page 27
(WL²8d) y = WLx/2 – Wx²/2
y = 4dx/L² (L-x)
This is thus the equation of the curve with respect to the cable chord. The cable, thus takes the
form of a parabola when subjected to uniformly distributed load of the parabola can be written,
with C as origin as follows
y = Kx²
x = L/2 and y = d
K = y/x² = d/(L/2)² =
4d/L² y = 4d/L²x²
Consider an element of length ds of the curve, having co-ordinates x and y. The total length ‘s’ of
the curve is given by
2 L/2
½
S = ∫ds = 2∫ [1 = (du/dx)²]
0 0
Apparatus: -
Procedure: -
Object: -
Theory: -
The results obtained from this experiment are used to study the behavior of concrete
subjected to prolonged loading which has special importance as the concrete is not truly elastic
material since it possesses the ability to ‘creep’ during and after the application of load. The
phenomenon has been explained in fig. (i)
The modulus of elasticity of concrete and its corresponding compressive strength are
required in the design calculations of concrete structures. In the field of Reinforced Cement
Conerte design it is extensively used in the form of modular ratio.
The modulus of elasticity can be determined by measuring the compressive strain when a
sample is subjected to a compressive stress. Indian Standards stipulate that height should be at
least twice the diameter. Two extensometers should be used to check on eccentric loading and
they should be mounted diametrical opposite.
The ultimate compressive strength of concrete shall be determined by testing three cubes
at the time when the specimen is tested for determining the modulus of elasticity.
The modulus of elasticity is taken as the slope of the chord from the origin to some
arbitrarily chosen point on the stress strain curve as shown in Fig. (ii). This is called secant
modulus. Sometimes it is taken as slops of the tangent at the origin or the slope of tangent at some
arbitrary chosen stress (called tangent modulus) but the tangent at the origin is difficult to draw
accurately.
Mixing pan, tamping bar, trowels, capping apparatus, Lamb’s extensometer with
illuminated scale and telescope, a testing machine.
Procedure: -
(1) Take mix proportion as 1:2:4 by mass and water cement ratio as 0.50. Take 28kg of
coarse aggregate, 14kg of fine aggregate and 7kg of cement and prepare the
concrete mix.
(2) Prepare three 150mm cubes and three 150x300mm cylinders.
(3) Apply a proper capping to the top of the cylinders.
(4) Cure these specimens under water for 28 days
(5) Test the three cubes in wet condition for compressive strength after 28 days of
curing and determine the average compressive strength.
(6) Mount the Lamb’s extensometer to a cylinder on its opposite sides and parallel to its
axis. The cylinders are also tested in wet condition.
(7) Load the cylinder at the rate of 14N/mm² per minute and at a regular interval of
loading (generally two tones) record the extensometer readings.
(8) Calculate the stress and strains for each cylinder and plot stress-strain curves of
concrete.
(9) Determine the modulus of elasticity (secant modulus) at 30 percent to cube strength.
Precautions: -
(1) Compacting strokes should be uniformly applied over the whole surface.
(2) The distance between the telescope and the scale should be so adjusted that a well
defined image of the scale is obtained.
(3) The specimen for determining the modulus of elasticity should be loaded and
unloaded three times to the stress of one third of ultimate strength.
(4) The compressive strain shall be read at intervals during second and third loading
and if they differ by more than 5 percent. The loading should be repeated until
strains of successive cycles do fall within limit.
(5) Two extensometers should be used to check on eccentric loading.