Professional Documents
Culture Documents
Products by Symantec ®
Hardware TechNote
Symantec, the Symantec logo, and Veritas by Symantec are trademarks or registered
trademarks of Symantec Corporation or its affiliates in the U.S. and other countries. Other
names may be trademarks of their respective owners.
The product described in this document is distributed under licenses restricting its use,
copying, distribution, and decompilation/reverse engineering. No part of this document
may be reproduced in any form by any means without prior written authorization of
Symantec Corporation and its licensors, if any.
Symantec Corporation
20330 Stevens Creek Blvd.
Cupertino, CA 95014
www.symantec.com
Technical support
For technical assistance, visit http://support.veritas.com and select phone or
email support. Use the Knowledge Base search feature to access resources such
as TechNotes, product alerts, software downloads, hardware compatibility lists,
and our customer email notification service.
Contents
Chapter 1
Disk Storage Arrays .............................................................................................................................. 7
Supported products .................................................................................................................................. 7
Supported Technologies .......................................................................................................................... 7
Array settings........................................................................................................................................... 8
Failover modes..................................................................................................................................... 8
EMC arrays .............................................................................................................................................. 9
EMC CLARiiON arrays ...................................................................................................................... 9
DMP and EMC Symmetrix disk array support.................................................................................... 9
EMC Symmetrix DMX arrays........................................................................................................... 10
Hitachi Data Systems (HDS) arrays ...................................................................................................... 11
HDS AMS/WMS arrays .................................................................................................................... 11
HDS TagmaStore USP/NSC and USP V/VM arrays ........................................................................ 12
HDS AMS2300 Series ....................................................................................................................... 12
HDS Thunder 9500V arrays .............................................................................................................. 13
HDS Lightning 9970V/9980V arrays ................................................................................................ 14
HP arrays................................................................................................................................................ 15
HP StorageWorks EVA3000/5000 arrays ......................................................................................... 15
HP StorageWorks EVA4000/6000/8000 arrays ................................................................................ 15
HP StorageWorks XP128/1024 arrays .............................................................................................. 16
HP StorageWorks XP10000/12000/20000/24000 arrays .................................................................. 16
IBM arrays ............................................................................................................................................. 17
IBM Enterprise Storage System ESS arrays...................................................................................... 17
IBM TotalStorage DS4xxx/DS5xxx arrays ....................................................................................... 17
IBM TotalStorage DS6000 arrays ..................................................................................................... 18
IBM TotalStorage DS8000 arrays & XIV ......................................................................................... 18
IBM SVC arrays ................................................................................................................................ 19
Sun arrays .............................................................................................................................................. 20
Sun StorEdge 2510/2530/2540 .......................................................................................................... 20
Sun StorEdge 6320 (T4) .................................................................................................................... 21
Using the Sun StorEdge T4 array with Veritas Storage Foundation ................................................. 21
Sun StorageTek 9970/9980 arrays..................................................................................................... 22
Sun StorageTek 9985V/9990V arrays ............................................................................................... 22
SUN StorageTek 6130/6140/6540/.................................................................................................... 22
SUN StorageTek 6580/6780.............................................................................................................. 23
Huawei Symantec arrays ....................................................................................................................... 24
Oceanspace S5300/S5500/S5600/S6800E arrays.............................................................................. 24
Oceanspace S2300/S2300E arrays..................................................................................................... 25
Oceanspace S2600F/S2600C arrays .................................................................................................. 25
Oceanspace VIS6300/VIS6600 arrays............................................................................................... 26
Fujitsu arrays.......................................................................................................................................... 27
ETERNUS DX60, ETERNUS DX80 arrays ..................................................................................... 27
ETERNUS2000 arrays....................................................................................................................... 28
ETERNUS8000Model800/1200/2200, ETERNUS4000Model400/600 arrays ................................ 28
ETERNUS8000Model700/900/1100/2100, ETERNUS4000Model300/500 arrays ......................... 29
ETERNUS4000Model80/100 arrays ................................................................................................. 29
ETERNUS3000 arrays....................................................................................................................... 29
ETERNUS6000 arrays....................................................................................................................... 30
Chapter 1
Disk Storage Arrays
This document provides storage array support information for solutions using
Veritas Storage Foundation and High Availability Solutions 5.0 products by
Symantec.
The following topics are discussed in this chapter:
“Supported products”
“Array settings”
“EMC arrays”
“Hitachi Data Systems (HDS) arrays”
“HP arrays”
“IBM arrays”
“Sun arrays”
Supported products
For the Veritas products by Symantec supported with the devices in this
document, see the Veritas Storage Foundation and High Availability Solutions 5.0
Hardware Compatibility List at http://support.veritas.com/docs/283161.
Supported Technologies
FC
iSCSI:
NOTE: With Solaris 10 Update 5, a disabled iSCSI path will not re-enable
automatically once the path is restored. Sun CR 6719804.
SAS
Array settings
Note: Before implementing any device shown in this document, verify that it is also shown as
supported on the desired platform in the Veritas Storage Foundation and High Availability
Solutions 5.0 Hardware Compatibility List. Storage arrays in this chapter may have the same
characteristics, including bit settings, across all UNIX platforms, or platform-specific settings.
Specialized or platform-specific information appears immediately following the generalized
information for any given array or array series. The tables of information for each device or
family of devices provide the appropriate platform-based settings.
The settings shown for arrays reflect those used in Symantec’s testing, and are not necessarily
the only supported settings.
Failover modes
The Dynamic Multipathing (DMP) failover function of the Veritas products
supports the following array types:
Active/Active (A/A) - Supports simultaneous I/O on all paths
Active/Active-Asymmetric (A/A-A) - Supports simultaneous I/O on all paths, but seeks the
most optimized path for the I/O transmission rate
Asymmetric Logical Unit Access (ALUA) - It characterizes the arrays that support
simultaneous I/O on all paths, but seek the most optimized path for the I/O transmission
rate as defined by SPC3.
Active/Passive (A/P) - Supports I/O on a single primary (active) path, while the secondary
(passive) path is engaged in the event of primary path failure
Active/Passive-Concurrent (A/P-C) - Supports I/O on multiple primary (active) paths, while
the secondary (passive) paths are engaged in the event of failure of all primary paths
Active/Passive-Group (A/P-G) - Supports LUN group failover in which a group of LUNs is
connected through a controller as a single failover entity, and failover occurs at the
controller level rather than the LUN level
Active/Passive-Failover (A/P-F) - Supports I/O on a single primary (active) path, while the
secondary (passive) path is engaged through the use of an explicit command in the event of
primary path failure
Third Party Driver (TPD) - arrays which are under control of a third party multi-pathing
driver which have pass through support for DMP .e.g. EMC Powerpath ,MPxIO,RDAC
Disk Storage Arrays 9
EMC arrays
EMC arrays
The EMC arrays qualified for this release include the:
DMP functionality for the EMC CLARiiON disk arrays requires the following conditions for use
with the supported Veritas products:
Platform Minimum firmware Initiator type Failover mode DMP Failover mode
FLARE 19 (CX)
AIX FLARE 19 (CX3) CLARiiON OPEN Failover Mode=1 TPD=Powerpath
FLARE 28.5 (CX4)
FLARE 19 (CX)
Solaris/Linux/AIX FLARE 19 (CX3) CLARiiON OPEN Failover Mode=1 A/P-F
FLARE 28.5 (CX4)
FLARE 19 (CX)
HP-UX FLARE 19 (CX3) HP NO Auto TRESSPASS Failover Mode=2 A/P-C
FLARE 28.5 (CX4)
Solaris/Linux/ FLARE 26 (CX) CLARiiON OPEN
HP-UX/AIX FLARE 26 (CX3) Failover Mode=4 ALUA, TPD=Powerpath
FLARE 28.5 (CX4)
DMP functionality for the EMC Symmetrix DMX series disk arrays requires the following
conditions for use with the supported Veritas products:
Platform Minimum firmware Fibre Flags SCSI Flags DMP Failover mode
5671.60
a
C, bSC3, SPC2, VCM
(DMX800/1000)
e
(optional), EAN (optional),
AIX 5772.97 (DMX 3) PP.UWN c
A/A
PER (volume based flag),
5773.134 (DMX 4) Link Speed, OS2007
5774 (V-MAX)
5671.60
(DMX800/1000) C, SC3, SPC2, EAN, VCM
Solaris/Li e
5772.97 (DMX 3) PP.UWN (optional), PER (volume A/A
nux/AIX
based flag), Link Speed
5773.134 (DMX 4)
5774 (V-MAX)
5671.60
(DMX800/1000)
C, dV , SPC2, PER, Link
HP-UX 5772.97 (DMX 3)
e
PP.UWN A/A
Speed
5773.134 (DMX 4)
5774 (V-MAX)
Solaris/Li 5671.60
nux/ (DMX800/1000) C, SC3, SPC2, EAN, VCM
e
HP- 5772.97 (DMX 3) PP.UWN (optional), PER (volume A/A
UX/AIX 5773.134 (DMX 4) based flag), Link Speed
5774 (V-MAX)
a
C= Common_Serial_Number – A required setting for VM-DMP and PowerPath functionality
b
SC3 = SCSI3 PGR Director flag
c
PER = SCSI3 Persistent Reserve LUN flag
d
V =Volume Set Addressing (HP-UX-only requirement)
e
PP = only required for swiched environments
The DMP functionality of the arrays requires the following conditions for use with the supported
Veritas products:
DMP
Platform Minimum Firmware Setting 1 Setting 2 Setting 3
Failover
mode
A/A-A
Unique Reserve UA (06/2A00) NACA
AIX 0726/F-M
Mode 1 = ENABLED SUPPRESS MODE Mode
A/A-A
e Unique Reserve
HP-UX 0726/F-M HP-UX MODE
Mode 1 = ENABLED
A/A-A
Linux (RHEL Unique Reserve
0726/F-M
and SUSE) Mode 1 = ENABLED
A/A-A
Unique Reserve
Solaris 0726/F-M
Mode 1 = ENABLED
e
When used with Veritas Storage Foundation for Oracle RAC, set dmp_retry_timeout=5 seconds.
12 Disk Storage Arrays
HDS arrays
HDS TagmaStore USP/NSC and USP V/VM arrays
The DMP functionality of the TagmaStore USP/NSC and USP V/VM arrays
requires the following conditions for use with the supported Veritas products:
DMP
Host Mode
Platform Minimum Firmware Host Mode Host Mode Options Failover
Options
mode
The DMP functionality of AMS2300 series array requires the following conditions for use with the
supported Veritas products:
Platform Minimum Firmware Host Mode System Options DMP Failover mode
The DMP functionality of the Thunder 9500V arrays requires the following conditions for use
with the supported Veritas products:
Error! Reference
source not
DMP Failover
Platform found.
Minimum Setting 1 Setting 2 Setting 3 Setting 4
mode
Firmware
Logical Unit
Persistent Number equal
No_RSV_Conf HP connection to or greater
HP-UX X65B/K RSV Cluster A/A-A
Mode = mode 2 = than 8 can be
ENABLED ENABLED Mode =
ENABLED recognized by
HP-UX
g
X = 0 or 1: 065B/K for model 9570V; 165B/K for model 9580V
14 Disk Storage Arrays
HDS arrays
HDS Lightning 9970V/9980V arrays
The DMP functionality of the Lightning 9970V/9980V arrays requires the following conditions
for use with the supported Veritas products:
DMP
System
Platform Minimum Firmware Host Mode Failover
Options
mode
h
Solaris 21-14-17-00/00 09 (Solaris) 254+186 A/A
h
For deepmapping, the minimum Hitachi HiCommand Device Manager Server version is 5.0.0-02, and the minimum
Hitachi HiCommand Agent version is 5.0.0-0. However, even with these levels, the vxstorage_stats command may take
substantial time to return.
Disk Storage Arrays 15
HP arrays
HP arrays
StorageWorks EVA4000/6000/8000
StorageWorks XP128/1024
StorageWorks XP10000/12000/20000/24000
The DMP functionality of the EVA3000/5000 arrays requires the following conditions for use with
the supported Veritas products:
i
Platform Minimum Firmware Host Mode DMP Failover mode
The DMP functionality of the EVA4000/6000/8000 arrays requires the following conditions for use
with the supported Veritas products:
j Minimum
Platform Host Mode DMP Failover mode
Firmware
AIX 6000 Custom: 00000000001109A8 ALUA
Platform Minimum Firmware Host Mode System Options DMP Failover mode
AIX 21-13-02 0F (AIX) 254+301 A/A
HP-UX 21-13-02 08 (HP-UX) 254 A/A
Linux (RHEL and SUSE) 21-13-02 00 (Linux) 254 A/A
DMP
Minimum
Platform Host Mode System Options Failover
Firmware
P mode
02 (Veritas Storage
50-05-06-00
l Foundation for Oracle
(XP10000/12000)
AIX a 0F (AIX) RAC) A/A
60-01-31-00
22 (Veritas Cluster
(XP20000/24000)
Server)
t
f 02 (Veritas Storage
50-05-06-00
o Foundation for Oracle
(XP10000/12000)
HP-UX 08 (HP-UX) RAC) A/A
60-01-31-00
22 (Veritas Cluster
(XP20000/24000)
m Server)
02 (Veritas Storage
Linux 50-05-06-00
Foundation for Oracle
(RHEL (XP10000/12000)
A 00 (Linux) RAC) A/A
and 60-01-31-00
22 (Veritas Cluster
SUSE) (XP20000/24000)
I Server)
02 (Veritas Storage
50-05-06-00
Foundation for Oracle
(XP10000/12000)
Solaris 09 (Solaris) RAC) A/A
X 60-01-31-00
22 (Veritas Cluster
(XP20000/24000)
Server)
H
Disk Storage Arrays 17
IBM arrays
IBM arrays
XIV
The DMP functionality of the IBM ESS arrays requires the following conditions
for use with the supported Veritas products:
The DMP functionality of the DS4xxx/DS5xxx arrays have the following additional
requirements for use with the supported Veritas products. For Linux platform, the A/P-F
mode support requires ASL/APM .
The DMP functionality of the IBM DS6000 arrays requires the following
conditions for use with the supported Veritas products:
DMP Failover
Platform Host Type Volume Group Type
mode
Volume Group Host Type:
AIX HBA Host Type: IBM pSeries A/P-C
IBM pSeries
Volume Group Host Type:
Linux HBA Host Type: Linux A/P-C
Linux
Solaris Solaris Solaris A/P-C
The DMP functionality of the IBM arrays requires the following conditions for use with the
supported Veritas products:
The DMP functionality of the IBM SVC arrays requires the following conditions
for use with the supported Veritas products
DMP
Minimum
Platform Failover
Firmware mode
All platforms 4.2.1.x ALUA
20 Disk Storage Arrays
Sun arrays
Sun arrays
The Sun arrays qualified for this release include the:
StorEdge™ 2510/2530/2540
StorEdge™ 3510/3511
StorEdge 6320 (T4)
StorageTek 6130/6140/6540/6580/6780
StorageTek 9970/9980
StorageTek 9985V/9990V
Note: This release of the Veritas Storage Foundation and High Availability
Solutions products no longer include support for Sun T3 and T3+ arrays.
The DMP functionality of the Sun 2500 series arrays requires the following conditions
for use with the supported Veritas products:
NDU supportability limitations: “ NDU is not supported between major f/w code upgrade as 6.x to
7.x”
Disk Storage Arrays 21
Sun arrays
Sun StorEdge 6320 (T4)
The DMP functionality of the Sun 6320 arrays requires the following conditions for use with the
supported Veritas products:
Note that this release of the Veritas Storage Foundation and High Availability Solutions
products no longer include the libvxpurple.so ASL to support Sun T3 and T3+ arrays. Those
arrays are now processed as JBODs with a failover mode of A/P. The conditions required for using
the DMP functionality of the Sun arrays with the supported Veritas products are listed in the
section below.
You can configure the Sun StorEdge T4 array in the following modes:
RW (implicit failover or auto-trespass) mode. LUN failover will be triggered on any read or write
command with the exception of a read of LBA 0. To enable the implicit LUN failover, use the sys
mp_support=rw command on the Sun StorEdge T4 array.
MPxIO (explicit failover or nonauto-trespass) mode. (MPxIO is Solaris OS Multipathing)LUN
failover will be triggered with an array specific command. To enable the explicit LUN failover,
use the sys mp_support=mpxio on the Sun StorEdge T4 array. In this mode, you can use the Sun
StorEdge Traffic Manager (SSTM) driver or DMP to handle multipathing. To enable SSTM see the
Solaris documentation.
If you want to enable DMP to handle multipathing, and your system is running Solaris, the
/kernel/drv/scsi_vhci.conf file must have the MPxIO mode enabled (mpxio-disable =”yes”).
If you want to enable DMP to handle multipathing and your system is running Solaris 10,
the /kernel/drv/fp.conf file must have the MPxIO mode enabled (mpxio-disable =”yes”).
Note: All hosts in the clustered environment must use the same configuration set-up for the
T4 array.
22 Disk Storage Arrays
Sun arrays
Sun StorageTek 9970/9980 arrays
The conditions required for using the DMP functionality of the Sun 9970/9980 arrays with
the supported Veritas products are the same as that required by the HDS Lightning
9970V/9980V arrays. For more information, see “HDS Lightning 9970V/9980V arrays” on
page 13.
The conditions required for using the DMP functionality of the Sun 9985V/9990V
arrays with the supported Veritas products are the same as that required by the HDS
TagmaStore USP/NSC and USP V/VM arrays. For more information, see “HDS
TagmaStore USP/NSC and USP V/VM arrays” on page 12.
The DMP functionality of the Sun 6130/6140/6540 arrays requires the following conditions
for use with the supported Veritas products.
The DMP functionality of the Sun 6580/6780 arrays requires the following conditions for
use with the supported Veritas products.
The DMP functionality of the arrays requires the following conditions for use with the supported
Veritas products:
DMP
Platform Minimum Firmware Host Group type Failover
mode
AIX 1.03.01.109.T05 AIX (4) A/P-F
Linux (RHEL
1.03.01.109.T05 Linux (0) A/P-F
and SUSE)
Note: The Host Group type, if using the array GUI, select the OS type (AIX, HPUX, Linux, or Solaris).
If you are using the array CLI, then use the CLI command to select the OS, where the OS type would be “0”
for Linux, “2” for Solaris, “3” for HPUX, and “4” for AIX.
Disk Storage Arrays 25
Huawei Symantec arrays
Oceanspace S2300/S2300E arrays
The DMP functionality of the arrays requires the following conditions for use with the supported
Veritas products:
DMP
Platform Minimum Firmware Host Group type Failover
mode
AIX 1.02.01.206.T03 AIX (4) A/P-F
Linux (RHEL
1.02.01.206.T03 Linux (0) A/P-F
and SUSE)
Note: The Host Group type, if using the array GUI, select the OS type (AIX, HPUX, Linux, or Solaris).
If you are using the array CLI, then use the CLI command to select the OS, where the OS type would be “0” for
Linux, “2” for Solaris, “3” for HPUX, and “4” for AIX.
The DMP functionality of the arrays requires the following conditions for use with the supported
Veritas products:
DMP
Platform Minimum Firmware Host Group type Failover
mode
AIX 1.04.01.203.T01 AIX (4) A/P-F
HP-UX 1.04.01.203.T01 HPUX (3) A/P-F
Linux (RHEL
1.04.01.203.T01 Linux (0) A/P-F
and SUSE)
Solaris 1.04.01.203.T01 Solaris (2) A/P-F
Note: The Host Group type, if using the array GUI, select the OS type (AIX, HPUX, Linux, or Solaris).
If you are using the array CLI, then use the CLI command to select the OS, where the OS type would be
“0” for Linux, “2” for Solaris, “3” for HPUX, and “4” for AIX.
26 Disk Storage Arrays
Huawei Symantec arrays
Oceanspace VIS6300/VIS6600 arrays
The DMP functionality of the arrays requires the following conditions for use with the supported
Veritas products:
DMP
Platform Minimum Firmware Host Group type Failover
mode
AIX 1.05.01.108.T01 AIX (4) A/P-F
Linux (RHEL
1.05.01.108.T01 Linux (0) A/P-F
and SUSE)
Note: The Host Group type, if using the array GUI, select the OS type (AIX, HPUX, Linux, or Solaris).
If you are using the array CLI, then use the CLI command to select the OS, where the OS type would be “0”
for Linux, “2” for Solaris, “3” for HPUX, and “4” for AIX.
Disk Storage Arrays 27
Fujitsu arrays
Fujitsu arrays
The Fujitsu arrays qualified for this release include the:
・ ETERNUS DX60
・ ETERNUS DX80
・ ETERNUS2000
・ ETERNUS8000
・ ETERNUS4000
・ ETERNUS3000
・ ETERNUS6000
AIX V10L11 Reservation Conflict Response for Test Unit Ready: A/A
Normal response
Host Specific Mode: AIX mode
Sense Code Conversion: No conversion
HP-UX V10L11 Reservation Conflict Response for Test Unit Ready: [x]Disable load A/A
Normal response balance
Host Specific Mode: HP-UX mode
Sense Code Conversion: No conversion
AIX V20L11 Reservation Conflict Response for Test Unit Ready: Normal A/A
response Host Specific Mode: AIX Mode (Extended Address)
Sense Code Conversion Pattern: No Conversion
HP-UX V20L11 Reservation Conflict Response for Test Unit Ready: Normal [x]Disable Load A/A
response Balance
Host Specific Mode: HP-UX mode
Sense Code Conversion Pattern: No Conversion
Disk Storage Arrays 29
Fujitsu arrays
ETERNUS8000Model700/900/1100/2100, ETERNUS4000Model300/500 arrays
The DMP functionality of the ETERNUS8000Model700/900/1100/2100 and ETERNUS4000Model300/500 arrays
requires the following conditions for use with the supported Veritas products:
AIX V11L12 Reservation Conflict Response for Test Unit Ready: Normal A/A
response Host Specific Mode: AIX mode
Sense Code Conversion Pattern: No Conversion
HP-UX V11L12 Reservation Conflict Response for Test Unit Ready: Normal [x]Disable Load A/A
response Balance
Host Specific Mode: HP-UX mode
Sense Code Conversion Pattern: No Conversion
ETERNUS4000Model80/100 arrays
The DMP functionality of the ETERNUS4000Model80/100 arrays requires the following conditions for use with
the supported Veritas products:
ETERNUS3000 arrays
The DMP functionality of the ETERNUS3000 arrays requires the following conditions for use with the supported
Veritas products: