Professional Documents
Culture Documents
I. Carefully read each question then select the letter of the best answer. Write you answers beside each item number.
1. Which of the following automotive servicing skills is most commonly performed in a shop?
A. buying B. cleaning C. driving D. repairing
2. If you are a graduate in automotive servicing, what job is most suitable for you?
A. electrician B. gasoline boy C. janitor D. mechanic
3. Which of the following is not part of automotive servicing?
A. car wash B. painting C. selling cars D. vulcanizing
4. Which of the following should you consider most when servicing a car?
A. friendship B. profit C. quality of service D. time
5. How do you describe automotive servicing?
A. hobby B. source of income C. extra job D. all of the above
6. Which of the following is a tooth cutting tool?
A. bolo B. chisel C. hacksaw D. plane
7. What do you call the tools that are used for their sharp edges?
A. edge-cutting B. tooth-cutting C. marking D. boring
8. What do you call the tool used for measuring tire inflation?
A. fuel gauge B. marking gauge C. temperature gauge D. tire pressure gauge
9. What gauge does a gasoline tank have?
A. fuel B. oil C. pressure D. temperature
10. How do you classify pliers and clamps?
A. cleaning tools B. holding tools C. marking tools D. twisting tools
11. What classification do try square and pull push rule belong?
A. cleaning B. holding C. marking D. measuring
12. When you want to get things done with less effort and greater efficiency, what should you use?
A. bench work B. lights C. space D. tools
13. Which of the following skills can you do if you have basic knowledge in tools classification?
A. identify and select tools for the task C. replace defective components of every tool
B. guess the appropriate tool for the job D. presume which tools are really needed for the job
14. What does choosing the right tool require a lot?
A. assumption B. deduction C. practice D. presumption
15. What could be the result of using incorrect tool for the job?
A. efficiency B. good performance C. good values D. injury
16. What does basic level of competency involve?
A. checking & inspection B. disassembling C. major job D. overhauling
17. What is needed to successfully achieve a certain task?
A. constant practice on the use of tools C. careful and proper planning and preparation
B. seldom observance of safety precautions D. courageous use of power tools and equipment
18. What does good preparation give you?
A. confidence B. intelligence C. skill D. weakness
19. Which of the following should be considered when planning and preparing for the task in order to avoid accident?
A. materials B. place C. safety D. waste materials
20. What causes injuries while performing a task in an automotive shop?
A. carelessness B. faulty tools C. unpreparedness D. all of the above
21. Why do we maintain hand tool?
A. to maintain its efficiency C. to avoid injuries during work
B. to avoid buying new one D. all of the above
22. Which of the following is a way of maintaining hand tools?
A. selling it B. buying a new one C. keeping it properly D. not using it
23. What is the base unit for length in the metric system?
A. meter B. millimeter C. gram D. milligram
24. What is the base unit for volume in the metric system?
A. liter B. milliliter C. meter D. millimeter
25. What is the base unit for mass?
A. meter B. liter C. gram D. kilogram
26. What does the prefix ‘kilo’ means?
A. x1 B. x10 C. x100 D. x1000
27. Which of the following is equal to the prefix ‘milli’?
A. x102 B. x10-2 C. x10 3 D. x10-3
28. What process was shown on the picture below?
A. cleaning B. cutting C. measuring D. tightening
29. Which of the following tools is being used in the picture below?
A. 1.5 cm B. 2 cm C. 2.5 cm D. 3 cm
47. The rectangle below is 2 cm wide. What is its length?
II. Prepare an inventory form for the tools below with given conditions. Use the prepared table below.
56. Hammer, 2 pcs, good 59. Philip screw driver, 2pcs, 1 good and 1 defective
57. Hacksaw, 2 pcs, all good 60. Open end wrench, 3 pcs, 2 good, 1 defective
58. Flat screw driver, 1 pc, good
INVENTORY OF TOOLS