Professional Documents
Culture Documents
For
CRAWLAIR® Drilling machine
Model: CM348
ORDERING INSTRUCTIONS
When ordering spare or replacement parts, please specify:
1. The NAME of each part as listed.
2. The PART NUMBER as listed or stamped on the part.
3. The SERIAL NUMBER of the machine.
DONOT use illustration numbers when ordering spare or replacement parts. To save time send all orders
for parts to the nearest branch office or agent. IF IT IS NECESSARY TO SEND ANY PART OF THIS
MACHINE TO THE FACTORY, INQUIRE AT OUR NEAREST BRANCH OFFICE OR AGENT FOR
SPECIAL INSTRUCTIONS. PRODUCT IMPROVEMENT IS A CONTINUING GOAL AT INGERSOLL-
RAND. DESIGN AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGA-
TION.
NOTE: References to the righthand and lefthand sides of the drilling machine are made looking from
the main frame end toward the drill end.
Manual Section
Number Number
Manual Section
Number Number
Manual Section
Number Number
GENERAL ASSEMBLY
1.0 - 1, PL-CM348
PARTS MANUAL MAIN FRAME ASSEMBLY
October 1, 2001 Section 2.0
REF.
NO. PART NO. QTY. PART NAME REMARKS
2.0 - 2, PL-CM348
PARTS MANUAL OSCILLATION CYLINDER
October 1, 2001 Section 2.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 ** 1 O RING
2 ** 1 BACK-UP RING
3 ** 1 O RING
4 ** 1 O RING
5 ** 1 SEAL
6 ** 1 SEAL
7 ** 1 BACK-UP RING
8 ** 2 BACK-UP RING
9 ** 1 WIPER
10 ** 3 WEAR RING
11 ** 2 WEAR RING
12 52138674 1 SEAL KIT (ITEMS MARKED ** )
13 70690235 1 LOCK NUT
14 95201281 3 LUB FITTING
15 51992873 2 PORT PLUG
16 70690219 1 TUBE ASSEMBLY
17 70690201 1 ROD ASSEMBLY
18 70690193 1 HEAD
19 70690185 1 PISTON
2.1 - 1, PL-CM348
PARTS MANUAL UNDERCARRIAGE ASSEMBLY
October 1, 2001 Section 3.0
REF.
NO. PART NO. QTY. PART NAME REMARKS
UNDERCARRIAGE/TRACK ASSEMBLY
3.0 - 1, PL-CM348
UNDERCARRIAGE ASSEMBLY
(For Illustration of parts, refer to page 1)
REF.
NO. PART NO. QTY. PART NAME REMARKS
NOTE: The Track Assembly parts are common to both right-hand and left-hand Track Assem-
blies except where noted. The quantities listed are for two (2) Track Assemblies, one
right-hand and one left-hand; the total number required for a complete machine.
** NOTE: The Motor/Transmission Assembly is not sold as part of the Undercarriage Assembly. It is
included for reference purpose only.
3.0 - 2, PL-CM348
FINAL DRIVE ASSEMBLY
3.1–1
FINAL DRIVE ASSEMBLY
(For Illustration of parts, refer to Page 3.1–1)
REF.
NO. PART NO. QTY. PART NAME
REMARKS
5 50861707 1 SPACER
6 95279006 1 BEARING
7 95033379 2 PLUG, PIPE
8 50867811 1 SHAFT, GEAR
9 50861723 1 SPACER
10 50488584 1 SUPPORT, INSIDE DRIVE
11 50488550 2 BEARING, SUPPORT
12 95422234 2 BEARING, ROLLER
13 50861715 1 RETAINER, BEARING
3.1–2 PL-CM348
TRACK IDLER WHEEL ASSEMBLY
REF.
NO. PART NO. QTY. PART NAME
REMARKS
NOTE: EACH IDLER WHEEL ASSEMBLY, BOTH RIGHT–HAND AND LEFT–HAND, INCLUDES ONE BRACKET,
RIGHT–HAND AND ONE BRACKET, LEFT–HAND. A RIGHT–HAND IDLER WHEEL ASSEMBLY IS ASSEMBLED
WITH THE SIDE OF THE WHEEL THAT INCLUDES THE PLUG FACING THE RIGHT–HAND BRACKET. A LEFT–
HAND IDLER WHEEL ASSEMBLY IS ASSEMBLED SO THAT THE SIDE OF THE WHEEL WITH THE PLUG
FACES THE LEFT–HAND BRACKET.
PL-CM348 3.2–1
IDLER WHEEL ATTACHING PARTS
IDLER
IDLER BRACKET
5
8
6
8
FRAME
REF.
NO. PART NO. QTY. PART NAME
REMARKS
2 50484583 2 PLATE
3 50484591 10 SHIM
4 50484559 28 SHIM
5 50484542 2 PLATE
6 95214995 6 CAPSCREW
7 95214987 2 CAPSCREW
8 95210415 8 LOCKWASHER
PL-CM348 3.3–1
SPRING ADJUSTER ASSEMBLY
2 5
4
7
9 3B
3A
3
3D
8
3C
6
3E
REF.
NO. PART NO. QTY. PART NAME
REMARKS
3B 95201281 1 .FITTING
3C 50533926 1 .PACKING
3D 50489624 1 .WIPER, ROD
3E 50489632 1 .PISTON
4 50489400 1 BRACKET
8 95081907 4 LOCKWASHER
9 95210415 4 LOCKWASHER
PL-CM348 3.4–1
TRACK ROLLER ASSEMBLY
REF.
NO. PART NO. QTY. PART NAME
REMARKS
5 50774405 1 PLUG
6 50771302 2 SEAL
50771997 1 ROLLER/BUSHING
7 50952811 2 .BUSHING
8 50771260 1 .ROLLER
PL-CM348 3.5–1
PARTS MANUAL TRACK CHAIN ASSEMBLY
October 1, 2001 Section 3.8
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 50489467 74 LINK, R. H.
2 50489475 74 LINK, L. H.
3 50774439 74 BUSHING
4 50489491 72 PIN, STANDARD TRACK
5 50489509 2 PIN, MASTER TRACK
6 50774447 296 WASHER, SEAL
7 50489517 296 BOLT
8 50774454 296 NUT
9 50952241 74 PAD, GROUSER
NOTE: The quantities listed are for two (2) complete Track Chain Assemblies, the total number
required for a complete machine.
3.8 - 1, PL-CM348
MOTOR/TRANSMISSION ASSEMBLY
XP1990
REF.
NO. PART NO. QTY. PART NAME
REMARKS
7 95104196 10 CAPSCREW
8 95081907 10 LOCKWASHER
9 95078655 1 PLUG, PIPE
10 51019263 1 VENT, BREATHER
PL-CM348 3.9–1
TRACK DRIVE TRANSMISSION ASSEMBLY
VP1391
PL-CM348 3.10–1
TRACK DRIVE TRANSMISSION ASSEMBLY (SECTIONAL VIEW)
(For Parts List, refer to bottom of this page thru Page 3.10–3)
REF.
NO. PART NO. QTY. PART NAME
REMARKS
6 50861483 3 BEARING
7 50861566 3 GEAR, PLANET
8 50861608 1 GEAR, RING
9 95034047 3 PIN
(CONTINUED)
3.10–2 PL-CM348
TRACK DRIVE TRANSMISSION ASSEMBLY (CONT.)
(For Illustration of parts, refer to Pages 3.10–1 thru 3.10–2)
REF.
NO. PART NO. QTY. PART NAME
REMARKS
16 50861459 2 .PIN
17 50758184 1 PISTON
18 95822664 1 SEAL
19 95087011 1 O–RING
20 50861533 1 COUPLING, MOTOR
30 95822672 1 SEAL
31 50757905 1 SEAL, OIL
32 95018149 1 O–RING
33 95463691 2 PLUG, PIPE
++ NOTE: THIS PART IS NOT SOLD SEPARATELY, IT IS CONTAINED IN HOUSING ASSEMBLY 50906205.
PL-CM348 3.10–3
PROPELLING AIR MOTOR ASSEMBLY
WP14938
PL-CM348 3.11–1
PROPELLING AIR MOTOR ASSEMBLY
(For Illustration of parts, refer to Page 3.11–1)
REF.
NO. PART NO. QTY. PART NAME
REMARKS
19 03167194 4 LOCKWASHER
20 03187226 1 VALVE, ROTARY
21 03185162 1 .PIN, DRIVE (LARGE)
22 03185618 2 .PIN, DRIVE (SMALL)
23 03187242 1 CHEST, VALVE
24 03185170 1 .KEY
25 03187937 1 .BUSHING
26 03188125 1 COVER, VALVE CHEST
27 03610151 5 ASSEMBLY, PISTON
28 03184249 1 .RING, COMPRESSION
(CONTINUED)
3.11–2 PL-CM348
PROPELLING AIR MOTOR ASSEMBLY (CONT.)
(For Illustration of parts, refer to Page 3.11–1)
REF.
NO. PART NO. QTY. PART NAME
REMARKS
++ NOTE: THESE PARTS ARE NOT SOLD SEPARATELY, THEY ARE CONTAINED IN VENT CAP
ASSEMBLY 03167095.
F NOTE: THIS PART IS NOT ILLUSTRATED.
PL-CM348 3.11–3
PARTS MANUAL BOOM ASSEMBLY
October 1, 2001 Section 4.0
BOOM ASSEMBLY
4.0 - 1, PL-CM348
BOOM ASSEMBLY
For Illustration refer to page 1 of Section 4.0
REF.
NO. PART NO. QTY. PART NAME REMARKS
4.0 - 2, PL-CM348
BOOM ASSEMBLY
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 51999266 1 PEDESTAL
2 51903375 1 BUSHING, PEDESTAL
3 50194737 1 BUSHING, BOOM PEDESTAL
1 51776144 1 PEDESTAL
2 50122712 2 BUSHING, LINK
3 50194737 1 BUSHING, BOOM PEDESTAL
4.0 - 3, PL-CM348
PARTS MANUAL BOOM SWING CYLINDER
October 1, 2001 Section 4.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 ** 1 SEAL
2 ** 1 O RING
3 ** 1 BACK-UP RING
4 ** 1 O RING
5 ** 1 SEAL
6 ** 1 WIPER
7 ** 1 O RING
8 ** 2 WEAR RING
9 ** 2 WEAR RING
10 52138690 1 SEAL KIT (ITEMS MARKED ** )
11 52138096 2 WASHER SEAL
12 70690292 1 LOCK NUT
13 51992873 2 PORT PLUG
14 51999316 2 CARTRIDGE VALVE
15 52138104 2 BLEEDER PLUG
16 70690334 1 TUBE ASSEMBLY
17 70690326 1 ROD ASSEMBLY
18 70690318 1 PISTON
19 70690268 1 HEAD
4.1 - 1, PL-CM348
PARTS MANUAL BOOM LIFT CYLINDER
October 1, 2001 Section 4.2
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 ** 1 SEAL
2 ** 1 O RING
3 ** 1 BACK-UP RING
4 ** 1 O RING
5 ** 1 SEAL
6 ** 1 WIPER
7 ** 1 O RING
8 ** 2 WEAR RING
9 ** 2 WEAR RING
10 52138690 1 SEAL KIT (ITEMS MARKED ** )
11 52138096 2 WASHER SEAL
12 70690292 1 LOCK NUT
13 51992873 2 PORT PLUG
14 51999316 2 CARTRIDGE VALVE
15 52138104 2 BLEEDER PLUG
16 70690284 1 TUBE ASSEMBLY
17 70690276 1 ROD ASSEMBLY
18 70690250 1 PISTON
19 70690268 1 HEAD
4.2 - 1, PL-CM348
PARTS MANUAL POWER DUMP & SWING ASSEMBLY
October 1, 2001 Section 5.0
REF.
NO. PART NO. QTY. PART NAME REMARKS
5.0 - 2, PL-CM348
PARTS MANUAL GUIDE DUMP CYLINDER
October 1, 2001 Section 5.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 ** 1 O RING
2 ** 1 WIPER
3 ** 1 SEAL
4 ** 1 BACK-UP
5 ** 1 O RING
6 ** 1 SEAL
7 ** 1 O RING
8 ** 2 WEAR RING
9 ** 3 WEAR RING
10 52138724 1 SEAL KIT (ITEMS MARKED ** )
11 52138096 2 WASHER SEAL
12 70690235 1 LOCK NUT
13 2 PORT PLUG
14 52138104 2 BLEEDER PLUG
15 51999324 2 VALVE
16 70690458 1 TUBE ASSEMBLY
17 70690441 1 ROD ASSEMBLY
18 70690433 1 HEAD
19 70690383 1 PISTON
5.1 - 1, PL-CM348
PARTS MANUAL GUIDE SWING CYLINDER
October 1, 2001 Section 5.2
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 ** 1 SEAL
2 ** 1 O RING
3 ** 1 BACK-UP
4 ** 1 O RING
5 ** 1 SEAL
6 ** 1 WIPER
7 ** 1 O RING
8 ** 2 WEAR RING
9 ** 2 WEAR RING
10 52138716 1 SEAL KIT (ITEMS MARKED ** )
11 52138096 2 WASHER SEAL
12 70690292 1 LOCK NUT
13 2 PORT PLUG
14 52138104 2 BLEEDER PLUG
15 51999324 2 VALVE
16 70690425 1 TUBE ASSEMBLY
17 70690417 1 ROD ASSEMBLY
18 70690250 1 PISTON
19 70690409 1 HEAD
5.2 - 1, PL-CM348
PARTS MANUAL DRILL GUIDE EXTENSION ASSEMBLY
October 1, 2001 Section 6.0
REF.
NO. PART NO. QTY. PART NAME REMARKS
6.0 - 2, PL-CM348
PARTS MANUAL GUIDE EXTENSION CYLINDER
October 1, 2001 Section 6.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
1 ** 1 SEAL
2 ** 1 O RING
3 ** 1 BACK-UP RING
4 ** 1 SEAL
5 ** 1 O RING
6 ** 1 WIPER
7 ** 1 O RING
8 ** 2 WEAR RING
9 ** 2 WEAR RING
10 52137502 1 SEAL KIT (ITEMS MARKED ** )
11 52138096 1 WASHER SEAL
12 70690391 1 LOCK NUT
13 95078655 2 PIPE PLUG
14 51994101 1 CARTRIDGE VALVE
15 52138104 2 BLEEDER PLUG
16 70690375 1 TUBE ASSEMBLY
17 70690367 1 ROD ASSEMBLY
18 70690359 1 HEAD
19 70690342 1 PISTON
6.1 - 1, PL-CM348
PL-CM348
PARTS LIST DRILL GUIDE MOUNTING PARTS
October 1, 2001 Section 7.0
NOTE: IF THE SERIAL NUMBER OF YOUR MACHINE IS BI-851132, BI-851133, BI-851136, BI-851137, OR
BI-851138, ORDER FEED CHAIN 70175088. MACHINES WITH SERIAL NUMBER BI-851139 AND ABOVE,
ORDER FEED CHAIN 50360759.
PARTS LIST DRILL GUIDE ASSEMBLY PL6002
Revision 2 Section 7.3
May 1, 1992
(For Machines with Air Rotary Head) Page 1 of 1
RECOMMENDED SPARES
REF. PART NO. NAME OF THE PART
NO. Parts identified under an item are QTY. CLASS
included with that item. 1 2 3
Min. Av. Max.
70042130 FEED CHAIN ASSEMBLY
1 70042155 CHAIN, FEED 1 - - 1
2 50243690 LINK, COUPLER 2 1 2 4
PARTS LIST CENTRALIZER/FOOTPIECE ASSEMBLY PL6002
Revision 1 Section 7.5-1
(For machines with Drifter)
January 27, 1999 Page 1 of 2
g NOTE: Centralizer Arm 51389658 is removed and Centralizer Arm 70531363 ia added, Centralizer Pin
Lock 51389708 is removed and Centralizer Pin Lock 70531736 is added for SN BI-851244; BI-
851245 and BI-851249 onwards.
n NOTE: The two Half Bushing (50984178) included with this centralizer are used with 1.1/4” (32mm) hex.
or 1.1/2” (38mm) round rods. To use 1.1/4” (32mm) round rods, order two Half Bushings
(50984188). For 1.3/4” Diameter (T45), use Half Bushing 50984228.
(CONTINUED)
CENTRALIZER/FOOTPIECE ASSEMBLY (CONTINUED)
* NOTE: Centralizer Arm 51389658 is removed and Centralizer Arm 70531363 ia added, Centralizer Pin
Lock 51389708 is removed and Centralizer Pin Lock 70531736 is added for SN BI-851244; BI-
851245 and BI-851249 onwards.
** NOTE: These parts are not sold separately; they are contained in Worm and Gear
set 50445774
REF.
NO. PART NO. QTY. PART NAME REMARKS
70693411 MAIN FRAME AIR PIPING - FOR MACHINES WITH AIR ROTARY
HEAD AND TOWER CONTROLS (SECTION 8.2, PL-CM348)
70680087 MAIN FRAME AIR PIPING - FOR MACHINES WITH AIR ROTARY
HEAD AND SIDE CONTROLS (SECTION 8.2.1, PL-CM348)
70693429 DRILL GUIDE AIR PIPING - FOR MACHINES WITH AIR ROTARY
HEAD AND TOWER CONTROLS (SECTION 8.5, PL-CM348)
70680095 DRILL GUIDE AIR PIPING - FOR MACHINES WITH AIR ROTARY
HEAD AND SIDE CONTROLS (SECTION 8.5.1, PL-CM348)
8.0 - 1, PL-CM348
PARTS MANUAL MAIN FRAME AIR PIPING
For Machines with a Drifter and Tower Controls
October 1, 2001 Section 8.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.1 - 2, PL-CM348
MAIN FRAME AIR PIPING
For Illustration refer to page 1 of Section 8.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.1 - 3, PL-CM348
PARTS MANUAL MAIN FRAME AIR PIPING
For Machines with a Drifter and Side Controls
October 1, 2001 Section 8.1.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.1.1 - 2, PL-CM348
MAIN FRAME AIR PIPING
For Illustration refer to page 1 of Section 8.1.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.1.1 - 3, PL-CM348
PARTS MANUAL MAIN FRAME AIR PIPING
For Machines with a Air Rotary Head and Tower Controls
October 1, 2001 Section 8.2
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.2 - 2, PL-CM348
MAIN FRAME AIR PIPING
For Illustration refer to page 1 of Section 8.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.2 - 3, PL-CM348
PARTS MANUAL MAIN FRAME AIR PIPING
For Machines with a Air Rotary Head and Side Controls
October 1, 2001 Section 8.2.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.2.1 - 2, PL-CM348
MAIN FRAME AIR PIPING
For Illustration refer to page 1 of Section 8.2.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.2.1 - 3, PL-CM348
DRILL GUIDE AIR PIPING
PARTS MANUAL
For Machines with a Drifter and Side Controls(12’ drill Steel)
October 1, 2001 Section 8.3.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.3.1 - 2, PL-CM348
DRILL GUIDE AIR PIPING
For Illustration refer to page 1 of Section 8.3.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
49 70017389 1 STUD
50 94037587 2 WASHER, SPRING
51 70690805 2 HOSE, AIR
52 70690755 1 HOSE, AIR
53 70690839 2 HOSE, AIR
54 70667134 1 HOSE, AIR
55 70667126 1 HOSE, AIR
56 50069798 6 CLAMP, HOSE
57 94055555 12 BOLT HEX. HEAD
58 94361888 1 GRIP HANDLE
59 50233246 6 CLAMP, HOSE
60 94055779 12 BOLT HEX. HEAD
61 50581719 2 CLAMP HOSE
62 94076882 1 CABLE, SAFETY
63 50393529 25 STRAP TIE, NOVOFLEX
8.3.1 - 3, PL-CM348
DRILL GUIDE AIR PIPING
PARTS MANUAL For Machines with a Drifter and Tower Controls
(12’ Drill Steel)
October 1, 2001 Section 8.3.2
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.3.2 - 2, PL-CM348
DRILL GUIDE AIR PIPING
For Illustration refer to page 1 of Section 8.3.2
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.3.2 - 3, PL-CM348
DRILL GUIDE AIR PIPING
PARTS MANUAL For Machines with a Air Rotary Head and Guide Controls
(10’ Drill Steel)
October 1, 2001 Section 8.5
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.5 - 2, PL-CM348
DRILL GUIDE AIR PIPING
For Illustration refer to page 1 of Section 8.5
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.5 - 3, PL-CM348
PARTS MANUAL DRILL GUIDE AIR PIPING
For Machines with a Air Rotary Head and Side Controls
October 1, 2001 Section 8.5.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.5.1 - 2, PL-CM348
DRILL GUIDE AIR PIPING
For Illustration refer to page 1 of Section 8.5.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
8.5.1 - 3, PL-CM348
PARTS LIST PL6002
Revision 1 LUBRICATOR ASSEMBLY Section 8.10
November 1, 1991 Page 1 of 1
REF.
NO. PART NO. QTY. PART NAME REMARKS
9.0 - 1, PL-CM348
PARTS MANUAL HYDRAULIC PIPING
For Machines with Drifter
October 1, 2001 Section 9.1
HYDRAULIC PIPING
9.1 - 1, PL-CM348
HYDRAULIC PIPING
For Illustration refer to page 1 of Section 9.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
9.1 - 2, PL-CM348
PARTS MANUAL HYDRAULIC PIPING
For Machines with Rotary Head
October 1, 2001 Section 9.2
HYDRAULIC PIPING
9.2 - 1, PL-CM348
HYDRAULIC PIPING
For Illustration refer to page 1 of Section 9.2
REF.
NO. PART NO. QTY. PART NAME REMARKS
9.2 - 2, PL-CM348
PARTS LIST PL6002
Revision 3 HYDRAULIC VALVE ASSEMBLY Section 9.3
May 22, 1996 Page 1 of 2
++ NOTE: THESE PARTS ARE NOT SOLD SEPARATELY,THEY ARE CONTAINED IN SEAL KIT # 94075462
** NOTE: ONE SET OF ITEM 9 CONSISTS OF 2 SETS OF COMPOSITE BUSHING (LH AND RH)
PARTS LIST PL6000
HYDRAULIC PUMP AIR MOTOR ASSEMBLY Section 9.6
July 1, 1990 Page 1 of 1
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.0 - 1, PL-CM348
PARTS MANUAL NAME PLATE ASSEMBLY
For Machines with Drifter and Tower Controls
October 1, 2001 Section 10.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.1 - 2, PL-CM348
PARTS MANUAL DECAL ASSEMBLY
For Machines with Drifter and Tower Controls
October 1, 2001 Section 10.1.1
DECAL ASSEMBLY
10.1.1 - 1, PL-CM348
DECAL ASSEMBLY
For Illustration refer to page 1 of Section 10.1.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.1.1 - 2, PL-CM348
PARTS MANUAL NAME PLATE ASSEMBLY
For Machines with Drifter and Side Controls
October 1, 2001 Section 10.2
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.2 - 2, PL-CM348
PARTS MANUAL DECAL ASSEMBLY
For Machines with Air Rotary Head and Tower Controls
October 1, 2001 Section 10.2.1
DECAL ASSEMBLY
10.2.1 - 1, PL-CM348
DECAL ASSEMBLY
For Illustration refer to page 1 of Section 10.2.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.2.1 - 2, PL-CM348
PARTS MANUAL NAME PLATE ASSEMBLY
For Machines with Air Rotary Head and Tower Controls
October 1, 2001 Section 10.3
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.3 - 2, PL-CM348
PARTS MANUAL DECAL ASSEMBLY
For Machines with Drifter and Side Controls
October 1, 2001 Section 10.3.1
DECAL ASSEMBLY
10.3.1 - 1, PL-CM348
DECAL ASSEMBLY
For Illustration refer to page 1 of Section 10.3.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.3.1 - 2, PL-CM348
PARTS MANUAL NAME PLATE ASSEMBLY
For Machines with Air Rotary Head and Side Controls
October 1, 2001 Section 10.4
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.4 - 2, PL-CM348
PARTS MANUAL DECAL ASSEMBLY
For Machines with Air Rotary Head and Side Controls
October 1, 2001 Section 10.4.1
DECAL ASSEMBLY
10.4.1 - 1, PL-CM348
DECAL ASSEMBLY
For Illustration refer to page 1 of Section 10.4.1
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.4.1 - 2, PL-CM348
PARTS MANUAL DECAL KIT - SAFETY
October 1, 2001 Section 10.5
REF.
NO. PART NO. QTY. PART NAME REMARKS
10.5 - 2, PL-CM348
PARTS LIST OPTIONAL EQUIPMENT PL-CM348
Section 11.0
February, 2002 Page 1 of 1
NOTE: REPLACE EXISTING FASTENERS WITH ITEM 7 & 8 FOR MOUNTING ROD BOX.
PL-CM348
PARTS LIST ROD RACK ASSEMBLY
March 1, 2002 Section 11.17
1 51027571 1 CRADLE
2 70564364 1 CYLINDER, HYDRAULIC
(REFER TO PL-CM348, SECTION 11.18)
3 51027597 1 SUPPORT
4 -- 1 CHAIN, LINK (NOT SOLD SEPERATELY)
5 50535293 1 HANDLE
6 50535251 1 PLATE
7 50492743 2 PIN, CLEVIS
8 94064904 8 BUSHING, CLEVIS
9 95223996 6 RING, RETAINING
10 95201307 4 FITTING
11 51027613 1 PIN, CLEVIS
12 94042330 8 SCREW
13 94037660 8 LOCK WASHER
14 50196773 2 BUSHING, CYLINDER
16 50034826 2 CLAMP
17 94053311 2 SCREW
18 97140966 2 LOCK WASHER
19 70089974 2 ASSEMBLY, HOSE
20 51027522 2 PLATE
21 70195672 1 DECAL
23 94364296 1 SECTION, VALVE
24 51236495 1 KIT, SEAL
25 51236487 1 KIT, HANDLE
26 51236503 1 KIT, CHECK VALVE
27 51236578 1 KIT, SEAL
28 94368990 1 KIT, TIE ROD
29 94080850 2 ADAPTER
97126080 2 O RING
30 97113898 1 ADAPTER
31 97113955 1 ADAPTER