Professional Documents
Culture Documents
ON
G+3 STORAGE BUILDING- BANGALORE
By
V. ANIL KUMAR
1
CONTENTS
1. Superstructure 3
2. Substructure 9
3. Detailing 12
2
1. Superstructure
Structure Information:
No. of Floors 6(G+3+Terr+OHT)
Total Height 18
Plan Dimensions 52.875m x 42.5m
Typical Floor Height 3m
Architectural Plan
3
Structure Layout Typical floor
Materials:
Concrete M30
Steel HYSD500
Sections:
Columns 500x500mm600x600mm,800x800mm,
800mm,800x900mm
Beams 300x700mm,400x800mm
4
Slabs 150mm,200mm,300mm,350mm,450mm
Walls 150mm
Shell Loads:
Load Set Dead Load (kN/m2) Live Load (kN/m2)
Storage 1.5 7.5
Service 1.5 3
Wash 3 2
Terrace 3 1.5
OHT 6 0.75
Stair Case 3 4
Lobby 1.5 4
Kitchen 1.5 3
Dining 1.5 4
Office 1.5 3
Frame Loads:
External Wall 5.06 kN/m2
Internal Wall 3.45 kN/m2
Parapet 1.8 kN/m2
5
Earthquake Load: As per IS 1893:2016 part 1
Zone Factor II
Importance Factor 1.5
Response Reduction Factor 3
Soil Type II (Medium)
Mass Source DL-1, LL-0.25,LL1-0.5
Time Period Tx-0.222s, Ty-0.248s
Base Shear Sx-8200.21 kN, Sy-8200.21 kN
6
Property Modifiers:
Section Unfactored Loads (Service) Factored Loads (Strength)
Columns 1.0Ig 0.7Ig
Beams 0.5Ig 0.35Ig
Slabs 0.35Ig 0.25Ig
Walls 1.0Ig 0.7Ig
Stability Checks:
Check Load Case Allowable Observed
Inter Story Drift ( Service) (mm) Spec X 0.003 0.0024 SAFE
Spec Y 0.003 0.0023
Max. Def. against EQ (Service) (mm) Spec X 72 27.88 SAFE
Spec Y 72 27.76
Max. Def. against Wind (mm) Wx 30 0.44 SAFE
Wy 30 0.659
Vertical deflection (mm) DL+LL 20 17.1 SAFE
Modal Analysis:
b) No. of modes given should be given in such a way that around 95% to 98% modal
mass participation ratio shall be achieved.
Sum UX=98.42%
Sum UY=96.36%
7
Torsional Irregularity: Torsion Irregularity observed in X-Direction.
Buckling: Buckling is not considered because Slenderness ratio of Building is less than 4
8
2. Substructure Details:
Structure Information:
Materials:
9
Checks:
Slabs 25 mm
Beams 40 mm
Columns 40 mm
Walls 40 mm
Foundation Top-50mm, Bottom-60mm
Load Combinations:
For Strength
1.5DL + 1.5LL
1.2DL + 1.2LL + SPEC X/Y
0.9DL + 1.2LL + SPEC X/Y
0.9DL + 1.5SPEC X/Y
1.5DL +/- 1.5W X/Y
1.2DL +1.2LL +/-1.2W X/Y
1.5DL +/- 1.5W X/Y
1.2 DL +/- 1.2LL +/- 1.2W X/Y
0.9 DL +/- 1.5W X/Y
For Service
1DL + 1LL
1DL + 1SPEC X/Y
1DL + 0.8LL + 0.8SPEC X/Y
Code Details
IS-456 2000 For RCC Design
IS-1893 Part-1, 2016 For Earthquake Loads
IS-875 Part-1, 1987 For Dead Loads
IS-875 Part-2, 1987 For Live Loads
10
IS-875 Part-3, 2015 For Wind Loads
IS-13920 2016 For Ductile Detailing
Softwares used:
11
3. Detailing:
Column 21
12
Column 44
13
Shear Wall PW1
14