Professional Documents
Culture Documents
Fast Data Configuration Guide For Ipasolink 200' PDF
Fast Data Configuration Guide For Ipasolink 200' PDF
NE Login
1. Connect the PC to the LCT port of IDU.
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第2页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
Equipment Configuration
1. Expand Equipment Setup -> Equipment Configuration from the WebLCT
menu.
2. Click the Setup.
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第3页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
4. Set Modem1 as used, and then click Next.
5. Confirm that the setup parameter changes to blue, and then click OK
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第4页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第5页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
Radio Configuration
1. Expand Equipment Setup -> Radio Configuration from the WebLCT menu.
2. Click Setup. The Step1 Window appears
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第6页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第7页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第8页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
3. Confirm that the setup parameter and then click OK
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第9页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 10 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
TX Power Setting
1. Expand Provisioning -> MODEM Function Setting-> TX Power Setting
2. Click the MODEM1 to configure. The TX Power Setting dialog box appears.
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 11 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
4. The default IP address is 172.18.0.1 for Near End site IDU, 172.18.0.2 for Far End
site IDU.
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 12 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
3. Click Setup button. Set NMS and NE1 port as used.
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 13 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
E1 Port Setting
1. Expand Provisioning -> E1/STM-1/Cross Connect Setting -> E1 Port Setting
2. Click the Modify button. The E1 Port Setting (Main Board) dialog box appears
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 14 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
2. Click the desired Port No. to configure. The ETH Port Setting dialog box appear
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 15 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 16 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
Notes:1.Select which Port will be used, and the Vlan mode is Access or
Trunk depend on the BTS. If the IP packet from BTS with TAG, select
Trunk mode. If no Tag, select Access mode.
2. Setting Modem1 as Trunk mode, too(must be Trunk mode).
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 17 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 18 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
2. Click MODEM1
3. Confirm the RX level is up to the design value, and the BER is better than 0.0E-8.
4. Expand Current Status-> Active alarm
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 19 页
All Rights reserved, No Spreading abroad without Permission of ZTE
内部公开 Internal Use Only▲
2. Click Modem1
<以上所有信息均为中兴通讯股份有限公司所有,不得外传> 第 20 页
All Rights reserved, No Spreading abroad without Permission of ZTE