Professional Documents
Culture Documents
Butterfly Valve GRW PDF
Butterfly Valve GRW PDF
Features
• Wafer and lugged body design with face-to-face
dimension, according to EN 558 Series 20 and
API 609.
• Designed according to EN 593 and API 609.
• The seat is field replaceable and fully isolates
the body and shaft from the flow.
• Primary shaft sealing exceeds the pressure
rating of the valve and prevents leakage through
shaft area to atmosphere.
• A secondary shaft sealing provides back-up
safety.
• A molded-in O-ring in the seat for flange sealing
eliminates the need for gaskets.
• Shaft seals prevent moisture penetrating into
the shaft area.
• The two piece shaft allows for a thin disc and
provides minimal obstruction to flow (up to
DN 300).
• Rounded polished disc edge gives full
concentric sealing, lower torques, longer seat
life and drop-tight shut-off.
• Body locating holes allow ease of installation
and centering between the flanges.
• Extended body neck allows for pipe insulation.
• Actuator flange according to ISO 5211.
• Top and bottom shaft bearings for optimized
support and minimum friction and decreased
torque.
• Top bushing absorbs actuator side thrust loads.
• All valves comply to Pressure Equipment
Directive (97/23/EU) Module B1 + D,
CE Marking.
• Available approvals: KIWA, ABS, WRAS, ACS,
NSF/ANSI STD 61.
• Sizes DN 20 up to DN 40 might deviate from
the above mentioned features. Please contact
factory.
www.pentair.com/valves Pentair reserves the right to change the contents without notice KEYEW-6268-EN-1306
Keystone Series GR Resilient Seated Butterfly Valves
GRW/GRL Sizes DN 20-900 (ISO)
8
Series GRW/GRL Parts list
DN 50-300 6
(GRW shown) Item Qty Description
1 1 Body
9 2 1 Seat
3 1 Disc
4 4 1 Upper shaft
5 1 Lower shaft
7
6 1 Upper bushing
10 7 1 Packing
8 1 Body circlip
9 1 Shaft circlip
1 10 2 Upper and lower bearing
11 1 Plug
10
3 5
11
10
12
12
14
13
3 2
15
Pentair reserves the right to change the contents without notice page 2
Keystone Series GR Resilient Seated Butterfly Valves
GRW/GRL Sizes DN 20-900 (ISO)
Material specification
DN 20-40
Body Ductile iron GJS-400-15 EN JS-1030
Disc Stainless steel GX5CrNiMo19-11-2 EN 1.4408 Comparable with CF8M
Shaft Stainless steel X17CrNi16-2 EN 1.4057 Similar to ASTM A276/Gr. 431
Seat EPDM
NBR
EPDM-A
EPDM-WA3
DN 50-300
Body Ductile iron GJS-400-15 EN JS-1030
Disc Super duplex GX2CrNiMoN26-7-4 EN 1.4469
316 stainless steel GX5CrNiMo19-11-2 EN 1.4408 Comparable with CF8M
304 stainless steel GX5CrNiMo19-10 EN 1.4308 Comparable with CF8
Aluminium bronze CuAl10Fe2-C EN CC331G
Nickel aluminium bronze CuAl10Fe5Ni5 EN CC333G
Ductile iron CTD GJS-400-15 EN JS-1030 CTD = Nickel plating
Shaft 316 stainless steel X5CrNiMo17-12-2 EN 1.4401
431 stainless steel X17CrNi16-2 EN 1.4057
Super duplex GX2CrNiMoN25-7-4 EN 1.4410
Seat EPDM Food grade
NBR Food grade
White NBR
FKM
Bushing Polyester
Packing NBR
Bearing PTFE/steel
Circlip Stainless steel
Plug Carbon steel
DN 350-900
Body Ductile iron GJS-400-15 EN JS-1030
Disc Super duplex GX2CrNiMoN26-7-4 EN 1.4418
Duplex GX2CrNiMoN22-5-3 EN 1.4470
316 stainless steel GX5CrNiMo19-11-2 EN 1.4408 Comparable with CF8M
304 stainless steel GX5CrNiMo19-10 EN 1.4308 Comparable with CF8
Aluminium bronze CuAl10Fe2-C EN CC331G
Nickel aluminium bronze CuAl10Fe5Ni5 EN CC333G Comparable with BS 1400 AB2
Ductile iron CTD GJS-400-15 EN JS-1030 CTD = Epoxy coated, max. temp. 120°C
Shaft 431 stainless steel X17CrNi16-2 EN 1.4057 Similar to ASTM A276/Gr. 431
Duplex X2CrNiMoN22-5-3 EN 1.4462
Super duplex X2CrNiMoN25-7-4 EN 1.4410
Seat EPDM Food grade
NBR Food grade
FKM
Disc screw Super duplex GX2CrNiMoN25-7-4 EN 1.4410
Duplex X2CrNiMoN22-5-3 EN 1.4462
Disc screw O-ring EPDM
NBR
FKM
Plug Carbon steel
Plug O-ring NBR
Plug circlip Stainless steel
Bushing Polyester
Shaft/Body O-ring NBR
Bearing PTFE/steel
Shaft/Body circlip Stainless steel
Note:
Valves with super duplex disc will have super duplex disc screw. All other discs will have a duplex disc screw.
Pentair reserves the right to change the contents without notice page 3
Keystone Series GR Resilient Seated Butterfly Valves
GRW/GRL Sizes DN 20-900 (ISO)
H
øN
45˚
α øN
øE øG øE
A
F L
A
F øG
C øB
C
øB
Q øA øM øYY Q øA øM øYY
J J
A D
A
D
Pentair reserves the right to change the contents without notice page 4
Keystone Series GR Resilient Seated Butterfly Valves
GRW/GRL Sizes DN 20-900 (ISO)
H
45˚ øN α øN
øE øE
øG
A
F L øG
A
F
C øB
C
øB
Q øA øM øYY Q øA øM øYY
J
J
A D
A
D
Series GRW & GRL Dimensions of tapped flange locating holes (mm)
Size Series GRW Series GRL
Note: All holes in lugged
(DN) U V U V
version are through
threaded, except the 700 45.5 5.5 45.5 5.5
holes closest to top and 750 65 25 45.5 5.5
bottom shaft. 800 60 20 45.5 5.5
900 54.5 6.5 54.5 6.5
Pentair reserves the right to change the contents without notice page 5
Keystone Series GR Resilient Seated Butterfly Valves
GRW/GRL Sizes DN 20-900 (ISO)
Application II
Other liquid media and lubricating gases (aqueous liquids, such as food & beverage, water, etc.);
and with minor deposit or chemical attack, valve operated at least once a month.
Temperature range from 0°C to maximum temperature rating of the elastomer seat.
Application III
a. Dry non-abrasive media or gases (non-abrasive powders and dry gas); or
b. Fluids with moderate deposit or chemical attack; or
c. Valves operated less than once a month.
Temperature range from 0°C to maximum temperature rating of the elastomer seat.
Application IV
a. Dry abrasive media and degreasing applications (sand, cement, silicone free, oxygen cleaned); or
b. Liquids with severe deposit; or
c. Valves not frequently operated (once a year).
All above with temperature range from -10°C to maximum temperature rating of the elastomer seat.
Notes:
1. For applications with temperatures above or below the guidelines above, please consult factory.
2. For dry service valves it is suggested to use U/C discs (reduced diameter) when service
conditions are less than 3.5 bar.
Notes:
3.5 U/C refers to reduced diameter disc option.
(1) Use a minimum of Class 8.8 steel bolts to connect actuator to valve.
(2) Duplex shaft not suitable for these conditions, use only 431 stainless steel or super duplex.
Pentair reserves the right to change the contents without notice page 6
Keystone Series GR Resilient Seated Butterfly Valves
GRW/GRL Sizes DN 20-900 (ISO)
Pressure-temperature diagram
Seat Disc Body Size range Valve function Temperature (°C)
material * material material (DN) Standard / End of Line -10 0 50 100 120 130 150 160
Pentair reserves the right to change the contents without notice page 7
Keystone Series GR Resilient Seated Butterfly Valves
GRW/GRL Sizes DN 20-900 (ISO)
Ordering information
Example: GR L 100 D 1 2 E D3 I B0 UC
DN 100 Series GR Lug style, Ductile iron body,
316SS disc, 431SS shaft, EPDM seat,
PN 16, ISO 5211, bare shaft, U/C disc
GRL 100 D12E D3 I B0 UC
Series
GR
Body style
L – Lug
W – Wafer
Size (DN)
020 040 080 150 300
450 700 900
025 050 100 200 350
500 750
032 065 125 250 400
600 800
Body material
D – Ductile iron
Disc material
1 – 316 stainless steel 4 – Ductile iron / ENP 7 – Super duplex
2 – 304 stainless steel 5 – Ductile iron / Epoxy ctd. N – Nickel aluminium bronze
3 – Aluminum bronze 6 – Duplex
Shaft (1,2)
1 – 316 stainless steel 6 – Duplex
2 – 431 stainless steel 7 – Super duplex
Notes:
(1) The standard material is 431 stainless steel.
316 stainless steel shaft is available as an option in DN 50-300.
(2) DN 350-900 valves with a super duplex disc will have a super duplex disc screw.
All other disc materials will have a duplex disc screw.
Seat
E – EPDM (Food grade) N – NBR (Food grade) F – FKM W – White NBR
Flange drilling (refer to flange accomodation chart for code selection, see below)
Single drilled
A1 – ASME 125/150 AE – AS2129 Table E D1 – DIN PN 6 D3 – DIN PN 16
AD – AS4087 PN 16 B1 – BS Table E D2 – DIN PN 10 J2 – JIS 10K
Multidrilled
M1 – DN PN 10/16, ASME 125/150, BS Table E, JIS 10K
M2 – DN PN 10/16, ASME 125/150, BS Table E
M3 – DN PN 6/10/16, ASME 125/150, BS Table E
M4 – DN PN 10/16, JIS 10K
M5 – DN PN 6/10/16, ASME 125/150, BS Table E, JIS 10K Multidrilled locating plates
Mounting
I – ISO 5211
Actuation
B0 – Bare shaft G1 – Gear P1 – Pneumatic DA E – Electric
H1 – 10 pos handle C1 – Chainwheel P2 – Pneumatic SR
Flange accommodation chart for wafer valves Flange accommodation chart for lug valves
Sizes (DN) Sizes (DN)
Ord. Ord. Ord. Ord. Ord. Ord. Ord. Ord. Ord. Ord. Ord. Ord. Ord. Ord.
Drillings 20 code 25 code 32 code 40 code 50-500
code 600 code
700-900
code Drillings 20 code 25 code 32 code 40 code 50-500
code 600 code
700-900
code
PN 6 NA - STD M3 Mod. D1 STD M5 Mod. D1 Mod. D1 Mod. D1 PN 6 NA - STD D1 STD D1
STD D1 A-o D1 A-o D1 A-o D1
PN 10 STD D2 STD M3 STD M4 STD M5 STD M1 STD M2 A-o D2 PN 10 STD D2 STD D2 STD D2 STD D2 A-o D2 A-o D2 A-o D2
PN 16 STD D3 STD M3 STD M4 STD M5 STD M1 STD M2 A-o D3 PN 16 STD D3 STD D3 STD D3 STD D3 A-o D3 A-o D3 A-o D3
ASME 125/150 NA - STD M3 Mod. A1 STD M5 STD M1 STD M2 A-o A1 ASME 125/150
NA - STD A1 Mod.
A1
STD A1 A-o A1 A-o A1 A-o A1
BS Table E NA - STD M3 Mod. B1 STD M5 STD M1 STD M2 A-o B1 BS Table E Mod. B1 STD B1 Mod. B1 STD B1 A-o B1 A-o B1 A-o B1
JIS 10K NA - Mod. J2 STD M4 STD M5 STD M1 NA - A-o J2 JIS 10K NA - NA. - STD M4 STD J2 A-o J2 NA - A-o J2
Mod. = Modifications required - Is possible but will require some modifications and will be a special A-o = As ordered - All valves have to be ordered as this drilling using the code above
STD = Standard valve locating plate is multi drilled and covers this flange standard NA = Not possible on this valve size
Pentair reserves the right to change the contents without notice page 8