Professional Documents
Culture Documents
GETTING
STARTED?
EASY.
ZWD 71460 CW
EN User Manual
Washer Dryer
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
WARNING!
Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
• Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away unless
continuously supervised.
• Children of less than 3 years of age should be kept away
unless continuously supervised.
• Do not let children play with the appliance.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the door
is open.
• If the appliance has a child safety device, it should be activated.
• Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
• Do not change the specification of this appliance.
• This appliance is intended to be used in household and similar
applications such as:
– staff kitchen areas in shops, offices and other working
environments;
2
– by clients in hotels, motels, bed & breakfast and other
residential type environments;
– areas for communal use in blocks of flats or in launderettes.
• The appliance shall be installed as a freestanding product or
below the kitchen worktop if space margins permit.
• Do not install the appliance behind a lockable door, a sliding
door or a door with a hinge on the opposite side, that would
prevent the appliance door from being fully open.
• Connect the mains plug to the mains socket only at the end of
the installation process. Make sure that the mains plug is
accessible after installation.
• The ventilation opening in the base must not be covered by a
carpet, mat, or any floor covering.
• WARNING: The appliance must not be supplied through an
external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by a utility.
• Ensure good air ventilation in the room where the appliance is
installed to avoid the backflow of unwanted gases into the room
from appliances burning gas or other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is used for
exhausting fumes from any appliances burning gas or other
fuels.
• The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
• Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
• The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
• Wipe away lint or packaging debris that has accumulated
around the appliance.
3
• Items that have been soiled with substances such as vegetable
or mineral oil, acetone, alcohol, petrol, kerosene, spot removers,
turpentine, waxes and wax removers should be washed
separately with an extra amount of detergent before being dried
in the washer dryer.
• Do not use the appliance if items have been soiled with
industrial chemicals.
• Do not dry unwashed items in the wash dryer.
• Items such as foam rubber (latex foam), shower caps,
waterproof textiles, and rubber backed articles and clothes, or
pillows fitted with foam rubber pads should not be dried in the
washer dryer.
• Fabric softeners, or similar products, should only be used as
specified by the product manufacturer’s instructions.
• Remove all objects from items that could be a source of fire
ignition such as lighters or matches.
• Never stop the washer dryer before the end of the drying cycle
unless all items are quickly removed and separated so that
residual heat can dissipate.
• The final part of the washer dryer cycle takes place without heat
(cool down cycle) to ensure that items reach a temperature that
will not cause damage to them.
• Do not use high pressure water sprays and/or steam to clean
the appliance.
• Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
• Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
SAFETY INSTRUCTIONS
INSTALLATION • Do not install or use the appliance where the
temperature can be less than 0°C or where it is
The installation must comply with exposed to the weather.
relevant national regulations. • Always keep the appliance vertical when it is
being moved.
• Follow the installation instructions supplied with • Make sure that there is air circulation between
the appliance. the appliance and the floor.
• Remove all the packaging and the transit bolts.
4
• The floor area on which the appliance is to be • Do not put flammable products or items that are
installed must be flat, stable, heat resistant and wet with flammable products in, near or on the
clean. appliance.
• Keep the transit bolts in a safe place. If the • Do not touch the glass door while a programme
appliance is to be moved in the future they must is in operation. The glass can get hot.
be reattached to lock the drum to prevent an • Do not dry damaged (torn, frayed) items that
internal damage. contain padding or fillings.
• Always take care when moving the appliance as • If laundry has been washed with a stain
it is heavy. Always use safety gloves and remover, carry out an additional rinse cycle
enclosed footwear. before starting a drying cycle.
• Do not install or use a damaged appliance. • Make sure that all metal objects are removed
• Do not install the appliance where the appliance from the laundry.
door cannot be fully opened. • Only dry fabrics that are suitable to dry in the
• Adjust the feet to have the necessary space washer dryer. Follow the cleaning instruction on
between the appliance and the flooring. the item label.
• When the appliance is in its permanent position, • Plastic items are not heat resistant.
check if it is levelled correctly with the aid of a – If a detergent ball is used, remove it before
spirit level. If it is not, adjust the feet accordingly. starting a drying programme.
– Do not use a detergent ball if setting a non-
ELECTRICAL CONNECTION stop programme.
• The appliance must be earthed. • Do not sit or stand on the open door.
• Always use a correctly installed shockproof • Do not dry dripping wet clothes in the
socket. appliance.
• Do not use multi-plug adapters and extension
cables. SERVICE
• Do not pull the mains cable to disconnect the • To repair the appliance contact an Authorised
appliance. Always pull the mains plug. Service Centre.
• Do not touch the mains cable or the mains plug • Use original spare parts only.
with wet hands.
• UK and Ireland only. This appliance is fitted with DISPOSAL
a 13 A mains plug. If it is necessary to change
the mains plug fuse, use only a 13 A ASTA (BS • Disconnect the appliance from the mains
1362) fuse. electrical and water supplies.
• This appliance complies with the E.E.C. • Cut off the mains electrical cable close to the
Directives. appliance and dispose of it.
• Remove the door catch to prevent children or
WATER CONNECTION pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with
• Do not cause damage to the water hoses. local requirements for the disposal of Waste
• Before connection to new pipes, pipes not used Electrical and Electronic Equipment (WEEE).
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
USE
5
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1 2 3 1 Worktop
2 Detergent dispenser
3 Control panel
4 Door handle
5 Rating plate
4 6 Drain pump filter
5 7 Feet for levelling the appliance
6
CONTROL PANEL
CONTROL PANEL DESCRIPTION
1 2 3 4
Cotton
5
Cotton
Dry Economy 90° 60° 40°
Wool Wool
1400 1200 800 7
Dry
400 Auto Dry Extra Rinse
Rinse Delicates
Spin
8
Spin Mix 20°
Start/Pause
Drain Super ECO
11 10 9
DISPLAY
A B C
G F E D
7
Time area : Programme duration
: Delay start
: Alarm codes
A : Message of error
: Quick indicator
PROGRAMMES
PROGRAMME CHART
Maximum load
Programme Programme description
Reference spin
Temperature range (Type of load and soil level)
speed
Washing programmes
7 kg White cotton and coloured cotton. Normal,
Cotton
1400 rpm heavy and light soil.
90°C - (Cold)
8
Maximum load
Programme Programme description
Reference spin
Temperature range (Type of load and soil level)
speed
9
Maximum load
Programme Programme description
Reference spin
Temperature range (Type of load and soil level)
speed
Programme
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■ ■ ■1) ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■
■ ■ ■ ■ ■ ■ ■
■ ■ ■ ■1) ■
■ ■ ■ ■ ■
10
Programme
■ ■ ■
■ ■ ■ ■ ■
■2) ■ ■
Spin Suggested
Dryness Level Type of fabric Load (kg) speed duration
(rpm) (mins)
11
Spin Suggested
Dryness Level Type of fabric Load (kg) speed duration
(rpm) (mins)
CONSUMPTION VALUES
Stated values are obtained in laboratory conditions with relevant standards. Different cau-
ses can change the data: the quantity and type of laundry and ambient temperature. Wa-
ter pressure, the supply voltage and the temperature of inlet water may also affect the
washing programme duration.
Technical specifications may be changed without prior notice to improve the quality of
product.
At the start of the programme, the display shows the programme duration for the maxi-
mum load capacity.
During the washing phase the programme duration is automatically calculated and can be
greatly reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton
60°C, maximum load capacity 7 kg, the programme duration exceeds 2 hours; actual load
1 kg, the programme duration will be less than 1 hour).
When the appliance is calculating the real programme duration a dot flashes in the dis-
play.
12
Energy con- Approximate pro-
Water con-
Programmes Load (kg) sumption gramme duration (mi-
sumption (litre)
(kWh) nutes)
OPTIONS
TEMP. You cannot set all time values for
Set this option to change the default temperature. different types of fabrics.
Indicator = cold water.
The display shows the set temperature. AUTO DRY
With this option you can set an automatic level of
SPIN dryness for the laundry. The display shows the
With this option you can change the default spin symbol of the set level.
speed. • Extra dry level for cotton items
The indicator of the set speed comes on.
• Cupboard dry level for cotton and synthetic
Additional spin options: items
No Spin • Iron dry level for cotton items
• Set this option to deactivate all spin phases.
Only the drain phase is available.
PREWASH
• The related indicator comes on.
• Set this option for very delicate fabrics. With this option you can add a prewash phase to a
• The rinses phase uses more water for some washing programme.
washing programmes. Use this option for heavy soil.
When you set this option the programme duration
Rinse Hold
increases.
• Set this option to prevent the laundry creases.
The related indicator comes on.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed. EXTRA RINSE
• The drum turns regularly to prevent the laundry With this option you can add some rinses to a
creases. washing programme.
• The door stays locked. You must drain the water Use this option for persons allergic to detergents
to unlock the door. and in areas where the water is soft.
To drain the water refer to ‘At the end The related indicator comes on.
of the programme’.
DELAY START
With this option you can delay the start of a
DRYING TIME
programme from 30 minutes to 20 hours.
With this option you can set the time for the fabrics The display shows the related indicator.
you have to dry. The display shows the set value.
Each time you press this touchpad the time value
increases by 5 minutes.
13
TIME SAVE Some programmes accept only one of
Press Time Save to decrease the programme time. these options.
You can select:
• QUICK: to wash items with daily soil.
• SUPER QUICK: to wash quickly items with
almost no soil.
SETTINGS
CHILD LOCK • To activate/deactivate this option press
With this option you can prevent that the children and at the same time until the indicator
play with the control panel. comes on/goes off.
• To activate/deactivate this option, press
ACOUSTIC SIGNALS
and at the same time until the indicator The acoustic signals operate when:
comes on/goes off.
• The programme is completed.
You can activate this option: • The appliance has a malfunction.
• After you press : the options and the To deactivate/activate the acoustic signals,
programme knob are locked. press and at the same time for 6 seconds.
• Before you press : the appliance cannot
start. If you deactivate the acoustic signals,
they continue operate when the
PERMANENT EXTRA RINSE appliance has a malfunction.
With this option you can permanently have an extra
rinse when you set a new programme.
14
LIQUID OR POWDER DETERGENT
1. Position A for powder
A detergent (factory setting).
DETERGENT COMPARTMENTS
Detergent compartment for pre-
wash phase. 5. Close the detergent
dispenser.
Detergent compartment for
washing phase.
Compartment for liquid additives
(fabric conditioner, starch).
Flap for powder or liquid deter-
gent.
15
• The door locks, the display shows the
When you use the liquid deter- indicator .
gent: • When the countdown is completed, the
• Do not use gelatinous or thick liq- programme starts automatically.
uid detergents.
• Do not put more liquid then the You can cancel or change the set of
maximum level. the delay start before you press the
• Do not set the prewash phase.
• Do not set the delay start. . To cancel the delay start:
• Press to set the appliance
to pause.
SETTING A PROGRAMME
• Press until the display
1. Turn the programme knob to switch the
appliance on and set the required programme: shows '.
• The indicator flashes. • Press again to start the
• The display shows the level of the Time programme immediately.
Manager, the programme duration and the
indicators of the phases of the programme. INTERRUPTING A PROGRAMME AND
2. If necessary, change the temperature and the CHANGING THE OPTIONS
spin speed or add available options. When you You can change only some options before they
activate an option, the indicator of the set operate.
option comes on.
1. Press .
If you set something incorrect, the The indicator flashes.
display shows the message . 2. Change the options.
3. Press again.
STARTING A PROGRAMME WITHOUT THE The programme continues.
DELAY START
CANCELLING A RUNNING PROGRAMME
Press .
1. Turn the programme knob to position to
• The indicator of stops to flash and
cancel the programme and to deactivate the
stays on.
appliance.
• The indicator starts to flash on the 2. Turn the programme knob again to activate the
display. appliance. Now, you can set a new washing
• The programme starts, the door locks, the programme.
display shows the indicator .
Before starting the new programme
• The drain pump can operate for a short time
the appliance could drain the water. In
when the appliance fills water.
this case, make sure that the detergent
After approximately 15 minutes from is still in the detergent compartment, if
the start of the programme: not fill the detergent again.
• The appliance adjusts automatically
the programme duration agree with OPENING THE DOOR
the laundry load.
• The display shows the new value. CAUTION! If the temperature and
level of the water in the drum are too
high and the drum still rotates, you
STARTING A PROGRAMME WITH THE DELAY
cannot open the door.
START
1. Press again and again until the display While a programme or the delay start operates, the
shows the delay you want to set. appliance door is locked and the display shows the
The related indicator comes on the display. indicator .
2. Press : Open the appliance door when the
programme or the delay start operates:
• The appliance starts the countdown.
16
1. Press to pause the appliance. 1. Press . The appliance drains the water and
2. Wait until the door lock indicator goes off. spins.
3. Open the door. 2. When the programme is completed, and the
door lock indicator goes off, you can open
4. Close the door and press again .
the door.
The programme or delay start continues to operate.
3. Turn the programme knob to position to
AT THE END OF THE PROGRAMME deactivate the appliance.
• The appliance stops automatically. The appliance drains and spins
• The acoustic signal operates (if it is activated). automatically after approximately 18
• In the display comes on. hours (except for Wool programme).
• The indicator of the goes off.
STAND-BY
• The door lock indicator goes off.
• You can open the door. Some minutes after the end of the washing
• Remove the laundry from the appliance. Make programme, if you do not deactivate the appliance,
sure that the drum is empty. the energy saving status activates.
• Close the water tap. The energy saving status decreases the energy
consumption when the appliance is on the stand
• Turn the programme knob to position to by.
deactivate the appliance.
• All indicators and the display go off.
• Keep the door ajar, to prevent the mildew and
odours. • The indicator of the flashes slowly
The washing programme is completed, but • Press one of the options to deactivate the
there is water in the drum: energy saving status.
• The drum turns regularly to prevent the creases
in the laundry. If you set a programme or an option
that ends with water in the drum, the
• The door lock indicator is on. The indicator energy saving status function doesn't
flashes. The door stays locked. activate to remind you to drain the
• You must drain the water to open the door. water.
To drain the water:
17
The display shows a time value, calculated on the
• The drying indicator starts to flash.
default load size. If the amount of your laundry is
• The display shows the door locked
more or less than the default size, the appliance
adjusts automatically the time value during the indicator .
cycle.
If you set only 10 minutes of drying,
2. Press to start the programme. the appliance performs only a cooling
The display shows the door locked indicator . phase.
If the laundry is not sufficient dry, set
The drying indicator starts to flash. again a short drying time.
You cannot set all dryness levels for
any type of laundry. END OF THE DRYING PROGRAMME
The appliance stops automatically.
TIMED DRYING • The acoustic signals operate (if they are active).
The laundry can also be dried with a manual timed • In the display comes on.
drying: • The indicator goes off.
1. Press again and again to set the time value • The last minutes of the drying cycle the
(see the «Programmes for timed drying» table). appliance performs a cooling and anti-crease
phase. The door is still locked.
• The display shows 10 minutes. Each time
you press this touchpad the time value When the door locked goes off in the display,
increases by 5 minutes. you can open the door.
• The display shows the set time value: for
1. Turn the programme knob to to deactivate
example . the appliance.
• After some seconds the display shows a After some minutes from the end of the programme,
new time value: . The appliance the energy saving function automatically
calculates also the duration of the anti- deactivates the appliance.
crease and the cooling phases. 2. Remove the laundry from the appliance.
2. Press to start the programme. Make sure that the drum is empty.
3. Keep the door ajar, to prevent mildew and
• The display shows regularly a new time
odours.
value.
4. Close the water tap.
18
The display shows the indicator . The time value
on the display is the duration of the washing + END OF THE PROGRAMME
drying cycles, calculated on a default load size. The appliance stops automatically. The acoustic
signals operate (if they are active).
To have a good drying the appliance For more information see "At the end of the drying
does not let you set a too low spin programme " of the previous chapter.
speed for the items to be washed and 1. Remove the laundry from the appliance.
dried.
Make sure that the drum is empty.
2. Press to start the programme. 2. Keep the door ajar to prevent mildew and
In the display the indicator of the set dryness level odours.
stays on. 3. Close the water tap.
The door locked indicator goes on. FLUFF IN THE FABRICS
The display shows regularly a new time value.
During the washing and/or drying phase, some
The last minutes of the drying cycle types of fabric, (sponge, wool, sweatshirt) could
the appliance performs the anti-crease release fluff.
and the cooling phases. The released fluff could stick to the fabrics during
the next cycle.
WASHING & TIMED DRYING To prevent the fluff in your laundry, we recommend
To have a good drying the appliance does not let that you:
you set a too low spin speed for the items to be • Do not wash dark fabrics after you have washed
washed and dried. and dried light coloured fabrics (new sponge,
wool, sweatshirt ) and the contrary.
1. Press to set the drying time value. The • Line dry this type of fabrics at open air when
display shows 10 minutes. they are washed the first time.
• Clean the drain filter.
The indicator comes on in the display. The
• After the drying phase, clean the empty drum,
display shows the set drying value time: for example
the gasket and the door with a wet cloth.
. After some seconds the display shows the
final time value , that is the total duration of HOW TO REMOVE THE FLUFF IN THE
the washing and drying cycles (washing + drying + GARMENTS
anti-crease + cooling phases). To remove the fluff inside the drum, set a special
programme:
If you set only 10 minutes of drying 1. Empty the drum.
after washing, the appliance calculates 2. Clean the drum, the gasket and the door with a
also the duration of the anti-crease wet cloth.
and the cooling phases. 3. Set the rinse programme.
2. Press to start the programme. 4. Press at the same time and to activate
the cleaning function until the display shows
In the display the indicator comes on. The door CLE.
is locked. The display shows regularly a new time
value. 5. Press to start the programme.
19
• Remove hard stains with a special detergent. • To use the correct quantity of detergent, check
• Wash and pre-treat heavy soil stains before the water hardness of your domestic system.
putting items in drum Refer to "Water hardness".
• Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or WATER HARDNESS
pillowcase. If the water hardness in your area is high or
• Do not wash laundry without hems or with cuts. moderate, we recommend that you use a water
Use a washing bag to wash small and/or softener for washing machines. In areas where the
delicate items (e.g. underwired bras, belts, water hardness is soft it is not necessary to use a
tights, etc. ). water softener.
• A very small load can cause balance problems To know the water hardness in your area, contact
with the spin phase. If this occurs, adjust your local water authority.
manually the items in the tub and start the spin
phase again. Use the correct quantity of the water softener.
Obey the instructions that you find on the
STUBBORN STAINS packaging of the product.
For some stains, water and detergent is not PREPARE THE DRYING CYCLE
sufficient.
• Open the water tap.
We recommend that you pre-treat these stains • Check if the drain hose is connected properly.
before you put the items in the appliance. Refer to installation chapter for more
Special stain removers are available. Use the information.
special stain remover that is applicable to the type • For the maximum laundry load of the drying
of stain and fabric. programmes, refer to the drying programmes
table.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially ITEMS NOT SUITABLE FOR DRYING
made for washing machines: Do not set a drying programme for this
– powder detergents for all types of fabric, laundry:
– powder detergents for delicate fabrics (40 • Synthetic curtains.
°C max) and woollens, • Pieces of clothing with metal inserts.
– liquid detergents, preferably for low • Nylon stockings.
temperature wash programmes (60 °C max) • Quilts.
for all types of fabric, or special for woollens • Bed covers.
only. • Duvets.
• Do not mix different types of detergents. • Anoraks.
• To help the environment, do not use more than • Sleeping bags.
the correct quantity of detergent. • Fabrics with residue of hair sprays, nail solvents
• Obey the instructions that you find on the on or similar.
packaging of these products. • Garments with foam-rubber or materials similar
• Use the correct products for the type and colour to foam-rubber.
of the fabric, the programme temperature and
the level of soil. GARMENT LABELS
• If your appliance does not have the detergent
When you dry the laundry, obey the indications on
dispenser with the flap device, add the liquid
the labels of the manufacturers:
detergents with a dosing ball (supplied by the
detergent's manufacturer). • = The item can be tumble dried
20
• type of laundry Experience will help you to dry the laundry better.
• weight of the load Take note of the duration of the cycles done before.
To avoid the static charge at the end of the drying
ADDITIONAL DRYING cycle:
If, at the end of the drying programme, the laundry 1. Use fabric conditioner in the washing cycle.
is still damp, set a short drying cycle again. 2. Use special fabric conditioner for tumble
dryers.
WARNING! To avoid creasing and When the drying programme is completed remove
shrinkage do not overdry the the laundry promptly.
laundry.
GENERAL TIPS
Refer to the «Drying programmes» table to find the
average drying times.
1 1 2 3 4
21
CLEANING THE DRAIN FILTER
WARNING! Do not clean the drain Repeat the steps 2 and 3 until the
filter if the water in the appliance is water stops flowing out.
hot.
1 2 3 4
2
2
1
180°
1
5 6 7 8
2 1
1 2 3 4
1
3 45°
20°
22
5. When the drain pump is empty, install the inlet
hose again. WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety chapters. • - The appliance does not drain the water.
• - The appliance door is open or not
closed correctly. Please check the door!
INTRODUCTION • - The mains supply is unstable. Wait until
The appliance does not start or it stops during the mains supply is stable.
operation. • - No communication between electronic
First try to find a solution to the problem (refer to elements of the appliance. Switch off and
the table). If the problem persists, contact the switch on again. The programme was not
Authorised Service Centre. finished properly or the appliance stopped too
With some problems, the acoustic signals early. If the alarm code appears again, contact
operate and the display shows an alarm the Authorised Service Centre.
code:
WARNING! Deactivate the appliance
• - The appliance does not fill with water before you do the checks.
properly. Start the appliance again by pressing
Start/Pause button. After 10 seconds the door
will be unlocked.
POSSIBLE FAILURES
• Make sure that the mains plug is connected to the mains socket.
• Make sure that the appliance door is closed.
• Make sure that there is not a damaged fuse in the fuse box.
The programme does not
• Make sure that the Start/Pause has been pressed.
start.
• If the delay start is set, cancel the setting or wait for the end of
countdown.
• Deactivate the Child Lock function if it is on.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
• Make sure that the water tap is not clogged.
The appliance does not fill
• Make sure that the filter of the inlet hose and the filter of the valve
with water properly.
are not clogged. Refer to “Care and cleaning”.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the connection of the water inlet hose is correct.
• Make sure that the connections of the water inlet hoses are correct.
The appliance does not fill • Make sure that the drain hose is in the correct position. The hose
with water and drain imme- may be too low. Refer to 'Installation instruction'.
diately.
23
Problem Possible solution
24
Problem Possible solution
After the check, activate the appliance. The programme continues from the point of interruption.
If the problem occurs again, contact the Authorised Service Centre.
If the display shows other alarm codes. Deactivate and activate the appliance. If the problem continues,
contact the Authorised Service Centre.
TECHNICAL DATA
Dimension Width/ Height/ Depth/ To- 600 mm/ 850 mm/ 522 mm/ 555 mm
tal depth
25
Electrical connection Voltage 230-240 V
Overall power 2200 W
Fuse 13 A
Frequency 50 Hz
Level of protection against ingress of solid particles and IPX4
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the with the symbol with the household waste.
packaging in relevant containers to recycle it. Help Return the product to your local recycling facility or
protect the environment and human health by contact your municipal office.
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
26
*
27
157024690-A-372018
WWW.ZANUSSI.COM/SHOP