Professional Documents
Culture Documents
All SPM CH05
All SPM CH05
CHAPTER 5 — CLEANING
TABLE OF CONTENTS
CLEANING
5-00-00
16 FEB 2007 Rev. 2 Page 1/2
BHT-ALL-SPM
CLEANING
5-1. CLEANING
CAUTION
NOTE
For detailed description of recommended CARPET CLEANING AGENTS SHOULD
cleaning agents, refer to Chapter 11. BE USED WITH CARE TO PREVENT
D A M A G E TO U N D E R LY I N G M E TA L
5-2. UPHOLSTERY S U R FA C E S . C A R P E T M U S T B E
REMOVED FROM HELICOPTER FOR
CLEANING. ALLOW CARPET TO DRY
PRIOR TO REINSTALLATION.
MATERIALS REQUIRED
Clean carpet using aliphatic naphtha (C-305) or any
Refer to Chapter 13 for specifications. good grade commercial drycleaning solvent.
MATERIALS REQUIRED
5-00-00
16 FEB 2007 Rev. 2 Page 3
BHT-ALL-SPM
1. Clean headliner and trim panel using aliphatic 3. Allow surfaces to air dry.
naphtha (C-305) or isopropyl alcohol (C-385), which
should be suitable for most materials. Test 4. Minor scratches may be reduced or removed by
inconspicuous area. using cleaner (C-330).
2. Finish cleanup with mild soap or detergent 5. Apply cleaner (C-330) with a clean soft cloth or
(C-355) and clean water. tissue in a circular motion until clean. Polish with
another clean, soft, cotton cloth.
5-5. PLASTIC AND GLASS
CAUTION
MATERIALS REQUIRED
5-00-00
Page 4 Rev. 3 19 JAN 2011 ECCN EAR99
BHT-ALL-SPM
CAUTION
MATERIALS REQUIRED
It is possible that high pressure washers will push C-304 Drycleaning Solvent
water underneath paint coatings through minute
cracks. Trapped water and soap will induce corrosion C-305 Aliphatic Naphtha
that will be unnoticed during a visual inspection. When
the damage appears, it might be too late to salvage
the affected part.
CAUTION
With this information, Bell Helicopter Textron wants to
place emphasis on the importance of the proper
procedures and advise operators to review their D O N O T R O TAT E B E A R I N G S W I T H
processes and equipment. COMPRESSED AIR.
5-00-00
ECCN EAR99 19 JAN 2011 Rev. 3 Page 5
BHT-ALL-SPM
MATERIALS REQUIRED
SOLVENTS MUST BE USED AT AMBIENT
Refer to Chapter 13 for specifications. TEMPERATURE. DO NOT USE STRONG
SOLVENTS, SUCH AS MEK, ACETONE,
NUMBER NOMENCLATURE LACQUER THINNER, ETC.
C-304 Drycleaning Solvent
3. Metal parts with adhesive bonded joints shall be
C-305 Aliphatic Naphtha cleaned with aliphatic naphtha (C-305), or drycleaning
solvent (C-304).
C-385 Isopropyl Alcohol
C-563 Perchloroethylene
CAUTION
1. Bare metals — no paint, adhesive, rubber etc.:
D O N O T S O A K R U B B E R PA R T S
a. Grease, oil, and corrosion preventive I N S O LV E N T. D O N O T VA P O R
compounds may be removed by vapor degreasing or DEGREASE AND DO NOT USE
solvent cleaning. CHLORINATED SOLVENTS SUCH AS,
TRI-CHLOROETHANE, TRICHLORO-
ETHYLENE AND PERCHLORO-
NOTE ETHYLENE. USE S O LV E N T S
SPARINGLY.
Make sure materials used are inhibited
vapor degreasing quality solvents.
4. Metal parts containing rubber such as,
elastomeric bearings, grease and oil seals, and rubber
b. Vapor degreasing may be accomplished by
boots shall be cleaned using aliphatic naphtha
using the following chlorinated solvent:
(C-305), isopropyl alcohol (C-385), or drycleaning
solvent (C-304).
(1) Perchloroethylene (C-563) — use at 248
to 252°F (120 to 122°C).
5-10. TITANIUM
NUMBER NOMENCLATURE
2. Painted metal parts:
C-304 Drycleaning Solvent
a. If part is to be stripped and repainted any
C-305 Aliphatic Naphtha
solvent suitable for bare metal may be used.
C-306 Toluene
b. If the painted part is to be installed without
stripping and repainting, solvents must be used at C-309 MEK
ambient temperature only. Also, solvents such as MEK
(C-309), acetone (C-316), lacquer thinner (C-206) and C-385 Isopropyl Alcohol
other strong solvents which attack the paint must be
C-395 Cleaner
avoided.
5-00-00
Page 6 Rev. 2 16 FEB 2007
BHT-ALL-SPM
NOTE
5-13. CLEANING OF FUNGUS
If vapor degreasing or chlorinated
hydrocarbons are used inadvertently, part
should be alkaline cleaned, rinsed and
dried, or scrubbed with soap and water, MATERIALS REQUIRED
rinsed and thoroughly dried, before
assembly. Refer to Chapter 13 for specifications.
NUMBER NOMENCLATURE
2. If paint or solid film lubricant must be removed
from titanium, use MEK (C-309) or nonchlorinated C-304 Drycleaning Solvent
paint remover.s
C-355 Detergent
5-11. TREATMENT OF FUNGUS
C-385 Isopropyl Alcohol
2. Baggage compartment
2. Remove debris or foreign matter with detergent
(C-355) and water.
3. Under the floor
4. Tailboom interior 3. Allow area to dry or wipe dry with clean cloth.
5. Behind sound deadening on the bulkheads and 4. Treat area of fungal growth with 99% isopropyl
overhead alcohol (C-385) and wipe with a clean cloth or sponge.
5-00-00
16 FEB 2007 Rev. 2 Page 7/8