Professional Documents
Culture Documents
Solarfref
Solarfref
CHAPTER ONE
1.0 Introduction
Solar radiation represents the largest energy flow entering the terrestrial ecosystem. After
reflection and absorption in the atmosphere, some 100,000TW hit the surface of Earth and
undergo conversion to all forms of energy used by humans, with the exception of nuclear,
geothermal, and tidal energy. This resource is enormous and corresponds to almost 6,000 fold
the current global consumption of primary energy 13.7 TW (Shafey, 1990). Thus, solar energy
has the potential of becoming a major component of a sustainable energy portfolio with
During the last decades, countries and companies are interested and investing in solar energy.
This kind of energy is abundant; however, it represents a low percentage comparing to the
current energy mix. The planet Earth can provide in only 90 minutes the needed sunlight that can
be used during a whole year (IEA, 2004). Hence, the field of the solar energy is growing very
fast improving with it a lot of technologies. Solar Photovoltaic Panels (PV’s) are the first thing
that can come to people’s mind while talking about solar energy. This technology is famous
because it is extremely modular, easy to install, and accessible (Aladdin, 2017). This project will
The current cost of solar technologies and their intermittent nature make them hardly competitive
on an energy market still dominated by cheap fossil fuels. From a scientific and technological
viewpoint, the great challenge is finding new solutions for solar energy systems to become less
capital intensive and more efficient. PV’s technology will advance in undeveloped nations like
Nigeria as the world is a global sphere for importing technologies (Andrews et al, 2013).
According to Kolhe et al (2015) Solar technology is on the whole more versatile and adaptable to
utilize for off grid and unstable grid territories, e.g. regionalized energy to ports, isle, towns,
residence, hospitals, water pump stations etc. Renewable energy projects are in general spent
within the territory, which means our investment stays at home to generate revenue and improve
Solar thermal technologies are reaching a mature stage of development and have the potential of
becoming competitive for large energy supply. Intermittency is being addressed with extended
research efforts in energy storage devices, such as batteries and other electric storage systems,
thermal storage, and the direct production of solar fuels (typically hydrogen). All these are
valuable routes for enhancing the competitiveness and performance of solar technologies. This
research effort is geared toward addressing the problem of implementing Low-cost and high-
Worldwide as well as Nigeria, the energy sector is one of the major reasons of climate change
especially with the use of fossil fuel. As a result, in order to guarantee the development of a more
sustainable and a functional planet we need to transform all our energy into a cleaner one to
promote a future power-driven by a full renewable energy (Keshner and Arya, 2004). Thus,
investing in renewable energy is beneficial for the local economy since Nigeria is experiencing a
Besides, Nigeria is extremely depending on petroleum, which means that Nigeria has a low
dependency on the renewable energy sector. Hence, the deployment of Solar Power will help
Nigeria to have diversified energy sources, which will contribute to the growth of NPA economy
and stability (Brabec et al, 2005). Therefore, promoting renewable energy can suggest a lot of
paybacks for the local economy in Nigeria since the infrastructure investments are localized and
the revenue stays related to the regional domain (Shaheen et al, 2005). The challenge of this
project is to power NPA with PV solar panels that are efficient and compare its cost with that of
electricity bills supplied to NPA before doing this, this project will take into account numerous
important factors such as the angle of inclination, the type of the inverters used, and the number
As it has been mentioned earlier, the aim of this research is to study the use of PV’s to power
NPA Port Harcourt that is a government agency. In terms of efficiency and savings, the detailed
i. Evaluate solar rays from sunshine duration data in Rivers State, Nigeria.
ii. Determine the power audit on NPA, Port Harcourt, Rivers State, Nigeria.
iii. Determine the number of PV panels/arrays, battery, other components and its cost
iv. Carry out comparative analysis between SPP and NPA electrical bill is calculated
This work covers the study of Solar PV, batteries, inverters, and Electric bill. Electrical Power
System Analysis Software (ETAP) is used to ascertain the number of parallels and series
arrangement of the solar power system to produce the needed power while Mathematical
laboratory (MATLAB) software is used to run the comparative analysis of SPP and electrical
bills of NPA, Port Harcourt. The panel cost, battery and inverter cost of the SPP is used in
carrying out a comparative analysis with the electrical bill and graphs showing their breakeven
point and total running cost will be generated and analyzed. It has become crucial for NPA to
implement a pioneering sustainable power supply with a correlated design which will reduce cost
of its operation.
According to Alrikabi (2014), about 8 million metric tons of CO2 is emitted as result of the use of
fossil fuels consistently. Around 126 billion naira (which is equal to US$ 984.38 million) deficit
in revenue is caused by power failure annually as reported by The Council for Renewable
Energy of Nigeria. Apart from the huge revenue deficit, (which could have been avoided by
using an alternative source of energy) in addition constant exposure of CO2 emitted as a result of
‘terrace generator’ brings about environmental and health hazards (Oyedepo, 2012).
confined to heavy reliance on generators for their official work and this generate a high running
cost the agency. If considered, this project will have an impact on NPA. For instance, it will
improve energy efficiency of NPA; it will boost NPA revenue and eradicate down time caused
Solar radiation is an electromagnetic wave emitted by the Sun’s surface that originates in the
bulk of the Sun where fusion reactions convert hydrogen atoms into helium. Every second
3.89*1026J of nuclear energy is released by the Sun’s core. This nuclear energy flux is rapidly
converted into thermal energy and transported toward the surface of the star where it is released
in the form of electromagnetic radiation. The power density emitted by the Sun is of the order of
64MW/m2 of which ~1370W/m2 reach the top of the Earth’s atmosphere with no significant
absorption in the space. The latter quantity is called the solar constant (Smil, 2004).
The spectral range of the solar radiation is very large and encompasses nanometric wavelengths
of gamma- and x-rays through metric wavelengths of radio waves. The energy flux is divided
unevenly among the three large spectral categories. Ultraviolet (UV) radiation (λ<400nm)
accounts for less than 9% of the total; visible light (VIS) (400nm<λ<700nm) for 39%; and
Radiation reaching the Earth’s surface is altered by a number of factors, namely the inclination
of the Earth’s axis and the atmosphere that causes both absorption and reflection of part of the
incoming radiation. The influence of all these elements on solar radiation is visible in the
ground-level spectrum, where the light absorption by the molecular elements of the atmosphere
is particularly evident. Accounting for absorption by the atmosphere, reflection from cloud tops,
oceans, and terrestrial surfaces, and rotation of the Earth (day/night cycles). The annual mean of
solar radiation reaching the surface is 170W/m2 for the oceans and 180W/m2 for the continents.
Of this, about 75% is direct light, the balance of which is scattered by air molecules, water vapor,
atmosphere and the terrestrial ecosystem. This quantity represents the upper limit to the work
obtainable from solar radiation conversion, a limit that is imposed by the 2nd law of
The 162PW of solar radiation reaching the Earth, 86PW hit its surface in the form of direct
(75%) and diffused light (25%). The energy quality of diffused radiation is lower (75.2% of
exergy content instead of 93.2% for direct light (Shafey and Ismail, 1990), with consequences on
the amount of work that can be extracted from it. 38PW hit the continents and a total exergy of
0.01TW is estimated to be destroyed during the collection and use of solar radiation for energy
services. This estimation includes the use of photovoltaics and solar thermal plants for the
production of electricity and hot water. Similar estimates are shown for wind energy (0.06TW),
ocean thermal gradient (not yet exploited for energy production), and hydroelectric energy
The market share of solar energy is still low. Current electricity generation from PVs is only of
the order of 2.6GW3 compared to 36.3GW for all renewable energies, hydroelectric power
excluded (IEA, 2005). Developed countries are steadily increasing their investments in solar
power plants, and IEA projections for 2030 give an enhancement of solar electricity generation
up to 13.6GW (80% of which will be from photovoltaics, and the rest (2.4GW) from solar
thermal plants). However, this amount will not exceed 6% of the total electricity production from
non-hydro renewable energies as shown in Fig 2.2. It is worth noting that passive solar
technologies for water heating, not included in these statistics, represent a fairly large amount of
power. IEA estimates a power production of 5.3GW in 2002 and an increase up to 46GW by
Fig 2.2 Current and projected non-hydro renewable electricity production for 2030 (in GW)
The higher capital cost of PV technologies compared to fossil fuels is a major barrier to large-
scale deployment of solar energy. Today’s price of electricity from solar energy, as reported by
the IEA, ranges from $0.35/kWh to $0.60/kWh for solar PV and from $0.085/kWh to
$0.135/kWh for solar thermal, compared to $0.045/kWh - $0.055/kWh for wind and $0.040/kWh
for natural gas. This cost range of solar energy is due to differences in the local isolation and to
the estimation of the Balance Of System (BOS) cost relative to specific applications (namely
elements determining the total price of PV technologies. Since the 1970’s research has been
exploring new processes for producing low-cost wafer silicon (both single crystal silicon, sc-Si,
and polycrystalline silicon, pc-Si), and the use of low-cost materials for thin-film PV
applications, such as amorphous silicon (α-Si), III-V compounds, CIGS, cadmium telluride
(CdTe), and more recently organic materials. The efficiency of thin-film laboratory cells has
increased steadily in the last 20 years (see Fig 2.3) and these technologies are believed to have
the potential of bringing down the cost of solar energy to $0.03/kWh - $0.05/kWh (Zweibel,
2004).
Manufacturing scale is another key requirement for decreasing the cost of solar technologies
since large-scale production lowers the cost of active materials and production. This is
demonstrated by the price drop that silicon PV modules experienced since the early 1980’s
following a progress ratio of 77% with cumulative production growing from 10MW to more than
1GW in 2000 (Parente et al, 2002). If the trend continues, the price of $1/W (~ $0.06/kWh) will
be reached when the cumulative production reaches 100GW, which in return will push further
Keshner and Arya (2004) suggested that price can reach an entirely through manufacturing scale,
without the need for any significant new invention. However, more research and development
will increase competitiveness of solar technologies. Design and technological innovations could
also decrease the cost of BOS components, and in particular of energy storage systems that
represent a major fraction of the total installation cost of systems where storage is required (up to
70-80% with batteries accounting for 30-40% (Hegedus and Luque, 2003). Such research efforts
exist in the field of thermal storage associated with solar thermal technologies (in particular
central receivers and parabolic troughs) and on new PV technologies with built-in storage
Yokohama (Miyasaka and Murakami, 2004). Additionally, cell stability and low-cost
encapsulation processes have also to be improved to maximize the lifetime of PV panels, with an
present-day p-n junction photovoltaic devices for reducing the cost of solar energy. They can be
deposited on lightweight, flexible and low-cost plastic substrates and thus have the potential to
The manufacturing cost for OPVs can be very low using large-throughput roll-to-roll
manufacturing technology enabled with printable semiconductors and low-cost materials such as
plastic substrates and polymer alternatives to Transparent Conducting Oxide (TCO) electrodes.
Concerning BOS costs, packaging will remain a major concern due to the sensitivity of organic
materials to oxygen and water vapor. Cost projections for electricity from organic photovoltaics
based on the use of printing techniques and decrease of material cost with scaleup, are
Over the past 30 years, solar cell efficiencies have continuously improved for all technologies
(Green et al, 2006). Research on desensitized solar cells (DSSCs) and organic solar cells (OSCs)
began only during the last decade (Xue et al, 2004). Despite the notable progress made in the
improvement of the efficiencies of all these technologies, achieved values are still far from the
thermodynamic efficiency limits of ~31% for single junctions, 50% for 3-cell stacks, impurity
PVs, or up- and down converters, and 54-68% for hot carrier- or impact ionization-based devices
(Green, 2003). Furthermore, the efficiencies of commercial (or even the best prototype) modules
are only about 50% to 65% of these “champion” cells (Green et al, 2006).
The solar-to-electric efficiency of solar thermal technologies varies largely depending upon the
solar flux concentration factor, the temperature of the thermal intermediary, and the efficiency of
the thermal cycle for the production of mechanical work and electricity. Parabolic troughs and
power towers reach peak efficiencies of about 20%. Dish-Stirling systems are the most efficient,
with ~30% solar-to-electric demonstrated efficiency. The performance of these systems is highly
influenced by the plant availability. In the case of parabolic troughs and power towers, thermal
storage increases the annual capacity factor from typically 20% to 50% and 75%, respectively
(King, 2005).
Solar energy is promoted as a sustainable energy supply technology because of the renewable
nature of solar radiation and the ability of solar energy conversion systems to generate
greenhouse gas-free electricity during their lifetime. However, the energy requirement and the
environmental impact of PV module manufacture can be further reduced, even though recent
analysis of the energy and carbon cycles for PV technologies recognized that strong
improvements were made both in terms of energy and carbon paybacks (Xue et al, 2004).
Energy payback calculations are not straightforward because today’s PV industry usually
recrystallizes silicon recycled from the semiconductor industry. Calculations reported in 2000 by
Alsema give estimates of the life-cycle energy requirement embodied in, respectively, frameless
2010 the requirement of electric energy for these PV technologies is forecasted to decrease to
890kWh/m2 (5.6kWh/W) and 720kWh/m2 (4.7kWh/W assuming 12% conversion efficiency and
190W/m2 of sunlight energy flux (Alsema, 2000). This results in a payback time of about 4.5
years for near-term pc-Si PV modules. As illustrated in Fig 2.5, more recent estimates of the
energy payback time for polycrystalline silicon (pc-Si) technologies are about two years
For thin films, the energy required to deposit the active layer is negligible compared to forming
crystalline silicon wafers. Instead, the major energy sink is the energy embodied in the glass or
stainless steel substrate, the film deposition process, and facility operation. These energy costs
are similar for all thin-film technologies (CIGS, CdTe, α-Si), varying only in the film deposition
processes. An estimate for the frameless α-Si module electricity requirement is 330kWh/m2
conditions) and 190W/m2 of available sunlight flux, the payback time for current thin-film PV
systems is around 2.8 years. More recent estimates give shorter payback times for thin-film
frames represent a non-negligible fraction of the total energy requirement (Keoleian and Lewis,
1997). For a rooftop-mounted system another 120 kWh/m2 should be added to the overall
lifecycle energy requirement, resulting in a payback time of about 3.5 years. Support structures
for ground-mounted systems would add about another year to the payback period. Despite the
wide range of payback times that can be found in the literature, all estimates remain higher than
It is interesting to note that analysis of fossil-fuel energy production has suggested that it has
similar energy payback periods to PV technologies if the costs for mining, transportation,
refining, and construction are included in the calculation of the life cycle of fossil fuels (Dones
Carbon payback The CO2 savings (other pollutants are also avoided, including NOx, SO2, and
particulates) from displacing fossil fuels with photovoltaic systems depend upon the regional
fossil fuels mix and the solar irradiance; values range from 270g to >1050g of CO2/kWh. The
world average is about 660g of CO2/kWh. Assuming an average of 5.5 hours of sunlight per day,
a 1kW PV panel would give a yearly CO2 savings of 1330kg (McGehee and Heeger, 2000).
The CO2 payback time from avoided emissions also depends on the local energy mix and the
panel efficiency. Assuming an energy cost for a sc-Si panel of 600kWh/m2 and the average of
660g of CO2/kWh, the manufacture of a 1m2 panel produces ~400 kg of CO2. If we assume
12% efficiency and a solar irradiance of 1kW/m2, it takes 3300kg of CO2 to produce a 1kW PV
plant, which is paid back in avoided emissions at 1330kg/year for a total time of 2.5 years. For a
more detailed analysis.) Higher cell efficiencies lower both the energy and CO2 payback time, as
do manufacturing techniques that are more energy efficient (Fthenakis and Zweibel, 2003).
Safety and environmental issues The major safety and environmental issues related to the
manufacture of photovoltaics are (1) the safe handling of gases used for surface treatment or the
growth of thin films (e.g. AsH3, SiH4, GeH4, PH3, B2H6, and H2Se), and (2) the toxicity of
some semiconductor components (e.g. Cd). It is generally believed that safe usage of potentially
hazardous materials in PV manufacturing is possible and that the electronics industry has already
made significant progress in dealing with similar materials. Nevertheless, further investigation
could lead to the replacement of toxic components and thus eliminate most of the concerns about
technologies, to conserve rare minerals such as tellurium, and to reduce the energy requirement
of PV manufacturing. Recycling cost estimates are 0.2-0.4$/W for CdTe modules (at a process
scale of 2MW), and about 0.13$/W for c-Si cells at an operational scale of 150,000 c-Si cells per
Fig 2.6. Solar energy conversion paths and technologies considered in this survey.
A wide variety of solar technologies have the potential to become a large component of the
future energy portfolio. Passive technologies are used for indoor lighting and heating of
buildings and water for domestic use. Also, various active technologies are used to convert solar
energy into various energy carriers for further utilization. Photovoltaics directly convert photon
greater than their bandgap to promote energy carriers into their conduction band. Electron-hole
pairs, or excitons for organic semiconductors, are subsequently separated and charges are
Solar thermal technologies convert the energy of direct light into thermal energy using
concentrator devices. These systems reach temperatures of several hundred degrees with high
associated exergy. Electricity can then be produced using various strategies including thermal
engines (e.g. Stirling engines) and alternators, direct electron extraction from thermionic devices,
through thermophotovoltaic devices, and conversion of the kinetic energy of ionized gases
convert solar energy into chemical energy for energy storage in the form of chemical fuels,
particularly hydrogen. Among the most significant processes for hydrogen production are direct
solar water splitting in photoelectrochemical cells or various thermochemical cycles such as the
This document focuses on active solar technologies which are organized according to the energy
conversion paths that they use to convert the energy of photons into a usable energy form:
heat-to-chemical energy (see Fig. 6). This analysis focuses on the fundamental physical
processes that govern the operation of the solar devices with the intent of identifying common
trends or synergies between different technologies that could help identify novel research
opportunities.
PHOTOVOTAIC CELLS
Photovoltaic systems are solar energy supply systems, which convert sunlight directly to
electricity. The chief component in PV systems is the solar panel which is formed by putting
together several PV cells. Putting together several PV cells forms a PV module; several modules
form arrays and several arrays form panels. The modular nature of PV cells makes it possible for
them to be used for a wide range of power applications ranging from a few milliwatts in wrist
watches and scientific calculators to several megawatts in central power stations. Solar cells are
usually made of semiconductor materials such as silicon, gallium arsenide, cadmium telluride or
copper indium diselenide (DGS, 2008). Solar cells come in two major forms based on the nature
of the material used in their production. The two main forms are crystalline solar cells and thin
film solar cells. Crystalline solar cells, so far, have the highest conversion efficiencies when it
comes to photovoltaic cells and the main types are monocrystalline and polycrystalline cells
(DGS, 2008). Thin film cells, although less efficient than crystalline silicon offer greater promise
for large-scale power generation because of ease of mass-production and lower materials cost.
The commonest example of thin film cells is the amorphous silicon cell (DGS, 2008).
Photovoltaic systems can be grouped into two main groups; namely off-grid systems and grid-
connected systems (DGS, 2008). Off-Grid Systems Off-grid PV systems, as the name implies,
are systems that are not connected to the public electricity grid. These systems require an energy
storage system for the energy generated because the energy generated is not usually required at
the same time as it is generated (DGS, 2008). In other words, solar energy is available during the
day, but the lights in a stand-alone solar lighting system are used at night so the solar energy
generated during the day must be stored for use in the night. They are mostly used in areas where
it is not possible to install an electricity supply from the mains utility grid, or where this is not
cost-effective or desirable. They are therefore preferable for developing countries where vast
areas are still frequently not supplied by an electrical grid. Off-grid systems are usually
employed in the following applications; consumer applications such as watches and scientific
calculators, industrial applications such as telecommunications and traffic signs and remote
habitations such as solar home systems and water pumping applications. A typical off-grid
system comprises the following main components: • Solar PV Modules: these convert sunlight
directly to electricity. • Charge Controllers: manage the charging and discharging of the batteries
in order to maximize their lifetimes and minimize operational problems • Battery or Battery
Bank: Stores the energy generated by the PV modules • Inverter: converts the DC current
generated by the solar PV modules to AC current for AC consumer load (DGS, 2008). Grid-
grid usually the public electricity grid and feed power directly into the grid. These systems are
rooftop PV generators, where the PV systems are mounted on rooftops of buildings and
incorporated into the building’s integrated system (DGS, 2008). In the case of residential or
building mounted grid connected PV systems, the electricity demand of the building is served by
the PV system and the excess is fed into the grid; their capacities are usually in the lower range
converts the DC current generated by the solar PV modules to AC current for the utility grid. •
capacities ranging from the higher kilowatts to the megawatt range (DGS, 2008). Solar PV is
currently the fastest growing power generation technology in the world with about 38,584MW
capacity installed in the year 2010. In all, Europe alone contributes about 70% of the total
installed capacity of PV systems with North America, Japan, China and Australia following in
that order (EPIA et al 2010). Grid-connected systems make up the majority of these figures and
this is as a result of favourable incentives such as feed-in tariff schemes, tax rebates and
investment subsidies. (EPIA et al, 2010; REN21, 2011) The solar PV industry has also seen
commercial scale. This improvement in technology and the continuous growth of the PV market
has led to drastic reduction in the cost of solar PV systems on the global market (EPIA et al,
2010). The situation on the African continent is however not encouraging, with Africa
contributing less than 1% of the world’s installed solar PV systems (installed capacity of
163MW as at the end of 2010), in spite of the huge solar energy potential available to the
continent (BrewHammond et al., 2008). This is as a result of the lack of policy instruments that
help promote renewable energy technologies in general and also the very high initial capital
involved in developing solar PV systems. Grid-connected solar PV systems are not that popular
in Africa since most solar PV applications are employed in off-grid rural electrification projects
to rural communities (for lighting, educational and health applications) that are far from the
national grid. (EPIA et al, 2010). The situation in Ghana is not so different from the rest of the
Africa continent with most solar PV systems employed in off-grid rural electrification projects.
The Energy Commission of Ghana is however leading efforts to promote grid-connected solar
PV in the country by partly sponsoring individuals and institutions to install grid connected solar
PV and wind energy systems with capacities not less than 75kWp. The commission is also
spearheading development of a renewable energy law for the country which will provide
incentives for the development of renewable energy technologies in the country including grid-
connected solar PV. The Energy Commission and KNUST both have installed 4kWp grid-
connected solar PV systems each, donated by the German state of North Rhine Westphalia to aid
in research into grid-connected solar PV systems (MoE, 2010; Energy Commission, 2011).
References
IEA, “World Energy Outlook 2004”, International Energy Agency, Paris, IEA/OECD,
2004
Andrews, S. P., Zhang, S and Zhoa, X. (2013). A Critical Analysis of China Policy
Approach to Renewable Energy. Interactions Between Renewable Energy Policy and
Renewable Industrial Policy, (pp. 342-353). china.
Aladdin Solar, LLC. PV System Types: Grid-Tied, Battery Backup, Off-Grid, Direct PV.
N.p., n.d. Web. 13 Apr. 2017
Alrikabi, N. (2014). Renewable Energy Types. Journal of Clean Energy Technology, 61-
64.
Alsema E.A., “Energy pay-back time and CO2 emissions of PV systems”, Prog.
Photovolt. Res. Appl., 8(1), 2000, p. 17
Brabec C., Hauch J.A., Schilinsky P., Waldauf C., “Production aspects of organic
photovoltaics and their impact on the commercialization of devices”, MRS Bulletin, 30,
2005, p. 50 (www.mrs.org/publications/bulletin)
Keshner M.S and Arya R., ”Study of potential cost reductions resulting from super-large-
scale manufacturing of PV modules”, NREL report NREL/SR-520-36846, 2004
Shaheen.S.E., Ginley D.S and Jabbour G.E., “Organic-based photovoltaics: toward low-
cost power generation”, MRS Bulletin, 30, 2005, p. 10
(www.mrs.org/publications/bulletin)
Oyedepo.S.O., (2012). Energy and Sustainable Development in Nigeria: the way forward.
Energy, Sustainability and Society, Vol2 pp 1.
Smil.V., “Energies”, ed. The MIT Press, Cambridge (MA), 1999 Renewable resource
data center (http://rredc.nrel.gov/)
Shafey.H.M and Ismail.M., “Thermodynamics of the conversion of solar radiation”,
Journal of Solar Energy Engineering, 112, 1990, p. 140
Hermann.W., “Quantifying global exergy resources”, Energy, 31(12), 2006, p. 1349
IEA International Statistics 2005 (http://www.iea-pvps.org/isr/index.htm)
IEA, “World Energy Outlook 2004”, International Energy Agency, Paris, IEA/OECD,
2004
Zweibel.K., “PV as a major source of global electricity”, Conference at the University of
Toledo (OH), 2/24/2004 (http://www.greenenergyohio.org/page.cfm?pageId=500) [
Parente.V., Goldemberg.J and Zilles.R., ”Comments on experience curves for PV
modules”, Prog. Photovolt. Res. Appl., 10(8), 2002, p. 571
Fthenakis.V.M and Lee J.C., “The impact of photovoltaics on CO2 emissions' reduction
in the US”, The World Resource Review, 10(3), 1998, p. 435
Hegedus.S.S and Luque.A., “Handbook of Photovoltaic Science and Engineering”, John
Wiley & Sons, Ltd, 2003
Miyasaka.T and Murakami.T.N., “The photocapacitor: an efficient self-charging
capacitor for direct storage of solar energy”, Appl. Phys. Lett. 85(17), 2004, p. 3932
Shaheen.S.E., Ginley.D.S and Jabbour.G.E., “Organic-based photovoltaics: toward low-
cost power generation”, MRS Bulletin, 30, 2005, p. 10 (www.mrs.org/publications/
bulletin)
Green.M.A., Emery.K., King.D.L., Hishikawa.Y and Warta.W., “Solar cell efficiency
tables (version 28)”, Prog. Photovolt. Res. Appl., 14(5), 2006, p. 455
King.R.R., “Pathways to 40%-efficienct concentrator photovoltaics”, to be published in
the Proc. of the 20th European Photovoltaic Conference, Barcelona, Spain, June 2005
Grätzel.M., “Perspectives for dye-sensitized nanocrystalline solar cells”, Prog. Photovolt.
Res. Appl., 8(1), 2000, p. 171
Xue.J., Uchida.S., Rand.B.P and Forrest.S.R., “Asymmetric tandem organic photovoltaic
cells with hybrid planar-mixed molecular heterojunctions”, Appl. Phys. Lett., 85(23),
2004, p. 5757
Green.M.A., “Third generation photovoltaics: advanced solar energy conversion”, ed.
Springer, 2003
Fthenakis.V and Alsema.E, “Photovoltaics energy payback times, greenhouse gas
emissions and external costs: 2004-early 2005 status”, Prog. Photovolt. Res. Appl., 14(3),
2006, p. 275
Keoleian G.A and Lewis G. McD, “Application of life-cycle energy analysis to
photovoltaic module design”, Prog. Photovolt. Res. Appl., 5(4), 1997, p. 287
Turner J.A., “A realizable renewable energy future”, Science, 285, 1999, p. 687
R. Dones, R. Frischknecht, “Life cycle assessment of photovoltaic systems: results of
Swiss studies on energy chains”, in “Environmental Aspects of PV Power Systems”,
Appendix B-9, Utrecht, The Netherlands, Utrecht University Report Number 97072,
1997
M.D. McGehee, A.J. Heeger, “Semiconducting (conjugated) polymers as materials for
solid-state lasers”, Adv. Mater., 12(22), 2000, p. 1655
V. Fthenakis, K. Zweibel, “CdTe photovoltaics: real and perceived environmental, health
and safety risks”, NCPV Progr. Rev. Meeting, March 25, 2003
(http://www.nrel.gov/cdte/pdfs/ncpv_cdte.pdf)
V. Fthenakis, P. Moskovitz, K. Zweibel, “Photovoltaics and the environment – Workshop
Summary”, Keystone (CO), 1998 (http://www.pv.bnl.gov/keystone.htm)
F. Lenzmann, “Extremely Thin Absorbers: EU Project Overview”, GCEP Solar
Workshop, Stanford University (CA), 2004
(http://gcep.stanford.edu/pdfs/solar_workshop_10_04/Solar Lenzmann2004.pdf)