Professional Documents
Culture Documents
KDC-W3041
KDC-W312
KDC-W241
KDC-241
INSTRUCTION MANUAL
© B64-3903-10/01 (EW/E2W)
2 | KDC-W3041/KDC-W312/KDC-W241/KDC-241
English | 3
[VOL] [SRC] [1] [2] [3] [4] [5] [6] [TI]/[AUTO] [B.BOOST]
¤
• The faceplate is a precision piece of equipment and can be
damaged by shocks or jolts.
• Keep the faceplate in its faceplate case while detached.
• Do not place the faceplate (and the faceplate case) in areas
exposed to direct sunlight, excessive heat or humidity. Also
avoid places with too much dust or the possibility of water
splashing.
• To prevent deterioration, do not touch the terminals of the
unit or faceplate with your fingers.
4 | KDC-W3041/KDC-W312/KDC-W241/KDC-241
English | 5
Audio Control ⁄
• Volume offset: Sets each source’s volume as a difference
1 Select the source to adjust from the basic volume.
Press the [SRC] button.
4 Adjust the Audio setup item
2 Enter Audio Control mode Turn the [VOL] knob.
Press the [VOL] knob.
5 Exit Audio Setup mode
3 Select the Audio item to adjust Press the [VOL] knob for at least 1 second.
Press the [VOL] knob.
Adjustment Item Display Range
Subwoofer level* “SW L” –15 — +15
System Q “NATURAL”/ Natural/Rock/Pops/Easy/Top Speaker Setting
“ROCK”/“POPS”/ 40/Jazz/User setting Fine-tuning so that the System Q value is optimal
“EASY”/“TOP40”/
“JAZZ”/“USER” when setting the speaker type.
Bass level “BAS L” –8 — +8
1 Enter Standby
Middle level “MID L” –8 — +8
Press the [SRC] button.
Treble level “TRE L” –8 — +8
Select the “STANDBY” display.
Balance “BAL” Left 15 — Right 15
Fader “FAD” Rear 15 — Front 15 2 Enter Speaker Setting mode
Exit Audio Control mode (Volume control mode) Press the [VOL] knob.
*Function of KDC-W3041/W312. 3 Select the Speaker type
⁄ Turn the [VOL] knob.
• “USER”: This appears when Bass level, Middle level, and Speaker type Display
Treble level are adjusted. When “USER” is selected, OFF “SP OFF”
these levels are recalled. For 5 & 4 in. speaker “SP 5/4”
4 Adjust the Audio item For 6 & 6x9 in. speaker “SP 6*9/6”
Turn the [VOL] knob. For the OEM speaker “SP OEM”
Switching Display
Audio Setup
Changing the information displayed.
Setting the Sound system.
1 Enter Switching Display mode
1 Select the source to adjust Press the center of the Control knob for at least
Press the [SRC] button. 1 second.
2 Enter Audio Setup mode “DISP SEL” is displayed.
Press the [VOL] knob for at least 1 second. 2 Select the Display item
3 Select the Audio Setup item to adjust Press the right or left side of the Control knob.
Press the [VOL] knob. In Tuner source
Adjustment Item Display Range Information Display
Low Pass Filter* “LPF” 80/120/160/Through Hz Program Service name or Frequency “FREQ”/ “FREQ/PS”
Volume offset “V-OFF” –8 — ±0 (AUX: -8 — +8) Radio text, Program Service name or Frequency* “R-TEXT”
*Function of KDC-W3041/W312. Clock “CLOCK”
* This is not displayed on the KDC-W241/KDC-241.
6 | KDC-W3041/KDC-W312/KDC-W241/KDC-241
English | 7
Selecting the Program Type and searching for a 3 Search for the selected Program Type station
station. Press the right or left side of the Control knob.
⁄
1 Enter PTY mode • When the selected Program Type is not found, “NO PTY”
Press the center of the Control knob. is displayed. Select another Program Type.
During PTY mode the “PTY” indicator is ON.
4 Exit PTY mode
⁄ Press the center of the Control knob.
• This function cannot be used during a traffic bulletin or
AM reception.
8 | KDC-W3041/KDC-W312/KDC-W241/KDC-241
Function of KDC-W3041/KDC-W312/KDC-W241
Function of Audio file
Folder Select
Quickly selecting the folder you want to hear.
English | 9
10 | KDC-W3041/KDC-W312/KDC-W241/KDC-241
Selecting the display when changing to Auxiliary 2 Set the Demonstration mode
input source. Press the center of the Control knob for at least
2 seconds.
1 Select Auxiliary input source Each time you press the knob at least 2 seconds,
Press the [SRC] button. the Demonstration mode alternates between the
Select the “AUX” display. settings shown in the table below.
2 Enter Menu mode Display Setting
Press the [B.BOOST] button for at least 1 “DEMO ON” The Demonstration mode function is ON.
second. “DEMO OFF” Exit Demonstration mode (Normal mode).
“MENU” is displayed.
3 Select Auxiliary input display setting mode
Press the top or bottom side of the Control
knob.
Select the “NAME SET” display.
4 Enter Auxiliary input display setting mode
Press the center of the Control knob for at least
1 second.
The presently selected Auxiliary input display is
displayed.
5 Select the Auxiliary input display
Press the right or left side of the Control knob.
Each time you push the knob, the display alternates
as listed below.
• “AUX”
• “DVD”
• “PORTABLE”
• “GAME”
• “VIDEO”
• “TV”
6 Exit Auxiliary input display setting mode
Press the [B.BOOST] button.
⁄
• When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
English | 11