Professional Documents
Culture Documents
Manual de Serviço BLU Neo 4.5 PDF
Manual de Serviço BLU Neo 4.5 PDF
5
Service Manual
D507B Repair Guide
Contents
Contents ................................................................................................................................. 2
1. Introduction ......................................................................................................................... 3
1. Introduction
1.1 Objective
The manual is not a general publication but only edited for experienced technician. The
main purpose is to provide basic foundation for the electrical & mechanical maintenance.
2. Technology summarize
2.1 Description of main board component map
D507B Repair Guide
Platform Features:
◆ General:
1) Smartphone,3 MCU subsystems architecture
2) eMMC boot support
3) Supports LPDDR-1/LPDDR-2/LPDDR-3/PD-DDR3
◆ AP MCU subsystem
1) Dual-core ARM Cortex-A7 MP Core operating at 1.3GHz
2) NEON multimedia processing engine with SIMDv2/VFPv4 ISA support
3) 32KB L1 I-cache and 32KB L1 D-cache
4) 256KB unified L2 cache
5) DVFS technology with adaptive operating voltage from 1.05V to 1.26V
◆ MD MCU subsystem
1) ARM Cortex-R4 processor with maximum 480MHz operation frequency
2) 32KB I-cache, 16KB D-cache
3) 256KB TCM (tightly-coupled memory)
4) DSP for running modem/voice tasks, with maximum 245.76MHz operation frequency
5) High-performance AXI and AHB bus
6) General DMA engine and dedicated DMA channels for peripheral data transfer
7) Watchdog timer for system error recovery
8) Power management for clock gating control
◆ MD external interfaces
1) Supports dual SIM/USIM interface
2) Interface pins with RF and radio-related peripherals
D507B Repair Guide
3. Trouble Shooting
3.1 Fail to startup/power on
The following conditions may cause boot fail: battery low, battery connector is damaged or
bad welding, components bad weld/short-circuit or damaged
First, change a fully charged battery test, still startup fail, check battery connector ok or not,
if connector damaged change a new one;
Second, connect to DC power supply, if the boot process is no current, we should check
power key solder ok or not;
Third, if the boot current is very small and cannot maintain ,connect the power on test point
to GND, then check below voltage in sequence, BBWAKEUP , VRTC ,
VPROC(VCORE,VSRAM),VSYS,VIO18/VEMC3V3,VA28/VIO28,VM,VUSB,VMC/VMCH,
VTCXO, RESETB ok not.
Fourth, if the current stay in 80mA, we should check the circuit around flash, when CPU
calling program from flash fail, the current will stay in 80mA, re-download the software or
change a new flash or CPU.
Fail to power on
N
Check if the battery Change
is OK. battery
Y
N Resold
Check if battery
connects solder ok connect
Re-download Y OK
Software
N
Y
Resold or replace OK
U1501
N
Y
Resold or replace OK
U1200
D507B Repair Guide
No charge
N
Check J1702 Change a new
solder OK or not? one
Y
N
Change T2020
Check T2020 &
or C2020
C2020
Check B2020, N
Change related
B2021 ,U1400ok or component
not?
N
Check U1420 Hot or change
U1420
D507B Repair Guide
No display
N
Is the LCM well?
Change LCM
Y
U1850 Change
reverse or U1850
damaged
L1850, D1850 Y
NC or not Add L1850 or D1850
Change or Y Change
re-solder U1200
U1200
OK
D507B Repair Guide
Y
Check receiver and Check RF
mic ok or not?
N
N Check
Rework Check
Related Related Rework
uncorrected uncorrected
R C TVS? R, C, TVS?
component Y component
Y
Y
N N
Hot or change Check Check Hot or change
new one U1200? U1200? new one
D507B Repair Guide
No sound
N
Is speaker OK? Replace
Speaker
Y
Are B1601, B1600
NC or not? ADD B1600, B1601
N
Check T1912, Re-solder uncorrected
T1913 ok or not? component
Y
N
Check U1420 Hot or change U1420
D507B Repair Guide
No sound in
earphone
N
Is earphone Replace
connector OK? earphone
Is J1620 N
Re-solder J1620
soldering well?
Related R, N Re-solder
C right? uncorrected R C
Hot or
OK
change
U1420
D507B Repair Guide
N
Supply 3.3V for motor, Change a
test motor can work or new Motor
not
Check VIBR_PMU ok or N
Change uncorrected
not, Check SUB PCB component or sub
reverses or not PCB
Hot U1420 or OK
Change a new one
D507B Repair Guide
N
Re-solder or
Is key switch soldering
change new
OK?
one
Y
Check U1200 Re-sold or change
U1200
D507B Repair Guide
Touch Pin is N
Clean SIM socket
clean?
Y
Change a new SIM is damaged.
SIM to try Replace it
N
Is SIM socket Change a new one.
good?
N
Check if VSIM1/ Change U1420
VSIM2 are OK?
N
Could it power To the part fails to power on
on?
Y
Could it Re-plug USB cable,
download? re-flash IMEI
Re-solder or N
Re-solder or change
change PMU
U1420
U1420.
OK
D507B Repair Guide
Camera fail
N
Is camera connector Re-solder or
soldering well? change new
one
Check camera ok or N
Change a new
not? camera
Y T-F card is
Change a new
damaged. Replace
TF-card to test
it
N
Check T flash Re-solder it or
card socket change new one
ok or not?
N
Check TVS
Solder it correct
reverse or not?
N
Check VDD Hot U1420 or
OK or not? change new
one
N Hot U1200
Check each
signal OK or not? or change
new one
D507B Repair Guide