Professional Documents
Culture Documents
Issue 05
Date 2018-11-07
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
1 Change History.............................................................................................................................. 1
1.1 eRAN13.1 05 (2018-11-07)............................................................................................................................................1
1.2 eRAN13.1 04 (2018-08-27)............................................................................................................................................2
1.3 eRAN13.1 03 (2018-06-30)............................................................................................................................................2
1.4 eRAN13.1 02 (2018-05-25)............................................................................................................................................3
1.5 eRAN13.1 01 (2018-04-10)............................................................................................................................................3
1.6 eRAN13.1 Draft A (2018-01-15) (FDD)........................................................................................................................4
3 General Principles......................................................................................................................... 8
3.1 Overview........................................................................................................................................................................ 8
3.2 Network Architecture..................................................................................................................................................... 9
9.3.4 Others.......................................................................................................................................................................143
9.4 Operation and Maintenance........................................................................................................................................143
9.4.1 Data Configuration.................................................................................................................................................. 143
9.4.1.1 Data Preparation................................................................................................................................................... 143
9.4.1.2 Using MML Commands....................................................................................................................................... 144
9.4.1.3 Using the CME..................................................................................................................................................... 144
9.4.2 Activation Verification............................................................................................................................................ 144
9.4.3 Network Monitoring................................................................................................................................................ 145
12 Parameters................................................................................................................................. 163
13 Counters.................................................................................................................................... 287
14 Glossary..................................................................................................................................... 558
15 Reference Documents............................................................................................................. 559
1 Change History
This chapter describes changes not included in the "Parameters", "Counters", "Glossary", and
"Reference Documents" chapters. These changes include:
l Technical changes
Changes in functions and their corresponding parameters
l Editorial changes
Improvements or revisions to the documentation
Technical Changes
Change Description Parameter RAT Base Station
Change Model
Editorial Changes
None
Technical Changes
None
Editorial Changes
Revised descriptions in this document.
Technical Changes
None
Editorial Changes
For FDD, there is no change.
Technical Changes
None
Editorial Changes
Revised descriptions in 4.1.3.3 Fairness Guarantee for Roaming.
Technical Changes
Change Description Parameter RAT Base Station
Change Model
Editorial Changes
None
Technical Changes
Change Description Parameter Change Base Station Model
Added support for sharing of Added the LicenseSharingPo- l 3900 and 5900
RRC_CONNECTED UE licy.UserNumSharingGrou- series base stations
resources within an pId parameter. l DBS3900
RRC_CONNECTED UE LampSite and
number sharing group. For DBS5900
details, see 4 RAN Sharing LampSite
with Common Carrier and 9
Fair User Sharing (FDD). l BTS3912E
l BTS3911E
l BTS3203E
l BTS3202E
Editorial Changes
Reorganized this document using a new template.
3 General Principles
3.1 Overview
When operators deploy their own networks, they have to pay expensive spectrum license fees
and high network deployment costs. They need to deploy sites within a short period to
provide proper network coverage. Huawei proposes RAN sharing to help operators tackle
with these challenges.
RAN sharing is the sharing of network infrastructure or network equipment among multiple
operators or with third parties.
The infrastructure that can be shared includes sites, equipment rooms, towers, and power
supplies. Network equipment that can be shared includes base stations, transmission
equipment, and core network (CN) equipment.
The following is a sample list of RAN sharing modes:
l Operators share the infrastructure of a site.
l Mobile network operators (MNOs) share their RANs and CNs with mobile virtual
network operators (MVNOs).
l Operators share network resources by allowing national or international roaming.
l Operators jointly invest in the construction of a single wireless network.
Huawei eNodeBs support the following modes:
l Independent operator mode
l RAN sharing with common carrier
l RAN sharing with dedicated carrier
l Hybrid RAN sharing
According to section 6.2.2 "Message definitions" in 3GPP TS 36.331 V8.5.0, a single cell can
broadcast a maximum of six PLMN IDs. Huawei eNodeBs support RAN sharing among more
than four operators. However, the license control item for RAN Sharing with Common
Carrier, RAN Sharing with Dedicated Carrier, or Hybrid RAN Sharing allows up to four
operators to share RAN resources. If RAN resources need to be shared by more operators, the
corresponding license must be purchased. For details, see 8 RAN Sharing by More
Operators.
Figure 3-1 shows an example of the independent operator mode. In this example, operators A
and B provide network coverage independently. Each operator allows their subscribers to use
the RAN of the other operator during national roaming.
Figure 3-1 RAN sharing between geographically separated networks by allowing national
roaming
l In areas covered by operator A's network, which is the home public land mobile network
(HPLMN) of the UE, operator A serves this UE.
l After the UE moves out of areas covered by operator A's network into those covered by
operator B's network, operator B serves this UE through national roaming.
l In areas where the two networks overlap, the UE can be preferentially handed over back
to operator A's network based on the subscriber profile ID (SPID) policy.
For details about preferential handovers back to HPLMNs based on SPID policies, see
Flexible User Steering.
NOTE
l Multi-operator core network (MOCN): Multiple operators share the RAN, but not the
evolved packet core (EPC), as shown in Figure 3-2.
l Gateway core network (GWCN): Multiple operators share both the RAN and the
mobility management entity (MME), as shown in Figure 3-3. In this architecture, the
MME must support sharing among operators and can deliver the IE Handover
Restriction List to eNodeBs.
Itf-N Connects the OSS and the NMS of an operator. Each operator has
their own Itf-N interface.
Huawei devices support MME separation and sharing in the MOCN and GWCN architectures, which
are defined in section 4.1 "Overview" in 3GPP TS 23.251. Huawei devices also support S-GW
separation and sharing. These functions are inherently supported by 3GPP specifications, although not
being explicitly defined.
Huawei E-UTRAN, including the multi-cell/multicast coordination entity (MCE) and eNodeB, supports
LTE unicast services and evolved multimedia broadcast/multicast services (eMBMSs). The MCE and
eNodeB can be shared among operators as a whole to provide eMBMSs in both the MOCN and GWCN
architectures. Operators can deploy their own eMBMSs in both architectures. This document describes
only LTE unicast services. For details about RAN sharing for eMBMSs, see eMBMS.
4.1 Principles
4.1.1 Overview
In RAN sharing with common carrier, multiple operators share spectrum resources and
eNodeB hardware resources. These operators share a same cell. In a shared cell, multiple
PLMN IDs are broadcast, including the primary operator's PLMN ID and secondary
operators' PLMN IDs. To enable RAN sharing with common carrier, set the
ENodeBSharingMode.ENodeBSharingMode parameter to SHARED_FREQ.
RAN sharing with common carrier is used when:
l One operator owns spectrum resources and shares them with others.
l Multiple operators own spectrum resources and use their resources to form a resource
pool. They share the pooled resources among themselves or with others who do not own
spectrum resources.
Figure 4-1 shows the network architecture for RAN sharing with common carrier.
Figure 4-1 Network architecture for RAN sharing with common carrier
RAN sharing with common carrier differs from the independent operator mode in the
following aspects:
l NE functions
l Idle mode management
l Mobility management in connected mode
l Feature and capacity management
l Fair sharing of air interface resources
l Automatic neighbor relation (ANR) management
l OSS management
l Transmission networking
l Multi-operator PKI
4.1.2 NE Functions
This section describes the NE functions and configurations specific to RAN sharing with
common carrier.
UE
To support RAN sharing with common carrier, UEs must be able to:
In RAN sharing with common carrier, a UE first selects one PLMN (from the PLMNs listed
in SIB1) as the serving PLMN, and reports the PLMN to the eNodeB. The eNodeB then
selects an EPC operator based on the reported information. For details, see 4.1.3.2 EPC
Selection.
eNodeB
To support RAN sharing with common carrier, each eNodeB must support the following
functions:
l Setup of an S1 interface with an MME shared by operators or exclusively used by a
specific operator
l Sharing by a maximum of four operators and broadcast of a maximum of four PLMN
IDs in a shared cell under the control of the RAN Sharing with Common Carrier license
l MME selection for a UE based on the PLMN ID selected by the UE
l Configuration of all PLMNs of a shared intra- and inter-RAT neighboring cell
l Mobility management on a per operator basis
l Reporting of certain counters and alarms on a per operator basis
NOTE
MME
In RAN sharing with common carrier, the MMEs of RAN sharing operators use unique global
eNodeB IDs and E-UTRAN cell global identifiers (ECGIs) to address shared eNodeBs and
cells. An eNodeB uses the global eNodeB ID and ECGI when communicating with MMEs of
the operators over the S1 interfaces. The global eNodeB ID consists of the primary PLMN ID
and eNodeB ID. For details about the global eNodeB IDs and ECGIs, see 4.1.3.1 System
Information Broadcast.
If the GWCN architecture is used, the MME must:
l Allow multiple operators to share eNodeBs and the MME itself.
l Support the delivery of the IE Handover Restriction List. This IE is used to inform the
target eNodeB of UE's serving PLMN during an S1- or X2-based handover. If the MME
does not deliver this IE, the S1- or X2-based handover will fail. For details, see 4.1.4.3
Incoming Handover.
Related Concepts
l PLMN ID
A PLMN ID consists of a mobile network code (MNC) and a mobile country code
(MCC). In RAN sharing with common carrier, multiple PLMN IDs can be broadcast in a
shared cell.
l Primary and secondary operators
The type of an operator is specified by the CnOperator.CnOperatorType parameter.
According to section 6.2.2 "Message definitions" in 3GPP TS 36.331 V8.5.0, the PLMN
at the top of the broadcast PLMN ID list is the primary PLMN. The ID of this PLMN is
contained in the global eNodeB ID and ECGI. The primary and secondary operators can
share eNodeB resources based on predefined proportions. The primary operator does not
have any privileges.
System Information
As defined in section 6.2.2 "Message definitions" in 3GPP TS 36.331 V8.5.0, the contents of
system information block 1 (SIB1) are as follows:
l Cell barring status CellBarred (When a cell belongs to multiple PLMNs, this status is
applied to all of them.)
l Cell reservation status CellReservedForOp (This status is individually applied to each
PLMN.)
Upon S1 setup failures or S1 faults, the cell reservation and barring status are adaptively
changed in SIB1.
l If an S1 link for the primary operator fails to be set up or becomes faulty, the cell is
reserved for this operator.
l If an S1 link for a secondary operator fails to be set up or becomes faulty, the PLMN ID
of this operator is not included in the broadcast PLMN ID list.
l If all S1 links fail to be set up or become faulty, the cell is barred and the eNodeB
broadcasts the barring status in SIB1. If the cell is deactivated before the SIB1 broadcast,
the eNodeB does not broadcast the barring status.
Assume that operator A is the primary operator and operator B is a secondary operator. The
following describes SIB1 in different scenarios:
l Figure 4-2 shows SIB1 when S1 links for operators A and B are normal.
l Figure 4-3 shows SIB1 when the S1 link for operator A is faulty.
l Figure 4-4 shows SIB1 when the S1 link for operator B is faulty.
l When the S1 links for both operators A and B are faulty, the cell is unavailable.
TAC
The CnOperatorTa.Tac parameter specifies the TAC of an EPC operator. The
CellOp.TrackingAreaId parameter specifies the TAI of the cell. Because a cell belongs to
only one tracking area (TA), all operators of a cell must be configured with the same TAC.
That is, the values of all CnOperatorTa.Tac parameters corresponding to the
CellOp.TrackingAreaId parameters must be identical in a cell.
To change the TAC for a cell in which RAN sharing with common carrier is enabled, perform
the following steps:
After the UE selects an EPC, it notifies the eNodeB of the selected EPC through the RRC
Connection Setup Complete message.
The eNodeB then selects the S1 interface based on the PLMN ID selected by the UE and
connects the EPC.
Initial network access is different for UEs that are in their own home PLMNs (HPLMNs) and
those roaming to other PLMNs. In all of these scenarios, one or more PLMN IDs are
broadcast in the shared cell.
If... Then...
The UE selects the EPC of an operator with The eNodeB selects the corresponding EPC,
which a roaming agreement is signed and the EPC allows the UE to attach.
The UE selects the EPC of an operator with The EPC rejects the UE. The UE tries other
which a roaming agreement is not signed EPCs until it attaches to the EPC of an
operator with which a roaming agreement is
signed.
It is recommended that operators consider fairness among different regions or time periods
when they plan the sequence of broadcast PLMN IDs. For example, operators A and B divide
a shared area into eastern and western regions based on user balancing. In the eastern region,
the PLMN ID of operator A is ranked first; in the western region, the PLMN ID of operator B
is ranked first.
To achieve fairness among operators sharing a cell, you can set the
CellAccess.BroadcastMode parameter to specify a PLMN ID broadcast mode in the cell.
Assume that operators A, B, and C share a cell.
l When this parameter is set to NORMAL_MODE, PLMN IDs are broadcast at a fixed
sequence in the cell.
The PLMN IDs in the list are always broadcast in the following sequence:
– Operator A
– Operator B
– Operator C
l When this parameter is set to RR_MODE, the PLMN ID at the top of the PLMN ID list
is rotated in RR mode at a cell-specific interval. This interval is specified by the
CellAccess.RoundPeriod parameter. The start time for broadcast sequence rotation is
specified by the CellAccess.RoundActionTime parameter.
For example, when the CellAccess.RoundPeriod parameter is set to 12, the PLMN IDs
in the list are broadcast in the sequence as shown in Figure 4-5.
l When this parameter is set to FREE_Mode, the PLMN ID at the top of the PLMN ID
list is rotated at an operator-specific interval. This interval is specified by the
CellOp.OperatorPlmnRoundPeriod parameter.
For example, when the CellOp.OperatorPlmnRoundPeriod parameters are set to 12, 11,
and 1 for operators A, B, and C, respectively, the PLMN IDs in the list are broadcast in
the sequence as shown in Figure 4-6.
NOTE
According to section 6.2.2 "Message definitions" in 3GPP TS 36.331 V8.5.0, the primary PLMN is the
one at the top of the broadcast PLMN ID list in SIB1 and also the PLMN in the ECGI. When RAN
sharing with common carrier is enabled and the CellAccess.BroadcastMode parameter is set to
RR_MODE or FREE_Mode, the PLMN at the top of the broadcast PLMN ID list in SIB1 regularly
changes while the primary PLMN in the ECGI does not.
4.1.3.4 Paging
The EPC pages a UE in the following ways:
l The EPC uses the international mobile subscriber identity (IMSI) of the UE for paging.
Each UE has a unique IMSI.
l The EPC uses the SAE-temporary mobile subscriber identity (S-TMSI) of the UE. The
S-TMSI is used to reduce the transmissions of IMSI and improve the efficiency of
paging, service requests, and other radio signaling procedures. An S-TMSI consists of a
mobility management entity code (MMEC) and an MME temporary mobile subscriber
identity (M-TMSI). An MMEC identifies an MME. An M-TMSI is randomly allocated
to a UE within an MME.
To ensure that S-TMSIs are unique in cells where RAN sharing with common carrier is
enabled and prevent paging conflicts, it is recommended that the MMEC of each MME
(including MMEs of the same and different operators) be unique in a TA. The MMECs
of different operators must be negotiated to ensure uniqueness.
If RAN sharing operators can tolerate paging errors caused by MMEC conflicts, you can
set the GlobalProcSwitch.DiffOpWithSameMmecSwitch parameter to ON so that the
eNodeBs allow MMEs of these operators to have the same MMEC.
4.1.3.5 Redirection
A redirection may be performed when the system is overloaded, an S1 interface is faulty, or a
handover fails. During the redirection, the RRC Connection Release message carries operator-
specific frequency or frequency group, which helps the UE promptly re-access the operator's
network.
NOTE
After having camped on a cell, the UE listens to system information. It measures the serving
and neighboring cells according to the neighboring cell measurement and cell reselection
rules to select a more appropriate cell to camp on.
Before cell reselection, the UE is required to measure the signal quality of certain neighboring
cells and evaluate each of them by using the cell reselection criteria based on the cell priority.
During measurement and cell reselection, the UE needs to obtain the priorities of neighboring
frequencies.
There are both intra- and inter-RAT frequency priorities for cell reselection, and there are two
different types of each:
l Common priorities
Common priorities are delivered in cell broadcasts to all the UEs in the cell. They are not
operator-specific. For details, see Idle Mode Management.
l Dedicated priorities
A dedicated priority is generated by an internal algorithm during an RRC connection
release. The dedicated priority is delivered to a specific, single UE in the
IdleModeMobilityControlInfo IE in the RRC Connection Release message.
NOTE
In RAN sharing with common carrier, a shared eNodeB assigns dedicated cell reselection
priorities to UEs of different operators so that operators can use different camping strategies
for UEs in idle mode. The dedicated cell-reselection priority can be configured based on the
following:
l SPID
Operators can configure dedicated cell reselection priorities based on the SPID. The
value range of the SPID is 1–256. Operators are allocated different SPIDs. The
RatFreqPriorityGroup.RatFreqPriorityGroupId parameter specifies the ID of a group
of parameters related to the dedicated cell reselection priorities for each operator. The
SpidCfg.Spid and SpidCfg.RatFreqPriorityGroupId parameters associate operators'
SPIDs with their dedicated cell-reselection priorities. For details, see Flexible User
Steering.
NOTE
To use SPID-specific dedicated cell-reselection priorities in FDD, you must purchase the license
for LOFD-00105401 Camp & Handover Based on SPID.
Dedicated cell-reselection priorities can now be configured based on negotiation-free SPIDs. For
details, see 11 Multi-Operator SPID Policy.
l Serving cell's PLMN
The EutranNFreqSCellOp, UtranNFreqSCellOp, GeranNFGroupSCellOp, and
Cdma2000BcSCellOp MOs specify the dedicated cell-reselection priority of an intra-
RAT neighboring frequency or an inter-RAT neighboring frequency or frequency band
for the PLMN of the serving cell.
Before sending information about the dedicated cell-reselection priority to a UE, the
eNodeB compares the CnOperatorID of the UE's serving PLMN with the
CnOperatorID of a neighboring frequency or frequency band configured for dedicated
cell-reselection priorities based on the serving cell's PLMN. If they are the same, the
eNodeB includes the frequency or frequency band in the information. Otherwise, the
eNodeB does not do so.
NOTE
To use dedicated cell-reselection priorities based on the serving cell's PLMN in FDD, you must
purchase the license for LOFD-001112 MOCN Flexible Priority Based Camping. For details, see
10 MOCN Cell Reselection Priority Configuration.
l Neighboring frequency's HPLMN
Neighboring frequency's HPLMN is the PLMN that is indicated in the system
information broadcast in the cells on the neighboring frequency. Therefore, dedicated
cell reselection priorities based on the neighboring frequency's HPLMN only apply to
PLMNs broadcast for the neighboring frequency. Dedicated cell reselection priorities
based on the neighboring frequency's HPLMN are less flexible than dedicated cell
reselection priorities based on the serving cell's PLMN.
Both the EPLMNs sent from the MME (if the EPlmnSwitch option of the
ENodeBAlgoSwitch.HoAlgoSwitch parameter is selected) and the configured PLMNs that
allow incoming handovers from UE's serving PLMN can be candidates for inter-PLMN
handovers.
The relationships between the three types of dedicated cell reselection priorities are as
follows:
l If the UE is not configured with an SPID, the eNodeB sends the dedicated cell-
reselection priority to the UE based on the serving cell's PLMN or neighboring
frequency's HPLMN. These two types of dedicated cell reselection priorities cannot be
used simultaneously. That is, the MOs related to one type cannot be configured if the
MOs related to the other have been configured. Dedicated cell-reselection based on
serving cell's PLMN is recommended.
NOTE
For details about cell selection and reselection in the independent operator mode, see Idle Mode
Management.
l A list of serving PLMNs of the neighboring UTRAN cell, configured by using the
UtranExternalCellPlmn.ShareMcc and UtranExternalCellPlmn.ShareMnc
parameters
l A list of serving PLMNs of the neighboring GERAN cell, configured by using the
GeranExternalCellPlmn.ShareMcc and GeranExternalCellPlmn.ShareMnc
parameters
When both E-UTRAN and GERAN cells use RAN sharing with common carrier, set the
L2GPLMNChooseOptSwitch option of the GlobalProcSwitch.ProtocolMsgOptSwitch
parameter according to the protocol release the GERAN cell complies with.
– If a GERAN cell complies with 3GPP Release 10 or earlier (a non-standard
scenario), select the L2GPLMNChooseOptSwitch option. For details about RAN
sharing with common carrier in such a cell, see section 4.2.2 "Broadcast system
information for network sharing" in 3GPP TS 23.251 v10.1.0.
In this scenario, only the primary PLMN ID is broadcast in the GERAN cell. The
target PLMN ID carried in messages sent from an E-UTRAN cell to the GERAN
cell, such as handover requests or RIM requests, must be consistent with the
primary PLMN ID configured for the GERAN. If the PLMN IDs are inconsistent,
the requests will fail.
– If a GERAN cell complies with 3GPP Release 11 or later, deselect the
L2GPLMNChooseOptSwitch option. For details about RAN sharing with
common carrier in such a cell, see section 4.2.2 "Broadcast system information for
network sharing" in 3GPP TS 23.251 v11.1.0.
In this scenario, multiple PLMN IDs can be broadcast in the GERAN cell. The
target PLMN ID carried in messages sent from an E-UTRAN cell to the GERAN
cell is the serving PLMN of the UE, which is not necessarily consistent with the
primary PLMN ID configured for the GERAN.
NOTE
CDMA2000 does not support RAN sharing with common carrier. The PLMN information of
CDMA2000 1x neighboring cells and CDMA2000 HPRD neighboring cells is indicated by the MCC
and MNC in the Cdma20001XrttExternalCell and Cdma2000HrpdExternalCell MOs, respectively.
If the target eNodeB does not receive the IE Handover Restriction List, it can identify the
UE's serving PLMN as follows in some cases:
l During an S1- or X2-based handover, if the MME or source eNodeB includes the IE
Handover Restriction List in the handover request message to the target eNodeB, the
target eNodeB selects the serving PLMN indicated in the IE as the serving PLMN of the
UE after the handover.
l During an S1- or X2-based handover, if the MME or source eNodeB does not include the
IE Handover Restriction List in the handover request message to the target eNodeB, the
rules vary depending on the network architecture:
– MOCN: For an S1-based handover, the target eNodeB can select the PLMN
supported by the independent operator's MME that sends the handover request
message as the UE's serving PLMN. For an X2-based handover, the target eNodeB
can select the PLMN identified by the PLMN ID in the IE GUMMEI in the
handover request message as UE's serving PLMN. (GUMMEI is short for globally
unique MME identifier.)
– GWCN: If RAN sharing with common carrier is not enabled in the target cell, the
only PLMN supported by the cell is used as the UE's serving PLMN. If RAN
sharing with common carrier is enabled in the target cell, the MME must support
delivering the IE Handover Restriction List to the eNodeB; otherwise, an S1- or
X2-based handover may fail because the target eNodeB cannot identify the UE's
serving PLMN.
Operators can implement their own frequency delivery policies for handover measurements.
For details, see Mobility Management in Connected Mode.
In RAN sharing with common carrier, a license purchase order is placed by only one party,
who can be the primary operator or a joint venture of multiple operators. Each eNodeB still
has only one license file, which specifies the total licensed limits for all RAN sharing
operators, not for a specific operator.
The number of RRC_CONNECTED UEs served by each operator can be obtained from the
operator-specific performance counters about user quantity.
NOTE
In addition to static sharing, the licensed RRC_CONNECTED UE resources can be dynamically shared
in FDD. An operator (for example, operator A) can share its unused allotment of RRC_CONNECTED
UE resources with another operator (for example, operator B). When operator A's UEs access the
network, they can reclaim those previously shared resources by preemption if needed. The total
proportion of all RRC_CONNECTED UE resources used by operator A is still limited by the amount
specified in the purchased licenses. For details, see 9 Fair User Sharing (FDD).
Traffic
The LicRatio.TrafficSharingType parameter specifies whether the total traffic of the eNodeB
is allocated to operators in proportions.
l If this parameter is set to SHARING, all operators share the total traffic of the eNodeB.
l If this parameter is set to DEDICATE, the traffic of the eNodeB is allocated to operators
in proportions.
For example, if two operators A and B share resources, the eNodeB performs admission
control, congestion control, and scheduling while observing the following two principles:
l When operator B is serving a small number of UEs, the UEs served by operator A can
access the eNodeB and use available eNodeB resources.
l When the number of UEs served by operator B increases, eNodeB scheduling ensures
that the correct proportion of resources is used by operator B. When this happens,
services provided by operator A are affected and the QoS satisfaction rate decreases.
When the eNodeB detects this overload for services provided by operator A, it performs
congestion control.
For FDD, when the CellAlgoSwitch.RanShareModeSwitch parameter is set to
STATIC_SHARING in a cell where RAN sharing with common carrier is enabled, the
eNodeB performs admission control, congestion control, and scheduling on a per operator
basis. RBs are allocated in proportions for each operator in each transmission time interval
(TTI). If an operator has unused RBs in certain TTIs, these RBs cannot be shared by other
operators. For details about admission and congestion control, see Admission and Congestion
Control.
l The CellOp.OpDlRbUsedRatio and CellOp.OpUlRbUsedRatio parameters are
configured for each operator to specify the proportions of the RBs allocated in the
downlink and uplink, respectively. The sum of the CellOp.OpDlRbUsedRatio or
CellOp.OpUlRbUsedRatio parameter values for all operators cannot be greater than
100%. It is recommended that the sum be 100%.
Scheduling priority adjustment enables the proportion of RBs occupied by each operator
to reach or approach the configured RB allocation proportion. To maximize resource
usage, in each TTI,
– When the sum of the CellOp.OpDlRbUsedRatio or CellOp.OpUlRbUsedRatio
parameter values for all operators is less than 100%, the eNodeB does not allocate
any remaining available RBs to operators requiring additional transmission
resources.
– When an operator has unused RBs, other operators cannot use these RBs.
l The eNodeB must calculate and record the following items for each operator to perform
admission control, congestion control, and scheduling on a per operator basis:
– Quality of service (QoS) satisfaction rate corresponding to QoS class identifier
(QCI) x of all UEs (x ranges from 1 to 4)
– RB usage for all guaranteed bit rate (GBR) services. The eNodeB calculates the RB
usage based on the CellOp.OpUlRbUsedRatio and CellOp.OpDlRbUsedRatio
parameter settings.
After this function is enabled, the values of counters in the following counter subsets will
fluctuate:
l Throughput and Data Volume Measurement per CNOperator
(Traffic.Thruput.Cell.Operator)
l PRB Measurement per CNOperator (Traffic.RB.Cell.Operator)
l Throughput and Data Volume Measurement (Traffic.Thruput.Cell)
l PRB Measurement (ChMeas.PRB.Cell)
l eMTC Throughput and Data Volume Measurement (Traffic.Thruput.Cell.eMTC)
RB Sharing Based on Operator Groups
RBs can be shared on a per operator group basis. This function is an enhancement of operator-
specific RB sharing. Some operators may have a partnership with each other. When three or
more operators share a cell, those in a partnership can form a resource group that can be
represented by a member operator, and RBs are preferentially shared within the resource
group. If there are still unused RBs, they can be shared by other operators. This function
ensures that resources are equally allocated to operators in the same resource group.
The eNodeB can perform admission control, congestion control, and scheduling based on
operator resource groups if the OpPrbGroupshareSwitch option of the
CellAlgoSwitch.OpResourceGroupShareSwitch parameter is selected. Operators in the same
resource group must be configured with the same CellOp.OpResourceGroupIndex value.
The proportion of RBs allocated to an operator resource group in the uplink or downlink is the
sum of the CellOp.OpUlRbUsedRatio or CellOp.OpDlRbUsedRatio parameter values for
each operator in the resource group, respectively.
l In the uplink, the RB usage of the cell and the RB usage and QoS satisfaction rate
corresponding to QCI x (x ranges from 1 to 4.) are measured and detected for each
operator to determine whether to admit GBR services. The other processes in RAN
sharing with common carrier are the same as those in the independent operator mode.
l In the downlink, the QoS satisfaction rate corresponding to QCI x (x ranges from 1 to 4.)
is measured and detected for each operator to determine whether to admit GBR services.
The other processes in RAN sharing with common carrier are the same as those in the
independent operator mode.
l GBR service preemption: If GBR services of an operator fail to be admitted, the eNodeB
performs GBR service preemption within the operator.
For details about admission control, see Admission and Congestion Control.
NOTE
When RB sharing based on operator groups is enabled, the preceding functions are performed on a per
operator resource group basis.
l In the uplink, the RB usage of the cell and the RB usage and QoS satisfaction rate
corresponding to QCI x (x ranges from 1 to 4.) are measured and detected for each
operator to determine whether to perform congestion control. The other processes in
RAN sharing with common carrier are the same as those in the independent operator
mode.
l In the downlink, the QoS satisfaction rate corresponding to QCI x (x ranges from 1 to 4.)
is measured and detected for each operator to determine whether to perform congestion
control. The other processes in RAN sharing with common carrier are the same as those
in the independent operator mode.
l Service release: If an operator's cell is overloaded, the eNodeB releases some of the
operator's services. The service release rules are the same as those in the independent
operator mode.
For details about congestion control, see Admission and Congestion Control.
NOTE
When RB sharing based on operator groups is enabled, the preceding functions are performed on a per
operator resource group basis.
NOTE
When RB sharing based on operator groups is enabled, the preceding functions are performed on a per
operator resource group basis.
4.1.6.4 MLB
When RAN sharing is enabled, the eNodeB supports operator-level or operator-group-level
inter-frequency MLB based on the PRB usage or number of UEs.
For details about MLB, see Intra-RAT Mobility Load Balancing.
accordingly. For example, when Cell 1 and Cell 2 may have neighbor relationships, the
parameter needs to be configured as follows:
All of the operators can share the OSS, which manages NEs on the eRAN and connects to
operators' upper-layer NMSs through their own Itf-N interfaces.
The configuration data reported through an operator-specific Itf-N interface from the OSS
includes the eNodeB-level common information and the operator-specific cell-level
information.
On the OSS, some important alarms, such as those related to S1 and X2 interfaces, are sent to
the NMS of each operator through the Itf-N interface. The alarm information sent to the NMS
of an operator includes information exclusive to the operator and common information.
On the OSS side, performance statistics are reported to each individual operator through the
Itf-N interface. Dedicated data is reported to the operator it concerns, and common data is
reported to all operators.
Figure 4-7 MOs for configuring the S1 and X2 interfaces in endpoint mode
Table 4-1 Configuration of dedicated or shared control-plane transmission links for RAN
sharing with common carrier in different topologies
Transmission S1 with Dedicated S1 with Shared X2
Link MMEs MMEs
Table 4-2 Configuration of dedicated or shared user-plane transmission links for RAN sharing
with common carrier in different topologies
Transmission S1 with Dedicated S1 with Shared S- X2
Link S-GWs GWs
Endpoint Mode
Table 4-3 Control-plane transmission link configuration in endpoint mode for RAN sharing
with common carrier
Configuration S1 with Dedicated S1 with Shared X2
Item MMEs MMEs
Table 4-4 User-plane transmission link configuration in endpoint mode for RAN sharing with
common carrier
Configuration S1 with Dedicated S1 with Shared S- X2
Item S-GWs GWs
When all operators use the same local and peer user-plane IP address:
l If an eNodeB works in RAN sharing with common carrier mode, configure the same
EPGroup MO for all operators. Otherwise, only the first user-plane channel can be
successfully set up.
l If the newly configured EPGroup MO for which the user-plane link is to be set up has
the same local and peer user-plane IP addresses as an existing EPGroup MO, delete the
newly configured MO or refer it to the existing EPGroup MO. Otherwise, user-plane
link setup will fail.
When an eNodeB autonomously obtains the peer X2 control-plane IP addresses (that is, when
the SCTPPEER MO is not configured):
Only handovers for UEs of a specific operator configured with an X2 MO can trigger the
setup of an X2 control-plane link. The UEs served by the other operators can be handed over
through the X2 interface only after the control-plane link is set up.
Link Mode
Table 4-5 Control-plane transmission link configuration in link mode for RAN sharing with
common carrier
Transmission S1 with Dedicated S1 with Shared X2
Link MMEs MMEs
Table 4-6 User-plane transmission link configuration in link mode for RAN sharing with
common carrier
Transmission S1 with Dedicated S1 with Shared S- X2
Link S-GWs GWs
4.2.1 Benefits
RAN sharing provides the following benefits for operators:
4.2.2 Impacts
Network Impacts
If the UE distribution is different among RAN sharing operators, the throughput may change
after RAN sharing with common carrier is enabled. The throughput is not affected if the UE
distribution is consistent among RAN sharing operators.
If the RB proportions vary greatly between the RAN sharing operators (for example, 9:1 for
two operators), UEs served by the operator with a smaller RB proportion experience a longer
scheduling delay after RAN sharing with common carrier is enabled. However, the scheduling
delay can still meet the QoS requirements specified in section 6.1.7.2 "Standardized QCI
characteristics" in 3GPP TS 23.203 V8.5.0.
This function has no impact on NB-IoT.
Function Impacts
RAT Function Function Switch Reference Description
Name
4.3 Requirements
4.3.1 Licenses
RAT Feature ID Feature Name Model Sales Unit
4.3.2 Software
Prerequisite Functions
RAT Function Function Switch Reference Description
Name
4.3.3 Hardware
For NB-IoT, the following base stations are compatible with this function:
Boards
No requirements
RF Modules
No requirements
4.3.4 Others
None
Scenario-specific data for RAN sharing with common carrier can be configured based on
information provided in Cell Management, Mobility Management in Connected Mode, and
this section.
Table 4-7 Parameters used for activation in both FDD and NB-IoT
Parameter Parameter ID Setting Notes
Name
Tracking area CnOperatorTa In a cell where RAN sharing with common carrier is
code .Tac enabled, configure the same TAC for all operators.
Local tracking CellOp.Tracki In a cell where RAN sharing with common carrier is
area ID ngAreaId enabled, the CnOperatorTa.CnOperatorId
parameter values must be different. One of the
parameter values must correspond to the primary
operator.
The following table describes the parameters used for function activation specific to FDD.
The following table describes the parameters used for function activation specific to NB-IoT.
The following table describes the parameters used for function optimization in both FDD and
NB-IoT.
Table 4-10 Parameters used for optimization in both FDD and NB-IoT
Plmn Broadcast CellAccess.Bro Set this parameter based on the network plan.
Mode adcastMode
The following table describes the parameters used for function optimization specific to FDD.
The following table describes the FDD parameters that must be set to configure the dedicated
cell-reselection priority for a GERAN frequency based on the serving cell's PLMN.
Cell reselection GeranNFGrou Set this parameter based on the network plan.
dedicated pSCellOp.Cell
priority ReselDediPri
The following table describes the FDD parameters that must be set to configure the dedicated
cell-reselection priority for a GERAN frequency based on the neighboring frequency's
HPLMN.
Cell reselection GeranRanSha Set this parameter based on the network plan.
priority re.CellReselPri
ority
The following table describes the FDD parameters that must be set to configure the dedicated
cell-reselection priority for a UTRAN frequency based on the serving cell's PLMN.
Cell reselection UtranNFreqS Set this parameter based on the network plan.
dedicated CellOp.CellRes
priority elDediPri
The following table describes the FDD parameters that must be set to configure the dedicated
cell-reselection priority for a UTRAN frequency based on the neighboring frequency's
HPLMN.
Cell reselection UtranRanShar Set this parameter based on the network plan.
priority e.CellReselPrio
rity
The following table describes the FDD parameters that must be set to configure the dedicated
cell-reselection priority for an E-UTRAN frequency based on the serving cell's PLMN.
Cell reselection EutranNFreqS Set this parameter based on the network plan.
dedicated CellOp.CellRes
priority elDediPri
The following table describes the FDD parameters that must be set to configure the dedicated
cell-reselection priority for an E-UTRAN frequency based on the neighboring frequency's
HPLMN.
Cell reselection EutranNFreq Set this parameter based on the network plan.
priority RanShare.Cell
ReselPriority
The following table describes the FDD parameters that must be set to configure the dedicated
cell-reselection priority for a CDMA frequency.
The following table describes the FDD parameter that must be set when both the E-UTRAN
and GERAN cells use RAN sharing with common carrier.
The following table describes the parameters used for function optimization specific to NB-
IoT.
l Changing the sharing mode of an eNodeB from the RAN sharing with common carrier
mode to the independent operator mode
The following MOs need to be reconfigured:
a. (Optional) EutranIntraFreqNCell: Used to remove the neighboring relationships
with intra-frequency E-UTRAN cells in FDD. EutranInterFreqNCell: Used to
remove the neighboring relationships with inter-frequency E-UTRAN cells in FDD.
b. (Optional) EutranExternalCell and EutranExternalCellPlmn: Used to remove
the external E-UTRAN cells and PLMN lists for the local cell and cells that have
neighbor relationships with the local cell in FDD.
c. (Optional) X2Interface: Used to remove the X2 interface in FDD.
d. (Optional) LicRatio: Used to change the traffic sharing mode in FDD.
e. (Optional) LicRatioSharePolicy: Used to remove the configuration of the licensed
traffic proportion for each operator and the percentage of available resources one
operator can share with other operators in FDD.
f. (Optional) NbSharingPolicy: Used to remove the configured proportion of UE
contexts that can be stored in NB-IoT user-plane mode on a per operator basis.
g. CellOp: Used to remove the cell operator information.
h. S1Interface: Used to remove the S1 interface.
i. CnOperatorTa: Used to remove the tracking area information.
j. (Optional) LicenseSharingPolicy: Used to remove the configured licensed
proportion of RRC_CONNECTED UEs for each operator in FDD.
k. CellAlgoSwitch: Used to turn off the cell-specific RAN sharing switch.
l. (Optional) EutranNFreqSCellOp, UtranNFreqSCellOp,
GeranNFGroupSCellOp, or Cdma2000BcSCellOp: Used to remove the
dedicated cell-reselection priority configured based on the serving cell's PLMN in
FDD.
m. (Optional) UtranRanShare, GeranRanShare, or EutranNFreqRanShare: Used
to remove the dedicated cell-reselection priority configured based on the
neighboring frequency's HPLMN in FDD.
n. CnOperator: Used to remove the operator information.
o. ENodeBSharingMode: Used to set the eNodeB sharing mode to the independent
operator mode. After the modification, you need to run the RST APP command to
reset the application referenced by the eNodeB function for the application to take
effect (the application ID can be queried by running the LST
ENODEBFUNCTION command).
p. (Optional) ENodeBAlgoSwitch.RanSharingAnrSwitch: Used to turn off the ANR
switch in the adjacent cells that have neighbor relationships with the local cell in
FDD.
Configuring a dedicated cell-reselection priority for a CDMA frequency (based on the serving
cell's PLMN)
ADD CDMA2000BCSCELLOP: LocalCellId=0, BandClass=bc0, CnOperatorID=0,
Cdma1XrttCellReselPriInd=NOT_CFG, HrpdCellReselDediPriCfgInd=NOT_CFG;
ADD CDMA2000BCSCELLOP: LocalCellId=0, BandClass=bc0, CnOperatorID=1,
Cdma1XrttCellReselPriInd=NOT_CFG, HrpdCellReselDediPriCfgInd=NOT_CFG;
Configuring the protocol message optimization switch when RAN sharing with common
carrier is enabled in both the E-UTRAN and GERAN cells
MOD GLOBALPROCSWITCH: ProtocolMsgOptSwitch=L2GPLMNChooseOptSwitch-1;
Procedure
Step 1 Check the cell status by running the following command:
DSP CELL:LOCALCELLID=0;
Expected result:
The cell status is normal.
The following is an example of the command output for normal cell status:
--------------------------start--------------------------
%%/*34421*/DSP CELL:;%%
RETCODE = 0 Operation succeeded.
...
Local cell ID = 0
Cell instance state = Normal
...
--------------------------end---------------------------
Step 2 View the information contained in the SIB1 broadcast in the cell.
Expected result:
Step 3 If "mcc" and "mnc" of the "plmn-Identity" fields in SIB1 are consistent with the operators'
PLMNs, PLMN information about the primary and secondary operators has been correctly
sent in SIB1. This indicates that the function has been activated successfully. In this example,
the first PLMN indicates the primary operator whose "plmn-Identity" field is "46001." The
second PLMN indicates the secondary operator whose "plmn-Identity" field is "46003."
systemInformationBlockType1
cellAccessRelatedInfo
plmn-IdentityList
PLMN-IdentityInfo
plmn-Identity
mcc
MCC-MNC-Digit:0x4 (4)
MCC-MNC-Digit:0x6 (6)
MCC-MNC-Digit:0x0 (0)
mnc
MCC-MNC-Digit:0x6 (0)
MCC-MNC-Digit:0x1 (1)
cellReservedForOperatorUse:notReserved (1)
PLMN-IdentityInfo
plmn-Identity
mcc
MCC-MNC-Digit:0x4 (4)
MCC-MNC-Digit:0x6 (6)
MCC-MNC-Digit:0x0 (0)
mnc
MCC-MNC-Digit:0x0 (0)
MCC-MNC-Digit:0x3 (3)
cellReservedForOperatorUse:notReserved (1)
trackingAreaCode:0000000000100001(00 21)
cellIdentity:0000001100110001101000000000(03 31 A0 00)
Step 4 Power on the two UEs to initiate attach procedures towards the shared cell.
Expected result:
In the "tAI" information element (IE) in the S1AP_INITIAL_UE_MSG message traced over
each S1 interface, the values of "PLMNidentity" and "TAC" are consistent with the operator
data. This indicates that the UEs have successfully accessed the shared cell and selected the
correct EPCs. The path of the "tAI" IE is S1ap-Msg\initiatingMessage\value
\initialUEMessage\protocolIEs\SEQUENCE\value\tAI.
The values of "PLMNidentity" and "TAC" in the traced message are mapped to the eNodeB
configurations as follows. The PLMN ID 46001 is used as an example.
l The MCC is 460 and MNC is F01 (F is added if there are fewer than three digits), which
are combined as 460F01. Then, each two adjacent digits exchange positions to get
64F010, which is the value of "PLMNidentity" in the traced message.
l The value of "TAC" is a hexadecimal number in the traced message.
----End
Table 4-13 lists the operator-specific FDD counters. For details, see Performance Counter
Reference of eNodeBs.
Paging l L.Paging.S1.Rx.PLMN
Measurement per
CNOperator
(Paging.Cell.Operat
or)
Table 4-14 lists the operator-specific NB-IoT counters. For details, see Performance Counter
Reference of eNodeBs.
5.1 Principles
5.1.1 Overview
In RAN sharing with dedicated carrier, operators share eNodeBs but not cells. Only one
PLMN ID is broadcast in each cell. To enable RAN sharing with dedicated carrier, set the
ENodeBSharingMode.ENodeBSharingMode parameter to SEPARATED_FREQ.
RAN sharing with dedicated carrier is used when:
l Each operator has their own spectrum resources but they jointly construct eNodeBs and
share eNodeB hardware.
l One operator owns spectrum resources and provides certain frequencies to be used
exclusively by another operator.
Figure 5-1 illustrates the network architecture for RAN sharing with dedicated carrier where
operators A and B have their own spectrum and share only eNodeB hardware resources.
Figure 5-1 Network architecture for RAN sharing with dedicated carrier
Unlike RAN sharing with common carrier, RAN sharing with dedicated carrier allows
operators to have their exclusive cells. Therefore, the functions (idle mode management,
mobility management in connected mode, and air interface resource sharing between cells)
dedicated to RAN sharing with common carrier are not required in RAN sharing with
dedicated carrier. RAN sharing with dedicated carrier also differs from RAN sharing with
common carrier in the following ways:
l NE functions
l Feature and capacity management
l OSS management
l Transmission networking
l Multi-operator PKI
5.1.2 NE Functions
l RAN sharing with dedicated carrier does not have special requirements for UEs because
operators have their exclusive cells and RAN sharing with dedicated carrier is
transparent to UEs.
l In MOCN mode, RAN sharing with dedicated carrier does not have special requirements
for EPCs.
l In GWCN mode, RAN sharing with dedicated carrier requires that the MME supports
multiple PLMNs and supports the sending of the IE Handover Restriction List to avoid
X2- or S1-based handover failures.
eNodeB-level features are shared between operators and cannot be sold on a per operator
basis.
Capacity management for RAN sharing with dedicated carrier is the same as that for RAN
sharing with common carrier. For details, see 4.1.5 Feature and Capacity Management.
In RAN sharing with dedicated carrier, operators need to have their own transmission links
(S1 and X2 interfaces), as listed in Table 5-1 and Table 5-2.
Table 5-1 Dedicated or shared transmission link configuration in the control plane for RAN
sharing with dedicated carrier mode in different topologies
Transmission S1 with Dedicated S1 with Shared X2
Link MMEs MMEs
Table 5-2 Dedicated or shared transmission link configuration in the user plane for RAN
sharing with dedicated carrier mode in different topologies
Transmission S1 with Dedicated S1 with Shared S- X2
Link S-GWs GWs
Endpoint Mode
Table 5-3 Control-plane transmission link configuration in endpoint mode for RAN sharing
with dedicated carrier
Configuration S1 with Dedicated S1 with Shared X2
Item MMEs MMEs
Table 5-4 User-plane transmission link configuration in endpoint mode for RAN sharing with
dedicated carrier
Configuration S1 with Dedicated S1 with Shared S- X2
Item S-GWs GWs
Link Mode
Table 5-5 Control-plane transmission link configuration in link mode for RAN sharing with
dedicated carrier
Transmission S1 with Dedicated S1 with Shared X2
Link MMEs MMEs
Table 5-6 User-plane transmission link configuration in link mode for RAN sharing with
dedicated carrier
Transmission S1 with Dedicated S1 with Shared S- X2
Link S-GWs GWs
5.2.1 Benefits
The benefits are the same as those provided by RAN sharing with common carrier. For
details, see 4.2.1 Benefits.
5.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Switch Reference Description
Name
5.3 Requirements
5.3.1 Licenses
RAT Feature ID Feature Name Model Sales Unit
5.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
5.3.3 Hardware
Base Station Models
For FDD, the following base stations are compatible with this function:
l 3900 and 5900 series base stations
l DBS3900 LampSite and DBS5900 LampSite
For NB-IoT, the following base stations are compatible with this function:
l 3900 and 5900 series base stations
l DBS3900 LampSite and DBS5900 LampSite
Boards
No requirements
RF Modules
No requirements
5.3.4 Others
None
architecture in use. For details, see 5.1.6 Transmission Networking and S1 and X2 Self-
Management.
Scenario-specific data for RAN sharing with dedicated carrier can be configured based on
information provided in Cell Management and this section.
The following table describes the parameters used for function activation specific to NB-IoT.
The following table describes the parameters used for function optimization in both FDD and
NB-IoT.
Table 5-9 Parameters used for optimization in both FDD and NB-IoT
Parameter Name Parameter ID Setting Notes
The following table describes the parameters used for function optimization specific to FDD.
The following table describes the parameters used for function optimization specific to NB-
IoT.
l The sharing mode of an eNodeB is changed from the independent operator mode to the
RAN sharing with dedicated carrier mode. For example, if two operators are going to
share eNodeB hardware resources, the eNodeB sharing mode must be changed, a cell
must be added, and the related secondary-operator parameters must be set.
l A secondary operator is added. For example, if a third operator is added to share eNodeB
hardware resources, a cell must be added and the related secondary-operator parameters
must be set for this operator.
l A secondary operator is removed. For example, if a secondary operator is removed from
the three operators that share eNodeB hardware resources, a cell and the related
secondary-operator configurations must be removed.
l The sharing mode of an eNodeB is changed from the RAN sharing with dedicated carrier
mode to the independent operator mode.
Transmission on the S1 interface for any given operator can be configured in endpoint or link
mode. For the configurations in endpoint mode, see S1 and X2 Self-Management. For the
configurations in link mode, see Transmission Resource Management.
The following provides the eNodeB- and operator-related MOs to be reconfigured. For details
about the parameters in the MOs and the parameter settings, see Parameters for Initial
Configuration.
l Changing the sharing mode of an eNodeB from the independent operator mode to the
RAN sharing with dedicated carrier mode
The following MOs need to be reconfigured:
a. ENodeBSharingMode: Used to set the eNodeB sharing mode. After the
modification, you need to run the RST APP command to reset the application
referenced by the eNodeB function for the application to take effect (the application
ID can be queried by running the LST ENODEBFUNCTION command).
b. CnOperator: Used to add operator information.
c. (Optional) LicenseSharingPolicy: Used to set the licensed proportion of
RRC_CONNECTED UEs for each operator in FDD.
d. (Optional) NbSharingPolicy: Used to set the proportion of UE contexts that can be
stored in NB-IoT user-plane mode on a per operator basis.
e. CnOperatorTa: Used to add tracking area information.
f. CellOp: Used to set the cell operator information.
g. (Optional) LicRatio: Used to set the traffic sharing mode in FDD.
h. (Optional) LicRatioSharePolicy: Used to set the licensed traffic proportion for
each operator and the percentage of available resources one operator can share with
other operators in FDD.
l Adding a secondary operator
The following MOs need to be reconfigured:
a. CnOperator: Used to add operator information.
b. (Optional) LicenseSharingPolicy: Used to set the licensed proportion of
RRC_CONNECTED UEs for each operator in FDD.
c. (Optional) NbSharingPolicy: Used to set the proportion of UE contexts that can be
stored in NB-IoT user-plane mode on a per operator basis.
d. CnOperatorTa: Used to add tracking area information.
e. CellOp: Used to set the cell operator information.
f. (Optional) LicRatio: Used to set the traffic sharing mode in FDD.
g. (Optional) LicRatioSharePolicy: Used to set the licensed traffic proportion for
each operator and the percentage of available resources one operator can share with
other operators in FDD.
l Removing a secondary operator
The following MOs need to be reconfigured:
a. (Optional) LicenseSharingPolicy: Used to remove the configured licensed
proportion of RRC_CONNECTED UEs for each operator in FDD.
b. (Optional) LicRatio: Used to change the traffic sharing mode in FDD.
c. (Optional) NbSharingPolicy: Used to remove the configured proportion of UE
contexts that can be stored in NB-IoT user-plane mode on a per operator basis.
d. CellOp: Used to remove the cell operator information.
e. CnOperatorTa: Used to remove the tracking area information.
Procedure
Step 1 Check the cell status by running the following commands:
DSP CELL:LOCALCELLID=0;
DSP CELL:LOCALCELLID=1;
Expected result:
The cell status is normal.
The following is an example of the command output for normal cell status:
--------------------------start--------------------------
%%/*44421*/DSP CELL: LOCALCELLID=0;%%
RETCODE = 0 Operation succeeded.
...
Local cell ID = 0
Cell instance state = Normal
...
%%/*44423*/DSP CELL: LOCALCELLID=1;%%
RETCODE = 0 Operation succeeded.
...
Local cell ID = 1
Cell instance state = Normal
...
--------------------------end---------------------------
Step 3 Power on the two UEs to initiate attach procedures towards the respective cells.
Expected result:
In the "tAI" IE in the S1AP_INITIAL_UE_MSG message traced on each S1 interface, the
values of "PLMNidentity" and "TAC" are consistent with the operator data. This indicates that
the UEs have successfully accessed the respective cells and selected the correct EPCs. In this
situation, the function has been activated successfully. The path of the "tAI" IE is S1ap-Msg
\initiatingMessage\value\initialUEMessage\protocolIEs\SEQUENCE\value\tAI.
----End
6.1 Principles
6.1.1 Overview
In RAN sharing with special dedicated carrier, operators share eNodeB hardware resources,
but not spectrum resources. Only one PLMN ID is broadcast in cells of the primary operator.
In cells of a secondary operator, the PLMN IDs of both the primary operator in a reserved
state and the secondary operator are broadcast. To enable RAN sharing with special dedicated
carrier, set the ENodeBSharingMode.ENodeBSharingMode parameter to
SEPARATED_FREQ_SPEC. RAN sharing with special dedicated carrier is used during
swapping of another vendor's devices on a network with dedicated carriers.
A secondary operator can choose to allow or not allow spectrum resources in their cells to be
used by UEs subscribing to services of the primary operator. For ease of description, the two
cases are defined as case 1 and case 2 in subsequent descriptions as follows:
l Case 1: The CellOp MO of the primary operator is not configured for cells of a
secondary operator. In this case, UEs subscribing to services of the primary operator are
not allowed to use the spectrum resources of the secondary operator.
l Case 2: The CellOp MO of the primary operator must be configured for cells of a
secondary operator. The CellOp.CellReservedForOp parameter is set to
CELL_RESERVED_FOR_OP and the CnOperatorTa MO associated with the
CellOp.TrackingAreaID parameter must be configured. In this case, UEs subscribing to
services of the primary operator are allowed to use the spectrum resources of the
secondary operator.
NOTE
In RAN sharing with special dedicated carrier, the GWCN architecture only supports case 2. When the
MOCN and GWCN coexist, only case 2 is supported.
RAN sharing with special dedicated carrier works only in FDD cells where NB-IoT is not
used. When RAN sharing with special dedicated carrier is enabled, NB-IoT cells cannot
provide services.
RAN sharing with special dedicated carrier is different from RAN sharing with common
carrier or RAN sharing with dedicated carrier in the following ways. The subsequent sections
describe only the differences.
6.1.2 NE Functions
The NE functions required by RAN sharing with special dedicated carrier are the same as
those required by RAN sharing with common carrier. For details, see 4.1.2 NE Functions.
Two PLMN IDs are broadcast in cells of a secondary operator. For details, see 6.1.1
Overview.
6.1.3.4 Paging
Paging for special dedicated carrier is the same as that for RAN sharing with common carrier.
For details, see 4.1.3.4 Paging.
6.1.3.5 Redirection
Redirection for special dedicated carrier is the same as that for RAN sharing with common
carrier. For details, see 4.1.3.5 Redirection.
l No CellOp MO is configured.
l The broadcast PLMN ID is in the "reserved" state.
Other aspects of cell selection and reselection for RAN sharing with special dedicated carrier
are the same as those for RAN sharing with common carrier. For details, see 4.1.3.6 Cell
Selection and Reselection.
In case 1, UEs subscribing to services of the primary operator are prohibited from using the
spectrum resources of a secondary operator. Therefore, inter-PLMN intra-eNodeB handovers
to cells of the secondary operator are not possible for such UEs. When cells of a secondary
operator and those of the primary operator are not served by the same eNodeB, there will be
no handovers between them. This is because the frequencies of the former are not configured
as neighboring frequencies for the latter to establish any neighbor relationships.
Other aspects of mobility management in connected mode for RAN sharing with special
dedicated carrier are the same as those for RAN sharing with common carrier. For details, see
4.1.4 Mobility Management in Connected Mode. Note that if a cell where RAN sharing
with special dedicated carrier is enabled needs to be manually configured as a neighboring
cell, the PLMN used to configure external cells and add inter-frequency neighbor
relationships must be the one queried by running LST CNOPERATOR with the
CnOperator.CnOperatorType parameter is set to CNOPERATOR_PRIMARY.
eNodeB-level features are shared between operators and cannot be sold on a per operator
basis.
Capacity management for RAN sharing with special dedicated carrier is the same as that for
RAN sharing with common carrier. For details, see 4.1.5 Feature and Capacity
Management.
6.2.1 Benefits
RAN sharing with special dedicated carrier increases the handover success rate during inter-
vendor device swapping. This is because there will be no handover failures between adjacent
inter-vendor eNodeBs caused by incorrect neighbor relationships.
Other benefits are the same as those provided by RAN sharing with common carrier. For
details, see 4.2.1 Benefits.
6.2.2 Impacts
Network Impacts
RAN sharing with special dedicated carrier increases the handover success rate during inter-
vendor device swapping. This is because there will be no handover failures between adjacent
inter-vendor eNodeBs caused by incorrect neighbor relationships.
Function Impacts
None
6.3 Requirements
6.3.1 Licenses
RAT Feature ID Feature Name Model Sales Unit
6.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
Function Function Switch Reference Description
Name
6.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
6.3.4 Others
None
l The sharing mode of an eNodeB is changed from the independent operator mode to the
RAN sharing with special dedicated carrier mode. For example, if two operators are
going to share RAN resources in RAN sharing with special dedicated carrier mode, the
eNodeB sharing mode must be changed, a cell must be added, and the related secondary-
operator parameters must be set.
l A secondary operator is added. For example, if a third operator is added to share RAN
resources in RAN sharing with special dedicated carrier mode, a cell must be added and
the related secondary-operator parameters must be set for this operator.
l A secondary operator is removed. For example, if a secondary operator is removed from
the three operators that share RAN resources in RAN sharing with special dedicated
carrier mode, a cell and the related secondary-operator configurations must be removed.
l The sharing mode of an eNodeB is changed from the RAN sharing with special
dedicated carrier mode to the independent operator mode.
Transmission on the S1 interface for any given operator can be configured in endpoint or link
mode. For the configurations in endpoint mode, see S1 and X2 Self-Management. For the
configurations in link mode, see Transmission Resource Management.
The following provides the eNodeB- and operator-related MOs to be reconfigured. For details
about the parameters in the MOs and the parameter settings, see Parameters for Initial
Configuration.
l Changing the sharing mode of an eNodeB from the independent operator mode to the
RAN sharing with special dedicated carrier mode
The following MOs need to be reconfigured:
a. ENodeBSharingMode: Used to set the eNodeB sharing mode. After the
modification, you need to run the RST APP command to reset the application
referenced by the eNodeB function for the application to take effect (the application
ID can be queried by running the LST ENODEBFUNCTION command).
b. CnOperator: Used to add operator information.
c. (Optional) LicenseSharingPolicy: Used to set the licensed proportion of
RRC_CONNECTED UEs for each operator in FDD.
d. (Optional) NbSharingPolicy: Used to set the proportion of UE contexts that can be
stored in NB-IoT user-plane mode on a per operator basis.
e. CnOperatorTa: Used to add tracking area information.
f. CellOp: Used to set the cell operator information.
g. (Optional) LicRatio: Used to set the traffic sharing mode in FDD.
h. (Optional) LicRatioSharePolicy: Used to set the licensed traffic proportion for
each operator and the percentage of available resources one operator can share with
other operators in FDD.
l Adding a secondary operator
The following MOs need to be reconfigured:
a. CnOperator: Used to add operator information.
b. (Optional) LicenseSharingPolicy: Used to set the licensed proportion of
RRC_CONNECTED UEs for each operator in FDD.
c. (Optional) NbSharingPolicy: Used to set the proportion of UE contexts that can be
stored in NB-IoT user-plane mode on a per operator basis.
d. CnOperatorTa: Used to add tracking area information.
e. CellOp: Used to set the cell operator information.
f. (Optional) LicRatio: Used to set the traffic sharing mode in FDD.
g. (Optional) LicRatioSharePolicy: Used to set the licensed traffic proportion for
each operator and the percentage of available resources one operator can share with
other operators in FDD.
l Removing a secondary operator
The following MOs need to be reconfigured:
a. (Optional) LicenseSharingPolicy: Used to remove the configured licensed
proportion of RRC_CONNECTED UEs for each operator in FDD.
b. (Optional) LicRatio: Used to change the traffic sharing mode in FDD.
c. (Optional) NbSharingPolicy: Used to remove the configured proportion of UE
contexts that can be stored in NB-IoT user-plane mode on a per operator basis.
d. CellOp: Used to remove the cell operator information.
e. CnOperatorTa: Used to remove the tracking area information.
used.
ADD S1INTERFACE: S1InterfaceId=0, S1CpBearerId=0, CnOperatorId=0;
ADD X2INTERFACE: X2InterfaceId=0, X2CpBearerId=0, CnOperatorId=0;
//Configuring a TAC for the primary operator in a reserved state when case 2 of
RAN sharing with special dedicated carrier is used
ADD CNOPERATORTA: TrackingAreaId=1, CnOperatorId=0, Tac=1;
//Performing this step for the cell of the primary operator
ADD CELLOP: LocalCellId=0, TrackingAreaId=0,
CellReservedForOp=CELL_NOT_RESERVED_FOR_OP;
//Resetting the application referenced by the eNodeB function for the application
to take effect (the application ID can be queried by running the LST
ENODEBFUNCTION command)
RST APP: AID=1;
Prerequisites
1. Based on the network plan, the eNodeB is shared between two operators that use case 1
of RAN sharing with special dedicated carrier.
2. The transmission links between the eNodeB and EPCs are functioning normally.
3. Two UEs (UE 1 and UE 2) are ready. They respectively subscribe to services of the two
operators.
Procedure
Step 1 Check the cell status by running the following commands:
DSP CELL:LOCALCELLID=0;
DSP CELL:LOCALCELLID=1;
Expected result:
The cell status is normal.
The following is an example of the command output for normal cell status:
--------------------------start--------------------------
%%/*44421*/DSP CELL: LOCALCELLID=0;%%
RETCODE = 0
Operation succeeded.
...
Local cell ID = 0
Cell instance state = Normal
...
%%/44423*/DSP CELL: LOCALCELLID=1;%%
RETCODE = 0
Operation succeeded.
...
Local cell ID = 1
Cell instance state = Normal
...
--------------------------end---------------------------
cellReservedForOperatorUse:notReserved (1)
trackingAreaCode:0000000000100001(00 21)
cellIdentity:0000001100110001101000000000(03 31 A0 00)
In SIB1 of Cell 1, the "plmn-Identity" field is "46001" and the status is "Reserved" for the
primary operator and the "plmn-Identity" field is "46003" for the secondary operator.
systemInformationBlockType1
cellAccessRelatedInfo
plmn-IdentityList
PLMN-IdentityInfo
plmn-Identity
mcc
MCC-MNC-Digit:0x4 (4)
MCC-MNC-Digit:0x6 (6)
MCC-MNC-Digit:0x0 (0)
mnc
MCC-MNC-Digit:0x0 (0)
MCC-MNC-Digit:0x1 (1)
cellReservedForOperatorUse:Reserved (0)
PLMN-IdentityInfo
plmn-Identity
mcc
MCC-MNC-Digit:0x4 (4)
MCC-MNC-Digit:0x6 (6)
MCC-MNC-Digit:0x0 (0)
mnc
MCC-MNC-Digit:0x0 (0)
MCC-MNC-Digit:0x3 (3)
cellReservedForOperatorUse:notReserved (1)
trackingAreaCode:0000000000000001(00 01)
cellIdentity:0000001100110001101000000001(03 31 A0 01)
Step 3 Power on the two UEs to initiate attach procedures towards the respective cells.
Expected result:
----End
For cells of a secondary operator in case 2, some cell-level performance counters can be
monitored on a per operator basis. These counters are used to indicate whether the network
KPIs meet operators' requirements and whether proportion-based resource sharing achieves
the expected effect. Operators can use these counters for preliminary fault demarcation and
locating. RAN sharing with special dedicated carrier and RAN sharing with common carrier
use the same operator-specific counters. For details about these counters, see 4.4.3 Network
Monitoring.
7.1 Principles
7.1.1 Overview
In hybrid RAN sharing, operators share eNodeB hardware resources. They can choose to
share spectrum resources or keep spectrum resources for their own use. In a shared cell,
multiple PLMN IDs are broadcast, including the primary operator's and secondary operators'
PLMN IDs. The primary operator's PLMN ID can be different between cells. To enable
hybrid RAN sharing, set the ENodeBSharingMode.ENodeBSharingMode parameter to
HYBRID_SHARED.
Hybrid RAN sharing is typically used in the following scenarios:
l Scenario 1: One operator shares some of its spectrum resources with other operators.
Other spectrum resources are still exclusively used by this operator. The primary PLMNs
of the shared and the non-shared spectrum resources are different.
Figure 7-1 shows the network architecture for hybrid RAN sharing where operators A
and B have their own spectrum resources and share eNodeB hardware resources and
some of the spectrum resources. Frequency 1 (f1) is shared by operators A and B, with A
being the primary operator and B being the secondary one. Frequency 2 (f2) is
exclusively used by operator B.
In this scenario, there are two RAN sharing groups: operators (A and B) and operator B.
Each RAN sharing group must have a unique primary operator. The secondary operators
can be the same.
l Scenario 2: Operators co-construct and share a RAN. Different operators share different
spectrum resources.
Figure 7-2 shows the network architecture for hybrid RAN sharing where operators A,
B, C, and D share eNodeB hardware resources and different spectrums. f1 is shared by
operators A and B, while f2 is shared by operators C and D. Operators (A and B) and
operators (C and D) are members of different RAN sharing groups.
To conclude, all the following conditions must be met before hybrid RAN sharing is enabled:
l Compared with RAN sharing with common carrier, hybrid RAN sharing allows the
primary PLMN ID to be different between cells.
l Compared with RAN sharing with dedicated carrier, hybrid RAN sharing allows
operators to share the same cell.
Hybrid RAN sharing is different from RAN sharing with common carrier or RAN sharing
with dedicated carrier in the following ways. The subsequent sections describe only the
differences.
l NE functions
l Idle mode management
l Feature and capacity management
l Fair sharing of air interface resources
l ANR management
l OSS management
l Transmission networking
7.1.2 NE Functions
Some NEs in hybrid RAN sharing have specific functions and configurations, besides all
functions in RAN sharing with common carrier and RAN sharing with dedicated carrier. This
section describes the NE functions and configurations specific to hybrid RAN sharing.
UE
Functions of a UE are the same as those in RAN sharing with common carrier. For details, see
4.1.2 NE Functions.
eNodeB
To support hybrid RAN sharing, an eNodeB must support all functions in RAN sharing with
common carrier and RAN sharing with dedicated carrier, and also must be able to:
MME
Functions of an MME are the same as those in RAN sharing with common carrier. For details,
see 4.1.2 NE Functions.
7.1.3.4 Paging
When hybrid RAN sharing is used, TACs are planned at the cell level.
l Shared cells
You are advised to plan MMECs based on each operator's EPC. The MME's MMEC
must be unique in a TAC. The MMECs of different operators must be negotiated to
ensure this requirement is met. Otherwise, MMEC conflicts may occur.
l Non-shared cells
Plan an MMEC for the operator if the operator does not own any shared cell.
In hybrid RAN sharing, operators in a shared cell can be configured with the same MMEC if
paging errors due to MMEC conflicts are acceptable. For details, see 4.1.3.4 Paging.
7.1.3.5 Redirection
Redirection in hybrid RAN sharing is the same as that in RAN sharing with common carrier.
For details, see 4.1.3.5 Redirection.
Non-shared cells are not involved in fair sharing of air interface resources or intra-cell
operator-specific MLB because air interface resources are exclusively used by such cells.
Endpoint Mode
Table 7-1 Dedicated or shared transmission link configuration in endpoint mode for hybrid
RAN sharing
Transmission S1 with Dedicated S1 with Shared X2
Link MMEs MMEs
Table 7-2 Control-plane transmission link configuration in endpoint mode for hybrid RAN
sharing between carrier-sharing operator groups
Configuration S1 with Dedicated S1 with Shared X2
Item MMEs MMEs
Table 7-3 User-plane transmission link configuration in endpoint mode for hybrid RAN
sharing between carrier-sharing operator groups
Configuration S1 with Dedicated S1 with Shared S- X2
Item S-GWs GWs
Table 7-4 Control-plane transmission link configuration in endpoint mode for hybrid RAN
sharing within a carrier-sharing operator group
Configuration S1 with Dedicated S1 with Shared X2
Item MMEs MMEs
Table 7-5 User-plane transmission link configuration in endpoint mode for hybrid RAN
sharing within a carrier-sharing operator group
Configuration S1 with Dedicated S1 with Shared S- X2
Item S-GWs GWs
Link Mode
Table 7-6 Control-plane transmission link configuration in link mode for hybrid RAN sharing
between carrier-sharing operator groups
Transmission S1 with Shared S1 with Dedicated X2
Link MMEs MMEs
Table 7-7 User-plane transmission link configuration in link mode for hybrid RAN sharing
between carrier-sharing operator groups
Transmission S1 with Shared S- S1 with Dedicated X2
Link GWs S-GWs
Table 7-8 Control-plane transmission link configuration in link mode for hybrid RAN sharing
within a carrier-sharing operator group
Transmission S1 with Shared S1 with Dedicated X2
Link MMEs MMEs
Table 7-9 User-plane transmission link configuration in link mode for hybrid RAN sharing
within a carrier-sharing operator group
Transmission S1 with Shared S- S1 with Dedicated X2
Link GWs S-GWs
7.2.1 Benefits
The benefits are the same as those provided by RAN sharing with common carrier. For
details, see 4.2.1 Benefits.
7.2.2 Impacts
Network Impacts
If the UE distribution is different among RAN sharing operators, the throughput may change
after hybrid RAN sharing is enabled. The throughput is not affected if the UE distribution is
consistent among RAN sharing operators.
If the RB proportions vary greatly between the RAN sharing operators (for example, 9:1 for
two operators), UEs served by the operator with a smaller RB proportion experience a longer
scheduling delay after hybrid RAN sharing is enabled. However, the scheduling delay can still
meet the QoS requirements specified in section 6.1.7.2 "Standardized QCI characteristics" in
3GPP TS 23.203 V8.5.0.
After this function is enabled, handovers between RAN sharing operator groups under the
same eNodeB are treated as S1-based handovers. Therefore, this function increases the
number of inter-eNodeB handovers when operators (A and B) and operator B are in different
RAN sharing operator groups.
Function Impacts
RAT Function Function Switch Reference Description
Name
7.3 Requirements
7.3.1 Licenses
RAT Feature ID Feature Name Model Sales Unit
7.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Name Function Switch Reference Description
7.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
7.3.4 Others
None
Scenario-specific data for hybrid RAN sharing can be configured based on information
provided in Cell Management, Mobility Management in Connected Mode, and this section.
S1 ID S1.S1Id None
X2 ID X2.X2Id None
Local tracking CellOp.Tracki For example, when the eNodeB is shared by two
area ID ngAreaId operators in hybrid RAN sharing mode, a cell must
be configured with the tracking area IDs of both
operators, and the two tracking area IDs must
correspond to the same TAC.
In a cell where hybrid RAN sharing is enabled, the
CnOperatorTa.CnOperatorId values must be
different. One of the parameter values must
correspond to the primary operator of the RAN
sharing group.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a GERAN frequency based on the serving cell's PLMN.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a GERAN frequency based on the neighboring frequency's HPLMN.
Cell reselection GeranRanShar Set this parameter based on the network plan.
priority e.CellReselPrio
rity
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a UTRAN frequency based on the serving cell's PLMN.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a UTRAN frequency based on the neighboring frequency's HPLMN.
Cell reselection UtranRanShare. Set this parameter based on the network plan.
priority CellReselPriority
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for an E-UTRAN frequency based on the serving cell's PLMN.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for an E-UTRAN frequency based on the neighboring frequency's
HPLMN.
Cell reselection EutranNFreqRan Set this parameter based on the network plan.
priority Share.CellReselPr
iority
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a CDMA frequency based on the serving cell's PLMN.
The following provides the eNodeB- and operator-related MOs to be reconfigured. For details
about the parameters in the MOs and the parameter settings, see Parameters for Initial
Configuration.
iii. For other steps, see steps 2 through 9 in "Adding a secondary operator" in
Parameters for Reconfiguration of 4.4.1.1 Data Preparation.
– Remove a secondary operator.
i. Perform steps 1 through 8 in "Removing a secondary operator" in Parameters
for Reconfiguration of 4.4.1.1 Data Preparation.
ii. Use the CnOpSharingGroup MO to remove the mapping relationship
between the secondary operator and the RAN sharing operator group.
iii. (Optional) Use the CnOperator MO to remove the operator information.
l Changing the sharing mode of an eNodeB from the hybrid RAN sharing mode to the
independent operator mode
a. Remove all information related to RAN sharing operator groups. Retain all the
configurations about independent operators and remove the configurations of other
operators. For detailed operations, see steps 1 through 7 in "Removing a RAN
sharing operator group from hybrid RAN sharing operator groups."
b. Use the ENodeBSharingMode MO to set the eNodeB sharing mode to the
independent operator mode. After the modification, you need to run the RST APP
command to reset the application referenced by the eNodeB function for the
application to take effect (the application ID can be queried by running the LST
ENODEBFUNCTION command).
c. (Optional) Use the ENodeBAlgoSwitch.RanSharingAnrSwitch parameter to turn
off the ANR switch in the adjacent cells that have neighbor relationships with the
local cell.
CnOpSharingGroupId=1;
ADD X2INTERFACE: X2InterfaceId=0, X2CpBearerId=0, CnOperatorId=0,
CnOpSharingGroupId=0;
//Adding cells
ADD CELL: LocalCellId=0, CellName="LTE", CellId=0, PhyCellId=0,
FddTddInd=CELL_FDD, CnOpSharingGroupId=0;
//Configuring tracking area information for operators
ADD CNOPERATORTA: TrackingAreaId=0, CnOperatorId=0, Tac=33;
ADD CNOPERATORTA: TrackingAreaId=1, CnOperatorId=1, Tac=33;
//Configuring the mapping relationships between the cells and operator tracking
areas
ADD CELLOP: LocalCellId=0, TrackingAreaId=0,
CellReservedForOp=CELL_NOT_RESERVED_FOR_OP, OpUlRbUsedRatio=50,
OpDlRbUsedRatio=50, OpResourceGroupIndex=255, OperatorPlmnRoundPeriod=1;
ADD CELLOP: LocalCellId=0, TrackingAreaId=1,
CellReservedForOp=CELL_NOT_RESERVED_FOR_OP, OpUlRbUsedRatio=50,
OpDlRbUsedRatio=50, OpResourceGroupIndex=255, OperatorPlmnRoundPeriod=1;
ADD CELL: LocalCellId=1, CellName="LTE-1", CellId=0, PhyCellId=0,
FddTddInd=CELL_FDD, CnOpSharingGroupId=1;
ADD CNOPERATORTA: TrackingAreaId=2, CnOperatorId=2, Tac=33;
ADD CELLOP: LocalCellId=1, TrackingAreaId=2,
CellReservedForOp=CELL_NOT_RESERVED_FOR_OP;
//Resetting the application referenced by the eNodeB function for the application
to take effect (the application ID can be queried by running the LST
ENODEBFUNCTION command)
RST APP: AID=1;
Configuring a dedicated cell-reselection priority for a CDMA frequency (based on the serving
cell's PLMN)
ADD CDMA2000BCSCELLOP: LocalCellId=0, BandClass=bc0, CnOperatorID=0,
Cdma1XrttCellReselPriInd=NOT_CFG, HrpdCellReselDediPriCfgInd=NOT_CFG;
ADD CDMA2000BCSCELLOP: LocalCellId=0, BandClass=bc0, CnOperatorID=1,
Cdma1XrttCellReselPriInd=NOT_CFG, HrpdCellReselDediPriCfgInd=NOT_CFG;
Procedure
Step 1 Check the cell status by running the following commands:
DSP CELL:LOCALCELLID=0;
DSP CELL:LOCALCELLID=1;
Expected result:
The cell status is normal.
The following is an example of the command output for normal cell status:
--------------------------start--------------------------
%%/*34421*/DSP CELL: LOCALCELLID=0;%%
RETCODE = 0
Operation succeeded.
...
Local cell ID = 0
Cell instance state = Normal
...
%%/*34421*/DSP CELL: LOCALCELLID=1;%%
RETCODE = 0
Operation succeeded.
...
Local cell ID = 1
Cell instance state = Normal
...
--------------------------end---------------------------
Step 3 Power on UE 1 and UE 2 to initiate attach procedures towards the shared cell.
Expected result:
In the "tAI" IE in the S1AP_INITIAL_UE_MSG message traced on each S1 interface, the
values of "PLMNidentity" and "TAC" are consistent with the operator data. This indicates that
the UEs have successfully accessed the shared cell and selected the correct EPCs. In this
situation, the function has been activated successfully. The path of the "tAI" IE is S1ap-Msg
\initiatingMessage\value\initialUEMessage\protocolIEs\SEQUENCE\value\tAI.
The values of "PLMNidentity" and "TAC" in the traced message are mapped to the eNodeB
configurations as follows. The PLMN ID 46001 is used as an example.
l The MCC is 460 and MNC is F01 (F is added if there are fewer than three digits), which
are combined as 460F01. Then, each two adjacent digits exchange positions to get
64F010, which is the value of "PLMNidentity" in the traced message.
l The value of "TAC" is a hexadecimal number in the traced message.
----End
8.1 Principles
This function allows an eNodeB to be shared by up to six operators.
If this function is not enabled together with RAN sharing with common carrier, RAN sharing
with dedicated carrier, or hybrid RAN sharing is enabled, a maximum of four operators can
share the RAN.
8.2.1 Benefits
The benefits are the same as those provided by RAN sharing with common carrier. For
details, see 4.2.1 Benefits.
8.2.2 Impacts
Network Impacts
None
Function Impacts
None
8.3 Requirements
8.3.1 Licenses
In addition to the license required in a specific scenario, the operator has purchased and
activated the license for the feature listed in the following table.
8.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
8.3.3 Hardware
Boards
No requirements
RF Modules
No requirements
8.3.4 Others
None
l RAN sharing with common carrier in FDD: See 4.4.3 Network Monitoring.
l RAN sharing with dedicated carrier: See 5.4.3 Network Monitoring.
l RAN sharing with special dedicated carrier in FDD: See 6.4.3 Network Monitoring.
l Hybrid RAN sharing: See 7.4.3 Network Monitoring.
9.1 Principles
In RAN sharing scenarios, the licensed RRC_CONNECTED UE resources are allocated to
operators in proportions specified by the LicenseSharingPolicy.MaxUserNumRate
parameter. In addition, the fair user sharing function is introduced. In this function, the
LicenseSharingPolicy.UserNumSharingRate parameter controls what percentage of an
operator's resources can be shared with other operators when there are unused resources. Such
percentage of resources can also be shared between operators within the same
RRC_CONNECTED UE number sharing group. The sum of the values of the
LicenseSharingPolicy.MaxUserNumRate parameters for all operators cannot be greater than
100%. The value of the LicenseSharingPolicy.UserNumSharingRate parameter for any
operator cannot be greater than the value of the LicenseSharingPolicy.MaxUserNumRate
parameter for that operator.
NOTE
For details about the RRC_CONNECTED UE number sharing group, see 4.1.5.2 Capacity License.
9.2.1 Benefits
With this function, an operator in RAN sharing mode can share its unused allotment of
RRC_CONNECTED UE resources with another operator. RAN sharing modes include RAN
sharing with common carrier, RAN sharing with dedicated carrier, hybrid RAN sharing, and
RAN sharing with special dedicated carrier.
Other benefits are the same as those provided by RAN sharing with common carrier. For
details, see 4.2.1 Benefits.
9.2.2 Impacts
Network Impacts
When RRC_CONNECTED UE resources are partially or not shared among RAN sharing
operators, the maximum allowed number of RRC_CONNECTED UEs in shared cells cannot
be reached. This is because other operators cannot use or fully use the unused
RRC_CONNECTED UE resources of a certain operator.
Function Impacts
None
9.3 Requirements
9.3.1 Licenses
In addition to the license required in a specific scenario, the operator has purchased and
activated the license for the feature listed in the following table.
9.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
Function Name Function Reference Description
Switch
RAN sharing with ENodeBSharin RAN Sharing Fair user sharing requires
common carrier gMode.ENode that one of these features be
BSharingMode enabled.
9.3.3 Hardware
l BTS3911E
l BTS3203E
l BTS3202E
Boards
No requirements
RF Modules
No requirements
9.3.4 Others
None
Table 9-1 describes the parameters used for function activation specific to fair user sharing.
l RAN sharing with common carrier: See 4.4.1.2 Using MML Commands.
l RAN sharing with dedicated carrier: See 5.4.1.2 Using MML Commands.
l RAN sharing with special dedicated carrier: See 6.4.1.2 Using MML Commands.
l Hybrid RAN sharing: See 7.4.1.2 Using MML Commands.
l One of the prerequisite functions for fair user sharing has been activated.
l The total licensed number of RRC_CONNECTED UEs is 100, and RAN sharing is used
for operators A and B with the LicenseSharingPolicy.MaxUserNumRate parameter set
to 50 and the LicenseSharingPolicy.UserNumSharingRate parameter set to 20 for both
operators.
l 35 UEs of operators A and 60 UEs of operator B need to establish RRC connections.
Expected result:
RRC connections are established for all UEs of operator A and B. The excessive resources
used by UEs of operator B are offered by operator A.
To verify the activation of a prerequisite function, see section "Activation Verification" of a
specific function deployment scenario.
l RAN sharing with common carrier: See 4.4.2 Activation Verification.
l RAN sharing with dedicated carrier: See 5.4.2 Activation Verification.
l RAN sharing with special dedicated carrier: See 6.4.2 Activation Verification.
l Hybrid RAN sharing: See 7.4.2 Activation Verification.
10.1 Principles
In cells where RAN sharing with common carrier or hybrid RAN sharing is enabled, and in
cells of a secondary operator (involved in RAN sharing with special dedicated carrier),
common priorities for cell reselection are delivered through system information and are not
operator-specific. With this function, the cell-reselection priority can be configured on a per
operator basis. That is, different operators can be configured with different camping policies
for UEs in idle mode. For details, see 4.1.3.6 Cell Selection and Reselection.
Before sending information about the dedicated cell-reselection priority to a UE, the eNodeB
compares the CnOperatorID of the UE's serving PLMN with the CnOperatorID of a
neighboring frequency or frequency band configured for dedicated cell-reselection priorities
based on the serving cell's PLMN. If they are the same, the eNodeB includes the frequency or
frequency band in the information. Otherwise, the eNodeB does not do so.
When the eNodeB delivers the dedicated cell-reselection priority based on the serving cell's
PLMNs to the UE, the priority specified by the CellResel.CellReselPriority parameter is used
as the cell-reselection priority of the serving frequency.
Take two operators (A and B) as an example, where the dedicated cell-reselection priorities of
operator B are in an order opposite to those of operator A. The CellResel.CellReselPriority
parameter is 4, and the priorities required for operator A are, from highest to lowest:
l Serving frequency
l Neighboring E-UTRA frequency
10.2.1 Benefits
When this function is used together with RAN sharing with common carrier, RAN sharing
with dedicated carrier, RAN sharing with special dedicated carrier, or hybrid RAN sharing,
operators can configure dedicated cell reselection priorities based on the serving cell's PLMN
to provide operator-specific camping policies for UEs in idle mode.
Other benefits are the same as those provided by RAN sharing with common carrier. For
details, see 4.2.1 Benefits.
10.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
10.3 Requirements
10.3.1 Licenses
In addition to the license required in a specific scenario, the operator has purchased and
activated the license for the feature listed in the following table.
10.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
10.3.3 Hardware
Base Station Models
For FDD, the following base stations are compatible with this function:
l 3900 and 5900 series base stations
l DBS3900 LampSite and DBS5900 LampSite
l BTS3912E
l BTS3911E
l BTS3203E
l BTS3202E
Boards
No requirements
RF Modules
No requirements
10.3.4 Others
None
l RAN sharing with common carrier (FDD): See 4.4.1.1 Data Preparation.
l RAN sharing with dedicated carrier (FDD): See 5.4.1.1 Data Preparation.
l Hybrid RAN sharing (FDD): See 7.4.1.1 Data Preparation.
Before configuring data for MOCN cell reselection priority configuration, check whether
dedicated cell-reselection priorities based on the neighboring frequency's HPLMN have been
configured. If so, delete these settings.
The following tables describe the parameters specific to MOCN cell reselection priority
configuration.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a GERAN frequency based on the serving cell's PLMN.
Local cell ID CellReselGera Set this parameter to the same value as the Local Cell
n.LocalCellId ID parameter in the Cell MO.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a UTRAN frequency based on the serving cell's PLMN.
Local cell ID CellReselUtra Set this parameter to the same value as the Local Cell
n.LocalCellId ID parameter in the Cell MO.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for an E-UTRAN frequency based on the serving cell's PLMN.
Local cell ID CellResel.Loca Set this parameter to the same value as the Local Cell
lCellId ID parameter in the Cell MO.
The following table describes the parameters that must be set to configure the dedicated cell-
reselection priority for a CDMA frequency based on the serving cell's PLMN.
Local cell ID CellReselCdm Set this parameter to the same value as the Local Cell
a2000.LocalCel ID parameter in the Cell MO.
lId
11.1 Principles
In RAN sharing mode, the operators that share an eNodeB must jointly plan the SPIDs to
prevent SPID range overlaps among operators. With the multi-operator SPID policy function,
these operators can specify their own SPID ranges without the need to negotiate the SPID
ranges with one another.
Operator-specific SPID lists can be configured using the CnOperatorSpidCfg MO. Based on
these SPID lists, operators can configure their own SPID-based policies, for example, their
own dedicated cell reselection priorities. When releasing an RRC connection for a UE
configured with an SPID, the eNodeB checks whether a dedicated SPID list has been
configured for the operator. If so, the eNodeB queries the dedicated cell-reselection priority
corresponding to the UE's SPID and then delivers the queried information to the UE in an
RRC connection release message.
Since the operators sharing an eNodeB have their respective SPID lists, each operator can
allocate SPIDs without negotiating with one another. The SPID ranges from 1 to 256.
This function allows different operators to have a same SPID but different dedicated cell
reselection priorities on a shared eNodeB.
11.2.1 Benefits
In RAN sharing mode, operators can configure dedicated cell reselection priorities based on
respective dedicated SPID lists to provide operator-specific camping policies for UEs in idle
mode.
Other benefits are the same as those provided by RAN sharing with common carrier. For
details, see 4.2.1 Benefits.
11.2.2 Impacts
Network Impacts
None
Function Impacts
RAT Function Function Reference Description
Name Switch
11.3 Requirements
11.3.1 Licenses
In addition to the license required in a specific scenario, the operator has purchased and
activated the licenses for the features listed in the following table.
11.3.2 Software
Before activating this function, ensure that its prerequisite functions have been activated and
mutually exclusive functions have been deactivated. For detailed operations, see the relevant
feature documents.
Prerequisite Functions
RAT Function Function Reference Description
Name Switch
11.3.3 Hardware
l BTS3912E
l BTS3911E
l BTS3203E
l BTS3202E
Boards
No requirements
RF Modules
No requirements
11.3.4 Others
None
l RAN sharing with common carrier (FDD): See 4.4.1.1 Data Preparation.
l RAN sharing with dedicated carrier (FDD): See 5.4.1.1 Data Preparation.
l RAN sharing with special dedicated carrier (FDD): See 6.4.1.1 Data Preparation.
l Hybrid RAN sharing (FDD): See 7.4.1.1 Data Preparation.
Prerequisites
l RAN sharing with common carrier, RAN sharing with dedicated carrier, or hybrid RAN
sharing is enabled on the eNodeB.
l The SPID is configured based on the UE's serving PLMN, and a RAT/frequency priority
group is configured.
l Neighboring frequencies and external cells are configured. If RAN sharing with common
carrier is enabled in the external cells, the PLMNs of external cells must be configured.
Procedure
Step 1 Power on a UE for it to access an E-UTRAN cell and obtain the SPID.
After services on the UE are stopped for a while (20s by default), the eNodeB releases the UE
and instructs it to enter the idle mode by sending an RRC Connection Release message. The
dedicated cell-reselection priority information contained in the RRC Connection Release
message is consistent with the RAT/frequency priority group information corresponding to the
SPID configured on the eNodeB based on the UE's serving PLMN, as shown in Figure 11-2.
Step 3 Move the UE to the coverage area of neighboring cells. The UE reselects a neighboring cell
with the highest cell-reselection priority in the same way as it does normally.
----End
12 Parameters
License UserNu ADD TDLBF License Meaning: Indicates the ID of the sharing group of UEs
Sharing mSharin LICENS D-00401 Manage in RRC_CONNECTED mode. Operators with the
Policy gGroupI ESHAR 4 ment same UserNumSharingGroupId parameter value share
d INGPO LOFD-0 RAN the sum of the proportions of UEs in
LICY 01036/ Sharing RRC_CONNECTED mode of each operator and the
MOD TDLOF with sum of the penetration rates of UEs in
LICENS D-00103 Commo RRC_CONNECTED mode of each operator. The
ESHAR 6 n value 255 is an invalid ID, indicating that the operator
INGPO Carrier is not configured with a sharing group of UEs in
LOFD-0 RRC_CONNETED mode. This parameter applies
LICY 01037/ RAN only to LTE FDD and LTE TDD.
LST TDLOF Sharing
LICENS D-00103 with GUI Value Range: 1~6,255
ESHAR 7 Dedicate Unit: None
INGPO LOFD-0 d Actual Value Range: 1~6,255
LICY 70206 Carrier
Default Value: 255
Hybrid
RAN
Sharing
CellAlg OpReso MOD LOFD-0 RAN Meaning: Indicates whether to enable RAN sharing so
oSwitch urceGro CELLA 01036/ Sharing that admission and scheduling take effect in RAN
upShare LGOSW TDLOF with sharing mode. When the switch is on, operators share
Switch ITCH D-00103 Commo the resources specified by the RAN-sharing operator
LST 6 n group. When the OpPrbGroupshareSwitch option is
CELLA LOFD-0 Carrier selected, PRB resources can be shared by operator
LGOSW 70206/ Hybrid groups. This parameter applies only to LTE FDD and
ITCH TDLOF RAN LTE TDD.
D-08122 Sharing GUI Value Range: OpPrbGroupshareS-
4 witch(OpPrbGroupshareSwitch)
Unit: None
Actual Value Range: OpPrbGroupshareSwitch
Default Value: OpPrbGroupshareSwitch:Off
CellOp OpReso ADD LOFD-0 RAN Meaning: Indicates the index of the resource group to
urceGro CELLO 01036 Sharing which the operator belongs. The default value is 255,
upIndex P LOFD-0 with which indicates an invalid value. The
MOD 70206 Commo OpPrbGroupshareSwitch option takes effect only
CELLO n when operator sharing is set to a valid value.
P Carrier GUI Value Range: 0~5,255
LST Hybrid Unit: None
CELLO RAN
Sharing Actual Value Range: 0~5,255
P
Default Value: 255
CellAcc Broadca MOD LOFD-0 RAN Meaning: Indicates the public land mobile network
ess stMode CELLA 01036/ Sharing (PLMN) broadcast mode of the cell. If RAN sharing
CCESS TDLOF with with common carrier or hybrid RAN sharing is
LST D-00103 Commo enabled in certain cells on the live network and the
CELLA 6 n PLMN IDs are broadcast in rotation mode in least one
CCESS MLOFD Carrier of these cells, NBSLTEPLMNRoundSwitch under the
-121251 NB-IoT RanSharingAnrSwitch parameter must be selected for
RAN eNodeBs whose cells may be configured as
MLOFD neighboring cells for the local cell. Otherwise, the
-131253 Sharing
with local eNodeB may experience failures in handing over
MLBFD Commo UEs from the local cell to an ANR-established
-120002 n neighboring cell in which the PLMN IDs are
29 Carrier broadcast in rotation mode. If this parameter is set to
LOFD-0 NORMAL_MODE(Normal Mode), PLMN IDs are
NB-IoT broadcast in a fixed sequence in the cell. If this
70206/ Hybrid
TDLOF parameter is set to RR_MODE(Round Robin Mode),
RAN the PLMN ID at the top of the PLMN ID list is rotated
D-08122 Sharing
4 in RR mode at a cell-specific interval. If this
Broadca parameter is set to FREE_MODE(Free Mode), the
st of PLMN ID at the top of the PLMN ID list is rotated at
system an operator-specific interval. This parameter applies
informat only to LTE FDD and LTE TDD.
ion GUI Value Range: NORMAL_MODE(Normal
Hybrid Mode), RR_MODE(Round Robin Mode),
RAN FREE_MODE(Free Mode)
Sharing Unit: None
Actual Value Range: NORMAL_MODE, RR_MODE,
FREE_MODE
Default Value: NORMAL_MODE(Normal Mode)
ENodeB ENodeB MOD LOFD-0 RAN Meaning: Indicates the eNodeB sharing mode, which
Sharing Sharing ENODE 01036/ Sharing can be independent operator mode, RAN sharing with
Mode Mode BSHAR TDLOF with common carrier, RAN sharing with dedicated carrier,
INGMO D-00103 Commo hybrid RAN sharing, or RAN sharing with special
DE 6 n dedicated carrier.
LST MLOFD Carrier GUI Value Range: INDEPENDENT(Independent
ENODE -121251 NB-IoT Operator Mode), SHARED_FREQ(Shared Frequency
BSHAR LOFD-0 RAN Sharing Mode), SEPARATED_FREQ(Separate
INGMO 01037/ Sharing Frequency Sharing Mode),
DE TDLOF with HYBRID_SHARED(Hybrid RAN Sharing),
D-00103 Commo SEPARATED_FREQ_SPEC(Special Separate
7 n Frequency Sharing Mode)
Carrier Unit: None
MLOFD
-121252 RAN Actual Value Range: INDEPENDENT,
Sharing SHARED_FREQ, SEPARATED_FREQ,
MLOFD with
-131253 HYBRID_SHARED, SEPARATED_FREQ_SPEC
Dedicate
LOFD-0 d Default Value: INDEPENDENT(Independent
70206/ Carrier Operator Mode)
TDLOF NB-IoT
D-08122 RAN
4 Sharing
with
Dedicate
d
Carrier
NB-IoT
Hybrid
RAN
Sharing
Hybrid
RAN
Sharing
CnOper CnOper ADD LOFD-0 RAN Meaning: Indicates the type of the operator. The
ator atorType CNOPE 01036/ Sharing operator can be the primary operator or a secondary
RATOR TDLOF with operator. For each eNodeB, only one primary operator
MOD D-00103 Commo but more than one secondary operator can be
CNOPE 6 n configured.
RATOR MLOFD Carrier GUI Value Range:
LST -121251 NB-IoT CNOPERATOR_PRIMARY(Primary Operator),
CNOPE LOFD-0 RAN CNOPERATOR_SECONDARY(Secondary Operator)
RATOR 01037/ Sharing Unit: None
TDLOF with
Commo Actual Value Range: CNOPERATOR_PRIMARY,
D-00103 CNOPERATOR_SECONDARY
7 n
Carrier Default Value: None
MLOFD
-121252 RAN
Sharing
MLOFD with
-131253 Dedicate
LOFD-0 d
01086/ Carrier
TDLOF NB-IoT
D-00108 RAN
6 Sharing
LOFD-0 with
70206/ Dedicate
TDLOF d
D-08122 Carrier
4 NB-IoT
Hybrid
RAN
Sharing
RAN
Sharing
by More
Operator
s
Hybrid
RAN
Sharing
CellAcc CellBarr MOD LBFD-0 Cell Meaning: Indicates whether the cell is barred. If the
ess ed CELLA 02013/ Outage cell is barred, the UE cannot camp on the serving cell.
CCESS TDLBF Detectio During cell reselection, the serving cell is not selected
LST D-00203 n and as a candidate cell.
CELLA 7 Compen GUI Value Range: CELL_BARRED(Barred),
CCESS LBFD-0 sation CELL_NOT_BARRED(Not Barred)
02009/ Broadca Unit: None
TDLBF st of
D-00200 system Actual Value Range: CELL_BARRED,
9/ informat CELL_NOT_BARRED
MLBFD ion Default Value: CELL_NOT_BARRED(Not Barred)
-120002 RAN
29 Sharing
LOFD-0 with
01036/ Commo
TDLOF n
D-00103 Carrier
6
CnOper Tac ADD LOFD-0 RAN Meaning: Indicates the tracking area code (TAC),
atorTa CNOPE 01036/ Sharing which is used by the EPC to determine the area within
RATOR TDLOF with which paging messages are sent. One tracking area is
TA D-00103 Commo comprised of one or more cells.
MOD 6 n GUI Value Range: 1~65533,65535
CNOPE MLOFD Carrier
Unit: None
RATOR -121251 NB-IoT
TA RAN Actual Value Range: 1~65533,65535
LOFD-0
LST 01037/ Sharing Default Value: None
CNOPE TDLOF with
RATOR D-00103 Commo
TA 7 n
Carrier
MLOFD
-121252 RAN
Sharing
LOFD-0 with
70206/ Dedicate
TDLOF d
D-08122 Carrier
4
NB-IoT
MLOFD RAN
-131253 Sharing
with
Dedicate
d
Carrier
Hybrid
RAN
Sharing
NB-IoT
Hybrid
RAN
Sharing
CnOper Trackin ADD LOFD-0 RAN Meaning: Indicates the tracking area ID, which
atorTa gAreaId CNOPE 01036/ Sharing uniquely identifies an entry of tracking area
RATOR TDLOF with information. This parameter is used only within the
TA D-00103 Commo eNodeB and is not used during the information
LST 6 n exchange with the EPC. This is different from the TAI
CNOPE MLOFD Carrier configured in the EPC TAL.
RATOR -121251 NB-IoT GUI Value Range: 0~65535
TA LOFD-0 RAN Unit: None
MOD 01037/ Sharing
with Actual Value Range: 0~65535
CNOPE TDLOF
RATOR D-00103 Commo Default Value: None
TA 7 n
Carrier
RMV MLOFD
CNOPE -121252 RAN
RATOR Sharing
LOFD-0 with
TA 70206/ Dedicate
TDLOF d
D-08122 Carrier
4
NB-IoT
MLBFD RAN
-120002 Sharing
29 with
MLBFD Dedicate
-120002 d
37 Carrier
MLOFD Hybrid
-131253 RAN
Sharing
Broadca
st of
system
informat
ion
Cell
Selectio
n and
Re-
selection
NB-IoT
Hybrid
RAN
Sharing
CellAcc RoundP MOD LOFD-0 RAN Meaning: Indicates the changing period of cell
ess eriod CELLA 01036/ Sharing PLMN.
CCESS TDLOF with GUI Value Range: 1~720
LST D-00103 Commo
6 n Unit: h
CELLA
CCESS MLOFD Carrier Actual Value Range: 1~720
-121251 NB-IoT Default Value: 1
MLOFD RAN
-131253 Sharing
with
MLBFD Commo
-120002 n
29 Carrier
LOFD-0 NB-IoT
70206/ Hybrid
TDLOF RAN
D-08122 Sharing
4
Broadca
st of
system
informat
ion
Hybrid
RAN
Sharing
CellAcc RoundA MOD LOFD-0 RAN Meaning: Indicates the start time for broadcasting
ess ctionTi CELLA 01036/ Sharing PLMN-specific information in round robin mode.
me CCESS TDLOF with GUI Value Range:
LST D-00103 Commo 2000-01-01T00:00:00+00:00~2099-12-31T23:59:59+
CELLA 6 n 00:00
CCESS MLOFD Carrier
Unit: None
-121251 NB-IoT
RAN Actual Value Range:
MLOFD 2000-01-01T00:00:00+00:00~2099-12-31T23:59:59+
-131253 Sharing
with 00:00
LOFD-0 Commo Default Value: 2000-01-01T00:00:00+00:00
70206/ n
TDLOF Carrier
D-08122
4 NB-IoT
Hybrid
RAN
Sharing
Hybrid
RAN
Sharing
CellOp Operator ADD LOFD-0 RAN Meaning: Indicates the operator-level PLMN
PlmnRo CELLO 01036/ Sharing broadcast round-robin period.
undPeri P TDLOF with GUI Value Range: 1~720
od MOD D-00103 Commo
6 n Unit: h
CELLO
P MLOFD Carrier Actual Value Range: 1~720
GlobalP DiffOp MOD LBFD-0 S1-flex Meaning: Indicates whether MMEs of operators that
rocSwitc WithSa GLOBA 01018/ RAN share the eNodeB can be configured with the same
h meMme LPROC TDLBF Sharing mobility management entity code (MMEC). If this
cSwitch SWITC D-00101 with parameter is set to OFF(Off), MMEs of operators that
H 8 Commo share the eNodeB cannot be configured with the same
LST LOFD-0 n MMEC. If this parameter is set to ON(On), MMEs of
GLOBA 01036/ Carrier operators that share the eNodeB can be configured
LPROC TDLOF with the same MMEC.
Hybrid
SWITC D-00103 RAN GUI Value Range: OFF(Off), ON(On)
H 6 Sharing Unit: None
LOFD-0 Actual Value Range: OFF, ON
70206/
TDLOF Default Value: OFF(Off)
D-08122
4
RatFreq RatFreq ADD LOFD-0 Camp & Meaning: Indicates the ID of the RAT/frequency
Priority Priority RATFR 0105401 Handov priority group. This parameter applies only to LTE
Group GroupId EQPRI / er Based FDD and LTE TDD.
ORITY TDLOF on SPID GUI Value Range: 0~255
GROUP D-00105
401 Unit: None
LST
RATFR Actual Value Range: 0~255
EQPRI Default Value: None
ORITY
GROUP
MOD
RATFR
EQPRI
ORITY
GROUP
RMV
RATFR
EQPRI
ORITY
GROUP
SpidCfg Spid ADD LOFD-0 Camp & Meaning: Indicates the subscriber profile ID (SPID).
SPIDCF 0105401 Handov According to 3GPP specifications, the SPID can be
G / er Based from 1 to 256. When this parameter is set to 0, the
LST TDLOF on SPID eNodeB does not obtain the SPID from the MME or
SPIDCF D-00105 UL Pre- the eNodeB is not configured with an SPID for UEs.
G 401 allocatio This parameter applies only to LTE FDD and LTE
LOFD-0 n Based TDD.
MOD
SPIDCF 01059/ on SPID GUI Value Range: 0~256
G TDLOF Unit: None
D-00105
RMV 9 Actual Value Range: 0~256
SPIDCF Default Value: None
G
SpidCfg RatFreq ADD LOFD-0 Camp & Meaning: Indicates the ID of the intra-RAT frequency
Priority SPIDCF 0105401 Handov priority group. This parameter applies only to LTE
GroupId G / er Based FDD and LTE TDD.
MOD TDLOF on SPID GUI Value Range: 0~255
SPIDCF D-00105 RAN
401 Unit: None
G Sharing
LOFD-0 with Actual Value Range: 0~255
LST
SPIDCF 01036/ Commo Default Value: 0
G TDLOF n
D-00103 Carrier
6
ServiceBasedInterFreqHoSwitch, UlQualityInterFreq-
HoSwitch, CSFBLoadInfoSwitch,
Cdma1XrttEcsfbSwitch, EmcBlindHoA1Switch,
EmcInterFreqBlindHoSwitch, EPlmnSwitch,
ServiceReqInterFreqHoSwitch,
VoipHoControlSwitch, UtranUltraFlashCsfbSwitch,
GeranUltraFlashCsfbSwitch, RatLayerSwitch,
ServiceBasedMultiFreqHoSwitch, SrvccRatSteeringS-
witch, PsRatSteeringSwitch
Default Value: IntraFreqCoverHoSwitch:On,
InterFreqCoverHoSwitch:On,
Cdma1xRttCsfbSwitch:Off, UtranServiceHoS-
witch:Off, GeranServiceHoSwitch:Off,
UlQualityInterRATHoSwitch:Off,
InterPlmnHoSwitch:Off, ServiceBasedInterFreqHoS-
witch:Off, UlQualityInterFreqHoSwitch:Off,
CSFBLoadInfoSwitch:Off,
Cdma1XrttEcsfbSwitch:Off,
EmcBlindHoA1Switch:Off, EmcInterFreqBlindHoS-
witch:Off, EPlmnSwitch:Off, ServiceReqInterFreq-
HoSwitch:Off, VoipHoControlSwitch:Off,
UtranUltraFlashCsfbSwitch:Off,
GeranUltraFlashCsfbSwitch:Off, RatLayerSwitch:Off,
ServiceBasedMultiFreqHoSwitch:Off,
SrvccRatSteeringSwitch:Off,
PsRatSteeringSwitch:Off
InterPlm CnOper ADD None None Meaning: Indicates the index of the operator. This
nHoList atorId INTERP parameter applies only to LTE FDD and LTE TDD.
LMNH GUI Value Range: 0~5
OLIST
Unit: None
LST
INTERP Actual Value Range: 0~5
LMNH Default Value: None
OLIST
RMV
INTERP
LMNH
OLIST
InterPlm TarMcc ADD LBFD-0 Coverag Meaning: Indicates the mobile country code of the
nHoList INTERP 0201801 e Based target PLMN. This parameter applies only to LTE
LMNH / Intra- FDD and LTE TDD.
OLIST TDLBF frequenc GUI Value Range: 3 characters
LST D-00201 y
801 Handov Unit: None
INTERP
LMNH LBFD-0 er Actual Value Range: 000~999
OLIST 0201802 Coverag Default Value: None
RMV / e Based
INTERP TDLBF Inter-
LMNH D-00201 frequenc
OLIST 802 y
LBFD-0 Handov
0201804 er
/ Distance
TDLBF Based
D-00201 Inter-
804 frequenc
LBFD-0 y
0201805 Handov
/ er
TDLBF Service
D-00201 Based
805 Inter-
LOFD-0 frequenc
01019/ y
TDLOF Handov
D-00101 er
9 PS Inter-
LOFD-0 RAT
01020/ Mobility
TDLOF between
D-00102 E-
0 UTRAN
and
LOFD-0 UTRAN
01033/
TDLOF PS Inter-
D-00103 RAT
3 Mobility
between
E-
UTRAN
and
GERAN
CS
Fallback
to
UTRAN
InterPlm TarMnc ADD LBFD-0 Coverag Meaning: Indicates the mobile network code of the
nHoList INTERP 0201801 e Based target PLMN. This parameter applies only to LTE
LMNH / Intra- FDD and LTE TDD.
OLIST TDLBF frequenc GUI Value Range: 2~3 characters
LST D-00201 y
801 Handov Unit: None
INTERP
LMNH LBFD-0 er Actual Value Range: 00~99,000~999
OLIST 0201802 Coverag Default Value: None
RMV / e Based
INTERP TDLBF Inter-
LMNH D-00201 frequenc
OLIST 802 y
LBFD-0 Handov
0201804 er
/ Distance
TDLBF Based
D-00201 Inter-
804 frequenc
LBFD-0 y
0201805 Handov
/ er
TDLBF Service
D-00201 Based
805 Inter-
LOFD-0 frequenc
01019/ y
TDLOF Handov
D-00101 er
9 PS Inter-
LOFD-0 RAT
01020/ Mobility
TDLOF between
D-00102 E-
0 UTRAN
and
LOFD-0 UTRAN
01033/
TDLOF PS Inter-
D-00103 RAT
3 Mobility
between
E-
UTRAN
and
GERAN
CS
Fallback
to
UTRAN
License MaxUse ADD LOFD-0 RAN Meaning: Indicates the proportion of the number of
Sharing rNumRa LICENS 01036/ Sharing UEs in RRC_CONNECTED mode of the operator
Policy te ESHAR TDLOF with when the eNodeB is shared among operators. This
INGPO D-00103 Commo parameter must be set based on the contract signed
LICY 6 n with operators. This parameter applies only to LTE
MOD LOFD-0 Carrier FDD and LTE TDD.
LICENS 01037/ RAN GUI Value Range: 1~100
ESHAR TDLOF Sharing Unit: %
INGPO D-00103 with
LICY 7 Dedicate Actual Value Range: 1~100
LicRatio TrafficS MOD LOFD-0 RAN Meaning: Indicates the mode of traffic sharing
haringT LICRAT 01036/ Sharing between the operators in RAN sharing scenarios. If
ype IO TDLOF with this parameter is set to SHARING, all the operators
LST D-00103 Commo share the total traffic of the eNodeB without
LICRAT 6 n proportional limits. If this parameter is set to
IO LOFD-0 Carrier DEDICATE and the ENodeBSharingMode parameter
01037/ RAN is not set to INDEPENDENT, all the operators share
TDLOF Sharing the total traffic of the eNodeB based on specific
D-00103 with proportions. However, the vacant traffic of an operator
7 Dedicate can be used by other operators. This parameter applies
d only to LTE FDD and LTE TDD.
LOFD-0
70206/ Carrier GUI Value Range: SHARING(Sharing),
TDLOF Hybrid DEDICATE(Dedicate)
D-08122 RAN Unit: None
4 Sharing Actual Value Range: SHARING, DEDICATE
Default Value: SHARING(Sharing)
LicRatio TrfRatio ADD LOFD-0 RAN Meaning: Indicates the proportion of traffic used by
SharePo LICRAT 01036/ Sharing the operator when the eNodeB is shared among
licy IOSHA TDLOF with operators. This parameter must be set based on the
REPOLI D-00103 Commo contract signed by operators. If this parameter is set to
CY 6 n 0, services except emergency calls of this operator are
MOD LOFD-0 Carrier not admitted.
LICRAT 01037/ RAN GUI Value Range: 0~100
IOSHA TDLOF Sharing Unit: %
REPOLI D-00103 with
CY 7 Dedicate Actual Value Range: 0~100
LicRatio TrfShari ADD LOFD-0 RAN Meaning: Indicates the proportion of traffic that the
SharePo ngRatio LICRAT 01036/ Sharing operator can share with other operators when the
licy IOSHA TDLOF with eNodeB is shared among operators.
REPOLI D-00103 Commo GUI Value Range: 0~100
CY 6 n
Carrier Unit: %
MOD LOFD-0
LICRAT 70206/ Hybrid Actual Value Range: 0~100
IOSHA TDLOF RAN Default Value: 0
REPOLI D-08122 Sharing
CY 4 RAN
LST LOFD-0 Sharing
LICRAT 01037/ with
IOSHA TDLOF Dedicate
REPOLI D-00103 d
CY 7 Carrier
CellAlg RanShar MOD LOFD-0 RAN Meaning: Indicates whether admission control,
oSwitch eModeS CELLA 01036/ Sharing congestion control, and scheduling policies are
witch LGOSW TDLOF with operator-specific. If this switch is turned on,
ITCH D-00103 Commo admission control, congestion control, and scheduling
LST 6 n policies are operator-specific. On FDD and TDD
CELLA LOFD-0 Carrier networks, operators share data channel resources
LGOSW 01112/ MOCN according to the specified RB percentages. On NB-
ITCH TDLOF Flexible IoT networks, operators share UE context storage
D-00111 Priority resources according to the specified percentages. If
2 Based this switch is turned off, admission control, congestion
Campin control, and scheduling policies are not operator-
LOFD-0 specific.
70206/ g
TDLOF Hybrid GUI Value Range: OFF(Off), ON(On),
D-08122 RAN STATIC_SHARING(STATIC_SHARING)
4 Sharing Unit: None
Actual Value Range: OFF, ON, STATIC_SHARING
Default Value: OFF(Off)
CellOp OpDlRb ADD LOFD-0 RAN Meaning: Indicates the percentage of resource blocks
UsedRat CELLO 01036/ Sharing (RBs) occupied by the operator on the physical
io P TDLOF with downlink shared channel (PDSCH) when RAN
MOD D-00103 Commo sharing is enabled on the eNodeB and the
CELLO 6 n RanShareModeSwitch parameter of the
P LBFD-0 Carrier CellAlgoSwitch MO is set to ON(On). If the data
02009/ Broadca volume is sufficient, the percentage of RBs occupied
LST by each operator will reach the preset value.
CELLO TDLBF st of
D-00200 system Modifications on this parameter affect the percentage
P of RBs occupied by operators on the PDSCH. When
9 informat
ion the OpPrbGroupshareSwitch option is selected in
LOFD-0 RAN sharing mode, this parameter is used to calculate
70206/ Hybrid the percentage of RBs occupied by the operator
TDLOF RAN resource group on the PDSCH. The percentage of RBs
D-08122 Sharing occupied by an operator resource group is the sum of
4 percentages of RBs occupied by operators in the
group. This parameter takes effect only in RAN
sharing with common carrier mode or in hybrid RAN
sharing mode with more than one CellOp MO being
configured. This parameter applies only to LTE FDD
and LTE TDD.
GUI Value Range: 1~100
Unit: %
Actual Value Range: 1~100
Default Value: 16
CellOp OpUlRb ADD LOFD-0 RAN Meaning: Indicates the percentage of resource blocks
UsedRat CELLO 01036/ Sharing (RBs) occupied by the operator on the physical uplink
io P TDLOF with shared channel (PUSCH) when RAN sharing is
MOD D-00103 Commo enabled on the eNodeB and the RanShareModeSwitch
CELLO 6 n parameter of the CellAlgoSwitch MO is set to
P LBFD-0 Carrier ON(On). If the data volume is sufficient, the
02009/ Broadca percentage of RBs occupied by each operator will
LST reach the preset value. Modifications on this
CELLO TDLBF st of
D-00200 system parameter affect the percentages of RBs occupied by
P operators on the PUSCH. When the
9 informat
ion OpPrbGroupshareSwitch option is selected in RAN
LOFD-0 sharing mode, this parameter is used to calculate the
70206/ Hybrid percentage of RBs occupied by the operator resource
TDLOF RAN group on the PUSCH. The percentage of RBs
D-08122 Sharing occupied by an operator resource group is the sum of
4 percentages of RBs occupied by operators in the
group. This parameter takes effect only in RAN
sharing with common carrier mode or in hybrid RAN
sharing mode with more than one CellOp MO being
configured. This parameter applies only to LTE FDD
and LTE TDD.
GUI Value Range: 1~100
Unit: %
Actual Value Range: 1~100
Default Value: 16
GTRAN EPCFG SET LBFD-0 Self- Meaning: Indicates the configuration mode of an end
SPARA MODE GTRAN 02035 configur point object, including S1SIMPLE_MODE(S1 Simple
SPARA ation Mode), X2SIMPLE_MODE(X2 Simple Mode) and
FBFD-0 EX2SIMPLE_MODE(eX2 Simple Mode). This
LST 10016 Transmi
GTRAN parameter can be set to one or multiple values. The
ssion parameter takes effect only in LTE.
SPARA Network
ing GUI Value Range: S1SIMPLE_MODE(S1 Simple
Mode), X2SIMPLE_MODE(X2 Simple Mode),
EX2SIMPLE_MODE(eX2 Simple Mode)
Unit: None
Actual Value Range: S1SIMPLE_MODE,
X2SIMPLE_MODE, EX2SIMPLE_MODE
Default Value: S1SIMPLE_MODE:0,
X2SIMPLE_MODE:0, EX2SIMPLE_MODE:0
Unit: None
Actual Value Range: SpsSchSwitch,
SinrAdjustSwitch, PreAllocationSwitch,
UlVmimoSwitch, TtiBundlingSwitch,
SmartPreAllocationSwitch, PuschDtxSwitch,
UlIblerAdjustSwitch, UlEnhancedFssSwitch,
UlEnhancedSrSchSwitch, SchedulerCtrlPowerSwitch,
UlIicsAlgoSwitch, UlMinGbrSwitch,
UlMbrCtrlSwitch, MbrUlSchSwitch,
UeAmbrUlSchSwitch, UlEnhancedDopplerSwitch,
UlRaUserSchOptSw, UlLast2RetransSchOptSwitch,
UlInterfFssSwitch, UlSmallRBSpectralEffOptSw,
PuschUsePucchRbSwitch, PuschDtxSchOptSwitch,
ULFSSAlgoSwitch, PrachRbReuseSwitch,
SrSchDataAdptSw, UlFssUserThdStSwitch,
HighOrderVMIMOSwitch, VMIMOReduceMCSRi-
seRBSwitch, VoLTEUeVmimoSwitch,
TtiBundlingForVideoSwitch
Default Value: SpsSchSwitch:Off,
SinrAdjustSwitch:On, PreAllocationSwitch:On,
UlVmimoSwitch:Off, TtiBundlingSwitch:Off,
SmartPreAllocationSwitch:On, PuschDtxSwitch:On,
UlIblerAdjustSwitch:Off, UlEnhancedFssSwitch:On,
UlEnhancedSrSchSwitch:On, SchedulerCtrlPowerS-
witch:Off, UlIicsAlgoSwitch:Off,
UlMinGbrSwitch:Off, UlMbrCtrlSwitch:Off,
MbrUlSchSwitch:Off, UeAmbrUlSchSwitch:Off,
UlEnhancedDopplerSwitch:On,
UlRaUserSchOptSw:Off,
UlLast2RetransSchOptSwitch:On,
UlInterfFssSwitch:Off, UlSmallRBSpectralEf-
fOptSw:Off, PuschUsePucchRbSwitch:Off,
PuschDtxSchOptSwitch:Off, ULFSSAlgoSwitch:On,
PrachRbReuseSwitch:Off, SrSchDataAdptSw:On,
UlFssUserThdStSwitch:Off, HighOrderVMIMOS-
witch:Off, VMIMOReduceMCSRiseRBSwitch:Off,
VoLTEUeVmimoSwitch:Off, TtiBundlingForVideoS-
witch:Off
EpfEnhancedSwitch(EpfEnhancedSwitch),
AperiodicCqiTrigOptSwitch(AperiodicCqiTrigOptS-
witch), VoipTbsBasedMcsSelS-
witch(VoipTbsBasedMcsSelSwitch),
PagingInterfRandSwitch(PagingInterfRandSwitch),
DlSingleUsrMcsOptSwitch(DlSingleUsrMcsOptS-
witch), SubframeSchDiffSwitch(SubframeSchDiffS-
witch), TailPackagePriSchS-
witch(TailPackagePriSchSwitch),
UeSigMcsEnhanceSwitch(UeSigMcsEnhanceSwitch),
FreqSelJudgeIgnorDopplerSwitch(FreqSelJudgeIgnor-
DopplerSwitch),
SIB1InterfRandSwitch(SIB1InterfRandSwitch),
EnhExtQCISpsSchSwitch(EnhExtQCISpsSchSwitch),
DlVoipBundlingSwitch(DlVoipBundlingSwitch),
DlPacketLenAwareSchSw(DlPacketLenAwar-
eSchSw), RLCArqFeedbackEnhanced-
Switch(RLCArqFeedbackEnhancedSwitch),
PaReconfigOptSwitch(PaReconfigOptSwitch),
RankRapidRptSwitch(RankRapidRptSwitch),
DlRLCStateReportSchDe-
laySw(DlRLCStateReportSchDelaySw),
SmallPktMcsSelectAlgoSw(SmallPktMcsSelectAl-
goSw), SRB0SplitSchSw(SRB0SplitSchSw),
BfUserPairPriorSwitch(BfUserPairPriorSwitch),
HarqAllocOptSwitch(HarqAllocOptSwitch),
Pusch32Switch(Pusch32Switch),
DlPreciseAmbrCtrlSwitch(DlPreciseAmbrCtrlSwitch)
Unit: None
Actual Value Range: FreqSelSwitch, SpsSchSwitch,
MBSFNShutDownSwitch, NonGbrBundlingSwitch,
EnAperiodicCqiRptSwitch, DlMbrCtrlSwitch,
MbrDlSchSwitch, UeAmbrDlSchSwitch,
EpfEnhancedSwitch, AperiodicCqiTrigOptSwitch,
VoipTbsBasedMcsSelSwitch, PagingInterfRand-
Switch, DlSingleUsrMcsOptSwitch,
SubframeSchDiffSwitch, TailPackagePriSchSwitch,
UeSigMcsEnhanceSwitch, FreqSelJudgeIgnorDop-
plerSwitch, SIB1InterfRandSwitch,
EnhExtQCISpsSchSwitch, DlVoipBundlingSwitch,
DlPacketLenAwareSchSw, RLCArqFeedbackEnhan-
cedSwitch, PaReconfigOptSwitch,
RankRapidRptSwitch, DlRLCStateReportSchDe-
laySw, SmallPktMcsSelectAlgoSw, SRB0SplitSchSw,
BfUserPairPriorSwitch, HarqAllocOptSwitch,
Pusch32Switch, DlPreciseAmbrCtrlSwitch
Default Value: FreqSelSwitch:Off, SpsSchSwitch:Off,
MBSFNShutDownSwitch:Off, NonGbrBundlingS-
CellWtt PrbUpLi MOD LOFD-1 WBB Meaning: Indicates the PRB threshold control mode.
xParaCf mitCtrl CELLW 10223/ User This parameter provides the TIGHT_CONTROL and
g Mode TTXPA TDLOF Steering MBB_LOOSE_CONTROL modes. When this
RACFG D-11022 Manage parameter is set to TIGHT_CONTROL, the upper
LST 3 ment limit of PRB resources for WBB and MBB UEs are
CELLW subject to the uplink and downlink PRB threshold
TTXPA policies. That is, the PRB resources for WBB and
RACFG MBB UEs must not exceed the upper limit even if
there are spare PRB resources. When this parameter is
set to MBB_LOOSE_CONTROL, the PRB resources
for MBB UEs can exceed the preset upper limit if
PRB resources are not exhausted after meeting the
requirements for scheduling WBB UEs. In this
situation, MBB UEs are allowed to use spare PRB
resources in the cell. The TIGHT_CONTROL policy
still applies to WBB UEs. This parameter applies only
to LTE FDD and LTE TDD.
GUI Value Range: TIGHT_CONTROL,
MBB_LOOSE_CONTROL
Unit: None
Actual Value Range: TIGHT_CONTROL,
MBB_LOOSE_CONTROL
Default Value: MBB_LOOSE_CONTROL
witch), FDDHetNetDlCompS-
witch(FDDHetNetDlCompSwitch),
IntraDlCompJtSwitch(IntraDlCompJtSwitch)
Unit: None
Actual Value Range: IntraDlCompSwitch,
InterDlCompDcsSwitch, InterDlCompCbfSwitch,
FDDHomNetDlCompSwitch, FDDHetNetDlCompS-
witch, IntraDlCompJtSwitch
Default Value: IntraDlCompSwitch:Off,
InterDlCompDcsSwitch:Off, InterDlCompCbfS-
witch:Off, FDDHomNetDlCompSwitch:Off,
FDDHetNetDlCompSwitch:Off,
IntraDlCompJtSwitch:Off
CspcAlg CspcAlg MOD LOFD-0 Coordin Meaning: Indicates whether to enable CSPC in cells
oPara oSwitch CSPCA 70208 ated under the centralized control node in Cloud BB
LGOPA TDLOF Scheduli scenarios. This parameter applies only to LTE FDD.
RA D-08020 ng based GUI Value Range: OFF(Off), ON(On)
LST 3 Power
Control Unit: None
CSPCA
LGOPA Coordin Actual Value Range: OFF, ON
RA ated Default Value: OFF(Off)
Scheduli
ng based
Power
Control
CnOper CnOper ADD LOFD-0 RAN Meaning: Indicates the ID of the operator.
atorTa atorId CNOPE 01036/ Sharing GUI Value Range: 0~5
RATOR TDLOF with
TA D-00103 Commo Unit: None
CellOp LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
llId CELLO identifies a cell within an eNodeB.
P GUI Value Range: 0~255
DSP Unit: None
CELLB
ROADC Actual Value Range: 0~255
ASTCN Default Value: None
OPERA
TOR
LST
CELLO
P
MOD
CELLO
P
RMV
CELLO
P
CnOper CnOper ADD LOFD-0 RAN Meaning: Indicates the ID of the operator.
ator atorId CNOPE 01036/ Sharing GUI Value Range: 0~5
RATOR TDLOF with
D-00103 Commo Unit: None
LST
CNOPE 6 n Actual Value Range: 0~5
RATOR MLOFD Carrier Default Value: None
MOD -121251 NB-IoT
CNOPE LOFD-0 RAN
RATOR 01037/ Sharing
TDLOF with
RMV Commo
CNOPE D-00103
7 n
RATOR Carrier
MLOFD
-121252 RAN
Sharing
MLOFD with
-131253 Dedicate
LOFD-0 d
01086/ Carrier
TDLOF NB-IoT
D-00108 RAN
6 Sharing
LOFD-0 with
70206/ Dedicate
TDLOF d
D-08122 Carrier
4 NB-IoT
Hybrid
RAN
Sharing
RAN
Sharing
by More
Operator
s
Hybrid
RAN
Sharing
CnOper CnOper ADD LOFD-0 RAN Meaning: Indicates the name of the operator.
ator atorNam CNOPE 01036/ Sharing GUI Value Range: 1~32 characters
e RATOR TDLOF with
D-00103 Commo Unit: None
MOD
CNOPE 6 n Actual Value Range: 1~32 characters
RATOR MLOFD Carrier Default Value: None
LST -121251 NB-IoT
CNOPE LOFD-0 RAN
RATOR 01037/ Sharing
TDLOF with
D-00103 Commo
7 n
Carrier
MLOFD
-121252 RAN
Sharing
MLOFD with
-131253 Dedicate
LOFD-0 d
01086/ Carrier
TDLOF NB-IoT
D-00108 RAN
6 Sharing
LOFD-0 with
70206/ Dedicate
TDLOF d
D-08122 Carrier
4 NB-IoT
Hybrid
RAN
Sharing
RAN
Sharing
by More
Operator
s
Hybrid
RAN
Sharing
CnOper Mcc ADD LOFD-0 RAN Meaning: Indicates the mobile country code (MCC) of
ator CNOPE 01036/ Sharing the operator.
RATOR TDLOF with GUI Value Range: 3 characters
MOD D-00103 Commo
6 n Unit: None
CNOPE
RATOR MLOFD Carrier Actual Value Range: 000~999
CnOper Mnc ADD LOFD-0 RAN Meaning: Indicates the mobile network code (MNC)
ator CNOPE 01036/ Sharing of the operator. The value of this parameter is a string
RATOR TDLOF with of two or three decimal digits.
MOD D-00103 Commo GUI Value Range: 2~3 characters
CNOPE 6 n
Carrier Unit: None
RATOR MLOFD
-121251 NB-IoT Actual Value Range: 00~99,000~999
LST
CNOPE LOFD-0 RAN Default Value: None
RATOR 01037/ Sharing
TDLOF with
D-00103 Commo
7 n
Carrier
MLOFD
-121252 RAN
Sharing
MLOFD with
-131253 Dedicate
LOFD-0 d
01086/ Carrier
TDLOF NB-IoT
D-00108 RAN
6 Sharing
LOFD-0 with
70206/ Dedicate
TDLOF d
D-08122 Carrier
4 NB-IoT
Hybrid
RAN
Sharing
RAN
Sharing
by More
Operator
s
Hybrid
RAN
Sharing
CellAcc LocalCe LST None None Meaning: Indicates the local ID of the cell. It uniquely
ess llId CELLA identifies a cell within a BS.
CCESS GUI Value Range: 0~255
MOD Unit: None
CELLA
CCESS Actual Value Range: 0~255
Default Value: None
License CnOper ADD LOFD-0 RAN Meaning: Indicates the index of the operator. This
Sharing atorId LICENS 01036/ Sharing parameter applies only to LTE FDD and LTE TDD.
Policy ESHAR TDLOF with GUI Value Range: 0~5
INGPO D-00103 Commo
LICY 6 n Unit: None
CellAlg LocalCe DSP None None Meaning: Indicates the local ID of the cell. It uniquely
oSwitch llId CELLU identifies a cell within an eNodeB.
LCAMC GUI Value Range: 0~255
CLUST
ER Unit: None
LicRatio UpLicR MOD LOFD-0 RAN Meaning: Indicates the proportion of the UL licensed
atio LICRAT 01036/ Sharing traffic to the total licensed traffic of the eNodeB. The
IO TDLOF with total licensed traffic is the sum of UL and DL licensed
LST D-00103 Commo traffic. If this parameter is set to 100%, there is no DL
LICRAT 6 n licensed traffic, affecting service admission. This
IO LOFD-0 Carrier parameter applies only to LTE FDD and LTE TDD.
01037/ RAN GUI Value Range: 1~100
TDLOF Sharing Unit: %
D-00103 with
7 Dedicate Actual Value Range: 1~100
LicRatio CnOper ADD LOFD-0 RAN Meaning: Indicates the ID of the operator.
SharePo atorId LICRAT 01036/ Sharing GUI Value Range: 0~5
licy IOSHA TDLOF with
REPOLI D-00103 Commo Unit: None
CY 6 n Actual Value Range: 0~5
LST LOFD-0 Carrier Default Value: None
LICRAT 01037/ RAN
IOSHA TDLOF Sharing
REPOLI D-00103 with
CY 7 Dedicate
MOD LOFD-0 d
LICRAT 70206/ Carrier
IOSHA TDLOF Hybrid
REPOLI D-08122 RAN
CY 4 Sharing
RMV
LICRAT
IOSHA
REPOLI
CY
RatFreq RatType ADD LOFD-0 Camp & Meaning: Indicates the Radio Access Technology
Priority RATFR 0105401 Handov (RAT). This parameter applies only to LTE FDD and
Group EQPRI / er Based LTE TDD.
ORITY TDLOF on SPID GUI Value Range: EUTRAN, UTRAN, GERAN,
GROUP D-00105 Enhance CDMA20001XRTT, CDMA2000HRPD
LST 401 d CS Unit: None
RATFR LOFD-0 Fallback
EQPRI 01090/ Actual Value Range: EUTRAN, UTRAN, GERAN,
to
ORITY TDLOF CDMA20001XRTT, CDMA2000HRPD
CDMA2
GROUP D-00109 000 Default Value: None
MOD 0 1xRTT
RATFR LOFD-0 PS Inter-
EQPRI 01021/ RAT
ORITY TDLOF Mobility
GROUP D-00102 between
RMV 1 E-
RATFR UTRAN
EQPRI and
ORITY CDMA2
GROUP 000
RatFreq DlEarfc ADD LOFD-0 Camp & Meaning: Indicates the downlink frequency. In
Priority n RATFR 0105401 Handov CDMA2000, this parameter indicates the bandclass.
Group EQPRI / er Based Before configuring a priority for a frequency specified
ORITY TDLOF on SPID by this parameter, ensure that an external or local cell
GROUP D-00105 operating on this frequency has been configured. This
LST 401 parameter applies only to LTE FDD and LTE TDD.
RATFR GUI Value Range: 0~68585,229376~229575
EQPRI Unit: None
ORITY
GROUP Actual Value Range: 0~68585,229376~229575
RatFreq Priority ADD LOFD-0 Camp & Meaning: Indicates the priority of the intra-RAT
Priority RATFR 0105401 Handov frequency band or frequency. The value 0 indicates
Group EQPRI / er Based the lowest priority. The value of this parameter must
ORITY TDLOF on SPID be determined together with the priorities of other
GROUP D-00105 RAN frequencies during the network planning. Cell
MOD 401 Sharing reselection priorities in different RATs cannot be the
RATFR LOFD-0 with same. This parameter applies only to LTE FDD and
EQPRI 01036/ Commo LTE TDD.
ORITY TDLOF n GUI Value Range: 0~7
GROUP D-00103 Carrier Unit: None
LST 6 Multi Actual Value Range: 0~7
RATFR LOFD-0 Operator
EQPRI 70210/ s SPID Default Value: 0
ORITY TDLOF Policy
GROUP D-00113
3
RatFreq BandInd ADD LOFD-0 Camp & Meaning: Indicates the GERAN frequency band. This
Priority icator RATFR 0105401 Handov parameter applies only to LTE FDD and LTE TDD.
Group EQPRI / er Based GUI Value Range: GSM_dcs1800, GSM_pcs1900
ORITY TDLOF on SPID
GROUP D-00105 Unit: None
RAN
MOD 401 Sharing Actual Value Range: GSM_dcs1800, GSM_pcs1900
RATFR LOFD-0 with Default Value: GSM_dcs1800
EQPRI 01036/ Commo
ORITY TDLOF n
GROUP D-00103 Carrier
LST 6 Multi
RATFR LOFD-0 Operator
EQPRI 70210/ s SPID
ORITY TDLOF Policy
GROUP D-00113
3
SpidCfg RatFreq ADD LOFD-0 Camp & Meaning: Indicates whether to set the priority for the
PriorityI SPIDCF 0105401 Handov intra-RAT frequency. If this parameter is set to
nd G / er Based CFG(CFG), UEs select the target frequency based on
MOD TDLOF on SPID the priority setting. If this parameter is set to
SPIDCF D-00105 RAN NOT_CFG(NOT_CFG), UEs do not select the target
G 401 Sharing frequency based on the priority setting. This
LOFD-0 with parameter applies only to LTE FDD and LTE TDD.
LST
SPIDCF 01036/ Commo GUI Value Range: NOT_CFG(NOT_CFG),
G TDLOF n CFG(CFG)
D-00103 Carrier Unit: None
6
Actual Value Range: NOT_CFG, CFG
Default Value: NOT_CFG(NOT_CFG)
GeranN LocalCe ADD None None Meaning: Indicates the local cell ID. It uniquely
FGroup llId GERAN identifies a cell within an eNodeB. This parameter
SCellOp NFGRO applies only to LTE FDD and LTE TDD.
UPSCE GUI Value Range: 0~255
LLOP
Unit: None
LST
GERAN Actual Value Range: 0~255
NFGRO Default Value: None
UPSCE
LLOP
MOD
GERAN
NFGRO
UPSCE
LLOP
RMV
GERAN
NFGRO
UPSCE
LLOP
GeranN BcchGr ADD LOFD-0 MOCN Meaning: Indicates the index of the GERAN carrier
FGroup oupId GERAN 01112/ Flexible frequency group. It uniquely identifies a GERAN
SCellOp NFGRO TDLOF Priority carrier frequency group. This parameter applies only
UPSCE D-00111 Based to LTE FDD and LTE TDD.
LLOP 2 Campin GUI Value Range: 0~31
LST g
Unit: None
GERAN
NFGRO Actual Value Range: 0~31
UPSCE Default Value: None
LLOP
MOD
GERAN
NFGRO
UPSCE
LLOP
RMV
GERAN
NFGRO
UPSCE
LLOP
GeranN CnOper ADD LOFD-0 MOCN Meaning: Indicates the ID of the operator. This
FGroup atorID GERAN 01112/ Flexible parameter applies only to LTE FDD and LTE TDD.
SCellOp NFGRO TDLOF Priority GUI Value Range: 0~5
UPSCE D-00111 Based
LLOP 2 Campin Unit: None
GeranN CellRes ADD LOFD-0 MOCN Meaning: Indicates whether to configure a dedicated
FGroup elDediPr GERAN 01112/ Flexible cell-reselection priority based on the PLMN ID of the
SCellOp iCfgInd NFGRO TDLOF Priority local cell for the GERAN carrier frequency group.
UPSCE D-00111 Based This parameter applies only to LTE FDD and LTE
LLOP 2 Campin TDD.
MOD LBFD-0 g GUI Value Range: NOT_CFG(Not configure),
GERAN 0201803 Cell CFG(Configure)
NFGRO / Selectio Unit: None
UPSCE TDLBF n and
LLOP D-00201 Re- Actual Value Range: NOT_CFG, CFG
GeranN CellRes ADD LOFD-0 MOCN Meaning: Indicates the cell reselection dedicated
FGroup elDediPr GERAN 01112/ Flexible priority for a GERAN frequency carrier group based
SCellOp i NFGRO TDLOF Priority on the PLMN ID of the serving cell. The value 0
UPSCE D-00111 Based indicates the lowest priority. If the related SPID
LLOP 2 Campin configuration is specified, set this priority to the one
MOD LBFD-0 g specified in the SPID configuration. If no related
GERAN 0201803 Cell SPID configuration is specified but this parameter is
NFGRO / Selectio set, the eNodeB delivers the cell reselection priorities
UPSCE TDLBF n and of all PLMNs supported by a UE by using the IE
LLOP D-00201 Re- idleModeMobilityControlInfo in an RRC Connection
803 selection Release message to the UE. If no related SPID
LST configuration is specified and this parameter is not set,
GERAN LOFD-0 RAN a UE uses the cell reselection priority of the
NFGRO 01036/ Sharing neighboring GERAN carrier frequency group, which
UPSCE TDLOF with is broadcast in the system information. This parameter
LLOP D-00103 Commo applies only to LTE FDD and LTE TDD.
6 n
Carrier GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0
GeranRa LocalCe ADD None None Meaning: Indicates the cell identity of the local cell. It
nShare llId GERAN uniquely identifies a cell within an eNodeB. This
RANSH parameter applies only to LTE FDD and LTE TDD.
ARE GUI Value Range: 0~255
LST Unit: None
GERAN
RANSH Actual Value Range: 0~255
ARE Default Value: None
MOD
GERAN
RANSH
ARE
RMV
GERAN
RANSH
ARE
GeranRa BcchGr ADD LOFD-0 RAN Meaning: Indicates the index of the GERAN carrier
nShare oupId GERAN 01036/ Sharing frequency group. It uniquely identifies a GERAN
RANSH TDLOF with carrier frequency group. This parameter applies only
ARE D-00103 Commo to LTE FDD and LTE TDD.
LST 6 n GUI Value Range: 0~31
GERAN LOFD-0 Carrier
Unit: None
RANSH 01112/ MOCN
ARE TDLOF Flexible Actual Value Range: 0~31
GeranRa CellRes ADD LOFD-0 RAN Meaning: Indicates whether to configure the cell
nShare elPriorit GERAN 01036/ Sharing reselection priority of the operator that shares the
yCfgInd RANSH TDLOF with neighboring GERAN carrier frequency group. This
ARE D-00103 Commo parameter applies only to LTE FDD and LTE TDD.
MOD 6 n GUI Value Range: NOT_CFG(Not configure),
GERAN LBFD-0 Carrier CFG(Configure)
RANSH 0201803 Cell Unit: None
ARE / Selectio
TDLBF n and Actual Value Range: NOT_CFG, CFG
LST
GERAN D-00201 Re- Default Value: NOT_CFG(Not configure)
RANSH 803 selection
ARE LOFD-0 MOCN
01112/ Flexible
TDLOF Priority
D-00111 Based
2 Campin
LOFD-0 g
70206/ Hybrid
TDLOF RAN
D-08122 Sharing
4
GeranRa CellRes ADD LOFD-0 RAN Meaning: Indicates the cell reselection priority of the
nShare elPriorit GERAN 01036/ Sharing operator that shares the neighboring GERAN carrier
y RANSH TDLOF with frequency group. The value 0 indicates the lowest
ARE D-00103 Commo priority. If the related SPID configuration is specified,
MOD 6 n set this priority to the one specified in the SPID
GERAN LBFD-0 Carrier configuration. If no related SPID configuration is
RANSH 0201803 Cell specified but this parameter is set, the eNodeB
ARE / Selectio delivers the cell reselection priorities of all PLMNs
TDLBF n and supported by a UE by using the IE idleModeMobility-
LST ControlInfo in an RRC Connection Release message
GERAN D-00201 Re-
803 selection to the UE. If no related SPID configuration is
RANSH specified and this parameter is not set, a UE uses the
ARE LOFD-0 MOCN cell reselection priority of the neighboring GERAN
01112/ Flexible carrier frequency group, which is broadcast in the
TDLOF Priority system information. This parameter applies only to
D-00111 Based LTE FDD and LTE TDD.
2 Campin
g GUI Value Range: 0~7
LOFD-0
70206/ Hybrid Unit: None
TDLOF RAN Actual Value Range: 0~7
D-08122 Sharing Default Value: 0
4
UtranNF LocalCe ADD None None Meaning: Indicates the cell ID of the local cell. It
reqSCell llId UTRAN uniquely identifies a cell within an eNodeB. This
Op NFREQ parameter applies only to LTE FDD and LTE TDD.
SCELL GUI Value Range: 0~255
OP
Unit: None
LST
UTRAN Actual Value Range: 0~255
NFREQ Default Value: None
SCELL
OP
MOD
UTRAN
NFREQ
SCELL
OP
RMV
UTRAN
NFREQ
SCELL
OP
UtranNF UtranDl ADD LOFD-0 MOCN Meaning: Indicates the downlink UARFCN of the
reqSCell Arfcn UTRAN 01112/ Flexible neighboring UTRAN frequency. This parameter
Op NFREQ TDLOF Priority applies only to LTE FDD and LTE TDD.
SCELL D-00111 Based GUI Value Range: 0~16383
OP 2 Campin
g Unit: None
LST
UTRAN Actual Value Range: 0~16383
NFREQ Default Value: None
SCELL
OP
MOD
UTRAN
NFREQ
SCELL
OP
RMV
UTRAN
NFREQ
SCELL
OP
UtranNF CnOper ADD LOFD-0 MOCN Meaning: Indicates the ID of the operator. This
reqSCell atorID UTRAN 01112/ Flexible parameter applies only to LTE FDD and LTE TDD.
Op NFREQ TDLOF Priority GUI Value Range: 0~5
SCELL D-00111 Based
OP 2 Campin Unit: None
UtranNF CellRes ADD LOFD-0 MOCN Meaning: Indicates whether to configure a dedicated
reqSCell elDediPr UTRAN 01112/ Flexible cell-reselection priority based on the PLMN ID of the
Op iCfgInd NFREQ TDLOF Priority local cell for the UTRAN frequency. This parameter
SCELL D-00111 Based applies only to LTE FDD and LTE TDD.
OP 2 Campin GUI Value Range: NOT_CFG(Not configure),
MOD LBFD-0 g CFG(Configure)
UTRAN 0201803 Cell Unit: None
NFREQ / Selectio
SCELL TDLBF n and Actual Value Range: NOT_CFG, CFG
OP D-00201 Re- Default Value: NOT_CFG(Not configure)
LST 803 selection
UTRAN LOFD-0 RAN
NFREQ 01036/ Sharing
SCELL TDLOF with
OP D-00103 Commo
6 n
LOFD-0 Carrier
70206/ Hybrid
TDLOF RAN
D-08122 Sharing
4
UtranNF CellRes ADD LOFD-0 MOCN Meaning: Indicates the dedicated cell reselection
reqSCell elDediPr UTRAN 01112/ Flexible priority for a UTRAN frequency based on the PLMN
Op i NFREQ TDLOF Priority ID of the local cell. The value 0 indicates the lowest
SCELL D-00111 Based priority. If the related SPID configuration is specified,
OP 2 Campin set this priority to the one specified in the SPID
MOD LBFD-0 g configuration. If no related SPID configuration is
UTRAN 0201803 Cell specified but this parameter is set, the eNodeB
NFREQ / Selectio delivers the cell reselection priorities of all PLMNs
SCELL TDLBF n and supported by a UE by using the IE idleModeMobility-
OP D-00201 Re- ControlInfo in an RRC Connection Release message
803 selection to the UE. If no related SPID configuration is
LST specified and this parameter is not set, a UE uses the
UTRAN LOFD-0 RAN cell reselection priority of the neighboring UTRAN
NFREQ 01036/ Sharing frequency, which is broadcast in the system
SCELL TDLOF with information. This parameter applies only to LTE FDD
OP D-00103 Commo and LTE TDD.
6 n
Carrier GUI Value Range: 0~7
LOFD-0
70206/ Hybrid Unit: None
TDLOF RAN Actual Value Range: 0~7
D-08122 Sharing Default Value: 0
4
UtranRa LocalCe ADD None None Meaning: Indicates the cell identity of the local cell. It
nShare llId UTRAN uniquely identifies a cell within an eNodeB. This
RANSH parameter applies only to LTE FDD and LTE TDD.
ARE GUI Value Range: 0~255
LST Unit: None
UTRAN
RANSH Actual Value Range: 0~255
ARE Default Value: None
MOD
UTRAN
RANSH
ARE
RMV
UTRAN
RANSH
ARE
UtranRa CellRes ADD LOFD-0 RAN Meaning: Indicates whether to configure the cell
nShare elPriorit UTRAN 01036/ Sharing reselection priority of the operator that shares the
yCfgInd RANSH TDLOF with neighboring UTRAN frequency. This parameter
ARE D-00103 Commo applies only to LTE FDD and LTE TDD.
MOD 6 n GUI Value Range: NOT_CFG(Not configure),
UTRAN LBFD-0 Carrier CFG(Configure)
RANSH 0201803 Cell Unit: None
ARE / Selectio
TDLBF n and Actual Value Range: NOT_CFG, CFG
LST
UTRAN D-00201 Re- Default Value: NOT_CFG(Not configure)
RANSH 803 selection
ARE LOFD-0 MOCN
01112/ Flexible
TDLOF Priority
D-00111 Based
2 Campin
LOFD-0 g
70206/ Hybrid
TDLOF RAN
D-08122 Sharing
4
UtranRa CellRes ADD LOFD-0 RAN Meaning: Indicates the cell reselection priority of the
nShare elPriorit UTRAN 01036/ Sharing operator that shares the neighboring UTRAN
y RANSH TDLOF with frequency. The value 0 indicates the lowest priority. If
ARE D-00103 Commo the related SPID configuration is specified, set this
MOD 6 n priority to the one specified in the SPID configuration.
UTRAN LBFD-0 Carrier If no related SPID configuration is specified but this
RANSH 0201803 Cell parameter is set, the eNodeB delivers the cell
ARE / Selectio reselection priorities of all PLMNs supported by a UE
TDLBF n and by using the IE idleModeMobilityControlInfo in an
LST RRC Connection Release message to the UE. If no
UTRAN D-00201 Re-
803 selection related SPID configuration is specified and this
RANSH parameter is not set, a UE uses the cell reselection
ARE LOFD-0 MOCN priority of the neighboring UTRAN frequency, which
01112/ Flexible is broadcast in the system information. This parameter
TDLOF Priority applies only to LTE FDD and LTE TDD.
D-00111 Based
2 Campin GUI Value Range: 0~7
LOFD-0 g Unit: None
70206/ Hybrid Actual Value Range: 0~7
TDLOF RAN Default Value: 0
D-08122 Sharing
4
EutranN LocalCe ADD None None Meaning: Indicates the ID of the local cell. It uniquely
FreqSCe llId EUTRA identifies a cell within an eNodeB. This parameter
llOp NNFRE applies only to LTE FDD and LTE TDD.
QSCEL GUI Value Range: 0~255
LOP
Unit: None
LST
EUTRA Actual Value Range: 0~255
NNFRE Default Value: None
QSCEL
LOP
MOD
EUTRA
NNFRE
QSCEL
LOP
RMV
EUTRA
NNFRE
QSCEL
LOP
EutranN DlEarfc ADD LOFD-0 MOCN Meaning: Indicates the DL EARFCN of the Operator
FreqSCe n EUTRA 01112/ Flexible Configuration for Serving Cell in EUTRAN
llOp NNFRE TDLOF Priority Frequency. For details, see the 3GPP TS 36.104. This
QSCEL D-00111 Based parameter applies only to LTE FDD and LTE TDD.
LOP 2 Campin GUI Value Range: 0~68585,229376~229575
LST g
Unit: None
EUTRA
NNFRE Actual Value Range: 0~68585,229376~229575
QSCEL Default Value: None
LOP
MOD
EUTRA
NNFRE
QSCEL
LOP
RMV
EUTRA
NNFRE
QSCEL
LOP
EutranN CnOper ADD LOFD-0 MOCN Meaning: Indicates the ID of the operator. This
FreqSCe atorID EUTRA 01112/ Flexible parameter applies only to LTE FDD and LTE TDD.
llOp NNFRE TDLOF Priority GUI Value Range: 0~5
QSCEL D-00111 Based
LOP 2 Campin Unit: None
EutranN CellRes ADD LOFD-0 MOCN Meaning: Indicates whether to configure a dedicated
FreqSCe elDediPr EUTRA 01112/ Flexible cell-reselection priority based on the PLMN ID of the
llOp iCfgInd NNFRE TDLOF Priority local cell for the neighboring E-UTRAN frequency.
QSCEL D-00111 Based This parameter applies only to LTE FDD and LTE
LOP 2 Campin TDD.
MOD LBFD-0 g GUI Value Range: NOT_CFG(Not configure),
EUTRA 0201803 Cell CFG(Configure)
NNFRE / Selectio Unit: None
QSCEL TDLBF n and
LOP D-00201 Re- Actual Value Range: NOT_CFG, CFG
EutranN CellRes ADD LOFD-0 MOCN Meaning: Indicates the cell reselection dedicated
FreqSCe elDediPr EUTRA 01112/ Flexible priority for an E-UTRAN frequency based on the
llOp i NNFRE TDLOF Priority PLMN ID of the local cell. The value 0 indicates the
QSCEL D-00111 Based lowest priority. If the related SPID configuration is
LOP 2 Campin specified, the cell reselection priority specified in the
MOD LBFD-0 g SPID configuration is used. If no related SPID
EUTRA 0201803 Cell configuration is specified but this parameter is set, the
NNFRE / Selectio eNodeB delivers the cell reselection priorities of all
QSCEL TDLBF n and PLMNs supported by a UE by using the IE
LOP D-00201 Re- idleModeMobilityControlInfo in an RRC Connection
803 selection Release message to the UE. If no related SPID
LST configuration is specified and this parameter is not set,
EUTRA LOFD-0 RAN a UE uses the cell reselection priority of the
NNFRE 01036/ Sharing neighboring E-UTRAN frequency, which is broadcast
QSCEL TDLOF with in the system information. This parameter applies only
LOP D-00103 Commo to LTE FDD and LTE TDD.
6 n
Carrier GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
Default Value: 0
EutranN LocalCe ADD None None Meaning: Indicates the ID of the local cell. It uniquely
FreqRan llId EUTRA identifies a cell within an eNodeB. This parameter
Share NNFRE applies only to LTE FDD and LTE TDD.
QRANS GUI Value Range: 0~255
HARE
Unit: None
LST
EUTRA Actual Value Range: 0~255
NNFRE Default Value: None
QRANS
HARE
MOD
EUTRA
NNFRE
QRANS
HARE
RMV
EUTRA
NNFRE
QRANS
HARE
EutranN DlEarfc ADD LOFD-0 RAN Meaning: Indicates the DL EARFCN of the operator
FreqRan n EUTRA 01036/ Sharing that shares the neighboring E-UTRAN frequency. For
Share NNFRE TDLOF with details, see the 3GPP TS 36.104. This parameter
QRANS D-00103 Commo applies only to LTE FDD and LTE TDD.
HARE 6 n GUI Value Range: 0~68585,229376~229575
LST LOFD-0 Carrier
Unit: None
EUTRA 01112/ MOCN
NNFRE TDLOF Flexible Actual Value Range: 0~68585,229376~229575
QRANS D-00111 Priority Default Value: None
HARE 2 Based
MOD LOFD-0 Campin
EUTRA 70206/ g
NNFRE TDLOF Hybrid
QRANS D-08122 RAN
HARE 4 Sharing
RMV
EUTRA
NNFRE
QRANS
HARE
EutranN CellRes ADD LOFD-0 RAN Meaning: Indicates whether to configure the cell
FreqRan elPriorit EUTRA 01036/ Sharing reselection priority. This parameter applies only to
Share yCfgInd NNFRE TDLOF with LTE FDD and LTE TDD.
QRANS D-00103 Commo GUI Value Range: NOT_CFG(Not configure),
HARE 6 n CFG(Configure)
MOD TDLBF Carrier
Unit: None
EUTRA D-00201 Cell
NNFRE 803 Selectio Actual Value Range: NOT_CFG, CFG
QRANS LOFD-0 n and Default Value: NOT_CFG(Not configure)
HARE 01112/ Re-
LST TDLOF selection
EUTRA D-00111 MOCN
NNFRE 2 Flexible
QRANS LOFD-0 Priority
HARE 70206/ Based
TDLOF Campin
D-08122 g
4 Hybrid
RAN
Sharing
EutranN CellRes ADD LOFD-0 RAN Meaning: Indicates the cell reselection priority of the
FreqRan elPriorit EUTRA 01036/ Sharing operator that shares the neighboring E-UTRAN
Share y NNFRE TDLOF with frequency. The value 0 indicates the lowest priority. If
QRANS D-00103 Commo the related SPID configuration is specified, the cell
HARE 6 n reselection priority specified in the SPID
MOD LBFD-0 Carrier configuration is used. If no related SPID configuration
EUTRA 0201803 Cell is specified but this parameter is set, the eNodeB
NNFRE / Selectio delivers the cell reselection priorities of all PLMNs
QRANS TDLBF n and supported by a UE by using the IE idleModeMobility-
HARE D-00201 Re- ControlInfo in an RRC Connection Release message
803 selection to the UE. If no related SPID configuration is
LST specified and this parameter is not set, a UE uses the
EUTRA LOFD-0 MOCN cell reselection priority of the neighboring E-UTRAN
NNFRE 01112/ Flexible frequency, which is broadcast in the system
QRANS TDLOF Priority information. This parameter applies only to LTE FDD
HARE D-00111 Based and LTE TDD.
2 Campin
g GUI Value Range: 0~7
LOFD-0
70206/ Hybrid Unit: None
TDLOF RAN Actual Value Range: 0~7
D-08122 Sharing Default Value: 0
4
Cdma20 LocalCe ADD None None Meaning: Indicates the ID of the local cell. It uniquely
00BcSC llId CDMA2 identifies a cell within an eNodeB. This parameter
ellOp 000BCS applies only to LTE FDD and LTE TDD.
CELLO GUI Value Range: 0~255
P
Unit: None
LST
CDMA2 Actual Value Range: 0~255
000BCS Default Value: None
CELLO
P
MOD
CDMA2
000BCS
CELLO
P
RMV
CDMA2
000BCS
CELLO
P
Cdma20 BandCla ADD LOFD-0 CS Meaning: Indicates the neighboring CDMA2000 band
00BcSC ss CDMA2 01035/ Fallback class. For details, see 3GPP 36.331. This parameter
ellOp 000BCS TDLOF to applies only to LTE FDD and LTE TDD.
CELLO D-00103 CDMA2 GUI Value Range: bc0, bc1, bc2, bc3, bc4, bc5, bc6,
P 5 000 bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15,
LST LOFD-0 1xRTT bc16, bc17, bc18, bc19, bc20, bc21
CDMA2 01021/ PS Inter- Unit: None
000BCS TDLOF RAT
CELLO D-00102 Mobility Actual Value Range: bc0, bc1, bc2, bc3, bc4, bc5, bc6,
P 1 between bc7, bc8, bc9, bc10, bc11, bc12, bc13, bc14, bc15,
E- bc16, bc17, bc18, bc19, bc20, bc21
MOD LOFD-0
CDMA2 01112/ UTRAN Default Value: None
000BCS TDLOF and
CELLO D-00111 CDMA2
P 2 000
RMV MOCN
CDMA2 Flexible
000BCS Priority
CELLO Based
P Campin
g
Cdma20 CnOper ADD LOFD-0 CS Meaning: Indicates the ID of the operator. This
00BcSC atorID CDMA2 01035/ Fallback parameter applies only to LTE FDD and LTE TDD.
ellOp 000BCS TDLOF to GUI Value Range: 0~5
CELLO D-00103 CDMA2
P 5 000 Unit: None
Cdma20 Cdma1 ADD LOFD-0 CS Meaning: Indicates the dedicated cell reselection
00BcSC XrttCell CDMA2 01035/ Fallback priority for a CDMA2000 1xRTT band class based on
ellOp ReselDe 000BCS TDLOF to the PLMN ID of the local cell. The value 0 indicates
diPri CELLO D-00103 CDMA2 the lowest priority. If the related SPID configuration is
P 5 000 specified, set this priority to the one specified in the
MOD TDLBF 1xRTT SPID configuration. If no related SPID configuration
CDMA2 D-00101 S1-flex is specified but this parameter is set, the eNodeB
000BCS 8 delivers the cell reselection priorities of all PLMNs
MOCN supported by a UE by using the IE idleModeMobility-
CELLO TDLOF Flexible
P ControlInfo in an RRC Connection Release message
D-00111 Priority to the UE. If no related SPID configuration is
LST 2 Based specified and this parameter is not set, a UE uses the
CDMA2 LBFD-0 Campin cell reselection priority of the CDMA2000 band class,
000BCS 0201803 g which is broadcast in the system information. This
CELLO / Cell parameter applies only to LTE FDD and LTE TDD.
P TDLBF Selectio GUI Value Range: 0~7
D-00201 n and
803 Re- Unit: None
LOFD-0 selection Actual Value Range: 0~7
01036/ RAN Default Value: 0
TDLOF Sharing
D-00103 with
6 Commo
LOFD-0 n
01112 Carrier
MOCN
Flexible
Priority
Based
Campin
g
Cdma20 HrpdCel ADD LOFD-0 PS Inter- Meaning: Indicates whether to configure a dedicated
00BcSC lReselD CDMA2 01021/ RAT cell-reselection priority for a CDMA2000 HRPD band
ellOp ediPriCf 000BCS TDLOF Mobility class based on the PLMN ID of the local cell. This
gInd CELLO D-00102 between parameter applies only to LTE FDD and LTE TDD.
P 1 E- GUI Value Range: NOT_CFG(Not configure),
MOD LOFD-0 UTRAN CFG(Configure)
CDMA2 01112/ and
CDMA2 Unit: None
000BCS TDLOF
CELLO D-00111 000 Actual Value Range: NOT_CFG, CFG
P 2 MOCN Default Value: NOT_CFG(Not configure)
LST LOFD-0 Flexible
CDMA2 01036/ Priority
000BCS TDLOF Based
CELLO D-00103 Campin
P 6 g
RAN
Sharing
with
Commo
n
Carrier
Cdma20 HrpdCel ADD LOFD-0 PS Inter- Meaning: Indicates the dedicated cell reselection
00BcSC lReselD CDMA2 01021/ RAT priority for a CDMA2000 HRPD band class based on
ellOp ediPri 000BCS TDLOF Mobility the PLMN ID of the local cell. The value 0 indicates
CELLO D-00102 between the lowest priority. If the related SPID configuration is
P 1 E- specified, set this priority to the one specified in the
MOD LOFD-0 UTRAN SPID configuration. If no related SPID configuration
CDMA2 01112/ and is specified but this parameter is set, the eNodeB
000BCS TDLOF CDMA2 delivers the cell reselection priorities of all PLMNs
CELLO D-00111 000 supported by a UE by using the IE idleModeMobility-
P 2 MOCN ControlInfo in an RRC Connection Release message
Flexible to the UE. If no related SPID configuration is
LST LBFD-0 specified and this parameter is not set, a UE uses the
CDMA2 0201803 Priority
Based cell reselection priority of the CDMA2000 band class,
000BCS / which is broadcast in the system information. This
CELLO TDLBF Campin
g parameter applies only to LTE FDD and LTE TDD.
P D-00201
803 Cell GUI Value Range: 0~7
LOFD-0 Selectio Unit: None
01036/ n and Actual Value Range: 0~7
TDLOF Re-
selection Default Value: 0
D-00103
6 RAN
Sharing
with
Commo
n
Carrier
License UserNu ADD TDLBF License Meaning: Indicates the proportion of users that the
Sharing mSharin LICENS D-00401 Manage operator can share with other operators when the
Policy gRate ESHAR 4 ment eNodeB is shared among operators. This parameter
INGPO LOFD-0 RAN must be set based on the contract signed with
LICY 01036/ Sharing operators. This parameter applies only to LTE FDD.
MOD TDLOF with GUI Value Range: 0~100
LICENS D-00103 Commo Unit: %
ESHAR 6 n
INGPO Carrier Actual Value Range: 0~100
LOFD-0
LICY 01037/ RAN Default Value: 0
LST TDLOF Sharing
LICENS D-00103 with
ESHAR 7 Dedicate
INGPO LOFD-0 d
LICY 70206 Carrier
LOFD-0 Hybrid
70213 RAN
Sharing
Fair
User
Sharing
CnOpSh Primary ADD LOFD-0 Hybrid Meaning: Indicates the ID of the primary operator in a
aringGr Operator CNOPS 70206/ RAN carrier-sharing operator group.
oup Id HARIN TDLOF Sharing GUI Value Range: 0~5
GGROU D-08122
P 4 Unit: None
CnOpSh Seconda LST LOFD-0 Hybrid Meaning: Indicates the list of secondary operators in a
aringGr ryOperat CNOPS 70206/ RAN carrier-sharing operator group.
oup orList HARIN TDLOF Sharing GUI Value Range: 0~5
GGROU D-08122
P 4 Unit: None
Cell CnOpSh ADD LOFD-0 Hybrid Meaning: Indicates the ID of the eNodeB operator
aringGr CELL 70206/ RAN group that shares the cell. This parameter must be set
oupId MOD TDLOF Sharing to a value within the range of 0 to 5 if the eNodeB
CELL D-08122 works in hybrid RAN sharing mode. This parameter
4 must be set to 255 (an invalid value) in independent
LST RAN sharing, RAN sharing with dedicated carrier, or
CELL RAN sharing with common carrier mode.
GUI Value Range: 0~5,255
Unit: None
Actual Value Range: 0~5,255
Default Value: 255
Cell LocalCe ACT None None Meaning: Indicates the local ID of the cell. It uniquely
llId CELL identifies a cell within a BS.
ADD GUI Value Range: 0~255
CELL Unit: None
ADD Actual Value Range: 0~255
CELLB
Default Value: None
AND
BLK
CELL
DEA
CELL
DSP
CELL
DSP
CELLC
ALIBR
ATION
DSP
CELLC
AMCST
ATUS
DSP
CELLH
LHCHK
DSP
CELLL
AA
DSP
CELLP
HYTOP
O
DSP
CELLU
LCOMP
CLUST
ER
DSP
CELLU
LICCL
USTER
DSP
DDCEL
LGROU
P
DSP
LIOPTR
ULE
DSP
PRIBBP
ADJUS
T
LST
CELL
LST
CELLB
AND
MOD
CELL
RMV
CELL
RMV
CELLB
AND
RMV
CELLN
RT
RST
EUCEL
LRES
STR
CELLH
LHCHK
STR
CELLR
FLOOP
BACK
STR
CELLS
ELFTES
T
STR
LRTWP
RTTST
STR
PRIBBP
ADJUS
T
UBL
CELL
DSP
CELLB
YLOCA
TION
DSP
LRTWP
RTTST
DSP
PRIBBP
RESINF
O
S1Interf S1Interf ADD LBFD-0 Star Meaning: Indicates the S1 interface ID. If the S1
ace aceId S1INTE 0300101 Topolog interface is set up based on the endpoint configuration
RFACE / y mode, the value range is 40000 to 65534. If the S1
BLK TDLBF Chain interface is set up based on the link configuration
S1INTE D-00300 Topolog mode using the CME or MML commands, the
RFACE 101 y recommended value range is 0 to 39999.
DSP LBFD-0 Tree GUI Value Range: 0~65534
S1INTE 0300102 Topolog Unit: None
RFACE / y
TDLBF Actual Value Range: 0~65534
MOD D-00300 S1-flex Default Value: None
S1INTE 102
RFACE
LBFD-0
RMV 0300103
S1INTE /
RFACE TDLBF
RST D-00300
S1INTE 103
RFACE LBFD-0
UBL 01018/
S1INTE TDLBF
RFACE D-00101
8
X2Interf X2Interf ADD LBFD-0 Star Meaning: Indicates the X2 interface ID. If the X2
ace aceId X2INTE 0300101 Topolog interface is set up based on the end point configuration
RFACE / y mode, the value range is 40000 to 65535. If the X2
DSP TDLBF Chain interface is set up based on the link configuration
X2INTE D-00300 Topolog mode using the CME or MML commands, the
RFACE 101 y recommended value range is 0 to 39999.
DSP LBFD-0 Tree GUI Value Range: 0~65535
X2UPIN 0300102 Topolog Unit: None
FO / y
TDLBF Actual Value Range: 0~65535
MOD D-00300 Default Value: None
X2INTE 102
RFACE
LBFD-0
RMV 0300103
X2INTE /
RFACE TDLBF
RST D-00300
X2INTE 103
RFACE
CellRes CellRes MOD LBFD-0 Cell Meaning: Indicates the cell reselection priority of the
el elPriorit CELLR 0201803 Selectio serving frequency. The value 0 indicates the lowest
y ESEL / n and priority. The value of this parameter must be
LST TDLBF Re- determined together with the priorities of other
CELLR D-00201 selection frequencies during the network planning. Frequencies
ESEL 803 Broadca used for different RATs must be assigned different cell
LBFD-0 st of reselection priorities. This parameter applies only to
02009/ system LTE FDD and LTE TDD.
TDLBF informat GUI Value Range: 0~7
D-00200 ion Unit: None
9 PS Inter- Actual Value Range: 0~7
LOFD-0 RAT
01021/ Mobility Default Value: 7
TDLOF between
D-00102 E-
1 UTRAN
LOFD-0 and
01111 CDMA2
000
LOFD-0
01112/ PS
TDLOF Mobility
D-00111 from E-
2 UTRAN
to
CDMA2
000
HRPD
Based
on
Frequen
cy-
specific
Factors
MOCN
Flexible
Priority
Based
Campin
g
LBFD-0 Mobility and blind handovers can be triggered only if these two
02018/ Manage options are selected. This option applies only to LTE
TDLBF ment FDD and LTE TDD.
D-00201 NSA GUI Value Range: BlindHoSwitch(BlindHoSwitch),
8 Network UtranPsHoSwitch(UtranPsHoSwitch),
MRFD- ing UtranSrvccSwitch(UtranSrvccSwitch),
131122 based on GeranSrvccSwitch(GeranSrvccSwitch),
MRFD- EPC(LT UtranRedirectSwitch(UtranRedirectSwitch),
131132 E FDD) GeranRedirectSwitch(GeranRedirectSwitch),
NSA UFCsfbBlindHoDisSwitch(UFCsfbBlindHoDisS-
Network witch), HighSpeedCsfbBlind-
ing Switch(HighSpeedCsfbBlindSwitch)
based on Unit: None
EPC(LT Actual Value Range: BlindHoSwitch,
E TDD) UtranPsHoSwitch, UtranSrvccSwitch,
GeranSrvccSwitch, UtranRedirectSwitch,
GeranRedirectSwitch, UFCsfbBlindHoDisSwitch,
HighSpeedCsfbBlindSwitch
Default Value: BlindHoSwitch:Off,
UtranPsHoSwitch:Off, UtranSrvccSwitch:Off,
GeranSrvccSwitch:Off, UtranRedirectSwitch:Off,
GeranRedirectSwitch:Off, UFCsfbBlindHoDisS-
witch:Off, HighSpeedCsfbBlindSwitch:Off
HoSwitch:Off, CdmaHrpdOptimisedHoSwitch:Off,
GeranNaccSwitch:Off, GeranCcoSwitch:Off,
Cdma1xRttSrvccSwitch:Off, CdmaHrpdRedirectS-
witch:Off, Cdma1xRttRedirectSwitch:Off,
BlindHoSwitch:Off, LcsSrvccSwitch:Off,
AutoGapSwitch:Off, UeVoipOnHspaCapSwitch:Off,
UtranFddB1CapSwitch:Off, CdmaHrpdNonOptMea-
HoSwitch:Off
CellRes LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
elGeran llId CELLR identifies a cell within an eNodeB. This parameter
ESELG applies only to LTE FDD and LTE TDD.
ERAN GUI Value Range: 0~255
LST Unit: None
CELLR
ESELG Actual Value Range: 0~255
ERAN Default Value: None
MOD
CELLR
ESELG
ERAN
RMV
CELLR
ESELG
ERAN
CellRes TReselG ADD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
elGeran eran CELLR 0201803 Selectio determine whether to reselect a neighboring GERAN
ESELG / n and cell to camp on. During the evaluation period, if the
ERAN TDLBF Re- signal quality in a neighboring GERAN cell is better
MOD D-00201 selection than that in the serving cell and a UE camps on the
CELLR 803 Broadca serving cell for more than 1s, the UE attempts to
ESELG LBFD-0 st of reselect the neighboring GERAN cell to camp on.
ERAN 02009/ system This parameter applies only to LTE FDD and LTE
TDLBF informat TDD.
LST
CELLR D-00200 ion GUI Value Range: 0~7
ESELG 9 MOCN Unit: s
ERAN LOFD-0 Flexible Actual Value Range: 0~7
01112/ Priority
TDLOF Based Default Value: 1
D-00111 Campin
2 g
CellRes LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
elUtran llId CELLR identifies a cell within an eNodeB. This parameter
ESELU applies only to LTE FDD and LTE TDD.
TRAN GUI Value Range: 0~255
LST Unit: None
CELLR
ESELU Actual Value Range: 0~255
TRAN Default Value: None
MOD
CELLR
ESELU
TRAN
RMV
CELLR
ESELU
TRAN
CellRes TReselU ADD LBFD-0 Broadca Meaning: Indicates the evaluation period for a UE to
elUtran tran CELLR 02009/ st of determine whether to reselect a neighboring UTRAN
ESELU TDLBF system cell to camp on. During the evaluation period, if the
TRAN D-00200 informat signal quality in a neighboring UTRAN cell is better
MOD 9 ion than that in the serving cell and a UE camps on the
CELLR LBFD-0 Cell serving cell for more than 1s, the UE attempts to
ESELU 0201803 Selectio reselect the neighboring UTRAN cell to camp on.
TRAN / n and This parameter applies only to LTE FDD and LTE
TDLBF Re- TDD.
LST
CELLR D-00201 selection GUI Value Range: 0~7
ESELU 803 MOCN Unit: s
TRAN LOFD-0 Flexible Actual Value Range: 0~7
01112/ Priority
TDLOF Based Default Value: 1
D-00111 Campin
2 g
CellRes LocalCe LST None None Meaning: Indicates the local ID of the cell. It uniquely
el llId CELLR identifies a cell within a BS.
ESEL GUI Value Range: 0~255
MOD Unit: None
CELLR
ESEL Actual Value Range: 0~255
Default Value: None
CellRes TReselE MOD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
el utran CELLR 0201803 Selectio determine whether to perform cell reselections to a
ESEL / n and new E-UTRAN cell. If the signal quality of a new E-
LST TDLBF Re- UTRAN cell is better than that of the serving cell
CELLR D-00201 selection within the period specified by this parameter and a UE
ESEL 803 Broadca camps on the serving cell for more than 1s, the UE
LBFD-0 st of initiates cell reselections to the new E-UTRAN cell.
02009/ system This parameter applies only to LTE FDD and LTE
TDLBF informat TDD.
D-00200 ion GUI Value Range: 0~7
9 MOCN Unit: s
LOFD-0 Flexible Actual Value Range: 0~7
01112/ Priority
TDLOF Based Default Value: 1
D-00111 Campin
2 g
CellRes LocalCe ADD None None Meaning: Indicates the local ID of the cell. It uniquely
elCdma llId CELLR identifies a cell within an eNodeB. This parameter
2000 ESELC applies only to LTE FDD and LTE TDD.
DMA20 GUI Value Range: 0~255
00
Unit: None
LST
CELLR Actual Value Range: 0~255
ESELC Default Value: None
DMA20
00
MOD
CELLR
ESELC
DMA20
00
RMV
CELLR
ESELC
DMA20
00
CellRes Treselec ADD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
elCdma tionHrp CELLR 0201803 Selectio determine whether to reselect a neighboring
2000 d ESELC / n and CDMA2000 HRPD cell to camp on. During the
DMA20 TDLBF Re- evaluation period, if the signal quality in a
00 D-00201 selection neighboring CDMA2000 HRPD cell is better than that
MOD 803 PS Inter- in the serving cell and a UE camps on the serving cell
CELLR LOFD-0 RAT for more than 1s, the UE attempts to reselect the
ESELC 01021/ Mobility neighboring CDMA2000 HRPD cell to camp on. For
DMA20 TDLOF between details about this parameter, see 3GPP TS 36.331.
00 D-00102 E- This parameter applies only to LTE FDD and LTE
1 UTRAN TDD.
LST
CELLR LBFD-0 and GUI Value Range: 0~7
ESELC 02009/ CDMA2 Unit: s
DMA20 TDLBF 000
Actual Value Range: 0~7
00 D-00200 Broadca
9 st of Default Value: 1
LOFD-0 system
01112/ informat
TDLOF ion
D-00111 MOCN
2 Flexible
Priority
Based
Campin
g
CellRes Cdma1 ADD LBFD-0 Cell Meaning: Indicates the evaluation period for a UE to
elCdma XrttTres CELLR 0201803 Selectio determine whether to reselect a neighboring
2000 election ESELC / n and CDMA2000 1xRTT cell to camp on. During the
DMA20 TDLBF Re- evaluation period, if the signal quality in a
00 D-00201 selection neighboring CDMA2000 1xRTT cell is better than
MOD 803 CS that in the serving cell and a UE camps on the serving
CELLR LOFD-0 Fallback cell for more than 1s, the UE attempts to reselect the
ESELC 01035/ to neighboring CDMA2000 1xRTT cell to camp on. For
DMA20 TDLOF CDMA2 details about this parameter, see 3GPP TS 36.331.
00 D-00103 000 This parameter applies only to LTE FDD and LTE
5 1xRTT TDD.
LST
CELLR LBFD-0 Broadca GUI Value Range: 0~7
ESELC 02009/ st of Unit: s
DMA20 TDLBF system Actual Value Range: 0~7
00 D-00200 informat
9 ion Default Value: 1
TDLOF Enhance
D-00109 d CS
0/ Fallback
LOFD-0 to
01090 CDMA2
LOFD-0 000
01112/ 1xRTT
TDLOF MOCN
D-00111 Flexible
2 Priority
Based
Campin
g
CnOper CnOper ADD LOFD-0 Multi Meaning: This parameter indicates the ID of the
atorSpid atorId CNOPE 70210/ Operator operator. This parameter applies only to LTE FDD and
Cfg RATOR TDLOF s SPID LTE TDD.
SPIDCF D-00113 Policy GUI Value Range: 0~5
G 3
Unit: None
LST
CNOPE Actual Value Range: 0~5
RATOR Default Value: None
SPIDCF
G
MOD
CNOPE
RATOR
SPIDCF
G
RMV
CNOPE
RATOR
SPIDCF
G
CnOper Spid ADD LOFD-0 Intra- Meaning: Indicates the dedicated SPID for an
atorSpid CNOPE 01032/ LTE operator. According to 3GPP specifications, the SPID
Cfg RATOR TDLOF Load can be from 1 to 256. When this parameter is set to 0,
SPIDCF D-00103 Balancin the eNodeB does not obtain the SPID from the MME
G 2 g or the eNodeB is not configured with an SPID for
LST LOFD-0 Inter- UEs. This parameter applies only to LTE FDD and
CNOPE 01044/ RAT LTE TDD.
RATOR TDLOF Load GUI Value Range: 0~256
SPIDCF D-00104 Sharing Unit: None
G 4 to
UTRAN Actual Value Range: 0~256
MOD LOFD-0
CNOPE 01045/ Inter- Default Value: None
RATOR TDLOF RAT
SPIDCF D-00104 Load
G 5 Sharing
RMV LOFD-0 to
CNOPE 01054/ GERAN
RATOR TDLOF Flexible
SPIDCF D-00105 User
G 4 Steering
LOFD-0 Camp &
0105401 Handov
/ er Based
TDLOF on SPID
D-00105 UL Pre-
401 allocatio
LOFD-0 n Based
01059/ on SPID
TDLOF Multi
D-00105 Operator
9 s SPID
LOFD-0 Policy
70210/
TDLOF
D-00113
3
CnOper RatFreq ADD LOFD-0 Intra- Meaning: Indicates whether to set a RAT/frequency
atorSpid PriorityI CNOPE 01032/ LTE priority. If this parameter is set to CFG, UEs
Cfg nd RATOR TDLOF Load preferentially camp on the RAT or frequency. If this
SPIDCF D-00103 Balancin parameter is set to NOT_CFG, UEs do not
G 2 g preferentially camp on the RAT or frequency. This
MOD LOFD-0 Inter- parameter applies only to LTE FDD and LTE TDD.
CNOPE 01044/ RAT GUI Value Range: NOT_CFG(NOT_CFG),
RATOR TDLOF Load CFG(CFG)
SPIDCF D-00104 Sharing Unit: None
G 4 to
UTRAN Actual Value Range: NOT_CFG, CFG
LST LOFD-0
CNOPE 01045/ Inter- Default Value: NOT_CFG(NOT_CFG)
RATOR TDLOF RAT
SPIDCF D-00104 Load
G 5 Sharing
LOFD-0 to
70210/ GERAN
TDLOF Multi
D-00113 Operator
3 s SPID
Policy
CnOper RatFreq ADD LOFD-0 Intra- Meaning: Indicates the ID of a RAT/frequency priority
atorSpid Priority CNOPE 01032/ LTE group. This parameter applies only to LTE FDD and
Cfg GroupId RATOR TDLOF Load LTE TDD.
SPIDCF D-00103 Balancin GUI Value Range: 0~255
G 2 g
Unit: None
MOD LOFD-0 Inter-
CNOPE 01044/ RAT Actual Value Range: 0~255
RATOR TDLOF Load Default Value: 0
SPIDCF D-00104 Sharing
G 4 to
LST LOFD-0 UTRAN
CNOPE 01045/ Inter-
RATOR TDLOF RAT
SPIDCF D-00104 Load
G 5 Sharing
LOFD-0 to
01054/ GERAN
TDLOF Flexible
D-00105 User
4 Steering
LOFD-0 Camp &
0105401 Handov
/ er Based
TDLOF on SPID
D-00105 UL Pre-
401 allocatio
LOFD-0 n Based
01059/ on SPID
TDLOF Multi
D-00105 Operator
9 s SPID
LOFD-0 Policy
70210/
TDLOF
D-00113
3
13 Counters
14 Glossary
15 Reference Documents