Professional Documents
Culture Documents
VORTEX VRN-200.manual.250412
VORTEX VRN-200.manual.250412
ROTATOR
MODEL: VRN-200, VRN-210
VRN-360, VRN-480
USER’S MANUAL
OPERATION / MAINTENANCE
SERVICE and PARTS LIST
Safety Information
Your GEMMY SHAKER has been designed with functions, reliability and
safety in mind. This manual contains important operation and safety
information, the user must carefully read and understand the content of this
manual prior to installing this equipment in conformance with your local
electrical codes.
Safety Information
Your GEMMY SHAKER has been designed with functions, reliability and
safety in mind. This manual contains important operation and safety
information, the user must carefully read and understand the content of this
manual prior to installing this equipment in conformance with your local
electrical codes.
Standard:
This equipment complies with EC Electromagnetic Compatibility
requirement of EN60601-1-2. EMI filter is designed in conformity with
89/336 EEC-EMC Directive.
ISO9001 + 13485
FDA listed (USA) and GMP (Good Manufacturing Practice)
Specification
(mm)
Speed range 10 – 400 rpm 75 – 250 rpm 75 – 250 rpm 75 x 250 rpm
diameter
Motor Brush-less motor DC24V, Gear motor DC24V, gear motor DC24V, gear motor
1
Intended use
To provide a desired gentle rotation to vigorous agitation for mixing test
solutions in micro-titration assays and for use in hematology, urology, or
EIA/ELISA immunology within the range of 10 – 400 rpm (VRN-480) for
mixing each test tube or well, flask evenly by the orbiting motion.
Installation
Remove the equipment carefully from the packing material, check the
electrical specifications located on side of the equipment. Plug cord into a
properly grounded outlet.
WARNING:
Do not lift the equipment by pulling the platform out of the packing materials,
there is possibility of damage to the equipment.
Contents
Optional accessory
OPERATION:
4、 VRN-480:
When flasks are used for operation, choice of various sizes of stainless
steel clamps (holders) for flasks to meet your requirement. Just turn the
screwdriver to fasten the clamps into the platform properly. Fasteners
are attached. It does not need to remove the platform for screwing the
flasks holders
1、VRN-480:
Set time to your desired time for intermittent operation, or set time to
HOLD position for the continuous operation.
7、 Set speed by turning the control knob clockwise to your desired speed.
The platform starts to rotate. VRN-480 and VRN-360 are equipped
with the tachometer, read the speed directly from the tachometer.
No speed indicator is mounted for VRN-210 and VRN-200, user is
requested to use the digital speed meter to set and monitor rotating
speed.
4
How to calibrate the FIXED speed:
The recalibration of fixed speed is applied to VRN-200, 210, 360 only.
3、 The drive motor and linkage assembly does not required lubrication.
6、 GEMMY will not assure any responsibility on persons who violate the
regulations established above.
7、 In case of the spilt solution or specimen from the flasks or vessels,
disconnect from the power supply immediately to avoid the electrical
shock. Disassemble the equipment and use cloth to clean the solution
then dry the equipment by air. Heating dry is prohibited.
8、 When the rubber-form pad is polluted by the spilt solution, remove the
pad from the equipment and wearing latex gloves to wash the rubber-
form pad. Dry the pad naturally by air. Heat dry is prohibited.
Take care of the water treatment after cleaning.
10、 Once the rotating pivot is movable, adjust and position the pivot
properly, rotate the platform until the rotating drive is smoothly, then
glue it firmly.
5
Disassembly
Troubleshooting :
6
Direction to clean:
Transportation
- Fragile, Handle With Care
- Do not drop the equipment
- Do not place this equipment upside down
- Do not move the equipment by pulling its platform
Storage
- Do not place this equipment in draft, sunlight or near a piece of equipment,
which emits heat as well as electromagnetic conduction emission.
- Disconnect power supply when store this equipment
- Do not place or store equipment where it can fall down easily
- This equipment shall be stored under the condition of room temperature.
7
Diagram of Components
VRN-480
PARTS LIST
11 Motor 1
No Description Qty 12 Tachometer 1
13 Speed regulator, VR 1
1 Platform 1 14 Timer, mechanical 1
2 Base, ball bearings (Upper) 1 15 ON/OFF switch 1
16 Control knob, timer 1
3 Eccentric 3 17 Control knob, VR 1
4 Base, ball bearings (Lower) 1 18 Electrical outlet 1
19 Sealed ball bearings 6
5 Circuit board, RPM 1
6 Case 1
7 Pulley wheel (Large) 1
8 Pulley belt 1
9 Pulley wheel (Small) 1
10 Feet 4
8
Diagram of Components
VRN-200, 210, 360
PARTS LIST:
No Description Qty
1 Rubber foam pad 1 13 Rubber support 4
2 Platform 1 14 Speed regulator, VR 1
3 Rotation pivot 4 15 Power cord 1
4 Aluminum rack 1 16 Control knob, speed regulator 1
5 Ball bearing 1 17 Housing 1
6 Eccentric 4 18 Feet 4
7 Base, ball bearing 1 19 Control knob, timer 1
8 Base, rotation pivot 4 20 ON/OFF switch 1
9 Plate, eccentric & pivot 1 21 Switch, fixed speed 1
10 Circuit board 1 22 Timer, 60 minutes 1
11 Motor, gear motor, DC 24V 1 23 Tachometer, VRN-360 1
12 Transformer 1 24 Housing, VRN-360 1
9
Wiring Diagram
VRN-480
1 2 3 4 5 6
○ ○
Fuse
○ ○
○
□
○ □
Timer □
RPM
○ ○ ○ ○
SW
○ ○
Speed Detector
9 8 7 6 5 4 3 2 1
○ ○
R11
○-vvvvvvvv-○
R10 Motor
○-vvvvvvvv-○
A
SVR204 B
○ A: Lines: # 3 Blue B:# 1 Yellow
# 6 Red # 2 Yellow
○-vvwvvwvv−○ # 5 White
VR20K
RPM Sensor
Electronic Parts:
Capacitor: 115V 6UF250V
220V1.5UF350V
10
Wiring diagram:
OFF Transformer ○A
○ OV ○C
○ ○ 110V 24V ○B
○ ○ 220V ○V
AC Timer ON ▌▌ P.C.B.
○ ○R
○ ○T
○ ○+
Fixed ▌ ○-
11
One Year Limited Warranty
Company name :
Address :
Phone No. :
Fax No. :
Email address :
Date of purchase:
Product model :
Serial No. :
Distributor :