Professional Documents
Culture Documents
2004 Peugeot 307 SW PDF
2004 Peugeot 307 SW PDF
15-03-2004
3
YOUR 307 SW AT A GLANCE
20 - 12 V accessories socket.
7 - Electronic stability control
(ESP/ASR) button. 34 - Fuse box.
21 - Can holder.
15-03-2004
5
YOUR 307 SW AT A GLANCE
FRONT SEATS
1 - Forwards/backwards adjust-
ment.
2 - Seat back angle adjustment.
3 - Driver or passenger seat
height adjustment.
4 - Front removable armrest.
5 - Head restraint height and
angle adjustment.
To raise or lower the head re-
straint, pull it forwards, sliding
it at the same time.
6 - Storage drawer.
7 - "Aircraft" style table.
80
15-03-2004
7
YOUR 307 SW AT A GLANCE
REAR SEATS
Moving a side seat: Moving the centre seat: Moving an additional seat:
- forwards/backwards adjust- - forwards/backwards adjustment - seat back angle adjustment (1),
ment (1), (1), - head restraint height adjust-
- seat back angle adjustment (2), - seat back angle adjustment, ment (2),
- head restraint height adjust- table position (2), - folding down (3),
ment (3), - head restraint height adjust- - removal, reitting (4).
- folding down (4), ment (3),
- removal, reitting (5). - folding down (4),
- removal, reitting (5).
82
15-03-2004
8
YOUR 307 SW AT A GLANCE
92
15-03-2004
9
YOUR 307 SW AT A GLANCE
BOOT FITTINGS
118
15-03-2004
10
YOUR 307 SW AT A GLANCE
REAR PARKING
ASSISTANCE
This system, located in the rear
bumper, detects any obstacle
(person, vehicle, tree, gate...) be-
FILLING WITH FUEL Inside the vehicle: Push the hind the vehicle.
handle on the left hand side, un- Activation
This operation must be carried out der the fascia.
with the engine switched off. With the engine running, the
A label on the inside of the lap system is activated as soon as
shows which type of fuel to use. reverse gear is engaged; a bleep
shows that it is active.
The capacity of the tank is ap-
proximately 13 gallons (60 litres). Proximity information is given by
an audible signal, consisting of
When you ill your tank, do not bleeps which become more rapid
continue after the third cut-off as the vehicle approaches the
of the pump, to avoid a possible obstacle.
malfunction.
When the distance between the
Low fuel level warning light rear of the vehicle and the obsta-
From the time this light comes on, cle is less than thirty centimetres,
the range remaining is approxi- the signal becomes continuous.
mately 30 miles (50 km). In neutral, the system be-
comes inactive.
Outside the vehicle: Lift
the catch, raise the bon-
net and secure the strut to
keep the bonnet open. 130
103 103
15-03-2004
13
YOUR 307 SW AT A GLANCE
AIR CONDITIONING
N° Symbol Function
Temperature
3 adjustment.
Air conditioning
6 control.
76
15-03-2004
15
YOUR 307 SW AT A GLANCE
Air conditioning
4 control.
6 Switching off.
Temperature
7 adjustment.
Automatic comfort
8 programme.
Automatic visibility
9
78 programme.
15-03-2004
18
INSTRUMENTS AND CONTROLS
19 - Rear fog lamp indicator light.
20 - Electronic stability control (ESP/
ASR) warning light.
21 - Front fog lamps indicator light.
22 - Diesel engine preheating light.
23 - Main beam headlamps indicator
light.
24 - Low coolant level warning light
(Diesel).
25 - Dipped beam headlamps
indicator light.
26 - Water in diesel ilter warning
light (Diesel).
27 - Lighting rheostat.
15-03-2004
19
INSTRUMENTS AND CONTROLS
18 - Trip recorder zero reset.
19 - Rear fog lamp indicator light.
20 - Electronic stability control
(ESP/ASR) warning light.
21 - Front fog lamps indicator light.
22 - Main beam headlamps indicator
light.
23 - Dipped beam headlamps
indicator light.
24 - Lighting rheostat.
25 - Sport programme indicator light.
26 - Snow programme indicator light.
27 - Gear lever position indicator.
15-03-2004
20
INSTRUMENTS AND CONTROLS
INSTRUMENTS AND Engine oil pressure To prevent the risk of scalding, un-
CONTROLS warning light screw the cap by two turns to allow
the pressure to drop.
A permanently lit warning light or Linked to the central STOP Once the pressure has dropped, re-
one that lashes with the engine warning light. move the cap and top up the level.
running, indicates an operating If it comes on with the engine run-
fault in the relevant unit. Some Contact a PEUGEOT dealer.
ning, it is accompanied by an au-
warning lights may be linked to dible signal and the message ''Oil
buzzers and a message on the mul- pressure insuficient'' or ''Top up
ti-function display. Do not ignore engine oil level'' on the multi-func-
this warning: contact a PEUGEOT tion display.
dealer as soon as possible. Stop immediately.
If the Central STOP warning light Handbrake and low
If there is a lack of oil in the lubrica- brake fluid level
comes on when you are driving, tion circuit, top up the level.
stop immediately where it is safe warning light
to do so. Contact a PEUGEOT dealer without
delay.
Linked to the central STOP warning
light.
This comes on each time the ignition
is switched on.
Illumination of this light is accompa-
Central STOP Diesel engine low nied by an audible signal and a mes-
warning light coolant level warning sage on the multi-function display
light indicating the cause of the warning:
This light comes on
each time the ignition is - ''Handbrake on'', if the handbrake
switched on. Linked to the central STOP warning is applied or has not been released
light. correctly,
It is linked to the "engine oil pres-
sure", ''coolant level low'', ''brake luid This comes on for approximately 3 sec- - ''Brake luid level low'' if there is
level'', "electronic brake force distri- onds each time the ignition is switched an excessive drop in the brake luid
bution fault" warning lights and the on. (if the light remains on even with
coolant temperature gauge. the handbrake released),
This warning light is accompanied by
Stop immediately if it lashes with an audible signal and the message - ''Braking fault'' is displayed si-
the engine running. "Top up engine coolant level" on multaneously with the ABS light,
Contact a PEUGEOT dealer. the multi-function display. indicating a malfunction of the
electronic brake force distribution.
Stop immediately.
Stop immediately.
Warning: Allow the engine to cool
before topping up. Contact a PEUGEOT dealer.
The cooling system is pressurised.
15-03-2004
21
INSTRUMENTS AND CONTROLS
Battery charge warning Electronic stability To regenerate the ilter, you are
light programme (ESP/ASR) advised to drive, as soon as pos-
warning light sible when trafic conditions permit,
This comes on each time the at a speed of 35 mph (60 km/h) or
ignition is switched on. This comes on for 3 seconds above for at least ive minutes (until
If it comes on with the engine run- each time the ignition is switched the warning light goes out). If the
ning, it is accompanied by an audi- on. warning light remains on, contact a
ble signal and a message "Battery If the light remains on or comes on PEUGEOT dealer.
charge fault" on the multi-function when the engine is running and the Note: following prolonged operation
display. vehicle is moving, it is accompa- of the vehicle at very low speed or at
It can indicate: nied by an audible signal and the idle, you may, in exceptional circum-
- faulty operation of the charging cir- message ''ESP/ASR system not stances, notice emissions of water
cuit, functioning'' on the multi-function vapour at the exhaust on accelera-
display; contact a PEUGEOT dealer. tion. This does not have any effect
- loose battery or starter terminals,
When the engine is running and the on the vehicle's performance or on
- a cut or slack alternator belt, vehicle is moving, it lashes if the the environment.
- an alternator fault. system is activated. If it lashes when the engine is run-
Contact a PEUGEOT dealer. It is lit continuously when the system ning, accompanied by an audible
is disarmed. signal and the message ''Catalytic
converter fault'' on the multi-func-
tion display, it indicates a malfunction
in the injection or ignition system.
Anti-lock braking There is a risk of damage to the cata-
Engine diagnostics lytic converter (petrol engines only).
system (ABS) warning warning light Contact a PEUGEOT dealer as soon
light This comes on each time the as possible.
This light comes on for 3 sec- ignition is switched on.
onds each time the ignition is switched If it comes on with the engine run-
on. ning, accompanied by an audible
If it remains on or comes on above signal and the message on the multi-
8 mph (12 kmh), this indicates a mal- function display:
function of the ABS. - ''Antipollution fault'', it indicates a
However, the vehicle retains conven- malfunction in the emission control
tional servo-assisted braking. system.
Illumination of this light is accom- - ''Unblock diesel ilter'' indicates
panied by an audible signal and the the start of saturation of the par-
message ''ABS fault'' on the multi- ticulate emission ilter (due to ex-
function display. ceptionally prolonged urban driving
Contact a PEUGEOT dealer. conditions: reduced speed, long
trafic jams, ...).
15-03-2004
22
INSTRUMENTS AND CONTROLS
Diesel pre-heat light Passenger air bag Seat belt not fastened
This comes on each time the disarmed indicator warning light
ignition is switched on. light With the engine running,
Wait until it goes out before Illumination of this warning this indicator light comes
trying the starter. light is accompanied by a message on when the driver's seat belt is not
"Passenger air bag deactivated" fastened.
on the multi-function display.
If the passager air bag is disarmed,
the indicator light comes on when the
ignition is switched on and remains
on.
In all cases, if the warning light lash-
es, contact a PEUGEOT dealer.
15-03-2004
23
INSTRUMENTS AND CONTROLS
Automatic gearbox selector Automatic gearbox indicator
lever positions display screen lights
"SPORT" indicator
Park light
This comes on when the
"SPORT" programme on
the automatic gearbox is
Reverse selected.
15-03-2004
24
INSTRUMENTS AND CONTROLS
INSTRUMENT PANEL Operation The distance remaining to the
DISPLAY next service is less than 500 miles
For 5 seconds after the ignition is (1,000 km).
After switching on the ignition, three switched on, the spanner symbolis-
ing the servicing operations comes Example: 400 miles (900 km) re-
functions are shown in succession: main before the next service.
- service indicator, on; the distance recorder display
indicates the number of miles [kilo- For 5 seconds after the ignition is
- engine oil level indicator, metres] (rounded off) remaining until switched on, the indicator displays:
- total distance recorder (total and the next service.
trip distances). Example: 4,800 miles/km remain
Note: the total and trip distances are before the next service.
displayed for 30 seconds when the For ive seconds after the ignition is
ignition is switched off, on opening switched on, the display indicates:
the driver's door, as well as on lock-
ing and unlocking the vehicle.
15-03-2004
24
INSTRUMENTS AND CONTROLS
INSTRUMENT PANEL Operation The distance remaining to the
DISPLAY next service is less than 500 miles
For 5 seconds after the ignition is (1,000 km).
After switching on the ignition, three switched on, the spanner symbolis-
ing the servicing operations comes Example: 400 miles (900 km) re-
functions are shown in succession: main before the next service.
- service indicator, on; the distance recorder display
indicates the number of miles [kilo- For 5 seconds after the ignition is
- engine oil level indicator, metres] (rounded off) remaining until switched on, the indicator displays:
- total distance recorder (total and the next service.
trip distances). Example: 4,800 miles/km remain
Note: the total and trip distances are before the next service.
displayed for 30 seconds when the For ive seconds after the ignition is
ignition is switched off, on opening switched on, the display indicates:
the driver's door, as well as on lock-
ing and unlocking the vehicle.
15-03-2004
25
INSTRUMENTS AND CONTROLS
The service is overdue. Engine oil level indicator Oil level gauge fault
The service spanner lashes for When the ignition is switched on,
5 seconds after the ignition is the engine oil level is indicated for
switched on. approximately 10 seconds, after the
service information.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible. Surplus of oil
For 5 seconds after the ignition is
switched on, the display indicates: Check the oil level using the dip-
stick.
If the level is correct, the lashing
indicates an actual malfunction of
the engine oil level gauge.
Contact a PEUGEOT dealer.
15-03-2004
25
INSTRUMENTS AND CONTROLS
The service is overdue. Engine oil level indicator Oil level gauge fault
The service spanner lashes for When the ignition is switched on,
5 seconds after the ignition is the engine oil level is indicated for
switched on. approximately 10 seconds, after the
service information.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible. Surplus of oil
For 5 seconds after the ignition is
switched on, the display indicates: Check the oil level using the dip-
stick.
If the level is correct, the lashing
indicates an actual malfunction of
the engine oil level gauge.
Contact a PEUGEOT dealer.
15-03-2004
26
INSTRUMENTS AND CONTROLS
Lighting Service indicator zero re-set
rheostat Your PEUGEOT dealer carries out
With the lights on, press this operation after each service.
the button to vary the However, if you carry out the service
intensity of the lighting yourself, the re-set procedure is as
of the instruments and follows:
controls. When the F Switch off the ignition,
lighting reaches the
minimum (or maximum) setting, re- F Press and hold the trip recorder
lease the button then press it again to re-set button,
increase (or reduce) the brightness. F Switch on the ignition.
As soon as the lighting is of the re- The display begins a countdown.
quired brightness, release the button. When the display shows "0000.0",
release the button; the service sym-
bol disappears.
15-03-2004
27
YOUR 307 SW IN DETAIL
MULTI-FUNCTION SCREENS Monochrome screen CT
and colour screen DT
15-03-2004
28
YOUR 307 SW IN DETAIL
- directory (see "RT3 Parameter configuration
audio/telephone" section),
- telematics (see "RT3
audio/telephone" section),
- coniguration
(see corresponding section),
- map (see section
"Satellite navigation system"),
- video (see corresponding section).
15-03-2004
28
YOUR 307 SW IN DETAIL
- directory (see "RT3 Parameter configuration
audio/telephone" section),
- telematics (see "RT3
audio/telephone" section),
- coniguration
(see corresponding section),
- map (see section
"Satellite navigation system"),
- video (see corresponding section).
15-03-2004
29
YOUR 307 SW IN DETAIL
CT monochrome screen
The "Coniguration" menu gives
access to the following parameters:
• "Adjust the brightness": display
brightness setting. DT colour screen Video
• "Sound": voice synthesiser setting The "Coniguration" menu gives It is possible to connect video equip-
(for the masculine/feminine voice access to the following parameters: ment (a camcorder, digital camera, ...)
parameter: insert the coniguration using the three video sockets situated
CD-Rom); setting of the spoken • "Choose colours": selection from
the palette of colours available for inside the glove box.
commands,
display,
• "International parameters": date and It is only possible to display video
time setting (12 or 24 hour mode, • "Luminosity and brightness": display images when the vehicle is stationary.
adjustment of the minutes on GPS); brightness setting.
units setting (l/100 - °C or mpg - °F), • "Sound": voice synthesiser setting Select the "Video" menu from the
• "Choice of language": selection of the (for the masculine/feminine voice main menu:
language for the display, information parameter: insert the coniguration - "Activate video mode" to activate/
and voice commands (German, Eng- CD-Rom); setting of the spoken cancel the video function,
lish, Spanish, French, Italian, Dutch, commands,
- "Video parameters" to adjust the
Portuguese: insert the coniguration • "International parameters": date and display format, the brightness, con-
CD ROM). time setting (12 or 24 hour mode, trast and colour.
adjustment of the minutes on GPS);
units setting (l/100 - °C or mpg - °F). Press "MODE" or "DARK" to exit video
mode.
• "Choice of language": selection of the
language for the display, information Successive presses on the "SOURCE"
and voice commands (German, Eng- button allow you to select another au-
lish, Spanish, French, Italian, Dutch, dio source other than the video.
Portuguese: insert the coniguration
CD ROM).
For safety reasons, con-
iguration of the multi-func-
tion screens by the driver
must be carried out when
stationary.
15-03-2004
30
YOUR 307 SW IN DETAIL
AUDIO RB3
Button Function
A Radio on/off.
B - Decrease volume.
C + Increase volume.
RDS function on/off.
D RDS Press for more than 2 seconds: regional following mode on/off.
E TA Trafic information priority on/off.
F Press fully: cassette rewind.
G Press fully: fast forward.
34 Press half way: reversal of direction of play of the cassette.
F+G
78 Press fully: ejection of the cassette.
H ¯ Selection of bass, treble, loudness, sound distribution and automatic volume correction.
15-03-2004
35
YOUR 307 SW IN DETAIL
Adjusting the front/rear sound RADIO Selecting radio mode
distribution (Fader)
Notes on radio reception
When "FAD" is displayed, press but- Audio RB3:
ton I or J. Your car radio is subject to phenom- press the "SRC" button
Button I increases the volume in the ena which do not affect domestic several times in succession.
front. radio sets. Both AM (MW/LW) and
FM reception are subject to various
Button J increases the volume in the forms of interference. This is no re-
rear. lection on the quality of the equip- Audio RD3:
ment, but is due to the nature of the press button R.
signals and the way in which they are
Adjusting the right/left sound transmitted.
distribution (Balance) On MW/LW, interference may be
When "BAL" is displayed, press but- noticed when passing under high
ton I or J. voltage power lines or bridges, or in
Button I increases the volume on the tunnels. Selecting a waveband
right-hand side. On FM, interference may be the result
Button J increases the volume on the of increasing distance from the trans- Audio RB3:
left-hand side. mitter, delection of the signals by briely press the "BND/
obstacles (mountains, hills, buildings, AST" button to select
etc.), or of being in an area which is the FM1, FM2, FMast
not covered by a transmitter. and AM wavebands.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Audio RD3:
Press buttons I or J to switch the briely press button R
function on or off. to select the FM1, FM2,
FMast and AM wave-
bands.
15-03-2004
35
YOUR 307 SW IN DETAIL
Adjusting the front/rear sound RADIO Selecting radio mode
distribution (Fader)
Notes on radio reception
When "FAD" is displayed, press but- Audio RB3:
ton I or J. Your car radio is subject to phenom- press the "SRC" button
Button I increases the volume in the ena which do not affect domestic several times in succession.
front. radio sets. Both AM (MW/LW) and
FM reception are subject to various
Button J increases the volume in the forms of interference. This is no re-
rear. lection on the quality of the equip- Audio RD3:
ment, but is due to the nature of the press button R.
signals and the way in which they are
Adjusting the right/left sound transmitted.
distribution (Balance) On MW/LW, interference may be
When "BAL" is displayed, press but- noticed when passing under high
ton I or J. voltage power lines or bridges, or in
Button I increases the volume on the tunnels. Selecting a waveband
right-hand side. On FM, interference may be the result
Button J increases the volume on the of increasing distance from the trans- Audio RB3:
left-hand side. mitter, delection of the signals by briely press the "BND/
obstacles (mountains, hills, buildings, AST" button to select
etc.), or of being in an area which is the FM1, FM2, FMast
not covered by a transmitter. and AM wavebands.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Audio RD3:
Press buttons I or J to switch the briely press button R
function on or off. to select the FM1, FM2,
FMast and AM wave-
bands.
15-03-2004
36
YOUR 307 SW IN DETAIL
Automatic station search Manual station search Automatic storing of FM stations
in the memory (autostore)
Press the "MAN" button.
Briely press button L or N to in- Audio RB3:
crease or decrease the frequency press and hold the
displayed. "BND/AST" button for
By continuing to press the button more than two seconds.
Briely press button L or N to search in the direction selected, you will
for the station immediately above or obtain continuous scrolling of the
below. By continuing to press the frequency.
button in the direction selected, you The scrolling stops as soon as the Audio RD3:
will obtain continuous scrolling of the button is released. press and hold button
frequency. R for more than two
Pressing the "MAN" button again
The scrolling stops at the irst sta- returns you to automatic station seconds.
tion found as soon as the button is search.
released.
If the TA trafic programme is select-
ed, only stations broadcasting this Your radio automatically stores the
type of programme are selected. 6 stations with the strongest signal in
Searching for a station occurs irst FM. These stations are stored in the
in "LO" sensitivity (selection of the FMast waveband.
most powerful transmitters) during Manual storing of stations in the If it is not possible to ind 6 stations,
scanning of the waveband, then in memory the remaining memories are empty.
"DX" sensitivity (selection of the Select the station required.
weakest and most distant transmit- Press one of the buttons "1" to "6"
ters). for more than two seconds.
To make a direct search in "DX" sen- The sound stops then becomes audi-
sitivity, press button L or N twice. ble again, conirming that the station
has been stored in the memory. Recalling stations stored in the
memory
For each waveband, briely press
buttons "1" to "6" to recall the cor-
responding station.
15-03-2004
37
YOUR 307 SW IN DETAIL
RDS Trafic information Regional following mode
programme
Using the RDS (Radio Data When they are part of a network,
System) function on FM Press the "TA" button certain stations broadcast regional
to switch the function programmes in the various areas
Radio Data System allows you to on or off. they serve. With regional following
continue listening to the same sta- The multi-function dis- mode you can keep listening to the
tion, whatever frequency it is using play will show: same programme.
for the region you are going through. Press the "RDS" button for more
- "TA" if the function is selected,
- "(TA)" if the function is selected than two seconds to switch the func-
but not available. tion on or off.
Briely press the "RDS" Any trafic information lash will be
button to switch the given priority, whatever source you
function on or off. are listening to (radio, cassette or
CD changer).
The multi-function dis-
play will show: If you wish to interrupt a message,
press the "TA" button; this switches
- "RDS" if the function is selected. the function off.
- "(RDS)" if the function is selected
but not available. Note: the volume of trafic informa-
tion announcements is indepen-
dent of the volume of normal radio
listening. You can adjust it using
the volume button. The setting will
RDS station following be stored and will be used when
the next messages are broadcast.
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same programme.
15-03-2004
39
YOUR 307 SW IN DETAIL
CASSETTE: AUDIO RB3 Direction of play Recommendations for using
casssettes
Selecting cassette mode The player will play sides 1 and 2 of
the cassette alternately, by automati- - Use good quality cassettes.
cally reversing the direction of play at - Avoid the use of cassettes which
the end of a side. play for longer than 90 minutes.
When a cassette is To manually reverse the direction of - Never expose the cassettes to heat
inserted, the cassette play, press buttons F and G half-way. or the direct rays of the sun.
player will start auto-
matically. - Re-tighten the tape if necessary
If a cassette is already before inserting the cassette into
inserted, press the "SRC" button un- the player.
til cassette mode is selected. - Clean the playing head regularly
Note: before inserting the cassette, Fast forward/rewind with a damp-type cleaning cassette.
ensure that the tape is taut. Fully press button F or G to fast for-
ward or rewind the cassette. At the
end of the fast forward/rewind, the
set plays the current side.
15-03-2004
41
YOUR 307 SW IN DETAIL
CD CHANGER Selecting a disc Accelerated play
Selecting CD changer mode Press buttons "1" to "5" on the radio Press and hold button L or N for for-
to select the corresponding disc. wards or backwards accelerated play.
Accelerated play stops as soon as
the button is released.
Audio RB3:
press the "SRC" button
several times in succession. Selecting a track
Shufle (RDM)
Audio RD3: When the CD changer is selected:
press button P. - audio RB3: press and hold the
Press button L to select the next "SRC" button for two seconds;
track. - audio RD3: press and hold button
Press button N to return to the start P for two seconds.
of the current track or to select the The tracks will be played in random
previous track. sequence. Pressing the button again
for two seconds returns you to nor-
mal play.
15-03-2004
32
YOUR 307 SW IN DETAIL
AUDIO RD3
15-03-2004
33
YOUR 307 SW IN DETAIL
Button Function
A Radio on/off.
B - Decrease volume.
C + Increase volume.
RDS function on/off.
D RDS Press for more than 2 seconds: regional following mode on/off.
Trafic information priority on/off.
E TA Press for more than 2 seconds: PTY function on/off.
H ¯ Selection of bass, treble, loudness, sound distribution and automatic volume correction.
15-03-2004
36
YOUR 307 SW IN DETAIL
Automatic station search Manual station search Automatic storing of FM stations
in the memory (autostore)
Press the "MAN" button.
Briely press button L or N to in- Audio RB3:
crease or decrease the frequency press and hold the
displayed. "BND/AST" button for
By continuing to press the button more than two seconds.
Briely press button L or N to search in the direction selected, you will
for the station immediately above or obtain continuous scrolling of the
below. By continuing to press the frequency.
button in the direction selected, you The scrolling stops as soon as the Audio RD3:
will obtain continuous scrolling of the button is released. press and hold button
frequency. R for more than two
Pressing the "MAN" button again
The scrolling stops at the irst sta- returns you to automatic station seconds.
tion found as soon as the button is search.
released.
If the TA trafic programme is select-
ed, only stations broadcasting this Your radio automatically stores the
type of programme are selected. 6 stations with the strongest signal in
Searching for a station occurs irst FM. These stations are stored in the
in "LO" sensitivity (selection of the FMast waveband.
most powerful transmitters) during Manual storing of stations in the If it is not possible to ind 6 stations,
scanning of the waveband, then in memory the remaining memories are empty.
"DX" sensitivity (selection of the Select the station required.
weakest and most distant transmit- Press one of the buttons "1" to "6"
ters). for more than two seconds.
To make a direct search in "DX" sen- The sound stops then becomes audi-
sitivity, press button L or N twice. ble again, conirming that the station
has been stored in the memory. Recalling stations stored in the
memory
For each waveband, briely press
buttons "1" to "6" to recall the cor-
responding station.
15-03-2004
37
YOUR 307 SW IN DETAIL
RDS Trafic information Regional following mode
programme
Using the RDS (Radio Data When they are part of a network,
System) function on FM Press the "TA" button certain stations broadcast regional
to switch the function programmes in the various areas
Radio Data System allows you to on or off. they serve. With regional following
continue listening to the same sta- The multi-function dis- mode you can keep listening to the
tion, whatever frequency it is using play will show: same programme.
for the region you are going through. Press the "RDS" button for more
- "TA" if the function is selected,
- "(TA)" if the function is selected than two seconds to switch the func-
but not available. tion on or off.
Briely press the "RDS" Any trafic information lash will be
button to switch the given priority, whatever source you
function on or off. are listening to (radio, cassette or
CD changer).
The multi-function dis-
play will show: If you wish to interrupt a message,
press the "TA" button; this switches
- "RDS" if the function is selected. the function off.
- "(RDS)" if the function is selected
but not available. Note: the volume of trafic informa-
tion announcements is indepen-
dent of the volume of normal radio
listening. You can adjust it using
the volume button. The setting will
RDS station following be stored and will be used when
the next messages are broadcast.
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same programme.
15-03-2004
38
YOUR 307 SW IN DETAIL
PTY function: Audio RD3 To search for a PTY programme: EON system: Audio RD3
This allows you to listen to stations This connects stations which are part
broadcasting a speciic type of pro- of the same network. It enables the
gramme (news, culture, sport, rock broadcast of trafic information or a
etc.). PTY programme, by a station that is
part of the same network as the sta-
With FM selected, press tion to which you are listening.
the "TA" button for two
seconds to switch this - select the PTY function, This service is available when you
function on or off. have selected the TA trafic informa-
- briely press button L or N to scroll tion programme or the PTY function.
down the list of the various types of
programmes offered.
- when the programme of your choice
is displayed, keep button L or N
pressed for two seconds to carry
out an automatic search (after an
automatic search the PTY function
is switched off).
In PTY mode the different types of
programmes can be stored in the
memory. To do this, press the prese-
lection buttons "1" to "6" for two sec-
onds. Briely press the corresponding
button to recall the type of programme
stored in the memory.
15-03-2004
40
YOUR 307 SW IN DETAIL
COMPACT DISC: AUDIO RD3 Selecting a track Shufle (RDM)
Selecting CD mode When the CD player is selected,
press and hold button Q for two
seconds. The tracks will be played
After insertion of a disc, in random sequence. Pressing the
printed face upwards, button again for two seconds returns
the player starts auto- Press button L to select the next you to normal play.
matically. track. Shufle mode is de-activated each
If a disc is already inserted, press Press button N to return to the start time the set is switched off.
button Q. of the current track or to select the
previous track.
15-03-2004
43
YOUR 307 SW IN DETAIL
GPS AUDIO/TELEPHONE RT3
Button Function
B 5 Ejection of CD.
Button Function
15-03-2004
47
YOUR 307 SW IN DETAIL
Sound ambience Treble setting Setting the right/left sound
distribution (Balance)
When 'Treble' is displayed, turn but-
This function per- ton G to vary the setting. When "Balance" is displayed:
mits the selection of - Turn button G clockwise to in-
a "None", "Rock", - '-9' for minimum treble setting
- '0' for normal setting crease the volume on the right.
"Classical", "Jazz",
"Vocal" or "Techno" - '+9' for maximum treble setting - Turn button G anti-clockwise to
sound ambience. increase the volume on the left.
Turn button G to se-
lect the sound ambi-
ence.
Selecting "None" permits access
to all of the settings deined below.
Selecting another ambience sets the Adjusting the loudness Automatic volume adjustment
bass and treble automatically. This function allows the volume to
This function automatically empha-
sises bass and treble tones when the be adjusted automatically depending
volume is low. on the level of noise produced by the
Rotate button G to switch the func- speed of the vehicle.
tion on or off. Press button to switch the function
Bass setting on or off.
When 'Bass' is displayed, turn but-
ton G to vary the setting.
- '-9' for minimum bass setting
- '0' for normal setting Setting the front/rear sound
- '+9' for maximum bass setting distribution (Fader)
When 'Fader' is displayed:
- Turn button G clockwise to in-
crease the volume in the front.
- Turn button G anti-clockwise to
increase the volume in the rear.
15-03-2004
48
YOUR 307 SW IN DETAIL
RADIO Selecting the radio Automatic station search
Notes on radio reception
Car radio/telephone receivers are
subject to phenomena which do not
affect domestic radio sets. Both MW/
LW and FM are subject to various Press "SOURCE" several times. Briely press button M or N to search
forms of interference. This is not a for the station immediately above or
relection on the quality of the equip- below.
ment, but is due to the nature of the
signals and the way in which they are The search stops at the irst station
transmitted. found.
On MW/LW interference may be If the TA trafic programme is select-
noticed when passing under high ed, only the most powerful stations
Selecting a waveband broadcasting this type of programme
voltage power lines or bridges, or in
tunnels. are selected.
On FM, interference may be the result Briely pressing button Searching for a station occurs irst in
of the increasing distance from the 'BAND/AST' to select 'LO' sensitivity (selection of the most
transmitter, delection of the signals the FM1, FM2 , FMast powerful transmitters) for scanning of
by obstacles (mountains, hills, build- and AM wavebands. the waveband, then in 'DX' sensitiv-
ings etc.) or of being in an area which ity (selection of the weaker and more
is not covered by a transmitter. distant transmitters).
To make a direct search in 'DX' sen-
sitivity, briely press button M or N
twice.
15-03-2004
49
YOUR 307 SW IN DETAIL
Manual station search Automatic storing of FM stations
in the memory (autostore)
Briely press button H or I Press the ''BAND/
to increase or decrease the AST'' button for more
frequency displayed. than two seconds.
By continuing to press
the button in the direction
selected, you will obtain
continuous scrolling of the Your audio/telephone automatically
frequency. stores the 6 stations with the strong-
Scrolling stops as soon as est signal in FM. These stations are
the button is released. stored in the FMast waveband.
If it is not possible to ind 6 stations,
the remaining memories are empty.
15-03-2004
50
YOUR 307 SW IN DETAIL
RDS Trafic information programme Regional following mode (REG)
Using the RDS (Radio Data When they are part of a network,
System) function on FM certain stations broadcast regional
Press the ''TA/PTY'' programmes in the various areas
Radio Data System allows you to button to switch the they serve. With regional following
continue listening to the same sta- function on or off. mode you can keep listening to the
tion, whatever frequency it is using same programme.
for the region you are going through. The multi-function screen will show:
To do this, press the "RDS" button
- TA if the function is selected for more than two seconds to switch
- TA crossed out or greyed out the function on or off.
if the function is selected but not The multi-function screen will show:
available.
Briely press the - REG if the function is active,
Any trafic information lash will be
"RDS" button to switch given priority, whatever source you - REG crossed out or greyed out
the function on or off. are listening to (radio, CD or CD if the function is active but not
The multi-function changer). available.
screen will show: If you wish to interrupt the broadcast-
- RDS if the function is active ing of a message, press the ''TA/
- RDS crossed out or greyed out if PTY'' button.
the function is active but not avail- Note: the volume of the trafic
able. information is independent of the
volume of normal radio/telephone
listening.
You can adjust it by using the volume
button. The setting will be stored and
will be used when the next messages
are broadcast.
RDS station following
This display indicates the name of the
station selected. The audio/telephone
continuously searches for the trans-
mitter which transmits the same pro-
gramme with the best reception. This
search may cause slight interference
with the transmission.
15-03-2004
51
YOUR 307 SW IN DETAIL
PTY function EON system Contextual menu
This allows you to listen to stations This system connects stations which
broadcasting a speciic type of pro- are part of the same network. It
gramme (news, culture, sport, rock enables the broadcast of trafic in-
etc.). formation or a PTY programme, by
When FM is selected, press button a station that is part of the same
"TA/PTY" for more than two seconds network as the station to which you
to switch the function on or off. are listening.
To ind a PTY programme: The service is available when you By pressing knob G, the contextual
have selected the TA trafic informa- menu allows you to access the fol-
tion programme or the PTY function. lowing functions:
- 'Enter a frequency',
- 'List of stations' to access directly
the 30 stations picked up locally,
- 'Refresh list' to update this list,
- select the PTY button, - "Display Radio Text" to display
Audio functions menu
- turn button G to scroll down the information connected with the
different types of programmes of- Select the "Audio functions" menu station being listened to, if "RT" is
fered, then conirm your choice, from the general menu to: displayed permanently.
- when the programme of your - "Activate/Deactivate RDS frequency
choice is displayed press button following",
M or N to carry out an automatic - "Activate/Deactivate REG regional
search (after an automatic search mode",
the PTY function is switched off if - "Trafic information TMC".
no station has been found).
15-03-2004
52
YOUR 307 SW IN DETAIL
COMPACT DISC Selecting a track Contextual menu
Selecting CD mode
Accelerated play
Press and hold button M or N for
forwards or backwards accelerated
Ejecting a disc play.
Accelerated play stops as soon as
Press button B to the button is released.
eject the disc from the
drive.
15-03-2004
53
YOUR 307 SW IN DETAIL
COMPACT DISC CHANGER Selecting a track Contextual menu
Selecting CD changer mode
15-03-2004
54
YOUR 307 SW IN DETAIL
TELEPHONE Using the menus Within each menu:
This function is a GSM dual-band Press the ''MENU'' button to dis-
telephone (900 and 1 800 MHz) play the general menu. Select the Move around and se-
incorporated in the RT3 GPS audio/ telematics application, validate lect a function by turn-
telephone system. "Telephone functions" to access ing the G button then
It is a ''hands free'' telephone. This the principal telephone functions, validate by pressing
function is provided by a microphone then the various menus, in order to the button.
located next to the front courtesy reach the one required. Cancel an operation us-
light, the speakers, a steering col- This menu allows you to access the ing the ''ESC'' button.
umn control and voice commands following functions:
which allow access to most of the
functions (the audio/telephone con-
trol panel buttons allow access to all
the functions). Using the alphanumeric keypad
Display of the principal ''mobile''
type functions, as well as consulta- For a given button, to input a charac-
tion of the directories, is provided by ter in the second or subsequent rows
the multi-function display. press until you obtain the character
required.
This function is active, whatever
position the ignition key is in even af- - Network: allows you to select the
ter thirty minutes, when the message network search mode and to see
''Economy mode active'' appears the networks available. Buttons Associated characters
on the multi-function display. - Duration of calls: allows you to [1] 1 or space
consult the duration recorder of [2] 2 or A B C 2 or a b c 2
calls made and zero re-set.
[3] 3 or D E F 3 or d e f 3
- Security: allows you to use or [4] 4 or G H I 4 or g h i 4
modify the PIN code and to erase
the list of calls and text messages [5] 5 or J K L 5 or j k l 5
(SMS). [6] 6 or M N O 6 or m n o 6
- Telephone options: allows you to [7] 7 or P Q R S 7 or p q r s 7
conigure the calls with entering of [8] 8 or T U V 8 or t u v 8
my number, automatic answering [9] 9 or W X Y Z 9 or w x y z 9
after X rings, speciication of ring [0] 0 or + (long press)
options and allows you to conigure
the call diversion number. [#] # or validation
[*] * or erasing of last charac-
ter input (long press)
15-03-2004
55
YOUR 307 SW IN DETAIL
Installing the SIM card Inputting the PIN code Cancelling of PIN code request
In the menu ''Telephone functions''
Open lap L by pressing the select ''Security'', then ''Process
point of a pencil on the circu- the PIN code'', then validate the
lar opening above the lap. ''Cancel'' function.
Warning: in this case, do not lose
Insert your Micro-SIM card, your SIM card. Losing it would mean
available from a mobile anyone who inds it would be able to
telephone operator, as indicated in make unlimited calls.
the graphics, then close the lap.
Note: removal or insertion of the SIM
card must only be carried out after
the RT3 audio/telephone has been
switched off. Input your PIN code using the al-
phanumeric keypad and validate by
pressing button G or button # to ac-
cess the network. Connection to the
network is validated by the appear-
ance of a symbol on the screen.
Warning: if you make three errors in
succession when inputting your PIN
code, your SIM card will be blocked.
To unblock it, you will need to input
the PUK code. The PUK code will be
supplied to you by the person sell-
ing your SIM card (input of the PUK
code allows for 10 errors in succes-
sion; after this the SIM card becomes
permanently unusable).
Note: the PIN code is required each
time the ignition is switched on, un-
less the PIN code has been stored
in the memory or protection by PIN
code is not activated on the SIM
card.
15-03-2004
56
YOUR 307 SW IN DETAIL
Telephone function screens Making a call Making a call from a directory
Not in use Select the "Directory" function to
access all the iles containing a tele-
phone number or the "List of calls"
function to access the list of the
last twenty incoming (if the number
display option is active) or outgoing
calls.
Press button D to display the contex- Note: there are two directories, the
tual menu of the telephone. RT3 GPS audio/telephone directory
This screen indicates the presence
of voice messages or text mes- Note: pressing the end 5 of the and the SIM card directory. To con-
sages (SMS) not listened to/read, steering column control for more sult the SIM directory, insert your
the cumulative time in use since the than 2 seconds calls up a contex- SIM card and enter your PIN code.
last zero reset and the status of your tual menu limited to the "Directory",
telephone. "List of calls" and "Voice mail"
functions.
Receiving a call
When a ringing
In use Entering a number sounds to let you
know that a call is
Select the function waiting, you can
''Enter number'' then choose either to ac-
enter the number of cept it by pressing
the person you wish button D or the end
to speak to using the of the steering wheel
alphanumeric key- remote control or not to accept it by
pad. pressing the button Q or by selecting
This screen indicates the time and validating the "NO" button on
elapsed since the start of the con- Press button D to the "Answer?" screen.
versation, as well as the number* or make the call.
name of the person to whom you are If you accept the call, to end your
speaking (if recorded in the directory) communication, press button Q.
and the status of your telephone. If you do not accept the call, it is
transferred to your voice mail or to a
call diversion number.
You can activate or deactivate this
transfer by pressing button Q for
more than two seconds.
* If this option and service are avail-
able.
15-03-2004
57
YOUR 307 SW IN DETAIL
Text messages (SMS) Sending a text message "Duration of calls" menu
Accessing text messages Select the "Duration of calls"
function from the "Telephone func-
tions" menu to consult the duration
counters for the calls made. The par-
tial counter totals the duration of the
calls since the last zero reset carried
out using the "Zero reset" button.
Note: Before typing your irst text
message, check that your text mes-
When the buzzer sounds (if the SMS sages (SMS) centre number is stored
text messages buzzer option is ac- correctly in the sub-menu "Server
tive) and a superimposed screen centre N°". If it is not, any text mes- "Telephone options" menu
announces "Do you wish to read sages typed before this number is
the new text message (SMS)?", entered will not be sent. Select the "Telephone options"
you can choose to read the text mes- function from the "Telephone func-
sage received by selecting and vali- In the menu "Text messages tions" menu to access the func-
dating "YES" or postpone reading (SMS)" validate the function "Text tions:
it by selecting and validating "NO", message writing". Type your text
message using the alphanumeric • "Conigure the calls" which per-
by pressing the "ESC" button or by mits activation and deactivation of
waiting until the announcement dis- keypad and validate it using the
"OK" button to store it or validate the the "show my number" and "auto-
appears. The message is read by the matic answering after "X" rings"
voice synthesiser, if it is active. "Send" button to send it. Validation
of the "Send" button enables you to functions.
enter the number of your recipient or • "Ringing options" which permits
Note: the old text messages stored and select it from the directory or from the adjustment of the ringing volume
the new text messages, the reading of list of calls and send the message. for voice calls, activation of the text
which you wished to postpone, can be messages (SMS) receipt buzzer
consulted. Press the "MENU" button and selection of a ring tone from
then validate the telematic icon, select the ive offered.
"Text messages (SMS)" and validate • "Diversion number/voice mail"
the function "Received text messages which permits recording of the call
reading" by pressing button G. Then diversion number chosen by the
scroll through the list by turning the customer, otherwise the call will be
button and press the button to select transferred to the voice mail.
the text message to be read.
15-03-2004
58
YOUR 307 SW IN DETAIL
Services* Emergency call*
15-03-2004
60
YOUR 307 SW IN DETAIL
VOICE COMMANDS List of commands available - For navigation/guidance, say
"NAVIGATION" or "GUIDANCE",
The voice commands make it pos- - For the radio, say "RADIO", then: then:
sible to use pre-recorded words or "PREVIOUS" / "NEXT" /
phrases to control a certain number "STOP" / "RE-START" /
"MEMORY" + 1...6 / "ADDRESS BOOK" +
of functions of the RT3 GPS audio/ "AUTOSTORE" / "LIST"
telephone. DESCRIPTION / "ZOOM IN" /
- For the CD, say "CD PLAYER", "ZOOM OUT" / "SHOW" +
Activation of the voice commands then: "DESTINATION" / "SHOW" +
Press the button on the end of the " PREVIOUS TRACK" / "NEXT "VEHICLE"
lights stalk to activate or deactivate TRACK" / "TRACK NUMBER" + - To change the permanent
this function. 1...20 / "RANDOM" / "SCAN" / application, say "DISPLAY", then:
Example: to recall the radio station "LIST" "AUDIO" / "TELEPHONE" /
stored on button 3, the key words - For the CD changer, say "NAVIGATION" / "TRIP
are: "Radio" "Memory" "3". "CHANGER", then: COMPUTER" / "GUIDANCE"
To use these key words, you must " PREVIOUS TRACK" / "NEXT - To call someone recorded in the
say the word "Radio", wait for the TRACK" / "TRACK NUMBER" + directory directly, say "CALL" +
audible conirmation signal, then 1...20 / "PREVIOUS DISC" / DESCRIPTION
say the word "Memory", wait for the "NEXT DISC" / - To be guided to the address of
audible conirmation signal, then end "DISC NUMBER" + 1...5 / someone recorded in the
with the word "3", wait for the audible "RANDOM" / "SCAN" / directory, say "GUIDE TO" +
conirmation signal which will carry "REPEAT" / "LIST" DESCRIPTION
out the action requested. - For the telephone, say - Various:
Notes: "TELEPHONE", then: "CANCEL" / "HELP" / "WHAT
- between two key words, a screen "REDIAL" / "ADDRESS BOOK" + CAN I SAY" / "STOP" /
indicates the time remaining and DESCRIPTION / "SERVICES" / "DELETE" / "YES" / "NO" /
the key word recognised, "SOUND BOX" / "VOICE "PREVIOUS" / "NEXT"
- in the absence of any voice MESSAGE"
commands, this function will be - For the SMS text messages, say
switched off after approximately "SMS" or "MESSAGE" then:
ive seconds, "DISPLAY" / "READ"
- if a command is not understood, - For the RDS traffic information
the system transmits "Pardon" TMC, say "TRAFFIC-INFO" then:
and displays "Word not recog- "DISPLAY" / "READ"
nised" on the screen.
Saying the phrase "Help" or "What
can I say" displays all of the com-
mands available on the screen.
15-03-2004
61
YOUR 307 SW IN DETAIL
CD CHANGER
15-03-2004
62
YOUR 307 SW IN DETAIL
SATELLITE NAVIGATION The CD-Rom drive
SYSTEM
This is part of the RT3 GPS audio/
Introduction telephone.
The satellite navigation system guides
you, by means of vocal and visual in-
structions (graphics), to your chosen
destination.
The heart of the system lies in the
use of a map data base and GPS
(Global Positioning System). With
this system you can ix the position 1. Ejection button on CD-Rom. The last voice message recall
of your vehicle by means of a satel- 2. CD-Rom housing. control.
lite network.
The system uses the following ele-
ments:
- the CD-Rom drive,
The navigation CD-Rom
- the coniguration CD-Rom,
- the navigation CD-Rom,
- the last voice message recall con-
trol,
- the control keypad,
This contains all the map data. Pressing for more than two seconds on
- the CT monochrome screen or the
DT colour screen. It must be inserted in the drive, print- the button at the end of the lights stalk
ed face upwards. repeats the last voice information.
Use only CD-Roms approved by
Certain functions or services de- PEUGEOT.
scribed may vary depending on
the version of CD-Rom or the
country where the vehicle is sold.
15-03-2004
63
YOUR 307 SW IN DETAIL
The control keypad Rotation of the dial: "MODE" button:
This allows you to move round the - brief press: modiication of per-
screen and thus select a function. manent display (audio system,
It also allows you: navigation/guidance...),
- with a 'setting' type parameter, - Press for more than two seconds:
after selection, to increase or de- display of general information.
crease the value,
- with a 'list' type parameter, to open 'ESC' button:
the list and scroll through the val-
ues, - brief press: cancelling of opera-
tion in progress or erasing of last
- with map guidance, to increase the superimposed display.
zoom.
- pressing for more than two sec-
This lets you select and validate the onds: erasing of all superimposed
functions, controls and programmes Pressing the dial: displays and return to the perma-
displayed. nent display.
This allows:
- access to the list of controls (con-
textual menu) of the permanent 'MENU' button:
display, if there is no other display - Brief press: access to the general
superimposed. menu.
- conirmation of the selected func- - Press for more than two seconds:
tion or the modiied value. access to the help menu.
- selection of a 'setting' or 'list'
type parameter for modiication.
Tip:
You can access the general menu
by pressing the dial of the RT3 GPS
audio/telephone.
15-03-2004
64
YOUR 307 SW IN DETAIL
General notes on the display General menu
Switch on the RT3 GPS audio/
Monochrome screen CT Colour screen DT telephone and insert the navigation
CD-Rom.
Press the "MENU" button to access
1 2 3 1 2 3 the general menu.
7 6 5 4 7 6 5 4
During guidance, if the navigation Notes:
CD-Rom is present, the screen dis-
plays different information depend- - depending on the situation of the
ing on the manoeuvres to be carried vehicle and on the reception of
out. GPS information, this information
may disappear from the screen
1. Current manoeuvre or com- temporarily,
pass or course (if calculation in - during guidance, the navigation CD
progress or zone not mapped). ROM must remain in the RT3 GPS Select the Navigation/Guidance icon
audio/telephone. using the dial G, then validate by
2. Next manoeuvre to be carried
out. pressing the dial to access the main
"Navigation - Guidance" menu.
3. Next road to be taken.
4. Current road.
5. Estimated time of arrival at desti-
nation.
6. Distance to inal destination.
7. Distance to next manoeuvre.
15-03-2004
65
YOUR 307 SW IN DETAIL
Navigation - Guidance Selecting a destination Entering an address
The main "Navigation - Guidance" The "Destination choice" menu The last guidance address is dis-
menu offers various options for acti- offers various options for reaching a played.
vation or management of guidance: destination: Select and validate in succession the
- choice of the type of destination • entering a postal address, entry zones "Town", "Road", then
address (entering of address, • selecting a service available in a "N°" to ill them in.
service, GPS co-ordinates, stored town (town hall, hotel, cinema, air- The "OK" function permits valida-
address), port...), tion of the address and access to the
- modiication to the initial route (en- • entering GPS details, guidance activation function.
tering of a diversion), The "Store" function permits record-
• selecting a destination stored in the
- displaying of the chosen destina- directory, ing of the address in a directory ile.
tion,
• selecting one of the previous The "Curr. loc" function permits dis-
- setting of the guidance option pa- destinations. play of the current address.
rameters,
- stop or resume guidance (display-
ing of the message which changes
depending on the previous status).
15-03-2004
66
YOUR 307 SW IN DETAIL
Entering the name of the town When the list contains fewer than ive Entering the number of the road
names, these are displayed automat- or junction
ically. Select a town then validate by
pressing the dial.
When the complete name of the town
is displayed, select the "OK" function
then conirm by pressing the dial.
Note: once the town has been en-
tered, you can conirm by pressing
"OK". You will then be guided to the
centre of this town automatically.
15-03-2004
67
YOUR 307 SW IN DETAIL
Selecting a service Note: if the service selected is not GPS details
available in the programmed loca-
If you wish to be directed to a serv- tion, a temporary message informs
ice, select the category correspond- you of this.
ing to the service, then conirm by
pressing the dial. Following validation of the location,
the service closest to it is displayed.
The list of services corresponding to The distance indicated is the dis-
the category selected is displayed. tance as the crow lies from the serv-
Select the service then conirm ice to the selected location.
by pressing the dial to access the
"Choice of a location" function.
Select the ''Directory'' function to Select the "Previous destinations" Activate the function ''Divert route'',
access the ile in which the address function to access one of the last then input the distance involved in
you are looking for is archived. twenty addresses stored. the change required.
Select the ''OK'' function then vali-
Select a description by scrolling Select a description by scrolling date by pressing the dial.
down the list by means of the dial, down the list by means of the dial, The system calculates the change
then conirm by pressing the dial. then conirm it by pressing the dial. which is closest to the value input
The directory ile is then displayed. The complete address is then dis- and gives you the option of whether
Select the "OK" function, then press played. or not to use this change.
the dial to access the guidance acti- Select the "OK" function, then press
vation function. the dial to access the guidance acti- Details of the route
Follow the directions given by the vation function.
system. Follow the instructions given by You can consult the destination ad-
the system. dress at any time by activating the
"Chosen destination" function on
the "Navigation - Guidance" menu.
15-03-2004
69
YOUR 307 SW IN DETAIL
Guidance options Calculation criteria Note: the volume can also be ad-
justed during a message, using the
audio/telephone button or the steer-
ing wheel control.
The menu ''Guidance options'' The last criterion used is displayed. Stopping / Resuming guidance
provides access to the following Select a criterion from the list, then
functions: validate by pressing the dial. • "Stop guidance"
- changing of the route calculation During guidance, select this func-
When the criterion of your choice tion then validate.
criteria, has been selected, select the "OK"
- voice synthesis adjustment of guid- • "Resume guidance"
function then conirm by pressing
ance messages, the dial. In the absence of guidance, select
this function then validate to acti-
- description of the information relat- Adjusting the voice synthesiser vate guidance to the last destina-
ing to the navigation CD-Rom, tion programmed.
- management of the addresses Select the type of voice "male" or
stored in the directory. "female", after inserting the conigu-
ration CD-Rom. Note: after re-starting the engine,
a screen appears enabling you to
Adjust the volume of the voice syn- resume the guidance activated be-
thesis by turning the dial, then vali- fore the ignition was switched off.
date by pressing the dial.
15-03-2004
70
YOUR 307 SW IN DETAIL
"Navigation - Guidance" TMC (Trafic Message Channel) Select the "TMC Trafic Informa-
contextual menu RDS Trafic Information tion" function on the "Telematics"
menu, you can choose:
This function enables you to re- - "Consult the messages" to display
ceive messages regarding the trafic the list of TMC messages available,
conditions (accidents, trafic jams, - "Filter the TMC information" to se-
weather, ...). lect one or more types of message
They may appear temporarily as a and initialise the TMC station,
superimposed display or be read by - "Voice synthesiser" to listen to the
the voice synthesiser, if it is active. TMC messages received,
- "Activate/Deactivate trafic infor-
mation" to display or not display
the TMC messages received.
15-03-2004
71
YOUR 307 SW IN DETAIL
Filtering the TMC messages General notes on the "Map" In "Selection-movement on map"
application** mode, you can see symbols, repre-
senting the various types of services
The "Map" application has two dis- which exist, sorted by category:
play modes:
- "Administration and safety" symbol
- "Vehicle following on map" on a grey background,
mode, representing active guid-
ance on the map on the right and - "Hotels, bars and restaurants"
a large-scale view of the next inter- symbol on a yellow background,
section on the left, - "Other businesses" symbol on a
- "Selection - Movement on map" purple background,
mode, representing consultation - "Culture, tourism and entertain-
of the map at full screen size or ment" symbol on a white back-
reduced size on the right with a ground,
compass on the left. - "Sports centres and open air
centres" symbol on a green back-
To switch from one mode to the other, ground,
press the dial on the right briely, then - "Transporation and automobiles"
select the "Move the map" or "Exit symbol on a blue background.
To ilter these messages, select the the map mode" function.
"Filter the TMC information" func- A "Zoom" function enables you to
tion from the "Trafic Information enlarge the map, in accordance with
TMC" menu, you then obtain: the thirteen preset levels relating to
- "Route information ilter" to obtain the following scales:
the messages relating to the cur- - 50 m/cm, 100 m/cm, 150 m/cm,
rent guidance outline, 200 m/cm, 500 m/cm,
- "Filter by event" to display the mes- - 1 km/cm, 2 km/cm, 5 km/cm,
sages speciic only to accidents, or
trafic jams, or..., - 10 km/cm, 20 km/cm, 50 km/cm,
- "Geographic ilter" to take into ac- - 100 km/cm, 200 km/cm.
count the messages within a radius This is achieved by turning the dial.
of action to be deined around the
vehicle and/or a location.
You can ilter these messages using
one or more ilters simultaneously.
15-03-2004
72
YOUR 307 SW IN DETAIL
"Vehicle following on map" mode "Selection - Movement on map" Map
mode
This mode permits: This mode permits: From the general menu, the main
- displaying of the vehicle on the - selection of any point on the map "Map" menu offers various options
map with the route proposed by to obtain guidance towards it or to for guidance management:
the navigation if the guidance is obtain information about it (postal - switching to "Selection - Movement
active, address if available or, if it is not, on map" mode,
- zooming in on the map in accord- GPS co-ordinates), - direction of the map towards the North
ance with the thirteen preset levels, - movement on the map by means or in the direction of the vehicle,
- displaying of the "Navigation - of the four directional arrows, rep- - recentering of the map around the
Guidance" contextual menu. resenting the four cardinal points vehicle,
(North, East, South, West),
- opening of the services selection
- zooming in on the map in accord- window visible on the map, such
ance with the thirteen preset levels, as hotels, service stations, etc,
- displaying of the "Map" contextual - displaying of the window for enter-
menu. ing the description for recording the
current position of the vehicle in a
directory ile.
15-03-2004
73
YOUR 307 SW IN DETAIL
"Map" contextual menu
15-03-2004
74
YOUR 307 SW IN DETAIL
15-03-2004
75
YOUR 307 SW IN DETAIL
VENTILATION Advice on operation
1. Windscreen de-icing or demisting F Place the air low control at a
vents. level suficient to ensure a good
2. Front window de-icing or renewal of air in the passenger
demisting vents. compartment.
The ''OFF'' position cuts off all the
3. Side vents. air circulation in the passenger
4. Centre vents. compartment.
5. Air outlet to front footwells. Note: only use the ''OFF'' position
occasionally (risk of condensation).
6. Air outlet to rear footwells.
F For perfectly even air distribution,
take care not to obstruct the ex-
terior air intake grilles, the vents
and the air ducts under the front
seats, as well as the air extractor
located in the boot. Check that the
passenger compartment ilter is in
good condition.
15-03-2004
76
YOUR 307 SW IN DETAIL
AIR CONDITIONING 3. Air distribution adjustment
2. Temperature adjustment
Press the switch, the indica-
tor light comes on. To be adjusted to your requirements.
15-03-2004
77
YOUR 307 SW IN DETAIL
4. Air low adjustment 5. Air intake 6. Demisting the rear screen and
the mirrors
Turn the control from posi- Pressing button 5 permits re- With the engine running,
tion 1 to position 4 to obtain circulation of the interior air. pressing the button once
an air low suficient to en- Recirculation, indicated by demists the rear screen and
sure your comfort. illumination of the indicator the mirrors.
light, prevents exterior odours and This switches off automatically after
smoke from entering the passenger approximately twelve minutes.
compartment.
Pressing again activates demisting
Used simultaneously with the air for a further twelve minutes.
conditioning, recirculation enables
cooling performance to be improved. It is possible to stop demisting by
pressing the button again before the
Used in a humid climate, recircu- end of the twelve minutes.
lation may result in misting of the
windows.
As soon as possible, switch button 5 Important precaution
to the outside air position, to prevent Operate the air conditioning system
deterioration of the air quality. The for 5 to 10 minutes, once or twice a
indicator light switches off. month, to keep it in perfect working
order.
If the system does not produce
cold air, do not use it and contact a
PEUGEOT dealer.
15-03-2004
78
YOUR 307 SW IN DETAIL
AUTOMATIC AIR CONDITIONING Note: for your comfort, when the
engine is switched off, the settings are
retained until the engine is switched
on again, if the temperature in the
passenger compartment has not al-
tered signiicantly; otherwise, opera-
tion resumes in automatic mode.
15-03-2004
79
YOUR 307 SW IN DETAIL
4. Air conditioning 6. Air low 8. Switching the system off
Press this button to stop air The low of air can be The OFF button switches
cooling. The symbol ECO is increased or reduced off all the functions of the
displayed. Automatic opera- by pressing buttons + system.
tion of the air conditioning is or - respectively. Temperature-related comfort
resumed when the button is pressed is no longer guaranteed but a slight
again. The symbol A/C is displayed. low of air is maintained to prevent
condensation and to renew the air.
Pressing the OFF, AUTO, or vis-
7. Air intake ibility button again reactivates the
system with the values set before it
Note was switched off.
It is quite normal that the condensa- Press this button for recir-
culation of the interior air. Note: if you wish to cut off the low
tion created by the air conditioning of air completely, press the air intake
results in a low of water under the Recirculation, shown on the
display, enables the passen- button 7.
vehicle when it is stationary.
ger compartment to be isolated from
To prevent condensation on the exterior odours and smoke.
inside of the vehicle in cold or wet 9. Demisting the rear screen and
weather, you are advised to avoid Avoid prolonged recirculation of inte- the mirrors
using the ECO mode. rior air. To do this, press the button
again to resume automatic manage- Press this button to demist
ment of the intake of air. the rear screen and the mir-
rors. Demisting switches off
5. Air distribution Note: To prevent condensation on automatically. It is possible
the inside of the vehicle in cold or wet to stop operation of the demisting
weather, you are advised to avoid us- before it is switched off automatically
Pressing this button several ing this mode.
times in succession enables by pressing the button again.
the air low to be directed in
turn towards:
- the windscreen (de-icing or demisting),
- the windscreen and the footwells, Important precaution
- the footwells, Operate the air conditioning for 5 to
- the centre and side vents and the 10 minutes, once or twice a month, to
footwells, keep it in good working order.
- the centre and side vents. If the system does not produce cold
air, do not use it and contact your
PEUGEOT dealer.
15-03-2004
80
YOUR 307 SW IN DETAIL
FRONT SEATS
1 - Forwards/backwards
adjustment
Lift the control and slide the seat
forwards or backwards.
4 - Armrests
These can be folded down and are
removable.
To remove them, press the button
located between the armrest and the
side of the seat and pull it.
15-03-2004
81
YOUR 307 SW IN DETAIL
5 - Head restraint height and Active seat back (front seat) REAR HEAD RESTRAINTS
angle adjustment
This possesses a device to prevent These have a high position for when
To raise or lower the restraint, pull it 'whiplash'. they are in use and a low position for
forwards, sliding it at the same time. when they are stored.
When there is an impact from the
rear, the action of the body on the The head restraints are also remov-
seat back forces the head restraint able.
The adjustment is correct when forwards and upwards, preventing
the upper edge of the head re- To remove them, pull upwards as
the head being thrown backwards. far as the stop, then press the lug
straint is level with the top of
the head. (side seat) or on the two lugs (centre
6 - Storage drawers seat).
There is a storage drawer under
each front seat.
- To open it, lift it and pull.
- To take it out, open it to its full extent,
press the ends of the slides and lift
it, then remove it completely.
- To put it back in place, at the end
of its travel, press the top of the
drawer to secure it.
To remove the head restraint, place it
almost in the top position, lift the lug Do not place heavy objects in the
using a coin and pull it. drawers.
To put it back in position, locate the
stems of the restraint in the holes, Under the front passenger seat, the
taking care to keep them in line with layout of the loor allows for storage
the seat back. of a irst aid kit and a warning triangle
(small version).
15-03-2004
81
YOUR 307 SW IN DETAIL
5 - Head restraint height and Active seat back (front seat) REAR HEAD RESTRAINTS
angle adjustment
This possesses a device to prevent These have a high position for when
To raise or lower the restraint, pull it 'whiplash'. they are in use and a low position for
forwards, sliding it at the same time. when they are stored.
When there is an impact from the
rear, the action of the body on the The head restraints are also remov-
seat back forces the head restraint able.
The adjustment is correct when forwards and upwards, preventing
the upper edge of the head re- To remove them, pull upwards as
the head being thrown backwards. far as the stop, then press the lug
straint is level with the top of
the head. (side seat) or on the two lugs (centre
6 - Storage drawers seat).
There is a storage drawer under
each front seat.
- To open it, lift it and pull.
- To take it out, open it to its full extent,
press the ends of the slides and lift
it, then remove it completely.
- To put it back in place, at the end
of its travel, press the top of the
drawer to secure it.
To remove the head restraint, place it
almost in the top position, lift the lug Do not place heavy objects in the
using a coin and pull it. drawers.
To put it back in position, locate the
stems of the restraint in the holes, Under the front passenger seat, the
taking care to keep them in line with layout of the loor allows for storage
the seat back. of a irst aid kit and a warning triangle
(small version).
15-03-2004
82
YOUR 307 SW IN DETAIL
REAR SEATS Folding a side seat: Fold the seat back onto the cushion
using the strap C.
Forwards-backwards adjustment* access to the 3rd row:
Note: you can lock the seat back
Lift the bar A and slide the seat Place the head restraint in the low in this position (for removal) by
forwards or backwards. position. pressing down on it.
From the 3rd row, you can pull the Push the seat back fully using bar Push the control D upwards to
strap B and slide the seat forwards A. release the rear feet.
or backwards. Fold the seat back onto the cushion Place the seat in the folded position.
This manoeuvre makes it easier for using the strap C.
passengers to exit the 3rd row, when Note: you can lock the seat back While driving attach the retaining
the 2nd row seat is folded. in this position (e.g. for removal) by strap (contained in the storage
pressing down on it. pocket of a front seat):
Seat back angle adjustment Push control D upwards to release - on the 2nd row: on one side, to
Pull one strap C (two straps for each the rear feet. the carrying handle G and on
side seat, one for the centre seat) Place the seat in the "folded" position. the other side, to the grab han-
and adjust to the required angle. dle,
Release the strap to lock. - on the 3rd row: on one side, to
exit from the 3rd row or folding the carrying handle G and on
To adjust the angle of the seat from from the boot: the other side, to the rear arm-
the 3rd row or the boot, pull the strap rest grab handle.
C at the rear of the seat. Place the head restraint in the low
position.
Note: the additional seat can be an-
gled and folded by means of a single Push the seat back fully using the
strap C at the rear of the seat on the strap B.
right or on the left.
Centre seat table position Folding the centre seat Folding an additional seat
Place the head restraint in the low Place the head restraint in the low Place the head restraint in the low
position. position. position.
Fold the seat back onto the cushion Push the seat back fully using the Pull the strap C (at the rear of the
using the strap C. bar A or the strap B. seat to the right or to the left) back-
You now have a small table with four Fold the seat back onto the cushion wards then press on the seat back to
can holders, two pen holders and a using the strap C. release it, while continuing to pull the
document holder. strap.
Note: you can lock the seat back
in this position (for removal) by Fold the seat back onto the seat
pressing down on it. cushion.
Push control D upwards to release Note: you can lock the seat back
the rear feet. in this position (for removal) by
pressing down on it.
Place the seat in the folded position.
Push the two levers E upwards to
unlock the rear feet.
While driving, attach the retaining Place the seat in the folded position.
strap (contained in the storage
pocket of one of the front seats)
on one side to the carrying han- While driving, attach the retaining
dle G and on the other side, to the strap (contained in the storage
grab handle. pocket of the additional seat) on
one side to the carrying handle G
and on the other side, to the rear
armrest grab handle.
15-03-2004
84
YOUR 307 SW IN DETAIL
Reitting a seat The rear feet lock automatically, as
do the two red levers F.
In the 3rd row, irst remove the loor
ixing point closers using a thin Check that the seat is locked cor-
screwdriver. rectly.
Before positioning the 3rd row seats, Lift the seat back, irst releasing it by
move those of the 2nd row forward. pulling the strap C.
Check that nothing is obstruct- To lock the additional seats, press
ing the loor ixing points thus the two levers E.
preventing correct locking of the
seat feet.
Carry the seat using the carrying
Removing a seat handle G.
Position the front feet in the securing
Fold the corresponding seat. points.
Tilt the two red levers F under the
seat to release the front feet.
Lift it and carry it using the carrying
handle G.
In the 3rd row, position the ixing point
closers to obtain a lat boot loor.
15-03-2004
85
YOUR 307 SW IN DETAIL
GENERAL POINTS RELATING - Remember to fasten the seat belt
TO CHILD SEATS or the child seat harness keep-
ing the slack in relation to the
Although one of PEUGEOT's main child's body to a minimum, even
criteria when designing your vehicle, for short journeys.
the safety of your children also de-
pends on you.
For maximum safety, please follow
these precautions:
- Since 1992, all children under
the age of 10 must travel in ap-
proved child seats* suited to
their weight, on seats itted with a
seat belt or ISOFIX mountings.
- A child weighing less than Special points relating to the
9 kg must travel in the rearwards transportation of children on the
facing position both in the front front passenger seat* ISOFIX MOUNTINGS
and in the rear. PEUGEOT re-
commends that children should Children under the age of 10 must not The two rear side seats of your vehi-
travel in the "rearwards facing" travel in the forwards facing position, cle are itted with ISOFIX mountings.
position up to the age of two. unless the rear seats are already oc- These are two rings located between
cupied by other children or the rear the seat back and the seat cushion.
- Statistically, the safest seats in seats cannot be used (absent or
your vehicle for the transpor- The ISOFIX child seats are itted
folded). In this case, adjust the front with two locks which are secured
tation of children are the rear passenger seat to the intermediate
seats. PEUGEOT recommends easily on these rings.
longitudinal position and leave the
that children travel in the rear passenger air bag armed. Fitting a child seat in a vehicle incor-
even when a "rearwards facing" rectly compromises the child's pro-
child seat is used. The transportation of children in the tection in the event of a collision.
rearwards facing position is permit-
- If a child is travelling on a booster ted. In this position, it is essential to This ISOFIX mounting system guar-
seat, check that the lap sec- disarm the passenger air bag. Other- antees reliable, safe and fast itting of
tion of the seat belt passes over wise, the child would risk being killed the child seat in your vehicle.
the child's thighs correctly. The or seriously injured if the air bag were The ISOFIX child seats approved for
chest section of the seat belt must to inlate. your vehicle are presented on the
be positioned on the child's shoul- next page.
der without touching the neck.
PEUGEOT recommends that you
use a booster seat with a back, it-
ted with a seat belt guide at shoul-
der level.
* According to current legislation in
the country.
15-03-2004
85
YOUR 307 SW IN DETAIL
GENERAL POINTS RELATING - Remember to fasten the seat belt
TO CHILD SEATS or the child seat harness keep-
ing the slack in relation to the
Although one of PEUGEOT's main child's body to a minimum, even
criteria when designing your vehicle, for short journeys.
the safety of your children also de-
pends on you.
For maximum safety, please follow
these precautions:
- Since 1992, all children under
the age of 10 must travel in ap-
proved child seats* suited to
their weight, on seats itted with a
seat belt or ISOFIX mountings.
- A child weighing less than Special points relating to the
9 kg must travel in the rearwards transportation of children on the
facing position both in the front front passenger seat* ISOFIX MOUNTINGS
and in the rear. PEUGEOT re-
commends that children should Children under the age of 10 must not The two rear side seats of your vehi-
travel in the "rearwards facing" travel in the forwards facing position, cle are itted with ISOFIX mountings.
position up to the age of two. unless the rear seats are already oc- These are two rings located between
cupied by other children or the rear the seat back and the seat cushion.
- Statistically, the safest seats in seats cannot be used (absent or
your vehicle for the transpor- The ISOFIX child seats are itted
folded). In this case, adjust the front with two locks which are secured
tation of children are the rear passenger seat to the intermediate
seats. PEUGEOT recommends easily on these rings.
longitudinal position and leave the
that children travel in the rear passenger air bag armed. Fitting a child seat in a vehicle incor-
even when a "rearwards facing" rectly compromises the child's pro-
child seat is used. The transportation of children in the tection in the event of a collision.
rearwards facing position is permit-
- If a child is travelling on a booster ted. In this position, it is essential to This ISOFIX mounting system guar-
seat, check that the lap sec- disarm the passenger air bag. Other- antees reliable, safe and fast itting of
tion of the seat belt passes over wise, the child would risk being killed the child seat in your vehicle.
the child's thighs correctly. The or seriously injured if the air bag were The ISOFIX child seats approved for
chest section of the seat belt must to inlate. your vehicle are presented on the
be positioned on the child's shoul- next page.
der without touching the neck.
PEUGEOT recommends that you
use a booster seat with a back, it-
ted with a seat belt guide at shoul-
der level.
* According to current legislation in
the country.
15-03-2004
86
YOUR 307 SW IN DETAIL
These child seats can be used
on seats which are not itted with
ISOFIX mountings. In this case it
is compulsory to attach them to the
vehicle's seat by means of the three-
point seat belt.
The ISOFIX KIDDY* child seat The ISOFIX RÖMER Duo* child
seat
It can be itted in the "rear facing"
position (when the side seats are The child seat is installed in the
recentred) from birth to 13 kg and in "forwards facing" position only for
the "forwards facing" position from 9 children from 9 to 18 kg. It is secured
to 18 kg. without the upper strap called the
Top Tether.
In the rear, in the "forwards facing"
position, it is imperative that the front For your child's comfort, there are
passenger seat is in the intermedi- three seat body angles: sitting,
ate longitudinal position, seat back reclining and lying.
upright. When the Römer Duo is installed in
In the "rear facing" position, the body the rear, the front seat of the vehicle
of the child seat must be in contact must be adjusted so that the child's
with the back of the corresponding feet do not touch the back of the front
front seat. seat.
The ISOFIX KIDDY seat can also
be installed on a 2nd row side seat
which has been positioned in the 3rd
row. In ths case, the ISOFIX KIDDY
seat must be in the "rear facing"
position, the body supported on the
seat back of the corresponding 2nd * You can only it ISOFIX child seats
row seat. approved by PEUGEOT on your
vehicle's ISOFIX mountings.
15-03-2004
87
YOUR 307 SW IN DETAIL
CHILD SEATS L2 - "Römer Baby-Safe": installed
RECOMMENDED BY in the rear-facing position using a
PEUGEOT three-point seat belt. The deep and
strengthened shell is designed to
In addition to the ISOFIX child seats, guarantee the child optimum protec-
PEUGEOT offers a complete range tion in the event of a side collision.
of child seats which are secured When one of these seats is installed
using the seat belt: in the front, it is compulsory to disarm
the passenger air bag and the vehi-
cle's seat must be adjusted to the
intermediate longitudinal position.
Group 2: from 15 to 25 kg
L4 - "Römer Vario'': installed using a
two or three-point seat belt.
Group 1: from 9 to 18 kg
L3 - "Römer Prince": installed using a
two or three-point seat belt. Groups 2 and 3: from 15 to 36 kg
For the safety of your child, it is L5 - "Recaro Start'': installed using a
imperative that the restraining cushion three-point seat belt.
is used. The height and width at the shoul-
Group 0+: from birth to 13 kg ders and length of the seat cushion
must be adjusted according to the
L1 - "Britax Babysure": installed age and build of your child.
in the rear-facing position using a
three-point seat belt.
15-03-2004
88
YOUR 307 SW IN DETAIL
For the safety of young children (from
9 to 18 kg), PEUGEOT recommends Never leave one or more
use of the restraining cushion. children alone and unsu-
pervised in a vehicle.
Never leave a child or
an animal in a vehicle which is
Recommendations exposed to the sun and has the
For optimum installation of a for- windows closed.
wards facing child seat, check that To protect your young children
the back of the child seat is resting from the sun, it blinds on the rear
against the back of the vehicle's seat windows.
correctly and that the head restraint
does not cause any discomfort.
L6 - "Klippan Optima": installed in the
rear using a three-point seat belt. If it is necessary to remove the
head restraint, as in the case of the
From the age of 6 years (approxi- "RECARO Start", "KLIPPAN Optima"
mately 22 kg), the booster is used and "KIDDY Life" child seats (over
on its own. 6 years of age), ensure that the head
restraint is securely stored or at-
tached so that it cannot act as a pro-
jectile in the event of sharp braking.
Never leave the keys within reach
of children inside the vehicle.
Observe strictly the recommenda-
Disarm the passenger air bag tions for assembling and securing
when installing a "rearwards the child seat as shown in the
facing" child seat on the front child seat instructions.
passenger seat. Otherwise, the To prevent the doors from opening
child would risk being seriously accidentally, use the child lock*.
injured or killed were the air bag Also, do not open the rear win-
to inlate. dows more than a third*.
Groups 1, 2 and 3: from 9 to 36 kg
L7 - "Kiddy Life": installed in the rear
using a three-point seat belt.
The height and width at the shoulders
and the length of the seat cushion
must be adjusted according to the
age and build of your child.
* According to model.
15-03-2004
89
YOUR 307 SW IN DETAIL
Weight of the child and indicative age
Side
Seat off centre and recentred U U U U
2nd
row
Centre U U U U
Centre seat
Side
Additional seat L1, L2 L3, L7 L4, L5, L6, L7 L5, L6, L7
3rd Side U U U U
row 2nd row side seat
Side U U U U
2nd row centre seat
SUMMARY TABLE FOR U: seat suitable for the installation Brand Model Approval N°
FITTING CHILD SEATS of a child seat secured using the L1: BRITAX Babysure E11 0344117
seat belt and "universally" approved. L2: RÖMER Baby-Safe E1 03301146
In accordance with the European "Rear facing" child seats and "for-
regulation (Directive 2000/3), this wards facing" child seats. L3: RÖMER Prince E1 03301058
table indicates the options for the L4: RÖMER Vario E1 03301120
U (R): seat suitable for the installa-
installation of child seats secured tion of a universal "rear facing" child L5: RECARO Start E1 03301108
using the seat belt and universally seat and a universal "forwards fac- L6: KLIPPAN Optima E17 030007
approved (child seats which can be ing" child seat. The vehicle seat must
installed in all vehicles using the seat L7: KIDDY Life E1 03301135
be adjusted to the highest position. (a) Group 0: from birth to 10 kg.
belt), depending on the weight of the
child and the seat in the vehicle: L-: only the child seats indicated can (b) The rules for transporting chil-
be installed on the seat concerned dren in the front passenger seat are
(according to destination). speciic to each country. Consult the
current legislation in your country.
15-03-2004
90
YOUR 307 SW IN DETAIL
15-03-2004
91
YOUR 307 SW IN DETAIL
To be effective, a seat
belt must be tightened as
close to the body as pos-
sible.
If the seats are itted with arm-
rests, the lap section of the seat
belt must always pass under the
armrest.
Do not use the strap guide when a
child seat is itted.
Do not invert the seat belt buck-
les as they will not carry out their
function fully.
Depending on the nature and the
seriousness of the impact, the
pre-tensioners may be triggered
before and independently of trig-
gering of the air bags.
In all cases, the air bag warning
light comes on.
2nd row rear centre seat belt 3rd row rear seat belts Following a collision, have the
system checked by a PEUGEOT
The 2nd row rear centre seat has a The 3rd row rear seats are itted dealer.
three-point inertia reel seat belt in- with two three-point inertia reel seat
corporated in the centre of the roof. belts.
Pass buckle A, then buckle B, into To put on the seat belt, insert buckle
the strap guide working from the in- C then buckle D into their respective
side to the outside of the seat. stalks.
Insert buckle A into its stalk (right), To remove the seat belt, proceed in
then buckle B into its stalk (left). the reverse order, then move buckle
To remove the seat belt, proceed in D to the location E provided.
the reverse order, then move buckle
B to the magnet of the roof ixing
point.
15-03-2004
92
YOUR 307 SW IN DETAIL
SEAT MODULARITY AND DIFFERENT CONFIGURATIONS
The design of your vehicle and of its seats offers multiple Examples of varied arrangements combining comfort
seat conigurations. and practicality:
There are side seats which can be installed in the 2nd or 5 seats
3rd row, on the right or on the left.
Once the centre seat has been removed from the 2nd row,
you can recentre the side seats for more comfort.
15-03-2004
93
YOUR 307 SW IN DETAIL
5 seats with centre seat in the 3rd row 4 seats with side seat in the 3rd row
15-03-2004
94
YOUR 307 SW IN DETAIL
6 seats with an additional seat and the centre seat in 7 seats with two additional seats
the 3rd row
5 seats with table position and one additional seat 5 seats with two folded additional seats
15-03-2004
95
YOUR 307 SW IN DETAIL
THE KEYS The remote control Unlocking
The keys allow you to switch on the Locking Press button B to unlock the vehicle.
ignition and to independently operate This is conirmed by rapid lashing of
the locks on the front doors, the fuel Press button A to lock the vehicle.
the direction indicators.
iller cap and the passenger air bag This is conirmed by ixed lighting of
disarming switch. the direction indicators for approxi-
mately two seconds. Note: if the vehicle is locked and
unlocking is activated inadvertently
Central locking Note: a long press on button A, in without the doors being opened with-
addition to locking, automatically in 30 seconds, the vehicle will lock
From the driver's door, the keys al- closes the windows.
low you to lock, deadlock or unlock itself automatically.
the doors and tailgate, as well as fold
back the exterior mirrors. Vehicles itted with deadlocking
If one of the doors or the boot is Warning: deadlocking renders the
open, the central locking does not internal and external door locking
work; an audible signal indicates this controls inoperative.
when locking by remote control. One press on button A deadlocks
The remote control performs the the vehicle. Locating your vehicle
same functions at a distance. This is conirmed by ixed lighting of To locate your vehicle, if you have
the direction indicators for approxi- locked it, in a car park:
mately two seconds. F press button A, the courtesy lights
Note: a long press on button A, in come on and the direction indica-
addition to deadlocking, automati- tors lash for a few seconds.
cally closes the windows.
A second press on button A within
ive seconds of deadlocking changes
this to normal locking.
This is conirmed by ixed lighting of
the direction indicators for approxi-
mately two seconds.
15-03-2004
96
YOUR 307 SW IN DETAIL
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for starting to be
possible. Changing the battery of the
Confidential card remote control
If the system does not function The conidential card contains the
correctly, the central locking button Warning that the battery is lat is given
identiication code necessary for any by an audible signal accompanied
indicator light, situated in the centre work carried out by a PEUGEOT
of the fascia, lashes rapidly when the by the message ''Remote control
dealer on the electronic immobiliser battery low'' on the multifunction
ignition is switched on (2nd notch). In system. This code is hidden by a
this case your vehicle will not start. display.
ilm, which should be removed only To replace the battery, remove the
Contact a PEUGEOT dealer as soon if necessary.
as possible. screw then unclip the casing using
Keep your card in a safe place, a coin at the ring (CR 2016/3 volt
never inside the vehicle. battery).
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv- Programming the remote
er's door, if the key has been left in control
the ignition.
F Switch off the ignition.
F Switch the ignition on again.
F Press button A immediately for a
few seconds.
F Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
15-03-2004
97
YOUR 307 SW IN DETAIL
Make a careful note of the When purchasing a second-hand
number on each key. The vehicle:
key number is coded on the - ensure that you are given the
label attached to the key. conidential card;
If the keys are lost, your PEUGEOT - have the key codes memorised
dealer can rapidly supply you with by a PEUGEOT dealer, to ensure
new keys. that the keys in your possession
are the only ones which can start
The high frequency remote control the vehicle.
is a sensitive system; do not
operate it while it is in your pocket Do not make any modiications to
as there is a possibility that it may the electronic engine immobiliser
unlock your vehicle, without you system.
being aware of it.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off,
except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Driving with the doors locked may
make access to the passenger
compartment by the emergency
services more dificult in an
emergency.
As a safety precaution (with children
on board), remove the ignition key
when you leave the vehicle, even
for a short time.
Do not repeatedly press the button
of your remote control out of range
of your vehicle. You run the risk of
stopping it from working and the
remote control would have to be
reprogrammed.
15-03-2004
96
YOUR 307 SW IN DETAIL
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for starting to be
possible. Changing the battery of the
Confidential card remote control
If the system does not function The conidential card contains the
correctly, the central locking button Warning that the battery is lat is given
identiication code necessary for any by an audible signal accompanied
indicator light, situated in the centre work carried out by a PEUGEOT
of the fascia, lashes rapidly when the by the message ''Remote control
dealer on the electronic immobiliser battery low'' on the multifunction
ignition is switched on (2nd notch). In system. This code is hidden by a
this case your vehicle will not start. display.
ilm, which should be removed only To replace the battery, remove the
Contact a PEUGEOT dealer as soon if necessary.
as possible. screw then unclip the casing using
Keep your card in a safe place, a coin at the ring (CR 2016/3 volt
never inside the vehicle. battery).
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Key in ignition
A buzzer sounds on opening the driv- Programming the remote
er's door, if the key has been left in control
the ignition.
F Switch off the ignition.
F Switch the ignition on again.
F Press button A immediately for a
few seconds.
F Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
15-03-2004
97
YOUR 307 SW IN DETAIL
Make a careful note of the When purchasing a second-hand
number on each key. The vehicle:
key number is coded on the - ensure that you are given the
label attached to the key. conidential card;
If the keys are lost, your PEUGEOT - have the key codes memorised
dealer can rapidly supply you with by a PEUGEOT dealer, to ensure
new keys. that the keys in your possession
are the only ones which can start
The high frequency remote control the vehicle.
is a sensitive system; do not
operate it while it is in your pocket Do not make any modiications to
as there is a possibility that it may the electronic engine immobiliser
unlock your vehicle, without you system.
being aware of it.
The remote control does not operate
when the key is in the ignition, even
when the ignition is switched off,
except for reprogramming.
Do not operate the deadlocking
function if there is anyone inside
the vehicle.
Driving with the doors locked may
make access to the passenger
compartment by the emergency
services more dificult in an
emergency.
As a safety precaution (with children
on board), remove the ignition key
when you leave the vehicle, even
for a short time.
Do not repeatedly press the button
of your remote control out of range
of your vehicle. You run the risk of
stopping it from working and the
remote control would have to be
reprogrammed.
15-03-2004
98
YOUR 307 SW IN DETAIL
When the alarm is triggered, the si- F Set the alarm by locking or dead-
ren sounds and the direction indica- locking using the remote control
tor lights lash for thirty seconds. (button A indicator light lashes
After triggering, the alarm remains once a second).
set. Note: when the alarm is set but the
Warning: if the alarm has been trig- remote control does not operate:
gered ten times in succession, on the F Unlock the doors with the key and
eleventh time it becomes inactive. open the door. The alarm is trig-
gered.
Note: if button A indicator light
lashes rapidly, the alarm has been F Switch on the ignition. The alarm is
triggered while you were away from disarmed.
THE ALARM
your vehicle.
This provides two types of protection: Incorrect operation
- exterior protection: it sounds if Disarming When the ignition is switched on, if
a door, the boot or the bonnet is button A lights for ten seconds, there
opened. Unlock the vehicle with the remote
control key (button A indicator light is a fault in the siren connection.
- interior protection: it sounds if goes out). Contact a PEUGEOT dealer to have
the volume inside the passenger the system checked.
compartment changes (breaking of Note: if the alarm has been triggered
a window or a movement inside the while you were away from your vehi-
vehicle). cle, the rapid lashing of the indicator Automatic activation*
light will stop when you switch on the The alarm is activated automatically
Setting the alarm ignition. two minutes after the last closure of a
door or the boot.
F Switch off the ignition and get out To set the alarm with exterior
of the vehicle. In order to avoid accidental triggering
protection only of the alarm when a door or the boot
F Set the alarm, by locking or dead-
locking using the remote control If, while you are away from the ve- is opened, it is essential to irst press
(button A indicator light lashes hicle, you wish to leave a window the unlocking button on the remote
once per second). partially open or a pet inside the control.
vehicle, you should choose exterior
Note: if you wish to lock your vehicle protection only.
without setting the alarm, use the
door lock. F Switch off the ignition,
F In the next ten seconds, press
button A until the indicator light is
on continuously,
F Get out of the vehicle,
* According to destination.
15-03-2004
99
YOUR 307 SW IN DETAIL
THE DOORS
15-03-2004
101
YOUR 307 SW IN DETAIL
15-03-2004
102
YOUR 307 SW IN DETAIL
Safety auto-reverse
At the end of its travel, if the shutter
encounters an obstacle to closing, it
stops and moves back slightly.
Notes
If the shutter's power supply is cut
off, while it is moving or immediately
after it has stopped, you must reini-
tialise the safety auto-reverse:
- press section B of the switch until
the shutter is completely closed
PANORAMIC ROOF (closing in stages of a few centi-
Your vehicle is itted with a tinted metres).
glass panoramic roof which in-
creases the light and visibility in the In the event of unwanted opening of
passenger compartment. Its electric the shutter on closing, and immedi-
concealing shutter improves tem- ately after the shutter has stopped:
perature conditions.
- press section A of the switch until
To open: press part A of the switch. the shutter is fully open,
To close: press part B of the switch. - release section A and immediately
afterwards press section B of the
Manually: press the switch without switch until the shutter is fully
going past the point of resistance; closed (closing in stages of a few
the shutter stops as soon as the centimetres).
switch is released.
The safety auto-reverse function is
Automatically: press the switch not active during these operations.
beyond the point of resistance;
one press fully opens or closes the
shutter. Press the switch again to
stop the shutter.
15-03-2004
103
YOUR 307 SW IN DETAIL
The engine must be switched off
when illing with fuel.
F Open the fuel iller lap.
F Insert the key then turn it to the
left.
F Remove the cap and hang it on the
hook located on the inside of the
lap.
A label afixed to the inside of the fuel
iller lap indicates which type of fuel
to use.
When you ill your tank, do not con-
tinue after the third cut-off of the
pump. This could cause your vehicle
to malfunction.
OPENING THE BONNET FILLING WITH FUEL The capacity of the tank is ap-
proximately 60 litres.
From inside: push the handle on the Low fuel level F After illing the tank, lock the cap
left-hand side under the fascia. and close the fuel iller lap.
From outside: lift the catch and
raise the bonnet. When the minimum
fuel level in the tank is
Bonnet strut reached, this warning
light comes on.
Secure the strut to hold the bonnet
open. You can still drive
approximately 30 miles (50 km).
Before closing the bonnet, replace
the strut in its housing. Flashing of the warning light indicates
a malfunction of the fuel gauge.
Contact a PEUGEOT dealer.
To close
Lower the bonnet and release it at
the end of its travel. Check that the
bonnet is properly locked.
15-03-2004
104
YOUR 307 SW IN DETAIL
Dipped / Main beam change Vehicles itted with front fog
lamps and a rear fog lamp (ring C)
Pull the stalk towards you.
Note: with the ignition off, when the
driver's door is opened, a buzzer Front fog lamps (irst rotation
sounds if you have left your lights of the ring forwards)
on.
Front fog lamps and rear fog lamp The front fog lamps operate with
Rotate the ring forwards to switch on the side lights and the dipped head-
and backwards to switch off. The sta- lamps.
tus is conirmed by the indicator light When the main beam headlamps are
on the instrument panel. switched on, the front fog lamps are
switched off. They are switched on
THE LIGHTS STALK again when the main beam head-
lamps are switched off.
Front and rear lights
Selection is by turning ring A. Vehicles itted with a rear fog Front and rear fog
lamp (ring B) lamps (2nd rotation of
the ring forwards).
Rear fog lamp Note: to switch off
the rear fog lamp and the front fog
Lights off lamps, turn the ring backwards twice
in succession.
This only operates with the dipped /
main beam headlamps. Note: when the lights are switched
Side lights Note: when the lights are switched off automatically or when the dipped
off automatically, the rear fog lamp headlamps are switched off manu-
and the dipped headlamps will re- ally, the front fog lamps, the rear fog
main on (turn the ring backwards lamp and the side lights will remain
Dipped / main beam to switch off the rear fog lamp. The on (turn the ring backwards to switch
headlamps dipped headlamps and side lights will off the front fog lamps. The side lights
then be switched off). will then be switched off).
Automatic switching on
of lights
15-03-2004
105
YOUR 307 SW IN DETAIL
"Follow me home" lighting AUTOMATIC SWITCHING ON Operating check
In poor light or at night, if you leave OF LIGHTS
your vehicle, the side lights and Activation
The side lights and dipped beam
dipped headlamps can be left on for headlamps switch on automati- The activated function is accompa-
approximately one minute. cally if the light is poor and when the nied by an audible signal and a mes-
To do this: windscreen wipers operate continu- sage on the multifunction display.
- place the key in the STOP position, ously and switch off when the light
becomes bright enough or the wind- Disarming
- place the lights stalk in the 0 screen wipers are switched off.
position, The disarmed function is accompa-
In foggy weather or in snow, the
- lash the headlamps, brightness sensor can detect nied by an audible signal.
- get out of the vehicle and lock it. suficient light, the lights will not When the driver uses the manual
come on automatically. lighting controls, the function is tem-
porarily disarmed.
This function is active when the vehi- If the brightness sensor does not
cle is supplied to the customer. function correctly, the lights come
To disarm or activate the function: on accompanied by an audible signal
In good or rainy weather, - Place the key in the accessories and a message on the multifunction
both day and night, the position (1st notch), display.
front fog lamps and the - Place the lights stalk in the AUTO/ Contact a PEUGEOT dealer.
rear fog lamp are dazzling 0 position,
and are prohibited. - Press the end of the lights stalk for
Do not forget to switch them off more than four seconds.
when they are no longer needed.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
Direction indicators (lashers) on of the lights.
Left: downwards.
Right: upwards.
15-03-2004
106
YOUR 307 SW IN DETAIL
The command must be reactivated
each time the ignition is switched
back on:
- move the stalk to any position,
- then move it back to the required
position.
15-03-2004
107
YOUR 307 SW IN DETAIL
Automatic windscreen wipers Rear windscreen wiper
In the AUTO position, the wind- Turn ring A to the irst notch
screen wipers operate automatically for intermittent wiping.
and adapt their speed to the inten-
sity of the rainfall.
Operating check
Activation
Rear windscreen wash
When the function is activated, the
message "Automatic wiping ac- Turn ring A past the irst
tive" appears on the multi-function notch; the windscreen wash
display. then the windscreen wiper
operate for a ixed period.
Disarming
In the event of malfunction, the
driver is informed by an audible sig-
nal and the message "Auto wiper
fault" on the multi-function display.
In the AUTO position, the wind-
screen wiper will operate in intermit-
tent mode.
Contact a PEUGEOT dealer to have
the system checked.
15-03-2004
108
YOUR 307 SW IN DETAIL
TRIP COMPUTER Colour screen DT
15-03-2004
109
YOUR 307 SW IN DETAIL
Range Distance remaining to be
This shows the distance that can still
travelled
be covered with the fuel remaining in This is the distance remaining to the
the tank. destination. It can either be calcu-
Note: this igure may increase if lated by the navigation if guidance
there is a change in the style of driv- is activated, or entered by the user,
ing or the road surface, producing a minus the distance covered since the
signiicant drop in current consump- distance was entered.
tion. Note: if digits are missing, dashes
When the range is less than 20 miles are displayed in their place.
(30 km), three segments are dis-
played. After illing with fuel, the
range is displayed when it exceeds Average speed
62 miles (100 km). This is the average speed calculated
If horizontal segments are displayed since the computer was last set to
for long periods instead of digits, zero (with the ignition on).
contact a PEUGEOT dealer. The routes
The warning log The routes "1" and ''2'' are independ-
Current consumption This summarises the active warning
ent but have identical application.
This is the average quantity of fuel messages by displaying them on the Route "1" for example allows you
consumed during the last few sec- multi-function display. to make daily calculations and route
onds. "2" monthly calculations.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
This is the average fuel consump-
tion since the computer was last set
to zero.
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
15-03-2004
110
YOUR 307 SW IN DETAIL
Specific features of the On-board computer coniguration
monochrome screen CT and This function allows the distance to
the colour screen DT the destination to be input (when
General menu guidance is not activated; otherwise
this information is given by the navi-
Press the "MENU" button to access gation system) and also changing of
the general menu. the units of measurement (°C or °F,
Select the icon ''On-board com- km and litres or miles and gallons).
puter'' using the dial, then validate
to access the ''On-board computer'' Distance to destination
menu. When guidance is not activated, this
The ''On-board computer'' menu of- enables an approximate value to be
fers various choices: entered to make all the on-board
- On-board computer coniguration, computer calculations possible.
- Warning log.
15-03-2004
111
YOUR 307 SW IN DETAIL
Automatic operation: When the button is raised, disarming
is active. When the button is lowered,
Press or pull switch fully: the window disarming is deactivated.
opens or closes completely when
the switch is released. Pressing the
switch again stops the movement of REINITIALISATION OF THE
the window. WINDOWS
Note: when one of the doors is
opened or approximately 45 seconds Following reconnection of the battery
following removal of the ignition key, or in the event of a malfunction, re-
none of the windows can be opened lease the switch and pull it again until
or closed. The ignition must be it closes completely. Hold the switch
switched on again to open or close for approximately one second after
the windows. closing.
The safety auto-reverse function
Safety auto-reverse is not active during these opera-
ELECTRIC WINDOWS tions.
1 - Driver's electric window When the window rises and meets
switch. an obstacle, it stops and partially
lowers again.
2 - Passenger's electric window Always remove the key
Note: from the ignition when
switch.
In the event of unwanted opening of leaving the vehicle, even
3 - Rear right electric window the window on closing (for example for a short time.
switch. in the presence of frost), press the In the event of contact during op-
4 - Rear left electric window switch until it opens completely, then eration of the windows, you must
switch. pull it immediately until it closes. reverse the movement of the win-
Continue to hold the switch for ap- dow. To do this, press the switch
5 - Disarming of the rear electric proximately one second after the
window switches (child lock). concerned.
window has closed.
When the driver operates the pas-
You have two options: The safety auto-reverse function senger electric window switches,
is not active during these opera- he must ensure that no one is
Manual operation: tions. preventing correct closing of the
Disarming the rear window windows.
Press or pull switch gently. The win-
dow stops as soon as the switch is controls The driver must ensure that the
released. passengers use the electric win-
For the safety of your children, press dows correctly.
switch 5 to prevent operation of the
rear windows irrespective of their Be aware of children when operat-
position. ing the windows.
15-03-2004
103
YOUR 307 SW IN DETAIL
The engine must be switched off
when illing with fuel.
F Open the fuel iller lap.
F Insert the key then turn it to the
left.
F Remove the cap and hang it on the
hook located on the inside of the
lap.
A label afixed to the inside of the fuel
iller lap indicates which type of fuel
to use.
When you ill your tank, do not con-
tinue after the third cut-off of the
pump. This could cause your vehicle
to malfunction.
OPENING THE BONNET FILLING WITH FUEL The capacity of the tank is ap-
proximately 60 litres.
From inside: push the handle on the Low fuel level F After illing the tank, lock the cap
left-hand side under the fascia. and close the fuel iller lap.
From outside: lift the catch and
raise the bonnet. When the minimum
fuel level in the tank is
Bonnet strut reached, this warning
light comes on.
Secure the strut to hold the bonnet
open. You can still drive
approximately 30 miles (50 km).
Before closing the bonnet, replace
the strut in its housing. Flashing of the warning light indicates
a malfunction of the fuel gauge.
Contact a PEUGEOT dealer.
To close
Lower the bonnet and release it at
the end of its travel. Check that the
bonnet is properly locked.
15-03-2004
104
YOUR 307 SW IN DETAIL
Dipped / Main beam change Vehicles itted with front fog
lamps and a rear fog lamp (ring C)
Pull the stalk towards you.
Note: with the ignition off, when the
driver's door is opened, a buzzer Front fog lamps (irst rotation
sounds if you have left your lights of the ring forwards)
on.
Front fog lamps and rear fog lamp The front fog lamps operate with
Rotate the ring forwards to switch on the side lights and the dipped head-
and backwards to switch off. The sta- lamps.
tus is conirmed by the indicator light When the main beam headlamps are
on the instrument panel. switched on, the front fog lamps are
switched off. They are switched on
THE LIGHTS STALK again when the main beam head-
lamps are switched off.
Front and rear lights
Selection is by turning ring A. Vehicles itted with a rear fog Front and rear fog
lamp (ring B) lamps (2nd rotation of
the ring forwards).
Rear fog lamp Note: to switch off
the rear fog lamp and the front fog
Lights off lamps, turn the ring backwards twice
in succession.
This only operates with the dipped /
main beam headlamps. Note: when the lights are switched
Side lights Note: when the lights are switched off automatically or when the dipped
off automatically, the rear fog lamp headlamps are switched off manu-
and the dipped headlamps will re- ally, the front fog lamps, the rear fog
main on (turn the ring backwards lamp and the side lights will remain
Dipped / main beam to switch off the rear fog lamp. The on (turn the ring backwards to switch
headlamps dipped headlamps and side lights will off the front fog lamps. The side lights
then be switched off). will then be switched off).
Automatic switching on
of lights
15-03-2004
105
YOUR 307 SW IN DETAIL
"Follow me home" lighting AUTOMATIC SWITCHING ON Operating check
In poor light or at night, if you leave OF LIGHTS
your vehicle, the side lights and Activation
The side lights and dipped beam
dipped headlamps can be left on for headlamps switch on automati- The activated function is accompa-
approximately one minute. cally if the light is poor and when the nied by an audible signal and a mes-
To do this: windscreen wipers operate continu- sage on the multifunction display.
- place the key in the STOP position, ously and switch off when the light
becomes bright enough or the wind- Disarming
- place the lights stalk in the 0 screen wipers are switched off.
position, The disarmed function is accompa-
In foggy weather or in snow, the
- lash the headlamps, brightness sensor can detect nied by an audible signal.
- get out of the vehicle and lock it. suficient light, the lights will not When the driver uses the manual
come on automatically. lighting controls, the function is tem-
porarily disarmed.
This function is active when the vehi- If the brightness sensor does not
cle is supplied to the customer. function correctly, the lights come
To disarm or activate the function: on accompanied by an audible signal
In good or rainy weather, - Place the key in the accessories and a message on the multifunction
both day and night, the position (1st notch), display.
front fog lamps and the - Place the lights stalk in the AUTO/ Contact a PEUGEOT dealer.
rear fog lamp are dazzling 0 position,
and are prohibited. - Press the end of the lights stalk for
Do not forget to switch them off more than four seconds.
when they are no longer needed.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
Direction indicators (lashers) on of the lights.
Left: downwards.
Right: upwards.
15-03-2004
105
YOUR 307 SW IN DETAIL
"Follow me home" lighting AUTOMATIC SWITCHING ON Operating check
In poor light or at night, if you leave OF LIGHTS
your vehicle, the side lights and Activation
The side lights and dipped beam
dipped headlamps can be left on for headlamps switch on automati- The activated function is accompa-
approximately one minute. cally if the light is poor and when the nied by an audible signal and a mes-
To do this: windscreen wipers operate continu- sage on the multifunction display.
- place the key in the STOP position, ously and switch off when the light
becomes bright enough or the wind- Disarming
- place the lights stalk in the 0 screen wipers are switched off.
position, The disarmed function is accompa-
In foggy weather or in snow, the
- lash the headlamps, brightness sensor can detect nied by an audible signal.
- get out of the vehicle and lock it. suficient light, the lights will not When the driver uses the manual
come on automatically. lighting controls, the function is tem-
porarily disarmed.
This function is active when the vehi- If the brightness sensor does not
cle is supplied to the customer. function correctly, the lights come
To disarm or activate the function: on accompanied by an audible signal
In good or rainy weather, - Place the key in the accessories and a message on the multifunction
both day and night, the position (1st notch), display.
front fog lamps and the - Place the lights stalk in the AUTO/ Contact a PEUGEOT dealer.
rear fog lamp are dazzling 0 position,
and are prohibited. - Press the end of the lights stalk for
Do not forget to switch them off more than four seconds.
when they are no longer needed.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
Direction indicators (lashers) on of the lights.
Left: downwards.
Right: upwards.
15-03-2004
106
YOUR 307 SW IN DETAIL
The command must be reactivated
each time the ignition is switched
back on:
- move the stalk to any position,
- then move it back to the required
position.
15-03-2004
107
YOUR 307 SW IN DETAIL
Automatic windscreen wipers Rear windscreen wiper
In the AUTO position, the wind- Turn ring A to the irst notch
screen wipers operate automatically for intermittent wiping.
and adapt their speed to the inten-
sity of the rainfall.
Operating check
Activation
Rear windscreen wash
When the function is activated, the
message "Automatic wiping ac- Turn ring A past the irst
tive" appears on the multi-function notch; the windscreen wash
display. then the windscreen wiper
operate for a ixed period.
Disarming
In the event of malfunction, the
driver is informed by an audible sig-
nal and the message "Auto wiper
fault" on the multi-function display.
In the AUTO position, the wind-
screen wiper will operate in intermit-
tent mode.
Contact a PEUGEOT dealer to have
the system checked.
15-03-2004
108
YOUR 307 SW IN DETAIL
TRIP COMPUTER Colour screen DT
15-03-2004
109
YOUR 307 SW IN DETAIL
Range Distance remaining to be
This shows the distance that can still
travelled
be covered with the fuel remaining in This is the distance remaining to the
the tank. destination. It can either be calcu-
Note: this igure may increase if lated by the navigation if guidance
there is a change in the style of driv- is activated, or entered by the user,
ing or the road surface, producing a minus the distance covered since the
signiicant drop in current consump- distance was entered.
tion. Note: if digits are missing, dashes
When the range is less than 20 miles are displayed in their place.
(30 km), three segments are dis-
played. After illing with fuel, the
range is displayed when it exceeds Average speed
62 miles (100 km). This is the average speed calculated
If horizontal segments are displayed since the computer was last set to
for long periods instead of digits, zero (with the ignition on).
contact a PEUGEOT dealer. The routes
The warning log The routes "1" and ''2'' are independ-
Current consumption This summarises the active warning
ent but have identical application.
This is the average quantity of fuel messages by displaying them on the Route "1" for example allows you
consumed during the last few sec- multi-function display. to make daily calculations and route
onds. "2" monthly calculations.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
This is the average fuel consump-
tion since the computer was last set
to zero.
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
15-03-2004
108
YOUR 307 SW IN DETAIL
TRIP COMPUTER Colour screen DT
15-03-2004
109
YOUR 307 SW IN DETAIL
Range Distance remaining to be
This shows the distance that can still
travelled
be covered with the fuel remaining in This is the distance remaining to the
the tank. destination. It can either be calcu-
Note: this igure may increase if lated by the navigation if guidance
there is a change in the style of driv- is activated, or entered by the user,
ing or the road surface, producing a minus the distance covered since the
signiicant drop in current consump- distance was entered.
tion. Note: if digits are missing, dashes
When the range is less than 20 miles are displayed in their place.
(30 km), three segments are dis-
played. After illing with fuel, the
range is displayed when it exceeds Average speed
62 miles (100 km). This is the average speed calculated
If horizontal segments are displayed since the computer was last set to
for long periods instead of digits, zero (with the ignition on).
contact a PEUGEOT dealer. The routes
The warning log The routes "1" and ''2'' are independ-
Current consumption This summarises the active warning
ent but have identical application.
This is the average quantity of fuel messages by displaying them on the Route "1" for example allows you
consumed during the last few sec- multi-function display. to make daily calculations and route
onds. "2" monthly calculations.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
This is the average fuel consump-
tion since the computer was last set
to zero.
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
15-03-2004
110
YOUR 307 SW IN DETAIL
Specific features of the On-board computer coniguration
monochrome screen CT and This function allows the distance to
the colour screen DT the destination to be input (when
General menu guidance is not activated; otherwise
this information is given by the navi-
Press the "MENU" button to access gation system) and also changing of
the general menu. the units of measurement (°C or °F,
Select the icon ''On-board com- km and litres or miles and gallons).
puter'' using the dial, then validate
to access the ''On-board computer'' Distance to destination
menu. When guidance is not activated, this
The ''On-board computer'' menu of- enables an approximate value to be
fers various choices: entered to make all the on-board
- On-board computer coniguration, computer calculations possible.
- Warning log.
15-03-2004
111
YOUR 307 SW IN DETAIL
Automatic operation: When the button is raised, disarming
is active. When the button is lowered,
Press or pull switch fully: the window disarming is deactivated.
opens or closes completely when
the switch is released. Pressing the
switch again stops the movement of REINITIALISATION OF THE
the window. WINDOWS
Note: when one of the doors is
opened or approximately 45 seconds Following reconnection of the battery
following removal of the ignition key, or in the event of a malfunction, re-
none of the windows can be opened lease the switch and pull it again until
or closed. The ignition must be it closes completely. Hold the switch
switched on again to open or close for approximately one second after
the windows. closing.
The safety auto-reverse function
Safety auto-reverse is not active during these opera-
ELECTRIC WINDOWS tions.
1 - Driver's electric window When the window rises and meets
switch. an obstacle, it stops and partially
lowers again.
2 - Passenger's electric window Always remove the key
Note: from the ignition when
switch.
In the event of unwanted opening of leaving the vehicle, even
3 - Rear right electric window the window on closing (for example for a short time.
switch. in the presence of frost), press the In the event of contact during op-
4 - Rear left electric window switch until it opens completely, then eration of the windows, you must
switch. pull it immediately until it closes. reverse the movement of the win-
Continue to hold the switch for ap- dow. To do this, press the switch
5 - Disarming of the rear electric proximately one second after the
window switches (child lock). concerned.
window has closed.
When the driver operates the pas-
You have two options: The safety auto-reverse function senger electric window switches,
is not active during these opera- he must ensure that no one is
Manual operation: tions. preventing correct closing of the
Disarming the rear window windows.
Press or pull switch gently. The win-
dow stops as soon as the switch is controls The driver must ensure that the
released. passengers use the electric win-
For the safety of your children, press dows correctly.
switch 5 to prevent operation of the
rear windows irrespective of their Be aware of children when operat-
position. ing the windows.
15-03-2004
112
YOUR 307 SW IN DETAIL
Manual interior mirror
The end of the driver's
mirror is aspheric (outer The interior mirror has two positions:
area indicated by a dotted - day (normal),
line) in order to reduce the
"blind spot". - night (anti-dazzle).
Objects seen in the driver and To change from one to the other,
passenger mirrors are in reality push or pull the lever on the lower
closer than they appear. edge of the mirror.
Therefore, this must be taken
into account in order to correctly
judge the proximity of vehicles
approaching from the rear.
MIRRORS
Electric exterior mirrors
F Slide switch A to the right or to the
left to select the corresponding
mirror.
F Move knob B in all four directions
to adjust.
F Return switch A to the centre
position.
15-03-2004
112
YOUR 307 SW IN DETAIL
Manual interior mirror
The end of the driver's
mirror is aspheric (outer The interior mirror has two positions:
area indicated by a dotted - day (normal),
line) in order to reduce the
"blind spot". - night (anti-dazzle).
Objects seen in the driver and To change from one to the other,
passenger mirrors are in reality push or pull the lever on the lower
closer than they appear. edge of the mirror.
Therefore, this must be taken
into account in order to correctly
judge the proximity of vehicles
approaching from the rear.
MIRRORS
Electric exterior mirrors
F Slide switch A to the right or to the
left to select the corresponding
mirror.
F Move knob B in all four directions
to adjust.
F Return switch A to the centre
position.
15-03-2004
113
YOUR 307 SW IN DETAIL
HORN
Press one of the three spokes.
* According to destination.
15-03-2004
115
YOUR 307 SW IN DETAIL
COURTESY LIGHTS With the key in the accessories posi- F Pressing switch 1 turns on the
tion (1st notch) or with the ignition on, front and rear courtesy lights for a
1 - Front courtesy light operate the relevant switch. duration of ten minutes.
The front and rear courtesy lights F Pressing switch 3 or 4 turns on the
2 - Front map reading lights come on when the ignition key is reading light concerned or the rear
3 - 2nd row rear reading lights removed, on unlocking the vehicle or courtesy light for a duration of ten
on opening one of the doors. minutes.
4 - 3rd row rear courtesy light
They gradually go off after the igni-
tion has been switched on or the Note: The courtesy lights can be
vehicle is locked. deactivated by pressing switch 1 for
In addition, when the vehicle is mov- more than three seconds. A short
ing, the front and rear courtesy lights press on switch 1 switches the front
lash if a door or the tailgate is not courtesy light on and off. The map
closed properly. reading lights are not affected by this
and may be switched on.
15-03-2004
116
YOUR 307 SW IN DETAIL
15-03-2004
117
YOUR 307 SW IN DETAIL
INTERIOR LAYOUT
1. Glove box
3. Storage
To open the glove box, lift the handle.
The glove box lights when the lid is
opened.
4. 12 volt accessories socket
It contains a ventilation nozzle that
can be closed, distributing the same This is a lighter type socket, itted
conditioned air as the vents of the with a cap. It is supplied with current
passenger compartment, and three from the accessories position (1st
sockets for connecting video equip- notch).
ment.
The layout allows storage of a water 5. Door tray
bottle, a pen, the vehicle handbook,
a pair of spectacles, tokens etc.
6. Storage / Can holder
2. Front ashtray
Pull the lid to open the ashtray. 7. Waste container
To empty it after opening, press the To empty, open it fully (past the point
tab and extract the ashtray. of resistance) then pull on the recep-
tacle to remove it.
To reit, lock it in place on the cover.
15-03-2004
118
YOUR 307 SW IN DETAIL
15-03-2004
119
YOUR 307 SW IN DETAIL
BOOT LAYOUT 4. Rear armrests with grab Note: the roller has two hooks for
handle securing the luggage retaining net
depending on where it is installed.
1. Grab handles and coat hooks
5. Storage nets
7. Luggage retaining net
2. High load retaining net One of them contains the luggage
retaining net. Secure the net's seven hooks in the
fastenings stowing rings and the fastenings on
The high load retaining net can be the loor.
itted in the 2nd or 3rd row. 6. Load space cover
Open the covers of the correspond- 8. Luggage retaining net
ing upper fastenings. To install it: fastenings ("hammock"
Fit the ends of the metal bar in these version) in the tailgate
- position one end of the cover roller
fastenings. in the 2nd row, Fold the net in two.
Secure the two opaque material - compress the opposite end of the Secure the two centre hooks in the
strap hooks in the stowing rings on roller and position it, stowing rings on the loor.
the loor. - release it to allow it to engage, Secure the net's remaining four
The rings are located directly below - unroll the cover as far as the boot hooks on the boot pillars.
the corresponding upper fastenings. pillars,
Pull the two straps taut. - insert the cover guides in the rails
Secure the two hooks on the elastic in the pillars.
parts of the opaque material in these
rings. To remove it:
Note: the net must be positioned so - remove the cover guides from the
that the label can be seen from the pillar rails,
boot. This ensures that the central
seat belt is routed correctly. - return the cover into its roller,
- compress it and remove it from its
support at the 2nd row.
3. 12 V Socket for accessories
This is a 12 volt socket (lighter type), To store it, pull it back and place it
installed on the load space cover left with the two storage nets, already
support. lowered.
It is supplied with the ignition off.
Luggage retaining net, "folded" Luggage retaining net, "hammock" High load retaining net in the
version version, in the tailgate 2nd row
Luggage retaining net, "L" version Luggage retaining net, "hammock" Load space cover stored with the
version at the roller two storage nets
15-03-2004
121
YOUR 307 SW IN DETAIL
"PORSCHE TIPTRONIC Park: to immobilise the vehicle or Moving off
SYSTEM" AUTOMATIC start the engine, with the handbrake With the engine running, to move off
GEARBOX on or off. from position P:
The four speed automatic gearbox Reverse: to reverse (select this F it is essential to press the brake
offers a choice between the comfort function with the vehicle stationary, pedal to exit position P,
of integral automatic operation, en- engine at idle). F select function R, D or M, then
hanced by a sport and a snow pro- gradually release the pressure
gramme, or manual gear changing. Neutral: to start the engine and to on the brake pedal; the vehicle
park, with the handbrake on. moves off immediately.
Note: if function N is engaged inad- You can also move off from position
Gear selection gate vertently while driving, allow the en- N:
gine to return to idle before engaging F release the handbrake, with your
F Move the lever in the gate to function D to accelerate. foot on the brake,
select a position.
The indicator light for the selection Drive: for driving in automatic mode. F select function R, D or M, then
is displayed on the instrument panel gradually release the pressure
display. Manual: to select the gears. on the brake pedal; the vehicle
moves off immediately.
S: sport programme.
T: snow programme. WARNING
When the engine is at idle, brakes
not applied, if function R, D or
Starting the engine M is selected the vehicle moves
F with the handbrake applied, select even without the accelerator being
position P or N in the gate, pressed.
F turn the ignition key to the Starting For this reason, do not leave children
position. unsupervised inside the vehicle,
with the engine running.
When maintenance operations need
to be carried out with the engine
running, apply the handbrake and
select position P.
15-03-2004
122
YOUR 307 SW IN DETAIL
Automatic operation If you take your foot off the accel- Manual operation
erator suddenly, the gearbox will not
Automatic changing of the four change to a higher gear for reasons Manual changing of the four gears:
gears: of safety. F select function M in the gate,
F select function D in the gate. F push the lever to the + sign to
The gearbox always selects the most Sport and snow programmes change to a higher gear,
suitable gear according to the follow- F pull the lever to the - sign to
ing parameters: In addition to the auto-adaptive pro-
gramme, there are two special pro- change to a lower gear.
- the style of driving, grammes. You can change from position D
- the road proile, The programme is displayed on the (driving in automatic mode) to posi-
- the vehicle load. instrument panel screen. tion M (driving in manual mode) at
The gearbox is then operating in any time.
auto-adaptive mode, without any ac- Sport programme Notes
tion on your part.
F Press button S once the vehicle It is only possible to change from one
WARNING has been started and function D gear to another if the vehicle speed
selected. and engine speed permit. If they do
Never select function N when the not, the vehicle will operate tempo-
vehicle is moving. The gearbox automatically favours rarily in automatic mode.
sporty driving and more dynamic ac-
Never select functions P or R unless celeration. When the vehicle is stationary or
the vehicle is stationary. moving very slowly, the gearbox au-
Never change between functions to tomatically selects gear M1.
Snow programme
optimise braking on a slippery sur- Programme S (sport) and T (snow)
face. This programme improves starting do not operate in manual mode.
Notes and drive when traction is poor.
For immediate maximum accelera- F Press button T once the vehicle
tion without touching the gear lever, has been started and function D
press the accelerator pedal down as selected.
far as it will go (kick down). The gear- The gearbox adapts to driving on
box will automatically change down slippery roads.
or maintain the gear selected until Note: you can return to the auto-
maximum engine speed is reached. adaptive programme at any time.
When braking, the gearbox will au- F Press button S or T again to
tomatically change down in order to switch off the programme you are
provide eficient engine braking. in.
15-03-2004
123
YOUR 307 SW IN DETAIL
Operating abnormality HANDBRAKE
Any operating abnormality is indi- Applying
cated by an audible signal, accom- Pull the handbrake to immobilise
panied by the message "Automatic your vehicle.
gear fault" on the multi-function
display, "-" and lashing of the Sport Warning: when parking on a slope,
and Snow warning lights on the in- direct your wheels towards the pave-
strument panel. ment and pull the handbrake.
In this situation the gearbox oper- Releasing
ates in downgrade mode (locked in
3rd gear). You may feel a substantial Pull on the handle and press the but-
knock when changing from P to R ton to release the handbrake.
and from N to R (this will not cause
any damage to the gearbox).
Do not exceed 60 mph (100 km/h),
keeping within the limit of local speed
restrictions.
Contact a PEUGEOT dealer as soon
as possible. Illumination of this warning
light and of the STOP warn-
ing light, accompanied by
an audible signal (while the
vehicle is being driven) and
the message "handbrake on" on
the multi-function display, indicates
that the handbrake is still on or has
not been properly released.
15-03-2004
123
YOUR 307 SW IN DETAIL
Operating abnormality HANDBRAKE
Any operating abnormality is indi- Applying
cated by an audible signal, accom- Pull the handbrake to immobilise
panied by the message "Automatic your vehicle.
gear fault" on the multi-function
display, "-" and lashing of the Sport Warning: when parking on a slope,
and Snow warning lights on the in- direct your wheels towards the pave-
strument panel. ment and pull the handbrake.
In this situation the gearbox oper- Releasing
ates in downgrade mode (locked in
3rd gear). You may feel a substantial Pull on the handle and press the but-
knock when changing from P to R ton to release the handbrake.
and from N to R (this will not cause
any damage to the gearbox).
Do not exceed 60 mph (100 km/h),
keeping within the limit of local speed
restrictions.
Contact a PEUGEOT dealer as soon
as possible. Illumination of this warning
light and of the STOP warn-
ing light, accompanied by
an audible signal (while the
vehicle is being driven) and
the message "handbrake on" on
the multi-function display, indicates
that the handbrake is still on or has
not been properly released.
15-03-2004
124
YOUR 307 SW IN DETAIL
ANTI-LOCK BRAKING Stop immediately. EMERGENCY BRAKING
SYSTEM (ABS) AND THE In both cases, consult a PEUGEOT ASSISTANCE SYSTEM
ELECTRONIC BRAKE FORCE dealer. In an emergency, this system enables
DISTRIBUTION (EBFD) the optimum braking pressure to be
The ABS, in conjunction with the reached more quickly, thus reducing
electronic brake force distribution, the stopping distance.
increases the stability and mano- It is triggered by the speed at which
evrability of your vehicle on braking, Normal operation of the ABS may the brake pedal is activated. The
in particular on poor or slippery road make itself felt by slight vibrations effect of this is a reduction in the re-
surfaces. of the brake pedal. sistance of the pedal and an increase
Note: when changing wheels (tyres In emergency braking, press in braking eficiency.
and rims), make sure that these are very irmly without releasing
approved. the pressure.
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
15-03-2004
125
YOUR 307 SW IN DETAIL
TRACTION CONTROL (ASR) Disarming the ASR/ESP systems Operating check
AND DYNAMIC STABILITY In exceptional conditions (starting a
CONTROL (ESP) vehicle which is bogged down, stuck When a malfunction of the
in snow, on soft ground, ...), it may systems occurs, the switch
These systems are linked and com- light lashes and the warning
plement the ABS. be advisable to disarm the ASR and
ESP systems, so that the wheels can light comes on, accompanied
The ASR system optimises drive to move freely and regain grip. by an audible signal and the
prevent the wheels skidding, by act- message "ESP/ASR not function-
ing on the brakes of the drive wheels F Press the "ESP OFF" switch, lo- ing" on the multifunction display.
and on the engine. It also allows the cated on the central section of the
fascia. Contact a PEUGEOT dealer to have
directional stability of the vehicle to the systems checked.
be improved on acceleration.
If there is a variation between the
trajectory followed by the vehicle and
that required by the driver, the ESP The switch lights up and the
system automatically acts on the warning light comes on: the
engine and the brake of one or more ASR and ESP systems are
wheels, in order to put the vehicle The ESP/ASR systems
disarmed. offer exceptional safety
back on course.
in normal driving, but this
should not encourage the
driver to take extra risks or
These are triggered again: drive at high speed.
F automatically if the ignition is The correct functioning of these
switched off, systems depends on observation
Operation of the ASR and ESP F automatically above 30 mph of the manufacturer's recommenda-
systems (50 km/h), tions regarding the wheels (tyres
F manually by pressing the switch and rims), the braking components,
The warning light lashes if the electronic components, and the
the ASR or ESP is activated. again.
PEUGEOT assembly and operation
procedures.
After an impact, have the systems
checked by a PEUGEOT dealer.
15-03-2004
126
YOUR 307 SW IN DETAIL
Operation Recalling the memorised
F Place switch 1 in the ON position. speed
A speed can be memorised. After cancellation, press button 4.
F Place switch 1 in the OFF position Your vehicle will return to the last
to cancel. memorised speed.
15-03-2004
127
YOUR 307 SW IN DETAIL
Selecting the function Cancelling the memorised speed
F Place switch 1 in the CRUISE If you wish to cancel the memorised
position. The cruise control is speed:
not yet active and no speed has F Press button 4 or the brake or
been memorised. The display in- clutch pedal. The display indicates
dicates: (e.g. at 70 mph (110 km/h)):
15-03-2004
129
YOUR 307 SW IN DETAIL
Selecting the function Exceeding the programmed
speed
F Place switch 1 in the LIMIT posi-
tion. The limiter is not yet active. Pressing the accelerator to exceed the
By default the display indicates: programmed speed will have no ef-
fect unless the pedal is pressed irmly
(passing the point of resistance).
The limiter is deactivated temporarily
and displays the speed which lashes
(e.g. at 70 mph (110 km/h)):
15-03-2004
131
YOUR 307 SW IN DETAIL
AIR BAGS
The air bags have been designed
to maximise the safety of the
occupants in the event of serious
collisions. They work in conjunction
with the force-limiting seat belts. The
electronic detectors register and
analyse any abrupt deceleration of
the vehicle: if the triggering thresh-
old is reached, the air bags inlate
instantly and protect the occupants
of the vehicle. Disarming the passenger
Immediately after the impact, the air air bag*
bags delate rapidly so that they do To ensure the safety of your child,
not hinder the visibility of the occu- it is essential to disarm the pas-
pants nor their exit if necessary from senger air bag when you install a
the vehicle. FRONT AIR BAGS rear-facing child seat on the front
The air bags are not deployed in These are folded in the centre of the passenger seat. Otherwise, the
the case of collisions which are not steering wheel for the driver and in child would risk being seriously
serious, for which the seat belt is the fascia for the front passenger. injured or killed if the air bag were
suficient to ensure maximum protec- They are deployed simultaneously, to inlate.
tion. The seriousness of a collision except in cases where the passenger
depends on the nature of the obsta- F With the ignition switched off,
air bag is disarmed. insert the key into the passenger
cle and the speed of the vehicle at
the moment of the collision. air bag disarming switch 1, turn
it to the "OFF" position, then re-
Air bags only operate when the move the key keeping the slot in
ignition is switched on. Front air bag fault this position.
Note: the gas escaping from the air The air bag warning light on the in-
bags can be a minor irritant. If this warning light comes strument panel is lit throughout the
on, accompanied by an disarming process.
audible signal and the
message "Air bag fault"
on the multifunction display, contact
a PEUGEOT dealer to have the
system checked.
* According to destination.
15-03-2004
132
YOUR 307 SW IN DETAIL
In the "OFF" position, the passenger SIDE AIR BAGS* AND
air bag will not be triggered in the CURTAIN AIR BAGS*
event of an impact.
As soon as the child seat is removed, The side air bags are incorporated
turn the air bag slot to the "ON" po- into the front seat backs on the door
sition to re-activate the air bag and side.
thus ensure the safety of your pas- The curtain air bags are incorporated
senger in the event of an impact. into the door pillars and the upper
part of the passenger compartment.
Disarming check They are deployed independently of
each other depending on which side
This is conirmed by an indicator light the collision occurs.
accompanied by a message on the
multifunction display. Operating check
This is conirmed by an indicator
light, accompanied by an audible
signal and a message on the multi-
With the ignition on (2nd function display.
notch), illumination of this
warning light accompanied
by the message "Passenger If this indicator light comes
air bag deactivated" on the on, accompanied by an audi-
multifunction display, indicates that ble signal and the message
the passenger air bag is disarmed "Air bag fault" on the multi-
(switch in the "OFF" position). function display, contact a
PEUGEOT dealer to have the sys-
tem checked.
* According to destination.
15-03-2004
133
YOUR 307 SW IN DETAIL
For the front, side* and Front air bags Curtain air bags*
curtain* air bags to be
fully effective, observe the • Do not drive holding the steering • Do not ix or glue anything to
following safety rules: wheel by its spokes or resting your the pillars or the roof. This could
hands on the centre part of the cause injury to the head when the
wheel. curtain air bag inlates.
• Wear a correctly adjusted seat • Passengers must not place their • Do not remove the bolts from
belt. feet on the fascia. the grab handles installed on the
roof, they play a part in securing
• Sit in a normal upright position. • Smoke as little as possible; the curtain air bags.
deployment of the air bags can
• Do not leave anything between cause burns or the risk of injury
the occupants of the front seats from a cigarette or pipe.
and the air bags (a child, pet,
object). • Never remove or pierce the steering
wheel or hit it violently.
This could hamper the opera-
tion of the air bags or injure the
occupants. Side air bags*
• All work on the air bag system • Only put approved covers on the
is strictly forbidden unless it is seats. Contact your PEUGEOT
carried out by qualiied personnel dealer.
of the PEUGEOT network. • Do not ix or glue anything to the
• After an accident or if the vehicle seat backs. This could cause injury
has been stolen or broken into, to the chest or arms when the side
have the air bag systems checked. air bag inlates.
• Do not sit with the upper part of the
body any nearer to the door than
necessary.
* According to destination.
15-03-2004
132
YOUR 307 SW IN DETAIL
In the "OFF" position, the passenger SIDE AIR BAGS* AND
air bag will not be triggered in the CURTAIN AIR BAGS*
event of an impact.
As soon as the child seat is removed, The side air bags are incorporated
turn the air bag slot to the "ON" po- into the front seat backs on the door
sition to re-activate the air bag and side.
thus ensure the safety of your pas- The curtain air bags are incorporated
senger in the event of an impact. into the door pillars and the upper
part of the passenger compartment.
Disarming check They are deployed independently of
each other depending on which side
This is conirmed by an indicator light the collision occurs.
accompanied by a message on the
multifunction display. Operating check
This is conirmed by an indicator
light, accompanied by an audible
signal and a message on the multi-
With the ignition on (2nd function display.
notch), illumination of this
warning light accompanied
by the message "Passenger If this indicator light comes
air bag deactivated" on the on, accompanied by an audi-
multifunction display, indicates that ble signal and the message
the passenger air bag is disarmed "Air bag fault" on the multi-
(switch in the "OFF" position). function display, contact a
PEUGEOT dealer to have the sys-
tem checked.
* According to destination.
15-03-2004
133
YOUR 307 SW IN DETAIL
For the front, side* and Front air bags Curtain air bags*
curtain* air bags to be
fully effective, observe the • Do not drive holding the steering • Do not ix or glue anything to
following safety rules: wheel by its spokes or resting your the pillars or the roof. This could
hands on the centre part of the cause injury to the head when the
wheel. curtain air bag inlates.
• Wear a correctly adjusted seat • Passengers must not place their • Do not remove the bolts from
belt. feet on the fascia. the grab handles installed on the
roof, they play a part in securing
• Sit in a normal upright position. • Smoke as little as possible; the curtain air bags.
deployment of the air bags can
• Do not leave anything between cause burns or the risk of injury
the occupants of the front seats from a cigarette or pipe.
and the air bags (a child, pet,
object). • Never remove or pierce the steering
wheel or hit it violently.
This could hamper the opera-
tion of the air bags or injure the
occupants. Side air bags*
• All work on the air bag system • Only put approved covers on the
is strictly forbidden unless it is seats. Contact your PEUGEOT
carried out by qualiied personnel dealer.
of the PEUGEOT network. • Do not ix or glue anything to the
• After an accident or if the vehicle seat backs. This could cause injury
has been stolen or broken into, to the chest or arms when the side
have the air bag systems checked. air bag inlates.
• Do not sit with the upper part of the
body any nearer to the door than
necessary.
* According to destination.
15-03-2004
134
PRACTICAL INFORMATION
8 - Dipstick.
2 - Windscreen/headlamp* wash
5 - Battery.
reservoir.
9 - Engine oil reservoir.
5 - Battery.
2 - Windscreen/headlamp* wash 9 - Engine oil reservoir.
reservoir.
6 - Fuse box.
8 - Dipstick.
2 - Windscreen/headlamp*
5 - Battery. 9 - Engine oil reservoir.
wash reservoir.
10 - Priming pump.
* According to destination.
15-03-2004
140
PRACTICAL INFORMATION
CHECKS Manual gearbox
Battery This does not require an oil change.
Check the level in accordance with the
At the start of winter, have your bat- manufacturer's servicing schedule.
tery checked by a PEUGEOT dealer.
To check the main levels and cer-
Air filter and passenger tain components, in accordance
compartment filter with the manufacturer's servicing
schedule, refer to the pages of
Have the ilter elements replaced the servicing booklet which corre-
regularly. If you drive in dusty spond to your vehicle's engine.
conditions, change them twice as
often.
Brake pads
Brake pad wear depends on the style
of driving, in particular for vehicles
which are used in town, over short
distances.
It may be necessary to check the
thickness of the pads, even between
services.
Handbrake
Only use products recom-
Where the handbrake travel is too mended by PEUGEOT.
great or there is a reduction in the
performance of the system, the To ensure best perform-
handbrake should be adjusted, even ance from components
between services. as important as the power
steering and the braking system,
Have the system checked by a PEUGEOT selects and offers
PEUGEOT dealer. quite speciic products.
To prevent damage to the elec-
Oil filter trical units, avoid washing the
engine.
Change the ilter regularly, in accord-
ance with the servicing schedule.
15-03-2004
141
PRACTICAL INFORMATION
RUNNING OUT OF FUEL 2 litre HDI engine
(DIESEL)
- ill the fuel tank with at least ive
If you should run out of fuel, it is nec- litres of diesel,
essary to re-prime the circuit. - squeeze and release the manual
The repriming pump, the transpar- re-priming pump, until you feel re-
ent pipe, and the degas screw are sistance during the manoeuvre,
located under the bonnet (see cor- - operate the starter until the engine
responding drawing): starts.
15-03-2004
142
PRACTICAL INFORMATION
CHANGING A WHEEL
Tools
Parking the vehicle Access to the spare wheel
The following tools are located: F As far as possible, park the vehi- F Open the boot.
- in the right-hand trim of the boot, cle on level, stable and non-slip- F Open the lap using the lug to re-
1 - Wheelbrace. pery ground. lease the winch and gain access
2 - Removable towing eye. F Apply the handbrake, switch off to its control nut.
3 - Sockets for anti-theft bolts. the ignition and engage irst or F Unscrew the nut fully, using the
reverse gear (position P for the wheelbrace 1, to unroll the winch
automatic gearbox). cable.
- in the holder in the centre of the
spare wheel,
4 - Jack with handle.
5 - Centralising tool.
6 - Bolt cover tool.
7 - Removable chock.
15-03-2004
143
PRACTICAL INFORMATION
F Detach the wheel/holder assem- Removing the wheel F Place the jack 4 in contact with
bly from the rear of the vehicle. one of the four locating points A
F Take out the notched hook to re- F Slide the holder cover to gain ac- on the sub-frame, the one which
lease the wheel, as shown in the cess to the tools. is closest to the wheel to be
illustration. F Place the chock 7 under the wheel changed.
diagonally opposite to the one to F Extend the jack 4 until its base is
be changed. in contact with the ground. Ensure
F Remove the trim, using the wheel- that the centre line of the base of
brace 1, pulling at the valve pas- the jack is straight above the lo-
sage hole (for vehicles itted with cating point A used.
steel wheels). F Raise the vehicle.
F Loosen the wheel bolts (see § F Remove one bolt and install the
"Special features of alloy wheels" centralising tool 5 in its place.
for vehicles itted with alloy F Unscrew the other bolts and re-
wheels). move the wheel.
15-03-2004
144
PRACTICAL INFORMATION
Fitting a wheel F Close the lap using the lug to lock
the winch. For your safety, always
F Position the wheel using the cen- change the wheel:
tralising tool 5 to assist you. F Store the rest of the tools in the
F Tighten the bolts by hand and re- right-hand trim of the boot.
move the centralising tool 5. - on level, stable, non-slippery
F Partly tighten the bolts using the ground,
wheelbrace 1. - with the handbrake on and the
F Fold the jack 4 and remove it. ignition switched off,
F Fully tighten the bolts using the - with irst or reverse gear en-
wheelbrace 1. gaged (position P for the auto-
F Replace the wheel trim, starting matic gearbox),
by placing the wheel trim notch - with the vehicle chocked.
opposite the valve, and press it on
using the palm of the hand.
F Put the corresponding tools in the Never go underneath a vehicle
holder and secure its cover. that is supported only by a jack
(use a ramp).
F Place the holder on the ground
and align the spare wheel on it.
F Pass the notched hook into the Never reit the holder under
holder cover. the vehicle without the spare
F Reit the wheel under the vehicle wheel.
tightening the winch control nut
using the wheelbrace 1. Do not use a screwdriver in
F Fully tighten and check that place of the wheelbrace to un-
the wheel is horizontally lush wind or wind the winch.
against the rear loor.
After changing the wheel:
- have the correct positioning of
the punctured wheel, the tighten-
ing of the bolts and the tyre pres-
sure checked by a PEUGEOT
dealer as soon as possible.
- have the punctured tyre repaired
and reit it to the vehicle as soon
as possible.
- have the correct positioning of
the spare wheel checked by a
PEUGEOT dealer.
15-03-2004
145
PRACTICAL INFORMATION
15-03-2004
146
PRACTICAL INFORMATION
F Turn the protective cover corre-
sponding to the faulty bulb a quar-
ter of a turn and remove it.
F Disconnect the connector.
F Press the end of the securing clip
to free it. Change the bulb.
F When itting the new bulb, ensure
that the direction notches are po-
sitioned correctly and the securing
clip is ixed properly.
F Reconnect the connector.
F Reit the protective cover, posi-
tioning it with the arrow upwards, 4 - Side lights (W 5 W).
CHANGING A BULB then turn it a quarter of a turn to F Pull the socket rearwards, remove
the right. the bulb and change it.
Front lights
The headlamps are itted with poly- 5 - Direction indicators
Note: on the right-hand side, remove carbonate glass with a protective
the style cover, ixed with two plastic (PY 21 W amber).
coating. Do not clean them with a F Turn the bulb holder a quarter of a
screws, to access the bulbs. Handle dry or abrasive cloth, nor with a
the bulbs with a dry cloth. turn and remove it.
detergent or solvent product. Use
1 - Dipped beam headlamps a sponge and soapy water. F Change the bulb.
(H7-55 W).
2 - Main beam headlamps Note: In certain climatic conditions
(H1-55 W). (low temperature, humidity), con-
3 - Front fog lamps (H1-55 W). densation inside the headlamp
glass is normal; it disappears a few
minutes after the lights are switched
on.
15-03-2004
147
PRACTICAL INFORMATION
Amber coloured bulbs
(direction indicators and
side repeaters), must be
replaced with bulbs of
identical speciication and
colour.
15-03-2004
148
PRACTICAL INFORMATION
Rear lights F Press the tab A and remove the Third brake light:
bulb holder. 4 W 5 W bulbs.
1 - Brake lights (P 21 W). F Change the faulty bulb.
2 - Side lights (R 5 W). F Remove the tailgate upper trim
carefully by unclipping it on either
3 - Direction indicators (P 21 W). Note: if necessary use the wheel- side, perpendicular to its direction
4 - Reversing light (P 21 W), left brace to remove the bolts. of engagement.
side. When reitting, take care to position F Insert a screwdriver into the two
Fog lamp (P 21 W), right side. the bulb holder and the bulb cor- outer holes B to press on the two
rectly. tabs C.
These 5 bulbs are changed by re- F Push the light unit outwards while
moving the light: Number plate lights (W 5 W) maintaining the pressure on the
F Remove the respective boot side tabs.
trim to access the light. F Insert a small screwdriver in one F Pull the light unit outwards while
of the external holes of the lens. tilting it.
F Remove the mounting nut for the
light inside the boot. F Push the lens outwards to unclip F Change the faulty bulb.
it.
F Remove the mounting nut for the F When reitting, ensure that the
light outside the boot. F Remove the lens. light unit tabs are engaged cor-
F Remove the light. F Change the faulty bulb. rectly and that the tailgate upper
trim has been put back in place
F Unclip the harness. correctly.
15-03-2004
150
PRACTICAL INFORMATION
CHANGING A FUSE
The fuse boxes are located under
the fascia (left-hand side) and in the
engine compartment.
The spare fuses and special pliers A
are ixed to the inside of the lid of the
instrument panel fuse box.
Automatic gearbox reversing lights switch - Automatic gearbox starting inhibitor relay control -
1 10 A Manual gearbox reversing lights switch - Vehicle speed sensor - Water in diesel sensor.
Injection control unit - Fan unit relay control - Additional heating relay control - Automatic
4 10 A gearbox control unit - Automatic gearbox sequential control - Automatic gearbox shiftlock relay.
8 20 A Fan unit relay control - Engine control unit supply - Injection pump (Diesel).
Oxygen sensors - Exhaust gas recirculation solenoid valve - Ignition coil - Diesel high
15 30 A pressure regulator - Injectors supply (petrol) - Pre-heat unit - Air low sensor (Diesel) - Engine
control unit (Diesel) - Injection pump (Diesel) - Diesel heater.
Front right side light, rear right side light - Number plate and trailer lighting - Central locking/
12 10 A alarm//hazard warning lights/ESP switch lights - Air conditioning/ashtray light - Automatic
gearbox switch lights - Lighter.
Diagnostic plug - Steering wheel controls - Electrochromatic interior mirror - Brake pedal
18 10 A (stop) and clutch switches - Coolant level switch - Second brake switch.
19 30 A PARC shunt.
22 10 A Front left side light, rear left side light - Number plate and trailer lighting.
15-03-2004
154
PRACTICAL INFORMATION
ECONOMY MODE FUNCTION LOAD REDUCTION
After the engine has stopped, with
FUNCTION
the key in the accessories position, When driving, certain functions (air
certain functions (windscreen wiper, conditioning, heated rear screen,
electric windows, courtesy lights, heating system for passenger com-
audio equipment etc.) can only be partment of diesel vehicles, etc.) may
used for a cumulative duration of be switched off temporarily, depend-
thirty minutes, to prevent discharging ing on the level of battery charge.
the battery. Reactivation of these functions is
Once the thirty minutes are over, the automatic, once the battery charge
message "Economy mode active" is suficient.
appears on the multifunction display Note: at the risk of discharging the
and the active functions are put on battery, the functions that have been
standby.
CHANGING A WINDSCREEN switched off may be reactivated
WIPER BLADE To resume the use of these functions manually.
immediately, start the engine and let
Special front windscreen wiper it run for a few seconds.
position
F Within one minute of switching off
the ignition, operate the wipers
stalk to position the wiper blades
in the centre of the windscreen
(maintenance position).
Changing a wiper blade
F Lift the wiper arm, then unclip the
blade and remove it.
F Fit the new blade and push back
the arm.
Note: the shortest blade is itted on
the vehicle's right-hand windscreen
wiper arm.
To return the windscreen wipers
to their normal position, switch on A lat battery will prevent
the ignition and operate the wiper the engine from starting.
stalk.
15-03-2004
155
PRACTICAL INFORMATION
BATTERY
- Before disconnecting
To charge the battery using a the battery, you must
battery charger: wait for 2 minutes after
switching off the igni-
- Disconnect the battery. tion.
- Follow the instructions for use - Never disconnect a terminal
given by the battery charger manu- when the engine is running.
facturer.
- Reconnect starting with the nega- - Never charge a battery without
tive (-) terminal. irst disconnecting the terminals.
- Check that the terminals and - Close the windows and the
connectors are clean. If they are roof concealing shutter before
covered with sulphate (white or disconnecting the battery. If the
greenish deposit), disconnect them windows and the shutter do not
and clean them. operate normally following re-
connection of the battery, they
To start the vehicle from must be reinitialised (see section
another battery: "Reinitialisation of the electric
windows" and "Panoramic roof").
- Connect the red cable to the positive
(+) terminals of the two batteries. - After every reconnection of the
battery, switch on the ignition and
- Connect one end of the green or wait 1 minute before starting to
black cable to the negative (-) ter- allow the electronic systems to
minal of the slave battery. be initialised. If slight dificulties
- Connect the other end of the green are experienced after this, please
or black cable to an earth point on contact a PEUGEOT dealer.
the broken down vehicle as far as
possible from the battery.
Operate the starter, let the engine run.
Wait for the engine to return to idle,
then disconnect the cables.
15-03-2004
156
PRACTICAL INFORMATION
Special features of the automatic
gearbox
When towing with four wheels on the
ground, the following rules must be
obeyed:
- lever in position N,
- tow the vehicle at less than 30 mph
(50 km/h) over a maximum dis-
tance of 30 miles (50 km).
- do not add oil to the gearbox.
TOWING YOUR
VEHICLE
Without lifting From the rear:
(4 wheels on the road)
F Unclip the top of the cover using a
You should always use a tow bar. coin.
The removable towing eye is inside F Screw in the removable towing
the boot right-hand trim. eye as far as it will go.
15-03-2004
157
PRACTICAL INFORMATION
TOWING A TRAILER, Driving advice Tyres: check the tyre pressures of
CARAVAN, BOAT etc. the towing vehicle and of the trailer,
Distribution of loads: Distribute the observing the recommended pres-
Only use original PEUGEOT tow load in the trailer so that the heaviest sures.
bars that have been tested and ap- items are as close as possible to the
proved from the design stage of your axle and the nose weight approach-
vehicle. es the maximum permitted without Braking: towing increases the brak-
The tow bar must be itted by a exceeding it. ing distance.
PEUGEOT dealer. Lights: check the electrical signal-
Your vehicle is primarily designed ling on the trailer.
Cooling: towing a trailer on a slope
for transporting people and luggage increases the temperature of the
but it may also be used for towing a coolant. Side wind: take into acount the in-
trailer. creased sensitivity to side wind.
As the fan is electrically controlled,
Driving with a trailer subjects the tow- its cooling capacity is not dependent
ing vehicle to more signiicant stress on the engine speed.
and its driver must be particularly
careful. On the contrary, use a high gear to
lower the engine speed and reduce
Air density decreases with altitude, your speed.
thus reducing engine performance.
Above 1,000 metres, the maximum The maximum towing load on a long
towing load must be reduced by slope depends on the gradient and
10 % and so on for every 1,000 me- the outside temperature.
tres of altitude. In all cases, pay attention to the cool-
The rear parking assistance function ant temperature.
will be disarmed automatically when If the warning light comes on, stop
a towbar is itted. the vehicle and switch off the engine
as soon as possible.
15-03-2004
158
PRACTICAL INFORMATION
15-03-2004
159
PRACTICAL INFORMATION
ENTERTAINMENT SCREEN
KIT
This video assembly will enable the
rear passengers to pass the time
pleasantly while watching their fa-
vourite ilm or playing their favourite
game, by means, in particular, of the
connection of a DVD player or games
console to the central support, itted
between the front seats.
The entertainment screen kit con-
sists of:
- a 16/9ths, 7 inch, LCD colour moni-
tor with direction adjustment in the
three axes, The upper face of the monitor incor-
- two high frequency, wireless, ster- porates the following controls:
eo headphones, 1 - "POWER" button to switch the
- a removable support, monitor on/off.
- three audio/video sockets on the 2 - "FUNC" button for selection of the
ixed base and in the glove com- input source, AV1 or AV2.
partment. 3 - "WIDE" button to change the dis-
play format (normal, full screen,
The monitor and the support can be wide, cinema).
removed and stored, each in their
own protective cover. 4 - "MENU" button for selection of
the menus and settings.
The entertainment screen kit ac-
cepts all types of audio/video source, 5 - "5" and "6" buttons to change
PAL/NTSC compatible, such as: DVD the settings.
player, camcorder, games console, ... By pressing buttons 4 and 5, you can
These sources are connected to the adjust the brightness, the contrast,
three audio/video sockets, AV1 in the colours, ...
the glove compartment or AV2 on For further details, refer to the oper-
the ixed base. ating manuals "Video kit operation"
and "VMA8582 7 inch LCD colour
monitor".
15-03-2004
160
PRACTICAL INFORMATION
15-03-2004
161
PRACTICAL INFORMATION
ACCESSORIES FOR YOUR - Communication: Audio system,
307 SW telephone, hands-free kit, speak-
ers, ampliiers, CD changer,
For your PEUGEOT only use acces- navigation systems, entertainment
sories and original parts approved by screen kit, DVD player...
the manufacturer.
These accessories and parts are all - Customising: Alloy wheels, trims,
adapted to your PEUGEOT, after be- sport exhaust, aluminium or PVC
ing tested and approved for reliability door sills, mud laps...
and safety, which PEUGEOT cannot
guarantee for other products.
- Leisure: Tow bar, transverse roof
A wide choice of original accessories, bars, roof box, snow chains, ski
approved by PEUGEOT, is available carrier, roof bars bicycle carrier,
through the dealer network. They all tailgate bicycle carrier...
carry the PEUGEOT guarantee.
* According to destination.
15-03-2004
162
TECHNICAL DATA
PETROL ENGINES
MODELS:
Model codes 3HNFUB 3HNFUE 3HRFNB 3HRFNE
3HNFUC/IF 3HNFUF/IF 3HRFNC/IF 3HRFNF/IF
15-03-2004
163
TECHNICAL DATA
DIESEL ENGINES
MODELS:
Model codes
3H9HZC 3H9HYB 3HRHYB 3HRHSB 3HRHRH
ENGINES 1.6 litre Turbo HDI 16V 2 litre 2 litre 2 litre 16V
Turbo HDI Turbo HDI Turbo HDI
90 bhp 110 bhp 136 bhp
3HNFUB
1.6 litre 16V Manual 28.5 (9.9) 44.8 (6.3) 36.7 (7.7) 178
3HNFUC/IF
3HNFUE
1.6 litre 16V Automatic 25.3 (11.2) 44.1 (6.4) 34.0 (8.3) 194
3HNFUF/IF
3HRFNB
2 litre 16V Manual 24.6 (11.5) 44.8 (6.3) 34.0 (8.3) 194
3HRFNC/IF
2 litre 16V Automatic 3HRFNE 21.6 (13.1) 43.5 (6.5) 32.1 (8.8) 206
2 litre 16V Automatic 3HRFNF/IF 21.6 (13.1) 44.1 (6.4) 31.7 (8.9) 211
2 litre Turbo HDI Manual 3HRHYB 39.8 (7.1) 62.8 (4.5) 52.4 (5.4) 143
90 bhp
2 litre 16V
Turbo HDI Manual 3HRHRH 38.7 (7.3) 60.1 (4.7) 50.4 (5.6) 148
136 bhp
15-03-2004
165
TECHNICAL DATA
WEIGHTS AND TOWING LOADS (in kg)
Version PETROL
Engine 1.6 litre 16V 2 litre 16V
Gearbox Manual Automatic Manual Automatic
Version DIESEL
2 litre 16V
Engine 1.6 litre Turbo HDI 2 litre Turbo 2 litre Turbo Turbo HDI
16V HDI 90 bhp HDI 110 bhp
136 bhp
Gearbox Manual Manual Manual Manual
Model codes: 3H9HZC 3H9HYB 3HRHYB 3HRHSB 3HRHRH
• Kerb weight 1 477 - 1 465 1 496 1 567
• Gross vehicle weight (GVW) 2 050 - 1 984 2 016 2 075
• Gross train weight (GTW)* 3 250 - 3 484 3 516 3 475
• Unbraked trailer 700 - 730 745 750
• Braked trailer (within GTW) 1 200 - 1 500 1 500 1 400
• Maximum nose weight 56 - 60 60 56
* The speed of a towing vehicle is limited to 60 mph (100 km/h).
15-03-2004
166
TECHNICAL DATA
DIMENSIONS (in mm)
15-03-2004
167
TECHNICAL DATA
IDENTIFICATION FEATURES D. Tyres and paint colour Wheels which are itted with
OF YOUR 307 SW reference. 17 inch tyres cannot be itted with
The label D on the pillar, near the snow chains. For further informa-
hinges of the driver's door, gives: tion, contact a PEUGEOT dealer.
A. Manufacturer's plate. - the wheel and tyre sizes,
- the brands of tyres* approved by E. Fuel consumption igures* in
B. Serial number on the the manufacturer, the corner of the windscreen.
bodywork.
- the tyre pressures (the tyre pres-
sure must be checked when
C. Serial number on the fascia. the tyre is cold, at least once a
month),
- the paint colour reference*.
* According to country.
15-03-2004