Professional Documents
Culture Documents
Pantalla anterior
Bienvenido: cr120hxv
Producto: ENGINE - MACHINE
Modelo: C4.4 ENGINE - MACHINE 44601874
Configuración: C4.4 Industrial Engine 44600001-UP
Especificaciones
C4.4 (Mech) Industrial Engine
Número de medio -KENR6248-02 Fecha de publicación -01/06/2007 Fecha de actualización -08/09/2016
i03454403
Cylinder Block
SMCS - 1201
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-9013 Silicone Sealant 1
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/techdoc/techdoc_frameset.jsp&calledpage=/sisweb/siswe… 1/3
19/2/2020 C4.4 Industrial Engine 44600001-UP(SEBP4821 - 51) - Sistemas y componentes
Illustration 1 g00924764
Typical example
The maximum permissible wear for the cylinder bore ... 0 to 0.15 mm (0 to 0.0059 inch)
Diameter of the bore in the cylinder block for the number 1 camshaft bearing ... 55.56 to 55.59 mm
(2.188 to 2.189 inch)
Diameter of the bore in the cylinder block for the number 2 camshaft journal ... 50.54 to 50.60 mm
(1.990 to 1.992 inch)
Diameter of the bore in the cylinder block for the number 3 camshaft journal ... 50.038 to 50.090 mm
(1.969 to 1.972 inch)
Bore in the cylinder block for the main bearings ... 80.416 to 80.442 mm (3.1660 to 3.1670 inch)
Use the following procedure in order to install the main bearing cap bolts:
1. Apply clean engine oil to the threads of the main bearing cap bolts.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/techdoc/techdoc_frameset.jsp&calledpage=/sisweb/siswe… 2/3
19/2/2020 C4.4 Industrial Engine 44600001-UP(SEBP4821 - 51) - Sistemas y componentes
2. Put the main bearing caps in the correct position that is indicated by a number on the top of the main
bearing cap. Install the main bearing caps with the locating tabs in correct alignment with the recess in the
cylinder block.
Torque for the main bearing cap bolts. ... 245 N·m (180 lb ft)
Illustration 2 g00938203
Use the following procedure in order to install the allen head bolts for the bridge.
1. Use a straight edge in order to ensure that the bridge is aligned with the front face of the cylinder block.
Torque for the allen head bolts ... 16 N·m (12 lb ft)
3. When the bridge is installed on the cylinder block, apply a thin bead of Tooling (A) into groove (7) at each
end of the bridge.
Note: The oil pan must be installed within 10 minutes of applying the sealant.
Total height of the cylinder block between the top and the bottom faces. ... 441.173 to 441.274 mm
(17.3689 to 17.3729 inch)
Copyright 1993 - 2020 Caterpillar Inc. Wed Feb 19 2020 12:24:26 GMT-0300 (hora de verano de Chile)
Todos los derechos reservados.
cr120hxv
Red privada para licenciados del SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/techdoc/techdoc_frameset.jsp&calledpage=/sisweb/siswe… 3/3