Professional Documents
Culture Documents
by FUNHYDRO
The pictures show a prototype of a small Ebb & flow as a hydroponic ebb & flow system or as an
hydroponic system I have made as part of a school automated water table for plants potted in soil or coco
project. The project covers the development of a etc. This opportunity makes the system unique
small water/hydroponic-table for various uses. The compared to other products/guides.
main purpose of this specific system was to develop
a system that allows the user to use the system either
For the construction of a table like the one shown you · *Multitool/drill etc.
will need some tools. The table can be made with
simple tools. The essential tools will be marked with a · *Drill bit
star*. The other tools listed are tools that will make
the process faster and/or easier. · *Hacksaw blade
· *Sandpaper · File
The chosen materials should all be relative easy to pick up at any location. Some materials where chosen because
of aesthetics, others because of use, availability etc. A few parts came from reclaimed materials. The use of
recycled/reclaimed materials is highly recommended.
Materials note: IKEA Kuggis boxes are highly recommended for a nice and beautiful finish. It is a bit hard to work
in these boxes compared to other storage boxes because of the material thickness. If you don’t care about the
looks of it I would choose a softer and cheaper solution. But if you do like the looks of it it’s definitely worth it.
Construction of the system will be divided into five parts. The picture above shows the system divided into the five
construction parts. We will start from the top and work our way down.
First you have to find out how many holes you want in with sanding paper.
your lid. I went with 6 holes but 8 would also work. If
you want to use the system as a cloner u should Note: if you dont have a hole saw mark the outline of
consider adding more holes. the holes and then drill with a small hole on the inside
of the diameter all the way around. then cut it out with
Start out by marking the holes in the position where a hacksaw blade and finish with a file or grinder.
you want them. I marked out 6 holes and cut them out
with a 52 mm hole saw. then i gave it a quick finish
The water tray is the part with the most steps to finish.
1. Start by trimming down your funnel until you get something with a nice groove to mount in the water
tray.
2. Then you mark the center of your tray. this is where you want to place you fill/drain tube.
3. Drill the center hole to a diameter that fits the funnel.
4. Hot glue the funnel to the watertray.
5. Cut a 1 cm piece of the drain pipe and half it to make U shaped piece.
6. Mount the U with glue on top of the funnel.
7. 10 cm lengthwise from center hole you mark the hole for the overflow drain.
8. Cut the hole to fit the outside diameter of the seal for drain pipe.
9. Mount the seal for drain pipe.
10. Mount Eheim 9mm tube to the funnel.
11. Mount the waterpump to the Eheim tube.
12. Secure the Eheim tube with cable ties.
13. Cut and mount a suiting piece of aquarium filter under the u shaped holder.
14. (optional) You can heat up the bottom of the water tray with a heating gun to make the material soft.
then you can make sure the fill/drainpipe is the lowest part of the tray to allow complete draining.
The drain pipe is a quite simple part to make. But is also a part that needs a certain amount of precision to make it
look good.
1. Start by cutting your drain pipe to the desired length. with the boxes i used this was 12 cm.
2. Glue a piece of squared paper to the pipe.
3. Drill 3 rows of holes in every second square. first hole should be 5mm from the top last hole 15 mm
from the top. Then fill out the empty squares with 2 rows of holes.
4. Finish the pipe with a knife or sand paper.
5. Cut and mount aquarium filter into the drain pipe.
making the lid for the water tray is quite simple. but can be a bit time consuming. depending how nice you want it.
The water reservoir dont need much work. You just need to cut out a suiting piece of transparent acrylic and glue it
over the hole in the side.
Step 9: Assembly
Now you are ready to assemble your hydroponics system. This guide have taken you through the steps of creating
it and i am sure youalready know how to assemble the parts you have been working with.
Next thing to mount is a timer and some small netpots filled with claypebbles.
Now you are ready to grow plants in your new hydroponic system!
I hope that all of you enjoyed viewing this project. I certainly enjoyed creating it. I will be pleased for any
constructive feedback regarding this project.
I hope to get back to you all with a guide for growing in this small system.
Sincerely FUNHYDRO