Professional Documents
Culture Documents
Technical data
Property Value Unit Method
Appearance Free-flowing, colourless liquid - -
Active ingredient Alkylalkoxysilane - -
Solvent Ethanol - -
Strength 40 % -
Odour Of alcohol - -
O 3
Density (20 C) 0.824 g/cm DIN 51757
O
Boiling point 81 C -
Viscosity 1.12 mPa.s DIN 53015
O
Flash point <21 C DIN 51755
Dynasylan ®BSM 40%
Application rate ®
with Dynasylan BSM 40%. Glass, wood and metal
Depending on how absorbent the substrate is, ®
is not attacked by Dynasylan BSM 40%. Neither is
experience has shown that concrete requires
2 most plastics used in construction. Therefore
approx. 0.4 – 0.6 l/m and sand lime brickwork
2 covering is normally not necessary. To make it
approx. 0.7 l/m . Porous façade tiles, on the other
2 sure we recommend carrying out a test. In the
hand, can require well in excess of 1 l/m
® worst case, product not absorbed by the substrate
Dynasylan BSM 40%. The amount to be applied
may react with atmospheric moisture to form a
has to be determined by a trial application.
greasy, glossy silicone resin film, which can easily
be removed if cleaned immediately using
Directions for use
conventional cleaning agents, or alcohol.
The substrates to by treated should by dry and
®
clean in order to ensure deep penetration of the Dynasylan BSM 40% reacts with the interface in
active ingredient. During application the outside pores and capillaries of the mineral surface and
temperature and the temperature of the substrate forms invisible, water-repellent interfacial
o compounds. However, since it is frequently
should be within the range from 0 to 45 C. The
material should not be applied if there is a strong unknown whether the material has been previously
wind or if it is raining. The material must not come treated, and the exact type of treatment, a test
into contact with water either before of during use. should always be performed on a small area to
® make sure that not undesired secondary
Dynasylan BSM 40% must be applied by flow-
phenomena occur. Plants in the vicinity of the
coating to the saturation point. This is achieved by
substrate to be treated should be protected against
allowing it to flow without pressure against the ®
contact with Dynasylan BSM 40%.
surface to be treated. All liquid delivery devices are
suitable (airless spray guns, for example). The
Safety information
material must not be atomized to applied with a
Before considering the use of any chemical read its
brush.
Safety Data Sheet thoroughly for safety and
®
Dynasylan BSM 40% must remain in contact with toxicological data as well as for information on
the substrate for several seconds as a liquid film. proper transportation, storage and use. The Safety
Horizontal surfaces should have a shiny, wet Data Sheet is available upon request from your
appearance for 3-5 seconds. Vertical surfaces local BASF Construction Chemicals SA
should exhibit a 30-50cm shiny curtain of liquid. representative.
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or
implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any
labour involved in the application are beyond our control.
As all BASF’s technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.
BASF Construction Chemicals South Africa (Pty) Ltd
P.O. Box 420, Westonaria, 1780 852 Sixteenth Road, Midrand
11 Pullinger Street, Westonaria, 1779 PO Box 2801, Halfway House, 1685
Tel: +27 11 754 1343 Tel: +27 11 203 2405
Fax: +27 11 754 1105
Website : basf -cc.co.za