Professional Documents
Culture Documents
Rectifier Diodes PBYR1545CT, PBYR1545CTB Series Schottky Barrier
Rectifier Diodes PBYR1545CT, PBYR1545CTB Series Schottky Barrier
GENERAL DESCRIPTION
Dual, common cathode schottky rectifier diodes in a conventional leaded plastic package and a surface mounting
plastic package. Intended for use as output rectifiers in low voltage, high frequency switched mode power supplies.
The PBYR1545CT series is supplied in the SOT78 conventional leaded package.
The PBYR1545CTB series is supplied in the SOT404 surface mounting package.
1 anode 1 (a)
2 cathode (k) 1
3 anode 2 (a) 2
1 23 1 3
tab cathode (k)
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134)
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
PBYR15 40CT 45CT
PBYR15 40CTB 45CTB
VRRM Peak repetitive reverse - 40 45 V
voltage
VRWM Working peak reverse - 40 45 V
voltage
VR Continuous reverse voltage Tmb ≤ 107 ˚C - 40 45 V
IO(AV) Average rectified forward square wave; δ = 0.5; - 15 A
current (both diodes Tmb ≤ 128 ˚C
conducting)
IFRM Repetitive peak forward square wave; δ = 0.5; - 15 A
current (per diode) Tmb ≤ 128 ˚C
IFSM Non-repetitive peak forward t = 10 ms - 135 A
current per diode t = 8.3 ms - 150 A
sinusoidal; Tj = 125 ˚C prior to
surge; with reapplied VRRM(max)
IRRM Peak repetitive reverse pulse width and repetition rate - 1 A
surge current per diode limited by Tj max
Tj Operating junction - 150 ˚C
temperature
Tstg Storage temperature - 65 175 ˚C
1. It is not possible to make connection to pin 2 of the SOT404 package.
THERMAL RESISTANCES
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Rth j-mb Thermal resistance junction per diode - - 3 K/W
to mounting base both diodes - - 2 K/W
Rth j-a Thermal resistance junction SOT78 package in free air - 60 - K/W
to ambient SOT404 package, pcb mounted, minimum - 50 - K/W
footprint, FR4 board
ELECTRICAL CHARACTERISTICS
Tj = 25 ˚C unless otherwise specified
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
VF Forward voltage per diode IF = 7.5 A; Tj = 125˚C - 0.44 0.57 V
IF = 15 A; Tj = 125˚C - 0.63 0.72 V
IF = 15 A - 0.62 0.84 V
IR Reverse current per diode VR = VRWM - 0.22 1 mA
VR = VRWM; Tj = 100˚C - 18 25 mA
Cd Junction capacitance per VR = 5 V; f = 1 MHz, Tj = 25˚C to 125˚C - 270 - pF
diode
Forward dissipation, PF (W) PBYR745 Tmb(max) (C) Reverse current, IR (mA) PBYR1545CT
8 126 100
Vo = 0.42 V
7 Rs = 0.02 Ohms 129
D = 1.0
125 C
6 132 10
0.5
5 135 100 C
0.2
4 0.1 138 1 75 C
3 tp 141
I tp D= 50 C
T
2 144 0.1
Tj = 25 C
1 t 147
T
0 150 0.01
0 2 4 6 8 10 12 0 25 50
Average forward current, IF(AV) (A) Reverse voltage, VR (V)
Fig.1. Maximum forward dissipation PF = f(IF(AV)) per Fig.4. Typical reverse leakage current per diode;
diode; square current waveform where IR = f(VR); parameter Tj
IF(AV) =IF(RMS) x √D.
6 132
a = 1.57
5 1.9 135
2.2
2.8
4 4 138 100
3 141
2 144
1 147
150 10
0 1 10 100
0 1 2 3 4 5 6 7 8
Average forward current, IF(AV) (A) VR / V
Fig.2. Maximum forward dissipation PF = f(IF(AV)) per Fig.5. Typical junction capacitance per diode;
diode; sinusoidal current waveform where a = form Cd = f(VR); f = 1 MHz; Tj = 25˚C to 125 ˚C.
factor = IF(RMS) / IF(AV).
Forward current, IF (A) PBYR1545CT Transient thermal impedance, Zth j-mb (K/W)
50 10
Tj = 25 C
Tj = 125 C
40
1
30
typ
20
0.1
PD tp tp
max D=
T
10
T t
0 0.01
1us 10us 100us 1ms 10ms 100ms 1s 10s
0 0.2 0.4 0.6 0.8 1 1.2 1.4
Forward voltage, VF (V) pulse width, tp (s) PBYR1545CT
Fig.3. Typical and maximum forward characteristic Fig.6. Transient thermal impedance per diode;
IF = f(VF); parameter Tj Zth j-mb = f(tp).
MECHANICAL DATA
Dimensions in mm
4,5
Net Mass: 2 g max
10,3
max
1,3
3,7
2,8 5,9
min
15,8
max
3,0 max
3,0
not tinned
13,5
min
1,3
max 1 2 3
(2x) 0,9 max (3x)
0,6
2,54 2,54 2,4
Notes
1. Refer to mounting instructions for SOT78 (TO220) envelopes.
2. Epoxy meets UL94 V0 at 1/8".
MECHANICAL DATA
11 max
15.4
2.5
MOUNTING INSTRUCTIONS
Dimensions in mm 11.5
9.0
17.5
2.0
3.8
5.08
Notes
1. Epoxy meets UL94 V0 at 1/8".
DEFINITIONS
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 1998
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.