Professional Documents
Culture Documents
> Port size: 1/4” ... 1/2” > High efficiency oil and
(ISO G/PTF) particle removal
> Excelon design allows > Quick release bayonet
in-line installation bowl
or modular installation > Service indicator
with other Excelon standard
products
Technical features
Medium: Flow: Ambient/Media temperature: Materials:
Compressed air only 10 dm3/s at port size: G3/8 Transparent bowl: Body: die cast aluminium
Maximum inlet pressure: Operating pressure: 6,3 bar (91 psi) -34 ... +50°C (-30 ... +122°F) Bowl: transparent PC, with or
Transparent bowl: Drain: Metal bowl: without steel guard
10 bar (145 psi) Manual, automatic -34 ... +65°C (-30 ... +150°F) alternative aluminium
Metal bowl: Automatic drain operating Air supply must be dry enough Element: synthetic fibre &
17 bar (250 psi) conditions (float operated): to avoid ice formation at PE foam
Remaining oil content: Bowl pressure required to temperatures below +2°C (+35°F). Elastomers: CR & NBR
0,01 mg/m3 at +21°C (69°Fi) close drain: > 0,3 bar (5 psi)
Particle removal: Bowl pressure required to Note:
To 0,01 µm open drain: ≤ 0,2 bar (2.9 psi) Install an F73G filter with a 5 µm
Port size: Minimum air flow required to filter element upstream of the F73C
G1/4, G3/8, G1/2, close drain: 0,1 dm3/s (0.2 scfm) filter for maximum service life.
1/4 PTF, 3/8 PTF, 1/2 PTF Manual operation: depress pin
inside drain outlet to drain bowl
Our policy is one of continued research and development. We therefore reserve the right to amend, 01/17
without notice, the specifications given in this document. (1998 - 8046c) © 2015 Norgren Inc. en 8.180.105.01
F73C - EXCELON® Modular System
Oil removal filters
Flow characteristics
Element saturated Element dry
Port size G3/8 Port size G3/8
bar
1,0
Inlet pressure bar (psi)
2,5
psi
bar
(15) (36)
0,4 1,0 2,5 6,3 8,0
6,3
(90) (15) (36) (90) (116)
5 5
0,3 0,3
8,0
Pressure drop Δp
Pressure drop Δp
4 (116)
3 3 0,2
0,2
2 2
0,1 0,1
1 1
0 0 0 0
0 2 4 6 8 10 dm3/s 0 4 8 12 16 dm3/s
0 4 8 12 16 20 scfm 0 8 16 24 32 40 scfm
Accessories
Wall mounting Quikclamp® Quikclamp with Quikmount pipe Porting block with 2/2 Shut-off valves (for 3/2 Shut-off valves (for
bracket wall bracket® adaptor *1) three alternative full technical specification full technical specification
1/4” ports see datasheet 8.180.600) see datasheet 8.180.600)
Page 3
0523110000000000 0881300000000000 0613633000000000 F73C-KITA0C 4444-01
*1) for shut-off valves
Our policy is one of continued research and development. We therefore reserve the right to amend,
en 8.180.105.02 without notice, the specifications given in this document. (1998 - 8046c) © 2015 Norgren Inc. 01/17
F73C - EXCELON® Modular System
Oil removal filters
Drawings Dimensions in mm
Projection/First angle
F73C 2
60
25
147
156
207
216
3
4
R1/8
R1/8
Accessories
Quikclamp® Quikclamp® with wall bracket Porting block Pipe adapter
74
24,5 46
51 36 18
24 6,5
6
36
51
51
ø 6,5
4
90°
1
45 21 10
102
51
33
83
4
1 Main ports 3/8”, 1/2” or 3/4”
ISO G/PTF
10 Ports 1/4” ISO G/PTF plugged
Wall mounting bracket Shut-off valves Porting block for pressure switch
60
52,5 67
58
11 38 - +
7,5 11 1 1,5
3
42 13
40
54
6
7
11 17 1 32 G1/2
48
61
14
19
44 40
57
14
38
1 Main ports
67
1
22
Our policy is one of continued research and development. We therefore reserve the right to amend,
01/17 without notice, the specifications given in this document. (1998 - 8046c) © 2015 Norgren Inc. en 8.180.105.03
F73C - EXCELON® Modular System
Oil removal filters
EN - Englisch
Warning
These products are intended for use in industrial compressed air systems Through misuse, age, or malfunction, components used in fluid power
only. Do not use these products where pressures and temperatures can systems can fail in various modes. The system designer is warned to
exceed those listed under »Technical features/data«. consider the failure modes of all component parts used in fluid power
Before using these products with fluids other than those specified, for systems and to provide adequate safeguards to prevent personal injury
non-industrial applications, life-support systems or other applications not or damage to equipment in the event of such failure.
within published specifications, consult System designers must provide a warning to end users in the system
IMI Precision Engineering, Norgren Inc. instructional manual if protection against a failure mode cannot be
adequately provided.
System designers and end users are cautioned to review specific warnings
found in instruction sheets packed and shipped with these products.
Our policy is one of continued research and development. We therefore reserve the right to amend,
en 8.180.105.04 without notice, the specifications given in this document. (1998 - 8046c) © 2015 Norgren Inc. 01/17