Professional Documents
Culture Documents
Technical features
Medium: Typical flow: Relieving: Materials:
Compressed air only See below Standard Body & bonnet: Aluminum alloy
Operation pressure: Main port size: Ambient/Media temperature: Bottom plug: Acetal
31 bar (450 psi) maximum 1 1/2” & 2” -34 ... 80°C (-30 ... +175°F) Valve: Aluminum and PA
Pressure range: Relieving port: Version with gauge: Elastomers: NBR
Standard: 3/4 PTF with PTF main ports -34 ... +65°C (-30 ... +149°F)
0,16 ... 17 bar (2.3 ... 246 psi) G1/4 with ISO G main ports Air supply must be dry enough to
With pilot regulator: Gauge port: avoid ice formation at temperatures
0,3 ... 8,5 bar (4.3 ... 123 psi) 1/4 PTF with PTF main ports below +2°C (+35°F).
Rc1/4 with ISO G main ports
G1 1/2 944 R40 included 0,3 ... 8,5 4,35 ... 123 3,85 R18-B05-RNLG
G2 944 R40 included 0,3 ... 8,5 4,35 ... 123 3,75 R18-C05-RNLG
G1 1/2 944 R41 included 6,9 ... 17 4,35 ... 123 3,85 R18-B06-RNSG
G2 944 R41 included 6,9 ... 17 4,35 ... 123 3,75 R18-C06-RNSG
*1) Typical flow with 7,0 bar (101 psi) inlet pressure, 6,3 bar (91 psi) set pressure and a 1 bar (14,5 psi)droop from set.
Our policy is one of continued research and development. We therefore reserve the right to amend, 05/18
without notice, the specifications given in this document. (1997 - 8134g) © 2015 Norgren Inc. en 8.350.200.01
R18
General purpose pressure regulators
Our policy is one of continued research and development. We therefore reserve the right to amend,
en 8.350.200.02 without notice, the specifications given in this document. (1997 - 8134g) © 2015 Norgren Inc. 05/18
R18
General purpose pressure regulators
psi
bar
8
psi
bar
100 100
6 6
80 80
1
Outlet pressure
Outlet pressure
60 4 60 4
2
40 40
2 2
20 20
0 0 0 0
0 200 400 600 800 dm3/s 0 20 40 60 80 dm3/s
Page 4
R3/4: MB006B R1/4-G1/8 150232818 R18-100R (R18)
3/4 NPT: MB006A R18-100R & 5945-41 (R18 & R40)
Our policy is one of continued research and development. We therefore reserve the right to amend,
05/18 without notice, the specifications given in this document. (1997 - 8134g) © 2015 Norgren Inc. en 8.350.200.03
R18
General purpose pressure regulators
Dimensions Dimensions in mm
Projection/First angle
1 Silencer
184
C
91
ØD
A
2
B
152
3 A B C D Model
R3/4 20 134 51 51 MB006B
3/4 NPT 20 134 51 51 MB006A
140
5 6
4 4
1 1
~ 271
247
91
91
~ 106
2 2
152
1 1/4” gauge port
152
2 3/4” relieving port
3 1/4” pilot port
3 4 Regulator R18
5 Regulator R40
6 Regulator R41
140
140
Our policy is one of continued research and development. We therefore reserve the right to amend,
en 8.350.200.04 without notice, the specifications given in this document. (1997 - 8134g) © 2015 Norgren Inc. 05/18
R18
General purpose pressure regulators
EN - Englisch
Warning
These products are intended for use in industrial compressed air systems Through misuse, age, or malfunction, components used in fluid power
only. Do not use these products where pressures and temperatures can systems can fail in various modes. The system designer is warned to
exceed those listed under »Technical features/data«. consider the failure modes of all component parts used in fluid power
Before using these products with fluids other than those specified, for systems and to provide adequate safeguards to prevent personal injury
non-industrial applications, life-support systems or other applications not or damage to equipment in the event of such failure.
within published specifications, consult System designers must provide a warning to end users in the system
IMI Precision Engineering, Norgren Inc. instructional manual if protection against a failure mode cannot be
adequately provided.
System designers and end users are cautioned to review specific warnings
found in instruction sheets packed and shipped with these products.
Our policy is one of continued research and development. We therefore reserve the right to amend,
05/18 without notice, the specifications given in this document. (1997 - 8134g) © 2015 Norgren Inc. en 8.350.200.05