Professional Documents
Culture Documents
Service
Service
Service
Horizontal Frequency
30kHz – 80kHz
TABLE OF CONTENTS
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Revision List
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
Power board
Main Board RS232 Connector
(Include: adapter, inverter)
For white balance
adjustment in factory
Key board Audio board mode
External Controls
1. D-Sub Cable
2. AC Power Cord
3. Audio Cable
• Power Indicator:
Green — Power On mode.
Orange — Off mode.
• MENU / ENTER:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD
menu when in Brightness /Contrast Adjust OSD status.
• Volume:
Increase volume or adjust function.
• Volume:
Decrease volume or adjust function.
OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off
and then press power button to turn the monitor on.
NOTES
• Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to
direct sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your
monitor.
• For maximum protection, repackage your monitor as it was originally packed at the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a
cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before
cleaning it.
Auto Config Yes N/A Auto Adjust the H/V Position, Focus and Clock of
picture.
No N/A Do not execute Auto Config, return to main menu.
Main Main
Sub Menu
Menu Menu Sub Menu Icon Description
Item
Item Icon
OSD
V. Position Adjust the vertical position of the OSD.
Setup
10
Analog Connector
1 5
6 10
11 15
11
12
(2)Backlight
13
2 Y
3
5 N
7 N
8
10 N
11
N N
12 13
Y Y
14 15 N
16
17
N
18 19
14
1) MCU initializes.
2) Is the EPROM blank?
3) Program the EPROM by default values.
4) Get the PWM value of brightness from EPROM.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EPROM.
Turn on the LED and set it to green color.
Scalar initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappears.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
15
Crystal
Panel Interface
20MHz
(CN503)
(X601)
H sync
V sync
RGB
EEPROM
OSD Control D-Sub
M24C16
Interface Connector
(U602)
(CN602) (CN301)
DB15_SDA,
DB15_SCL
EEPROM
M24C02
(U301)
16
Bridge Rectifier
AC input Rectifier Transformer diodes
EMI filter and Filter
Output MOSFET
Transformer
Q203、Q204
Circuit
Lamp
PWM
Feedback PWM
Circuit Control IC ON/OFF Control
DIM
17
B2
B1
RIN RIN
GNDR GNDR
TXD GIN GIN
RXD GNDG GNDG
DDC_CLK SOG SOG VCC2.5 VCC3.3 VAA1 VAA2 VAA3 VAA4
DDC_DAT BIN BIN
GNDB GNDB
ST_DET1 HSYNC HSYNC
ST_DET2 VSYNC VSYNC
VCC2.5
VCC3.3
R+ R+ VAA1
R- R-
G+ G+ VAA2
G- G-
B+ B+ VAA3
B- B-
CLK+ CLK+ VAA4
CLK- CLK-
3.INPUT
B3
ST_DET2
ST_DET1
DDC_CLK CSZ CSZ
VCPU VCC12V VCC5V DDC_DAT SCL SCL
RXD SDA SDA
TXD HWRESET HWRESET
INT INT
AD0 AD0
VCC5V AD1 AD1
AD2 AD2 B5
VCC12V AD3 AD3 PA[0..9]
PA[0..9] PA[0..9]
VCPU
Volume Volume
onPANEL_5V/3.3V VLCD
VCPU onBACKLITE PB[0..9]
VCC12V PB[0..9] PB[0..9]
VCC3.3
VCC2.5 6.MCU
VAA1
VAA2 VLCD
VAA3
VAA4
VCC5V B4
onBACKLITE
onPanel_5V/3.3V 5.PANEL INTERFACE
VCPU
VCC12V
VCC3.3
VCC2.5 AdjBACKLITE AdjBACKLITE
VAA1 VLCD
VAA2
VAA3
VAA4
VCC5V Title
VLCD 4.SCALER
TSU16AK
Size Document Number Rev
2.POWER B TOP D
Date: Wednesday, April 14, 2004 Sheet 1 of 6
18
VCC5V+
VCC5V
D202 SOT-252
VCC12V U201
R202 GS1D VCC2.5
VCC12V 6
RT9164
CN201 10K 1/16W 3 2
VI VO VCC2.5 4
GND 1 2 ON_OFF R201 4.7K 1/16W
GND
GND 3 4 DIM C210 C211 + C212
VCC12V 5 6 VCC12V D201 SS14
3
GND 7 8 GND C201 R212 4.7K 1/16W 0.1uF 47uF/16V 0.1uF
VCC5V VCC5V+
9 10 VCC5V 1
1
GND GND VCC5V onBACKLITE 6
11 12 0.1uF Q201
VCC5V 3,4,6
PMBS3904
2
VCPU C
CONN FB201
600 OHM
VCPU 6 B E
VCC5V
C202 C204
+ C203 + C205
Brightness VCC3.3
R204
10K 1/16W VCC3.3 4
3
C AIC1084-33M
3 2
VIN VOUT VAA1 4
B E
1
C214 ADJ C215 + C216 VAA2
VAA3 4
VAA4
VAA4 4
NEW
Circuit
VCC5V VCC5V VLCD
VLCD 5
VCC5V VCC3.3 VCC12V
R206
R214 delete R208
100uF/16V
0.1uF 10K 1/16W TSU16AK
Size Document Number Rev
B POWER D
Date: Friday, November 26, 2004 Sheet 2 of 6
19
75 1/16W
75 1/16W
SOG 4
9 PC5V R325 C301 C302 C303
R326
R327
15 5
10 VGA_CON 75 1/16W NC NC NC
VCC5V
R308
10K 1/16W
2
2
HSI FB304 150 OHM R310 1K 1/16W
HSYNC 4
D304
1
TZMC5V6-GS08 TZMC5V6-GS08 TZMC5V6-GS08
2.2K 1/16W 33pF 10K 1/16W 220pF R317 R318 C313
10K 1/16W U301
10K 1/16W 8 1 0.1uF
7 VCC A0 2
CLK_DDC R315 100 1/16W 6 WP A1 3
DAT_DDC R316 100 1/16W 5 SCL A2 4
SDA GND
M24C02WMN6
CN302
D321 D318
6 DDC_DAT
25 TZMC5V6-GS08 TZMC5V6-GS08
R 6 DDC_CLK
26
G 27 VCC5V DVI5V
B 29
RGB GND
2
28
HSYNC 8 D305
VSYNC 15
SYNC GND 6 CLK_DDC2 R319 100 1/16W DVI5V BAV70
DDC SCL 7 DAT_DDC2 R320 100 1/16W R321
DDC SDA 14 10K 1/16W
+5V 16 R322 100 1/16W
HPD ST_DET2 6
1
11
1/3shield 3 D314 D315 D316 C314 R323 R324 C315
2/4shield 19 LL5232B 5.6V 5% LL5232B 5.6V 5% LL5232B 5.6V 5% 10K 1/16W U302
0/5shield 22 0.1uF 10K 1/16W 8 1 0.1uF
clk shield 7 VCC A0 2
18 6 WP A1 3
DAT0+ B+ 4 SCL A2
17 5 4
DAT0- B- 4 SDA GND
10
DAT1+ G+ 4
9 M24C02WMN6
DAT1- G- 4
2
DAT2+ R+ 4
1
DAT2- R- 4
13
DAT3+ 12
DAT3- 5
DAT4+ 4
DAT4- 21
DAT5+ 20
DAT5- 23
clk+ CLK+ 4
24
clk- CLK- 4
3
VCC5V
Title
2
TSU16AK
Size Document Number Rev
B INPUT D
Date: Tuesday, November 09, 2004 Sheet 3 of 6
20
2 VCC3.3 2 VCC2.5
600 OHM 600 OHM
C405 + C414 +
10uF/16V 10uF/16V
VAD VPLLVDVI VDPLL VPO VDD
C406C407C408C409C410C411C412C413 C415C416C417C418
0.1uF0.1uF0.1uF0.1uF0.1uF0.1uF0.1uF0.1uF 0.1uF0.1uF0.1uF0.1uF
104
114
126
117
55
65
35
45
51
53
11
21
84
94
18
87
97
U401
AVDD_PLL
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
AVDD
AVDD
AVDD_MPLL
VDDC
VDDC
VDDC
VDDC
AVDD_DVI
AVDD_DVI
102 PA0
63 LVA3P 103 PA1
3 RIN RIN0 LVA3M
62 106 PA2
3 GNDR RIN0M LVACKP
60 107 PA3
3 GIN GIN0 LVACKM
59 108 PA4
3 GNDG GIN0M LVA2P
61 109 PA5
3 SOG SOGIN0 LVA2M
58 110 PA6
3 BIN BIN0 LVA1P
57 111 PA7
3 GNDB BIN0M LVA1M
37 112 PA8
3 HSYNC HSYNC0 LVA0P
38 113 PA9 VAA1 FB403 VAD
3 VSYNC VSYNC0 LVA0M PA[0..9]
29
DDC1_CLK/GPO8 PA[0..9] 5
28
DDC1_DAT/GPO7 2 VAA1
600 OHM
C419 +
3 R+ 40 10uF/16V
41 R+
3 R- R-
3 G+ 43 C420C421
44 G+ 118 PB0 0.1uF0.1uF
3 G- G- NC/LVB3P PB[0..9]
46 119 PB1
3 B+ B+ NC/LVB3M PB[0..9] 5
47 120 PB2
3 B- B- NC/LVBCKP
49 121 PB3
3 CLK+ CK+ NC/LVBCKM
50 122 PB4
3 CLK- CK- NC/LVB2P
52 123 PB5
VDVI REXT NC/LVB2M PB6
R403 390 1/16W 124
NC/LVB1P 125 PB7
NC/LVB1M 128 PB8 VAA2 FB404 VPLL
NC/LVB0P 1 PB9
66 NC/LVB0M
REFP 2 VAA2
C401 600 OHM
TSU16AK
0.1uF 67 C422 +
REFM 10uF/16V
C423
0.1uF
6 CSZ 69
71 CSZ
6 SCL SCL
6 SDA 70
32 SDA VAA3 FB405 VDVI
6 HWRESET HWRESETZ
72 VCC5V
6 INT INT
2 VAA3
600 OHM
C402 22pF 33 30
XIN ADO/NC AD0 6
77
AD1/NC AD1 6
X401 78 R402
AD2/NC AD2 6
31 VAA4 FB406 VDPLL
AD3/NC AD3 6 100 1/16W
14.318MHz
34
XOUT 2 VAA4
C403 22pF 6 600 OHM
BUS TYPE/NC
C404 0.1uF 3 C427 +
2 BYPASS R401 10uF/16V
AVSS_LPLL NC
AVSS_MPLL
AVSS_PLL
C428
AVSS_DVI
AVSS_DVI
AVSS_DVI
0.1uF
GNDC
GNDC
116 GNDC
GNDC
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
AVSS
AVSS
AVSS
R401 R402
36
54
39
42
48
10
20
85
95
19
86
96
21
PA[0..9]
4 PA[0..9] PA0 LVA3P
PA1 LVA3M CN503
PA2 LVACKP
PA3 LVACKM LVB0M RXO0- 1 2 RXO0+ LVB0P
PA4 LVA2P LVB1M RXO1- 3 4 RXO1+ LVB1P
PA5 LVA2M LVB2M RXO2- 5 6 RXO2+ LVB2P
LVBCKM RXOC- 7 8 RXOC+ LVBCKP
PA6 LVA1P LVB3M RXO3- 9 10 RXO3+ LVB3P
PA7 LVA1M LVA0M RXE0- 11 12 RXE0+ LVA0P
LVA1M RXE1- 13 14 RXE1+ LVA1P
PA8 LVA0P LVA2M RXE2- 15 16 RXE2+ LVA2P
PB[0..9] PA9 LVA0M LVACKM RXEC- 17 18 RXEC+ LVACKP
4 PB[0..9] PB0 LVB3P LVA3M RXE3- 19 20 RXE3+ LVA3P
PB1 LVB3M 21 22
PB2 LVBCKP 23 24
PB3 LVBCKM
PB4 LVB2P
PB5 LVB2M CONN R502
PB6 LVB1P
PB7 LVB1M 0 1/16W
PB8 LVB0P VLCD
PB9 LVB0M
VLCD 2
C509
+ C510 C511
Title
TSU16AK
Size Document Number Rev
A PANEL INTERFACE D
Date: Wednesday, April 14, 2004 Sheet 5 of 6
22
2 VCPU
8
7
6
5
8
7
6
5
RN601
R601 R602 C601 RN602
10K 1/16W
10K 1/16W 0.1uF 10K 1/16W
10K 1/16W
1
2
3
4
1
2
3
4
C602 22pF
44
U601
X601 35 43 POWER
EA/VP P0.0
VCC
42 ENTER
21 P0.1 41 RIGHT
+ C603 20MHz XTAL1 P0.2 40 LEFT
VCPU 10uF/16V P0.3 39 AUTO
U603 MAX810STR 20 P0.4 38 LED_B
C604 22pF XTAL2 P0.5 37 LED_O
3 2 10 P0.6 36 LED_G
VCC RST RESET P0.7
GND
24 R636 0 1/16W
P2.0 HWRESET 4
D601 R603 12 25
P4.3 P2.1 onPANEL_5V/3.3V 2
14 26
4 INT INT0/P3.2 P2.2 onBACKLITE 2
LL4148-GS08 10K 1/16W 15 27
1
9 11 R611 NC
P1.7 P3.0/RXD DDC_CLK 3
AT24C16N-10SC-2.7 R638 NC R634 100 1/16W
TXD 3
R615 10K 1/16W W78E65P-40 R635 100 1/16W
RXD 3
22
NC
1
Volume 4 VCPU
R641 NC
VCPU VCPU
2
LED_GRN 3 4 LED_ORANGE
3
CONN Title
TSU16AK
Size Document Number Rev
B MPU D
Date: Wednesday, July 21, 2004 Sheet 6 of 6
23
NR901
t
R920 C920
47 1/2W 0.001uF/500V
4
NTCR
BD901
2KBP06M T901 F902
+
D901
FR107 7
6 GND
C903 0.47uF/250V R907 R905
5 GND
1M 1/4W 470K 1/4W D902 3 7,8
PS102R L904 4 5V
3 5VA
5 D912 + + DIM
31DQ06 C925 C926 2
1 ON/OFF
C913 + R908 1000uF/16V 470uF/16V
0.001uF/160V C908 C907 10 1/16W 10,11 FB902
2
R931
4
1K 1/16W
IC902
PC123FY2 4P
R927
R909 1K 1/10W
3
39 1/4W
F901 R910
FUSE 82K 1/10W
IC904 C936 R924 R925
C901 C902 H431BA 0.1uF R929 33K 1/10W 3.6K 1/10W
0.001uF/160V 0.001uF/160V 3.9 1/16W
IC903
HTL431
R911
R928
C910 100K 1/10W
1K 1/10W
1uF/25V
C935 R926
0.01uF 24K 1/10W
3
2 1
CN901 CN301
SOCKET 1 CN302
4
3 3 INR
2 2 GND
5 1 INL
PHONEJACK
CONN
<Title>
POWER
Size Document Number Rev
B 1
24
1 1
1
C215 CN201
22pF/6KV
1
2
Q203 L201
L
1 8 3
+12V
2 7
3 6
4 5 D201 R224 R225 R226 R227
+ C201 + C223 R212 D203 1.5K 1.5K 1.5K 1/4W 1.5K 1/4W
150uF/25V 150uF/25V C202 C225 3.9K SR24 RLZ11B C216
Q202 1uF/25V R214 SI4431DY-T1 22pF/6KV
0.1uF/25V 2.2K 1/16W 5 PT201 9
DTA144WKA
R220 C213 3,4
R243 Q205 15K 0.22uF/160V
Q201 1K 1/4W R216 C211 2
NO/OFF MPS3904 220 1/16W 1uF/25V 6
DTC144WKA
2
R201 R202 1 7
30 K 10K 1 1 R232
R218 R222 POWER X'FMR 1K
DIM
2
3
C203 R208 R210 MPS3906 D209 D205
1uF/25V 4.7K 1/16W 15K 1N4148
3
1N4148
R205
47K
C209 R240 D207 R234
1uF/25V 51K 1N4148 910 1/4W
C205
0.1uF
C221 R238 C219 R236 TP5 TP6
0.47uF/63V 12K 1uF/25V 620 HVL HVL
1 1
15
14
13
12
11
10
33uF NC HVO
C204
2FBK
SCP
2IN+
Vcc
2OUT
2IN-
REF
2DTC
1
U201 L 1
1OUT
1DTC
1FBK
GND
1IN+
1IN-
TL1451ACNSR 1 8
CT
RT
2 7 2
C206 3 6
0.1uF 4 5 D202 R228 R229 R230 R231
1
330pF R204
10K R209 1 7
4.7K 1/16W 1 1 R233
R203 R219 POWER X'FMR 1K
2
R211
15K
Title
is power GND FOR SAMSUNG M170EU-L01 INVERTER
Size Document Number Rev
C 2
Monday, July 04, 2005
is signal GND Date: Sheet 2 of 2
25
+12V
12V
PIN-3 CN202
WAFER 2*7P 2.54mm MUTE
13 14
PIN-1 11 12
9 10 + +
VOLUME 7 8 C201 C202 C203
5 6 470uF/16V 470uF/16V 0.1uF
3 4
1 2
GND U201
PIN-1
STANDBY
TDA7496L GND
16
15
8
C204 0.47uF
+
1 R201 10K 4 17 4
2 INL OUTL 470uF/16V 3
3 C206 0.47uF 9 14 2
+
INR OUTR
R203 10K 1
R212 6 10 C207
33L8022-3A-H FEMALE VOLUME SVR 470uF/16V
220K 11 7 WAFER 4P2.0 R/A
STBY VAROUT_R
12 5 R207 R208 GND
MUTE VAROUT_L
1K
1K
GND R210 R211
GND
GND
GND
GND
GND
GND
GND
C211 C212 +
5.6K
5.6K
26
27
28
29
30
31
32
No power
NG
NG
Replace X601, X401
OK
Replace U601
NG
Replace U401
33
No picture
OK
OK
Check reset circuit of NG Check Correspondent
component
U601 is normal
Measure U201 PIN2=2.5V
U202 PIN2=3.3V OK
Replace U601
OK
X401 oscillate NG
waveform is normal
Replace U201, U202
NG
OK
Replace X401
NG Check Correspondent
OK
component
Replace U401
34
White screen
NG
Measure Q204 base X601 oscillate
waveform is normal
is high level?
OK NG Replace X601
OK
NG Check Correspondent
Check Correspondent NG
component.
component.
OK
OK
Replace U601
Replace PANEL
35
36
NG
Check adapter or MB
OK
NG
Check Interface board
OK
NG
Change Q201 or Q202
OK
NG
Change U201
OK
Check D201 (-),D202 (-) have the output of square wave at short time.
NG
Check Q203/Q209/Q210/D201, Q204/Q211/Q212/D202
OK
NG
Check Q209/Q210/C213,Q211/Q212/C214
OK
NG
Change PT201/PT202
OK
37
NG
Is Key Pad Board connecting normally? Connect Key Pad Board
OK
NG
Is Button Switch normally? Replace Button Switch
OK
NG
Is Key Pad Board normally? Replace Key Pad Board
OK
38
Turn on power, press the MENU button, pull out the power cord, and then plug the power cord. Then the factory
OSD will be at the left top of the panel.
4. Bias adjustment:
5. Gain adjustment:
Move cursor to “-F-” and press MENU key
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53