Professional Documents
Culture Documents
Service
Service
Service
Horizontal Frequency
30-83 KHz
Table of Contents
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
T8AJNY2BZ3K2NNF.LF
T8AJNY2QZ3E6NNF.LF
2
Downloaded from www.Manualslib.com manuals search engine
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
3
Downloaded from www.Manualslib.com manuals search engine
1. Monitor Specifications
4
Downloaded from www.Manualslib.com manuals search engine
2. LCD Monitor Description
The LCD MONITOR will contain a main board and a key board which house the flat panel control logic, brightness
control logic and DDC.
D-SUB
Signal
Adapter
AC-IN
100V~24
5
Downloaded from www.Manualslib.com manuals search engine
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control knobs are located at base of the monitor. By
changing these settings, the picture can be adjusted to your personal preferences.
Power
Press the Power button to turn 0n/off the monitor.
Eco Mode / <
Press the Eco key continuously to select the Eco mode of brightness when there is no OSD ( Eco mode hot key may
not be available in all models).
4:3 or wide image ratio / >
When there is no OSD, press > hotkey continuously to change 4:3 or wide image ratio. (If the product screen size is
4:3 or input signal resolution is wide format, the hot key is disable to adjust. )
Auto/Exit
When the OSD is closed, press Auto/Source/Exit button continuously about 2 second to do auto configure (only for
the models with dual or more inputs).
When the OSD is closed, press Auto/Source/Exit button will be Source hot key function(Only for the models with
dual or more inputs).Press Auto/Source/Exit button continuously to select the input source showed in the message
bar, press Menu/Enter button to change to the source selected.
6
Downloaded from www.Manualslib.com manuals search engine
3.3 OSD Menu
Notes:
1) If the product has only one signal input, the item of "Input Select" is disable to adjust.
2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disable to
adjust.
3) One of DCR, Color Boost, and Picture Boost functions is active, the other two function is turned off accordingly.
7
Downloaded from www.Manualslib.com manuals search engine
8
Downloaded from www.Manualslib.com manuals search engine
9
Downloaded from www.Manualslib.com manuals search engine
10
Downloaded from www.Manualslib.com manuals search engine
11
Downloaded from www.Manualslib.com manuals search engine
12
Downloaded from www.Manualslib.com manuals search engine
13
Downloaded from www.Manualslib.com manuals search engine
14
Downloaded from www.Manualslib.com manuals search engine
15
Downloaded from www.Manualslib.com manuals search engine
16
Downloaded from www.Manualslib.com manuals search engine
17
Downloaded from www.Manualslib.com manuals search engine
4. Input/Output Specification
4.1 Input Signal Connector
Analog connector
18
Downloaded from www.Manualslib.com manuals search engine
4.3 Panel Specification
4.3.1 General Features
LM185WH2-TRA2 is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED)
backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type
display operating in the normally white mode. It has a 18.5 inch diagonally measured active display area with HD
resolution (768 vertical by 1366 horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or
dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a
8-bit gray scale signal for each dot, thus, presenting a palette of more than 16,7M colors with Advanced-FRC(Frame
Rate Control). It has been designed to apply the interface method that enables low power, high speed, low EMI. FPD
Link or compatible must be used as a LVDS(Low Voltage Differential Signaling) chip. It is intended to support
applications where thin thickness, wide viewing angle, low power are critical factors and graphic displays are
important. In combination with the vertical arrangement of the sub-pixels, the LM185WH2-TRA2 characteristics
provide an excellent flat panel display for office automation products such as monitors.
4.3.2 Display Characteristics
19
Downloaded from www.Manualslib.com manuals search engine
4.3.3 Optical Characteristics
Electrical characteristics
Ta = 25°C
20
Downloaded from www.Manualslib.com manuals search engine
4.3.4 Optical Characteristics
(Ta= 25°C, VLCD=5.0V, fv=60Hz, DCLK= 77.0MHz, Is=60mA)
21
Downloaded from www.Manualslib.com manuals search engine
5. Block Diagram
Main Board
H sync
EEPROM
V sync
M24C02
RGB
(U101)
D-Sub
Connector
(CN101)
MOSFET
(Q806)
PWM Control
Feedback Circuit ON/OFF
MP3389EF
(U801) DIM
22
Downloaded from www.Manualslib.com manuals search engine
6. Schematic
6.1 Main Board
715G4134M01000004F
2010/4/2
FB102
VCC3.3
CMVCC1 DSUB_5V
1
R133
390K +/-5% 1/16W D101
BAV70
3
100K 1/16W
CMVCC1
FB104 FB105 DVI_5V
3,4,5 CMVCC1
2
C117
R136 NC/220N16V
R137 R138 NC/22K 1/16W
NC/4.7K 1/16W NC/4.7K 1/16W U102
8 1
7 VCC A0 2
DDC2_SCL 6 WP A1 3
DDC2_SDA 5 SCL A2 4
SDA VSS
5 DDC_WP
NC/CAT24C02WI-GT3
23
2 1
PA[0..9] PB[0..9] 4 3
5 PA[0..9] 5 PB[0..9] PB0 LVB3P LVB0M RXO0- 6 5 RXO0+ LVB0P
PA0 LVA3P PB1 LVB3M LVB1M RXO1- 8 7 RXO1+ LVB1P
PA1 LVA3M PB2 LVBCKP LVB2M RXO2- 10 9 RXO2+ LVB2P
PA2 LVACKP PB3 LVBCKM LVBCKM RXOC- 12 11 RXOC+ LVBCKP
PA3 LVACKM PB4 LVB2P LVB3M RXO3- 14 13 RXO3+ LVB3P
PA4 LVA2P PB5 LVB2M LVA0M RXE0- 16 15 RXE0+ LVA0P
PA5 LVA2M PB6 LVB1P LVA1M RXE1- 18 17 RXE1+ LVA1P
PA6 LVA1P PB7 LVB1M LVA2M RXE2- 20 19 RXE2+ LVA2P
PA7 LVA1M PB8 LVB0P LVACKM RXEC- 22 21 RXEC+ LVACKP
PA8 LVA0P PB9 LVB0M LVA3M RXE3- 24 23 RXE3+ LVA3P
PA9 LVA0M SDA_PANEL 26 25 SCL_PANEL
5 SDA_PANEL 28 27 SCL_PANEL 5
30 29
2010/2/26 2010/2/26
CONN PANEL_VCC
1 2
120 OHM
C302
22UF 16V
CMVCC1
2,4,5 CMVCC1
R305
5
6
7
8
10K+-5%1/16W
R306 Q301 U301
D
D
D
D
AO3401A
NC/AO4411
100K 1/16W
G
S
S
S
CMVCC1
R304 C303
4
3
2
1
R303 C304
4.7K 1/16W 100N 16V
3D
C305 R308
1uF 16V NC/10K+-5%1/16W
1 2
G S
AO3401L
24
VOUT(TAB)
ADJ(GND)
1
VIN
D707
SR34
2
3
2
1
1
D708
SR34 SOT 223
VCC3.3
2
U701
3 2
Dropout voltage must
VI
GND
VO
< 0.8V @ 600mA
C708 C709 C707
1
R702
10K+-5%1/16W SOT 223
R703 D703
7 BKLT-EN
BKLT-EN 10K+-5%1/16W SR34 Dropout voltage must
U704
2
C702 Q701 3 2
< 0.8V @ 400mA
100N 16V LMBT3904LT1G VI VO
1
GND
on_BACKLIGHT 5
R704 22K 1/16W D704
SR34
1
2
SOT 252
VCC1.8
U703
NC/AZ1117D-1.8-E1
3 2
IN OUT
CMVCC1
GND
R705
10K+-5%1/16W
R706
BKLT-VBRI
7 BKLT-VBR1 adj_BACKLIGHT 5
100OHM1/16W
2010/1/25
C713 FB703
100N 16V 0R05 1/10W
CMVCC1
9
8 Thermal Pad 1 L701 22UH
7 BST SW 2 CMVCC1 2,3,5
6 VIN EN 3
5 FREQ COMP 4
R712 GND FB
100K 1/16W
2
U705 MP1584EN
R713 C714
D701 C710 C711 6.8K +-1% 1/16W 1N 50V
SR34 1N 50V 1N 50V
1
0402=>0603
2010/3/4 2010/3/8
2
+12V
Precision Issue Cancel FB702,EMI OK
2010/4/24
+12V 6,7
FB701
CN701
1 2 3
BEAD
2
0402=>0603 1
2010/3/4
+
C720 C718 C715 C719 JACK
10uF 25V 180uF 16V 1N 50V 100N 50V
25
116
300OHM DVDD
45
43
52
26
15
17
28
51
90
53
U401
6
2
R414 26
AVCC 470R 1/16W 1% C405
CVDD_ZP
ADC_VAA18
ADC_BIAS
ADC_VAA33
DVDD_ZP
PLL_DVDD
PLL_GND
CVDD
CVDD
AVCC
AVCC
DVDD
DVDD
DVDD
NC
2 51 53 90 116 16 100 C404
C417 C418 C419 C437 C438 REXT DGND/CGND 99 4.7UF 10V 100N 16V
C416 RX2+ 4 DGND/CGND 98 C0805
2 RX2P RX2- 5 RX2+ DGND/CGND 97
4.7UF 10V 100N 16V 100N 16V 100N 16V 100N 16V 100N 16V
2 RX2N RX1+ 7 RX2- DGND/CGND 96
C0805
2 RX1P RX1- 8 RX1+ DGND/CGND 95
FB406
2 RX1N RX1- DGND/CGND
NC/300OHMADC_VAA33 RX0+ 10 94
2 RX0P RX0- 11 RX0+ DGND/CGND 93
2 RX0N RXC+ 13 RX0- DGND/CGND 92
28 2 RXCP RXC- 14 RXC+ DGND/CGND 91
2 RXCN RXC- DGND/CGND PA0
C421 C422 88 PB9 PA1
4.7UF 10V 100N 16V AHS0 41 T0M 87 PB8 PA2
2 DSUB_H AVS0 42 HSY NCI1 T0P 86 PB7 PA3
C0805
2 DSUB_V VSY NCI1 T1M 85 PB6 PA4
FB407 B0+ 19 T1P 84 PB5 PA5
ADC_BIAS 2 DSUB_B+ B0- 20 BIN1+ T2M 83 PB4 PA6
300OHM
2 DSUB_B- BIN1- T2P 82 PB3 PA7
SOG_DET 21 TCLK1M 81 PB2 PA8
17 2 DSUB_SOG G0+ 22 SOG1I TCLK1P 80 PB1 PA9
2 DSUB_G+ G0- 23 GIN1+ T3M 79 PB0
2 DSUB_G- GIN1- T3P 77 PA9
C423 C424
4.7UF 10V 1uF 16V R0+ 24 T4M 76 PA8
2 DSUB_R+ R0- 25 RIN1+ T4P 75 PA7
C0805
2 DSUB_R- RIN1- T5M 74 PA6
T5P 73 PA5 PA[0..9]
FB410 VCC33 T6M PA[0..9] 3
72 PA4
300OHM T6P 71 PA3
TCLK2M 70 PA2 PB0 PB[0..9]
TCLK2P 69 PA1 PB1 PB[0..9] 3
T7M 68 PA0 PB2
C408 T7P PB3
1N 50V CMVCC1 PB4
2010/6/2 PB5
62 PB6
DDCSDA2 34 VCKI 61 PB7
2 DDC2_SDA DDCSCL2 35 PB7/DDC_SDA1* V7 60 PB8
2 DDC2_SCL DDCSDA1 46 PB6/DDC_SCL1* V6 59 PB9
R415
2 DDC1_SDA DDCSCL1 47 PB5/DDC_SDA0* V5 58
R416 100K 1/16W
2 DDC1_SCL PB4/DDC_SCL0* V4 57
220K 1/16W 5%
5V_DET 30 V3 56
DET_CABLE 33 PB3/ADC3/INTE1 V2 55
2 DET_CABLE PB2/ADC2/INTE0 V1
KEY 1 R436 100OHM1/16W 125 54
KEY 2 R437 100OHM1/16W 126 PB1/ADC1 V0
C425 100N 16V PB0/ADC0
For touch key VCC3.3 VCC3.3
SPI_CE 104
SPI_SO 105 SPI_CE 113
SPI_SI 106 SPI_SO INT_VSO 114
SPI_CK 107 SPI_SI INT_HSO R419 R420
WP 108 SPI_CLK 117 adj_BACKLIGHT NC/10K+-5%1/16W NC/10K+-5%1/16W
48 PD4 PWMA* 118 Volume adj_BACKLIGHT 4
29 PD5 PWMB* Volume 6
DDC_WP R435
2 DDC_WP PD6 103
100OHM1/16W R417 NC/100OHM1/16W
PC7 102 DET_VGA 2
PC6 124 on_BACKLIGHT DET_DVI 2
R418 NC/100OHM1/16W
PC5 123 LED_GRN/BLUE on_BACKLIGHT 4
49 PC4/PWM1 122 LED_ORANGE
50 P35 PC3/PWM0 110
31 P34 PC2 121 R426 NC/100OHM1/16W POWER_KEY #
DVDD 32 P31/TXD PC1* 120 AUDIO_MUTE
P30/RXD PC0* AUDIO_MUTE 6
1 2010/2/23 reserve
RSTB 40
R403 C426 47pF 50V 127 PA7/PWM9* 39
2
DGND/CGND
DGND/CGND
DGND
DGND
PGND
AGND
AGND
VCC3.3
GND
GND
DVDD
NT68628
44
3
109
64
78
101
18
12
9
27
89
63
112
111
NC/3.9K1/16W
NC/3.9K1/16W
NC/3.9K1/16W
C429 R431 R432 R433 2010/2/23
220N16V key bd have pull
U402 2010/3/3 hight resistor
SPI_CE 1 8
SPI_SO 2 CE# VDD 7
WP R401 100OHM1/16W 3 SO HOLD# 6 SPI_CK 2010/2/23
4 WP# SCK 5 SPI_SI CMVCC1 VCC3.3 CMVCC1 VCC3.3
GND SI
R402 Pm25LD020C-SCE
2,3,4 CMVCC1 CN401
10K+-5%1/16W R407
2010/2/2 NC/0R05 1/16W
R406 7 KEY 1
NC/0R05 OHM R408 R409 6 KEY 2
NC/0R05 OHM 0R05 OHM 5 POWER_KEY #
4 LED_G
3 LED_R ZD401 ZD402 ZD403
2
1 C431 C432 C433 C434 C435
NC/RLZ5.6B
NC/RLZ5.6B
NC/RLZ5.6B
R411
100N 16V
100N 16V
NC/100N 16V
NC/100N 16V
NC/100N 16V
R412
Q401 1 LED_GRN/BLUE
NC/LMBT3906LT1G 100OHM1/16W
3
R421
2
LED_R R405
0R05 1/10W C436 FB409
100N 16V
1 2 LED_R
NC/120 OHM
11/30/2009
26
8
7
6
5
1 MP3389EF 28 C803 C813
2 NC NC 27 C807
C801 0.47uF 16V Q806 +
D1
D1
D2
D2
3 VIN VFAULT 26 C805 0.47UF 50V 2N2 50V
C802 68NF 50V 4 VCC GATE 25 APM8005KCTRG 4.7UF 100V
G1
G2
S1
S2
R806 1K 1/10W 5 COMP PGND 24 100pF 50V
4 BKLT-EN 6 EN ISENSE 23
OVP
1
2
3
4
C812 100N 50V 7 DBRT OVP 22 C809
GND LED1 R805
2010/3/4 8 21 C804 C814
OSC LED2 300K 1/8W
R807 20K 1/10W 9 20 100pF 50V
10 ISET LED3 19 0.47UF 50V 2N2 50V
R808 1K 1/10W 11 BOSC LED4 18 R841 R842
4 BKLT-VBR1 12 LED12 LED5 17 2.2 OHM 1/10W 2.2 OHM 1/10W
R810 20K 1/10W 13 LED11 LED6 16
14 LED10 LED7 15
E-Pad
R833 R832
LED9 LED8 NC/0R01 1/10W 0R05 1/10W
OVP
R834 R809
29
11
CN803
R804 100K 1/10W R840 R836
0R05 1/10W 0R05 1/10W R827 1R 1/10W 5% 1
2
R828 1R 1/10W 5% 3
4
5
18.5" 20" 21.5" 23" 6
2010/3/4 R831 1R 1/10W 5%
7
R832 0 ohm 0 ohm NC NC 8
R829 NC/1R 1/10W 5%
9
R833 NC NC 0 ohm 0 ohm 10
R830 1R 1/10W 5%
R836 0 ohm 0 ohm NC NC
R839 NC NC 0 ohm 0 ohm CONN
12
R840 0 ohm 0 ohm NC NC
R827 1 ohm 1 ohm 1 ohm 1 ohm
R828 1 ohm 1 ohm 1 ohm 1 ohm
R829 NC NC 1 ohm 1 ohm
R830 1 ohm 1 ohm 1 ohm 1 ohm
R831 NC NC NC NC
R803 51K 51K 51K 51K
R819 30K 30K 10K 10K
R809 7.15K 6.04K 7.15K 6.2K
R834 75K NC 75K 75K
T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL AOC Size Custom
R812 0.15 ohm 0.15 ohm 0.1 ohm 0.1 ohm
絬隔瓜絪腹 G4134-M0D-000-0040-6-100613 TPV MODEL e943Fws Rev B
R816 NC NC NC NC
Key Component 7.0.CONVERT PCB NAME
称爹
Date Sunday , June 13, 2010 Sheet 7 of 7
27
KEY 0.1524
THD
GPIO_02
GPIO_03
GPIO_04
V3.3
25
24
23
22
21
20
19
AC_SHIELD U001
THD1
GPIO2
GPIO3
GPIO4
DVSS
E-PAD
NC
8
CIN_04 4 15 SM_CLK
CIN_07 5 CIN4 SCLK 14 GPIO_09 SM_CLK R005 0R05 1/16W CLK 1
CIN_09 6 CIN7 GPIO9 13 5V_LED V3.3 SM_DATA R006 0R05 1/16W DATA 2
CIN9 DVCC THD 3
VSHILD
C008
GPIO11
TP2
VBIAS
CIN11
AVCC
SM_INT# 4
AVSS
9
AC_SHIELD
C011 ZD001
GPIO_11
VBIAS
1
V3.3
V3.3
C007
100nF 25V
C006 C005
100nF 25V 100nF 25V
5V_LED
1
LED
2
T2 KEY 0.1524
C013 CIN_09
1uF Z 10V
GPIO_11
GPIO_03
GPIO_07
GPIO_04
GPIO_02
GPIO_09
T1 KEY 0.1524
CIN_02
-_2 KEY 0.1524 +_3 KEY 0.1524 PWR_1 KEY 0.1524 AUTO_4 KEY 0.1524 MENU_5 KEY 0.1524
CIN_01 CIN_03 CIN_04 CIN_07 CIN_11
TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL AOC e943Fw Size A3
28
29
31
32
No power
OK
NG
Check Power “On/Off”
Turn on the Power “On/Off” switch
is “On”?
OK
OK
NG
33
NG
Press the power
Replace the main board
button is OK?
OK
OK
Replace the main
The end
board and connection
NG
OK
Check the LVDS/FFC Replace the LVDS/FFC
cable or panel cable or panel
NG
34
OK
Reset in factory mode The end
NG
NG
OK
Readjust the phase and pixel
The end
clock in the user mode
NG
NG NG
OK
Replace the main board The end
NG
OK
35
OK
36
Turn off the power, press two direction keys and turn the power on. Then press the “MENU” button. The factory OSD
will appear.
4. Gain adjustment:
Move cursor to “-F-” and press MENU key
37
38
39
40
41
S-24CL04A0I-T8T1GE, SEIKO
U2 0ISKL-0001A INSTRUMENTS, 4K, 4MS (TYP), TSSOP,
R/TP, 8
42
45
47
48
49
51