Professional Documents
Culture Documents
Vector HP DGPS Man PDF
Vector HP DGPS Man PDF
DGPS
Transmitter
Nautel Limited
10089 Peggy's Cove Road,
Hackett's Cove, NS, Canada B3Z 3J4
T.877 6 nautel (628835) or +1.902.823.2233
F.+1.902.823.3183 info@nautel.com
e-mail: support@nautel.com
www.nautel.com
Nautel Limited/Nautel Incorporated, hereinafter referred to as Nautel, guarantees all mechanical and electrical parts of
the equipment for a period of thirteen months from date of shipment.
1. A "Part Failure" shall be deemed to have occurred when the part has become defective, or does not have the
characteristics required for the specified equipment performance:
(a) When the equipment is operated within the design parameters, and
(b) When the equipment is installed and adjusted according to Nautel's prescribed procedures as stated in
the instruction manual.
2. Nautel shall provide replacements for all "Parts" at no cost to the Customer when they become defective during
the warranty period, and upon the return of the defective part.
3. In the event that a "Part" fails during the warranty period and causes damage to a sub-assembly that cannot be
readily repaired in the field, the entire sub-assembly so damaged may be returned to Nautel for repair. The
repairs will be made without charge to the Customer.
4. Where warranty replacements or repair are provided under items 2 or 3, Nautel will pay that part of the shipping
costs incurred in returning the part/assembly to the Customer.
5. Warranty replacement parts and repair, which are provided under items 2 or 3, shall be guaranteed for a period
of ninety days from date of shipment or until the end of the original warranty period, whichever occurs later.
6. Nautel will not assume responsibility for any charges incurred by other than Nautel employees.
7. Nautel shall have the privilege of investigating whether failures have been caused by factors beyond its control.
8. Nautel shall in no event be liable for any consequential damages arising from the use of this equipment.
9. When requesting a warranty repair/replacement, please provide complete and accurate information. Observe
the instructions regarding 'Equipment Being Returned to Nautel' on page two of this warranty and provide the
information requested.
10. When ordering spare/replacement parts, please provide complete and accurate information. Refer to the parts
list of the Repair manual for ordering information. Provide as much of the information requested for 'Equipment
Being Returned to Nautel' on page two of this warranty as is practical. The information identified by an asterisk
is the minimum required.
U.S.A. customers use: Nautel Incorporated T. +1.207.947.8200 (24 hours) or 877 6 nautel (628835)
201 Target Industrial Circle F. +1.207.947.3693
Bangor, Maine 04401
All other customers use: Nautel Limited T. +1.902.823.3900 (24 hours) or 877 6 nautel (628835)
10089 Peggy’s Cove Road, F. +1.902.823.3183
Hackett’s Cove, NS, Canada E-Mail support@nautel.com
B3Z 3J4 Web www.nautel.com
Obtain an RMA number from Nautel (you must have an RMA number to return equipment)
Mark the item as 'field return'
Mark the item with the RMA number assigned by Nautel
Address the item to the appropriate Nautel facility
Complete and accurate information regarding the equipment being returned will ensure prompt attention and will
expedite the dispatch of replacements. Refer to the nameplate on the transmitter and/or the appropriate
module/assembly to obtain name, type, part and serial number information. Refer to the parts list of this manual or the
appropriate service instruction manual for additional ordering information.
* Model of Equipment
* Serial number of Equipment
* Name of Part/Assembly
Serial number of Part/Assembly
* Complete reference designation of Part/Assembly
* Nautel's part number of Part/Assembly
* OEM's part number of Part/Assembly
Number of hours in Use
Nature of defect
* Return shipping address
GROUND (EARTH)
ELECTROSTATIC SENSITIVE
There are devices used in this equipment containing beryllium oxide ceramic,
which is non-hazardous during normal device operation and under normal device
failure conditions. These devices are specifically identified in the equipment parts
list(s) by including ‘BeO’ in the part’s description.
DO NOT cut, crush or grind devices because the resulting dust may be
HAZARDOUS IF INHALED. Unserviceable devices should be disposed of as
harmful waste.
3 OPERATING INSTRUCTIONS
6 THEORY OF OPERATION
6 THEORY OF OPERATION
8 WIRING INFORMATION
9 ELECTRICAL SCHEMATICS
10 MECHANICAL DRAWINGS
List of Tables
1-1 Recommended Site Test Equipment 1-3
1-2 Glossary of Terms 1-4
2-1 Forced Air Exchange Rate 2-1
2-2 Ac Power Consumption 2-5
2-3 Dc Power Consumption 2-6
2-4 ATU Serial Interface 2-13
2-5 RS-422 Remote Interface 2-13
2-6 RS-232 Remote Interface 2-13
2-7 Ac Power Connection 2-14
2-8 Dc Power Connection 2-15
2-9 RF Filter PWB Tap Settings vs Frequency 2-16
3-1 Front Panel – System Diagram Controls and Indicators 3-5
3-2 Front Panel – Control Section Controls and Indicators 3-7
3-3 Exciter Interface PWB Controls and Indicators 3-9
3-4 Remote Interface PWB Controls and Indicators 3-11
3-5 Miscellaneous Exciter/Control Assembly Controls and Indicators 3-12
3-6 Miscellaneous RF Power Block Controls and Indicators 3-13
3-7 Ac Power Distribution Assembly Controls 3-15
3-8 Dc Power Distribution Assembly Controls 3-17
3-9 Events Log Displays – Non Alarm Events 3-21
5-1 Troubleshooting and Replacement Tips 5-5
7-1 Manufacturer’s Index 7-4
8-1 Wiring Lists Provided 8-1
9-1 Electrical Schematics 9-3
10-1 Mechanical Drawings 10-2
List of Figures/Drawings
2-1 Vector Transmitter Environment Considerations 2-3
2-2 Customer Interface to Vector Transmitter 2-4
2-3 Single Ended Input Selected 2-7
2-4 Differential Input Selected 2-8
2-5 Removing Packing Support Bars 2-12
2-6 Block Diagram – Recommended Low Power Transmitter
System Installation 2-18
2-7 Block Diagram – Recommended High Power Transmitter
System Installation 2-19
3-1 Vector Transmitter Front Panel (Primary User Interface) 3-3
3-2 Vector Transmitter Front Panel – System Diagram Section 3-4
3-3 Vector Transmitter Front Panel – Control Section 3-6
3-4 Part of NAPI76 Exciter Interface PWB A2A2 3-8
3-5 Part of NAPI78A Remote Interface PWB A2A3 3-10
3-6 NAX233/01, /02 & /04 Ac Power Distribution Assembly A8 (Rear View) 3-14
3-7 NAX235/01 & /02 Dc Power Distribution Assembly A7 3-16
3-8 Diagnostic Display – Meters Screen 3-18
3-9 Diagnostic Display – Main Menu 3-18
3-10 Flow Diagram – Diagnostic Display Functions 3-19
4-1 Exciter/Control Assembly A2 4-2
6-1 Vector Series DGPS Transmitter 6-3
6-2 Block Diagram – Exciter Control/Monitor Stage 6-9
6-3 Timing Diagram for PDM Differential Amplifier 6-11
6-4 Block Diagram – RF Power Block 6-19
6-5 Block Diagram – RF Power Module 6-21
6-6 Simplified Principles of Class ‘D’ Operation 6-24
7-1 Family Tree – Vector DGPS Transmitter 7-5
7-2 Family Tree – RF Power Block 7-6
TERM DESCRIPTION
ac Alternating current
AM Amplitude modulation
Bit Basic timing increment derived from master clock in keying unit.
Length is dependent on frame length and number of characters
used. An 8-bit frame is nominally 125 ms long.
dc Direct current
Hz Hertz
Modular Redundancy Identical modules operating in an overall system design such that
failure of one module does not affect the output of the system
RF Radio frequency
V ac Volts ac
AC DISTRIBUTION CONNECTORS
(FACTORY INSTALLED TO EXCITER
AND RF POWER BLOCKS)
AC INPUT
170-270 V ac
1-PHASE
(L-L or L-N)
DC INPUT
128-168 V dc
Dimensions = mm (inches)
NOTE
This paragraph includes changes that
accommodate the user supplied dc power
source.
(e) Set the Requested Power Source to (m) In the Test Standby Side menu (see
AC (see 3.6.9, p. 3-27). 3.6.12.4, p. 3-34), select Run All
Tests. Each test should take about
(f) Clear the Events Log (see 3.6.5, p. 20 s. OK should be displayed.
3-23).
(n) Set the transmitter’s operating side to
(g) Select local control by pressing the A (see 3.6.4).
Control – Local button.
(o) For single transmitters, skip to step
(h) Ensure the transmitter’s main side is (p). For dual side transmitters, in the
set to B and the monitor mode is set Test Standby Side menu, select Run
to BYPASS (see 3.6.4, p. 3-22). All Tests. Each test should take
about 20 s. OK should be displayed.
(i) Apply an MSK signal (at the carrier
frequency) between 0.5 and 4 V peak (p) Set the power level to 0 W
to peak to the EXT RF IN - MSK A (simultaneously press the Power -
(and B if appropriate) BNC connector Increase and Decrease buttons).
on the back of the exciter/ control
assembly. (q) Set the analog meter to display
reflected power on the 0 to 400 W
(j) Reset the alarm status (see 3.6.3, p. scale (see 3.6.8.2, p. 3-26).
3-22). The pre-existing alarms should
clear. (r) In the Meters menu, use the f or g
buttons to display the average PA volts
(k) There should be no alarms indicated for side A.
on the System Diagram or GUI.
*
ATU VDC (OPTIONAL)
ATU-LP
* OR
RS-485 ISOLATED ATU-HP
INT SERIAL LINK
RF CABLE ANTENNA
FERRITE FEEDER
*
RF FEED FROM TRANSMITTER RF FEED TO ANTENNA
(NAUTEL P/N 151-1283-01) ANTENNA SYSTEM SYSTEM
J1 GROUND
PWR CABLE
FERRITE
*
STATION
REFERENCE
GROUND
* DENOTES CABLE LENGTH TO BE
20 FEET (6 METRES)
AC
POWER AC INPUT
SOURCE (OPTIONAL)
Dimensions = mm (inches)
*
ATU VDC (OPTIONAL)
* ATU-HP
RS-485 ISOLATED
INT SERIAL LINK
RF CABLE ANTENNA
FERRITE FEEDER
*
RF FEED FROM TRANSMITTER RF FEED TO ANTENNA
ANTENNA SYSTEM SYSTEM
GROUND
SPU2
NDB/DGPS
PWR CABLE INTERFACE/
FERRITE PROTECTION
* UNIT
STATION
REFERENCE
GROUND
* DENOTES CABLE LENGTH TO BE
20 FEET (6 METRES)
AC
POWER AC INPUT
SOURCE (OPTIONAL)
Dimensions = mm (inches)
System Diagram
Exciter Output
IPA/ Network
PA
Changeover
Low Voltage
Power Supply
External
Alarm
Low Voltage Power When turned on (red), indicates the active LVPS module (A2A7 or
Supply A2A11) has failed.
Power Supply When turned on (red), indicates a fault has occurred in one or more
of the switching power supplies that supply the RF power modules
This alarm will initiate a changeover in dual transmitters; the side of
the transmitter designated as standby will be operating as the active
side.
External Alarm When turned on (red), indicates the a low MSK input alarm OR
external interlock circuit is not presenting a closed circuit (inhibiting
RF power) OR the ATU (optional) or site interface PWB (optional)
are not responding OR the battery (optional) is below the user
established threshold.
IPA/PA When turned on (red), indicates a fault has occurred in one of the
RF power modules. This alarm will initiate a changeover in dual
transmitters. After a changeover, the side of the transmitter
designated as standby will be operating as the active side.
Output Network When turned on (red), indicates the transmitter’s RF power is being
cut back or shut back due to an impedance mismatch (high VSWR)
at the transmitter’s output.
NOTE
In each case, root-cause details of the fault are displayed in the
diagnostic display’s Events Logs (see paragraph 3.6.5)
Power Decrease Pushbutton switch that decreases the RF output power level of the
transmitter. RF power is decreased from maximum power to minimum
power in approximately 200 steps. Each step will decrease the output
voltage of the switch mode power supplies to the RF power modules
linearly – the RF output power decrease will follow a square law.
Pressing and holding the switch increases the rate of change.
When Local control is selected, all of the remote control circuits (except
the external interlock and RF off function) are disabled.
RF On Push button switch that turns on the transmitter's RF power stage and
cooling fans when it is pressed. Its integral lamp will be on when the RF
power stage is turned on. Transmitter will operate at the level stored in
the selected power pre-set.
RF Off Push button switch that turns off the transmitter's RF power stage when
it is pressed. Its integral lamp will be on when the RF power stage is
turned off.
E2
E11
E3
E10
E4
E5
E6
E7
E8
E9
E1, E2, Key CW Shorting jumpers that are installed in positions determined by
E3, E8, Jumpers the type of transmitter. In DGPS transmitters, the jumpers are
E9 factory installed in position 2. No user adjustment is required.
E4, E5, DGPS/BEACON Bi-position selection jumpers that are installed in positions
E6, E7, Jumpers determined by the type of transmitter. In DGPS transmitters,
E10, E11 the jumpers are factory installed to short pins 1 and 2. No
user adjustment is required.
INTERLOCK
CHARGER
MONITOR
RF OFF
INHIBIT
ALARM
AUDIO
AUDIO
RF ON
INPUT
TO-TALK
PDM
PRESS-
GND
GND
GND
GND
+ - + - + - + - + SHLD - + SHLD -
RS-422 RS-232 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
TB1
J4 J5 J21 1
1 1
TP8
C118 E11
C119
C120
TP9
GND L11 C116
R118
C96
Q12 C101
U22
Q9 R119
C97 C99 AGC BYPASS R115 C117
1 E10 R80 R151
R111 R148
Q13 MONITOR NORM BYPASS C114
R112 LEVEL C103 C104
R120 R124 E11
R146
C90 1
R121 R128 C105 C110 C48
R125 R129
R113 R122 Q14
Q15
U20
J13 C93
U16
1
Q10
C100 R161
R126 C111
C4
R96
R13 C45
R4 L2
J18
R14 L4 L6
R5 C6 C36 L3
R6 C29
C7 R27 C46 C52
C1 C30 R81 J16 J17
U1
CR20
C2 C8 R63 R72 C59 R87 C80
C60 R92
R44 Q7
U21
C20 C69 C81
R82 C82
R9
U8
C70
TP2
R30
C61
C78 R91
U11
U15
C74 R133
R102
U14
R158 R109
U17
GND R18 1 1
U6
U7
1
C34 C40 C44
C50
E5
E6
E7
E8
R15 L1 TP11
CR15 CR16 CR17 L8 L9 C83 C94 C112
C10 SINGLE CR18 L7
U19
C26 C79
U12
R16
R162 E18
R50 R53 R70 R75 C67 C76 C84 C95 R130 R138 C113
1 DIFF R76 C63 C68 C77 R131
CR1 R51 R54 R71 R105 C85
NORM BATTERY C62 R123
1
M1950124 V1
PANEL
REF DES DESCRIPTION
MARKING
E4 Press-To- Factory default is shorting pins 1 and 2. No user adjustment
Talk/Phantom is required.
Feed
E13 – E15 NORM/NDB Bi-position selection jumpers that are installed in positions
E17 determined by the type of transmitter. In DGPS transmitters,
the jumpers are factory installed in the DGPS position
(shorting pins 2 and 3). No user adjustment is required.
R124 MONITOR Adjusted to set the level of the RF MONITOR output, which is
LEVEL a sample of the RF output. This output is located on BNC
connector J8 on the rear of the exciter/control assembly).
PANEL
REF DES DESCRIPTION
MARKING
A1E1 A/B No user adjustment should be required. Always installed in
A1E2 position B.
A6R31 GAIN TRIM Adjusted, when interphase PDM driver PWB is enabled (the
or associated exciter is the active exciter). Compensates for
A10R31 tolerance differences between exciter 'A' and exciter 'B' in
dual exciter transmitters. One or both must be adjusted to set
the PDM pulse train to produce identical RF output levels
when either exciter is selected (see 4.3.6.10).
A8E2 KEYED CW/ Bi-position selection jumpers that are installed in positions
or NORMAL determined by the type of transmitter. In Vector transmitters,
A12E2 the jumpers are factory installed in the NORMAL position
(shorting pins 2 and 3). No user adjustment is required.
PANEL
REF DES DESCRIPTION
MARKING
A1A1DS3 MODULE FAULT When turned on (red), indicates that a fault has occurred in
or RF power module A or B and it is not contributing to the
A2A1DS3 transmitter’s RF output.
A1A2DS2 +18V When turned on (green), indicates the +24 V power supply
or voltage is being applied to RF power module A or B and that
A2A2DS2 the +18 V regulator is functioning.
A1A3F1 +15V Fuses the +15 V applied from the power module control/
or interface PWB to the power amplifier at 1 A.
A2A3F1
A5E1 RF Filter Frequency dependent jumpers that are factory installed for
through Jumpers the customer operating frequency. If a frequency change is
A5E36 required, change the position of these jumpers (see Figure
MD-22).
NOTE: Prefix all items with A3 through A6, as applicable, to obtain complete reference
designation.
PANEL
REF DES DESCRIPTION
MARKING
F1/F2 Exciter A Fuse line 1 (F1) and line 2 (F2) of the ac voltage applied to
exciter A at 10 A.
F3/F4 Exciter B Fuse line 1 (F3) and line2 (F4) of the ac voltage applied to
exciter B at 10 A.
F5/F6 Side A – Fuse line 1 (F5) and line 2 (F6) of the ac voltage applied to
Power Block 1 RF power block 1, side A at 10 A.
F7/F8 Side B – Fuse line 1 (F7) and line 2 (F8) of the ac voltage applied to
Power Block 1 RF power block 1, side B at 10 A.
F9/F10 Side A – Fuse line 1 (F9) and line 2 (F10) of the ac voltage applied to
Power Block 2 RF power block 2, side A at 10 A.
F11/F12 Side B – Fuse line 1 (F11) and line 2 (F12) of the ac voltage applied to
Power Block 2 RF power block 2, side B at 10 A.
F13/F14 Side A – Fuse line 1 (F13) and line 2 (F14) of the ac voltage applied to
Power Block 3 RF power block 3, side A at 10 A.
F15/F16 Side B – Fuse line 1 (F15) and line 2 (F16) of the ac voltage applied to
Power Block 3 RF power block 3, side B at 10 A.
F17/F18 Side A – Fuse line 1 (F17) and line 2 (F18) of the ac voltage applied to
Power Block 4 RF power block 4, side A at 10 A.
F19/F20 Side B – Fuse line 1 (F19) and line 2 (F20) of the ac voltage applied to
Power Block 4 RF power block 4, side B at 10 A.
PANEL
REF DES DESCRIPTION
MARKING
F1 Dc Supply - Fuses the battery voltage supply (from rectifier U1) applied to
Exciter the exciter stage at 12 A.
F2 Dc Supply – Fuses the battery boost voltage supply (from battery boost
RF Power PWB A2) applied to RF power block 1 at 12 A.
F4 Dc Supply – Fuses the positive (+) end of the battery input voltage
Battery Input (typically 48 V) applied to the LINE input (terminal 1) of line
filter U2 at 20 A.
SOFTWARE
12:43:16 Power: 0W Side A Bypass VERSION
Main Menu Vector DGPS HP
Changeover Control
SUB-MENU Events Log rev 1. 0. 2. 2
SELECTIONS Settings May 03 2007
Peripherals 09:48:39
RCMS Settings Nautel
Select Meters
Meters
Status 3.6.3
Power 3.6.15
Changeover Control 3.6.4
Events Log 3.6.5
Settings
Set Real Time Clock 3.6.6
Monitor Settings 3.6.7
Monitor Timeout 3.6.7 (b)
Power Thresholds 3.6.7 (d)
Automatic Reset 3.6.7 (f)
Meter Settings 3.6.8
Change Meter Groups 3.6.8.1
Select Analog Meter 3.6.8.2
Calibrate Analog Meter 3.6.8.3
Power Source Select 3.6.9
Configure Sonalert 3.6.10
Timed Shutdown 3.6.11
Factory Settings 3.6.12
Calibrate Digital Meters 3.6.12.1
Set Thresholds 3.6.12.2
Maximum Output Gain 3.6.12.3
Use Factory Settings 3.6.12.4
Peripherals 3.6.13
MSK Conditioner 3.6.13.1
Power Modules 3.6.13.2
ATU Controls 3.6.13.3
Test Standby Side 3.6.13.4
Select Peripherals 3.6.13.5
Module Check 3.6.13.6
RCMS Settings 3.6.14
Control Points 3.6.14.1
Monitor Points 3.6.14.2
Baud Rate 3.6.14.3
12:43:16 Power: 0W Side A Bypass ** Modulation parameters are displayed but not
Settings
Set Real Time Clock applicable for DGPS transmitters.
Monitor Settings
Meter Settings Set up the displayed parameters as follows:
Power Source Select
Configure Sonalert
Main Menu Select Back
12:43:16 Power: 0W Side A Bypass
Meter Settings
Change Meter Groups
Select Analog Meter
Calib. Analog Meter
(a) From the main menu, highlight Settings
(using f and g) and press Select.
Highlight Meter Settings and press Main Menu Select Back
Select. Use f and g to highlight
Change Meter Groups, Select Analog
Meter or Calib. Analog Meter and press
12:43:16 Power: 0W Side A Bypass
Select. Refer to paragraph 3.6.8.1 Forward Power: 0W
through 3.6.8.3 for further details. 0 600 1200
Reflec. Power: 0.0W
0 100 200
3.6.8.1 Changing Meter Groups VSWR: 1.00
For monitoring and troubleshooting 0 1 2
convenience, the currently displayed meters Save Backup Modify Back
on the diagnostic display’s meters screen can
be changed to display any three of the (a) Use f and g to select the parameter to
available meters: be replaced and press Modify. Use f
and g to select the desired parameter to
be monitored in its place. Press Done to
activate the change. Press Back.
• Low AC Volts: Yes or No (indicates if the • To configure an alarm for the Sonalert,
ac voltage dropped below the low ac use f and g to select the desired alarm;
threshold). press Toggle to change the status to ON.
• For Timed Shutdown, press Toggle to (a) From the main menu, highlight Settings
change between ENABLED and (using f and g) and press Select.
DISABLED. When Timed Shutdown is Highlight Factory Settings and press the
ENABLED, the transmitter will shut down f and Main Menu soft-keys
the Interval period (in hours:minutes) simultaneously.
after RF On is asserted.
Yes No
• For Auto Assert, press Modify to enable
editing of the asserting monitor point. Use
Press Yes to display the following options:
f and g to change the monitor point
between 1 and 40 (or Disabled). Press
Done to store the change. Monitor points 12:43:16 Power: 0W Side A Bypass
Factory Settings
can only enable the timed shutdown Calibrate Meters
timer. Set Timed Shutdown to Set Thresholds
DISABLED when using Auto Assert. Maximum Output Gain
Use Factory Settings
(d) When complete, return to previous menu • MSK Conditioner (para. 3.6.13.1)
by pressing Back. A prompt appears to • Power Modules (para. 3.6.13.2)
confirm saving modifications to the • ATU Controls (para. 3.6.13.3)
EEPROM. Press Yes or No. • Test Standby Side (para. 3.6.13.4)
• Select Peripherals (para. 3.6.13.5)
• Module Check (para. 3.6.13.6)
SIDE A SIDE B
Main Menu View Details Back
(a) Select the desired parameter, using f or (a) Press f or g until the desired parameter
g. To edit, press Modify and then use f is highlighted.
or g to adjust the Side B Scale factor or
MSK Reference. • If the Number of Power block expected
value is highlighted, the Modify option is
NOTE displayed. Press Modify and use f or g
The Side B Scale factor is factory set and to select between 1 and 4. Press Done
should not require user adjustment. If the when complete.
MSK alarm for one side (A or B) occurs at a
different level than the other side, adjust the • If one of the eight power module fields
Side B Scale factor up or down until the MSK (Block # 1 through 4, Side A and B) is
alarm for both sides occurs at the same level highlighted, the View Details option is
(minimum of 400 mV p-p). displayed. Press View Details to view
the following RF power module details:
After adjusting the Side B Scaling factor,
adjust a Pot value (press f and g) to
PA = Side A
enable the new scaling factor.
Bloc 1 = Block 1
(c) Press f or g to scroll through the (a) Use f and g to highlight the desired
options and press Select to enter the monitor point (1 through 40) Press
appropriate sub-menu (see 3.6.14.1 Toggle to change the logic level (0 or
through 3.6.14.3). 1) of the Default value. The logic level
determines the active (for status
• Control Points (see 3.6.14.1) outputs) or normal (for alarm outputs)
• Monitor Points (see 3.6.14.2) state for the monitor point’s remote
• Change Baud Rate (see 3.6.14.3) output.
3.6.14.1 Setting Control Points NOTE
Set the site interface PWB’s control points: Monitor points 1 through 40 correspond to
outputs connected to MONITOR POINT 1
12:43:16 Power: 0W Side A Bypass through 40 on TB1 and TB2 of the site
Control Points Set Value
Control Point 1 0
interface PWB.
Control Point 2 0
Control Point 3 0 (b) The values in the Current column
Control Point 4 0
Control Point 5 0 represent the existing state of the
Toggle Back monitor point. Press Set Current to
set the Current values to match the
Default values.
• Highlight the value for Maximum (a) Measure and record the following dc
Carrier Reference. Press Modify. voltages on the control/display PWB
(A2A1):
• Increase the value by 5. Press Done.
• TP18 (approx. 24 V)
(k) Return to step (h). • TP12 (approx. 15 V)
• TP20 (approx. -15 V)
(l) Set the maximum carrier reference: • TP9 (approx. 5 V)
• Record the current duty cycle and (b) In the Calibrate Meters menu (see
forward power values. 3.6.12 and 3.6.12.1) scroll through the
parameters until +24 Volt P/S is
• Record the power according to the highlighted. Press Modify.
external current probe.
(c) Adjust the value to match the TP18
• Highlight the value for Maximum voltage measured in step (a). Press
Carrier Reference. Press Modify. Done.
• Adjust the value to 1 higher than the (d) Repeat step (c) to calibrate the other
current Carr. Ref value. Press Done. parameters:
(m) The initial Forward Power • +15 Volt P/S (measured on TP12)
measurement should be within 20 % of • -15 Volt P/S (measured on TP20)
the actual value. In the Calibrate • +5 Volt P/S (measured on TP9)
Meters menu (see 3.6.12 and 3.6.12.1) • AC Voltage
calibrate the Forward Power. • Temperature (use a thermometer to
measure the ambient room
• Scroll through the parameters until temperature
Forward Power is highlighted. Press
Modify. NOTE
When you exit the Calibrate Meters menu a
• Adjust the reading to the same value message is displayed indicating that you
calculated in step (h). Record this have made changes. You will be prompted
level. Press Done. to save the changes to EEPROM so that
they can be restored in the event of a
(n) Increase the power until maximum power failure. Press Yes each time this
power is reached. Record the power prompt is displayed during the setup
level on the top line (status bar) of the procedure.
GUI display.
During initial turn-on and adjustment of
(o) Press Power Increase and Power transmitter power, the diagnostic display’s
Decrease at the same time to set the meters screen should be monitored.
RF power to 0 W. Press RF Off.
(c) In the Calibrate Meters menu (see (e) In the Calibrate Meters menu (see
3.6.12 and 3.6.12.1) scroll through the 3.6.12 and 3.6.12.1) scroll through the
parameters until PDM A (or PDM B, parameters until Reflec. Power is
depending on the transmitter’s active highlighted. The Reflec. Power value
side) is highlighted. Press Modify. should be within 20% of the value
determined in step (d).
(d) Adjust the value to match the positive
duty cycle measured on TP17 in step • Press Modify.
(a). Press Done.
• Adjust the value to match the level
4.3.6.6 Calibrating Reflected Power calculated in step (d). Press Done.
Threshold and Output Network Alarm
(f) Press Back and select Set
(a) Turn off the transmitter and disconnect Thresholds.
the dummy load from the transmitter’s
RF output. Short the transmitter’s RF (g) Press Next until Refl. Power
output to ground near the RF output. Shutback is displayed.
Install the external current probe on the
shorting jumper. (h) Monitor the external current while
slowly increasing the power to the
(b) In the Set Thresholds menu (see reflected power limit. Try to achieve a
3.6.12 and 3.6.12.2) set the Slowback current similar to the currents listed
Pwr (Per Block) value to 100 W. below, noting the number of modules
that are installed.
(c) Set RF output power to 0 W. Press RF
On. Monitor the external current while • One RF power module (80 W):
slowly increasing the power to half of increase until current is 2.5 A
the reflected power limit. Try to achieve
a current similar to the currents listed • Two RF power modules (160 W):
below, noting the number of modules increase until current is 3.6 A
that are installed.
• Three RF power modules (240 W):
• One RF power module (40 W): increase until current is 4.4 A
increase until current is 1.8 A
• Four RF power modules (320 W):
• Two RF power modules (80 W): increase until current is 5.1 A
increase until current is 2.5 A
(k) In the Set Thresholds menu, set the Low AC ref = 170 x TP13/Ac Voltage
Slowback Pwr (Per Block) to 30 W.
(c) Monitor the dc voltage at TP19 on the
(l) Press RF On. Verify the reflected control/display PWB.
power cutback to below 30 x N watts,
where N is the number of RF power (d) In the Set Thresholds menu (see
blocks (1-4) installed. Press RF Off. 3.6.12 and 3.6.12.2), scroll to the Low
AC Voltage threshold. Press Modify.
(m) Remove the shorting jumper from the
transmitter’s RF output. Reconnect the (e) Adjust the Low AC Voltage value until
dummy load to the transmitter’s RF the voltage at TP19 matches the low
output. ac voltage reference calculated in step
(b). Press Done.
4.3.6.7 Setting The RF Monitor Level
(f) Turn off the transmitter’s ac power. If
(a) Increase the transmitter’s RF output to testing is required, connect a variac
full power. between the ac power source and the
transmitter. Turn on the ac power.
(b) Connect a 50 Ω load to the RF
MONITOR BNC connector (J8 of (g) Use the variac to decrease the ac
remote interface PWB A2A3, voltage until the System Diagram’s AC
accessible at the back of exciter/ Mains LED. The Diagnostic Display
control assembly A2. Monitor the should display both Shutback A and
voltage with a digital multimeter. Low AC. Record the ac voltage.
(c) Set the MSK input level to 400 mV p-p. (b) Use an oscilloscope to monitor TP17 of
If no alarms are indicated, proceed to interphase PDM driver PWB A (A2A6).
step (d). In the MSK Conditioner menu
(see 3.6.13.1), increase the MSK (c) On interphase PDM driver PWB A
Threshold level to 255. Press Reset in (A2A6), adjust the GAIN TRIM
the Status menu. The System potentiometer (R31) four turns counter
Diagram and Diagnostic Display clockwise and one and a half turns
should not indicate an alarm. clockwise. On interphase PDM driver
PWB B (A2A10), adjust the GAIN
(d) In the MSK Conditioner menu (see TRIM potentiometer (R31) four turns
3.6.13.1), decrease the MSK counter clockwise.
Threshold level until an alarm appears
on the System Diagram and Diagnostic (d) Press RF On. Increase the
Display. Press Done. Increase the transmitter’s RF output to full rated or
MSK input level to 2 V p-p and press maximum power, whichever is lower.
Reset in the Status menu. The
System Diagram and Diagnostic (e) Use an external current probe to
Display should not indicate an alarm. measure RF output power:
2
(e) Lower MSK input A until the System Power = Current x Rload
Diagram displays an External Alarm.
(f) In the Maximum Output Gain menu
(f) The Diagnostic Display should indicate (see 3.6.12.3), calibrate the duty cycle
MSK Alarm A and Shutback A. Reset and forward power as follows:
the MSK input to 2 V p-p and reset the
alarms. • Highlight the value for Set Duty Cycle.
Press Modify.
(g) Repeat this procedure for side B. If
necessary, adjust the Side B Scale • Change the value to match the positive
factor (see 3.6.13.1) to get similar duty cycle measured at TP17 in step
results. (c). Press Next.
(h) Repeat step (e). (a) Measure and record the dc voltage
between TB1-1 and TB1-2 on the dc
(i) Set the maximum carrier reference: distribution assembly (A7).
• Record the current duty cycle and (b) In the Calibrate Meters menu (see
forward power values. 3.6.12 and 3.6.12.1) scroll through the
parameters until Battery Voltage is
• Record the power according to the highlighted. Press Modify.
external current probe.
(c) Adjust the value to match the voltage
• Highlight the value for Maximum measured in step (a). Press Done.
Carrier Reference. Press Modify.
NOTE
• Adjust the value to 1 higher than the When you exit the Calibrate Meters menu a
current Carr. Ref value. Press Done. message is displayed indicating that you
have made changes. You will be prompted
(j) Increase the power until maximum to save the changes to EEPROM so that
power is reached. Record the power they can be restored in the event of a
level on the top line (status bar) of the power failure. Press Yes each time this
GUI display. prompt is displayed during the setup
procedure.
(k) Press Power Increase and Power
Decrease at the same time to set the (d) In the Power Source Select menu,
RF power to 0 W. Press RF Off. change the transmitter’s Requested
Power Source to DC (see 3.6.9).
(l) Select side B in the Exciter Control
menu. (e) Press RF On and increase the RF
output to rated power.
(m) Press RF On. Ensure all side B RF
power module fans are on. (f) Use a clip-on dc current meter to
measure the current between the
(n) Press Power Increase until you reach battery and TB1-1 of the dc distribution
maximum power. Adjust GAIN TRIM assembly (A7).
potentiometer R31 on interphase PDM
driver PWB B (A2A10) to ensure that (g) In the Calibrate Meters menu scroll
the output power matches the output through the parameters until Battery
power recorded in step (k). Current is highlighted. Press Modify.
• Ensure electrical connections are not (a) Determine the origin of the fault by
broken while current is flowing in the noting which of the system diagram’s
circuit. lamps has turned on. If no system
diagram lamp is on, proceed to step (b)
• Ensure voltages are not present on for non-alarm troubleshooting tips.
external control/monitoring circuits
when they are connected. NOTE
In dual side (A and B) transmitters, some
5.5 TROUBLESHOOTING FRONT faults will also initiate a Changeover
PANEL ALARMS alarm. In this case, the transmitter will
Front panel fault analysis can be performed continue to operate using the standby side.
from the exciter panel. There are several This may allow troubleshooting (and
ways to use the front panel to determine subsequent repair) to be deferred to a
the occurrence and origin of a fault: more convenient time.
(c) The diagnostic display will indicate the Viewing the diagnostic display’s Events
current active faults and more Log (see paragraph 3.6.5) can also assist
specifically identify the nature of the in diagnosing a fault.
fault.
(f) Other fault indications may prompt the
e.g., PDM Drive A Fail troubleshooter to replace other PWBs
or assemblies in the exciter/control
(d) Attempt to clear the alarm by pressing assembly or an RF power block (e.g.,
the reset button. If the alarm persists, PA Alarm A 1 indicates a fault has
it will not be cleared from the display. occurred on the side A RF power
module in RF power block 1).
(e) In the example given in step (c), a
PDM Drive A Fail has occurred NOTE
indicating a problem with exciter A’s Replacement procedures (paragraphs 5.8
interphase PDM driver PWB. The and 5.9) are provided for RF power
suspect PWB should be replaced as modules and PWBs/assemblies that
detailed in paragraph 5.8.1.2. require specific removal/installation or
adjustment instructions. Instructions have
not been included for assemblies that are
straightforward to replace and require no
re-calibration.
Low Voltage Power Supply LVPS Fault A or B Replace associated LVPS buck converter PWB [side A (A2A7) or exciter B (A2A11)] and/or ac/dc universal N/A N/A
input power supply [side A (A2U2) or side B (A2U3)].
Power Supply Over Voltage PS Replace switch mode power supply PWB (A2 of associated RF power module). 5.6.1 3.6.13.4 (ensure the
A or B, 1 to 4 replaced/repaired module is
on the standby side)
Power Supply Over Current PS Check/replace associated fuses (F5 through F10, see assembly silkscreen) on the ac power distribution 5.6.1 3.6.13.4 (ensure the
A or B, 1 to 4 assembly (A8). If fuses are OK, replace switch mode power supply PWB (A2 of associated RF power replaced/repaired module is
module). on the standby side)
If the transmitter is running in dc mode (optional), and this alarm is indicated for all modules on the active
side, replace battery boost supply A7U1. Otherwise, check cabling between A7 and A3 through A6.
Power Supply High Temp PS Check fans. Ensure they are spinning at an adequate speed (a minimum of 3000 RPM, see 3.6.13.2). If N/A N/A
A or B, 1 to 4 necessary, replace the appropriate fan.
Power Supply PS A or B Missing Modules, 1 to 4 An RF power module has been removed from the associated side. N/A N/A
PA Modulator Fail Check/replace FET on modulator assembly (A5 of associated RF power module). 5.6.1 3.6.13.4 (ensure the
A or B, 1 to 4 5.7 replaced/repaired module is
on the standby side)
PA PA Alarm Check/replace FETs on power amplifier (A3 of associated RF power module). 5.6.1 3.6.13.4 (ensure the
A or B, 1 to 4 5.7 replaced/repaired module is
on the standby side)
PA PDM Inhibit A or B A module has been removed from the transmitter. A PS Missing Module message will indicate which module N/A N/A
has been removed.
Exciter Low NVRAM Bty Replace battery BT1 on the control/display PWB (A2A1). N/A N/A
Exciter PDM Latch A or B Check/replace associated fuses (F5 through F20, see assembly silkscreen) on the ac power distribution 5.8.1.1 4.3.6.3 (single side) or
assembly (A8). If fuses are OK, change the active side of the exciter and run a standby side test on the 4.3.6.10 (dual side)
power supply (see 3.6.13.4). If a fault is detected, replace switch mode power supply PWB of faulty power 3.6.13.4 (ensure the
module. If no fault is detected, replace interphase PDM driver PWB [side A (A2A6) or exciter B (A2A10)]. replaced/repaired module is
on the standby side)
Vector DGPS Transmitter Technical Instruction Manual Page 5-5 (5-6 Blank)
Section 5 Maintenance and Troubleshooting Issue 0.1
Table 5-1: Troubleshooting and Replacement Tips (Continued)
Front Panel Status See Troubleshooting/ See Re-calibration
Action
LED Message Replacement Paragraph Paragraph
Exciter Monitor Fault Indicates a fault in a monitor PWB. The Monitor Fault will be accompanied by an indication of the fault. If it is 5.8.2 4.3.6.9
A or B not accompanied by a specific fault, replace the exciter monitor/generator PWB [side A (A2A8) or side B 4.3.5.4
(A2A12)].
Exciter E/G not responding A or B Indicates that an exciter monitor/generator PWB is not responding. Replace the exciter monitor/generator 5.8.2 4.3.6.9
PWB [side A (A2A8) or side B (A2A12)]. 4.3.5.4
Exciter Mon PGM Fault A or B Indicates that an exciter monitor/generator PWB has an EEPROM or Flash memory error. Replace the 5.8.2 4.3.6.9
exciter monitor/generator PWB [side A (A2A8) or side B (A2A12)]. 4.3.5.4
Exciter Pwr. Monitor Fail A or B Indicates that the transmitter’s output power is outside of the desired thresholds. If there is no accompanying 5.7 3.6.13.4 (ensure the
error message, a power amplifier (A3) in an RF power block may be damaged. Try operating the transmitter replaced/repaired module is
at rated power. If the problem persists, check/replace FETs on the associated power amplifier. on the standby side)
Exciter Monitor Fail Indicates that one, not both, of the exciter monitor/generator PWBs [side A (A2A8) or exciter B (A2A12)] 5.8.2 4.3.6.9
requested a changeover. It is typical for a brief monitor fail event to occur after a changeover. 4.3.5.4
If the problem persists and the transmitter is not operating near an alarm threshold, replace the faulty exciter
monitor/generator PWB [side A (A2A8) or side B (A2A12)].
Output Network SWR Shutback RF power has been inhibited due to high reflected power. Check the RF path between the transmitter’s RF N/A N/A
output and the antenna system. An SWR alarm occurs if the sensed reflected power level exceeds an SWR
of 2:1 or 1.5:1.
If the instantaneous peak SWR exceeds 2:1, the RF output is shut back. The power level will automatically
recover to its previous level. If two consecutive SWR shutbacks occur within a two second period, the RF
output is cut back (see SWR Slowback).
Output Network Cutback Level There are 18 steps (or cutback levels) available. The transmitter will continue decreasing or increasing the N/A N/A
1-18 RF output power until normal operating power is achieved, at which point the SWR alarm will disappear.
If the average peak SWR exceeds 1.5:1, the RF output is cut back (reduced) until the reflected power level
falls below the 1.5:1 level.
During an SWR alarm, the System Diagram’s Output Network alarm lamp blinks and the Diagnostic Display
indicates a Shutback (if the reflected power is greater than 2:1 SWR) as well as the cutback level.
Changeover Monitor Changeover Check the accompanying error message to determine the cause of the changeover. N/A N/A
Changeover Monitor Shutdown Check the accompanying error message to determine the cause of the shutdown. N/A N/A
Vector DGPS Transmitter Technical Instruction Manual Page 5-7 (5-8 Blank)
Section 5 Maintenance and Troubleshooting Issue 0.1
Table 5-1: Troubleshooting and Replacement Tips (Continued)
Front Panel Status See Troubleshooting/ See Re-calibration
Action
LED Message Replacement Paragraph Paragraph
External Alarm Ext Interlock Open An external interlock circuit is open. Check the integrity of the circuitry connected between terminals TB1-19 N/A N/A
and TB1-20 of the remote interface PWB (A2A3).
External Alarm Charger Alarm Check for battery charger failure. N/A N/A
External Alarm Low Battery Voltage The battery voltage is below the low voltage threshold. N/A N/A
External Alarm ATU Not Responding The associated ATU is not responding. N/A N/A
External Alarm RCMI Not Responding The NDB site interface PWB is not responding. Replace the NDB site interface PWB. N/A 4.3.5.1
4.3.5.3
External Alarm MSK Alarm A/B The Indicated MSK input is below the established threshold N/A N/A
- - Replace the RF power probe (A1A1). N/A 4.3.6.3
- - Replace the optional dc control/monitor PWB (A7A1). N/A 4.3.6.11 (if applicable)
4.3.6.12 (if applicable)
- - Replace the modulator filter PWB (A1A4 or A2A4 of the applicable RF power block). N/A 3.6.13.4 (ensure the
replaced/repaired module is
on the standby side)
- - Replace the RF filter PWB (A5 of the applicable RF power block). N/A 4.3.6.2
NOTE: PWBs and assemblies that are not referenced in this table do not require special replacement or re-calibration procedures.
(a) Remove the front cover from the 5.7 FET CHECKING/
associated RF power block 1 (A3) REPLACEMENT
through 4 (A6) as applicable (see The transmitter contains many FETs and
Figure MD-1) by removing four M5 other switching semiconductor devices.
screws. The FETs most likely to fail are in the RF
power modules (A and B, as applicable) in
(b) Loosen the securing screw at the each RF power block (1 through 4, as
bottom, front of the appropriate RF applicable). For failures caused in an RF
power module (side A module on the power module, remove the module (see
left, side B module on the right). 5.6.1), check the devices listed below and,
Carefully pull the RF power module out if necessary, replace them.
of the transmitter cabinet.
• FETs Q1 and Q2 (Nautel Part # QR54)
(c) Replace a defective FET (see 5.7) or of switch mode power supply PWB A2
an entire PWB or assembly (see (see Figures MD-15 and MD-17)
Figure MD-15) as necessary.
• power MOSFETs Q1 through Q4
NOTE (Nautel Part # QAP49) of power
If an operational RF power module is amplifier A3 (see Figures MD-15 and
available, you can install it in the MD-18)
transmitter while you repair the defective
module. Refer to paragraph 5.6.2 to install • power MOSFET Q1 (Nautel Part #
an RF power module. QAP49) of modulator A5 (see Figure
MD-15; same device as in power
amplifier A3, see MD-18)
(e) Remove the exciter/control assembly’s (g) For dual transmitters, perform the
top and bottom covers. Equalizing Exciter Gain adjustment
procedure (see 4.3.6.10). For a single
(f) Replace the appropriate assembly or transmitter perform the Calibrating
PWB (see 5.8.1 or 5.8.2). Transmitter Output Power adjustment
procedure (see 4.3.6.3).
5.8.1 Exciter Interface PWB and
Interconnecting PWB Replacement 5.8.1.2 Exciter Interface PWB
The exciter interface PWB (A2A1) Removal/Replacement
physically interconnects with the interphase
PDM driver PWBs (A2A6 and A2A10). (a) Remove all connections to the top and
Removing the exciter interface PWB bottom of the exciter interface PWB.
involves removing its interconnecting PWBs
first. Complete the instructions in the sub- (b) Remove and retain 13 sets of mounting
paragraphs (see 5.8.1.1 and 5.8.1.2) to hardware for the exciter interface PWB.
replace the appropriate PWB. Complete all Remove the PWB.
three paragraphs if replacing the exciter
interface PWB. (c) Install the new exciter interface PWB.
Re-install connections to the top and
bottom sides. Use the connector tag
labels or the connector mating
information in Table 8-3 to determine
proper connections.
(a) Remove and retain four sets of (f) Perform the following calibrations:
mounting hardware for the exciter 4.3.6.9 and 4.3.5.4.
monitor/generator PWB being replaced.
Vector DGPS Transmitter Technical Instruction Manual Page 6-1 (6-2 Blank)
Section 6 Theory of Operation Issue 0.1
BATTERY BOOST B+ (OPTIONAL) RF OUTPUT FINAL RF OUTPUT TO ATU
RF POWER
BLOCK
(OPTIONAL)
DGPS SITE
INTERFACE RS-485 INT SERIAL LINK
(OPTIONAL)
INT SERIAL LINK, CONTROL/MONITOR
* INSTALLED IN EXCITER/
CONTROL/MONITOR VDC 24VDC(A), RF DRIVE(A), PDM(A)
BLOCK
EXTERNAL CONTROL/MONITOR 24VDC(B), RF DRIVE(B), PDM(B)
RF OUTPUT
EXTERNAL MSK INPUT
RF POWER
RS485 ISOLATED INTERNAL BLOCK
SERIAL LINK (ATU)
(OPTIONAL)
RF OUTPUT
RF POWER
BLOCK
(OPTIONAL)
AC POWER
AC POWER AC
DISTRIBUTION
FWD/REFLD POWER, RF VOLT MONITOR, RF CURRENT MONITOR
B1950505 VA
24VDC, AC RELAY CONTROL
Dimensions = mm (inches)
6.5.2 Interphase PDM Driver PWBs When the Carrier Ref input (U6-Y1) is 4.7 V
See Figure SD-19. The interphase PDM and the B+ Sample input (U7-X1) is 5.9 V (B+
driver PWBs (A2A6 and A2A10) produce a voltage of 350 V), the gain of U6 is 0.80 for
pulse train of variable width as their PDM the dc reference applied to U6-X1. The
output. The PDM repetition rate (ƒPDM) is a U7-Y1 current is 0.80 times the U6-X1
fixed frequency normally between 130 kHz current. U3B is connected as a less than
and 133 kHz. The frequency is determined by unity amplifier and its gain is summed with
the 2ƒPDM input, which is produced by the U7's gain. The end result is the total voltage
active exciter monitor/generator PWB. The gain of the circuit, relative to the voltage at
PDM drive signal, which determines the the output of U2D (1.4 V), is a nominal 0.75
transmitter output power level, is applied to when GAIN TRIM potentiometer R31 is set to
the modulator assemblies in RF power the centre of its range. The output of U3B
modules A or B (see Figure SD-24) contained (TP8) is 1.049 V (1.4 V x 0.75).
in the RF power block.
The gain of U7 will change in direct proportion
6.5.2.1 Carrier Level Control to changes in the Carrier Ref voltage. If the
The carrier level control circuit consists of U6, Carrier Ref voltage is set to 0 V, or it is
U7 U2A, U2D, U3B, U3D, U13A and their clamped to ground because Q1 is turned on,
associated components. U6 and U7 are U7's gain is minimum (zero). In turn, the dc
analog multipliers connected as a variable reference's multiplication factor is minimum
gain, wide-band, linear amplifier. The (zero). The transmitter's RF output is turned
modulation reference (U6-X1) is multiplied by off.
a factor determined by the level of the carrier
ref (U6-Y1) and B+ sample (U7-X1) signals to
Vector DGPS Transmitter Technical Instruction Manual Page 6-7 (6-8 Blank)
Section 6 Theory of Operation Issue 0.1
+15VDC (A) INT SERIAL LINK, CONTROL/MONITOR
FREQUENCY
SYNTHESIZER CONTROL/MONITOR 24VDC(A), RF DRIVE(A), PDM(A) TO RF POWER BLOCK
PWB
A RF DRIVE (A), 2FPDM (A) 24VDC(B), RF DRIVE(B), PDM(B)
+15VDC (B)
FREQUENCY
SYNTHESIZER CONTROL/MONITOR
PWB
B RF DRIVE (B), 2FPDM (B)
+24VDC
SPEAKER +24VDC (A)
ANALOG/ +/-VDC
AC/DC LVPS
DIGITAL POWER A
DISPLAY AC SAMPLE MONITOR
SUPPLY
A
+24VDC
+24VDC (B)
ATU
POWER
SUPPLY +24VDC TO ANTENNA TUNING UNIT
B1950017 VD
FILTER
Dimensions = mm (inches)
Ramp
PDM 1
During normal operation, C58 will charge If a PDM fault is sensed, the PDM fault
through R67 towards 15 V when the detector circuit applies a current-sink-to-
PDM1 output is 15 V ('on time') and CR3 ground (logic low) to U9-5 and causes the
is reversed biased. It will instantly flip-flop to switch to and latch in its 'set'
discharge to 0 V, through CR3, when the state. Relay K1 de-energizes and
PDM1 output switches to 0 V ('off time'). disconnects the PDM output from the
The repetition rate of the PDM1 on/off transmitter circuits. The PDM latch output
periods ensures the charge on C58 will not (J1-11) is activated (5 V). This condition is
exceed 5 V, provided each PDM1 cycle maintained until the flip-flop is reset by the
contains an 'off time'. If a PDM failure removal of the logic low from U9-5 (no
occurs such that it produces a continuous PDM fault) and the application of logic low
'on time', C58 will charge more positively to U9-1 (a logic true current-sink-to-ground
than 5 V. U12A's output will switch to a reset PDM command is applied to J1-1).
current-sink-to-ground and toggle the
shutback latch circuit to its 'set' state. 6.5.2.8 PDM Inhibit
The PDM inhibit circuit consists of U9D,
6.5.2.7 Shutback Latch transistor Q2, and their associated circuits.
The shutback latch circuit inhibits the 'on Its function is to instantly clamp the output
time' of the PDM output and, in turn, the of the PDM generator to ground (zero
RF output of the transmitter whenever a carrier level) when a logic true (current-
transmitter originated Inhibit PDM (P1-16) sink-to-ground) inhibit PDM input is
command is applied. This circuit provides applied to P1-16, or when the PDM fault
additional protection to the transmitter's detector circuit senses a PDM fault and
RF power stages when faults are detected the shutback latch circuit’s flip-flop is
or actions are initiated that may cause RF latched in its ‘set’ state. When neither of
stress current thresholds to be exceeded. these conditions are true, the PDM inhibit
Its function is to de-energize K1 and circuit has no influence.
The HO output, which contains the PDM data, 6.6.2 Power Block Distribution PWB
is applied to the gate of power MOSFET Q1 See Figure SD-27. The power block
as its on/off control. distribution PWB (A4 of each RF power
block) provides the following functions:
6.6.1.3.3 B+ Switching MOSFET
Power MOSFET Q1 is connected to switch • Interfaces critical signals and serial bus
the B+ voltage at the on/off ratio of the PDM information between the RF power block
data on U1's HO output, which is applied to its and the exciter/control/ monitor stage.
gate. The resultant PDM (B+) output contains
• If RF power module A (or B) is removed,
the PDM data applied to J2-7 at a high (0-B+)
provides an Inhibit PDM signal (using
logic level. Free-wheeling diode CR6
FETs Q1 and Q2) to all remaining side A
prevents negative overshoot by providing
(or side B) RF power modules.
current flow when MOSFET Q1 is off.
• Controls the status of the RF power
6.6.1.4 Modulator Filter PWB block’s selector relay K1, which
See Figure SD-24. The modulator filter PWB determines which RF power module (side
(A4) consists of inductors L1 and L2 and A or B) is contributing to the RF output.
B+ SAMPLE (A)
24VDC(B), RF DRIVE(B), PDM(B) RF POWER
SERIAL LINK, CONTROL/MONITOR MODULE
A RF POWER MODULE
24VDC(A), RF DRIVE(A), PDM(A) OUTPUT A
A
RF POWER MODULE
OUTPUT B
RF POWER
B+ SAMPLE (B) MODULE
B
SERIAL LINK, CONTROL/MONITOR
RELAY CONTROL
B1950016 VD
Dimensions = mm (inches)
MODULATOR
FROM RF POWER BLOCK AC POWER B+ VDC FILTER
SWITCH RF POWER MODULE TO IMPEDANCE
MODE OUTPUT MATCHING TRANSFORMER
POWER
INT SERIAL LINK, CONTROL/MONITOR SUPPLY
MODULATOR
CONTROL/MONITOR
FROM RF POWER BLOCK +VDC
DISTRIBUTION PWB RF POWER
AMPLIFIER
24VDC, RF DRIVE, PDM CONTROL/MONITOR
+VDC
POWER Fpdm/PDM
MODULE
INTERFACE
+VDC
RF DRIVE
MONITOR
24VDC FANS
B1950015 VE
TACH
Dimensions = mm (inches)
PUSH-PULL CLASS 'D' OPERATION Power MOSFETs can be used to replace the
switches as depicted in the simple class 'D'
If S1 and S2 are opened and closed with a operation and push-pull class 'D' operation
50% duty cycle, a square wave of current, at examples. Note that the switch contacts are
the switching frequency, is passed through replaced by the phase-oriented secondaries
the primary of the transformer and of an RF drive transformer. Q1 corresponds
transformed to its secondary. If the filter is to S1-A, Q2 to S1-B, Q3 to S2-B and Q4 to
designed to pass the switching frequency, but S2-A, as depicted in the push-pull class 'D'
attenuate its harmonics, a sine wave is operation example. Q1 and Q4 turn on/off
applied to the load. together and Q2 and Q3 turn on/off together.
A1 A3 A2
RF COMBINER/PROBE RF POWER BLOCK EXCITER/CONTROL ASSY
NAX234A NAE89
NAH54 (VRD750), NAH54/01 (VRD1500)
NAH54/02 (VRD2250), NAH54/03 (VRD3000)
(SEE NAX234A FAMILY TREE)
A2A3 A2A4
REMOTE INTERFACE PWB NDB SITE INTERFACE PWB
NAPI78A NAPI79
A7 A8
DC POWER DISTRIBUTION AC POWER DISTRIBUTION (OPTIONAL)
NAX235/01 (VRD750), NAX235/02 (VRD1500) NAX233/01 (VRD750),NAX233/02 (VRD1500)
NAX235/03 (VRD2250), NAX235/04 (VRD3000) NAX233/03 (VRD2250),NAX233/04 (VRD3000)
A2A5 A2A6
INTERPHASE PDM DRIVER PWB (A)
NOT USED NAPM11
A7A1
DC CONTROL/MONITOR PWB
NAPC149B
A2A7 A2A8
LVPS BUCK CONVERTER PWB (A) EXCITER MONITOR/GENERATOR PWB (A)
NAPS32/01 NAPE76A/02
A7A2
BATTERY BOOST PWB
NAPS34
A2A9 A2A10
INTERPHASE PDM DRIVER PWB (B)
NOT USED NAPM11
A7A3
BATTERY BOOST PWB
NAPS34
A2A11 A2A12
(NOT USED ON NAX235/01) LVPS BUCK CONVERTER PWB (B) EXCITER MONITOR/GENERATOR PWB (B)
NAPS32/01 NAPE76A/02
A2A13
DC/DC POWER SUPPLY PWB
NAPS33
F1950504 VA
A1 A2 A4
RF POWER MODULE (A) RF POWER MODULE (B) POWER BLOCK DISTRIBUTION PWB
NAP33A NAP33A NAPI81
(SAME AS A1)
A1A1 A1A2 A5 A6
CONTROL/INTERFACE PWB SWITCH MODE POWER SUPPLY PWB RF FILTER PWB RF TRANSFORMER PWB
NAPC148 NAPS31A/01 NAPF05 NAPX32/01
A1A3 A1A4
POWER AMPLIFIER MODULATOR FILTER PWB
NAAA06 NAPF06
A1A5
MODULATOR ASSY
NASM11A/01
F1950502 VB
Page 1 of 82 195-1015
195-3001-01 Cableform Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
P01 MTA, Standard Dust Cover, 8 pin JU07 640551-8 09482
P01 MTA, Keyed Closed End Housing,8 pin,22AWG JU28 644463-8 00779
P02 MTA, Standard Dust Cover, 4 pin JU02 640551-4 09482
P02 MTA, Keyed Closed End Housing,4 pin,22AWG JU27 644463-4 00779
P03 MTA, Standard Dust Cover, 4 pin JU02 640551-4 09482
P03 MTA, Keyed Closed End Housing,4 pin,22AWG JU27 644463-4 00779
P10 MTA, Standard Dust Cover, 4 pin JU02 640551-4 09482
P10 MTA, Keyed Closed End Housing,4 pin,22AWG JU27 644463-4 00779
W08 Cable,SATA,.5m,Straight to Straight UA90 88758-0210 13150
W09 Cable,SATA,.5m,Straight to Straight UA90 88758-0210 13150
W11P1 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W11P1 Conn, IDC, D-Sub, P, HDE-20, 25-Pos JT31 745496-3 09482
W11P2 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W11P2 Conn, IDC, D-Sub, P, HDE-20, 25-Pos JT31 745496-3 09482
W12P1 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W12P1 Conn, IDC, D-Sub, S, HDE-20, 25-Pos JT30 745495-3 09482
W12P2 Conn, Plug, Size 11-4 JQ02 206429-1 09482
W12P2 Conn, Clamp, Strain Relief, Size 11, Std JQ03 206062-1 09482
W12P3 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W12P3 Conn, IDC, D-Sub, P, HDE-20, 25-Pos JT31 745496-3 09482
W13 Line Cord, 10A/250Vac, M & F,8Ft, 18 AWG JM48 ECM-13032-BLACK- ELECTRO
8FT ELCTRO CORD
MAN.
W13P1 Plug, Rewireable,250Vac, 16A JDP46 4796.0000(RoHS) SCHURTE
W15P01 Conn, Plug, Size 11-4 JQ02 206429-1 09482
W15P01 Conn, Clamp, Strain Relief, Size 11, Std JQ03 206062-1 09482
W15P02 Conn, Plug, Size 11-4 JQ02 206429-1 09482
W15P02 Conn, Clamp, Strain Relief, Size 11, Std JQ03 206062-1 09482
Page 2 of 82 195-3001-01
195-3014 Ribbon Cable Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
W01P1 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W01P2 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W02P1 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W02P2 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W03P1 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W03P2 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W04P1 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W04P2 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W05P1 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W05P2 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W06P1 Conn, Recept, Ribbon Cable, 20 pin JP45 746288-4 00779
W06P2 Conn, Recept, Ribbon Cable, 20 pin JP45 746288-4 00779
W06P3 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W07P1 Conn, Recept, Ribbon Cable, 20 pin JP45 746288-4 00779
W07P2 Conn, Recept, Ribbon Cable, 20 pin JP45 746288-4 00779
W10P1 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
W10P2 Conn, Recept, Ribbon Cable, 40 pin JP51 746288-9 00779
Page 3 of 82 195-3019
195-5001-01 Power Block Cableform Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
P01 Conn, Plug, Size 11-4 JQ02 206429-1 09482
P01 Conn, Clamp, Strain Relief, Size 11, Std JQ03 206062-1 09482
P07 Line Cord, 220V, 18/3AWG, 5VT JM46 18/3 AWG, 5VT 0B445
P08 Line Cord, 220V, 18/3AWG, 5VT JM46 18/3 AWG, 5VT 0B445
W1P01 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W1P01 Conn, IDC, D-Sub, S, HDE-20, 25-Pos JT30 745495-3 09482
W1P02 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W1P02 Conn, IDC, D-Sub, P, HDE-20, 25-Pos JT31 745496-3 09482
W1P03 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W1P03 Conn, IDC, D-Sub, S, HDE-20, 25-Pos JT30 745495-3 09482
W1P04 Conn, Shell, D-Sub, 25 pin, T-Screw JK16 DBBS-25 71468
W1P04 Conn, IDC, D-Sub, P, HDE-20, 25-Pos JT31 745496-3 09482
W2P01 Conn, Coax, N, Plug, 50ohm, Crimp, RG58 JDP22 82-5375 02660
W2P02 Conn, Coax, N, Plug, 50ohm, Crimp, RG58 JDP22 82-5375 02660
XA1P1 Conn,Sckt Housing,12 Socket,Metrimate JP66 211758-1 09482
XA2P1 Conn,Sckt Housing,12 Socket,Metrimate JP66 211758-1 09482
Page 4 of 82 195-5001-01
NAAA06 Power Amplifier Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Ceramic, 1.0uF 100V CAP16 RPE114Z5U105M100 91929
V
C02 Capacitor,Polyprop,0.056uF,10%,600V CP30 716P56396L SBE
C03 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C04 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C05 Capacitor, Ceramic, 1.0uF 100V CAP16 RPE114Z5U105M100 91929
V
C06 Capacitor, Ceramic, 1.0uF 100V CAP16 RPE114Z5U105M100 91929
V
C07 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
CR01 Diode, Power Rectifier, 4A, Ultra Fast QM22 MUR460 04713
CR02 Diode, Power Rectifier, 4A, Ultra Fast QM22 MUR460 04713
CR03 Diode, Power Rectifier, 4A, Ultra Fast QM22 MUR460 04713
CR04 Diode, Power Rectifier, 4A, Ultra Fast QM22 MUR460 04713
CR05 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
E01 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E02 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E03 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
F01 Fuse, 1A, 250V, Slow, 3AG FA08 313001 75915
J01 Conn, Header, Ribbon Cbl, 10 pin JA49 499910-1 00779
Q01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
Q02 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
Q03 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
Q04 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
Q05 Transistor, NPN, Switch/Amplifier QA45 2N4401 04713
R01 Resistor, Film, 100 Ohms, 5%2W RBP07 GS-3, 100 OHMS 75042
R02 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
R03 Resistor, MF, 15.0K Ohms, 1PC1/4W RAB39 MF1/4DL1502F 59124
R04 Resistor, MF, 8.25K Ohms, 1PC1/4W RAB36 MF1/4DL8251F 59124
R05 Resistor, Film, 33K Ohms, 5%,2W RBP22 GS-3, 33K OHMS 75042
R06 Resistor, MF, 1K Ohms, 1PC 1/4W RAB25 MF1/4DL1001F 59124
R07 Resistor, MF, 1K Ohms, 1PC 1/4W RAB25 MF1/4DL1001F 59124
T01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
U01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
XF01 Fuseholder, PWB Mount, Type 3AG FA31 4245 91833
Page 5 of 82 NAAA06
NAE89 Exciter Control Assy, Vector
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
A01 Control Display PWB Assy NAPC147B 195-2050-02 37338
A02 Exciter Interface PWB Assy NAPI76 195-3020 37338
A03 Remote Interface, Basic NAPI78A 195-2060-01 37338
A04 See Sales Order % % SEE SALES 37338
ORDER
A05 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A06 Interphase PDM Driver PWB Assy NAPM11 197-3060 37338
A07 LVPS Buck Converter PWB Assy NAPS32/01 195-7025-01 37338
A08 Exciter Monitor/GeneratorPWB Assy, (>250W) NAPE76A/02 195-3030-05 37338
A09 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A10 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A11 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A12 Exciter Monitor/GeneratorPWB Assy, (>250W) NAPE76A/02 195-3030-05 37338
A13 DC-DC Power Supply PWB Assy NAPS33 195-7030 37338
J01 Conn, Socket, 3 pin, Recessed, 250Vac, 6A JT22 EAC309 82389
J02 Conn, Socket, 3 pin, Recessed, 250Vac, 6A JT22 EAC309 82389
J03 Conn, Recept, Sq Flng, Size 11-4 JQ01 206430-1 09482
LS01 Speaker, 45 Ohm, 2W LP07 30A05Z45 74199
M01 Meter,0-4kW,0-30A,mod%,142ohm,1mA,FSD MD52B 195-9020 37338
P06 MTA, Standard Dust Cover, 4 pin JU02 640551-4 09482
P06 MTA, Keyed Closed End Housing,4 pin,22AWG JU27 644463-4 00779
T01 See Sales Order % % SEE SALES 37338
ORDER
TB01 Terminal Block, 4-pos, Single, FT, 15A JB11 381401104 13150
TB02 See Sales Order % % SEE SALES 37338
ORDER
U01 Display Mod 195-3019 195-3019 37338
U02 PS,Univ. Input, 24V,150W,EXTTemp, AC/IP Grounded UB53 MIW150- 3AC42
P4841(STATIC)
U03 See Master Work Order * * SEE MASTER 37338
WORK ORDER
U04 See Sales Order % % SEE SALES 37338
ORDER
U05 Rect/Assy, Bridge, 800V, 35A UF28 GBPC3508 LITEON
Page 6 of 82 NAE89
NAH54A Combiner/Probe Assy (1 Input)
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
A01 RF Power Probe (VECTOR) PWBAssy NAPF07A/01 195-6020-02 37338
J01 Conn, Coax, N, Recept, Panel,50ohm JDP21 UG58A/U 02660
J05 Conn, Coax, N, Recept, Panel,50ohm JDP21 UG58A/U 02660
Page 7 of 82 NAP33A
NAPC147B Control Display PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
BT01 Battery, Lithium, 3V,20mm Coin Cell BBLT01 CR2032 PANAS
C001 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C002 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C003 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C004 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C005 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C006 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C007 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C008 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C009 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C010 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C011 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C012 Cap,SMT,Ceramic,0.001uF,10%,50V,X7R,0603 CCFS01 C0603C102K5RAC 31433
C013 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C014 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C015 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C016 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C017 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C018 Cap,SMT,Ceramic,0.001uF,10%,50V,X7R,0603 CCFS01 C0603C102K5RAC 31433
C019 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C020 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C021 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C022 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C023 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C024 Cap,SMT,Ceramic,0.001uF,10%,50V,X7R,0603 CCFS01 C0603C102K5RAC 31433
C025 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C026 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C027 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C028 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C029 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C030 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C031 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C032 Cap,SMT,Ceramic,0.0022uF,10%,50V,X7R,0603 CCFS02 C0603C222K5RAC 31433
C033 Cap,SMT,Ceramic,0.0047uF,10%,50V,X7R,0603 CCFS03 C0603C472K5RAC 31433
C034 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C035 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C036 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C037 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C038 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
Page 8 of 82 NAPC147B
Continued from previous page
Page 9 of 82 NAPC147B
Continued from previous page
Page 10 of 82 NAPC147B
Continued from previous page
Page 11 of 82 NAPC147B
Continued from previous page
Page 12 of 82 NAPC147B
Continued from previous page
Page 13 of 82 NAPC147B
Continued from previous page
Page 14 of 82 NAPC147B
Continued from previous page
Page 15 of 82 NAPC147B
Continued from previous page
Page 16 of 82 NAPC147B
Continued from previous page
Page 17 of 82 NAPC147B
Continued from previous page
Page 18 of 82 NAPC147B
Continued from previous page
Page 19 of 82 NAPC147B
Continued from previous page
Page 20 of 82 NAPC147B
Continued from previous page
Page 21 of 82 NAPC147B
NAPC148 Control Interface PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C02 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C03 Cap,SMT,Tantalum,10uF,10%,35V,2917 CTFS03 T494D106K035AS 31433
C04 Cap,SMT,Ceramic,18pF,2%,50V,C0G,0603 CCFS23 C0603C180G5GAC 31433
C05 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C06 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C07 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C08 Cap,SMT,Ceramic,18pF,2%,50V,C0G,0603 CCFS23 C0603C180G5GAC 31433
C09 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C10 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C11 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C12 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C13 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C14 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C15 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C16 Cap,SMT,Tantalum,1uF,10%,35V,1411 CTFS02 T494B105K035AS 31433
C17 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C18 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C19 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C20 Cap,SMT,Tantalum,1uF,10%,35V,1411 CTFS02 T494B105K035AS 31433
C21 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C22 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C23 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C24 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C25 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C26 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C27 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C28 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C29 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C30 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C31 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C32 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C33 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C34 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C35 Cap,SMT,Tantalum,1uF,10%,35V,1411 CTFS02 T494B105K035AS 31433
C36 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C37 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C38 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
CR01 Diode,SMT,Switching,250V,0.2A,SOD-323 QDRS01 BAS21HT1(STATIC) 04713
Page 22 of 82 NAPC148
Continued from previous page
Page 23 of 82 NAPC148
Continued from previous page
Page 24 of 82 NAPC148
NAPE76A/00 Exciter Monitor/GeneratorPWB Assy, Basic
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C02 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C03 Cap,SMT,Ceramic,0.047uF,10%,50V,X7R,0603 CCFS06 C0603C473K5RAC 31433
C04 Cap,SMT,Ceramic,10uF,20%,6.3V,X5R,0805 CCFS57 C2012X5R0J106M 54583
C05 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C06 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C07 Cap,SMT,Tantalum,10uF,10%,16V,1411 CTFS01 T494B106K016AS 31433
C08 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C09 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C10 Cap,SMT,Ceramic,0.001uF,10%,50V,X7R,0603 CCFS01 C0603C102K5RAC 31433
C11 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C12 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C13 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C14 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C15 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C16 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C17 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C18 Cap,SMT,Tantalum,1uF,10%,35V,1411 CTFS02 T494B105K035AS 31433
C19 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C20 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C21 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C22 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C23 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C24 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C25 Cap,SMT,Tantalum,1uF,10%,35V,1411 CTFS02 T494B105K035AS 31433
C26 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C27 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C28 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C29 Cap,SMT,Ceramic,0.47uF,10%,25V,X7R,0805 CCFS09 C0805C474K3RAC 31433
C30 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C31 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C32 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C33 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C34 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C35 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C36 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C37 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C38 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C39 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
Page 25 of 82 NAPE76A/00
Continued from previous page
Page 26 of 82 NAPE76A/00
Continued from previous page
Page 27 of 82 NAPE76A/00
Continued from previous page
Page 28 of 82 NAPE76A/00
Continued from previous page
Page 29 of 82 NAPE76A/00
Continued from previous page
Page 30 of 82 NAPE76A/00
NAPE76A/02 Exciter Monitor/GeneratorPWB Assy, (>250W)
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
E01 Conn, Post Shunt, 2 Pos, .10 Centreline JQ15 390088-2 09482
E02 Conn, Post Shunt, 2 Pos, .10 Centreline JQ15 390088-2 09482
E03 Conn, Post Shunt, 2 Pos, .10 Centreline JQ15 390088-2 09482
J01 Conn, Plug, D-Sub, 25 pin, PWB Mt JS12 K22-B25P-NJ 63590
J04 Conn, Header, Ribbon Cbl, 20 pin JP46 499910-4 00779
R63 Resistor, SMT, MF, 1500 Ohms,1% 1/4W RAD27 RK73H2BL1501F 59124
R70 Resistor, SMT, MF, 1500 Ohms,1% 1/4W RAD27 RK73H2BL1501F 59124
XE01 Conn, Header, SIP,12 Pin Breakawy,.10 Ctr JQ16 1-103185-2 09482
XE02 Conn, Header, SIP,12 Pin Breakawy,.10 Ctr JQ16 1-103185-2 09482
XE03 Conn, Header, SIP,12 Pin Breakawy,.10 Ctr JQ16 1-103185-2 09482
Page 31 of 82 NAPE76A/02
NAPF05 RF Filter PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C02 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C03 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C04 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C05 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C06 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C07 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C08 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C09 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C10 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C11 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C12 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C13 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C14 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C15 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
C16 Capacitor,Polyprop,0.0036uF,3%,900VAC CP29 715P3623900L-1138 SBE
E01 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E02 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E03 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E04 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E05 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E06 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E07 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E08 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E09 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E10 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E11 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E13 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E14 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E16 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E18 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E19 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E22 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E23 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E24 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E25 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E26 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E27 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E28 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
Page 32 of 82 NAPF05
Continued from previous page
Page 33 of 82 NAPF06
NAPF07A/00 RF Power Probe PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Mica, Dipped,1800pF 2% 500V CB40 CM06FD182G03 14655
C02 Capacitor, Mica, Dipped,1800pF 2% 500V CB40 CM06FD182G03 14655
C03 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
C04 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR01 Diode,Schottky,100V,0.1A,DO-35 QK48 BAT41(STATIC) U3040
CR02 Diode,Schottky,100V,0.1A,DO-35 QK48 BAT41(STATIC) U3040
CR03 Diode,Schottky,100V,0.1A,DO-35 QK48 BAT41(STATIC) U3040
CR04 Diode,Schottky,100V,0.1A,DO-35 QK48 BAT41(STATIC) U3040
CR05 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR06 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR07 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR08 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR09 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
E01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
E02 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
E03 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
E04 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
J01 Conn, Socket, D-Sub, 25 pin, PWB Mt JS13 K22-B25S-NJ 22421
J02 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
L01 Inductor, Moulded, Shielded, 10000uH LAP41 IMS-5-10000UH+/- 35005
10%
L02 Inductor, Moulded, Shielded, 10000uH LAP41 IMS-5-10000UH+/- 35005
10%
L03 Inductor, Moulded, Shielded, 10000uH LAP41 IMS-5-10000UH+/- 35005
10%
L04 Inductor, Moulded, Shielded, 10000uH LAP41 IMS-5-10000UH+/- 35005
10%
R01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
R02 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
R03 Resistor, Film, 1000 Ohms, 5%, 2W RBP13 GS-3, 1000 OHMS 75042
R04 Resistor, Film, 1000 Ohms, 5%, 2W RBP13 GS-3, 1000 OHMS 75042
R05 Resistor, Film, 1000 Ohms, 5%, 2W RBP13 GS-3, 1000 OHMS 75042
R06 Resistor, Film, 1000 Ohms, 5%, 2W RBP13 GS-3, 1000 OHMS 75042
R07 Resistor, Film, 1000 Ohms, 5%, 2W RBP13 GS-3, 1000 OHMS 75042
Page 34 of 82 NAPF07A/00
Continued from previous page
Page 35 of 82 NAPF07A/01
NAPI76 Exciter Interface PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C02 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C03 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C04 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C05 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C06 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C07 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C08 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C09 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C10 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C11 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C12 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C13 Capacitor, Ceramic, 0.0022uF 10% 100V CCG02 CKR05BX222KRV 56289
C14 Capacitor, Ceramic, 0.0022uF 10% 100V CCG02 CKR05BX222KRV 56289
C15 Capacitor, Mica, Dipped, 2200pF 2% 500V CB41 CM06FD222G03 14655
C16 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C17 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C18 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C19 Capacitor, Ceramic, 0.0022uF 10% 100V CCG02 CKR05BX222KRV 56289
C20 Capacitor, Ceramic, 0.0022uF 10% 100V CCG02 CKR05BX222KRV 56289
C21 Capacitor, Mica, Dipped, 2200pF 2% 500V CB41 CM06FD222G03 14655
C22 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C23 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C24 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C25 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C26 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C27 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C28 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
CR01 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
CR02 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
CR03 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
CR04 Diode, Pwr Rectifier, 200V,15A, Ultrafast QM42 MUR1520(STATIC) ONSEMI
CR05 Diode, Power Rectifier, 200V 1A QN38 MUR120 04713
CR06 Diode, Power Rectifier, 200V 1A QN38 MUR120 04713
CR07 Diode, Pwr Rectifier, 200V,15A, Ultrafast QM42 MUR1520(STATIC) ONSEMI
Page 36 of 82 NAPI76
Continued from previous page
Page 37 of 82 NAPI76
Continued from previous page
Page 38 of 82 NAPI76
Continued from previous page
Page 39 of 82 NAPI76
Continued from previous page
Page 40 of 82 NAPI76
NAPI78A Remote Interface, Basic
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C001 Cap,SMT,Ceramic,0.0022uF,10%,50V,X7R,0603 CCFS02 C0603C222K5RAC 31433
C002 Cap,SMT,Ceramic,0.0047uF,10%,50V,X7R,0603 CCFS03 C0603C472K5RAC 31433
C003 Cap,SMT,Tantalum,10uF,10%,35V,2917 CTFS03 T494D106K035AS 31433
C004 Cap,SMT,Ceramic,1000pF,2%,50V,C0G,0805 CCFS42 C0805C102G5GAC 31433
C005 Not Used - NOT USED 37338
C006 Cap,SMT,Ceramic,1000pF,2%,50V,C0G,0805 CCFS42 C0805C102G5GAC 31433
C007 Cap,SMT,Ceramic,1000pF,2%,50V,C0G,0805 CCFS42 C0805C102G5GAC 31433
C008 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C009 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C010 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C011 Not Used - NOT USED 37338
C012 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C013 Cap,SMT,Tantalum,10uF,10%,35V,2917 CTFS03 T494D106K035AS 31433
C014 Not Used - NOT USED 37338
C015 Cap,SMT,Ceramic,150pF,1%,50V,C0G,0603 CCFS33 0603A151FAT2A 56289
C016 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C017 Capacitor, Ceramic, 1.0uF 10%50V CCG10 CKR06BX105KRV 56289
C018 Not Used - NOT USED 37338
C019 Not Used - NOT USED 37338
C020 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C021 Cap,SMT,Tantalum,10uF,10%,35V,2917 CTFS03 T494D106K035AS 31433
C022 Cap,SMT,Ceramic,150pF,1%,50V,C0G,0603 CCFS33 0603A151FAT2A 56289
C023 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C024 Not Used - NOT USED 37338
C025 Not Used - NOT USED 37338
C026 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C027 Not Used - NOT USED 37338
C028 Not Used - NOT USED 37338
C029 Cap,SMT,Tantalum,10uF,10%,16V,1411 CTFS01 T494B106K016AS 31433
C030 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C031 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C032 Not Used - NOT USED 37338
C033 Not Used - NOT USED 37338
C034 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C035 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C036 Cap,SMT,Tantalum,10uF,10%,35V,2917 CTFS03 T494D106K035AS 31433
C037 Not Used - NOT USED 37338
C038 Not Used - NOT USED 37338
C039 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
Page 41 of 82 NAPI78A
Continued from previous page
Page 42 of 82 NAPI78A
Continued from previous page
Page 43 of 82 NAPI78A
Continued from previous page
Page 44 of 82 NAPI78A
Continued from previous page
Page 45 of 82 NAPI78A
Continued from previous page
Page 46 of 82 NAPI78A
Continued from previous page
Page 47 of 82 NAPI78A
Continued from previous page
Page 48 of 82 NAPI78A
Continued from previous page
Page 49 of 82 NAPI78A
Continued from previous page
Page 50 of 82 NAPI78A
Continued from previous page
Page 51 of 82 NAPI78A
NAPI79 DGPS Site Interface PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C001 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C002 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C003 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C004 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C005 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C006 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C007 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C008 Cap,SMT,Tantalum,10uF,10%,35V,2917 CTFS03 T494D106K035AS 31433
C009 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C010 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C011 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C012 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C013 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C014 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C015 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C016 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C017 Cap,SMT,Ceramic,0.01uF,10%,50V,X7R,0603 CCFS04 C0603C103K5RAC 31433
C018 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C019 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C020 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C021 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C022 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C023 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C024 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C025 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C026 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C027 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C028 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C029 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C030 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C031 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C032 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C033 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C034 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C035 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C036 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C037 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C038 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
C039 Cap,SMT,Ceramic,0.1uF,10%,50V,X7R,0805 CCFS07 C0805C104K5RAC 31433
Page 52 of 82 NAPI79
Continued from previous page
Page 53 of 82 NAPI79
Continued from previous page
Page 54 of 82 NAPI79
Continued from previous page
Page 55 of 82 NAPI79
Continued from previous page
Page 56 of 82 NAPI79
Continued from previous page
Page 57 of 82 NAPI79
Continued from previous page
Page 58 of 82 NAPI79
Continued from previous page
Page 59 of 82 NAPI79
Continued from previous page
Page 60 of 82 NAPI79
Continued from previous page
Page 61 of 82 NAPI81
NAPM11 Interphase PDM Driver PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C02 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C03 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C04 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C05 Capacitor, Ceramic, 0.22uF 10% 50V CCG08 CKR06BX224KRV 56289
C06 Capacitor, Mica, Dipped, 470pF 2% 500V CB33 CD15FD471G03 14655
C07 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C08 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C09 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C10 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C11 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C12 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C13 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C14 Capacitor, Mica, Dipped, 100pF 2% 500V CB25 CM05FD101G03 SOSH
C15 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C16 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C17 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C18 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C19 Capacitor, Mica, Dipped, 470pF 2% 500V CB33 CD15FD471G03 14655
C20 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C21 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C22 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C23 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C24 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C25 Capacitor, Mica, Dipped, 100pF 2% 500V CB25 CM05FD101G03 SOSH
C26 Capacitor, Ceramic, 0.047uF 10% 100V CCG06 CKR06BX473KRV 56289
C27 Capacitor, Mica, Dipped, 330pF 2% 500V CB31 CM05FD331G03 14655
C28 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C29 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C30 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C31 Not Used - NOT USED 37338
C32 Not Used - NOT USED 37338
C33 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C34 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C35 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
Page 62 of 82 NAPM11
Continued from previous page
Page 63 of 82 NAPM11
Continued from previous page
Page 64 of 82 NAPM11
Continued from previous page
Page 65 of 82 NAPM11
Continued from previous page
Page 66 of 82 NAPM11
Continued from previous page
Page 67 of 82 NAPM11
NAPS31A/00 SMPS, Fwd Converter PWBAssy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Ceramic, 0.001uF 10% 200V CCG01 CKR05BX102KRV 91929
SPRAGUE
C02 Capacitor, Ceramic, 1.0uF 100V CAP16 RPE114Z5U105M100 91929
V
C03 Not Used - NOT USED 37338
C04 Capacitor,Polypro,0.015uF800Vac CT39 715P1535800L SBE
C05 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C06 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C07 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C08 Capacitor, Ceramic, Coated, 2.2uF 20% 50V CCG45 C340C225M5R5CA 91929
C09 Capacitor, Ceramic, Y, 0.01uF250VAC CCG44 DE1607F103M-KH MURATA
C10 Capacitor, Ceramic, 1.0uF 100V CAP16 RPE114Z5U105M100 91929
V
C11 Capacitor, Ceramic, Y, 0.01uF250VAC CCG44 DE1607F103M-KH MURATA
C12 Capacitor, Electrolytic, 470uF450V CBP15 381LR471M450A052 14655
CORNELL
C13 Capacitor, Electrolytic, 470uF450V CBP15 381LR471M450A052 14655
CORNELL
C14 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C15 Capacitor, Electrolytic, 470uF450V CBP15 381LR471M450A052 14655
CORNELL
C16 Capacitor, Ceramic, 0.001uF 10% 200V CCG01 CKR05BX102KRV 91929
SPRAGUE
C17 Capacitor, Metal,Polyprop, 5uF +/-20% 600V CT40 734G505X0600 DEARBO
C18 Capacitor, Ceramic, 1.0uF 100V CAP16 RPE114Z5U105M100 91929
V
C19 Capacitor, Mica, Dipped, 470pF 2% 500V CB33 CD15FD471G03 14655
C20 Capacitor, Dipped Mica, 220pF5% 1000V CT16 CDV18FF221J03 14655
C21 Capacitor, Dipped Mica, 220pF5% 1000V CT16 CDV18FF221J03 14655
C22 Capacitor, Ceramic, 0.001uF 10% 200V CCG01 CKR05BX102KRV 91929
SPRAGUE
C23 Capacitor, Dipped Mica, 220pF5% 1000V CT16 CDV18FF221J03 14655
C24 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C25 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C26 Capacitor, Mica, Dipped, 1000pF 2% 500V CB37 CM06FD102G03 14655
C27 Capacitor, Metal,Polyprop, 5uF +/-20% 600V CT40 734G505X0600 DEARBO
C28 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C29 Capacitor, Ceramic, 1.0uF 100V CAP16 RPE114Z5U105M100 91929
V
C30 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C31 Capacitor, Ceramic, 2700pF, 1%, 100V CAP47 C052C272F1G5CA 91929
C32 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C33 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C34 Capacitor, Ceramic, 0.001uF 10% 200V CCG01 CKR05BX102KRV 91929
SPRAGUE
Page 68 of 82 NAPS31A/00
Continued from previous page
Page 69 of 82 NAPS31A/00
Continued from previous page
Page 70 of 82 NAPS31A/00
Continued from previous page
Page 71 of 82 NAPS31A/00
Continued from previous page
Page 72 of 82 NAPS31A/00
NAPS31A/01 SMPS, Fwd Conv,(Vector)PWBAssy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
E01 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E02 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
J01 Conn, Header, Ribbon Cbl, 20 pin JP46 499910-4 00779
J03 Conn, Pin Header,3-Pin,Mate-N-Lok, Vert JT65 641966-1 09482
Page 73 of 82 NAPS31A/01
NAPS32 LVPS Buck Converter PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Elect, 1000uF 50V CT41 SME50VB102M16X25 1W344
LL
C02 Capacitor, Elect, 1000uF 50V CT41 SME50VB102M16X25 1W344
LL
C03 Capacitor, Elect, 1000uF 50V CT41 SME50VB102M16X25 1W344
LL
C04 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C05 Capacitor, Elect, 100uF 20% 25V CAP42 KME25VB101M6X11L 1W344
L
C06 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C07 Capacitor, Elect, 1000uF 50V CT41 SME50VB102M16X25 1W344
LL
C08 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C09 Capacitor, Elect, 1000uF 50V CT41 SME50VB102M16X25 1W344
LL
C10 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C11 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C12 Capacitor, Elect, 1000uF 50V CT41 SME50VB102M16X25 1W344
LL
C13 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C14 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C15 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C16 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C17 Not Used - NOT USED 37338
C18 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C19 Capacitor, Ceramic, 0.01uF 10% 100V CCG04 CKR05BX103KRV 56289
C20 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C21 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C22 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C23 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C24 Capacitor, Ceramic, 0.47uF 10% 50V CCG09 CKR06BX474KRV 56289
C25 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C26 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
CR01 Diode, Pwr Rectifier, 200V,15A, Ultrafast QM42 MUR1520(STATIC) ONSEMI
CR02 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR03 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR04 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR05 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR06 Diode, Power Rectifier, 200V 1A QN38 MUR120 04713
CR07 Diode, Schottky Rectifier, 45V, 16A QM43 MBR1645(STATIC) ONSEMI
Page 74 of 82 NAPS32
Continued from previous page
Page 75 of 82 NAPS32
Continued from previous page
Page 76 of 82 NAPS32/01
NAPS33 DC-DC Power Supply PWB Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Tantalum, Dipped, 10uF, 35V CCP36 T351G106K035AT(Ro 96095
HS) KEMET
C02 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C03 Capacitor, Ceramic, 1.0uF 10%50V CCG10 CKR06BX105KRV 56289
C04 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C05 Capacitor, Ceramic, 1.0uF 10%50V CCG10 CKR06BX105KRV 56289
CR01 Diode, Pwr Rectifier, 200V,15A, Ultrafast QM42 MUR1520(STATIC) ONSEMI
CR02 Diode, Pwr Rectifier, 200V,15A, Ultrafast QM42 MUR1520(STATIC) ONSEMI
CR03 Diode, General Purpose, 400V,1A QE28 1N4004 04713
CR04 Diode, Zener Transient Supressor, 30V QM12 P6KE30CA 04713
J01 MTA, Keyed Square Post HeaderAssy, 4 pin JU25 647123-4 00779
J02 MTA, Keyed Square Post HeaderAssy, 4 pin JU25 647123-4 00779
L01 Transformer Assy, Servo Probe 195-9535 195-9535 37338
R01 Resistor, MF, 182 Ohms, 1PC 1/4W RAB16 MF1/4DL1820F 59124
R02 Resistor, MF, 121 Ohms, 1%, 1/4W RAB14 MF1/4DL1210F 59124
R03 Resistor, MF, 562 Ohms, 1PC 1/4W RAB22 MF1/4DL5620F 59124
R04 Resistor, Wirewound, 1 Ohms, 1%, 2.5W, NH RS44 NS-2C-1 OHM-1% 35005
U01 Voltage Regulator, Adj Voltage, 3A UT36 LM350T 27014
U02 Voltage Regulator, Adj Voltage, 3A UT36 LM350T 27014
Page 77 of 82 NAPX32/01
NARB17 Final Assy, Vector
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
A01 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A02 Exciter Control Assy, Vector NAE89 195-3000 37338
A03 RF Power Block Assy NAX234A 195-5000-01 37338
A04 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A05 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A06 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A07 See Sales Order % % SEE SALES 37338
ORDER
A08 See Master Work Order * * SEE MASTER 37338
WORK ORDER
J01 Conn, Coax, N, Adaptor, 50ohm, J/J JA05 UG30D/U 02660
W1P1 Conn, Coax, N, Plug, 50ohm, RG213 JA19 UG21C/U 02660
W1P2 Conn, Coax, N, Plug, 50ohm, RG213 JA19 UG21C/U 02660
Page 78 of 82 NARB17
NASM11A/00 Modulator Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
C01 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C02 Capacitor, Tantalum, 6.8uF 10PC 35V CCP19 CSR13F685KM 56289
C03 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C04 Capacitor, Electrolytic, 470uF450V CBP15 381LR471M450A052 14655
CORNELL
C05 Capacitor, Electrolytic, 470uF450V CBP15 381LR471M450A052 14655
CORNELL
C06 Capacitor, Electrolytic, 470uF450V CBP15 381LR471M450A052 14655
CORNELL
C07 Capacitor, Tantalum, 6.8uF 10PC 35V CCP19 CSR13F685KM 56289
C08 Capacitor, Polyprop, 0.12uF,5%, 600V CT44 715P12456MA3 SBE
C09 Capacitor, Ceramic, 0.1uF 10%100V CCG07 CKR06BX104KRV 56289
C10 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR01 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
CR02 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
CR03 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
CR04 Diode, General Purpose, 200V,0.1A QAP29 1N4938 07263
CR05 Diode, Zener, 13V, 1W, 10% QK19 1N4743 04713
CR06 Diode, Power Rectifier, 4A, Ultra Fast QM22 MUR460 04713
CR07 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR08 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR09 Diode, Zener Transient Supressor, 20V QI29 P6KE20CA 07263
CR10 Diode, Zener Transient Supressor, 20V QI29 P6KE20CA 07263
CR11 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
CR12 Diode, General Purpose, 400V,1A QE28 1N4004 04713
CR13 Diode, Zener Transient Supressor, 20V QI29 P6KE20CA 07263
DS01 Diode, LED, Yellow, 8.6mm Lg QM19 SSL-LX5093YD 1EM90
E01 Connector, Quick-Dis, M,1/4 Tab, PWB HR26 1287 91833
E02 Connector, Quick-Dis, M,3/16 Tab PWB HAM52 1212 91833
J01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
J02 Conn, Header, Ribbon Cbl, 10 pin JA49 499910-1 00779
L01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
Q01 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
Q02 Installed at Next Higher Assy + INSTALLED AT NEXT 37338
HIGHER ASSY
R01 Resistor, MF, 33.2 Ohms, 1PC 1/4W RAB07 MF1/4DL33R2F 59124
R02 Resistor, Film, 68K Ohms, 5%,2W RBP24 GS-3, 68K OHMS 75042
R03 Resistor, Film, 68K Ohms, 5%,2W RBP24 GS-3, 68K OHMS 75042
Page 79 of 82 NASM11A/00
Continued from previous page
Page 80 of 82 NASM11A/01
NAX233/01 AC Power Distribution Panel
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
CR01 Diode, General Purpose, 400V,1A QE28 1N4004 04713
F01 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
F02 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
F03 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
F04 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
F05 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
F06 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
F07 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
F08 Fuse, 12A, 500VDC, Non Time Delay, KLM FA33 KLM12 71400
J01 Conn,Socket,AC Panel Outlet,250V,16A JS62 6653.3100(RoHS) SCHURTE
J02 Conn,Socket,AC Panel Outlet,250V,16A JS62 6653.3100(RoHS) SCHURTE
J03 Conn, AC Panel Outlet/Socket,250V/15A JDP45 66000-3300 61935
J04 Conn, AC Panel Outlet/Socket,250V/15A JDP45 66000-3300 61935
J11 Conn, Recept, Sq Flng, Size 11-4 JQ01 206430-1 09482
K01 Relay,24 VDC Coil,DPDT,50 Amps,High Power KC55 199PX-13 MAGCRFT
L01 Choke, 2.5mH, 10A TC46 CHC159ZL-N ATC-FROS
L02 Choke, 2.5mH, 10A TC46 CHC159ZL-N ATC-FROS
RT01 Thermistor,Megasurge,20Ohm,10A RX48 MS3220010 021P3
RT02 Thermistor,Megasurge,20Ohm,10A RX48 MS3220010 021P3
T01 Xfmr,Pwr,Toroidal,1Ph,115/230,300VA TD47 182M117(STATIC) 73831
TB01 Terminal Block, 6-pos, Double, 30A JB06 382100106 13150
TB02 Terminal Block, 6-pos, Double, 30A JB06 382100106 13150
TB03 Terminal Block, 4-Pos, Double, 61A JF27 G10/4 5Y407
TB04 Terminal Block, 4-pos, Double, 30A JB33 382100104 13150
U01 Filter, AC Line, 20A, 250Vac,50/60Hz UC54 20VP6 05245
XF01 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
XF02 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
XF03 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
XF04 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
XF05 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
XF06 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
XF07 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
XF08 Fuseholder, 30A, 600V, Type MDA5 BA43 571007 75915
Page 81 of 82 NAX233/01
NAX234A RF Power Block Assy
REFDES DESCRIPTION NAUTEL # VENDOR # OEM CODE
A01 RF Power Module Assy, Vector NAP33A 195-1000-01 37338
A02 See Master Work Order * * SEE MASTER 37338
WORK ORDER
A03 Not Used - NOT USED 37338
A04 Power Block Back Plane PWB NAPI81 195-8020 37338
A05 RF Filter PWB Assy NAPF05 195-6050 37338
A06 RF Transformer PWB Assy NAPX32/01 195-5040-01 37338
K01 Relay,24Vdc,DPDT,25A KA55 W389CX-8(RoHS) MAGNECR
U01 Rect/Assy, Bridge, 800V, 35A UF28 GBPC3508 LITEON
Page 82 of 82 NAX234A
Vector DGPS Transmitter
TECHNICAL INSTRUCTION MANUAL
Connector Mate
W1P1 A1J5 (RF Out)
W1P2 J1 (Xmtr RF Out)
*** - Denotes used when NDB site interface PWB (A4) is purchased
Connector Mate
P1 A7 DC OUT
P7 A8 AC A
P8 A8 AC B
W1P1 EXCTR/PWR BLK 1
W1P2 EXCTR/PWR BLK 2
W1P3 A4J4
W1P4 A4J5
W2P1 A1 RF IN
W2P2 A5J1
Connector Mate
P2 A2J3
P3 A2J2
P4 A5J1
P5 A1J3
W1P1 A1J2
W1P2 A5J2
W2P1 A1J4
W2P2 A3J1
W3P1 A1J6
W3P2 A2J1
NOTE:
NOTE:
** - used only in NAX233/04 versions (VRD3000 transmitters)
NOTES
** - Denotes wire used only on NAX235/02 variations.
NOTES
** - Denotes wire used only on NAX235/02 variations.
A2W13P1 A2W14P1
LINE 1 1 GND REF
* ** *** ****
LINE 2 2 A2W13P2 A2W14P2 AC VOLTS
A8 AC VOLTS AC VOLTS AC VOLTS
AC LINE A B AC POWER A B A B A B
NEUTRAL 3 DISTRIBUTION A2W11P2
J3 J4 PANEL J5 J6 J7 J8 J9 J10 1 FWD PWR SAMPLE
GND 4 J1 J2 A1 2
A2W12 COMBINER/
A3J12 P1 P2 A3P7 A3P8 A4P7 A4P8 A5P7 A5P8 A6P7 A6P8 PROBE 5 REFLD PWR SAMPLE
A2W11P1 +24V 19 2 6
FWD PWR SAMPLE 1 J11 RF IN (4)
# AC ENABLE - 20 3 9 RF VOLTS MONITOR
2 A6W2 A1J1
W1P1 W1P3 W1P1 W1P3 W1P1 W1P3 W1P1 W1P3 10
REFLD PWR SAMPLE 5 1 # RELAY CONTROL B - 1 1 # RELAY CONTROL B - 1 1 # RELAY CONTROL B - 1 1 # RELAY CONTROL B - 1 A5J1 P1 P2 J4
**** 13 RF CURR MONITOR
6 2 GND 2 2 GND 2 2 GND 2 2 GND 2
14
RF VOLTS MONITOR 9 3 # INHIBIT PDM (A) - 3 3 # INHIBIT PDM (A) - 3 3 # INHIBIT PDM (A) - 3 3 # INHIBIT PDM (A) - 3
A3J11 4 # INHIBIT PDM (B) - 4 4 # INHIBIT PDM (B) - 4 4 # INHIBIT PDM (B) - 4 4 # INHIBIT PDM (B) - 4 17 RF CURR SAMPLE
10 A5W2P2 J3
6 +24V (A) 6 6 +24V (A) 6 6 +24V (A) 6 6 +24V (A) 6
*** 18
RF CURRENT MONITOR 13 SAFETY GND
7 +24V (A) 7 7 +24V (A) 7 7 +24V (A) 7 7 +24V (A) 7
14 A4W2P2 J2
8 GND 8 8 GND 8 8 GND 8 8 GND 8 **
RF CURRENT SAMPLE 17 9 GND 9 9 GND 9 9 GND 9 9 GND 9
18 10 Fc (A) 10 10 Fc (A) 10 10 Fc (A) 10 10 Fc (A) 10 RF OUTPUT
A3W2P2 J1 J5 W1P1 W1P2 J1
11 11 11 11 11 11 11 11
* (TO ATU)
A2J8 A4J6 A4J6 A4J6 A4J4
N/C 1 12 B+ SAMPLE (A) 12 A4J4 12 B+ SAMPLE (A) 12 A4J4 12 B+ SAMPLE (A) 12 A4J4 12 B+ SAMPLE (A) 12
N/C 2 (PART OF) 13 13 13 13 13 13 13 13
(-)
S1950044 VG (+)
Dimensions = mm (inches)
RF (1) J1 RF INPUTS
VR1000/VRD1500
T1
RF (1) J1
A1
RF INPUTS RF
POWER PROBE
RF (2) J2 PWB
T1
1 4
1T 1T J5 RF OUTPUT
RF INPUTS
2
T2
2 20T 1 4 20T 3 2 40T 1
VRD2250 3 T3 1 R10 J1
17
T1 100 RF CURRENT SAMPLE
4T 80T J1
RF (1) J1 2W 18
R3 R9
4 2
1000
2W 100
2W J1
13
R4 J1 RF CURRENT MONITOR
RF (2) J2 1000 14
2W
RF INPUTS
R5
1000
2W J1
9 RF VOLTS MONITOR
RF (3) J3 R6 R1 R2 J1
1000 100 100 10
2W 2W 2W
R7
1000
2W J1
1 FWD PWR SAMPLE
L3 C2 L4
CR4 CR3 10000μH R11 J1
BAT41 BAT41 1800pF 10000μH 4700 2
VR2000/VRD3000 0.5W
T1
RF (1) J1 J1
5 REFLD PWR SAMPLE
L1 C1 L2
CR1 CR2 10000μH R8 J1
BAT41 BAT41 1800pF 10000μH 4700 6
0.5W
RF (2) J2
RF INPUTS
RF (3) J3
RF (4) J4
S1950045 VB
Dimensions = mm (inches)
S1950047 V2 144 V dc
TO SHEET 2
Dimensions = mm (inches)
P4
J2 L + +24.8V (B) 5
L
E G AC INPUT + +24.8V (B) 6
N OUTPUT J14
N * DENOTES INSTALLED FOR DUAL NDB
- RETURN 7
SAFETY U3 ** DENOTES NOT USED FOR NDB OPERATION
GROUND AC/DC - RETURN 8 *** DENOTES INSTALLED FOR DUAL TRANSMITTER
UNIVERSAL
INPUT
POWER SUPPLY
B +24.8V (B) TO SHEET 1
FROM SHEET 1 +
***
S1950048 V2 - DC INPUT
G
Dimensions = mm (inches)
Dimensions = mm (inches)
DATABUS
4750 TP5 TP32 TP46 TP52 8 19
J8 D3 A12 I/O7
MOSI 4 48 A11 7
AD3 A11 18 D6
CR14 D2 A10 I/O6
BAT54HT1 49 6
AD2 A10 17 D5
A9 I/O5
INTERNAL D1 GND GND GND GND 5
ADDRESS
50 A9
TP27 TP26 AD1 A8 16 D4
SERIAL INTERFACE U22 4 I/O4
DATABUS
D0 A8
ATmega128-16AI AD0 51 A7 3 15 D3
+5V 4 28 A7 I/O3
DI TXD1 A6 2 13 D2
A14 A6 I/O2
R101 1 27 TO SHEET 2 A5 1
681 RO RXD1 A14 A5 12 D1
J7 6 41 A4 26 I/O1
(+) 19 DO/RI A14 A4
2 16 40 A13 11 D0
U6 RE PB.6 A13 A3 25 I/O0
INTERNAL R91 R92 A3
DS36C278TM DE 3 39 A12 A2 24
BUS 221 221 A12 A2 U20
J7 7 23 38 A11
(-) 21 DO/RI XTAL2 A11 A1 23 CY62256LL
ADDRESS A1
ADDRESS
Y1 37 A10 FROM SHEET 2 A0
R100 A10 21
681 11.0592MHz A9 A0
J7 24 36
20 XTAL1 A9
35 A8
5 C125 C126 A8
J7 8 GND 18pF 18pF 22
22 +5V VCC GND
C49 C54 53
0.1 0.01 GND
63
GND
33 27
WR WE
+5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V +5V 34 22
RD OE
14
RD GND
R153 R155 R144 R145 R146 R152 R151 R184 R185 R187 R186 R190
10.0K 10.0K 10.0K 10.0K 10.0K 10.0K 10.0K 10.0K 10.0K 10.0K 10.0K 10.0K RAM MONITOR
TP47 WR J10
J6 17 6 20 +5V 4 PROG VCC
# PWR INCREASE - 11 PB.7 CEO CE C139
43 ALE TO J10
J6 19 ALE 8 1 28 0.01 7 PROG VCC
# PWR DECREASE - 10 PG.4 SHEET 2 +5V VCCI VCCO VCC
C115 C121 U21 3 C112 C111 J8
J6 61 TOL 2 PROG VCC
# SOFTKEY 1 - 16 PF.0 0.1 0.01 DS1312S-2 0.1 0.01
A15
J6 60 4
# SOFTKEY 2 - 15 PF.1 GND +5V
J6 59 42 U24:A 5
# SOFTKEY 3 - 14 PF.2 A15 CEI
1 2
J6 58 R200
# UP KEY -12 PF.3 2 4750
VBAT 7 #LOW_BAT-
J6 29 R250 C120 BW TO SHEET 2
# DOWN KEY - 13 PD.4
100 10
J5 18 35V
# LOCAL - 11 PG.3 BT1
J5 30 3V REAL-TIME CLOCK
# REMOTE -10 PD.5 +5V J5
6 RF ON COMMON
J5 7
VBAT
# RF ON - 7 J5
4 4 R223 9 SWITCH COMMON
J1 31 PE.2 WDI
# EXT RF ON - 16 PD.6 10.0K
14 J6
# RF OFF - 8 J5 32 16 FT/OUT TP51 17 SWITCH COMMON
PD.7 +5V VCC
C137 13 R224 J6
J1 C138 1000 18 SHIELD
# EXT RF OFF - 15 0.01 0.1 THS
11
CR6 CR3 CR7 CR8 CR9 CR5 CR4 CR12 CR13 CR11 CR10 SQW TP49 J8
+5V U25 R225 6 PROG GND
26
INT1 M41T94MQ6 1000
TP48 8 J10
21 R219 VSS 2 PROG GND
+5V VCC
10.0K
L11 C119 C118 20 3 J10
RESET RST 10 PROG GND
0.1 0.01 6
15 RSTIN2
E
10 2
52 SCL XO
+5V VCC 12
FROM SHEET 3 +5V L12 C127 C128 SDI Y2
0.1 0.01 9 32.768kHz
SDO
5 1
RSTIN1 XI
J8
64 3 PROG SCK
+5V AVCC
L10 C116 C117 11 SCK
0.1 0.01 SCK
12 MOSI
MOSI TO
INT0 25 MISO
FROM SHEET 2 INT0 13 SHEET 3
MISO
#EOC- 8 RESET
FROM SHEET 3 INT6 1
PEN
#AC_LOW- 7 10
FROM SHEET 4 INT5 SS RESET
14 TO SHEET 2
INT4 PB.4 +5V
6 15
FROM SHEET 2 OC3B PB.5
62 C165 13
AREF +5V R252 14 J1
J10 57 3920 0.1 U11:D 11 MONITOR
PROG TCK 1 TCK
AMPLIFIER GAIN
J10 56 R251 C164 R254 R255 C166 12
PROG TMS 5 TMS R253
10.0K Q5 0.47 475K 475K 0.1
J10 55 5 2N7002LT1 100K
PROG TDO 3 TDO OC3A
J10 54
PROG TDI 9 TDI
J10
PROG RESET 6
J8
PROG RESET 5
#SS6(RTC)-
FROM SHEET 2
S1950142 SHEET 1 OF 4 V1
Dimensions = mm (inches)
DATABUS
#LOW_BAT- D4 U23:E Q4
ADDRESS
50
23 #SS6(RTC)- D3 5 16 A3
D3 U23:D Q3
TO
#AC_LOW- 71 INT0 D2 4 17 A2
51 SHEET 1 D2 U23:C Q2
#REFLD_PWR_SHUTBACK+ D1 3 18 A1
FROM 52 73 D1 U23:B Q1
SHEET 4 VCC_INT +5V J3 D0 A0
#HIGH_RF_CURRENT+ 55 C103 C104 L7 +5V 1 CPLD VCC 2 19
D0 U23:A Q0
0.1 0.01 C64
0.01
69 11 LATCH 20 A0
#REMOTE_STATUS+ ENABLE VCC +5V
78 J3
VCC_INT +5V 6 CPLD GND U23:I C129 C134
+5V +5V 83 C98 C99 L6 SN74AHC573DW 0.1 0.01
#RF_ON+ 0.1 0.01
1 OUTPUT 10 J4
GND
ENABLE 5 # INHIBIT PM (B) -
+5V R192 R193 U18
FROM +5V +5V +5V 10.0K 10.0K
57 XC9572-15PC84C 1 D7 J4
SHEET 3 4 # INHIBIT PM (A) -
VO(LCD) TP43
GRAPHIC DIGITAL OUTPUTS
R123 R122 R117 58 61 D6 D7 9 12 U30:A J1
TP42
10.0K 10.0K 10.0K DISPLAY D8 U29:H Q8
1 16
9 # REMOTE COMMON -
J3 59 7 D5 D6 U30:B J1
CPLD TDO 5 TDO D7 J9 8
D7 U29:G Q7
13
10 # OPERATING B -
18 D7 2 15
J3 28 67 D4 D5 7 14 U30:C
CPLD TDI 4 TDI D6 J9 D6 U29:F Q6
17 D6 3 14
J3 29 D3 D4 U30:D R163 J6
DATABUS
CPLD TMS 3 TMS 63 D5 J9 6 15
16 D5 D5 U29:E Q5
4 13
6 # CHANGEOVER LED -
J3 30 54 D2 D3 5 16 U30:E 2210 R157 J6
CPLD TCK 2 TCK D4 J9 D4 U29:D Q4 8 # POWER SUPPLY LED -
15 D4 5 12
22 68 D1 D2 4 17 U30:F 2210 R156 J6
+5V +5V +5V +5V +5V +5V +5V +5V VCC_IO D3 J9 D3 U29:C Q3 9 # AC MAINS LED -
L4 14 D3 6 11
C90 C91 70 D0 D1 3 18 U30:G 2210 J5
0.1 0.01 D2 J9 D2 U29:B Q2 4 # RF ON LED -
R9 R27 R8 R198 R174 R196 R205 13 D2 7 10
D0 2 19 +5V R176
R10 4750 4750 4750 4750 4750 4750 4750 U13:A +5V +5V D1 J9 D1 U29:A Q1 2210
J1 4 12 D1
# EXT INTERLOCK OPEN + 29 1 2
100 R28 U13:B D0 J9 R247
J1 5 R149 R150 11 D0
# EXT PDM INHIBIT - 30 11 20 U35:A 4750 U35:B
R7 100 U13:C 3 4 10.0K 10.0K CSOUT1 CLK VCC +5V J5
J1 6 1 16 2 15
5 # RF OFF LED -
# BTRY/MOD PROTN - 31 5 6 U29:I C150 C154 R188
100 R199 U13:D 36
J7 9 TP34 DMF5005NY-LY-AKE SN74AHC574DW 0.1 0.01 2210
# PM FAULT (A)/RF OSC FAIL + 4 9 8 45
R175 100 U14:A TP35 1 OUTPUT 10 #RF_ON+
J7 10 ENABLE GND
# SPARK GAP SHTBCK/SYNTH INSTALLED (A) - 5 1 2
J7 100 R197 U14:B 12 J9 U35:C J6
# PDM LATCH (A) + 6 +5V 3 VCC 7 # EXTERNAL ALARM LED -
3 4 L13 C144 C143 J9 3 14
J7 R206 100 U14:C 14 19 FS R162
# PM INSTALLED (A) -/RF FAIL (A) + 8 0.01 0.1 2210
J9 J6
100 C4 C15 C3 C110 C101 C109 C114 5 6 1 FGND 1 LED COMMON
0.01 0.01 0.01 0.01 0.01 0.01 0.01 J9 J5
38 2 VSS
+15V 3 LED COMMON
+5V VCC_INT J9
L5 20 LED_K C95 C102
+5V +5V +5V +5V +5V +5V +5V C92 C94 R222 0.1 0.1
0.1 0.01 0.0
K D7 9 12 U34:A J1
LED_K D8 U33:H Q8 12 # DCC RMT COM -/RF MON SELECT
R203 R16 R12 R209 R172 R167 R165 1 16
U34:B
4750 4750 4750 4750 4750 4750 4750 D6 8 13 J7
J7 R204 U14:D 17 8 R243 D7 U33:G Q7 32 # INHIBIT RF DRIVE PS +
# LVPS FAIL (A) - 10 GND 2 15
9 8 16 3.92 D5 7 14 U34:C J7
J1 100 R15 U14:E 19 GND 0.5W D6 U33:F Q6 33 # INHIBIT PM (C) -/MED VOLTS +
# MSK ALARM (A) + 13 * DENOTES LINK 3 14
11 10 27 E3:1 D4 6 15 U34:D R164 J6
R11 100 U14:F GND INSTALLED FOR
DATABUS
J1 26 R246 D5 U33:E Q5
4 13
5 # LOW VOLT PS LED -
# KEYER BOARD FAULT (A) + 21 42 VECTOR ONLY U34:E 2210
100 R210 13 12
U15:A
GND 3.92 A * D3 5 16 J7
J7 11 49 0.5W D4 U33:D Q4
5 12
36 # INHIBIT FAN +/SIDE B MAIN -
# PM INSTALLED (C)/SYNTH INSTALLED (B) - 14 GND D2 U34:F
R173 100 U15:B 1 2
60 E3:3 4 17 J7
J7 13 GND R220 E3:2 B D3 U33:C Q3
6 11
35 # HIGH VOLTS +/STANDBY TEST -
# PDM LATCH (B) + 7 A U34:G
3 4 6.81 LED_A D1 3 18 J7
J7 100 R168 U15:C 15 0.5W D2 U33:B Q2 34 # PM RESET -
# RF DRIVE FAIL -/RF FAIL (B) + 9 J9 7 10
U37:A
5 6 +5V 9 LED_A D0 2 19 J7
J7 R166 100 U15:D 18 R221 R238 D1 U33:A Q1 30 # INHIBIT RF DRIVE/MON BYPASS +
# LVPS FAIL (B) - 11 1 16
9 8 6.81 0.0
100 C113 C7 C5 C124 C100 C97 C96 0.5W J9
0.01 0.01 0.01 0.01 0.01 0.01 0.01 +5V +5V A0 8 C/D 11 20
J7 64 CSOUT2 CLK VCC +5V
16 +5V VCC_IO J9
L8 RD 6 RD U33:I C160 C161
J7 C106 C105 R194 R189 +5V
31 +5V +5V +5V +5V +5V +5V +5V 0.1 0.01 J9 SN74AHC574DW 0.1 0.01
10.0K 10.0K WR 5 WR
56 1 OUTPUT 10
TP44 J9 ENABLE GND R248
R23 R26 R215 R213 R158 R207 R4 65 VO(LCD) 4 VEE
4750
TP40 U35:E U35:F J5
R24 4750 4750 4750 4750 4750 4750 4750 U15:E 1 # LOCAL LED -
J1 20 J9 5 12 6 11
# MSK ALARM (B) + 14 11 10
RESET 10 RESET R177
J1 100 R25 U15:F 31 2 LCD_CE J9 2210
# KEYER BOARD FAULT (B) + 22 7 CE
#REMOTE_STATUS+
J7 R216 100 U16:A 13 12
24
# PM FAULT (B) -/SHUTDOWN + 23
100 R214 1 2
U16:B +5V +5V
J7 32 GRAPHIC DISPLAY SHOWN FOR REFERENCE ONLY.
# PDM INSTALLED (A) - 26 D7 9 12 U35:D R178 J5
3 4 D8 U36:H Q8 2 # REMOTE LED -
J7 R159 100 U16:C 37 R191 R160 4 13
# PM INSTALLED (B)/MONITOR FAIL - 15 D6 8 13 U37:C 2210 J7
5 6 10.0K 10.0K D7 U36:G Q7 17 # EXCITER B -
J7 100 R208 U16:D 40 62 3 14
# ACTIVE SIDE B - 24 TP41 D5 U37:D
9 8 84 7 14 J7
R3 100 U16:E TP37 D6 U36:F Q6 18 # RESET PDM -
J1 34 4 13
U37:E R169
DATABUS
# STANDBY CODE 1 - 39 21 INT4 D4 6 15 J6
100 C13 C14 C135 C131 C93 C123 C2 11 10 TO SHEET 1 D5 U36:E Q5
5
4 # EXCITER LED -
0.01 0.01 0.01 0.01 0.01 0.01 0.01 D3 5 16 U38:A R170 12 2210 J6
J1 D4 U36:D Q4 3 # PA LED -
18 72 1 16
CSOUT1 D2 4 17 U38:B 2210 R171 J6
J1 D3 U36:C Q3 2 # OUTPUT NETWORK LED -
32 +5V +5V +5V +5V +5V +5V +5V 74 U38:C 2 15
2210
CSOUT2 D1 3 18 J1
D2 U36:B Q2 3 14
1 # AC ENABLE -
75 U38:D
R1 R217 R211 R13 R128 R130 R115 CSOUT3 D0 2 19 J1
4750 4750 4750 4750 4750 4750 4750 D1 U36:A Q1 2 # DC INHIBIT -
J1 R2 U16:F 43 TP38 4 13
# DC INSTALLED - 40 13 12
J7 100 R218 U17:A 25 J7 11 20
# PM FAULT (C) -/CHANGEOVER ALM + 25 1 2
1 # SHUTBACK (A) - CSOUT3 CLK VCC +5V
J7 R212 100 U17:B 33 C107 C162 C163
# PDM INSTALLED (B) - 27 0.1 U36:I
3 4 81 Q1 SN74AHC574DW 0.1 0.01
J1 100 R14 U17:C 39
# CHARGER ALARM - 17 MMBT4401LT1 1 OUTPUT 10
5 6 R183 GND
#STANDBY_2- R129 100 U17:D 1000 TP39 ENABLE
41
FROM 9 8
#RMT_RF_ON+ 100 R131 U17:E 35 J7
SHEET 1 2 # SOFTSTART/SHUTBACK (B) -
R116 100 U17:F 11 10 C108
J4 44 0.1
# SPARE DIGITAL IN 5 3 82 Q2
100 C1 C136 C130 C6 C70 C71 C61 13 12
MMBT4401LT1 J7
0.01 0.01 0.01 0.01 0.01 0.01 0.01 R195 3
S1950142 SHEET 2 OF 4 V1 1000
Dimensions = mm (inches)
J4
9 U35:H 8 +5V 25 +5V
COM GND L3 C77
MC1413BD J4 C76
+5V 27 10 0.01
J4 35V
7
24
J4
26
+5V +5V
TP12
4 U27:E 11
+15V VCC VEE -15V R136 R135 J4
MC33074AD +15V 17 +15V
C148 C149 10.0K 10.0K L2
12 J4 C67 C62
0.1 10 12 8 9 13 14 0.1 A10 +15V 19 10 0.01
11 J4 35V
A9 16
TP3 2 J4
18
1 9
U2:A A8
+5V
14
VCC
U13:G
GND
7
+15V R59 ANALOG TO DIGITAL TP18
SN74AHCT14D
C83 R37 R38 C19 3 100 U9 CONVERTERS J4
0.1 39.2K 0.1 TLC1543IDW +24V 15 +24V
11 13 10.0K L1
J4 C47 C48
CHARGER_CURRENT 14 10 0.01
8 20 35V
A7 VCC +5V J4
FWD_PWR_SAMPLE C63 C58 10
7
A6 0.01 0.1 TP20
14 U14:G 7
+5V VCC GND REFLD_PWR_SAMPLE 6
SN74AHCT14D A5 J4
C84 -15V 23 -15V
0.1 FROM AC_SAMPLE 5 L9
A4 J4 C122 C132
SHEET 4 10 22 10
PDM_A_SAMPLE GND 0.01
2 35V
A1 13 +5V TO SHEETS 1, 2 & 4
PDM_B_SAMPLE REF-
1
14 U15:G 7 A0 +15V TO SHEET 4
+5V VCC GND POLARITY_ERROR
SN74AHCT14D 4 J4
C85 A3 40 U10
4 6
0.1 +5V VIN LT1790BIS6-4.096 VOUT VREF
+5V C74 C72 C73
GND1 GND2
0.1 10 0.1
1 2
R107 +5V 35V
10.0K
14 U16:G 7
+5V VCC GND 3
SN74AHCT14D A2 R154
C86
0.1 10.0K
#EOC-
MOSI
17
ADDRESS EOC
19 DIGITAL TO ANALOG
MOSI CR2
FROM SCK
18
I/O_CLK BAT54HT1 TO CONVERTER
SHEET 1 SHEET 1 14
14 U17:G 7 SCK 14 MISO +5V VDD 12 REFLD_PWR_SHTBK_REF
+5V VCC GND VREF REF+ 16 L15 C153 C156 DACA
SN74AHCT14D DATA_OUT
C89 #SS1(ADC1)- 15 0.1 0.01 U31 11 LOW_AC_REF TO
CS TLV5620ID DACB
0.1 SHEET 4
10 RF_CURRENT_REF
FROM 6 DACC
MOSI DATA
SHEET 2 7 1
#SS2(ADC2)- SCK CLK GND TP50
9 U38:H 8 15 13
COM GND CS #SS4(DAC1)- LDAC
MC1413BD 8
CR16 FROM SHEET 2 LOAD
17 16
1SMB5939B MOSI ADDRESS DATA_OUT 2 R228
39V 5 6 7 +5V REFA 9 5
18 DACD 10.0K
C50 1 SCK I/O_CLK 3 7 J7
0.01 19 REFB U27:B 38 CARRIER REF (A)
2 3 14 EOC 4 R233 C140
1 VREF REF+
CR1 REFC 6 100 0.1 J7
t° U5 U8:A
BAT54HT1 4 U26 6 5 37
+5V VIN LT1790BIS6-2.5 VOUT REFD
9
COM
U30:H
GND
8 3 TMP36G 2 C147 C146
MC1413BD 12 0.1
GND1 GND2
10 R231 R232
A10 1 2 35V 10.0K 10.0K
R103 R102 R110
10.0K 10.0K 100
4
TP24 6 REFC
7 11 5 12 12
9 U34:H 8 REFD
COM GND U8:B A9 DACA
MC1413BD R109 20 14 J11 AUDIO
+24V 5
VCC +5V U28:D 1
R95 C55 100 C82 C81 U32 1 C158 C157 (SPEAKER)
R104 14 GND 13 R245 J11
68.1K 10.0K 0.1 U12 0.01 0.1 +5V VDD TLV5620ID 10 10.0K 0.1 2
L14 C155 C159 13
TLC1543IDW LDAC 35V
R120 TP33 0.1 0.01 R242
9 4750 R241 33.2K
9 U37:H 8 -15V 10.0K
COM GND 8 9 10
MC1413BD R134 R133 C66 R119 U8:C A8 GND R230
12.1K 1820 0.1 1210 R121 6 R229 15.0K
10 13 MOSI DATA 11 2
2 6 7 100 REF- DACB VO(LCD)
7 4750 1
SCK CLK U27:A TO SHEET 2
#SS5(DAC2)- +5V 3
8 R226
FROM SHEET 2 LOAD C141
4750 R227
TP30 13 1500 0.1
4 U3:E 11
+5V VDD GND 14 8
TLV2374ID U8:D A7
C34 SPEAKER_REF_LEVEL 2
+5V R111 FROM SHEET 4 REFA
0.1 12 13 14 R132 R118 C65 12 100 10 J11
22.1K 0.1 DACC 3 ANALOG METER
47.5K +5V R244 C152 J11
3920 0.1 4
4 U1:E 11 BAT_VOLT_SAMPLE RESET Q3
+5V VDD GND 7 FROM SHEET 1
TLV2374ID A6 MMBT4401LT1
C17 TP53
BAT_CUR_SAMPLE 6
0.1 A5 R239
12 13 14
RF_CURRENT_SAMPLE 2740
5 3
A4 REFB R237
9 5
FROM B+_SAMPLE 4 R240 DACD 10.0K
A3 7 J7
SHEET 4 3920 U28:B 40 CARRIER REF (B)
DC_CURRENT_SAMPLE 3 R236 C142
4 U2:E 11 A2 6
+5V VDD GND 100 0.1 J7
TLV2374ID PA_VOLTS_SAMPLE 2 39
C25 A1
0.1 48V_SAMPLE R235
1 R234 10.0K
A0
10.0K
3 U4:E 12
+15V VCC GND
C37 MC3302D
0.1
1 6 7
S1950142 SHEET 3 OF 4 V1
Dimensions = mm (inches)
TP17 C23 9
0.1 8 48V_SAMPLE
U1:C
J4 R41
+48V SAMPLE 29 10 TO
R87 C44 R43 R42 C22 100
J4 R86 SHEET 3
28 1000 10.0K 0.1 475K 475K 0.1
J7 TP25 2
28 POLARITY_ERROR
1
U7:A
J1 R108
# POLARITY ERROR - 23 3
R96 C51 100
J1 R97
24 1000 10.0K 0.1
J7
29
TP28 C52 6
0.1 7 PDM_A_SAMPLE
U7:B
J4 R98
PDM (A) 9 5
R142 C88 R105 R99 C53 100
J4 R143
8 10.0K 10.0K 0.1 475K 475K 0.1
TP29 C80 6
0.1 7 PDM_B_SAMPLE
U11:B
J4 R106
PDM (B) 7 5
R140 C87 R139 R138 C79 100
J4 R141
6 10.0K 10.0K 0.1 475K 475K 0.1
S1950142 SHEET 4 OF 4 V1
Dimensions = mm (inches)
Dimensions = mm (inches)
J10 J8
J11 J9 Fpdm (A) 10 18 Fpdm (A)
PDM1 (B) 24 20 PDM (B)
J11 J9
J9 Fpdm (B) 10 18 Fpdm (B)
21
J8
19
J3 J5 J9
7 PDM (B) 2FPDM (A) SYNTH 25 19
J3 E7:3
6
E7:1 BEACON
J16 J10
2FPDM (A) MISC 2 7 2FPDM (A)
KEYED TONE/AUDIO (A) 1
J15 J10
15 UNBALANCED AUDIO (A) DGPS E7:2 J10
6
R39 C15
68.1K 2200pF J6
2FPDM (B) SYNTH 25
E4:3
J15 J11
KEYED TONE/AUDIO (B) 19 15 UNBALANCED AUDIO (B) BEACON
R40 C21 E4:1
J15 J10 J4 J11
2 68.1K 2200pF 14 2FPDM (B) MISC 2 7 2FPDM (B)
J15 J11 DGPS E4:2 J11
20 14 6
TP4
J8 J10 J15
B+ REF (A) 12 3 B+ REF 1 (A) 37 SERIAL TO REMOTE
J8 R27 R28 R29 C19 R30 C20 J10 J15
13 82.5K 8250 3320 0.0022 3320 0.0022 4 B+ REF 2 (A) 38
TP3 J15
39
J9 J11 J15
B+ REF (B) 12 3 B+ REF 1 (B) 40
J9 R15 R16 R17 C13 R18 C14 J11
13 82.5K 8250 3320 0.0022 3320 0.0022 4 B+ REF 2 (B)
J7 J8
19 22 SERIAL TO PM BLOCKS
J10 J7 J7 J8
# PDM LATCH A + 11 6 # PDM LATCH A + 21 23
J11 J7 J7 J8
# PDM LATCH B + 11 7 # PDM LATCH B + 20 24
J7 J8
22 25
J7 J10 KEY CW KEY CW
# SHUTBACK A - 1 16 # INHIBIT PDM (A) -
E9 2 2 E8
CR22 DGPS BEACON
J13 J7 1 1 1 1 J10
3 CARRIER REF (A) 38 2 CARRIER REF (A)
2 3 3 2
CR2 E10:1 E10:2 E10:3 J7
37 KEY CW KEY CW
J7 J11 J13
# SHUTBACK B - 2 16 # INHIBIT PDM (B) - 20
CR21 DGPS BEACON J13
J13 18
23
CR1 E11:1 E11:2 E11:3
KEY CW KEY CW
E3 2 2 E2
J10 J7 1 1 1 1 J11
1 # RESET PDM (A) - CARRIER REF (B) 40 2 CARRIER REF (B)
CR8 2 3 3 2
J7 J11 J7
# RESET PDM - 18 1 # RESET PDM (B) - 39 KEY CW KEY CW
J13
CR3 40
J1 J3 J7 J13 J13
29 14 13 35 38
J1 J3 J3 J7 J13
AC SIGNAL (A) 30 21 AC POWER 16 16 15
J13
J3 J7 J13 17
J2 J3 18 29 13
AC SIGNAL (B) 29 20
J3 J7 J13 J13
J2 22 31 33 19
30
J1 J3 J13 J13
31 24 11 37
J1 J3 J13 J13
32 26 31 39
J2 J3 J5
31 28 1
J3 J15
J2 30 J5 9 KEY CW
32 14 2 E1
J3 J15
S1950009 SHEET 2 OF 2 V3 32 J5 11 1 1 J13
15 16
J3 J15 3 2
33 13 #KEY CW -
J13 KEY CW J13
4 J15 36
J3 J6 15
34 1
J13 J15
24 J3 27 J9
36 J6 1
J7 14
3 J3 J15 J9
38 J6 28 2
15 J15
J3 29 J9 POWER BLOCK ADDRESS
40 J15 3
30
J8 J9
8 4
J4 J8
1 9
J4 J16
3 1
J4 J9 J16
7 8 3
J9 J16
9 7
Dimensions = mm (inches)
J11 J18
RF CURRENT SAMPLE 17 7 RF CURRENT SAMPLE
J11 CR22 R19 R156 C56 R158 C57 J18
18 1000 10.0K 0.0047 10.0K 0.001 8
J18
3 FWD PWR SAMPLE
J17
1 FWD PWR SAMPLE
J11 J16
FWD PWR SAMPLE 1 1 FWD PWR SAMPLE
J11 R77 R78 C54 R48
2 6810 1820 0.001 0.0
6
7 1 T1 6
U1:B 21 (+)
5
C3
R55 R1 C1 10 2 7
8250 5620 0.0022 35V 22 SHIELD AUDIO
MONITOR
3 8
+15V 23 (-)
C2
0.0047
R32
22.1K
J17
PRESS-TO-TALK 12 3 # PTT (A) -
CR10 C23 R114
R38 0.1 CR9
A B 22.1K 10.0K J16
E4:1 E4:3 3 # PTT (B) -
GND 13
E4:2
J17
9 # MISC (A) -
J17
SHIELD 15 2
C17 R18 TP1 TP4 TP9 TP12 J16
U3:B 2
1.0 68.1K 10 7 4 14 U9:G 7
+15V V+ AD620R V- -15V +5V VCC GND J18
+15V 8 SN74AHCT14D 4
R17 U1:C C20 TRIM TRIM REF C16 C66
R27 10.0K 0.1 1 8 5 0.1 0.1
475 11 9 GND GND GND GND
9
CR11
R96 J17
(+) 14 1000 4 VOICE INPUT (A)
AUDIO R26 C21 R31 C22
R29 10.0K 10 150pF CR12 J17
INPUT 301 475K 5
35V
-15V
J16
4 VOICE INPUT (B)
+15V
TP2
3 J16
R28 5
301 CR3 6
U3:A
(-) 16 R34
R23 C13 C15 2 475 U21:B J18
R22 CR2 31 # MOD PROT/
10.0K 10 475K 150pF 2 15
35V AUDIO LIMIT -
J18
32
-15V
11 +15V
R87 +15V R98
C65 C73 9 1.82M J13
390pF 390pF 4750 32
17 6 8 13 10
U8:C R99
+5V 7 R93 R92 14
R84 R83 U8:B C71 R94 U8:D 1000 U10:D
U9:A 10 7 13
150K 150K R85 C64 R86 R89 R88 C72 0.047 1820 10.0K 10.0K
C69 J13
36
CW
Dimensions = mm (inches)
E10:2
12 AD603AR R54 3 6 NORM
J8 RF MONITOR E6:1 E6:2
2 Y0 3 R122 R113 C40 R53 U6:B
L U22:D 14
VINP AGC C104
0.1
R125
Q15 1000
R120 R112 C90
0.1 22.1 RF OFF / 4750
0.1 10.0K CR16 MOCD223-M
Y 15 E10:1 33.2K 1000 10 STANDBY CODE 2
13 R126 4 5
3320 Q10 (-) 8
1 Y1 7 7 2N4403
H VEE -5V VOUT
R124
C100 R121 J18
200 332 E7:3 E15:3 20 # RF ON +/OFF -
CW
0.1 6
-5V VNEG 5 MONITOR +24V-B
5 ZO Z 4 C111 FDBK
C99
NDB J18
L
0.1 LEVEL 16 # EXT RF ON -
0.1 (+) 5 E15:2 E15:1
C114 9 E7:1 E7:2 R71 1 8 NORM
3 Z1 0.1 8 1 RF ON / 4750 C44 R70 U7:A
+5V H U22:C GPOS 0.1 10.0K CR17 MOCD223-M
R148 C48 RF ON/OFF 2 7
R151 C117 10 10.0K 0.47 (-) 6
R161 475K 0.1
10.0K 2
J18 11 A GNEG
RF MONITOR SELECT 12 ENABLE
6 NORM
4 J18 E17:2
10 B 8 COMM # REMOTE COMMON - 9
GND E17:1
9 C NDB
E8:3 E17:3
+24V-B
J18 J18
MONITOR AMPLIFIER GAIN 11 17 # CHARGER ALARM -
(+) 3
R146 R76 3 6 J18
475K E8:1 E8:2 18
4750 C50 R75 U7:B
J12 J18 CHARGER ALARM 0.1 10.0K CR18 MOCD223-M
BATTERY CURRENT 22 25 BATTERY CURRENT
SAMPLE J12 R63 C42 J18 4 5
23 1000 0.47 26 (-) 4
24 GND
J12 J18
BATTERY VOLTAGE 24 27 BATTERY VOLTAGE
SAMPLE J12 R72 C47 J18
25 1000 0.47 28 19 +24V-B
R162
EXT INTLK 3920
J12 J18 U21:C J18
# DC INSTALLED - 7 40 # DC INSTALLED - 20 29 # EXT INTLK OPEN +
3 14
R15 C10 R16
3320 0.1 CR1
10.0K
J13
6
J12 J18 J13
# POLARITY ERROR - 8 23 # POLARITY ERROR - 34
J12
9
J12 J18
CHARGER CURRENT 10 33 CHARGER CURRENT
SAMPLE R12 C9
J12 1000 0.1 J18 J17
11 34 EXT RF IN / 24 MSK (A)
J6
MSK (A) J17
25
J12
1 +24V_BATTERY J16
J12 TO SHEET 3 MSK (B) 24 MSK (B)
+24V (BATTERY) 2 J7
J16
J12 J13 25
3 21 +24V (BATTERY)
J13
J12 22
4 J13
J13 RF OSC SAMPLE 3
J12 23
5 J13
J13 4
J12 24
6
J13
25
J11 J17
J13 RF VOLTS MONITOR 9 16 RF VOLTS MONITOR (A)
+5V 17 +5V J13
L2 26 J11 J16
C29 C30 C31 10 16 RF VOLTS MONITOR (B)
J13 10 0.1 0.01 J13
9 27
16V
J13 J13 J11 J17
11 28 RF CURRENT MONITOR 13 18 RF CURR MONITOR (A)
J13 J11 J16
29 14 18 RF CURR MONITOR (B)
J13 J13
8 30
J13 J17
+24V 10 +24V-A 17
L3 C36 C35 C39 J17
J13 J12 19
31 10 0.1 0.01 +15V 12 +15V
35V +24V-B J16
J13 L1 C26 J12 17
33 13
0.1 J16
19
J12
+24V-A 19
J13
+15V 12 +15V J12
L6 C52 14 +24V
J13 C55 C51
14 10 0.1 0.01 J12
35V 15
J13
13
J13 +15V-B
15
-15V
J13
-15V 16 -5V
L4 C46 C45 C41 C80 R152 C118 C119 C120
10 0.1 0.01 0.1 1000 10 0.1 0.01
35V 16V
R153
1000 CR21
1SMB5918B
S1950123 SHEET 2 OF 3 V2 5.1V
Dimensions = mm (inches)
+5V
3
DE VCC
8
+5V R139 R159 INTERNAL SERIAL INTERFACE 0.1
3 5 9 11 13
1
R138 C112 C113 121K 121K 1
2
10.0K RE 0.01 0.1 1
U19 R145 R160 4
+5V A2
DS36C278TM 121K 121K 1 C88 8
0.1 1 U13 VCC
6 J4 A1
1 DO/RI 1 TX HCPL-0731 R134
TP10 RO 2
7 J4 K1 1000
DO/RI 2 TX 6 4
J18 4 TP5 7
VO1 VO2 DI 8 J3
EXT TXD (TTL) 37 DI 5 VCC 1 +5V (ISOL)
GND 1 3 5 C108 C107
J18 8 RO K2 GND
38 J4 +5V VCC 0.1 10
5 R106 1 U17
C81 C82 R137
TP11 0.1 0.01 2210 DS36C278TM 121K 1 1
U11
EXT SERIAL BUS 6 J3
J18 1 8 DS36C278TM 8 1 DO/RI 3 INT BUS (+)
EXT RXD (TTL) 35 RO VCC +5V RS-422 +5V VCC A1
J18 C109 C106 J13 6 C89 4 7 J3
U18 U14 A2
36 0.01 0.1 INT BUS (+) 37 DO/RI 0.1 R109 R110 DO/RI 4 INT BUS (-) INT SERIAL BUS
DS36C278TM TP7 HCPL-0731 2 1
J13 7 1000 1000 K1 RO R136 J3 RS-485
INT BUS (-) 38 DO/RI 5 121K 2 GND (ISOL)
6 J4 4 7 R135 GND
4 DO/RI 7 RX DI VO1 2210 2 J3
DI RE
1 1 6 GND (ISOL)
R143 R142 J13 TP6 3 3
3 221 221 39 K2 DE J3
DE 7 J4 5 25 GND (ISOL)
DO/RI 8 RX J13 GND 3 U9:F 6 R133
2 40 DE VO2 2210 1
RE 5 12 13
GND 2 5
RE GND U15:A J3
2 1
5 DE/RE
C102 R33 R132
0.1 10.0K 1000
1
14 J5 1
12 T1OUT 3 TXD
R1OUT R130 J17
100 J5 6 (+)
11 5 GND
T1IN 16 J17
VCC +5V 7 (-) INT BUS (A)
2 C95 C94 J17
V+ 0.1 1.0 8
U12 C83 35V
ADM3202ARN 1.0
35V
13 J5 4 U1:E 11 3 U10:E 12 J16
10 R1IN 2 RXD +15V VCC VEE -15V +15V VCC GND 6 (+)
T2IN R131 C8 MC33074AD C12 C74 MC3302D
R123 6 100 0.1 0.1 0.1 J16
V- EXT SERIAL BUS 2 4 5 7 (-) INT BUS (B)
100 C79 RS-232
15 1 J16
GND C1+ 1.0 8
C84 35V
1.0 J5
8 35V 4 DTR
R2IN 3
C1-
R105 J5 4 U8:E 11 9 U21:H 8
100 4 6 DSR +15V VCC VEE -15V COM GND J10
C2+ MC33074AD CR20 MC1413BD 17 INT BUS (+)
9 C85 C60 C70
R2OUT 0.1 0.1 1SMB5939B
1.0 3 1 2 39V 1 4 5 6 7 J10
35V J5 18 INT BUS (-)
7 5 7 RTS
T2OUT C2- J10
J5 19
8 CTS
J10
20
J17 J16 4 U22:E 11
KEY MONITOR (A) 14 15 KEY MONITOR (A) +5V VCC VEE
C116 MC33074AD
J16 J17 0.1 J10
KEY MONITOR (B) 14 15 KEY MONITOR (B) 3 5 1 2 6 7 +5V 1 +5V
C77 L9
J17 J18 C76 J10
# KEYING/MISC ALM (A) - 10 21 #MISC A FAIL - 10 0.01 2
16V
J16 J18 TO
# KEYING/MISC ALM (B) - 10 22 #MISC B FAIL - DAUGHTER
J10
+15V 3 +15V BOARD
J17 J18 C68 L8
# MSK ALARM (A) - 11 13 # MSK ALARM (A) ? C67 J10
10 0.01 4
J16 J18 16V
# MSK ALARM (B) - 11 14 # MSK ALARM (B) ? NORM
E18:1 E18:2 J10
J17 J13 +24V-A 7
KEYED TONE/AUDIO (A) 12 1 KEYED TONE/AUDIO (A) C63 L7 +24V
+24V_BATTERY E18:3
BATTERY 10
C62 J10
8
J17 J13 0.01
13 2 FROM SHEET 2 16V J10
9
J16 J13 J10
KEYED TONE/AUDIO (B) 12 19 KEYED TONE/AUDIO (B) 10
J16 J13 J10
13 20 11
J10
12
J18 J12
# AC INHIBIT - 1 20 # AC ENABLE -
J18 J12
# DC INHIBIT - 2 21 # DC INHIBIT -
S1950123 SHEET 3 OF 3 V2
Dimensions = mm (inches)
+5V +5V
J2
1 MISO
R32 R7
4750 4750
11 11 +5V
+12V-A A 10 TP6 +12V-A A 10
R26 1 8 SA R1 1 8 SA
3920 C12 R27 U5:A 9 3920 C1 R2 U1:A
0.1 CR9 QH 0.1 CR1 R127
10.0K MOCD223-M 10.0K MOCD223-M 10.0K
2 7 7 2 7 7 3 U29 2 J2
MONITOR POINT 9 10 QH MONITOR POINT 1 1 QH +5V VCC ADM803MAKS RESET 5 RESET
C62 GND
+5V +5V 0.1
1 J2
+5V 2 VCC
L4 C66
R33 R8
4750 4750 0.1
12 12
+12V-A B +12V-A B J2
R30 3 6 R5 3 6 6 GND
3920 C14 R31 U5:B 3920 C3 R6 U1:B
0.1 CR11 0.1 CR3
10.0K MOCD223-M 10.0K MOCD223-M
4 5 4 5
MONITOR POINT 10 11 MONITOR POINT 2 2
+5V +5V
TP11 29
RESET 1
R36 R11 U27:C PD.3
9 16 12
4750 4750 QH
9 8
MISO PB.0
13 13
+12V-A C +12V-A C
10
R28 1 8 R3 1 8 25
PC.2
3920 C13 R29 U6:A 3920 C2 R4 U2:A 26
0.1 CR10 0.1 CR2 PC.3
10.0K MOCD223-M 10.0K MOCD223-M 14
+5V SS 27
2 7 2 7 PC.4
MONITOR POINT 11 13 MONITOR POINT 3 3 R123 28
10.0K PC.5
+5V U13 +5V U10 13
MC74HC165AD MC74HC165AD OC1A
S1950062 SHEET 1 OF 3 VA
DENOTES TB1
DENOTES TB2
14 7
+5V VCC GND
DENOTES TB3 C57 C56 4 5
0.1 0.01 U27:E
10 MC74HC125AD 9
DENOTES TB4 13 12
Dimensions = mm (inches)
SCK
FROM SHEET 1 SHIFT/LOAD
S1950062 SHEET 2 OF 3 VA
Dimensions = mm (inches)
R151
TP4 10K
1 +12V
C91
R25 1.0 2
10.0K
J1 7
+5V 1 +5V 3
L1 C8 C7 C11 9 U36:H 8
COM GND
J1 10 0.1 0.01 MC1413BD
2
35V
7
9 U32:H 8
COM GND
MC1413BD
J1
+15V 3
7
J1 9 U34:H 8
4 COM GND
MC1413BD
7
9 U30:H 8
COM GND
2 CR42 MC1413BD
6 TP3
OUTPUT MBR1645
J1 3 U39 2 4 U38 1 6 COMMON
+24V (BATTERY) 7 V_IN LM350T V_OUT Vin MC33167T FDBK
J1 ADJ R155 C93 C95 GND C R149
8 1 1000 0.47 10K 12
1 2.5W 50V 3 5 1
J1 14
9 1 +V +12V-A 18
VIN
J1 R150 10
10 C94 R154 R152 C92 C90 C89 C88 CR41 OV
0.022 15K R153 5620 1000 0.47 0.01 0.47 1N4744A 150 24
J1 3920 50V 15V 2W U37 11 C87 R148
11 +V
NDY1212 100 150
13 2W 6
J1 GND 25V
12 12
GND 24 12
VIN
15
OV 18
24
SCK
FROM SHEET 1 LATCH_CLK
S1950062 SHEET 3 OF 3 VA
Dimensions = mm (inches)
CW
P1 3 1000 R59 5
UNBALANCED AUDIO 15 12 1000 10
C19 R16
P1 R4 470pF 681K DUMP
14 681K 1.4 V dc 1 5
X1 -VS -15V-A
U6 C37 C39 L6 +15V-B
2 0.1 10 +15V-B
X2 AD633AN
4
35V INTERPHASE PDM
Y2
6 8 GENERATOR (1) C56
10
C60
0.1
Z +VS +15V-A R60 R62 Q4 TP17
1 U4 3 C38 C20 L7 R52 9 35V
V_IN MC7805ACT V_OUT +5V 1210 1000 2N4401
0.1 10 7 3 2
C5 C7 GND C13 L3 C3 C11 35V 1000 U10:B K1:A
0.22 0.1 0.1 10 0.1 R74 4 P1
2 Q5 24 PDM 1
35V 3 7 R53 10 R65 10
Y1 W C48 C50 2N4403 56.2K
R12 C71 562 R77 P1
0.001 100pF +15V-B 1000 25
P1 10K 0.1
+15V 18 +15V-A CR3
L1 C1 C9 C15 R15
10 10 0.1
35V 35V
2740
Q2 +15V-B
R70
10K
PDM FAULT
5 TP12 R54 C52
2N4401 DETECTOR
-VS 5
+15V-B 1000 0.001 R67
L2 C2 C10 C16 U7 8 2
P1 +VS 1.0M U12:A
19 10 10 0.1 2 AD633AN
35V 35V
+
B Sample = B
+
÷ 54.9 4
X2
Y2 W
7 R44
10K C58
4
R13 TP9 0.01
P1 TP4 – A6 – A 6
Z 10K 2 2 0.1%
-15V 12 -15V-A CW GAIN
L4 C4 C12 C17 A10 – B Y1
3
U13:A R38 U3:A
1
10 10 0.1 1
R27 R31
TRIM 10K +15V-B 15V PDM modulated
P1 35V 35V 3 18.2K 5000 0.1% 3 TP13 +15V-B
+5V 17 TP8 INTERPHASE PDM square wave at approx.
6
7 GENERATOR (2) C57 C61 130 kHz
TP4 R2 U3:B R49 10 0.1
22.1K R61 R63 Q6 TP18
13 R39 R42 10K R50 9 35V
5 10K 1210 1000 2N4401
14 1 10K 9 0.1% 7 8 9
U3:D X1 0.1% 0.1% 562 U11:B K1:B
P1 8 7 P1
B+ SAMPLE 3 R46 U3:C R75 22 PDM 2
R1 C6 12
CARRIER 10K R51 10 Q7
2N4403
R66 10
100K 470pF C49 C51 56.2K
LEVEL 0.1% 10 1000 100pF 0.001
R78
1000
P1
23
0 to 6 Vdc depending on CONTROL R47
4990 CR4
TP5 power level
TP1 2 Q3 +15V-B
TP14 2N4401
1 TP5 – A6 – A R55 C53
U2:A
P1 1000 0.001 7
CARRIER REF 2 3 A10 – B R68
R3 C8 1
1.0M U12:B
P1 10K 0.47
13 6
CR1 Anode Low C59
0.01
Power Inhibited +5V E1:3
Q1
2N4401 E1:1 B
R48 C45
R7 10K 0.001 E1:2
100K
A
1
P1 12 R71 R72 +5V
# INHIBIT PDM - 16 11 10K 10K
CR1 R6 U9:D CR5 K1:C
1000 +5V 13
10
R36 P1
100K 11 # PDM
P1 1 LATCH +
# RESET PDM - 1 3 Q10
R33 U9:A 2N4401
1000 +5V 2 R69 C63
1000 0.001
R37 SHUTBACK
4
1000
U9:B
6 LATCH TP11
14 U1:C 7 4 U8:E 11 5
+5V VCC GND +15V-A VCC VEE -15V-A
C18 C21 MC74HC74 C34 MC34074 C42
10 0.1 0.1 0.1
35V 10 11 12 13 12 13 14
6 6 6
-V -15V-A -V -15V-A -V -15V-A
11 U5:C 3 C46 C47 11 U10:C 3 C55 11 U11:C 3 C66
13 14 +15V-A +V GND-A
0.1 10 +15V-B +V GND-A
0.1 +15V-B +V GND-A
0.1
C43 C44 LM319J 8 C54 LM319J 8 C62 LM319J 8
GND-B 35V GND-B GND-B
4 U13:E 11 4 U2:E 11 14 U9:E 7 10 0.1 0.1 0.1
+15V-A VCC VEE -15V-A +15V-A VCC VEE -15V-A +5V VCC GND 35V 7 9 10 4 5 12 4 5 12
C24 MC34074 C30 C22 MC34074 C28 C35 MC74HC00
0.1 0.1 0.1 0.1 0.1
5 10 12 6 7 8 9 9 10
4 U3:E 11 3 U12:E 12
+15V-A VCC VEE -15V-A +15V-B VCC GND
C23 MC34074 C29 C36 MC3302
S1970043 SHEET 1 OF 1 V3
0.1 0.1 0.1
10 11 13
Dimensions = mm (inches)
J1 J2
17 37 +24V RETURN
J1 J2
18 38
J1 J2
19 39
J1 J2
ALTERNATE +15V 20 40
J1
13
J1 -15.8V
14 L1
6 7 J2
J1 12 -15V
15
CR7 CR6 C2 C10 C11 R21 J2
J1 2 MBR1645 MUR120 1000 0.47 0.01 1000 11
16
OUTPUT 50V 0.5W
4 Q1 1 1 13
J1 Vin MC33167TV FDBK
ALTERNATE -15V 12 C24 J2
GND C 17
J1 0.47
11 3 5 J2
+15.8V 18
J2
19 +15V
C4 R4 R2 R1 C3 C12 C13 C14 C20 CR17 R27 R30 R31 J2
0.1 68.1K 1000 6810 1000 1000 0.47 0.01 0.47 RT3 1N4746A 150 150 150 20
CR1 50V 50V 18V
MUR1520 RXE250 2W 2W 2W J2
R3 13
+24.8V 2210 J2
J3 14
+24.8V 1
C1 J2
J3 15
2 RT1 1000
50V J2
RXE250 16
J3
3
J3 -5.8V
4 6 L2 7 J2
2 -5V
CR11 CR10 C7 C15 C16 R28 J2
MBR1645 1000 0.47 0.01 1
J1 2 MUR120 1000
+24.8V RETURN 3 OUTPUT 50V 0.5W
4 Q2 1 1 13
J1 Vin MC33167TV FDBK
4 J2
C8 GND C 7
J1
5 0.47 3 5 J2
+5.8V 8
J1
6 J2
9 +5V
C6 R8 R10 R7 C9 C17 C18 C19 C21 C22 C23 CR12 R29 J2
J1 68.1K
7 0.1 27.4K 6810 1000 1000 0.47 0.01 0.47 0.47 0.47 RT4 1N5920C 1000 10
50V 50V RXE110 6.2V 0.5W J2
J1 R9 3
8
18.2K J2
J1 4
9
J1 J2
ALTERNATE +5V 10 5
J1 J2
ALTERNATE -5V 2 6
J1
1
J1 J2
# LVPS FAIL (B) - 25 21 # LVPS FAIL (B) -
J1 J2
26 22
J1
27
J1
28
J2
23
J2
J1 24
ALTERNATE AC SIGNAL 29
J1 4 T1 5
30 J2
29 AC SIGNAL
J1 CR8 C5 R5 R6 R11 CR18 C26 J2
31 100 22.1K 10 30
2210 15K
J1 25V 35V J2
32 +9.4V 31
3 6
2 7 J2
E1 +9.4V 32
2 R23
4750
170-270VAC R25 R22 1 J2
R18 U1:A 25 # LVPS FAIL (A) -
E2 5600 CR15 12.1K 1 5
1N5992D 2210 CR13 J2
1 8 0.5W 3
U2 26
4.7V +9.4V MOC8104 8 U1:C 4 J2
CR16 +9.4V VCC GND 27
2 4
C25 LM393N
1N5992D J2
4.7V 5 R24 0.1 28
4750
7
U1:B
+24.8V 6
CR14
R12 R17 R19
39.2K CR9
10K 3320
+5.8V
R13 R20
12.1K 332
+15.8V
R14
39.2K
-5.8V
R15
18.2K
-15.8V
S1950050 SHEET 1 OF 1 VB R16
39.2K
Dimensions = mm (inches)
+5V
E3:3
R67
A B
E1:1 E1:2 A J1
U13 10.0K 14 KEYING MONITOR OUTPUT
3 2
+5V VCC ADM803MAKSRESET RESET CR4 E3:1 E3:2
C53 GND BAT54HT1
B
0.01 MOSI E1:3
1 2
+5V VCC 7 +5V
SCK RESET KEYING_GATE_CTRL
C9
0.01 CR6
J2 17 U2 3 BAT54HT1 R50
GND
SCK 3 SCK ADM705AR 10.0K U15:A
23 6 4 6 J1
PC.0 WDI PFI QG 10 KEYING/# MISC ALARM +
J2 15 1 2
MOSI 4 MOSI CR5
R13 5 U16 BAT54HT1
PFO 9 U15:B
J2 29 475 SQH MC74HC595AD 5 J4
RESET 5 RESET 1 8 QF
3 4
5 # CHANGEOVER -
MR WDO 10 R51
J2 16 G DS1 RESET RESET 10.0K
MISO 1 MISO U15:C
KEYER OK 14 4 J4
MOSI A QE 6 # SHUTDOWN -
J2 R52 5 6
VCC 2 +5V 11
SCK SHIFT_CLK 10.0K
J2 4 U7 6 20 U15:D RF_OFF
GND 6 +5V VIN LT1790BIS6-4.096 VOUT AREF 14 12 7
SS/PB.2 LATCH_CLK QH
C26 GND1 GND2 C25 C24 9 8
0.1 1.0 0.1 2 MOD_SELECT
1 2 35V QC TO SHEET 2
15 #KEYED_CW+
QA
16
+5V VCC
U11 C65
0.01
INTERNAL TP2 TP3 ATmega168-20AI
3 MOD ENABLE 10 B
QD
SERIAL INTERFACE 8
GND VCC
16
+5V
1 PTT 11 A C17 C16
R27 R28 13 QB
OE 0.01 0.1
8 10.0K 10.0K
+5V VCC 1 30
C38 C43 RO RXD
U12
0.1 0.01 4 31
DS36C278TM DI TXD 9 9 C 7
PD.5 VEE -5V
2 26 C1
RE PC.3
TX/RX 6
J1 6
DO/RI 3 TONE GENERATOR 0.1
DE 6
J1 7 MOSI SDATA 1
TX/RX 7 DO/RI 5 COMP +5V
GND 7 6
J1 SCK SCLK C5 ENABLE
8 0.01 8
25 8 GND
PC.2 FSYNC 3
CAP/2.5V TP4
2 C13
+5V VDD
C7 C6 U5 0.1
10 0.1 AD9833BRM 5 ZO TP1
16V 9 R16 L
4 AGND
+5V VCC 4 33.2K Z 4
+5V +5V +5V C51 C50 6 R25 DGND 10 9
VCC VOUT
0.01 0.01 1.00M 3 Z1
U4:E 5 C4 R2 U8:C H
R66 R43 R58 MCLK 10 10.0K 8
10.0K 10.0K 10.0K 11 10 10
J1 11 R64 R15
# PTT + 3 PD.7 2210 22.1K
R46
J4 100 1 C46 C57
# KEYED CW + 16 INT1
18pF Y1 18pF +5V
R65 3.6864MHz 10
100 +5V VLOGIC
J1 2 C35 C34 15
# MISC A - 9 PD.4 SHDN W1 3 12 XO R48
R42 0.1 0.01 L
100
100 7 1 B1 CW A1 2 R19
J1 32 XTAL1 X 14
KEYING MONITOR I/P 15 INT0 100K
R57 C40 C52 C37 C42 20K C76
W3 6 13 X1 10
100 0.1 0.1 0.1 0.1 H R29 TP5
4 B3 CW A3 5 R44 12 68.1K
100K 14 J1
18 R47 20K U8:D 12 KEYED TONE/AUDIO (A)
+5V AVCC 5620 W2 22
2 Y0 Y 15 C18
C28 C27 24 B2 CW A2 23 R56 L 13
1.0 R17 J1
0.01 0.01 27.4K 13
100K 35V
20K R37
10 13 9 R49
PD.6 CS/AD0 U10 DIS 1 Y1 18.2K 56.2K
H
AD5263BRU20 GND 8
14
C47 13 RESET RES/AD1
0.1 14 24 11 U1
U9:D PC.1 MOSI SDI/SDA 7 MC74HC4053AD
J1 3 VDD +5V
FORWARD POWER 1 R54 GND 12 C33
R26 R62 C48 12 100
5
SCK CLK/SCL 0.1
J1 475K 475K 0.1 GND
2
21 19 W4
GND +5V
21 B4 CW A4 20 MSK_REF
TO SHEET 2
20K
16
SDO/O1
C30 2 18
17 VSS -5V
0.1 1 19 NC/O2 C41
RF_MONITOR U9:A ADC6
0.1
FROM SHEET 2 R45 R22
3 100
R30 R31 C31 3.32M
182K 182K 0.1 6
27 R86
PC.4
7
U8:B
C82 C80 CR11 562K
R84 5 J3
0.1 0.47 100K BAT54HT1 1
9 J3
8 22 4
U9:C ADC7 R23
R55 C84 R41 J3
10
CR7 C49 R60 3.32M U17:A 7
BAT54HT1 10 332K 0.0 10 100 2
1 2
28 R87
PC.5 U8:A
C83 C81 1 562K U17:B J3
R85 CR12 3 2 2Fpdm
0.1 0.47 100K BAT54HT1 3 4
DGPS_CARRIER_FAULT 12 U4:A U17:C J3
FROM SHEET 2 ICP/PB.0 13 3
OC1A
1 2 5 6
J1
VOICE I/P 4
J1 R76 C85 R81
5 22.1K 10 22.1K
S1950129 SHEET 1 OF 2 V2
Dimensions = mm (inches)
E2:3
J4
681 4
14 U15:G 7
+5V VCC GND #KEYED_CW+
C39 MM74AHCU04M
0.1 CR8
RF_OFF BAT54HT1
FROM SHEET 1
CR13
14 U4:G 7 MSK_REF BAT54HT1
+5V VCC GND +5V
C23 MM74AHCU04M R5
R7 R6
0.1 1000 1000 12.1K
5 R18
1000 U15:F
2 J1
U6:A 11 # MSK ALARM -
R53 13 12
CR3
4 10.0K
C55 R68 CR2 R20 C10 BAT54HT1
3 U6:E 12 J4 0.001 10.0K BAT54HT1 10.0K 0.001
+5V VCC GND # SYNTH INSTALLED - 1
C8 MC3302D
0.1
5 V RF drive
+5V
square wave U20:B
14 U18:G 7 +5V 3 4
+5V VCC GND R8
C74 SN74AHCT14D
825 U18:A U18:B U20:D U20:A
0.1 R9 J3
1 2 3 4 9 8 1 2
5 RF DRIVE OUTPUT
3920 C78 C60 R72
J1 Q1 R71 J3
EXT Fc 24 MMBT4401LT1 0.001 0.01 0.0 U20:C 6
10.0K +5V
C15 R14 R73
J1 R11 R12 0.01 5 6
25 100 100 1000 R1 10.0K
56.2 R10
14 U20:G 7 TP6 C61 R74 8250
+5V VCC GND 100K 7
C72 CD74ACT04M 0.01 2
J4 C11 1
0.1 +5V 10 +5V 1 U6:B
L1 U19:A R75 C54 0.01
J4
C64
10
C58
0.01
MSK 50/50 100K 10
R21
1000 6
11
16V GENERATOR 3
TP9 9 CR1
14 U17:G 7 +5V
+5V VCC GND R82 C75 C79 R32 C14 14 BAT54HT1
CD74ACT04M U6:C
C63 J4 1.00M R83 0.1 10 100K 0.1 DGPS_CARRIER_FAULT
0.1 +15V 12 +15V 1.00M 8 TO SHEET 1
L2 C56 C59 R36
J4 10 0.01
GND 8250
13
35V
4 U19:E 11 TP8
+5V VDD GND -15V
C62 TLV2374ID
0.1 J4
-15V 14 -5V
L3 C67 C66 R78 CR10 C73 C68
J4 10 0.01 1000 1SMB5918B 10 0.1
15
35V 5.1V 35V
R77
S1950129 SHEET 2 OF 2 V2 1000
Dimensions = mm (inches)
E11
E10
E13
E12
6
E9
E8
E7
E6
E5
E4
E3
E2
E1
PWB
XA1A1P1 E20
Fc (A) 1 J1 W2P2 W2P1 RF OUT
E19 C4 C8 C14 C13 C11 C9 C12 C10 C16 C15
SHIELD 2 0.0036 0.0036 0.0036 0.0036 0.0036 0.0036 0.0036 0.0036 0.0036 0.0036
N/C 3 E18
E31 E34
GND 4 C3 C7
0.0036 0.0036
PA VOLTS SAMPLE (A) 5
SHIELD 6 E33 E36
E17
B+ SAMPLE (A) 7
E16 C2 C6
SHIELD 8 0.0036 0.0036
SHIELD 9
A1
E30
RF
N/C 10 POWER E32 E35 E29
PDM (A) 11 MODULE E15 E28
GND 12 A E14 C1 C5 E27
# PM INSTALLED (A) - 13 0.0036 0.0036 E21 E26
# RELAY CONTROL B - 1 INT BUS (+) 14 E25
GND 2 INT BUS (-) 15 E24
# INHIBIT PDM (A) - 3 A1P1
INT BUS (GND) 16 E23
# INHIBIT PDM (B) - 4 N/C 17 E22
+24V (A) 6 BLOCK ADDRESS 0 18
+24V (A) 7 BLOCK ADDRESS 1 19
GND 8 N/C 20
GND 9 BLOCK ADDRESS 2 21
Fc (A) 10 MODULE ADDRESS 0 22 1 # RELAY CONTROL B -
J4
SHIELD 11 N/C 23 2 GND
DUMP (A) 14 MODULE ADDRESS 1 24 Frequency E20 E21 E33 E36 E15 E17 3 # INHIBIT PDM (A) -
SHIELD 15 GND 25 4 # INHIBIT PDM (B) -
(kHz) to to to to to to
PDM (A) 20 DUMP (A) 26 6 +24V (A)
XA1P1
SHIELD 21 SHIELD 27 12 190.0 -209.0 E1 E22 E31 E34 E16 E18 7 +24V (A)
INT BUS (+) 22 GND 28 P1 8 GND
209.1 - 229.9 E2 E23 E31 E34 E16 E18
INT BUS (-) 23 +24V (A) 29 11 9 GND
GND 24 230.0 - 252.9 E4 E25 E31 E34 E16 E18
# INHIBIT PDM (A) - 30 10 Fc (A)
GND 25 253.0 - 278.2 E3 E24 E31 E35 E14 E18 J6
11 SHIELD
(PART OF) B
E3 # RELAY CONTROL B - 278.3 - 306.0 E5 E26 E31 E35 E14 E18 14 DUMP (A)
BLOCK ADDRESS 0 1
A4 K1 306.1 - 336.6 E6 E27 E31 E35 E14 E18 15 SHIELD
BLOCK ADDRESS 1 2 POWER BLOCK E2 +24V (PART OF) 20 PDM (A)
BLOCK ADDRESS 2 3 DISTRIBUTION A 336.7 -370.3 E7 E28 E31 E35 E14 E18
+24V (B) 6 PWB XA2A1P1
A6 21 SHIELD
Fc (B) 1 XA2P1 RF TRANSFORMER 370.4 - 407.3 E6 E27 E32 E35 E14 E16 22 INT BUS (+)
+24V (B) 7 PWB
SHIELD 2 12 4 407.4 -447.9 E7 E28 E32 E35 E14 E16 23 INT BUS (-)
GND 8 E1 20 T1 11 E5 (PART OF)
N/C 3 P1 1 7 24 GND
GND 9 448.0 - 492.9 E8 E29 E32 E35 E14 E16
GND 4
A4 25 GND
Fc (B) 10 11 6 E2 E6 493.0 - 535.0 E9 E30 E32 E35 E14 E16 POWER BLOCK
SHIELD 11 J5 PA VOLTS SAMPLE (B) 5 9 DISTRIBUTION
3 1 10 1 BLOCK ADDRESS 1
DUMP (B) 14 SHIELD 6 With 1 RF power block installed, connect E12 to E11 PWB
2 BLOCK ADDRESS 2
SHIELD 15 B+ SAMPLE (B) 7 With 2 or more RF power blocks installed, connect E12 to E10
3 GND
PDM (B) 20 SHIELD 8
6 +24V (B)
SHIELD 21 SHIELD 9
7 +24V (B)
+24V (BAT) 22 N/C 10
8 GND
+24V (BAT) 23 PDM (B) 11
9 GND
GND 24 GND 12
10 Fc (B)
GND 25 # PM INSTALLED (B) - 13
J7 11 SHIELD
INT BUS (+) 14
14 DUMP (B)
B+ SAMPLE (A) 12 INT BUS (-) 15
A1P1 15 SHIELD
SHIELD 13 INT BUS (GND) 16
J6 20 PDM (B)
PA VOLTS SAMPLE (A) 16 N/C 17
SHIELD 17 BLOCK ADDRESS 0 18
A2 21 SHIELD
RF 22 +24V (BAT)
BLOCK ADDRESS 1 19 POWER
B+ SAMPLE (B) 12 23 +24V (BAT)
N/C 20 MODULE
SHIELD 13 * DENOTES INSTALLED IN DUAL XMTR 24 GND
J7 BLOCK ADDRESS 2 21 B
PA VOLTS SAMPLE (B) 16 25 GND
MODULE ADDRESS 0 22 *
SHIELD 17 N/C 23 12 B+ SAMPLE (A)
MODULE ADDRESS 1 24 13 SHIELD
GND 25 J4
16 PA VOLTS SAMPLE (A)
DUMP (B) 26 17 SHIELD
SHIELD 27
GND 28 12 B+ SAMPLE (B)
+24V (B) 29 13 SHIELD
J5
# INHIBIT PDM (B) - 30 16 PA VOLTS SAMPLE (B)
17 SHIELD
XA2P1 BATTERY A (+)
P8
1
AC VOLTS (B) 3
2
P1
GND 25
W2P1 W2P2 J1 U1:A
DUMP 26 3 Fc 3 1 5
R1 C3 R2 YELLOW
SHIELD 27 2 2 2.5
47.5 0.47 2T Q3
15W STW14NM50 CR3
GND 28 MUR460
GREEN
+24V 29 1 1 3T
J4
# INHIBIT PDM - 30 4 4 E3
11 RF (2)
2 Q4
3 U1:B GND
9 +15V 9 Vs 4 STW14NM50 CR4
C1 MIC4452CT GND MUR460
F1 BLUE
10 10 1A 1.0 3T
SLOW
S1950011 VG
Dimensions = mm (inches)
J4
3 Fc - TO PA
P1 J4
4 2
TP5
P1 J2
26 9
DUMP DUMP
P1 J2
27 10
TP6
P1 J2
11 7
PDM PDM
P1 J2
9 8
S1950018 SHEET 1 OF 1 VC
Dimensions = mm (inches)
R4 R33
10K 10K
J1
OUTPUT ADJUST 2 11
1 5
+18V +18V U4
MOC8104
2 4
R56 R40
10K 10K
J1 R32
OUTPUT ADJUST 1 9 CR3
1 5 10K
U6
MOC8104
2 4
CR5 R37
10K
4 U5:E 11
+18V VCC
MC34074
VEE S F J2
C14 C16 1 DC OUTPUT
L6
0.01 0.001 R13 R16 R19 300μH C27 R43
390 390 390 5 33K
2W 2W 2W C45 600V 5W
12 J2
3.3 3
C11 CR13 C20
0.01 v 21T CR9
HFA08TB120 HFA08TB120 220pF
1 R9
J3 RV1 CR7 5 1.0M
1 U2 0.5W
SIOV-S14K300 DSP25-16A HFA08TB120
2 3 2
C4 v T1 S F R29 R5
AC INPUT 0.015 L3 R10 R24 R26 681 3.32M
L5
580uH R14 R17 R20 300μH 22.1K 22.1K 15K
RV2 1 R7 R1 C12 C13 C15 390 390 390
1 4 C17 1 R25 R27
SIOV-S14K300 3 100K 100K 470 470 470 5 2W 2W 2W C44 C35 C31
J3 450V 450V 450V 14 Q4 4750 1820 100pF
2 2W 2W 600V 3.3 MPF960 2700pF
v 2 U1 5T CR10 CR14 C21 C5
A B DSP25-16A 21T HFA08TB120 220pF 2
J3 A DS1 HFA08TB120 0.1 VFB 1
3 C9 AC COMP
RV3 20 C28
0.01 SIOV-S14K300 IND 7
3 19 Q5 0.01
MPF960
6T S F C6 U8
J1 L4 0.1 7
14 R15 R18 R21 +18V VCC UC1844AJ
+18V 300μH
2 390 390 390 C29 C30
T2 Q1 2W 2W 2W C43 1.0 0.01
4 3 16
CR1 IXFK44N60 3.3
1N5819 CR11 CR15 C23
4 3 6T 21T 3
+18V VCC OUT 10 HFA08TB120 HFA08TB120 220pF CUR_SEN
C2 5 C10 R57 CR20 CR4 C19 8
1.0 V_IN U3 3.3 HFA08TB120 P6KE20CA 3 18 9 R50 470pF VREF
CR2 1.0 Q2
J1 6 UC3710 1N5819 0.5W 20V 7 0.2 C32 R30
10 N/C IXFK44N60 3W 0.47 6810
R58 1 5
15 GND
8 1 3 T3 1 R35
N_INV INV 0.5W
332
2 8 CR6 CR12 R12 C37 R22 R23 R63 R64 4
P_GND HFA08TB120 1T 200T 0.001 68.1 392
7 1N5819 332 39.2 681 RT/CT
OUTPUT
6
L_GND C26
+18V +18V 4 2 1000pF
R61
5620
J1
# INHIBIT + 7
1 5 Q8
U7 2N7000
MOC8104 CR19 C36
CR18 R69
2 4 1N5819 1N5930C 0.01 1000
R52 C41 R28 16V
39.2 0.47 2210
+18V
R62
10K Q7
IRF520 C8
2.2
1 5 C18
U9 1.0 R41 R47
MOC8104 35V 10K 825
13
2 4
E2 R46 C24 14 J1
U5:D 19 DC CURRENT SIGNAL
182 0.01 C22 R51
E2 R3 R49 12 J1
FAN - OUTPUT OUTPUT 1000 1000 0.001 10 17
C7 10
0.1 ADJUST 1 ADJUST 2 5
E1 7 8
FAN + CR16 150V 0 0 U5:B U5:C
E1 1N5819 250V 1 0 9
6 +18V
R44 R65 CR17
350V 1 1 R39 1000 C33 1
J1 3 U10 2 1000 1000 1N4733A 0.1
21-24V INPUT 3 V_IN LM350T V_OUT +18V INVALID 0 1 5.1V 2 3
L1 C1 C25 J1
J1 ADJ
t° U11 C38 U5:A 12 TEMPERATURE
4 0.001 RT1 0.1 0.001 1
1
3 TMP36G C34 R68
J1 RXE050 2 0.001 10
1
J1 R55 R2 R67
2 R53 121
10K R66 10K
1500 10K
R54 G DS2
100 +18V
* E3 NOT INSTALLED ON NAPS31A/01 VERSION.
E3 J1
FAN FAIL 20 FAN FAIL
CR21
1N5819 S1970074 SHEET 1 OF 1 V3
Dimensions = mm (inches)
CR1
1N4004
J4 J6 J5 J7
+24V (A) 6 6 +24V (A) +24V (B) 6 6 +24V (B) J5 J7
+24V (BAT) 22 22 +24V (BAT)
J4 J6 J5 J7 J5 J7
7 7 7 7 23 23
J4 XA1A1P1 J5 XA2A1P1 J5
8 29 8 29 24
J4 J6 J5 J7 J5
9 8 9 8 25
J6 J7
9 9
XA1A1P1 XA2A1P1 J7
28 28 24
J7
25
J4 J6 J4 J6
# INHIBIT PDM (A) - 3 3 # INHIBIT PDM (A) - # INHIBIT PDM (B) - 4 4 # INHIBIT PDM (B) -
R3 XA1A1P1 R1 XA2A1P1 XA2A1P1
10K Q2 30 # INHIBIT PDM (A) - 10K Q1 30 # INHIBIT PDM (B) - 25
XA1A1P1 2N7000 XA2A1P1 2N7000 XA1A1P1
# PM INSTALLED (A) - 13 # PM INSTALLED (B) - 13 25
R4 C2 R2 C1
4750 0.001 4750 0.001
J4 XA1A1P1
INT BUS (+) 22 14 INT BUS (+)
J5 J7 J4 XA1A1P1
Fc (B) 10 10 Fc (B) INT BUS (-) 23 15 INT BUS (-) MODULE A
XA2A1P1 XA1A1P1
1 INT BUS (GND) 24 J4 16 INT BUS (GND)
J4 J6 J5 J7
Fc (A) 10 10 Fc (A) 11 11 J4
25
XA1A1P1 XA2A1P1 XA2A1P1
1 2 14 INT BUS (+)
J4 J6 XA2A1P1
11 11 15 INT BUS (-) MODULE B
XA1A1P1 J7 J5 XA2A1P1
2 B+ SAMPLE (B) 12 12 B+ SAMPLE (B) 16 INT BUS (GND)
XA2A1P1
7
J6 J4 J7 J5 J6
B+ SAMPLE (A) 12 12 B+ SAMPLE (A) 13 13 22 INT BUS (+)
XA1A1P1 XA2A1P1 J6
7 8 23 INT BUS (-)
J6 J4 J6
13 13 24 INT BUS (GND)
XA1A1P1 J5 J7 J6
8 DUMP (B) 14 14 DUMP (B) 25
XA2A1P1
26
J4 J6 J5 J7
DUMP (A) 14 14 DUMP (A) 15 15
XA1A1P1 XA2A1P1 J5 XA1A1P1
26 27 BLOCK ADDRESS 0 1 18 BLOCK ADDRESS 0
J4 J6 J5 XA1A1P1
15 15 BLOCK ADDRESS 1 2 19 BLOCK ADDRESS 1
XA1A1P1 J7 J5 J5 XA1A1P1
27 PA VOLTS SAMPLE (B) 16 16 PA VOLTS SAMPLE (B) BLOCK ADDRESS 2 3 21 BLOCK ADDRESS 2 MODULE A
XA2A1P1
5 XA1A1P1
22 MODULE ADDRESS 0
J6 J4 J7 J5
PA VOLTS SAMPLE (A) 16 16 PA VOLTS SAMPLE (A) 17 17 XA1A1P1
24 MODULE ADDRESS 1
XA1A1P1 XA2A1P1
5 6
J6 J4 XA2A1P1
17 17 18 BLOCK ADDRESS 0
XA1A1P1 J5 J7 XA2A1P1
6 PDM (B) 20 20 PDM (B) 19 BLOCK ADDRESS 1
XA2A1P1 XA2A1P1
11 21 BLOCK ADDRESS 2 MODULE B
J4 J6 J5 J7
PDM (A) 20 20 PDM (A) 21 21 XA2A1P1
22 MODULE ADDRESS 0
XA1A1P1 XA2A1P1
11 9 XA2A1P1
24 MODULE ADDRESS 1
J4 J6
21 21 XA2A1P1
4
XA1A1P1 J7
9 XA2A1P1 1 BLOCK ADDRESS 1
12
J7
XA1A1P1 2 BLOCK ADDRESS 2
4 J7
3
XA1A1P1 J4 E3 J7
12 # RELAY CONTROL B- 1 # RELAY CONTROL B- 4
J4 J6
2 1
J6
S1950027 SHEET 1 OF 1 VD 2
Dimensions = mm (inches)
E3 E4
3 U1 1 J1
+ LA 55-P M 10
- CR3 CR4
1N4004 1N4004 R2
2 100
J1 J1
12 11
L1 C2 C1
10 0.1
J1 35V J1 J1
13 7 1 (+)
F1 BATTERY VOLTS
12A RT1 4 (-) (EXCITER)
1 3 E1 E5 K1:A
BATTERY + 1 U1 P1 P2
F4 U2 1 2
3 1 J1 1 2 1 3
20A + LA 55-P M 22
LINE LOAD CR1 CR2
- R1 2
2 1N4004 1N4004
100 J3 J2
J1
U2 23
20VP6 J2
J1 3 1 1 (+)
24 BATTERY BOOST VOLTS
R4 CR5 7 F2
68K 1N4745A R3 A2 12A RT2 4 (-) (POWER MODULE)
2W 16V 1820 BATTERY BOOST
2 4 E2 J1 K1:B
BATTERY - 2 25 PWB ASSY
8
J1 E14
14 3
5 +
CR7
R6 1N4004 B1 E1
6 10K E15 -
4
Q2
J1 IRF530N
21
R5
10K ITEMS IN THIS AREA ARE INSTALLED FOR
J1
15 VR1000/VRD1500 ONLY
P3 P4
1 3
J2 J3
2 J3 1 1 (+)
F3 BATTERY BOOST VOLTS
3 12A RT3 4 (-) (POWER MODULE)
A3
+ BATTERY BOOST
PWB ASSY
B2 E1
S1950116 VD -
Dimensions = mm (inches)
J3 3 U10 2
21-24V INPUT 3 V_IN LM350T V_OUT +18V 13
L1 C1 C25 ADJ J2
0.001 RT1 0.1 T4 21T 1 DC OUTPUT
1 L2
RXE050 R13 R16 R19 R43
1mH C27
8 390 390 390 5 33K
R55 R2 2W 2W 2W 5W
R53 121 12 600V
10K J2
1500 3
T1 CR9 CR13 C20 C
G DS2 21T ISL9R8120P2 220pF
R54 ISL9R8120P2
100
+18V 24 5 D
CR7 R9
15 1.0M C35
ISL9R8120P2 17T
J3 0.5W 100pF
1
1 21T
R1 R14 R17 R20 R29 R5
100K C17 R26
5 390 390 390 6810 681 3.32M
2W 1 10
DC INPUT 600V 2W 2W 2W C31
14 R27 2700pF
A DS1 392
DC 5T CR10 CR14 C21
21T ISL9R8120P2 220pF 2
J3 ISL9R8120P2 VFB 1
2 20 COMP
7 C28
19 0.01
17
6T U8
21T 7
R15 R18 R21 +18V VCC UC1844AJ
+18V 2 390 390 390 C29 C30
12
T2 Q1 2W 2W 2W 2.2 0.01
4 3 16
CR1 IXFK44N60
1N5819 CR11 CR15 C23
4 3 6T 21T 3
+18V VCC OUT 10 ISL9R8120P2 ISL9R8120P2 220pF CUR_SEN
Q8
MPF960
CR19 CR18 C36 R69
1N5819 1N4746A 0.01 10K
18V
S1950109 VA
Dimensions = mm (inches)
J2
ORN YEL F3 AC VOLTS
10A
EXCITER B
1
F4
U1 10A
AC LINE
FILTER 1 4
LINE 1 1 L L 1
3 *
3
L1 J3
LOAD F5 2.5mH
10A AC VOLTS
AC POWER 10A
LINE 8 5 POWER BLOCK 1
(170-270VAC) LINE 2 2 N N 2 t°
6
3
F6
4 10A RT1
GND G
**
FROM STATION 4
L3 J5
REFERENCE GROUND F9 2.5mH
10A AC VOLTS
10A
POWER BLOCK 2
t°
4
F10
10A RT3
J11 SIDE A
2
+24V 2 ***
CR1 5
1N4004 K1 L5 J7
F13 2.5mH
# AC ENABLE - 3 10A AC VOLTS
7 10A
POWER BLOCK 3
t°
5
F14
10A RT5
****
6
L7 J9
F17 2.5mH
10A AC VOLTS
DENOTES TB1 10A
POWER BLOCK 4
t°
DENOTES TB2 6
F18
10A RT7
DENOTES TB3
DENOTES TB4
*
L2 J4
F7 2.5mH
10A AC VOLTS
10A
POWER BLOCK 1
X = INSTALLED t°
F8
* ** *** **** 10A RT2
VR500/VRD750 X
**
VR1000/VRD1500 X X L4 J6
F11 2.5mH
10A AC VOLTS
VRD2250 X X X 10A
POWER BLOCK 2
VR2000/VRD3000 X X X X t°
F12
10A RT4
SIDE B
***
L6 J8
F15 2.5mH
10A AC VOLTS
10A
POWER BLOCK 3
t°
F16
10A RT6
****
L8 J10
F19 2.5mH
10A AC VOLTS
10A
POWER BLOCK 4
t°
S1950053 VF F20
10A RT8
Dimensions = mm (inches)
Assembly Detail – NAE89 Exciter Control Assembly (Front, Inside Front and
Top Views)
Issue 0.1 Not to Scale Figure MD-3 Sheet 1 of 1
Dimensions = mm (inches)
Assembly Detail – NAE89 Exciter Control Assembly (Bottom, Rear and Inside
Rear Views)
Issue 0.1 Not to Scale Figure MD-4 Sheet 1 of 1
5 NAUTEL ASSY 195-2050 +5V +15V +24V -15V C50 1
TP9 TP12 TP18 TP20
CONTROL/DISPLAY J3 C81 C111 C129 C134
C139
U5 J8 J10 BT1
C82
GRID1 J6
NAPC C64 C112
C120
1 1
5 TP24 R122 1
SER. C57
4 R102 R117 R123 U20 C115 C121 U23 R243
3 R103 R118 U12 R144 R151 R155 R162 R169 C102
TP30 E3 R250
C47 R145 R152 R156 R163 R170 R246
U21
2 C55 C65 R132 1
R146 R153 R157 R164 R171 C150 C160 C162
U8
R1 R23 1 R220 A B C154 C161 C163
C48 R104 C66 R133 CR1 R154 TP37 C133
R2 R24 A B C D E F G H I J
4 TP3 TP33 L6 R179 L12
J1
C127
CR4
U24
R37 R59 R110 C72 C98 R181 C116 U29 U33 U36
R3 R25 TP14 CR5 U19 C144
R38 R60 R71 R111 R121 R182 R200 C117 (U/S)
U13
R4 R26
U2
C73 CR6 C128
C31 C36 L7 R201
1
R5 R27 C19 R77 C58 C63 CR7 C137 C138
R6 R28 C32 U10 C103 CR14
C20 C41 TP25 R106 CR8
C3 C15 R49 R61 TP10 C84 CR15 TP47
R39 R107 C74 C104 CR9 R238
Y2
R7 C33 TP15 L4 R202
U25
R40 U9 R135 TP32 CR10
U30
U34
U37
R8 C16 R51 R62 C37 TP21 R96 GND TP45 U22 J9
TP16 C90 C105 CR11
U14
R9 R29 C21 R63 R97 R136 U18 (U/S)
R137 CR12
3 R10 R30
TP4
R52 R64
R78
R79
R88
C45
C51 C75
C78
C91
R148
C106
L8
CR13
R219
U4
C4 R31 R53 R65 R108 C85 A L15
R80 R98 R124 R189 TP40 R247
C5 TP5 R89 R112 C125 R222 C153
C17 C26 C34 R81 C56 C156 R248
GND C52 R190
R11 C8 C68 TP34 TP41 C118
U11
U35
C22 R54 R82 TP22 C59 Y1 K C146
R191
U15
R12 C38 R99 R223
TP42
R17 TP19 R113 C69 R149
U31
R13 R41 C27 R83 R192 L11 C119 C126 U26
U1
U3
U7
C9 R72 C53 R114 R125 R150 TP48
U38
R14 R42 C28 C42 R90 TP35 R193 TP43 TP46 R224
C39 R126 C79 C92 C94 TP52 C147 CR16
C6 C10 C23 C60 R194 TP44 GND R225
GND
TP31
R55 C43 R127 R138 TP51 C155 C159
C7 R18 R32 R66 R73 R105 L5 L14
R43 C29 C70 C86 C89 C96 C100 R183 R195 C109 C113 C123 C130 C135 TP49 R226
R15 R67 TP13 R84 C80 R229 C148
C11 Q3
2 R16 R44 R56 R68 R74 R85 R254
R128
R139
R165 R172 TP38 TP39 R196 R203 R207 R211 R215 R227 R230
U32
R129 R166 R173 R197 R204 R208 R212 R216 TP50 R239
U16
U17
TP1 TP2 TP6 TP7 TP8 TP11 TP17 TP23 C164 C141
C165
U27
C61 C71 C93 C97 C101 C110 C114 C124 C131 C136 R240
Q1 Q2 R231 +
R253 R115 R130 R255 R158 R167 R174 R198 R205 R209 R213 R217 R228 R241
1
C12 C18 C24 C30 C35 C40 C44 C46 R116 R131 R159 R168 R175 C107 C108 R199 R206 R210 R214 R218 R232 C149 R242 LS1
C166
R19 R33 R45 R252 C140 C158
R57 R69 R75 R86 R93 Q5 R184 J7 R233 C145
R20 R34 R46 J4
R58 R70 R76 R87 R94 R185
R251 R234 C151 C157
C49
U28
R21 R35 R47 TP28 R235 R244 R245
TP27 C54
R22 R36 R48 R236 C152
R186
TP26 R187 1
1 1
U6
M1950078 VA
A B C D E F G H I J K L M N O
Dimensions = mm (inches)
A
E
B
C
D
G
17
J9 J8
1 1
M1950010 V3
NAUTEL ASSY 195-3020
EXCITER INTERFACE
16
NAPI
R1
SER.
C1 C2 C3
GRID1
6
5 U1 U2 U3
4
3
15
2
1
A B C D E F TP1 TP2 R2
E1
C4
R3
2
14
Q1 C5
R4 R5
1
Q2 C6
R6
R7
U4 C7
Q3
R8
R9
C8
13
Q4 R10
R11 C9
Q5 C10 R12
+ C11
CR23 C12
R14
R13
R35 CR1
12
R36 1 E11
CR24 DGPS BEACON
CR2
E2 1 2
1 E10
DGPS BEACON
E3 1 2
CR3
R15
1
11
R32 CR26 R17
+ C13
C27
R18
TP3
J11
10 E4
1
DGPS BEACON
9
J4
R19
R20
R21
1
1 E5
A K DGPS BEACON
+
CR4 R22
8
C16
J16
R23
L2 1 E6
DGPS BEACON
R24
L3
R25
1
CR5 R26
Issue 0.1
C17
+
L4
7
R27
C18
CR6 R28
R29
A
C19
CR7
K
R30
TP4
C20
CR8
6
R39
1
C15
Q6 Q7
CR9 CR10
J5
K1 K2
5
1
CR11 CR12
A K A K
Not to Scale
CR13 CR14
J10
E7
1
4
DGPS BEACON
CR18
K A
+
A K
CR15
C22
L6
Figure MD-6
1 2 E8
L7
3
1 2 E9
+
CR16
C23
GRID2
L8
+
6
5
C24
CR17
4
3
CR19 CR20 2
2
K A K A 1
A B C D E F
R33 R34
Dimensions = mm (inches)
C25 C26
Sheet 1 of 1
CR21
Q8 CR22 Q9
1 1
1
J7 J3
EXT RF IN/
MSK (A) MSK (B)
J6 J7
MONITOR
RF FREQUENCY
J8 J9
REAR
INTERLOCK
CHARGER
MONITOR
RF OFF
INHIBIT
ALARM
AUDIO
AUDIO
RF ON
INPUT
TO-TALK
PDM
PRESS-
GND
GND
GND
GND
+ - + - + - + - + SHLD - + SHLD -
RS-422 RS-232 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
TB1
J4 J5 J21 1
1 1
C118
TP8
C119
C120
TP9
GND L11 C116
R118
C96
Q12 C101
U22
Q9 C97 C99 AGC BYPASS C117
R119 R115
1 E10 R80 R151
R111 R148
Q13 MONITOR NORM BYPASS C114
R112 LEVEL C103 C104
R120 R124 E11
R146
C90 1
R121 R128 C105 C110 C48
R125 R129
R113 R122 Q14
Q15
U20
4 J13 C93
U16
1
Q10 FRONT
C100 R161
R126 C111
C4
R96
R13 C45
R4 L2
J18
R14 L4 L6
R5 C6 C36 L3
R6 C29
C7 R27 C46 C52
C30 R81 J16 J17
U1
C1 C12 C39 C41
R8 C42 C47 C55 C58
R1 R17 C31 C35 C51 1 1
3
CR20
C2 C8 R63 R72 C59 R87 C80
C60 R92
R44 Q7
U21
C20 C69 C81
R82 C82
R9
U8
C70
TP2
R30
C61
C78 R91
U11
TP3 R83 C71
U3
R12 R34 R93 + C122
R77 R19 R84 R85 C72 R94
C9 CR2 C15 C16 C22 THRESHOLD R78 R98 TP5
CR11 CR22 C64 R88 R106 C98 R33 R132 R136
C3 R97 R99 C107
CR3 R22 CR12 R73 C54 C56 R86 C73 C88
U13
R100 C102 R137
R31 R74 R48 R156 C65 R89 TP6 C108 NORM NDB
1 R101 C89 R144 1 E13
C13 C21 C49 R79 C57
U10
U15
R133
2 C74 R102
U14
R158 R109
U17
R55 NORM NDB
T1 C66 TP7 R134
R23 R26 CR9 R90 TP12 1 E14
TP4 R103 R110
R28 C23 R139 R159 R135 GND
NORM NDB
A B E17 GND
C106
U9
R114 C75 R145 R160 C109 1 E15
TP1 R29 E4 NORM NDB
R32 R142
U18
GND R18 1 1
U6
U7
C17 CR10 R143
R38
TP10
1
C34 C40 C44
C50
E5
E6
E7
E8
1 R15
C10
L1
SINGLE
CR15 CR16 CR17
CR18 L7 L8 L9 C83 C94
TP11
C112
U19
C26 C79
U12
R16
R162 E18
R50 R53 R70 R75 C67 C76 C84 C95 R130 R138 C113
1 DIFF R76 C63 C68 C77 R131
CR1 R51 R54 R71 R105 C85
NORM BATTERY C62 R123
1
M1950124 V1
A B C D E F G H I J K L
Dimensions = mm (inches)
TP11
C11 TP3
C5 R37 R4
C13
3 2 1
+
+ +
U4
C9
TP1
C3 C18 R3
L3
L1 C6 C22
U9
TP14
TP5
C8 R48
C21
R1
C27
C45
C14 DUMP Q1
R59
U2
R25
R5
U1 C41 R58
1
CR2
R57
R11
R29 R56
L8 R26
TP2
R8
R34 R64
C28
+
+
R73 C25 C34
C64
C36 C43 R35
C65
U6
R30
P1
C26
R9
R14 R10 +
U8
TP19
U12 U5 C20 C38
R76 E1 C44 C23
C46
R72 B
A L7
R71
C42
1
R70 R68 + C33
C47 TP12 U3 L6
TP7
C59 R67 R22 R44
C58 R60 TP10 R38 +
C39 C37
CR3 R62 C54
R42
C29
TP9 TP8
R65 + R52
L4
Q2 C10 U10 R39
U7
C48
R27
+
Q4 C52 TP4
C56
C60
C50
R54 R31
TP15 Q5 R2 R12
GND CR5 C55 R53
GAIN C71 R13
TP17
R74 R69 +
C4 R47 R15
Q10 C63
R46
R77 K1 C17
TP13
+ R49
L2
R78 C12 TP16 U13
C24
C30
CR4 GND
C62
TP18 R55
+ U11
R50
C2 R75 C53
R51
R66 Q3
C16
C51
+
Q6
C57
C61
R61 C66 NAUTEL ASSY 197-3040
C49
Q7 INTERPHASE PDM DRIVER
R63
NAPM
SER.
M1970044 V2
Dimensions = mm (inches)
CR15
CR18
+
CR16
K A
R11
C26
R5
R6
E1
E2
R25
1
RT1
J3
4 +
J2
R12
NAUTEL ASSY 195-7025 C5
C1
CR13
CR14
LVPS BUCK CONVERTER
R18
R22
R23
R24
+
T1
NAPS SER.
CR8
C8 C24
C6 C4
C25
Q1
U1
U2
M3 PAN HEAD SCREW R8 R4 8 5
3
Q2
R10 R2 R13
A
6 1
CR7
SEMICONDUCTOR R9 R3 CR9 R17
K
HEATSINK CR11 R19 R20
K A R1
R7 + R14
M3 WASHER 6 1 + C23
R16
#4 BELLEVILLE WASHER C21 C3
C17 L1
M3 HEX NUT C22
2 C18 R27
C19 +
Q1 & Q2 MOUNTING DETAIL +
L2
CR17
TORQUE ATTACHING HARDWARE TO
C12
C14
CR12
C9 13 1
RT4
4.0 INCH POUNDS (0.45 NEWTON METRES)
RT3
7
R29
CR6
C13
C2 C20
R15
C10
C11
J1
1
C15
C16
7 13
C7 +
CR10 R28
+ R21
M1950051 VA
A B C D E F G
Dimensions = mm (inches)
R81
TP5
C76 R29 CR3 R59 R69 R76 C85
C18
C44
C69
CR12 C45
R85 C70
U8
U14
6 R23 R16
R87
C81 C29
R11 R2
C80 CR11 R80 C77
C19 R15
R84 R22 C71 R61
R1 R12
R14
R79 CR9
C15
TP4
R86
R8
R9
R30 C4
J3
R45 R54 C47
C30 1
Q1 R62
R18 R31 C63 C72
C48
C16
C31
U9
C49
5
U17
U20
C1
U1
C17 CR7
C32 C84
R19
R60
C55 R71
1 E3 R55 C74
R41
TP1
R72 C60
A B R44 R56
R68
C14
U18
C5
R47
C78 R32
C34 C33
C6 U5
U10
R73
C61
C13 R82
C7
C41 R74
U19
C75
R75
C35 C54
4 C8
CR1
R33
TP9
GND
R83
J4 C79
C39 C62 NORMALCR13
R5
U6
R34 R50
U15
R6 R35 R51
1 E2
KEYED
R7 R20 R36 R52
CW
C10
R53
CR8
C11 CR2 1 E1
R10 R21 A B
C65
U16
C12 C20
1
R3 R38
CR4
TP6
3 R39 CR6
C21
C2 C58
CR5
C64
R24
U3
R4
C36
R40 C59 L1
C3 C22 L2
C23 C56
C46
R25 L3
C24 Y1 C66
U4
C25 R46
C67
2 KEYER OK DS1 U7
C40 C57
C9 R13
C26 R64
C27 C50 R77
U2
CR10
U11
C28 C51 R78
R26 R65
TP8
R42 R57 R66 C73
C68
R43 R58 C52
1
C82 C37 C53 NAPE76
C42
1
J2
C83 C38 U13 SER.
C43
TP2
R27 R67
U12
R28 EXCITER MONITOR/
TP3
GENERATOR
M1950130 V1
A B C
Dimensions = mm (inches)
J1
1
NAUTEL ASSY 195-7030 1 L1
DC-DC POWER SUPPLY 2
2
C3
CR3
C1 + C2 C4 C5
A K
R2 CR1
1 2 3
3 2 1
CR4
U1
U2
R3
A K
R1 CR2 R4
NAPS SER.
M1950076 VA
A B C
Dimensions = mm (inches)
A2
A4 A4
A6
A5
Dimensions = mm (inches)
A4
A5
A3
A2
Dimensions = mm (inches)
U4
C5 C9 C10 R19
C38 R31 R35
C37 C11
U6
U8
J1
U5
C6
1
J3
C16 R24 R33 TP3 R37
C7
U2
C13 C26 C33
R25
C14
INSTALL
1
R1 R4 R5 C2 Y1 TP2
+
DS1
R21 C17
2 GND
P1
Q1 C3 C4 C8 R22 R23
NAUTEL ASSY 195-4020
MODULE
TP1 R6 R8 TP6
R2 POWER MODULE CONTROL/INTERFACE
+
DS2
ON
NAPI
SER. R26
FAULT
R3 RT1 C36
+
DS3
R27
C27 CR4 C34 TP4
R28
J2 U7 U9 C35
C1 J4
1 R7 C20 (U/SIDE)
R38 U10
C21 CR3 C29
1
Q2 R39
1 R10
1
A B C D E F G H I J K L M N O
1
J6
REAR
J5
U9 3 2 1
1 2 3 U7
M1950019 VA
Dimensions = mm (inches)
CR7
J3
FORWARD CONVERTER 1
T1
20
1
L3
NAPS
K
SER.
C4
7 R15 R18 R21
M3 PAN HEAD SCREW
C17
RV1
C23
#4 BELLEVILLE WASHER
R50
C11
C9
G
G
M3 WASHER RV2
Q2
Q1
D
D
SEMICONDUCTOR
D
A K RV3
D
S
S
CR11
HAT46 6 B A
HEATSINK
10 11
CR6
Q1 & Q2 MOUNTING DETAIL
CR15
TORQUE ATTACHING HARDWARE TO K A
6.0 INCH POUNDS (0.68 NEWTON METRES)
K
R14 R17 R20 3
5 2 2
A
F 1 3 1 3
C21
U2 U1
2 T3 1
DS1
C43
C13
L4 AC IND
A K 4
CR10 7 4 + R7
S
+
8 3
4 T2 CR12 R22
R1
R12 R23
M3 HEX NUT
CR14 CR18 CR19 R63
K A
10 1
C36 C37
#4 BELLEVILLE WASHER
J1
R19 R16 R13 F R69
A K
M3 WASHER CR20 C26
Q8 R30
C20
C15 C12
R57 U3 R35
C44
1
C27
HEATSINK C29
3
CR4
L5
R58 C30 U8 C19
HAT46 + +
C10 C2 C32
A K
C28
SEMICONDUCTOR S CR2 C38
CR9 C31 R29
R43
CR1 C35 R64 C41 U11
M3 PAN HEAD SCREW
R5 R28 R52
C5 L1 C33
U9 U7
CR17
CR6, CR7, U1, U2 & U10 MOUNTING DETAIL 2 CR13
Q4 C1
R65
TORQUE ATTACHING HARDWARE TO K A R62 R37
J2
F RT1
4.0 INCH POUNDS (0.45 NEWTON METRES) C6 R49 R39 U6
R55
C25
+ + R10 R44 R3 R61
R41 Q5 R53
E1 E1 U5
C45
CR5
C7
1
R46 C14 R67 C34 R4
CR21
R33
M1970079 V2
A B C D E F G H I J K L M N O
Dimensions = mm (inches)
U1
12345
6
U1
1
R6
C1
R4 R7
R1
C3
C7
R2
Q5
R3
R2
CR5 C4
F1
M3 HEX NUT
E1 R5
#4 BELLEVILLE WASHER
M3 WASHER
Q1 S G Q3
SEMICONDUCTOR
G
S
D
Q1
Q3
INSULATOR
D
G S
S
CHASSIS
CR1 CR3
SER.
POWER AMPLIFIER
T1
TORQUE ATTACHING HARDWARE TO
C2
4.0 INCH POUNDS (0.45 NEWTON METRES)
NAAA
CR2
Q4
S G
G
S
D
Q2
Q4
D
D
G
S
G S
Q2
CR4
C5
E2
E3
C6
M1970016 V1
Dimensions = mm (inches)
CR13
R9
R10
R11
R1
CR9
CR12
J1
4 RED
3
RED
5 CR3 T1
CR4
CR1 1
WHT
R2
R3
CR2 2
1
WHT
C1
C3
C2
CR5
C9
R5
R4
4
C7
U1
TP1
GND
+
CR6
R7
3 C4
C8
E1
+
+
2
E2
C5 C6
M1950121 V1
A B C D
Dimensions = mm (inches)
1 1 1
C1
C2
Q1
Q2
R2
R4
R1
R3
1 1 CR1 1 1
E1
E2
E3
CR2
J4 J5 J6 J7
M1950028 VA
Dimensions = mm (inches)
2 L1 2 L2
E2 E23
3 3
E3 E24
JUMPER SETTINGS
6 4 4
Frequency E20 E21 E33 E36 E15 E17 E4 E25
(kHz) to to to to to to 5 5
190.0 -209.0 E1 E22 E31 E34 E16 E18 E5 E26
C10
C12
C15
C16
E12 E16
C2 C6
2
E18 C3 C7
C11
C13
C14
C9
NAPF C4 C8
SER.
1 E20
M1950024 V2
A B C D E F G H I J K L
Dimensions = mm (inches)
1
NAPS
24
SER.
K
CR7
A
1
20
7
C17
G
G
T4
Q2
Q1
D
D
D
D
T1
S
R18
6 R21 R15
12
A K
CR11
10
13
11
K
CR6
3
CR15
5
J3
A
K A
C23
T3
2 1
1
R17 4 7 4
R1
8 3
R20 R14
4 C40 T2 CR8 CR12 R22
A K R8 R12 R23
CR10 CR18 CR19 R63
10 1
DS1
C36 C37
CR14
K A R69 DS1
1 CR4 C26 AC IND
Q8 R30
C21
24 R57 U3 R35
C27
C29
3
R58 C30 U8 C19
C
R16 C10 C2 C32
C28
D CR2 C3
C31 R29
R43
R19 R13
CR1 C35 R64
A K R5
CR9 R9 R26
L2
2 R27 L1
CR13
J2
K A
C1
C20 RT1
R55
C25
R53
R54
12 U10 R2
1 1 2 3
1
13 DS2
CR16
+18V
M1950110 VA
A B C D E F G H I J K L M
Dimensions = mm (inches)
RSIM Messages
26 and 27
Nautel Limited
10089 Peggy's Cove Road,
Hackett's Cove, NS, Canada B3Z 3J4
T.877 6 nautel (628835) or +1.902.823.2233
F.+1.902.823.3183 info@nautel.com
Nautel Inc.
201 Target Industrial Circle, Bangor ME 04401
T.877 6 nautel (628835) or +1.207.947.8200
F.+1.207.947.3693 info@nautel.com
e-mail: support@nautel.com
www.nautel.com
The following information applies to RSIM messages #26 and #27. It is additional to that
provided in the RTCM Standard 10401.2 for Differential Navstar GPS Reference Stations
and Integrity Monitors (RSIM) document.
RSIM #26: GENERAL TEXT MESSAGE (ADDITIONAL CONTROL AND STATUS)
Usage:
• The RSIM26 is used by the CS to send controls to the TR. These controls are:
1) Set System Time
2) Enable/Disable time stamping
3) Enable/Disable the Automatic Reset feature
4) Specify the Automatic Reset Interval
5) Enable/Disable the AC and DC Supply Sources
6) Execute Tests of the Standby TR Equipment
7) Configure the Inductive/Resistive Tuning of the TR’s ATU
8) Enable/Disable TR-ATU Constant Antenna Current power control
• The TR also sends RSIM26 whenever there is a request from the CS or at a specified
query interval.
Field # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
$PRCM,26,hhmmss.s,a,a,hhmm,a,x,x,x,x,xx,aa,xx,xx,aa,aa,xx*hh<CR><LF>
Field 1: UTC Time. The data type for this field is fixed/variable length time (000000.0 –
235959.9). The CS uses this field to set the TR’s clock. If time stamping is enabled, the
TR responds in this field with its clock’s current time. Otherwise, the TR is expected to
leave this field NULL.
Field 2: Time Stamp Enable. The CS can use this field to enable and disable the time
stamping of messages. The TR responds in this field to report whether time stamping is
currently enabled or disabled.
0 = Not enabled
1 = Enabled
The data type for this field is fixed alpha (0, 1).
Field 3: Automatic Reset Enable. The CS uses this field to specify whether the
Automatic Reset is enabled or not. The TR responds in this field with its current setting.
0 = Not Enabled
1 = Enabled
The data type for this field is fixed alpha (0,1).
Field 4: Automatic Reset Interval. The CS uses this field to specify the number of hours
and minutes that the TR waits after a failure before it attempts a reset. The TR responds
in this field with its current setting. The data type for this field is fixed/variable length
time (0001 – 2400).
Field 5: Supply Source Control. The CS uses this field to specify the supply sources that
currently should be selected. The TR responds in this field with its current setting. The
data type of this field is variable length alpha (NONE, AC, DC, BOTH).
Field 6: DC Auto-Disconnect – Disconnect Voltage Level. The CS can use this field to
specify the voltage level where the TR should automatically disconnect from the DC
supply. The TR responds in this field with its current setting. The data type of this field
is variable length integer (0 – 255).
Field 7: DC Auto-Disconnect – Reset Voltage Level. The CS uses this field to specify
the voltage level where the DC supply is reconnected after there has been an auto-
disconnect from the batteries. The data type for this field is variable length integer (0 –
255).
Field 8: Test Standby Side. The CS uses this field to execute a test of the standby TR
equipment. The TR responds in this field with a text message giving the state of the
standby test.
For CS to TR communication, the data type for this field is fixed alpha (0,1).
0: No change in Standby Equipment state
1: Execute Test of Standby Equipment
For TR to CS communication, the data type for this field is variable length alpha (NO
TEST, STANDBY PENDING, STANDBY FAILED, STANDBY OK).
NO TEST: The standby equipment is not currently under test,
and the final result from the most recent set of tests
(if any) has previously been returned.
For CS to TR communication, the data type of this field is variable length alpha (STOP,
INCREASE, DECREASE).
STOP: Stop the servo.
INCREASE: Begin slewing the servo higher.
DECREASE: Begin slewing the servo lower.
For TR to CS communication, the data type of this field is variable length alpha (LOW
END STOP, DECREASING, STATIONARY, INCREASING, HIGH END STOP).
LOW END STOP: The servo cannot slew any lower.
DECREASING: The servo is slewing lower.
STATIONARY: The servo is stationary.
INCREASING: The servo is slewing higher.
HIGH END STOP: The servo cannot slew any higher.
Field 10: ATU Inductive Coil Tuning. The CS must leave this field NULL. The TR
responds in this field with the current tuning state of the inductive coil. The data type of
this field is variable length alpha (NORMAL, HIGH, LOW).
NORMAL: The inductive coil is optimally tuned.
HIGH: The inductive coil has been slewed too high.
LOW: The inductive coil has been slewed too low.
Field 11: ATU Inductive Coil Automation. The CS uses this field to enable/disable the
ATU automatic tuning feature for the inductive coil. The TR responds in this field with
the current state of this setting. The data type of this field is fixed alpha.
0: Not enabled
1: Enabled
Field 12: ATU Resistive Coil Condition. The CS uses this field to slew the resistive coil
servo higher or lower, or set the servo stationary. The TR responds in this field with the
resistive servo coil’s current state.
For CS to TR communication, the data type of this field is variable length alpha (STOP,
INCREASE, DECREASE).
STOP: Stop the servo.
INCREASE: Begin slewing the servo higher.
DECREASE: Begin slewing the servo lower.
For TR to CS communication, the data type of this field is variable length alpha (LOW
END STOP, DECREASING, STATIONARY, INCREASING, HIGH END STOP).
LOW END STOP: The servo cannot slew any lower.
DECREASING: The servo is slewing lower.
STATIONARY: The servo is stationary.
INCREASING: The servo is slewing higher.
HIGH END STOP: The servo cannot slew any higher.
Field 13: ATU Resistive Coil Match. The CS must leave this field NULL. The TR
responds in this field with the current matching state of the resistive coil. The data type
of this field is variable length alpha (NORMAL, HIGH, LOW).
NORMAL: The resistive coil is optimally matched.
HIGH: The resistive coil has been slewed too high.
LOW: The resistive coil has been slewed too low.
Field 14: ATU Resistive Coil Automation. The CS uses this field to enable/disable the
ATU automatic matching feature for the resistive coil. The TR responds in this field with
the current state of this setting. The data type of this field is fixed alpha.
0: Not enabled
1: Enabled
Field 15: Antenna Current. The CS must leave this field NULL. The TR responds in
this field with the antenna current, in Amps, currently being reported by the ATU. The
data type of this field is a variable-length number (0.0 – 30.0).
Field 16: Constant Antenna Current power control. The CS uses this field to
enable/disable automatic power control to maintain a fixed antenna current. The TR
responds in this field with the current setting. When Constant Antenna Current power
control is enabled, the present Antenna Current sample is taken as a reference point;
subsequently, the TR will automatically adjust Fwd Pwr in order to maintain the Antenna
Current at that fixed level. The data type of this field is a fixed alpha.
0: Not enabled
1. Enabled
NOTES:
To set the system time, Field #1 is sent by the CS with the desired time.
Otherwise, Field #1 is left null.
When sent from the CS to the TR, any field(s) may be left null, resulting in no
change to the current setting at the TR.
RSIM #27: EQUIPMENT LOGISTICAL PARAMETERS
Usage:
• The TR sends RSIM27 for the purpose of conveying the TR’s firmware version.
Field # 1 2 3
$PRCM,27,c---c,c---c,c---c*hh<CR><LF>
Field 1: Firmware Title. This field conveys the firmware title as a variable-length alpha.
(eg. Vector Transmitter DGPS)