Professional Documents
Culture Documents
Jonsered 2054 Operator's Manual
Jonsered 2054 Operator's Manual
Jonsered 2054 Operator's Manual
Always wear:
• Approved protective helmet
• Approved hearing protection
• Protective glasses or visor Regular cleaning is required.
2 – English
Downloaded from www.Manualslib.com manuals search engine
CONTENTS
Before using a new saw Contents
• Read the instructions carefully. Key to symbols .................................................................. 2
• Check cutting equipment is correctly fitted and adjusted. See Safety instructions
page 25.
• Refuel and start the saw. Check the carburetor setting. See Personal protective equipment ....................................... 4
pages 26-29. Chain saw safety equipment ........................................... 4
• Do not use the saw until sufficient chain oil has reached the Inspecting, maintaining and servicing chain saw safety
chain, see page 14. equipment ............................................................................ 8
IMPORTANT! If the carburetor mixture is too lean it greatly Cutting equipment ............................................................ 10
increases the risk of engine failure. How to avoid kickback ..................................................... 16
Poor maintenance of the air filter will cause carbon build-up on
the spark plug and lead to difficult starting. General safety precautions ............................................ 18
If the chain is badly adjusted it will cause increased wear or General working instructions ......................................... 19
damage to the bar, drive sprocket and chain. What is what?
What is what? .................................................................... 24
Maintenance, replacement, or repair of the emission
control devices and systems may be performed by any Assembly
nonroad engine repair establishment or individual. Mounting guide bar and chain ........................................... 25
Fuel handling
!
Fuelmix .............................................................................. 26
WARNING!
Fuelling .............................................................................. 27
Under no circumstances may the design of
the machine be modified without the permis- Start and stop
sion of the manufacturer. Always use genuine Start and stop .................................................................... 28
spare parts/accessories. Non-authorized Maintenance
modifications and/or accessories can result Carburetor ......................................................................... 29
in serious personal injury or the death of the Starter device .................................................................... 30
operator or others. Air filter .............................................................................. 31
Your warranty does not cover damage or Spark plug ......................................................................... 31
liability caused by the use of non-authorized Muffler ................................................................................ 31
accessories or replacement parts. Cooling system .................................................................. 32
Centrifugal cleaning ”Turbo” .............................................. 32
Winter use ......................................................................... 32
Needle bearing maintenance ............................................ 32
Daily maintenance ............................................................. 33
Weekly maintenance ......................................................... 33
Monthly maintenance ........................................................ 33
Technical data
2054 .................................................................................. 34
Federal Emission Control Warranty Statement
Your warranty rights and obligations ................................. 35
English – 3
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
• PROTECTIVE HELMET
• HEARING PROTECTION 2 Throttle lock
• PROTECTIVE GLASSES
OR VISOR
• GLOVES WITH
SAW PROTECTION
3 Chain catcher
• PROTECTIVE TROUSERS
WITH SAW PROTECTION
4 Right hand guard
4 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
1 Chain brake and front hand guard 2 The front hand guard is
YOUR chain saw is equipped with a chain brake that is desig- not designed solely to
ned to stop the chain immediately if you get a kickback. activate the chain brake.
The chain brake reduces the risk of accidents, but only You can Another important safety
prevent them. feature is that it prevents
the chain from hitting your
Take care when using your left hand if you lose your
saw and make sure the grip on the front handle.
kickback zone of the bar
never touches any object.
B
The brake is applied
when the front hand
guard (B) is pushed
forwards.
D 5 As mentioned in section A,
kickback can be very
sudden and violent.
Most kickbacks are
minor and do not always
activate the chain brake.
If this happens you
should hold the chain
saw firmly and not let
go.
English – 5
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
6 The way the chain brake is triggered, either manually or 2 Throttle lock
automatically, depends on the force of the kickback and the The throttle lock is designed
position of the chain saw in relation to the object that the to prevent accidental opera-
kickback zone of the bar strikes. tion of the throttle control.
When you press the lock (A)
(i.e. when you grasp the A
If you get a violent handle) it releases the throttle
kickback while the trigger (B).
kickback zone of the bar When you release the handle
is farthest away from you the throttle trigger and the
the chain brake will be throttle lock both move back
activated by the to their original positions. This
movement of the movement is controlled by two
counterweight (INERTIA independent return springs.
ACTIVATED). This arrangement means that B
the throttle control is
automatically locked at the
idle setting when you release
the handle.
3 Chain catcher
The chain catcher is designed
If the kickback is less
to catch the chain if it snaps or
violent or the kickback
jumps off. This should not
zone of the bar is closer
happen if the chain is properly
to you the chain brake will
tensioned (see section on
be activated manually by
”Assembly”) and if the bar and
the movement of your left
chain are properly serviced
hand.
and maintained.
(See section on ”General
working instructions”).
6 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
5 Vibration damping system 6 Stop switch
Your chain saw is equipped Use the stop switch to switch
with a vibration damping off the engine.
system that is designed to
minimise vibrations and make
operation easier.
English – 7
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
Inspecting, maintaining and servicing 3 Checking the automatic brake
chain saw safety equipment
8 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
2 Throttle lock 4 Right hand guard
English – 9
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
7 Muffler CUTTING EQUIPMENT
Never use a chain saw This section describes how to choose and maintain your cutting
that has a faulty muffler. equipment in order to:
• Reduce the risk of kickback.
• Reduce the risk of the chain breaking or jumping.
• Obtain maximum cutting performance.
• Extend the life of cutting equipment.
10 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
1 Cutting equipment designed to minimise C Some terms that describe the bar and chain
When the cutting equipment supplied with your saw becomes
kickback worn or damaged you will need to replace it. Use only the type
of bar and chain recommended by us. See the ”Technical data”
Bar
The only way to avoid kickback is to make sure that the kick- • LENGTH (inches/cm)
back zone of the bar never touches anything.
By using cutting equipment with “built-in” kickback protection • NUMBER OF TEETH ON
and keeping the chain sharp and well-maintained you can BAR TIP SPROCKET (T).
reduce the effects of kickback. Small number = small tip
radius = low-kickback
A Bar
The smaller the tip radius the • CHAIN PITCH (inches)
smaller the kickback zone and The spacing between the
the lower the chance of drive links of the chain must
kickback. match the spacing of the
teeth on the bar tip sprocket
and drive sprocket.
SIDE LINK
Saw chain
STANDARD
English – 11
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
2 Sharpening your chain and adjusting It is very difficult to sharpen a
chain correctly without the
raker clearance right equipment. We
recommend you use a file
• CUTTING ANGLE
TOO SMALL
A
• The cutting part of the chain B • FILE DIAMETER
is called the CUTTING LINK TOO SMALL
and this consists of a
CUTTING TOOTH (A) and
the RAKER LIP (B). The
cutting depth is determined
by the difference in height
between the two. B Sharpening cutting teeth
1
5
See the ”Technical data” section for information about
sharpening your saw chain.
12 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
C General advice on setting raker clearance D Setting the raker clearance
English – 13
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
4 Lubricating cutting equipment
combination spanner.
Then tighten the nuts by A Chain oil
hand as tight as you can. • Chainsaw chain oil must demonstrate good adhesion to the
chain and also maintain its flow caracteristics regardless of
whether it is warm summer or cold winter weather.
2 Raise the tip of the bar
• As a chainsaw manufacturer we have developed an optimal
and stretch the chain by
chain oil which, with its vegetable oil base, is also
tightening the chain
biodegradable. We recommend the use of our own oil for
tensioning screw using
both maximum chain life and to minimise environmental
the combination spanner.
damage.
Tighten the chain until it
hangs slack on the
• If our own chain oil is not available, standard chain oil is
underside of the bar.
recommended.
14 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
C Checking chain lubrication E Lubricating the clutch drum bearing
B RING (replaceable) A
• Lubricate the bar tip
sprocket each time you
refuel. Use the special Regularly check the
grease gun and a good degree of wear on the
quality bearing grease. drive sprocket. Replace if
wear is excessive.
B
Replace the drive
sprocket whenever you
replace the chain.
English – 15
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
H Bar HOW TO AVOID KICKBACK
!
Kickback can happen very suddenly and
violently; kicking the saw, bar and chain back
at the user. If this happens when the chain is
moving it can cause very serious, even fatal
Check regularly:
injuries. It is vital you understand what causes
kickback and that you can avoid it by taking
care and using the right working technique.
• Whether there are burrs on
the edges of the bar.
Remove these with a file if
necessary.
What is kickback?
The word kickback is used to
describe the sudden reaction
that happens when the upper
quadrant of the tip of the bar
(known as the “kickback zone”)
touches an object and the
• Whether the groove in the saw is kicked backwards.
bar has become badly worn.
Replace the bar if
necessary.
!•
MOST CHAIN SAW ACCIDENTS HAPPEN
WHEN THE CHAIN TOUCHES THE
OPERATOR.
16 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
General rules 6 Take great care when you
1 If you understand what kickback is and how it happens then cut with the top edge of
you can reduce or eliminate the element of surprise. By the bar, i.e. when cutting
being prepared you reduce the risk. Kickback is usually from the underside of the
quite mild, but it can sometimes be very sudden and object. This is known as
violent. cutting on the push
stroke. The chain tries to
push the saw back
2 Always hold the saw towards the user.
firmly with your right hand
on the rear handle and Unless the user resists
your left hand on the front this pushing force there is
handle. a risk that the saw will
move so far backwards
Wrap your fingers and that only the kickback
thumb around the hand- zone of the bar is in
les. You should use this contact with the tree. This
grip whether you are will cause kickback.
right-handed or left-
handed. This grip Cutting with the bottom
minimises the effect of edge of the bar, i.e. from
kickback and lets you the top of the object
keep the saw under downwards, is known as
control. cutting on the pull stroke.
English – 17
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
GENERAL SAFETY PRECAUTIONS 7 FUEL SAFETY
(Refuelling, fuel mixture, storage.)
1 Chain saws are designed solely for cutting wood. The only
cutting equipment that can be used with this chain saw are
!
the combinations of bars and chains recommended in the
Fuel and fuel vapour are highly inflammable.
”Technical data” section.
Take care when handling fuel and chain oil.
2 Never use a chain saw if Keep away from naked flames and do not
you are tired, if you have breathe in fuel vapour.
drunk alcohol, or if you
are taking medication that
affects your vision, your
judgement or your co- • Never try to refuel the saw
ordination. while it is running.
!
foot. Grasp the front handle The risk of accident is increased if you use the
firmly using your left hand. wrong cutting equipment or a chain that is not
Make sure the chain saw is sharpened correctly. Using the wrong combi-
steady and the chain is not nation of bar and chain can increase the risk
touching the ground. Then of accidents!
grasp the starter handle
with your right hand and pull
the starter cord.
18 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
GENERAL WORKING INSTRUCTIONS 4 Check the area around
you for possible obstacles
such as roots, rocks,
Important
1 Before using a chain saw you must understand the effects of
kickback and what causes it. (See the section on ”How to
avoid kickback”.) 5 Take the utmost care
when cutting through
2 Before using a saw you must understand the difference branches or logs that are
between sawing with the top and bottom edges of the bar. in tension. A log or branch
(See the section on ”How to avoid kickback”.) that is in tension can
suddenly spring back into
its natural position before
1 Basic safety rules or after you cut it. If you
1 Look around you: stand on the wrong side
or start cutting in the
• to make sure there are no wrong place it may strike
people, animals or other you or your chain saw.
objects nearby that might This could make you lose
affect your work. control and cause a
serious accident.
• to make sure that none of
the above might come within
reach of your saw or be
injured by falling trees.
English – 19
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
2 Basic cutting technique Two factors decide whether the chain will jam or the log will
split. The first is how the log is supported and the second is
General whether it is in tension.
• Always use full throttle when cutting!
In most cases you can avoid these problems by cutting in two
• Reduce the speed to idle after every cut (running the stages; from the top and from the bottom of the log. You need
engine for too long at full throttle without any load can lead to to support the log so that it will not trap the chain or split during
serious engine damage). cutting.
• Cutting from above = Cutting on the pull stroke.
20 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
2 The log is supported at one 3 Tree felling technique
end. There is a high risk
!
that it will split.
It takes a lot of experience to fell a tree.
Inexperienced users of chain saws should not
fell trees. NEVER ATTEMPT A TASK YOU ARE
UNSURE OF.
Bend
Wind direction
Limbing
When limbing thick branches 2 Arrangement of branches
you should use the same 1
approach as for cutting. Weight of snow
Cut difficult branches piece by 3
piece.
You may find you are forced to let the tree fall in its natural
direction because it is impossible or dangerous to try to make it
fall in the direction you first intended.
Another very important factor, which does not affect the felling
direction but does affect your safety, is to make sure the tree
has no damaged or dead branches that might break off and hit
you during felling.
English – 21
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
C Clearing the trunk and preparing your retreat FELLING CUT
The felling cut is made from the opposite side of the tree and it
Remove any branches that must be perfectly horizontal. Stand on the left side of the tree
are in the way. To do this it is and cut with the bottom edge of the bar.
best to work from the top
down and keep the trunk
between you and the chain
saw. Never limb above Make the FELLING CUT
shoulder height. about 3-5 cm (1.5-2 inches)
above the flat section of the
DIRECTIONAL CUT.
22 – English
Downloaded from www.Manualslib.com manuals search engine
SAFETY INSTRUCTIONS
We recommend that you use 4 Freeing a tree that has fallen badly = high
a bar that is longer than the
diameter of the tree, so that accident risk
you can make the FELLING
CUT and DIRECTIONAL CUT A Freeing a “Trapped tree”
with single cutting stokes. The safest method is to use a winch.
(See ”Technical data” to find A Tractor-mounted B Portable
out which lengths of bar are
recommended for your saw).
!
Preparations:
UNLESS YOU HAVE SPECIAL TRAINING WE
ADVISE YOU NOT TO FELL TREES WITH A a) Work out which way the tree or branch will move if released
DIAMETER LARGER THAN THE BAR LENGTH and where the natural “BREAKING POINT” is (i.e. the place
OF YOUR SAW! it would break if it was bent even more).
E Limbing
English – 23
Downloaded from www.Manualslib.com manuals search engine
WHAT IS WHAT?
3
2
1
27
7
10
24
5
4
6
11 8 22
21 9
20 12 J O N S E R E D S E R V I C E
25
19 18 16 15 13
17 14
23
26
What is what?
1. Cylinder cover. 15. Saw bar.
3. Front hand guard. 17. Chain catcher. Catches chain if it jumps or breaks.
5. Chain oil tank. 19. Right hand guard. Protects right hand if chain breaks or
jumps.
6. Starter handle.
20. Throttle control.
7. Adjuster screw, carburetor.
21. Throttle lock. Prevents accidental operation of throttle
8. Choke control/Start throttle lock. control.
9. Rear handle. 22. Switch for heated handles.
10. Stop switch. Ignition on/off switch. 23. Combination spanner.
11. Fuel tank. 24. Chain tensioning screw.
12. Muffler. 25. Operator´s manual.
13. Bar tip sprocket. 26. Bar guard.
14. Saw chain. 27. Decompression valve
24 – English
Downloaded from www.Manualslib.com manuals search engine
ASSEMBLY
Mounting guide bar and chain
English – 25
Downloaded from www.Manualslib.com manuals search engine
FUEL HANDLING
Fuelmix Mixing
• Always mix the gasoline
IMPORTANT! The chain saw is equipped with a two-stroke and oil in a clean container
engine and must always been run using a mixture of petrol and intended for fuel.
two-stroke engine oil. It is important to accurately measure the
amount of oil to be mixed to ensure that the correct mixture is • Always start by filling half
obtained. When mixing small amounts of fuel, even small the amount of the gasoline
inaccuracies can drastically affect the ratio of the mixture. to be used. Then add the
entire amount of oil. Mix
!
(shake) the fuel mixture.
Always provide for good ventilation when Add the remaining amount
handling fuel. of gasoline.
Two-stroke oil
• For the best results use JONSERED two-stroke oil, which is
especially developed for chain saws. Mixing ratio 1:50 (2%).
Chain oil
• The chain lubrication
• Never use two-stroke oil intended for water cooled outboard system is automatic. Always
motors, so-called, outboard oil. use special chain oil with
good adhesive
• Never use oil intended for four-stroke engines. characteristics.
• In countries where no
special chain oil is available,
transmission oil EP 90 can
be used.
English – 27
Downloaded from www.Manualslib.com manuals search engine
START AND STOP
Start and stop Start
Grip the front handle with your
! WARNING!
• Never start the saw engine without the bar, chain and
left hand and hold the saw
down by putting your right foot
in the rear handle. Pull the
starter handle with your right
hand and pull out the starter
clutch cover (chain brake) assembled - or else the
clutch can come loose and cause personal injuries. cord slowly until the starter
• Always move the saw away from the fueling area pawls engage. Then pull
before starting. sharply.
• Place the saw on clear ground and make sure that the
chain is not contacting anything. Also, make sure that
you have a secure footing. Push in the choke control
• Keep people and animals well away from the working immediately when the engine
area. ignites and make repeated
starting attemps. When the
engine starts, rapidly give full
Cold engine throttle. Then the throttle latch
CHAIN BRAKE: will disengage.
Disengage the chain brake by
pulling the hand guard
towards the front handle.
IGNITION:
Move the ignition switch to
startposition.
Stop
CHOKE: The engine is stopped by
Set the choke control in choke switching off the ignition.
position. (Move the ignition switch to
stopposition.)
FAST IDLE:
Combined choke/fast idle is
received when the choke is
moved to choke position.
Warm engine
Use the same procedure as
for starting cold engine but
without choke. Fast idle is
recived by first set the choke
control in choke position, and
then back again.
28 – English
Downloaded from www.Manualslib.com manuals search engine
MAINTENANCE
Carburetor Conditions
• Before any adjustments are made the air filter should be
Your Jonsered product has been designed and manufactured to clean and the cylinder cowling fitted. Adjusting the carburetor
specifications that reduce harmful emissions. while a dirty air filter is in use will result in a leaner mixture
After your unit has been run 8-10 tanks of fuel the engine has when the filter is finally cleaned. This can give rise to serious
broken in. To ensure that your unit is at peak performance and engine damage.
producing the least amount of harmful emissions after break in, • Carefully turn the L and H needle to the mid point.
have your authorized servicing dealer, who has a revolution • Do not attempt to adjust the needles beyond the stops as
counter at his disposal, to adjust your carburetor for optimum damage can occur.
operating conditions. • Now start the saw according to the starting instructions and
run it warm for 10 minutes.
Functioning, Basic setting, Final setting NOTE! If the chain rotates the T screw should be turned
!
counter-clockwise until the chain stops.
WARNING! Do not start the saw without the • Place the saw on a flat surface so that the bar points away
bar, chain and clutch cover (chain brake) from you and so that the bar and chain do not come into
assembled. If you do, the clutch might come contact with the surface or other objects.
loose and cause severe injuries.
!
T = Adjustment screw for
idling. Contact your servicing dealer, if the idle speed
setting cannot be adjusted so that the chain
stops. Do not use the saw until it has been
properly adjusted or repaired.
English – 29
Downloaded from www.Manualslib.com manuals search engine
MAINTENANCE
Starter device Tensioning the recoil spring
• Lift the starter cord up in the
! WARNING!
30 – English
Downloaded from www.Manualslib.com manuals search engine
MAINTENANCE
Air filter Muffler
The air filter must be regularly cleaned from dust and dirt in
order to avoid:
• Carburetor malfunctions
• Starting problems
• Engine power reduction The muffler is designed in
• Unnecessary wear on order to reduce the noise level
the engine parts and to direct the exhaust
• Abnormal fuel consumption gases away from the operator.
The exhaust gases are hot
and can contain sparks, which
may cause fire if directed
against dry and combustible
Clean the air filter daily or material. Some mufflers are
more often if the air is equipped with a special
exceptionally dusty in the screen. If your saw has this
working area. type of muffler, you should
clean the screen at least once
• Disassemble the air filter by a week. This is done with a
removing the cylinder cover wire brush.
and unscrew the filter.
When reassembling, make CAUTION! The screen must be replaced, if damaged. The
sure that the filter is tight saw will be overheated, if the screen is clogged. This
against the filter holder. results in damage on the cylinder and the piston. Never use
Clean the filter by brushing a saw with a clogged or defective muffler.
or shaking it.
English – 31
Downloaded from www.Manualslib.com manuals search engine
MAINTENANCE
Cooling system Winter use
During winter time, powder snow and cold weather can cause
running problems, such as:
1. Air intake on the starter • Partly reduce the air inlet of the starter and by doing that
unit. increase the engine temperature.
2. Air guide plate. • Preheat the intake air to the carburetor by removing the
special plug between the cylinder and the carburetor space.
3. Fan blades on the
flywheel.
IMPORTANT! In order to
keep the function of the
centrifugal cleaning, a
continous maintenance and
care must be made.
32 – English
Downloaded from www.Manualslib.com manuals search engine
MAINTENANCE
Below you will find some general maintenance instructions. Weekly maintenance
If you have more questions, contact your servicing dealer.
1. Check that the AV 1
elements are not soft or
Daily maintenance torn.
2
1. Check the throttle trigger 2. Lubricate the clutch drum
for smooth operation. If bearing.
any binding occurs, or if 1 3
engine fails to return to 3. File off burrs, if any, on
idle, the saw should be the sides of the bar.
taken to your dealer, 4. Clean the spark plug and
before it is used again. check the gap.
Also, be sure that the The correct gap is 0,5 mm 4 0,5 mm
trigger cannot be pulled (0,020 inch).
until the throttle trigger 2
lockout is depressed. 5. Check the starter and the
recoil spring. Clean the
2. Clean the chain brake fins on the flywheel. 5
and check its function
according to the 6. Clean the cooling fins on
instructions. Make sure the cylinder.
that the chain catcher is
undamaged. Otherwise 7. Clean or change the 6
replace it immediately. screen in the muffler.
3. Clean or replace the air
3 7
8. Clean the carburetor body
filter as necessary. Check and air box.
for damage or holes.
English – 33
Downloaded from www.Manualslib.com manuals search engine
TECHNICAL DATA
2054
Recommended original and replacement bar
Engine
Cylinder volume, cu.in/cm 3
3,0/49 and chain combinations
Cylinder bore, inch/mm 1,73/44 Following is a list of recommended cutting equipment for
Stroke, inch/mm 1,26/32 the Jonsered chain saw model 2054. The combinations of
Idle speed, rpm 2 600 power head, bar and chain have been investigated in
Power, kW/ rpm 2,2/ 9 600 accordance with the kickback and vibration requirements of
ANSI B 175.1–1991.
Ignition system
Manufacture Electrolux The guide bar nose radius is determined by either the
Type of ignition system ET maximum number of teeth in the nose sprocket or the
Spark plug Champion corresponding maximum nose radius of a solid bar.
RCJ 7Y The following list is the chain saw manufacturers
Electrode gap, inch/mm 0,020/0,5 recommendations. There may be other combinations
available, which will also achieve kickback protection.
Fuel and lubrication
As we are listing the maximum guide bar nose radius, you
system may use a guide bar with smaller nose radius than in our
Manufacturer Walbro list. For guide bars of the same length, all sprocket-nose
Carburetor type HDA 143 guide bars of the same pitch and having the same number
Fuel capacity, US pint/litre 1,18/0,56 of sprocket teeth may be considered to have equivalent
Oil pump capacity at kickback energy. A hard nose bar having the same length
8500 rpm, ml/min 4,25-8,5 and nose radius as a sprocket-bar may be considered to
Oil capacity, US pint/litre 0,80/0,38 have equivalent or less kickback energy than the sprocket-
Type of oil pump Automatic nose bar.
Weight Low kickback saw chain is a chain which has only met the
Without bar and chain, Lbs/kg 11,5/5,2 kickback performance requirements of ANSI B 175.1 safety
requirements for gasoline powered chain saws when tested
Chain/bar on the representative sample of chain saws below 3.8 cu.
Recommended bar lengths, in. specified in ANSI 175.1. We recommend that you as a
inches/cm 13-18"/33-48 replacement use the listed chains or "Low kickback saw
Usable cutting length inches/cm 12-17"/30-43 chains" which are available at your dealer.
Chain speed at max. power,
m/sec 18,6 Guide bar Saw chain
Pitch, inches 0,325"/ 3/8" Length Pitch Max nose
Thickness of drive link, inch inch radius
inch/mm 0,050"/1,3 15 0,325 10T Jonsered S25 / S24 / S21 or
0,058"/1,5 16 0,325 10T Oregon 21VB / 34LG / 21LP or
Number of teeth on drive 18 0,325 10T Total/Sabre 528PS
sprocket 7
15 3/8 11T Jonsered S42 or Oregon 73VL
16 3/8 11T
18 3/8 11T
15 3/8 11T Total/Sabre 988PC
16 3/8 11T
Note: For the chains above you are free to choose between 0,050" and
0,058" gauge drive link for the corresponding bar, see the table below.
34 – English ´*xm[¶5M¨
Downloaded from www.Manualslib.com manuals search engine
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
English – 35
Downloaded from www.Manualslib.com manuals search engine
108 87 75-95
´*xm[¶5M¨ 1998W48
Downloaded from www.Manualslib.com manuals search engine