Professional Documents
Culture Documents
Vacuum level is below the minimum required, for the Ensure the table is sufficiently sealed to maintain
configured time duration, to move the conveyor when the the required vacuum level. Use diagnostics to
8 5 Table vacuum too low to move conveyor.
vacuum system is on. Table is not sufficiently sealed, ensure the vacuum system is functioning properly.
vacuum is off or vacuum is malfunctioning. Repair as needed and resume interrupted function.
Vacuum level is below the minimum required, for the Ensure the table is sufficiently sealed to maintain
configured time duration, to cut material when the vacuum the required vacuum level. Use diagnostics to
9 3 Table vacuum too low cut.
system is on. Table is not sufficiently sealed, vacuum is off or ensure the vacuum system is functioning properly.
vacuum is malfunctioning. Repair as needed and resume interrupted function.
Vacuum level is above the maximum allowed, for the Use diagnostics to ensure the vacuum system is
10 5 Table vacuum too high to convey. configured time duration, to move the conveyor when the functioning properly. Repair as needed and resume
vacuum system is on. interrupted function.
Use diagnostics to ensure proper operation of the
Knife Intelligence sesnsor. Verify straightness of
11 1 Knife Intelligence Sensor Failure on {0}. Due to broken wire(s), sensor failure, or bent knife.
knife. Repair as needed and resume interrupted
function.
Use diagnostics to ensure proper operation of the
Knife Intelligence sesnsor. Verify straightness of
12 1 Knife Intelligence Calibration Failure. Due to broken wire(s), sensor failure, or bent knife.
knife. Repair as needed and resume interrupted
function.
The head was commanded to move outside of the allowed
Commanded position for axis {0} is outside the range for the origin tool as a result of checking fabric width. The job may still process OK, try resuming cutting.
13 2
valid range. This may occur on jobs that are very close to the max width Reduce job width if problem persists.
of the table.
Controller has determined that two beams would have
Collision between beam {0} and beam {1}
14 1 collided if the system was not stopped. This is considered to Report as a software bug.
imminent.
be a flaw in planning.
Some conveyors have poor position control. It is possible for
Jog the conveyor in reverse until the parts are
the conveyor to over or under shoot the desired position. If
reachable by their assigned tools. When moving the
15 3 Conveyor moved too far. the conveyor moved too far one or more process items
conveyor backwards be careful to move conveyor
could be positioned outside their assigned work areas and
forward again to eliminate slack.
cannot be processed.
The operator is required to calibrate (also know as null)
16 5 Knife Intelligence not calibrated. Perform the knife intelligence calibration.
knife intelligence before cutting begins.
Attempt to move an axis to a position before it has been
17 5 Axis {0} is not homed. Initiate the homing sequence.
homed.
A tool was expected to be on and is not. This could be
Use diagnostics to ensure the tool motor is
because the operator did not turn the tool on or a hardware
18 5 Tool {0} is off. functioning properly. Repair as needed and resume
failure is preventing the tool motor from running. Examples
interrupted function.
of such tools are recipricating knives and spinning drills.
19 4 Table vacuum off. The table vacuum must be on in automatic mode. Turn on the vacuum.
Use diagnostics to ensure proper operation of the
The tool pressure failed to reach the commanded pressure
20 3 Failed to set pressure for tool {0}. tool pressure system and sensor. Repair as needed
within the configured timeout.
and resume interrupted function.
21 1 Drive Faulted {0}. FSR: {1} ESR: {2} The drive detected a fault. Re-enable Servos.
22 3 Drive {0} did not enable - Error Register Value 0x{1} The drive failed to enable. Re-enable Servos.
23 5 Can not trim cut with selected tool {0}. A tool that can not cut was selected to trim cut. Selected a tool that has cutting capabilities.
24 5 Trim cut failed to complete. Trim cut failed. Retry trim cut.
Cut engine {0} failed to pause within the expected
25 1 The cut engine failed to pause. Report as a software bug.
amount of time.
Some conveyors have poor position control. It is possible for
the conveyor to over or under shoot the desired position. If
Jog the conveyor forward until the parts are
26 3 Conveyor stopped too soon. the conveyor did not move far enough one or more process
reachable by their assigned tools.
items could be positioned outside their assigned work areas
and cannot be processed.
27 1 Cannot find tool {0}. A tool with the specified device Id can not be found. Restart the system.
The conveyor has failed to move or the operator paused Manually move the conveyor so that the process
28 3 Process item not in its assigned work area.
cutting, moved the conveyor, and resumed cutting. item can be reached by its assigned tool.
AdsSyncWriteReqEx Failed in SetMasterState with
29 1 Error setting Master EtherCAT state. TBD
error code {0}.
AdsSyncWriteReqEx Failed in SetSlaveState with
30 1 Error setting Slave EtherCAT state. TBD
error code {0}.
31 1 Equipment Factory cannot create device "{0}" Error creating software representation of a device. TBD
32 1 Device Node Factory cannot create device "{0}" Error creating software representation of a device. TBD
A Channel does not exist for Connection {0}.
33 1 TBD TBD
Exception: {1}: {2}.
34 1 Cant find channel {0} TBD TBD
35 5 Command has no completion handler pointer. TBD TBD
36 5 Command has no execution handler. TBD TBD
37 5 Command object is null. TBD TBD
Exception occurred while configuring
38 5 TBD TBD
ControllerComponent: {0} at {1}
39 5 Open failed accepted connection %s disposed. TBD TBD
40 5 {0} TBD TBD
41 5 {0}: {1} TBD TBD
Exception occurred while configuring
42 5 TBD TBD
ConnectionManager: {0} at {1}
43 5 The control panel called {0} is not connected. TBD TBD
44 5 Dequeue() returned {0}. TBD TBD
45 5 Error Occurred sending SDO List for {0} TBD TBD
Error Occurred sending Velocity Loop Output Filter
46 5 TBD TBD
{0}
47 5 Factory not found for the following object {0}. TBD TBD
Failed to convert enum type {0}, value {1} to a
48 5 TBD TBD
string.
49 5 Handshake error. Sent {0}. Received {1} TBD TBD
Invalid Equipment Model configuration file.
50 1 TBD TBD
Abandoning load.
Invalid Device Node configuration file. Abandoning
51 1 TBD TBD
load.
Invalid TwinCat configuration file. Missing Node
52 1 TBD TBD
{0}. Abandoning load.
53 1 Configuration node {0} is missing. TBD TBD
54 5 Configuration value {0} for node {1} is missing. TBD TBD
Device {0} was not found in the parameter registry.
55 5 TBD TBD
All IParameter classes must be registered.
56 5 Publisher Not Found For GetValue Request For {0} TBD TBD
57 5 Read Failure. {0}: {1} TBD TBD
58 5 Exception occurred in read thread: {0}: {1}. TBD TBD
Failed to find relative nest for setting a relative
59 5 TBD TBD
origin.
60 5 Reply received does not match pending command. TBD TBD
61 5 Read Error {0} TBD TBD
62 5 SDO Write Error {0} - SDO 0x{1} {2} TBD TBD
Device "{0}" does not recognize the
63 5 TBD TBD
parameter"{1}".
Maximum x for tool {0} exceeds maximum table x.
64 5 TBD TBD
({1} - {2} is greater than {3})
Maximum y for tool {0} exceeds maximum table y.
65 5 TBD TBD
({1} - {2} is greater than {3})
Minimum x for tool {0} exceeds minimum table x.
66 5 TBD TBD
({1} - {2} is less than {3})
Minimum y for tool {0} exceeds minimum table y.
67 5 TBD TBD
({1} - {2} is less than {3})
68 5 Unable to find a tool associated with device id {0}. TBD TBD
226 1 Tool {0}.{1} is not registered in the Tool Factory. TBD TBD
227 5 Serialization error {0} for command {1} TBD TBD
228 5 No factory registered for command {0} TBD TBD
229 5 No channel defined for this connection: {0} TBD TBD
230 5 Unable to identify connection: {0} TBD TBD
231 5 SocketException: {0} TBD TBD
232 1 Adapter TypeName Not Recognized: {0}. TBD TBD
Cant Subscribe to State Model because service isnt
233 5 TBD TBD
opened.
Unable to correctly assign the device id of Control
234 5 TBD TBD
Parameter [Key:{0}, Value:{1}]
Unable to correctly assign the device id of Control
235 5 TBD TBD
Parameter [Key:{0}, Value:{1}] : {2}
Unable to correctly assign the key of Control
236 5 TBD TBD
Parameter [Key:{0}, Value:{1}]
Unable to correctly assign the key of Control
237 5 TBD TBD
Parameter [Key:{0}, Value:{1}] : {2}
A save was requested for queue item with GUID
238 5 TBD TBD
{0}, but the filename was bad or missing. {1}
239 1 Invalid tool configuration file: {0} TBD TBD
The system is attempting to open a job file that is no longer Open the "Jobs Queue" and inspect the "In
240 1 Unable to locate file: {0} available. The job may have been previously canceled or Progress" queue. Remove or Cancel the job
removed from the Jobs Queue. matching the reported filename.
Unable to locate a tool while sending tool holder
241 5 TBD TBD
information to the controller: {0}
242 5 {0} Path not found. TBD TBD
Unable to fetch current material from database:
243 5 TBD TBD
{0}
Unknown ProcessItem, cannot generate a time
244 1 TBD TBD
estimate for type {0}.
The constant rate conveyor velocity is greater than
245 1 TBD TBD
the maximum velocity for the conveyor.
The specified path plan sequence places a process
246 2 TBD TBD
item beyond the work area.
Timeout occurred attempting to reach idle
247 5 TBD TBD
vacuum.
StatusMonitor: Error threshold triggered on {0}
248 3 TBD TBD
with value {1} exceeding {2} limit {3} : {4}
249 1 Unhandled exception in workflow: {0} An internal software error has occurred Report as a software bug.
250 1 Unknown Error in Biting Workflow. TBD TBD
Timeout occurred while requesting a tool model.
251 5 TBD TBD
Another attempt will be made.
252 5 Unable to connect to database. TBD TBD
253 5 An error ocurred while executing your query. TBD TBD
254 5 The specified global parameter cannot be null. TBD TBD
A global parameter cannot be created without a
255 5 TBD TBD
valid Name field.
A global parameter cannot be created without a
256 5 TBD TBD
valid Value field.
A material parameter already exists with the
257 5 TBD TBD
name: {0}.
An error occurred while submitting to database.
258 5 TBD TBD
The changes have not been made: {0} : {1}
A global parameter cannot be updated without a
259 5 TBD TBD
valid Name field.
A global parameter cannot be updated without a
260 5 TBD TBD
valid Value field.
261 5 The specified global parameter does not exist. TBD TBD
A global parameter already exists with the name:
262 5 TBD TBD
{0}.
263 5 The specified material cannot be null. TBD TBD
A material cannot be created without a valid Name
264 5 TBD TBD
field.
265 5 A material already exists with the name: {0}. TBD TBD
A material cannot be updated without a valid
266 5 TBD TBD
Name field.
267 5 The specified material does not exist. TBD TBD
268 5 The specified material parameter cannot be null. TBD TBD
A material parameter cannot be created without a
269 5 TBD TBD
valid Name field.
A material parameter cannot be created without a
270 5 TBD TBD
valid Value field.
A material parameter cannot be created without a
271 5 TBD TBD
valid material id field.
272 5 The specified material could not be found. TBD TBD
A material parameter cannot be updated without a
273 5 TBD TBD
valid Name field.
A material parameter cannot be updated without a
274 5 TBD TBD
valid Value field.
A material parameter cannot be updated without a
275 5 TBD TBD
valid material id field.
276 5 The specified material parameter does not exist. TBD TBD
277 5 The specified override cannot be null. TBD TBD
An override cannot be created without an
278 5 TBD TBD
associated Control Parameter.
An override already exists for name {0} on this
279 5 TBD TBD
material.
An override cannot be updated without a valid id
280 5 TBD TBD
field.
281 5 The specified override does not exist. TBD TBD
The control parameter for the specified override
282 5 TBD TBD
does not exist.
An override cannot be deleted without a valid id
283 5 TBD TBD
field.
Database does not exist. Cannot update job
284 1 TBD TBD
instance.
Database does not exist. Cannot retrieve job
285 1 TBD TBD
instances.
Database does not exist. Cannot clone job
286 1 TBD TBD
instance.
Database does not exist. Cannot delete job
287 1 TBD TBD
instance.
288 5 Failed to clone a job instance. Exception: {0}. TBD TBD
289 5 Failed to delete a job instance. Exception: {0}. TBD TBD
290 5 Failed to update a job instance. Exception: {0}. TBD TBD
291 5 Unable to configure Tools, null tools parameter. TBD TBD
Unable to configure ToolHolders, null toolholders
292 5 TBD TBD
parameter.
294 5 The tool type cannot be null. TBD TBD
295 5 The tool name cannot be null. TBD TBD
296 5 Tool wear cannot be less than zero. TBD TBD
This tool name and type combination already
297 5 TBD TBD
exists in the database. Tool: {0}.{1}.
298 5 Unable to locate the specified tool in the database. TBD TBD
299 5 Cannot change a tool without a tool holder. TBD TBD
Tool change not reflected in the database. Unable
300 5 to find installed tool in the database. ToolHolder: TBD TBD
{0}.{1}, Tool: {2}.{3}.
Unable to locate the specified tool in database, the
301 5 TBD TBD
id field is missing.
Tool change not reflected in the database. Unable
302 5 to find tool holder in the database. ToolHolder: TBD TBD
{0}.{1}.
303 5 Cannot remove a tool without a tool holder. TBD TBD
Tool removal not reflected in the database. Unable
304 5 to find tool holder in the database. ToolHolder: TBD TBD
{0}.{1}.
305 5 Job instance information cannot be null. TBD TBD
306 5 Tool holder mapping cannot be null. TBD TBD
307 5 Job instance database id cannot be null or empty. TBD TBD
A job instance does not exist for the specified
308 5 TBD TBD
database id.
ToolHolder Mapping - unable to locate a tool
309 5 TBD TBD
within the tool model.
Unable to configure ToolHolder: {0}, a configured
310 5 tool does not exist in the ToolModel with a TBD TBD
matching id.
Unable to parse string {0}, using stored value of {1}
311 5 TBD TBD
seconds.
Calibration Factory cannot create calibration Error creating software representation of a calibration
312 1 TBD
strategy "{0}" strategy.
Invalid Calibration configuration file. Abandoning
313 1 TBD TBD
load.
314 4 The knife enable switch on {0} is not on. The knife enable switch is off. Turn the knife enable switch on.
315 3 The knife drive amplifier on {0} is disabled. The knife drive is disabled. Disable and re-enable servos.
The knife drive amplifier on {0} is not at the
316 3 The knife motor may be damaged. Check the knife motor.
required velocity.
Exception during begin fetch remote side
317 5 TBD TBD
operation state \"{0}\"
Database does not exist. Cannot retrieve process
318 1 TBD TBD
item.
Database does not exist. Cannot delete process
319 5 TBD TBD
item.
320 5 Failed to delete a process item. Exception: {0}. TBD TBD
321 5 Failed to update a process item. Exception: {0}. TBD TBD
Database does not exist. Cannot update active
322 5 TBD TBD
nest.
Database does not exist. Cannot retrieve active
323 5 TBD TBD
nest.
324 1 Database does not exist. Cannot delete active nest. TBD TBD
325 1 Failed to delete a active nest. Exception: {0}. TBD TBD
326 5 Failed to update a active nest. Exception: {0}. TBD TBD
Database does not exist. Cannot update process
327 5 TBD TBD
item.
328 5 Job instance Id or nest id cannot be empty or null. TBD TBD
415 5 A Material Export SQL Exception occurred: {0} - {1} TBD TBD
A Material Export General Exception occurred: {0} -
416 5 TBD TBD
{1}
A Material Import Serialization Exception occurred:
417 5 TBD TBD
{0} - {1}
418 5 A Material Import IO Exception occurred: {0} - {1} TBD TBD
419 5 A Material Import SQL Exception occurred: {0} - {1} TBD TBD
A Material Import General Exception occurred: {0} -
420 5 TBD TBD
{1}
421 5 Material Import non-Exception error: {0} TBD TBD
422 5 Material Export non-Exception error: {0} TBD TBD
Exception thrown by JobSerializer.DeserializeFromFile(string
423 5 IO Exception reading file: {0} Ignore
file)
424 5 The tool in {0} cannot perform a trim cut. The tool is not a cutting tool. Put a cutting tool in the holder specified.
The specified JOB requires a velocity below the
425 5 TBD TBD
fixed rate velocity in order to be processed.
426 1 Unknown Error in Continuous Workflow. TBD TBD
There was an erroneous position command generated for Re-enable servos and try to continue. Try to
The delta commanded position ({0}) for axis {1} is
427 2 the axis. This could be due to an bug in the contour builder determine if the error is repeatable with the same
outside the valid range.
or related to the job file being cut. job file. Report as a software bug.