Professional Documents
Culture Documents
Table of Contents
Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Author:spiderham
I love making random stuff. The more intricate, the more intrigued I am. I jump from project to project without rhyme or reason so finishing is a challenge, my
wife calls it project ADD. My current interests are in prop making and animatronics... I got some stuff in the works so say tuned...
Materials:
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Step 2: The hard part- Drilling holes in round rod
Don't cut anything to size yet, you can minimize waste.
To align the chuck on the press to the vice you"ll 1st have to chuck the rod to be drilled on the press. Once done, Bring the vice to the rod and close it onto the chucked
rod without moving the rod. Finally, clamp the vice down carefully so it doesn't move on you. You'll have to repeat this step for every piece to ensure that you're drilling
centered.
Using the 7/64" drill bit, set up and drill a hole about a 1/4" from the end of the all thread piece. It might help to file a small flat where the hole will start on the all thread.
Reset the clamp, and using the same bit, drill about an inch from the end of the center punch or the 3/8" rod. Start drilling very slowly and watch the bit when it touches
the workpiece, make sure the bit doesn't move to either side.
If you decide to make your own wing nut, drill a 13/64" hole an inch from the end of the rod in the same way as the other two pieces.
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes Image Notes
1. Repeat this step for every rod to be drilled. 1. Piece of the brass punch that I made my wing nut from.
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes
1. 3/8" ss rod. If you use a center punch, you won't need this rod but you'll still
have to drill this hole on the punch.
Once the slot is finished, cut the other end to 1/2" from the end of the slot and clean and de-burr all of the edges.
Image Notes
1. It's hard to see, but there's a score mark that's mirrored on the opposite side od
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
the tube.
2. It's hard to see, but there's a score mark that's mirrored on the other side of the
tube.
Image Notes
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
1. I've highlighted the score mark for ease of cutting.
Image Notes
1. A little tape for grip.
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes Image Notes
1. Try not to go past your marks. You can easily work the ends with a file. 1. These wavy marks are from the tapered rat tail file from a jeweler's file set. I
chucked it on my drill and drilled it through side by side to remove some bulk.
Image Notes
1. Nice and clean! :)
2. Nice and clean. :)
To make the nose piece, I chucked the rod on the drill and filed a shoulder where the taper ends. Using a file and some elbow grease, I turned the shoulder down so that
it was about 3/100s of a mm larger than the opening on the body of the tool. I constantly checked my work and made sure it was parallel across at least a half inch off the
shoulder. Once I was close to the desired measurement, I finished the shoulder with some sandpaper to get a smooth finish.
Once happy with the shape, I moved the piece into the chuck so that 9/16" of the shoulder was exposed. I then used a hacksaw against the chuck with the drill at low
speed and cut the nose piece off cleanly so that I ended up with a half inch shoulder. To make assembly a little easier, I slightly chamfered the end on the shoulder and
filed the tip left from cutting.
I used a file and sandpaper to shape the tapered end of my nose piece before making the shoulder, but it took allot of work which is why I suggest using an old center
punch. For my original tool, I used an old 1/2" pin I found in a scrap pile. It ended up dictating the size of the tool which i thought to be too big for my needs.
I used the same method to shape the brass wing nut. If you're not interested in looks or want something easier, try your local hardware store for a regular wing nut.
They're inexpensive and easy to find.
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes
1. Try to keep this shoulder as clean as possible.
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes
1. This took some serious elbow grease, but I'm happy with the end result. :D
Image Notes
1. Start the drill slow to keep the hacksaw from wandering.
Next, sand down 4" of the 1/8" rod to 2.9mm and cut two 2" pieces. Starting with the all thread, drive your pin into the hole through the slot as shown in the picture until
both side are even. The assembly should slide freely all the way through the slot. If not. pull the all thread all the way up to the top of the slot and gradually rework the it
until you get a clean glide. Install the nose piece pin. If the pins are a little loose, use a little super glue on both sides of the pin.
On the tip of the nose, you need a small notch for the wire to cradle in while you're pulling it tight. A small triangle file makes short work of this. Just keep the notch
parallel with your pins and centered on the tip. I made mine about 1/8" deep.
Finally, install the washer and the wing nut, bottom out the tool and cut the all thread to 1/2" above the wing nut.
Done! Go make some wire clamps. For instructions on how to use the tool, check out GeeDeeKay's instructable, http://www.instructables.com/id/Hose-Clamp-
Magic/?ALLSTEPS. It was the inspiration for my instructable.
Image Notes
1. I used the pin and the drill bit to help align the pieces when pressing.
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes
1. Wing nut
2. 1/8" pins
3. All tread
4. Tool body
5. UHMW washer
6. Nose piece
7. All of the parts ready for assembly.
Image Notes
1. Tap-tap-tap!
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes
1. Start with a couple light scores and check for centering and alignment.
Image Notes
1. Leave about 1/2" of extra all thread at the top. Just remember to have the tool
bottomed out.
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes
1. Done!
http://www.instructables.com/id/Wire-clamping-tool-DIY-/
Image Notes
1. My first build. About 10" long.
Related Instructables
Coat Hanger
Poor Man's Helping Hands The Extension
Improving a Track Lighting cord from Hell
Hose Clamp Welder Ground Clamp Lamp by Brennn10
by randofo by neosenshi
Magic by Clamp by Phil B Wifi Extender by
GeeDeeKay FullyInvolvedScientist
Comments
1 comments Add Comment
http://www.instructables.com/id/Wire-clamping-tool-DIY-/