Professional Documents
Culture Documents
i s
j
2 b k r
q
h l
c g p
d
m o
e n
f
1 2 3
Place the base of the cleaner so it To secure the body in place insert Pull back the flap on the clear
is facing away from you. one of the screws supplied into the window. Match the slots on the
Position the body so that the lower back of the cleaner, through the hose to the tabs on the hose inlet.
hose is on your right hand side. hole located above the on/off pedal. Push down firmly on the cuff and
Push the body down into place. turn anti-clockwise to lock in place.
Putting your vacuum cleaner together
4 5 6
Align the holes in the tool holder, Use two of the screws supplied to With the hose clip on the handle
with the holes on top of the body. secure the tool holder in place. facing you place it onto the top of
Do not over tighten. the body of the cleaner.
7 8 9
Push down firmly and line up the Use one of the screws supplied to Insert the small end of the main
screw hole on the rear of the handle. secure the handle on the body. hose into the tool holder on the
right hand side.
Putting your vacuum cleaner together
10 11 12
Using the handle attach the main Push the canister lid firmly on top of Attach the tools to the tool holder.
hose into the left hand side of the the dust canister and place it onto The 2 in 1 tool fits over a post at
cleaner. Press down firmly to the cleaner. The canister lid will the back of the vacuum cleaner.
secure in place. The main hose can snap into place in the body of the The crevice tool fits into a round
then be secured in the top and side cleaner. slot on the rear right hand side of
of the tool holder. the tool holder. The extension wand
hose on the left hand side.
1 2 3
7
C
Plug the cord into an electrical To unlock the handle from the Move the handle to the desired
outlet and turn on by pressing the upright position press the handle position (A) for storage and position
on/off pedal, located on the back release pedal down. (B) for normal operation.
left of the cleaner. To clean under furniture, press
the release pedal again and use
position (C).
Operating the vacuum cleaner Cleaning upholstery
1 2 3
Make sure the vacuum cleaner has Remove the hose from the tool Slide the hose into the lower hose
been switched off and is in an Holder. with the tab facing upwards twist
upright position. Remove the lower together to secure.
hose by twisting clockwise and
pulling away from the base of the
cleaner.
4 5 6
For hard to reach area’s when Choose the accessory that suits When moving from one room to
additional hose length is required, your need or use the hose alone. another use the carrying handle at
use the extension wand. It fits over To fit the attachments push them the rear of the vacuum cleaner.
the end of the hose handle. firmly on to the end of the extension
wand or hose handle. To remove
the tool, twist and pull apart gently.
Emptying the dust canister
1 2 3
10
Make sure the vacuum To remove the lid of the dust Empty the all the dust and dirt from
cleaner has been switched off and canister hold the top and the side the dust canister.
unplugged from the mains supply. handles firmly and turn the lid
To remove the dust canister from anti-clockwise. Pull the lid away
the vacuum cleaner press the from the body of the dust canister.
release catch and pull it forward.
4 5 6
11
The filter inside the dust canister Twist and pull the filter out. Replace the filter into the dust
should not need replacing but it To clean it, tap it gently against the canister. Push it firmly into place to
should be cleaned each time the side of a dustbin. Do not use a prevent dust and dirt leaking out.
dust canister is emptied. Remove it brush to clean it as this may Replace the canister lid turning
by grasping the ring at the top of damage the filter. Do not wash the clockwise and return the dust
the filter. filter. canister to the body of the vacuum
cleaner
Belt or Brush removal and replacement Phillips screwdriver required
1 2 3
12
nozzle guard
tabs
Unplug the vacuum cleaner from Lift and remove the brush bar, then The belt should sit on the end of the
the mains supply. Press the handle slide the belt off the motor shaft brush bar with no bristles against
release button and turn the vacuum and dispose of it. the end cap. Re-fit the brush bar.
cleaner over so that the base lies Place a new belt on the motor shaft Ensure the end caps are in the
flat and face up. Use a screwdriver and then slip the brush bar through correct position. Rotate the brush
to remove the four retaining screws the belt. bar to check the belt is not twisted.
shown above. Replace the nozzle guard.
Remove the nozzle guard. Align the tabs and re-fit the screws.
Troubleshooting
Vacuum won’t pick up/ • Lower hose not connected properly. • Refer to page 3 for fitting information.
loss of suction • Dust canister not installed correctly or full. • See ‘Emptying the dust canister’.
• Broken or worn belt. • Replace the belt.
• Clogged filter. • Remove filter and clean.
• Nozzle/hose or hose inlet is clogged. • Remove nozzle/hose and remove
For further information in the UK, call the VAX HELPLINE : 0870 606 1248
Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK. For your nearest Service Agent please call VAX Care.
Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate.
UK SERVICE & HELP - VAX CARE 0870 6061248
VS 18 / VS 19 Easy Guide
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: VAX Limited, hereby on our own responsibility declare that the products: VS 18 & VS 19 are manufactured in compliance with the following;
Safety: 72/23/EEC Low Voltage Directive as modified by 93/68/EEC
EMC: 89/336/EEC Electromagnetic compatibility Directive as modified by 93/68/EEC
VAX Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK.
email: enquiry@vax.co.uk - website: www.vax.co.uk
Version 1