Professional Documents
Culture Documents
Recommended Spreading Rate per coat: Test Name Test Method Results
Minimum Maximum ASTM D4060, CS17
Abrasion Resistance
Wet mils (microns) 2.5 (63) 4.0 (100) wheel, 1000 cycles, 103 mg loss
(DTM)
Dry mils (microns) 1.5 (38) 2.5 (63) 1 kg load
~Coverage sq ft/gal (m2/L) 384 (9.4) 640 (15.7) Accelerated Weath- ASTM D4587,
91% gloss retention
Theoretical coverage sq ft/gal ering -QUV-A QUV-A, 4,000 hours
(m2/L) @ 1 mil / 25 microns dft 962 (23.7)
Adhesion ASTM D4541 1,053 psi
NOTE: Brush or roll application may require multiple coats to Excellent: Acids,
achieve maximum film thickness and uniformity of appearance. Chemical Spot Re- Water
ASTM D2794
sistance Good: Alkalies, Alco-
Drying Schedule @ 4.0 mils (100 microns): hols, Fuels
@ 40oF/4.5oC @ 77oF/25oC @ 100oF/37oC Rating 10 per ASTM
Corrosion Weather- ASTM D5894, 10 D714 for blistering.
50% RH
ing cycles, 3,360 hours Ratings 10 per ASTM
To touch: 2 hours 1 hour 30 minutes D610 for rusting.
To handle: 24 hours 18 hours 16 hours Direct Impact Resis-
To recoat: ASTM D2794 60 in. lbs.
tance
Min 5 hours 2 hours 1 hour Dry Heat Resistance ASTM D2485 250oF (121oC)
Max Unlimited Unlimited Unlimited
ASTM D522, 180o
To cure: 28 days 14 days 10 days Flexibility Passes
bend, 1/8" mandrel
Drying time is temperature, humidity, and film thickness dependent.
Rating 10 per ASTM
Shelf Life: 12 months, unopened ASTM D4585, 2,000 D714 for blistering.
Humidity Resistance
Store indoors at 40°F (4.5oC) to hours Ratings 10 per ASTM
100°F (38oC). D610 for rusting.
(Tinted colors must be used
within 7 days after tinting) Pencil Hardness ASTM D3363 4B
Flash Point: >105°F (40.6oC), Seta Flash
Reduction:
Spray and Brush: R6KH26, 10%, required
Roller: R7K323, 1%, required
Clean Up: R6KH26 or Xylene, R2K4
ORDERING INFORMATION
Packaging: 1 gallon (3.78L) and 5 gallon (18.9L)
containers
Weight: B80W901 10.51 ± 0.2 lb/gl 1.26 Kg/L
B80T904 9.42 ± 0.2 lb/gl 1.13 Kg/L
SAFETY PRECAUTIONS
Refer to the MSDS sheet before use.
Published technical data and instructions are subject to change without notice.
Contact your Sherwin-Williams representative for additional technical data and
The systems listed above are representative of the product's use, instructions.
other systems may be appropriate.
WARRANTY
The Sherwin-Williams Company warrants our products to be free of manufactur-
DISCLAIMER ing defects in accord with applicable Sherwin-Williams quality control procedures.
The information and recommendations set forth in this Product Data Sheet are Liability for products proven defective, if any, is limited to replacement of the defec-
based upon tests conducted by or on behalf of The Sherwin-Williams Company. tive product or the refund of the purchase price paid for the defective product as
Such information and recommendations set forth herein are subject to change and determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
pertain to the product offered at the time of publication. Consult your Sherwin- OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
Williams representative to obtain the most recent Product Data Information and STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
Application Bulletin. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
www.sherwin-williams.com/protective
Protective POLYSILOXANE 1K
& ACRYLIC SILOXANE
Marine B80B900 BLACK B80W901 EXTRA WHITE BASE
Coatings B80R900 SAFETY RED
B80Y900 SAFETY YELLOW
B80T904 ULTRADEEP BASE
Surface must be clean, dry, and in sound condition. Remove all Temperature: 40°F (4.5°C) minimum, 120°F (49°C)
oil, dust, grease, dirt, loose rust, and other foreign material to maximum
ensure adequate adhesion. (air, surface, and material)
At least 5°F (2.8°C) above dew point
Iron & Steel, Atmospheric Service: Relative humidity: 40% minimum, 85% maximum
Minimum surface preparation is Hand Tool Clean per SSPC-SP2.
Remove all oil and grease from surface by Solvent Cleaning per APPLICATION EQUIPMENT
SSPC-SP1. For better performance, use Commercial Blast Clean-
ing per SSPC-SP6/NACE 3, blast clean all surfaces using a sharp,
angular abrasive for optimum surface profile (2 mils). Prime any The following is a guide. Changes in pressures and tip sizes may
bare steel within 8 hours or before flash rusting occurs. be needed for proper spray characteristics. Always purge spray
equipment before use with listed reducer. Any reduction must be
Aluminum: compliant with existing VOC regulations and compatible with the
Remove all oil, grease, dirt, oxide and other foreign material by existing environmental and application conditions.
Solvent Cleaning per SSPC-SP1.
Clean Up ..........................R6KH26 or Xylene, R2K4
Galvanized Steel:
Allow to weather a minimum of six months prior to coating. Solvent
Airless Spray
Clean per SSPC-SP1. When weathering is not possible, or the
surface has been treated with chromates or silicates, first Solvent Unit.................................30:1 pump
Clean per SSPC-SP1 and apply a test patch. Allow paint to dry at Pressure.........................3000-3300 psi
least one week before testing adhesion. If adhesion is poor, brush Hose...............................3/8" ID
blasting per SSPC-SP7 is necessary to remove these treatments. Tip ...................................017" - .021"
Rusty galvanizing requires a minimum of Hand Tool Cleaning per Filter ...............................60 mesh
SSPC-SP2, prime the area the same day as cleaned. Reduction .......................10% R6KH26, required
SAFETY PRECAUTIONS
Refer to the MSDS sheet before use.
Published technical data and instructions are subject to change without notice.
CLEAN UP INSTRUCTIONS Contact your Sherwin-Williams representative for additional technical data and
Clean spills and spatters immediately with Xylene, R2K4. Clean instructions.
tools immediately after use with Xylene, R2K4. Follow manufac-
turer's safety recommendations when using any solvent. WARRANTY
The Sherwin-Williams Company warrants our products to be free of manufacturing
DISCLAIMER defects in accord with applicable Sherwin-Williams quality control procedures.
The information and recommendations set forth in this Product Data Sheet are Liability for products proven defective, if any, is limited to replacement of the de-
based upon tests conducted by or on behalf of The Sherwin-Williams Company. fective product or the refund of the purchase price paid for the defective product
Such information and recommendations set forth herein are subject to change and as determined by Sherwin-Williams. NO OTHER WARRANTY OR GUARANTEE
pertain to the product offered at the time of publication. Consult your Sherwin- OF ANY KIND IS MADE BY SHERWIN-WILLIAMS, EXPRESSED OR IMPLIED,
Williams representative to obtain the most recent Product Data Information and STATUTORY, BY OPERATION OF LAW OR OTHERWISE, INCLUDING MER-
Application Bulletin. CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
www.sherwin-williams.com/protective