Professional Documents
Culture Documents
DESCRIPTION
TX-2C TX-2CS
RX-2C RX-2CS
FEATURES
BLOCK DIAGRAM
FOSC TEST B
13 2
OSCI 12
Oscillator Timing
Generator
OSCO 11
9 VDD
RIGHT 1
LEFT 14
10 PC
Latch Encoding
TURBO 6 Logic 8 SO
Circuit Circuit
7 SC
FORWARD 5
BACKWARD 4
3
GND
OSCI 4
Timing
Oscillator generator 13 VDD
OSCO 5
Decoding Counter
SI 3 AMP circuit
6 RIGHT
LX 8 DC-DC
7 LEFT
latch 12 TURBO
VO2 1 10 BACKWARD
VI2 16 11 FORWARD
2
GND
ELECTRICAL CHARACTERISTICS
2. RX-2 (VDD=4.0V, Fosc=128KHz, Tamb=25°C, DC-DC is not used, unless otherwise specified.)
Characteristics Symbol Min. Typ. Max. Unit
Operating Voltage VDD 1.8 4.5 5.0 V
Operating Current IDD -- -- 1.0 mA
Driving Current Idrive 4.5 -- -- mA
Tolerance of frequency Ftolerance -20 +20 %
PIN CONFIGURATION
PIN DESCRIPTION
1. TX-2C
Pin No. Symbol Description
1 RIGHT The rightward function will be selected, if this pin is connected to GND
2 NC Not connect
3 GND Negative power supply
4 BACKWARD The backward function will be selected, if this pin is connected to GND
5 FORWARD The forward function will be selected, if this pin is connected to GND
6 TURBO The turbo function will be selected if this pin is connected to GND
7 SC Output pin of the encoding signal with carrier frequency
8 SO Output pin of the encoding signal without carrier frequency
9 VDD Positive power supply
10 PC Power control output pin
11 OSCO Oscillator output pin
12 OSCI Oscillator input pin
13 NC Not connect
14 LEFT The leftward function will be selected, if this pin is connected to GND
2. RX-2C
Pin No. Symbol Description
1 VO2 Inverter 2 output pin for power amplify
2 GND Negative power supply
3 SI Input pin of the encoding signal
4 OSCI Oscillator input pin
5 OSCO Oscillator output pin
6 RIGHT Rightward output pin
7 LEFT Leftward output pin
8 LX DC-DC output pin
Output pin (pull up) to decide the format of output sign, RX2C is same with
9 MOD
RX2 if the pin is high, and if the pin is low, RX2C output another sign format.
10 BACKWARD Backward output pin
11 FORWARD Forward output pin
12 TURBO TURBO output pin
13 VDD Positive power supply
14 VI1 Inverter 1 input pin for power amplify
15 VO1 Inverter 1 output pin for power amplify
16 VI2 Inverter 2 input pin for power amplify
FUNCTION DESCRIPTION
CODE FORMAT
1. ENCODE RULE
(A).Bit Forma (W1 is used for function codes, W2 for start codes)
1KHz
W1
1KHz 50% Duty cycle
W2
500Hz 75% Duty cycle
(B).DATE FORMAT
W2 W2 W2 W2 (n) X W1 W2 W2 W2 W2 (n) X W1 W2 W2 W2 W2
W2 W2 W2 W2 1 2 3 4 W2 W2 W2 W2
1 2 3 4 W1 W1 W1 W1
W1 W1
n-th
start code
n x W1
function code
1 word
2. ENCODE/DECODE TIMING
(A)
Encode output
1st word 2nd word 3rd word 1 2 3 4 5 6 7 8
end code
Decode output
9ms 9ms
(B)
SI
Decode output
T=17ms+(nW1)x1ms
FUNCTION
Function key TX2C command RX2C,MOD=1 Command(RX2C,MOD=0)
Over code Over code
forward forward Forward pulse 50Hz 50%Duty
Forward and turbo forward Forward and turbo
turbo turbo Forward and turbo
Forward and left
Forward and turbo and left Forward and left
Forward pulse 50Hz 50%Duty
(To be continued)
(Continued)
Function key TX2C command RX2C,MOD=1 Command(RX2C,MOD=0)
Forward and right
Forward and turbo and right Forward and right
Forward pulse (50Hz 50%Duty)
Backward
Backward Backward
Backward pulse 50Hz 50%Duty
Backward and right
Backward and right Backward and right
Backward pulse 50Hz 50%Duty
Backward and left
Backward and left Backward and left
Backward pulse 50Hz 50%Duty
Left Left Left
Right Right Right
Note: when a key is low voltage, it is an input key.
, high voltage format is used when there is no output format.
TEST CIRCUIT
Antenna
C1 68p C3
R2 D2
12p
Q1 R1 1.5K C4 C5 D1 270 IN4148 C6 C7
C1815 104 3.8V
104p 12V
L1 C2
3.3 H 27p L2
9V
Q2
R6
9013
C10 5.6K
C8 R3 R4 C11 R7 Q3
472 560 3K Q5
103 3.3K Q7 R11
9013 R10 8550
C12 150 8550 150
R8 M Q9
104 Q4 9013 Switch
R5 690
9013
C9 4.7M R9 C13 104 R12
104 690 Q6 Q8 690
C15 9013 9013
R13
3K 500p
16 15 14 13 12 11 10 9
C14 R14
30p 4.7M
RX-2C
1 2 3 4 5 6 7 8
R15
1K R20
Q12 Q14 150
R17 8550 8550
R16 R18
220K 100K Q10
3K 9013 M
Q15
R19
690 Q11 Q13 9013
C16 C17 104 R21
202 9013 9013 690
PACKAGE OUTLINE
DIP-14-300-2.54 UNIT: mm
0.25±0.05
6.35±0.25
7.62
4.36MAX
3.00MIN
SOP-14-225-1.27 UNIT: mm
DIP-16-300-2.54 UNIT: mm
SOP-16-225-1.27 UNIT: mm