Professional Documents
Culture Documents
R1283x SERIES
OUTLINE
The R1283x 2ch DC/DC converter is designed for CCD & OLED Display power source. It contains a step up
DC/DC converter and an inverting DC/DC converter to generate two required voltages by CCD & OLED Display.
Step up DC/DC converter generates boosted output voltage up to 20V. Inverting DC/DC converter generates
negative voltage up to VIN voltage minus 20V independently. Start up sequence is internally made. Each of the
R1283x series consists of an oscillator, a PWM control circuit, a voltage reference, error amplifiers, over current
protection circuits, short protection circuits, an under voltage lockout circuit (UVLO), an Nch driver for boost
operation, a Pch driver for inverting. A high efficiency boost and inverting DC/DC converter can be composed
with external inductors, diodes, capacitors, and resistors.
FEATURES
Operating Voltage ......................................... 2.5V to 5.5V
Step Up DC/DC (CH1)
Internal Nch MOSFET Driver (RON=400mTyp.)
Adjustable VOUT Up to 20V with external resistor
Internal Soft start function (Typ. 4.5ms)
Over Current Protection
Maximum Duty Cycle: 91%(Typ.)
Inverting DC/DC (CH2)
Internal Pch MOSFET Driver (RON=400m Typ.)
Adjustable VOUT Up to Vdd-20V with external resistor
Auto Discharge function for negative output
Internal Soft start function (Typ. 4.5ms)
Over Current Protection
Maximum Duty Cycle: 91%(Typ.)
Short Protection with timer latch function (Typ. 50ms); Short condition for either or both two outputs makes
all output drivers off and latches./ If the maximum duty cycle continues for a certain time, these output
drivers will be turned off.
CE with start up sequence function
CH1CH2 (R1283K001x) / CH2CH1(R1283K002x) Selectable
UVLO function
Operating Frequency Selection .......... 300kHz / 700kHz / 1400kHz
APPLICATION
Fixed voltage power supply for portable equipment
Fixed voltage power supply for CCD, OLED, LCD
1
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
BLOCK DIAGRAM
VCC
PVCC
UVLO
PWM
Control
LX2
Maxduty
VREF Vref
VFB2 Discharge
Control
Vref
VOUTN
VFB1
Vref
LX1
GND
PWM
Control
Sequence
CE Control
PGND
2
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
SELECTION GUIDE
The start-up sequence, oscillator frequency, and the package for the ICs can be selected at the user’s
request.
3
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
PIN CONFIGURATIONS
WLCSP-11-P2 • DFN(PL)2730-12
Top View Bottom View
Top View Bottom View 12 11 10 9 8 7 7 8 9 10 11 12
3 3
2 2
1 1
A B C D D C B A
1 2 3 4 5 6 6 5 4 3 2 1
PIN DESCRIPTIONS
WLCSP-11-P2
Pin No Symbol Pin Description
A1 PGND Power GND pin
A2 VFB1 Feedback pin for Step up DC/DC
A3 LX1 Switching pin for Step up DC/DC
B1 PVCC Power Input pin
B2 CE Chip Enable pin for the R1283
B3 LX2 Switching pin for Inverting DC/DC
C1 GND Analog GND pin
C3 VOUTN Discharge pin for Negative output
D1 VCC Analog power source Input pin
D2 VREF Reference Voltage Output pin
D3 VFB2 Feedback pin for Inverting DC/DC
• DFN(PL)2730-12
Pin No Symbol Pin Description
1 NC No Connect
2 LX1 Switching pin for Step up DC/DC
3 LX2 Switching pin for Inverting DC/DC
4 VOUTN Discharge pin for Negative Output
5 CE Chip Enable pin for the R1283
6 VFB2 Feedback pin for Inverting DC/DC
7 VREF Reference Voltage Output pin
8 VCC Analog power source Input pin
9 VFB1 Feedback pin for Step up DC/DC
10 GND Analog GND pin
11 PVCC Power Input pin
12 PGND Power GND pin
) Tab is GND level. (They are connected to the reverse side of this IC.)
The tab is better to be connected to the GND, but leaving it open is also acceptable.
4
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the
recommended operating conditions, even if when they are used over such conditions by momentary
electronic noise or surge. And the semiconductor devices may receive serious damage when they continue
to operate over the recommended operating conditions.
5
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
ELECTRICAL CHARACTERISTICS
R1283x Topt25C
Symbol Item Conditions Min. Typ. Max. Unit.
VCC Operating Input Voltage 2.5 5.5 V
VCC=5.5V, FREQ=300kHz 2.0 mA
VCC Consumption Current
ICC1 VCC=5.5V, FREQ=700kHz 4.0 mA
(Switching)
VCC=5.5V, FREQ=1400kHz 8.0 mA
VCC=5.5V, FREQ=300kHz 250 A
VCC Consumption Current
ICC2 VCC=5.5V, FREQ=700kHz 300 A
(At no switching)
VCC=5.5V, FREQ=1400kHz 350 A
Istandby Standby Current VCC=5.5V 0.1 3 A
VUVLO1 UVLO Detect Voltage Falling 2.05 2.15 2.25 V
VUVLO1
VUVLO2 UVLO Released Voltage Rising 2.48 V
0.16
1.172 1.2 1.228
VREF VREF Voltage Tolerance VCC=3.3V V
VFB2 VFB2 VFB2
VREF Voltage Temperature
∆VREF/∆Topt VCC=3.3V, 40ºC≤Topt≤85ºC 150 ppm/ºC
Coefficient
∆VREF/∆VCC VREF Line Regulation 2.5V≤VCC≤5.5V 5 mV
∆VREF/∆IOUT VREF Load Regulation VCC=3.3V, 0.1mA≤IOUT≤2mA 5 mV
ILIMREF VREF Short Current Limit VCC=3.3V, VREF=0V 15 mA
VFB1 VFB1 Voltage Tolerance VCC=3.3V 0.985 1.0 1.015 V
VFB1 Voltage Temperature
∆VFB1/∆Topt VCC=3.3V, 40ºC≤Topt≤85ºC 150 ppm/ºC
Coefficient
IFB1 VFB1 Input Current VCC=5.5V, VFB1=0V or 5.5V 0.1 0.1 A
VFB2 VFB2 Voltage Tolerance VCC=3.3V 25 0 25 mV
IFB2 VFB2 Input Current VCC=5.5V, VFB2=0V or 5.5V 0.1 0.1 A
VCC=3.3V 240 300 360 kHz
fosc Oscillator Frequency VCC=3.3V 600 700 800 kHz
VCC=3.3V 1200 1400 1600 kHz
Maxduty1 CH1 Max. Duty Cycle VCC=3.3V 86 91 %
Maxduty2 CH2 Max. Duty Cycle VCC=3.3V 86 91 %
tSS1 CH1 Soft-start Time VCC=3.3V, VFB1=0.9V 4.5 ms
tSS2 CH2 Soft-start Time VCC=3.3V, VFB2=0.12V 4.5 ms
tDLY Delay Time for Protection VCC=3.3V 20 50 ms
RLX1 LX1 ON Resistance VCC=3.3V 400 m
IOFFLX1 LX1 Leakage Current VCC=5.5V, VLX1=20V 5 A
ILIMLX1 LX1 Current limit VCC=3.3V 1.0 1.5 A
RLX2 LX2 ON Resistance VCC=3.3V 400 m
IOFFLX2 LX2 Leakage Current VCC=5.5V, VLX=14.5V 5 A
ILIMLX2 LX2 Current limit VCC=3.3V 1.0 1.5 A
RVOUTN VOUTN Discharge Resistance VCC=3.3V, VOUTN=0.3V 10 25
VCEL CE "L" Input Voltage VCC=2.5V 0.3 V
VCEH CE "H" Input Voltage VCC=5.5V 1.5 V
ICEL CE "L" Input Current VCC=5.5V 1.0 1.0 A
ICEH CE "H" Input Current VCC=5.5V 1.0 1.0 A
6
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
TYPICAL APPLICATION
C1 L1
D1
LX1 VOUT1
C2
VCC R2 R3
PGND
C5
VFB1
R1
PVCC VOUTN
D2
C1B
VOUT2
LX2
R6 C3
L2
R5 C6
EN CE
VFB2
GND R4
VREF
C4
Pin Connection
Externally short VCC pin to PVCC pin. Externally short GND pin to PGND pin.
CE
0V
Negative output
Discharge Hi-Z
7
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
CE
CH1 (VOUT1)
CH2 (VOUT2)
CE CH1(VOUT1)
CH2(VOUT2)
Phase Compensation
DC/DC converter's phase may lose 180 degree by external components of L and C and load current. Because
of this, the phase margin of the system will be less and the stability will be worse. Therefore, the phase must be
gained.
8
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
VIN VOUT
IL1
CL
Lx Tr
<Current through L>
Discontinuous Mode Continuous Mode
IL ILxmax
IL
ILxmax
ILxmin
ILxmin
tf
t t
ton toff ton toff
T=1/fosc T=1/fosc
9
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
There are two operation modes for the PWM control step-up switching regulator, that is the continuous mode
and the discontinuous mode.
When the LX Tr. is on, the voltage for the inductor L will be VIN. The inductor current (IL1) will be;
When the Lx transistor turns off, power will supply continuously. The inductor current at off (IL2) will be;
In terms of the PWM control, when the tf=toff, the inductor current will be continuous, the operation of the
switching regulator will be continuous mode.
In the continuous mode, the current variation of IL1 and IL2 are same, therefore
In this moment, the peak current, ILxmax flowing through the inductor is described as follows:
ILxmax = IOUT VOUT / VIN + VIN T (VOUT VIN) / (2 L VOUT) .................................. Formula7
Therefore, peak current is more than IOUT. Considering the value of ILxmax, the condition of input and output,
and external components should be selected.
The explanation above is based on the ideal calculation, and the loss caused by Lx switch and external
components is not included.
The actual maximum output current is between 50% and 80% of the calculation.
Especially, when the IL is large, or VIN is low, the loss of VIN is generated with on resistance of the switch. As
for VOUT, VF(as much as 0.3V) of the diode should be considered.
10
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
<Basic Circuit>
Lx Tr Diode IOUT
VOUT
VIN
IL1 IL2 CL
Inductor
<Current through L>
Discontinuous Mode Continuous Mode
IL ILxmax
IL
ILxmax
ILxmin
ILxmin
Tf
t t
ton toff ton toff
T=1/fosc T=1/fosc
There are also two operation modes for the PWM control inverting switching regulator, that is the continuous
mode and the discontinuous mode.
When the LX Tr. is on, the voltage for the inductor L will be VIN. The inductor current (IL1) will be;
Inverting circuit saves energy during on time of Lx Tr, and supplies the energy to output during off time, output
voltage opposed to input voltage is obtained. The inductor current at off (IL2) will be;
In terms of the PWM control, when the tf=toff, the inductor current will be continuous, the operation of the
switching regulator will be continuous mode.
In the continuous mode, the current variation of IL1 and IL2 are same, therefore
11
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
In this moment, the peak current, ILxmax flowing through the inductor is described as follows:
ILxmax = IOUT |VOUT| / VIN + VIN |VOUT| T / { 2 L (|VOUT| + VIN) } ........................... Formula14
Therefore, peak current is more than IOUT. Considering the value of ILxmax, the condition of input and output,
and external components should be selected.
The explanation above is based on the ideal calculation, and the loss caused by Lx switch and external
components is not included.
The actual maximum output current is between 50% and 80% of the calculation.
Especially, when the IL is large, or VIN is low, the loss of VIN is generated with on resistance of the switch. As
for VOUT, VF (as much as 0.3V) of the diode should be considered.
12
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
TYPICAL
TYPCALCHARACTERISTICS
CHARACTERISTICS
1) Output Voltage VS. Output Current
R1283x001A R1283x001A
Topt=25°C Topt=25°C
4.8 -4.2
VIN=2.8V
4.7 -4.3 VIN=3.6V
VIN=4.2V
V OUT 1 [V]
V OUT 2 [V]
4.6 -4.4
VIN=2.8V
4.5 VIN=3.6V -4.5
VIN=4.2V
4.4 -4.6
0 50 100 150 200 0 50 100 150 200
IOUT1 [mA] IOUT 2 [mA]
R1283x001A R1283x001A
Topt=25°C Topt=25°C
12.6 -7.2
VIN=2.8V
12.4 -7.3
VIN=3.6V
12.2 -7.4 VIN=4.2V
V OUT 1 [V]
V OUT 2 [V]
VIN=2.8V
12.0 VIN=5.0V
-7.5
VIN=3.6V
11.8 VIN=4.2V -7.6
VIN=5.0V
11.6 -7.7
11.4 -7.8
0 25 50 75 100 125 150 0 50 100 150 200
IOUT1 [mA] IOUT2 [mA]
R1283x001B R1283x001B
Topt=25°C Topt=25°C
4.8 -5.2
VIN=2.8V
4.7 VIN=3.6V -5.3
VIN=4.2V
V OUT 1 [V]
V OUT 2 [V]
4.6 -5.4
VIN=2.8V
4.5 -5.5 VIN=3.6V
VIN=4.2V
4.4 -5.6
0 50 100 150 200 250 0 50 100 150 200
IOUT1 [mA] IOUT2 [mA]
13
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
R1283x001B R1283x001B
Topt=25°C Topt=25°C
12.6 -7.2
VIN=2.8V
12.4 -7.3
VIN=3.6V
12.2 VIN=4.2V -7.4
V OUT 1 [V]
V OUT 2 [V]
VIN=5.0V
12.0 -7.5
VIN=2.8V
11.8 -7.6 VIN=3.6V
VIN=4.2V
11.6 -7.7
VIN=5.0V
11.4 -7.8
0 50 100 150 200 250 0 100 200 300
IOUT1 [mA] IOUT2 [mA]
R1283x001C R1283x001C
Topt=25°C Topt=25°C
4.8 -4.2
VIN=2.8V
4.7 -4.3
VIN=3.6V
V OUT 1 [V]
V OUT 2 [V]
VIN=4.2V
4.6 -4.4
VIN=2.8V
4.5 -4.5
VIN=3.6V
VIN=4.2V
4.4 -4.6
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300
IOUT1 [mA] IOUT2 [mA]
R1283x001C R1283x001C
Topt=25°C Topt=25°C
12.6 -7.2
VIN=2.8V VIN=2.8V
12.4 -7.3
VIN=3.6V VIN=3.6V
12.2 VIN=4.2V -7.4 VIN=4.2V
V OUT 1 [V]
V OUT 2 [V]
VIN=5.0V VIN=5.0V
12.0 -7.5
11.8 -7.6
11.6 -7.7
11.4 -7.8
0 50 100 150 200 250 0 50 100 150 200 250 300 350
IOUT1 [mA] IOUT2 [mA]
14
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
Topt=25 , VVOUT
Topt=25°C, 1=4.6V
OUT1=4.6V Topt=25℃ , V OUT2=-4.4V
V OUT2=-4.4V , IOUT2=0mA V OUT1=4.6V , IOUT1=0mA
100 100
90 90
80 80
Efficiency [%]
Efficiency [%]
70 70
60 60
50 50
VIN=2.8 [V] VIN=2.8 [V]
40 VIN=3.6 [V] 40 VIN=3.6 [V]
30 VIN=4.2 [V] 30 VIN=4.2 [V]
20 20
0 20 40 60 80 100 120 140 160 180 0 20 40 60 80 100 120 140 160
R1283x001A R1283x001A
90 90
80 80
Efficiency [%]
Efficiency [%]
70 70
60 60
VIN=2.8 [V] VIN=2.8 [V]
50 50
VIN=3.6 [V] VIN=3.6 [V]
40 VIN=4.2 [V] 40
VIN=4.2 [V]
30 VIN=5 [V] 30 VIN=5 [V]
20 20
0 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 160
IOUT1 [mA]
IOUT2 [mA]
R1283x001B R1283x001B
Topt=25°C , V OUT1=4.6V
Topt=25°C , V OUT2=-5.4V
V OUT2=-5.4V , IOUT2=0mA
100 V OUT1=4.6V , IOUT1=0mA
100
90 90
80 80
Efficiency [%]
Efficiency [%]
70 70
60 60
50 50
VIN=2.8 [V] VIN=2.8 [V]
40 40 VIN=3.6 [V]
VIN=3.6 [V]
30 VIN=4.2 [V] 30 VIN=4.2 [V]
20
20
0 30 60 90 120 150 180
0 50 100 150 200 250
IOUT2 [mA]
IOUT1 [mA]
15
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
R1283x001B R1283x001B
Efficiency [%]
60 60
50 VIN=2.8 [V] 50 VIN=2.8 [V]
40 VIN=3.6 [V] 40 VIN=3.6 [V]
30 VIN=4.2 [V] 30 VIN=4.2 [V]
VIN=5 [V] VIN=5 [V]
20 20
10 10
0 30 60 90 120 150 180 210 0 40 80 120 160 200 240 280
IOUT1 [mA] IOUT2 [mA]
R1283x001C R1283x001C
Topt=25°C , V OUT2=-4.4V
Topt=25°C , V OUT1=4.6V
V OUT1=4.6V , IOUT1=0mA
V OUT2=-4.4V , IOUT2=0mA 100
100
90 90
80 80
70 70
Efficiency [%]
Efficiency [%]
60 60
50 50
40 VIN=2.8 [V] 40 VIN=2.8 [V]
30 VIN=3.6 [V] 30 VIN=3.6 [V]
20 VIN=4.2 [V] 20 VIN=4.2 [V]
10 10
0 40 80 120 160 200 240 280 320 0 50 100 150 200 250 300
IOUT1 [mA] IOUT2 [mA]
R1283x001C R1283x001C
90 90
80 80
70 70
Efficiency [%]
Efficiency [%]
60 60
50 VIN=2.8 [V] 50 VIN=2.8 [V]
40 VIN=3.6 [V] 40 VIN=3.6 [V]
30 VIN=4.2 [V] 30 VIN=4.2 [V]
20 VIN=5 [V] 20 VIN=5 [V]
10 10
0 30 60 90 120 150 180 210 240 0 40 80 120 160 200 240 280 320
16
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
Temperature
3) CE "L" Input Voltage VS. Temparature 4) CE "H" Input Voltage VS. Temperature
Temparature
R1283x00xx R1283x00xx
VIN=2.5V VIN=5.5V
1.1 1.1
1 1
VCEH [V]
VCEL [V]
0.9 0.9
0.8 0.8
0.7 0.7
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Temparature
5) VFB1 Voltage VS. Temperature 6) VFB2 Voltage VS. Temperature
Temparature
R1283x00xx R1283x00xx
1.02 0.01
1.01
0.005
1
VFB1 [V]
VFB2 [V]
0
0.99
-0.005
0.98
0.97 -0.01
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
Temparature
7) VREF Voltage VS. Temperature 8) UVLO Voltage VS. Temparature
Temperature
R1283x00xx R1283x00xx
1.22 2.4
1.21 2.35
2.3
1.2
UVLO Release
VUVLO [V]
VREF [V]
2.25
1.19
2.2
1.18
2.15
1.16 2.05
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C]
Topt [°C]
17
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
0.8 0.8
0.6 0.6
RLX1 [Ω]
RLX2 [Ω]
0.4 0.4
0.2 0.2
0 0
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
2 2
1.8 1.8
ILIMLX2 [mA]
ILIMLX1 [A]
1.6 1.6
1.4 1.4
1.2 1.2
1 1
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
Temperature
13) Osillator Frequency VS. Temparature
R1283x00xA R1283x00xB
350 800
330
750
FOSC [kHz]
FOSC [kHz]
310
700
290
650
270
250 600
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
18
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
R1283x00xC
1600
1500
FOSC [kHz]
1400
1300
1200
-40 -20 0 20 40 60 80
Topt [°C]
94 94
93 93
92 92
Maxduty1 [%]
Maxduty1 [%]
91 91
90 90
89 89
88 88
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
Temparature
15) Maxduty2 VS. Temperature
R1283x00xC R1283x00xA
94 92
93 91
92 90
Maxduty2 [%]
Maxduty1 [%]
91 89
90 88
89 87
88 86
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
19
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
R1283x00xB R1283x00xC
92 92
91 91
90 90
Maxduty2 [%]
Maxduty2 [%]
89 89
88 88
87 87
86 86
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
8 8
7 7
6 6
TSS2 [ms]
TSS1 [ms]
5 5
4 4
3 3
2 2
1 1
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
Temparature
18) Timer Latch Delay Time VS. Temperature 19) VOUTN Discharge Current VS. Temparature
Temperature
R1283x00xx R1283x00xx
100 0
80 -20
IVOUTN [mA]
TDLY [ms]
60 -40
40 -60
20 -80
-40 -20 0 20 40 60 80 -40 -20 0 20 40 60 80
Topt [°C] Topt [°C]
20
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
CE
15 0 15 0
Output Voltage [V]
Output Voltage [V]
12 12
9 9 V OUT1
V OUT1
6 6
3 3
0 0
-3 -3 V OUT 2:not discharge
V OUT 2 :discharge
-6 -6
-9 -9
0 5 10 15 20 0 5 10 15 20
Time [ms]
Time [ms]
15 0 15 0
Output Voltage [V]
Output Voltage [V]
12 12
9 9
V OUT1 V OUT1
6 6
3 3
0 0
-3 -3 V OUT 2:not discharge
-6 V OUT 2:discharge -6
-9 -9
0 5 10 15 20 0 5 10 15 20
Time [ms] Time [ms]
21
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
- 0
100
-7.4 -150
12.4
-7.5
12.2
-7.6
12.0 -7.7
0 1 2 3 4 5 0 1 2 3 4 5
R1283x00xB R1283x00xB
- 0
12.3 100
- -50
Output Voltage [V]
Output Voltage [V]
-7.4 -150
11.9
-7.5
11.7
-7.6
11.5 -7.7
0 1 2 3 4 5 0 1 2 3 4 5
Time [ms] Time [ms]
R1283x00xC R1283x00xC
- 0
12.3 100
Output Current [mA]
Output Current [mA]
- -50
Output Voltage [V]
Output Voltage [V]
-7.4 -150
11.9
-7.5
11.7
-7.6
11.5 -7.7
0 1 2 3 4 5 0 1 2 3 4 5
22
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
APPLIED CIRCUIT
1) Application with outputting power supply (+12V/-7.5V) for CCD from Li battery
3.6V
4.7uF
L1
SBD
LX 1 VOUT1= 12V
2) Application with outputting power supply (+4.6V/-4.4V) for AMOLED from Li battery
3.6V
4.7uF
L1
SBD
LX1 VOUT1= 4.6 V
VCC 1kΩ 10uF
36kΩ
PGND
C5
VFB1
10kΩ
VOUTN
PVCC SBD
LX2 VOUT2= 4.4 V
-
EN CE L2 1kΩ 10uF
56kΩ
C6
VFB2
GND 15kΩ
VREF
0.1uF
23
*1283Z (WLCSP-11-P2) is the discontinued product as of June, 2016.
R1283x
SBD
LX 1 VOUT1
VCC
PGND
EN
VFB1
LX 2 VOUT2
EN CE
VFB2
GND VREF
24
1. The products and the product specifications described in this document are subject to change or discontinuation of
production without notice for reasons such as improvement. Therefore, before deciding to use the products, please refer
to our sales representatives for the latest information thereon.
2. The materials in this document may not be copied or otherwise reproduced in whole or in part without prior written
consent of our company.
3. Please be sure to take any necessary formalities under relevant laws or regulations before exporting or otherwise
taking out of your country the products or the technical information described herein.
4. The technical information described in this document shows typical characteristics of and example application circuits
for the products. The release of such information is not to be construed as a warranty of or a grant of license under
our company's or any third party's intellectual property rights or any other rights.
5. The products listed in this document are intended and designed for use as general electronic components in standard
applications (office equipment, telecommunication equipment, measuring instruments, consumer electronic products,
amusement equipment etc.). Those customers intending to use a product in an application requiring extreme quality and
reliability, for example, in a highly specific application where the failure or misoperation of the product could result in
human injury or death (aircraft, spacevehicle, nuclear reactor control system, traffic control system, automotive and
transportation equipment, combustion equipment, safety devices, life support system etc.) should first contact us.
6. We are making our continuous effort to improve the quality and reliability of our products, but semiconductor products
are likely to fail with certain probability. In order to prevent any injury to persons or damages to property resulting from
such failure, customers should be careful enough to incorporate safety measures in their design, such as redundancy
feature, fire containment feature and fail-safe feature. We do not assume any liability or responsibility for any loss or
damage arising from misuse or inappropriate use of the products.
7. Anti-radiation design is not implemented in the products described in this document.
8. The X-ray exposure can influence functions and characteristics of the products. Confirm the product functions and
characteristics in the evaluation stage.
9. WLCSP products should be used in light shielded environments. The light exposure can influence functions and
characteristics of the products under operation or storage.
10. There can be variation in the marking when different AOI (Automated Optical Inspection) equipment is used. In the case
of recognizing the marking characteristic with AOI, please contact our sales or our distributor before attempting to use
AOI.
11. Please contact our sales representatives should you have any questions or comments concerning the products or
the technical information.
Official website
https://www.nisshinbo-microdevices.co.jp/en/
Purchase information
https://www.nisshinbo-microdevices.co.jp/en/buy/
Mouser Electronics
Authorized Distributor