Professional Documents
Culture Documents
JFE Steel Corporation, who holds ISO 9001, QS-9000 and ISO 14001
certifications, has made an effort for development and production of
various kinds of hot dip galvanized products thanks to most modern
facilities and long time accumulated technologies.
JFE's wide range of hot dip galvanized products include pure zinc coated,
alloy coated, and unique high corrosion resistance chemically treated steel
sheets which respond to the increasingly advanced and diverse needs of
changing markets. As the results, JFE has got sincere reliance from the
domestic and overseas customers.
Hot dip
galvanizing
2
HOT DIP GALVANIZED STEEL SHEET
Coating layer
Zinc Zinc-Iron alloy
steel steel
Characteristics
Full line from general processing to for deep drawing Same as JFE GALVAZINC. Full line from for general
Formability
products. processing to deep drawing products.
Weldability changes depending on zinc coating weight. Weldability is superior to that of normal zinc coated
However, thin coating weight of less than 60/60 have steel sheets due to Zn-Fe alloy coating. Same
Weldability
same weldability as cold rolled sheets under proper weldability as cold rolled sheets under proper welding
welding conditions. conditions.
Steel furniture, electric distributor panel, drum, pipe for Steel furniture, office appliance (desk, chair, locker,
Others
vinyl house, etc. cabinet, etc.), electric distributor panel, lamp oil tank, etc.
Coating layer
Zinc-5%Aluminum alloy 55%Aluminum-Zinc alloy
steel steel
Characteristics
Interior and exterior of architecture, electric facility, Industrial machinery, electric facility, civil and
Application
civil and architecture, automobile, etc. architecture, air conditioner, etc.
3
HOT DIP GALVANIZED STEEL SHEET HOT DIP GALVANIZED STEEL SHEET
Manufacturing process
Vacuum degasser
Blast furnace Converter Hot strip mill
Reheating furnace
Converter
Hot rolled coil
Blast furnace Continuous caster Scale breaker Rougher Finishing train
Manufacturing process
Manufacturing process
Pickled coil
Pickling line
Air cooling
Spangle equipment
Alloying equipment
Cooling tower
4 5
HOT DIP GALVANIZED STEEL SHEET
GALVALUME
STEEL SHEET
Special coat
High Special chromate - free
Lublicity Special Chromate -free coat JW + ◎ ー ◎ ̶ ◎
55% Aluminum - Zinc coat lubricant resin coating
Steel
Chromate coat
JFE
Normal Zinc coat C Normal chromate coating ○− ◎ ○ ○ △
GALVAZINC
Steel
6
HOT DIP GALVANIZED STEEL SHEET
JFE GALVAZINC
JFE GALVAZINC characteristics
JFE GALVAZINC products have superior corrosion resistance thanks to a thicker coating layer than
thin coated sheets with high formability and weldability. Produced by the continuous galvanizing line,
products has good coating adhesion and formability, combined with excellent corrosion resistance and
lubricity imparted by various chemical treatments.
Public standard
JFE standard
● JFE GALVAZINC for hot rolled soft base metal used ● JFE GALVAZINC for cold rolled soft base metal used
Classification Designation Classification Designation
JFE GALVAZINC
Structural quality, class 1 JFE-H400-GZ Structure quality, class 1 JFE-C400-GZ
Structural quality, class 2 JFE-H490-GZ Structure quality, class 2 JFE-C490-GZ
Commercial quality JFE-HB-GZ Commercial quality JFE-CB-GZ
Forming quality JFE-HC-GZ Forming quality JFE-CC-GZ
Drawing quality JFE-HD-GZ Drawing quality JFE-CD-GZ
Deep drawing quality FHE-GZ Deep drawing quality JFE-CE-GZ
Deep drawing quality with bake hardenability JFE-CH-GZ
Extra deep drawing quality, class 1 JFE-CF-GZ
Extra deep drawing quality, class 2 JFE-CG-GZ
● JFE GALVAZINC for hot rolled base metal used (High strength steel)
Designation Tensile strength level(N/mm2)
Classification
(・・・:Strength level) 310 370 400 440 490 590
Commercial quality JFE-HA・・・-GZ ○ ○ ○ ○ ○ ○
High stretch flange formability quality JFE-HA・・・SF-GZ ○
Low yield raio quality JFE-HA・・・Y-GZ ○
● JFE GALVAZINC for cold rolled base metal used (High strength steel)
Designation Tensile strength level(N/mm2)
Classification
(・・・:Strength level) 340 370 390 440 490 540 590
Commercial quality JFE-CA・・・-GZ ○ ○ ○ ○ ○
Deep drawing quality with bake hardenability JFE-CA・・・H-GZ ○
High yield ratio quality JFE-CA・・・R-GZ ○
Deep drawing quality JFE-CA・・・P-GZ ○ ○ ○ ○
Extra deep drawing quality JFE-CA・・・G-GZ ○ ○ ○ ○
Low yield ratio quality JFE-CA・・・Y-GZ ○
High stretch flange formability quality JFE-CA・・・SF-GZ ○
7
HOT DIP GALVANIZED STEEL SHEET HOT DIP GALVANIZED STEEL SHEET
JFE GALVAZINC
High strength steel for commercial quality JFE-HA400-GZ 255 245 400 31 32 33 − −
High strength steel for commercial quality JFE-HA440-GZ 275 440 25 26 27 − −
High strength steel for commercial quality JFE-HA490-GZ 315 490 21 22 23 24 − −
High strength steel for commercial quality JFE-HA590-GZ 440 590 18 19 20 − − −
High strength steel with high stretch flange formability quality JFE-HA440SF-GZ 305 440 28 29 31 32 − (70)
High strength steel for low yield ratio quality JFE-HA590Y-GZ 325 590 21 22 23 − −
Remarks 1. JIS No.5 test piece for tensile test taken in rolling direction.
2. Figures in parentheses are reference values.
8 9
HOT DIP GALVANIZED STEEL SHEET HOT DIP GALVANIZED STEEL SHEET
● JFE GALVAZINC for cold rolled base metal used (High strength steel)
Tensile Test Mean r-value Hole
BH Value
Yield Point min. (N/mm2) Elongation min. (%) min. Expanding
Tensile Ratio
Classification Designation Thickness mm strength Thickness mm Thickness mm
λ
min. min.
0.4 ≦ 0.8 ≦ 1.0 ≦ 0.4 ≦ 0.6 ≦ 0.8 ≦ 1.0 ≦ 1.2 ≦ 1.6 ≦ 2.0 ≦ 2.5 ≦ 0.5 ≦ 1.0< min.
(N/mm2) (N/mm2)
< 0.8 <1.0 ≦ 2.8 < 0.6 < 0.8 < 1.0 < 1.2 < 1.6 < 2.0 < 2.5 ≦ 2.8 ≦ 1.0 ≦ 1.6 (%)
Commercial quality JFE-CA340-GZ 215 205 195 340 32 33 34 35 36 37 − − − −
Commercial quality JFE-CA370-GZ 235 225 215 370 30 31 32 33 34 35 − − − −
Commercial quality JFE-CA390-GZ 255 245 235 390 28 29 30 31 32 33 − − − −
Commercial quality JFE-CA440-GZ 295 285 275 440 25 26 27 28 29 30 − − − −
Commercial quality JFE-CA490-GZ 335 325 315 490 20 21 22 23 24 25 − − − −
Deep drawing quality with bake hardenability JFE-CA340H-GZ 195 185 175 340 33 34 35 36 37 38 (1.3) (1.2) 30 −
High yield ratio quality JFE-CA590R-GZ 440 430 420 590 − 13 14 15 16 17 − − − −
JFE GALVAZINC
JFE GALVAZINC
Deep drawing quality JFE-CA340P-GZ 175 165 155 340 34 35 36 37 38 39 (1.4) (1.3) − −
Deep drawing quality JFE-CA370P-GZ 195 185 175 370 − 33 34 35 36 37 (1.3) (1.2) − −
Deep drawing quality JFE-CA390P-GZ 215 205 195 390 − 31 32 33 34 35 (1.3) (1.2) − −
Deep drawing quality JFE-CA440P-GZ 255 245 235 440 − 27 28 29 30 31 (1.3) (1.2) − −
Extra deep drawing quality JFE-CA340G-GZ 165 155 145 340 − 35 36 37 38 39 1.6 1.5 − −
Extra deep drawing quality JFE-CA370G-GZ 185 175 165 370 − 33 34 35 36 37 1.6 1.5 − −
Extra deep drawing quality JFE-CA390G-GZ 205 195 185 390 − 31 32 33 34 35 1.6 1.5 − −
Extra deep drawing quality JFE-CA440G-GZ 245 235 225 440 − 27 28 29 30 31 1.5 1.4 − −
Low yield ratio quality JFE-CA590Y-GZ 325 315 305 590 16 17 18 20 20 21 − − − −
High stretch flange formability quality JFE-CA440SF-GZ 330 320 310 440 22 23 24 25 26 27 − − − 70
Remarks 1. JIS No.5 test piece for tensile test taken transverse to rolling direction.
2. For thickness less than 0.6mm, the above tests are omitted if not specifically requested.
3. Figures in parentheses are reference values.
10 11
HOT DIP GALVANIZED STEEL SHEET
● JIS Products
Total coating weight on both sides Z08 Z10 Z12 Z18 Z20 Z22 Z25 Z27 Z35 Z45 (Z60)
Min. coating weight in triple-
80 100 120 180 200 220 250 275 350 450 (600)
spot test on both sides (g/m2)
Equivalent coating thickness (mm) 0.017 0.021 0.026 0.034 0.04 0.043 0.049 0.054 0.064 0.08 (0.102)
● JFE GALVAZINC
Total coating weight on both sides 45/45 60/60 75/75 90/90 120/120 140/140 150/150
Min. coating weight in triple-
60 80 100 120 180 200 220
spot test on both sides (g/m2)
Coating weight is measured by the triple-spot test specified in JIS H 0401.
JFE GALVAZINC
Spangle
12
HOT DIP GALVANIZED STEEL SHEET
Dimensional tolerance
JIS G 3302 is applied to strip dimensional tolerance. The thickness tolerance is shown below.
Thickness tolerance shall be apply to nominal thickness plus the equivalent thickness of coating.
JFE GALVAZINC
● Cold rolled base metal used Unit : mm
13
HOT DIP GALVANIZED STEEL SHEET
3.0 2.6×1380
2.3×1500
2.5 Available range
2.0 1.65×1733
2.0×1450
JFE GALVAZINC
1.5 1.6×1733
1.6×610
1.0
0.5
0.0
0 500 1000 1500 2000
Strip width (mm)
3.0
0.5
0.0
0 500 1000 1500 2000
Strip width (mm)
14
HOT DIP GALVANIZED STEEL SHEET
2.0
1.4×1830
1.5
JFE GALVAZINC
Available range
1.0
0.7×1830
0.5 0.6×1670
0.45×1300
0.4×610 0.4×1240
0.0
0 500 1000 1500 2000
Strip width (mm)
3.0
Strip thickness (mm)
2.5
2.0
1.6×610 1.6×1650
1.5 1.4×1820
15
HOT DIP GALVANIZED STEEL SHEET
3.5
3.0
Strip thickness (mm)
1.5
Available range
1.0
0.8×1640
0.5 0.45×610
0.5×1620
0.4×760 0.4×1230
0.0
0 500 1000 1500 2000
Strip width (mm)
3.0
Strip thickness (mm)
1.0 1.0×1530
0.8×1380
0.5
0.6×610 0.6×1280
0.0
0 500 1000 1500 2000
Strip width (mm)
16
HOT DIP GALVANIZED STEEL SHEET
Public standard
JFE standard
● JFE GALVAZINC ALLOY for hot rolled soft base metal used ● JFE GALVAZINC ALLOY for cold rolled soft base metal used
● JFE GALVAZINC ALLOY for hot rolled base metal used (High strength steel)
Designation Tensile strength level (N/mm2)
Classification
(・・・:Strength level) 310 370 400 440 490 590
Commercial quality JFE-HA・・・-GA ○ ○ ○ ○ ○ ○
High stretch flange formability quality JFE-HA・・・SF-GA ○
Low yield raio quality JFE-HA・・・Y-GA ○
● JFE GALVAZINC ALLOY for cold rolled base metal used (High strength steel)
Designation Tensile strength level (N/mm2)
Classification
(・・・:Strength level) 340 370 390 440 490 590
Commercial quality JFE-CA・・・-GA ○ ○ ○ ○ ○
Deep drawing quality with bake hardenability JFE-CA・・・H-GA ○
High yield ratio quality JFE-CA・・・R-GA ○
Deep drawing quality JFE-CA・・・P-GA ○ ○ ○ ○
Extra deep drawing quality JFE-CA・・・G-GA ○ ○ ○ ○
Low yield ratio quality JFE-CA・・・Y-GA ○
High stretch flange formability quality JFE-CA・・・SF-GA ○
17
HOT DIP GALVANIZED STEEL SHEET HOT DIP GALVANIZED STEEL SHEET
18 19
HOT DIP GALVANIZED STEEL SHEET HOT DIP GALVANIZED STEEL SHEET
● JFE GALVAZINC ALLOY for cold rolled base metal used (High strength steel)
Tensile Test Mean r-value Hole
BH Value
Yield Point min. (N/mm2) Elongation min. (%) min. Expanding
Tensile Ratio
Classification Designation Thickness mm strength Thickness mm Thickness mm
λ
min. min.
0.4 ≦ 0.8 ≦ 1.0 ≦ 0.4 ≦ 0.6 ≦ 0.8 ≦ 1.0 ≦ 1.2 ≦ 1.6 ≦ 2.0 ≦ 2.5 ≦ 0.5 ≦ 1.0< min.
(N/mm2) (N/mm2)
< 0.8 <1.0 ≦ 2.8 < 0.6 < 0.8 < 1.0 < 1.2 < 1.6 < 2.0 < 2.5 ≦ 2.8 ≦ 1.0 ≦ 1.6 (%)
Commercial quality JFE-CA340-GA 215 205 195 340 32 33 34 35 36 37 − − − −
Commercial quality JFE-CA370-GA 235 225 215 370 30 31 32 33 34 35 − − − −
Commercial quality JFE-CA390-GA 255 245 235 390 28 29 30 31 32 33 − − − −
Commercial quality JFE-CA440-GA 295 285 275 440 25 26 27 28 29 30 − − − −
Commercial quality JFE-CA490-GA 335 325 315 490 20 21 22 23 24 25 − − − −
Deep drawing quality with bake hardenability JFE-CA340H-GA 195 185 175 340 33 34 35 36 37 38 (1.3) (1.2) 30 −
High yield ratio quality JFE-CA590R-GA 440 430 420 590 − 13 14 15 16 17 − − − −
JFE GALVAZINC ALLOY
20 21
HOT DIP GALVANIZED STEEL SHEET
Coating weight
● JIS Products
Total coating weight on both sides F60 F08 F10 F12
Min. coating weight in triple-spot test
60 80 100 120
on both sides (g/m2)
Chemical treatment
Oiling
Oiling Designation
Oiling ○
No oiling ×
22
HOT DIP GALVANIZED STEEL SHEET
Dimensional tolerance
JIS G 3302 is applied to strip dimensional tolerance. The thickness tolerance is shown below.
Thickness tolerance shall be applied to nominal thickness plus the equivalent thickness of coating.
The measuring point is any points more than 25mm from the edge of the strip.
23
HOT DIP GALVANIZED STEEL SHEET
3.0 2.6×1380
2.3×1500
2.5 Available range
2.0 1.65×1733
2.0×1450
JFE GALVAZINC ALLOY
1.5 1.6×1733
1.6×610
1.0
0.5
0.0
0 500 1000 1500 2000
Strip width (mm)
3.0
0.5
0.0
0 500 1000 1500 2000
Strip width (mm)
24
HOT DIP GALVANIZED STEEL SHEET
2.0
1.4×1830
1.5
1.0
0.7×1830
0.5 0.6×1670
0.45×1300
0.4×610 0.4×1240
0.0
0 500 1000 1500 2000
Strip width (mm)
3.0
Strip thickness (mm)
2.5
2.0
1.6×610 1.6×1650
1.5 1.4×1820
25
HOT DIP GALVANIZED STEEL SHEET
3.5
3.0
Strip thickness (mm)
1.5
Available range
1.0
0.8×1640
0.5 0.45×610
0.5×1620
0.4×760 0.4×1230
0.0
0 500 1000 1500 2000
Strip width (mm)
Applicable standard : JFE-CA590R-GA
3.5
3.0
Strip thickness (mm)
1.0 1.0×1530
0.8×1380
0.5
0.6×610 0.6×1280
0.0
0 500 1000 1500 2000
Strip width (mm)
26
HOT DIP GALVANIZED STEEL SHEET
Public standard
JFE standard
27
HOT DIP GALVANIZED STEEL SHEET
Mechanical properties
Coating weight
● JIS products
Total coating weight on both sides AZ90 AZ120 AZ150 AZ170
Min. coating weight in triple-spot test on both sides (g/m2) 90 120 150 170
28
HOT DIP GALVANIZED STEEL SHEET
Dimensional tolerance
Dimension tolerance apply JIS G 3321.
Thickness tolerance of JIS G 3321 is shown below.
Width
≦ 1250
Nominal thickness
29
HOT DIP GALVANIZED STEEL SHEET
2.3×610
2.5 2.3×1300
Strip thickness (mm)
2.0
Available range
1.6×1370
GALVALUME STEEL SHEET
1.5
1.6×610
1.0
0 500 1000 1500
Strip width (mm)
1.5
0.6×1260
0.5
0.35×1220
0.35×610 0.27×1100
0.25×762 0.25×920
0.0
0 500 1000 1500
Strip width (mm)
30
HOT DIP GALVANIZED STEEL SHEET
JFE GALFAN
JFE GALFAN characteristics
JFE GALFAN has improved corrosion resistance by aluminum addition and good formability.
Because it has good paintability, JFE GALFAN is used in applications requiring paintability.
Widely used in building interiors and exteriors, and in automobiles, electrical appliances, etc.
Public standard
G 3317 Hot dip zinc-5% aluminum alloy coated steel sheets and coils SZAHC, SZACC,SZAH400, SZACD,SZAC400, etc.
JFE standard
JFE GALFAN
Classification Designation
31
HOT DIP GALVANIZED STEEL SHEET
Mechanical properties
Coating weight
JFE GALFAN
● JIS Product
Total coating weight on both sides Y08 Y10 Y12 Y18 Y20 Y22 Y25 Y27
2
Min. coating weight in triple-spot test on both sides (g/m ) 80 100 120 180 200 220 250 270
Equivalent coating thickness (mm) 0.014 0.018 0.023 0.028 0.037 0.043 0.046 0.058
JIS H 0401 is applied to coated weight measurement.
● JFE GALFAN
Total coating weight on both sides 45/45 60/60 90/90 120/120
2
Min. coating weight in triple-spot test on both sides (g/m ) 80 100 120 180
1) Coating weight is measured by the triple-spot test specified in JIS H 0401.
2) Coating weight not specified above is subject to negotiation.
32
HOT DIP GALVANIZED STEEL SHEET
2.0
JFE GALFAN
1.5
Available range
1.0
0.5
0.34×1220
0.25×610 0.25×920
0.0
0 500 1000 1500
Strip width (mm)
33
HOT DIP GALVANIZED STEEL SHEET
Eco-Frontier Series
Chromate-free Coated
Hot-dip Galvanized Steel Sheet = JC =
Optimum inorganic chromate-free coating for hot-dip zinc-coated steel sheets
Characteristics
1) Excellent corrosion resistance → White rust area less than 5% after SST 72 hrs
2) Good spot weldability → Same electrode life as conventional chromate coating *
3) Chromate-free coating → Environmentally-friendly chromate-free coated steel
3.0
Range subject to negotiation
2.5 2.30 × 610 2.30 × 1220
2.0 Available range for hot rolled substrate
(SGHC equivalent) 1.60 × 1250
1.5 (Hot rolled substrate is applied for 1.6mm or thicker)
Available range for cold rolled substrate
1.0
(SGCC equivalent)
0.5 0.35 × 610 0.40 × 1000 0.40 × 1250
Applications
1) Chassis for electrical appliances, etc.
2) Small parts for general applications
1) Coated layer might be removed or discolored during degreasing or cleaning in some case.
Please confirm it before use.
2) In case of severe bending and deep drawing, there is possibility of whitening or peeling of coated layer.
Please confirm it before use.
3) High temperature heating like brazing causes the damage of coating. Please handle at room temperature.
34
HOT DIP GALVANIZED STEEL SHEET
Eco-Frontier Series
Inorganic Chromate-free Coated
Hot-dip Galvanized Steel Sheet = JM =
Optimum inorganic chromate-free coating for hot-dip zinc-coated steel sheets
Characteristics
1) Excellent corrosion resistance → White rust area less than 5% after SST 72 hrs
2) Stable coating appearance after heating → Minimum coating deterioration after heating
3) Good spot weldability → Same electrode life as conventional chromate coating
30 sec. Chromate
After 72 C
hrs. SST Natural cooling
tested 6 7 8 9 10 11
by a flat Welding current (kA)
panel * Optimum current is different from conventional
*Coating itself is damaged by
chromate coat.
high temperature heating.
Current adjustment is required for JM coat.
Eco-Frontier Series
Available product size range of "JM", commercial quality
3.0
Commercial quality
2.5 2.30 × 610 2.30 × 1219
Strip thickness (mm)
0.0
400 600 800 1000 1200 1400
Strip width (mm)
Remarks; More information is available on other quality.
Applications
1) Chassis for electrical appliances, etc.
2) Small parts for general applications
1) Coated layer might be removed or discolored during degreasing or cleaning in some case.
Please confirm it before use.
2) In case of severe bending, deep drawing or use of adhesive tape, there is possibility of whitening or
peeling of coated layer. Please confirm it before use.
35
HOT DIP GALVANIZED STEEL SHEET
● Labeling
Products are packaged according to applicable
standards and preserved in a properly
controlled environment until shipment.
● Labeling
Labels showing the product standard,
dimensions, mass, and product serial no. are
attached to the product.
SG C C - JM - Z08
JFE - C C - GZ - JM - 60/60
(A) (B) (C) (D) (E) (F)
(A) Standards: SG=JIS hot dip zinc-coated steel sheets standard, JFE=JFE Standard
(B) Base metal used: C=Cold rolled steel sheets, H=Hot rolled steel sheets
(C) Classification: (JIS Standard) C=Commercial quality, D1=Drawing quality, class 1,
D2=Drawing quality, class 2, D3=Drawing quality, class 3
(JFE Standard) B=Commercial quality, C=Forming quality,
D=Drawing quality, E=Deep drawing quality
(D) Zn coating: GZ=JFE GALVAZINC=JFE hot-dip zinc-coated steel sheets
(E) Chromate-free chemical treatment
(F) Zinc coating weight (Top side/Bottom side)
4 Type of processing (In case of press forming, please show the part shape in detail.)
5 ● Coils : Maximum and minimum coil mass / Maximum coil outer diameter / Coil inner diameter / Acceptability of welded portion in coil
6 Other requirements (Surface finish, edge form, strip shape, oiling, etc.)
36
HOT DIP GALVANIZED STEEL SHEET
Handling precautions
In using hot dip galvanized steel sheets, the following precautions
should betaken in order to ensure optimum use:.
Handling precautions
[Handling] recommended. Undercoating with a wash
● Steel sheet products have sharp edges. primer will help ensure good results.
Handle carefully using gloves to avoid injury.
● Scratches and oil stain due to improper [Black discoloration]
handling can result in paint defects. ● Galvanized products (GZ : nonalloytype)
● Lubricated strips and sheets have a low may display a unique black discoloration
friction coefficient and slide easily. Coils may phenomenon which is caused by a very
collapse (telescope, etc.) due to repeated thin oxidized film near the zinc surface. This
uncoiling and recoiling. Cut sheets in piles results in changes in light absorption and
may slide due to impact. Use carefully in reflection, causing the material to appear
handling and work around storage areas. black, but does not affect the basic quality.
● Black discoloration tends to increase over
[Processing] time. The time until noticeable discoloration
● Some types of lubricating oil erode zinc. Prior occurs depends on operating conditions and
testing before using shall be recommended. the storage environment after production. As
an oxidation phenomenon, discoloration is
[Welding] generally accelerated by high temperature,
● For high temperature brazing, nickel-brass high humidity conditions.
brazing material is recommended. ● Black discoloration is unavoidable, but can
be delayed by oil coating. Quick use of
[Degreasing] products I recommended, as discoloration
● Insufficient degreasing can cause paint will increase if the product is stored for an
defects. extended period.
● Degreasing by spraying or dipping in a neutral
or low alkaline agent is recommended.
Strong alkaline agents can damage the strip
surface.
37
Cat.No.B1E-004-07
http://www.jfe-steel.co.jp/en/
TOKYO HEAD OFFICE Hibiya Kokusai Building, 2-3 Uchisaiwaicho 2-chome, Chiyodaku, Tokyo 100-0011, Japan
Phone : (81)3-3597-3111 Fax : (81)3-3597-4860
Notice
While every effort has been made to ensure the accuracy of the information contained within this publication, the use of the information is at
the reader’s risk and no warranty is implied or expressed by JFE Steel Corporation with respect to the use of information contained herein.
The information in this publication is subject to change or modification without notice. Please contact the JFE Steel office for the latest information.