Professional Documents
Culture Documents
Page 1/4
REFERENCE: Beam 1
Beam
Span, L
Section Size, Grade [m]
Rolled, SHS 50x50x4.0, S275 JR 1.350
Restraints
Left hand support type 3 Compression flange laterally restrained.
Nominal restraint against torsion.
Both flanges free to rotate on plan.
Start position End position Sub-beam length Eff. length Normal Eff. length Destab.
[m] [m] [m] [m] [m]
0.0 1.350 1.350 1.0000L 1.2000L
Right hand support type 3 Compression flange laterally restrained.
Nominal restraint against torsion.
Both flanges free to rotate on plan.
Design Loadcases
Point Load 1, Type: Imposed
F g1 g2 a b
Load Type [kN] [kN/m] [kN/m] [m] [m] Stability type
Point load 5.0 - - 1.200 - Normal
Point load 5.0 - - 0.050 - Normal
Design Combinations
Combination 1
Strength
Loadcase Factor Service Factor
Point Load 1 1.000 1.000
Combination 1
Classification check
Item Value Units Clause Ref.
Flange Class Class 1 Plastic Table 12
Web Class Class 1 Plastic Table 12
Section Class Class 1 Plastic Part 1: 3.5
Pass
Page 2/4
Flange Class
Item Value Units Clause Ref.
Flange, b/T 9.500
Flange, b/T limit 28.000
Flange Class Class 1 Plastic Table 12
Web Class
Item Value Units Clause Ref.
Web, d/t 9.500
Web, d/t limit 64.000
Web Class Class 1 Plastic Table 12
Support
Item Value Units Clause Ref.
Shear force, Fvx 5.4 kN
Design strength of steel, py 275.0 N/mm2 Part 1: 3.1.1, Table 9
Shear area, Avx 359 mm2 Part 1: 4.2.3
Shear capacity, Pvx 59.3 kN Part 1: 4.2.3
Shear Condition Low
Ratio 0.091
Pass
Page 3/4
Moment check
Position Critical Value Capacity Units Ratio Status
0.050 m 0.3 3.3 kNm 0.081 Pass
1.200 m 0.7 3.3 kNm 0.211 Pass
0.050 m
Item Value Units Clause Ref.
Moment, Mx 0.3 kNm
Design strength of steel, py 275.0 N/mm2 Part 1: 3.1.1, Table 9
Plastic modulus, Sxx 12.3 cm3
Elastic modulus, Zxx 10.0 cm3
Moment capacity, Mcx 3.3 kNm Part 1: 4.2.5
Ratio 0.081
Pass
1.200 m
Item Value Units Clause Ref.
Moment, Mx 0.7 kNm
Design strength of steel, py 275.0 N/mm2 Part 1: 3.1.1, Table 9
Plastic modulus, Sxx 12.3 cm3
Elastic modulus, Zxx 10.0 cm3
Moment capacity, Mcx 3.3 kNm Part 1: 4.2.5
Ratio 0.211
Pass
Deflection check
Condition Critical Value Limit Units Ratio Status
Imposed 2.2 3.8 mm 0.589 Pass
Total 2.2 6.8 mm 0.327 Pass
Imposed
Item Value Units Clause Ref.
Imposed 2.2 mm
Position 726.3 mm
Permissible 3.8 mm
Ratio 0.589
Pass
Permissible
Item Value Units Clause Ref.
Beam length 1.350 m
Span over 360
Total
Item Value Units Clause Ref.
Total 2.2 mm
Position 726.3 mm
Permissible 6.8 mm
Ratio 0.327
Pass
Page 4/4
Permissible
Item Value Units Clause Ref.
Beam length 1.350 m
Span over 200
Notes
Note
No notes!
Loading diagram
0.050
0.000 0.726 1.200 1.350
Shear diagram
0.050
0.000 0.726 1.200 1.350
5.4kN
-4.6kN
Moment diagram
0.050
0.000 0.726 1.200 1.350
0.7kNm
Deflection diagram
0.050
0.000 0.726 1.200 1.350
2.2mm