Professional Documents
Culture Documents
AIR-AP54GH
April, 2013
Note The power adapter can be directly connected to the AP too. In this way
you can connect your computer directly to the AP with an Ethernet cable.
Solid light
Flashing
Note If the LEDs display abnormally, please check to see if all the cable
connectors (power adapter and Ethernet cable) are well connected to your
device.
Note You will need to assign your computer a Static IP address within the
same range as the AP’s IP address. See the Troubleshooting T3 if you
need assistance.
Login
User nameǖadmin
Passwordǖadmin
Click OK
Note If the dialog box does not pop up, please refer to T3 in the Troubleshooting
guide. T2 will give you some help if you forget the password.
Click Next
Click Next
Note The AP supports three operation mode types: AP Client Router, AP2
Router and AP.
a) If you want to connect to your WISP, please choose AP Client
Router mode and proceed to AǗ
b) If you want to configure a point to point connection, please skip to B;
c) If you want to configure a repeater, please skip to C;
A. Configuration For WISP Client (CPE)
After choosing the AP Client Router mode on the above page, this page will then
display.
Click Next
Click Next
4
Click Next
Click Finish
1) The AP Setting
Select AP
Click Next
Click Finish
After successfully logging in, configure the other AIR-AP54GH by following the steps
below.
2) The Client Setting
Note You should change the default LAN IP address of the Client from
192.168.1.1 to 192.168.1.X (X can be any number from 1 to 253) to avoid
an IP conflict with the former AP. Here we choose 192.168.1.2 as an
example.
Click Network
Enter 192.168.1.2
in the IP Address
field.
Click Save
Select Client
Select Repeater
Click Survey
Hold it in for 8 to
10 seconds
Note Once the AP is reset, the current configuration settings will be lost and you
will need to reconfigure the router.
1) Restore the AP’s configuration to its factory default settings. If you don’t know
how to do that, please refer to previous section T1;
2) Use the default user name and password: admin, admin;
3) Try to reconfigure your AP by following the instructions of this QSG.
Now, try to log on to the Web-based configuration page again after configuring the
settings above. If you still cannot access the configuration page, please restore your
AP to its factory default settings and reconfigure your router following the instructions
of this QSG. Please feel free to contact our Technical Support if the problem
persists.
Right-click Local
Area Connection
Click Properties
Click OK
10
Click Properties
11
Click OK
12
Click OK
Now, try to log on to the Web-based configuration page again after the above
settings have been configured. If you still cannot access the configuration page,
please restore your AP’s factory default settings and reconfigure your AP following
the instructions of this QIG. Please feel free to contact our Technical Support if the
problem persists.
Note For more details about Troubleshooting and Technical Support contact
information, please logon to our Technical Support Website:
http://www.airnetwireless.net
13
www.airnetwireless.net
www.airnetwireless.net
14
Abril, 2013
15
Conecte su computadora
al puerto LAN del inyector
con un cable Ethernet.
Conecte el adaptador de
alimentación al inyector y
el otro extremo hacia un
toma corriente estándar.
Conecte su AP al puerto
PoE del inyector con un
cable Ethernet.
16
Sólido
Parpadeando
Sólido o parpadeando
Parpadeando si el Radio
inalámbrico está habilitado
Nota Si los LEDs se visualizan anormalmente, por favor verifique si todos los
cables están correctamente conectados al dispositivo (adaptador de
alimentación y cable Ethernet).
Ingresando
17
Usuarioǖadmin
Contraseñaǖadmin
Clic Aceptar
Clic Next
18
Clic Next
Clic Next
Clic Next
19
Clic Next
Nota El Usuario y Contraseña son proporcionados por su WISP.
Clic Finish
1) Configuración del AP
Seleccione AP
Clic Next
Seleccione su país de la
lista desplegable.
Clic Next
20
Clic Finish
Nota Usted debe cambiar la dirección IP por defecto del Cliente de 192.168.1.1
a 192.168.1.X (X puede ser cualquier número desde 1 a 253) para evitar
un conflicto IP con el anterior AP. Por ejemplo elija 192.168.1.2.
Clic Network
Ingrese 192.168.1.2 en
el campo IP Address.
Clic Save
Seleccione Client
21
Seleccione Repeater
Clic Survey
22
Presione de 8 a 10 segundos
23
Para Windows XP
Clic en Properties
(Propiedades)
24
Clic OK
25
Clic en Properties
(Propiedades)
26
Ingrese 192.168.1.100
dentro de Dirección IP y
255.255.255.0 dentro de
Máscara de subred.
Ingrese la Dirección de
servidor DNS dado por
su WISP o administrador
de red.
Clic OK
27
Clic OK
28
www.airnetwireless.net
www.airnetwireless.net
7109504521