Professional Documents
Culture Documents
A. API 580
B. API 578
C. API 579
D. API 577
A. 50
B. 30
C. 25
D. 40
Question 3 of 25 Time Remaining: 236
Question: During piping installation, what information should be documented for use in corrosion rate
calculations?
A. MAWP
B. 150% of design
C. ASME allowable stress
D. 90% of SMYS
Question 5 of 25 Time Remaining: 228
Question: The maximum interval between RBI assessments for Class 3 piping systems is:
A. 5 years.
B. 15 years.
C. owner-user option.
D. 10 years.
Question 6 of 25
Question: Numeric thickness readout gauges are based on:
Question: A complex listing and description of piping damage mechanisms experienced in the refining
A. API RP 571
B. API RP 580
C. API RP 574
D. API RP 579
Question 8 of 25 Time Remaining: 223
Question: Per API 570, which fo the following is an example of subsurface cracking?
A. hydrogen-induced cracking
B. creep
C. caustic stress corrosion cracking
D. fatigue
Question 9 of
25 Time Remaining: 217
Question: What is the purpose of recording a minimum alert thickness for a piping system?
A. to signal to the inspector that it is time for determining the pressure minimum
thickness
B. to signal to the inspector that it is time for determining the minimum structural
thickness
C. to signal to the inspector that a fitness-for-service assessment is necessary
D. to signal to the inspector that it is time for a remaining life assessment
Question 10 of 25 Time Remaining: 215
Question: The best search units for conducting corrosion evaluation are:
A. dual-element transducers.
B. single element delay transducers.
C. electromagnetic acoustic transducers.
D. multiple echo mode transducers.
Question 11 of 25 Time Remaining: 214
Question: When applying a hydrostatic test, the owner/user is cautioned to avoid exceeding what percentage of the
specified material yield strength?
A. 50%
B. 130%
C. 150%
D. 90%
Question 12 of 25 Time Remaining: 212
Question: According to API 570, guidance on the inspection of flanged joints can be found in:
A. API 579
B. ASME B31.3
C. ASME PCC-1
D. API 571
Question 13 of 25
Question: For service testing of Category D piping systems, ASME B 31.3 limits the gauge pressure
to be used for testing to:
A. MAWP.
B. 50 psi (344.8 kPa.
C. max design pressure.
D. 150 psi (1034.2 kPa).
Question 14 of 25 Time Remaining: 234
Question: Per API 570, the consequence of a release is dependent on:
A. By creating an interface that reflects the signal before it reaches the back wall.
B. By creating so much noise in the signal that the back-wall interface becomes indistinct.
C. By absorbing some of the sound and delaying the return signal to the transducer.
D. By changing the ultrasonic velocity as the signal passes through the inclusions.
Question 18 of 25 Time Remaining: 222
Question: In accordance with API 570, NDE examinations shall be scheduled at intervals that consider the:
A. a repair organization
B. the holder of a valid r-stamp
C. the holder of a valid v-stamp
D. the owner/user
Question 22 of 25
Question: Process piping that is supported by consecutive stanchions or sleepers is known as:
A. ASME B31.1
B. ASME B16.5
C. ASME B31.3
D. ASME B16.47
Question 7 of 25 Time Remaining: 224
Guduru Srinivasulu
If you have not already done so, please submit your application. API staff will process
your application and will issue your recertification documents.