Professional Documents
Culture Documents
Phone: 403.342.4494
Email: sales@canaltaflow.com
An ISO 9001:2008 registered company www.canaltaflow.com
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
Canalta applies a standard coating to all Dual Chamber Orifice HNBR O-ring Seals on both the body and seal bar come
Fittings that includes a non-lift red oxide primer and fast-drying standard with all Canalta Dual Chamber Orifice Fittings. This
enamel finish in Canalta Grey and burgundy top. Custom feature eliminates nuisance gasket maintenance and clamping
coatings for special environments - including maritime, humid, bar screw breakage, while providing superior sealing capability.
high temperature and others - custom colours and primer only The O-rings incorporated are standard shelf sizes and can be
applications are also available. supplied in a wide variety of compositions. Gaskets are also
available and can be used when preferred or required.
2 3
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
METER RUNS Whether the size is 2” or 30”, high or low pressure, wet, dry or corrosive service, we can put together a custom meter run
package that meets your specification or performance needs and perfectly matches your Canalta Orifice Fitting.
All Canalta Dual Chamber Orifice Fittings can be You trust Canalta at the orifice plate. When accuracy counts,
supplied with complete custom-designed Meter trust Canalta up and downstream, too.
Runs and Flow Conditioning Solutions We’ve been working to AGA-3 / API 14.3 and ISO 5167-1 specifications for over fifteen years. Skilled technicians, engineers
and inspectors work together to manufacture first-rate meter tubes out of pipe carefully selected and prepared with
that meet your exact specification or the appropriate surface requirements, roundness and I.D. tolerances. Hydrostatic test results are included as a standard.
PWHT stress relief, ultra-sonic and liquid dye penetration test results are available on request. Our rigorous inspection
performance needs. regime and comprehensive documentation mean you can be sure your meter run is reliable, exceptionally accurate and
ready for service.
4
5
1 2
stainless steel, to the compact Zanker or #50-style Flow Conditioners and Flow to fabricate nearly any combination of weldolets, sockolets, flanged outlets, (Left) (Right)
Conditioner Housings, we will help you develop the flow profile you need to threadolets and latrolets in any orientation.
achieve performance and accuracy in the field. 180
A-A
T.O.L. ORIENTATION
4 5
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
This is the standard seal assembly supplied with all orifice fittings from sizes 2”
through 8”. This unit is used with a .562” seal gap for fittings sizes 2” through 6”, and
with a .688” seal gap for 8” fittings. The single downstream seal function offers
superior sealing capability while reducing seal damage during insertion. Plate
FLOW
seal bypass tested down to 1” water column.
The seal assembly is comprised of an elastomer seal and one stainless
steel retainer ring. Exacting and repeatable concentricity is main-
tained with the metal to metal contact throughout the entire 360°
circumference of the orifice plate to the plate carrier mechanism. BEVEL
The Teflon Snap Seal provides positive plate sealing in the harshest of process
environments. The two-piece design snaps over the orifice plate without
the use of metal clips or retainers. A specially designed recess absorbs the
insertion pressures, minimizing permanent compression and distortion. FLOW
The raised section adjacent to the recess creates a positive seal against the
orifice plate, preventing bypass leakage. These two unique design features
enhance seal performance while extending the life expectancy
of the seal assembly. BEVEL
Bonded Seal
This is the standard seal supplied with all Canalta Orifice Fitting
model sizes 10" and larger. Designed with a unique "hollow
core" recess, this seal has impressive expansion and contraction
capabilities when compared to traditional solid rubber seals. FLOW
The recess allows the seal to absorb insertion pressures, mini-
mizing tearing, distortion and permanent compression. The 70
Duro HNBR seal is adhesively bonded to the orifice plate, creat-
ing total and permanent contact between the plate and seal
and preventing bypass leakage. BEVEL
6 7
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
TECHNICAL SPECIFICATIONS
Design . . . . . . . . . . . . . . . . . . . . . . . Orifice fittings supplied in Canada are built in accordance with the
ABSA Quality Control Program and carry a CRN registration number.
Industry Canada Approval Number AF-0014.
In compliance with ASME 16.34 and ASME 16.5, ASTM specifications,
AGA-3 Latest Edition and ISO-5167.
Body Materials . . . . . . . . . . . . . . . SA216 WCB, SA352 LCC or A351 CF8M Stainless Steel
Internal Parts . . . . . . . . . . . . . . . . . AISI 4130 Carbon Steel, 316 or A351 CF8M Stainless Steel
Sizes and ANSI Class . . . . . . . . . . 2” through 16”, 150 through 1500 ANSI raised face flange
18” through 30”, 150 through 600 ANSI raised face flange
600, 900 and 1500 flanges also available in RTJ face flange
Internal Bore Sizes . . . . . . . . . . . . 40, 60, 80, 100, 120, 160 and custom sizes
Line Bore I.D. Tolerance . . . . . . . In conformance with AGA-3 and ISO-5167 Latest Editions
Tap Connections . . . . . . . . . . . . . Two 1/2” NPT per side standard, two 1/2” NPT additional per side optional (TT)
2” and 3” fitting sizes center bored to .375” inside diameter
4” and larger sizes center bored to .500” inside diameter
Tolerance +/- 1/64”
Orifice Plate Seal Gap . . . . . . . . . 2” through 6” = 0.562”, 8” through 14” = 0.688”, 16” through 20” = 0.813”,
24” through 30” = 0.875”
Operating Shaft Location . . . . . Left hand mount standard on sizes 2” through 16”
Dual operation on sizes 20” and larger
Conformance
All fittings come standard with a documentation package including hydro-test, function test, inner valve seal
test, quality control inspection and material test reports. Trace ability is maintained in accordance with the
ISO-9001 Quality Control Program. The fittings are manufactured within the guidelines of ASME 16.34 and
ASME 16.5. When required, radiography, stress relief, ultra-sonic and liquid dye penetration tests can be per-
formed with the relevant report submitted.
Reporting
An AGA 2000 inspection report is included with the purchase of every fitting. The documented tests include:
• I.D. Bore Tolerance • Instrument Tap Diameter • Instrument Tap Location Our Quality Management systems guarantee that your Canalta Orifice
• Tap Communication • Plate Seal Test • Seal Protrusion Fittings are fully function and pressure tested, AGA-3, API 14.3 and ISO 5167
• Orifice Eccentricity • Bore Inside Diameter • Bore Roughness
compliant and ready for service
8 9
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
Clearance From
1K
Center Line to
Approximate
Weight (lbs.)
52
Operating
Operating
Changing
1J
Bottom
Center
Center
24
14
10G 1G
10C
1D
10E SIZE I L M N O P
10D ANSI 150 - Flangeneck - Standard Raised Face
18GH
2 10 5/8 12 7/8 4 1/4 4 1/4 13 5 9/16 100
3 13 5/8 13 3/4 5 5/16 4 7/8 14 6 1/16 145
18A 18B 18FH 4 12 3/8 14 1/8 5 13/16 5 31/99 15 1/2 7 240
5 37.5°
6 14 15/16 15 1/2 7 7 1/2 19 9 345
17A OSED
18EH 8 15 89/95 16 8 8 5/8 22 11 520 CL
10 16 3/16 17 3/8 9 10 1/16 25 13 1/8 610
A LI D E
18D
VE
16 12 19 7/16 18 7/8 10 3/4 11 3/4 27 7/8 15 1070
N
PE
SL
V
14 21 35/93 20 1/8 11 7/8 12 5/8 32 17 9/16 1287
O
9B 1 Seal Bar O-ring HNBR 20 3 Stuffing Box 4130 YZP CS 54 A/R Slide Valve Lubricant Grease
M L 1”
10C 1 Bleeder Valve Body 4130 YZP CS / 316 SS 20A 3 Stuffing Box Outer Gland Seals HNBR 55 3 Eccentricity Alignment Pins 18/8 SS
10D 1 Bleeder Valve Needle 4130 YZP CS / 316 SS 22A 6 Stuffing Box Gaskets 316 SS 56 3 Eccentricity Alignment Plugs
10 To find the latest editions of the complete data tables, visit us online at www.canaltaflow.com 11
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
Clearance From
Center Line to
Approximate
Weight (lbs.)
Operating
Operating
Changing
Bottom
Center
Center
SIZE I L M N O P
ANSI 150 - Flange x Flange - Standard Raised Face
2 10 5/8 12 7/8 4 1/4 4 1/4 13 5 9/16 105
3 12 7/8 13 3/4 5 5/16 4 7/8 14 6 1/16 155
4 12 3/8 14 1/8 5 13/16 5 31/99 15 1/2 7 255
6 14 15/16 15 1/2 7 7 1/2 19 9 365
8 15 15/16 16 8 8 5/8 22 11 550 37.5°
OSED
10 14 5/8 17 3/8 9 10 1/16 25 13 1/8 655 CL OSED
CL
12 19 7/16 18 7/8 10 3/4 11 3/4 27 7/8 15 1130
A LI D E
VE
A LI D E
N
14 21 3/8 20 1/8 11 7/8 12 5/8 32 17 9/16 1370
VE
PE
SL
N
V
PE
O
SL
ANSI 300 - Flange x Flange - Standard Raised Face O V
Clearance From
Clearance From
1.000
Center Line to
Approximate
3
Weight (lbs.)
13 1/8 13 3/4 5 5/16 4 7/8 14 6 1/16 170
Operating
Operating
Changing
1.000
Bottom
4 12 11/16 14 1/8 5 13/16 5 31/99 15 1/2 7 275
Center
Center
1.000
6 15 3/8 15 1/2 7 7 1/2 19 9 405
8 16 7/16 16 8 8 5/8 22 11 605
10 16 7/8 17 3/8 9 10 1/16 25 13 1/8 730
12 19 7/16 18 7/8 10 3/4 11 3/4 27 7/8 15 1245 1/16”
14 21 3/8 20 1/8 11 7/8 12 5/8 32 17 9/16 1510 SIZE I L M N O P
ANSI 600 - Flange x Flange - Standard Raised Face ANSI 1500 RTJ - Flangeneck Configuration - Ring Type Joint Flange
2 10 5/8 12 7/8 4 1/4 4 1/4 13 5 9/16 115
2 14 1/8 12 7/8 5 3/4 4 1/2 13 3/4 5 9/16 205
3 13 3/8 13 3/4 5 5/16 4 7/8 14 6 1/16 175
4 13 1/4 14 1/8 5 13/16 5 31/99 15 1/2 7 300 3 15 3/4 13 3/4 5 5/8 5 5/8 15 6 1/16 275
6 16 1/16 15 1/2 7 7 1/2 19 9 480
I 4 16 3/8 14 1/8 6 1/2 6 1/8 16 1/4 7 445 I
8 17 1/4 16 8 8 5/8 22 11 700 6 21 1/16 15 1/2 7 3/4 8 19 3/8 9 710
10 17 3/4 17 3/8 9 10 1/16 25 13 1/8 925 8 23 1/8 16 9 3/4 9 1/2 22 1/2 11 1240
MINIMUM CLEARANCE 10 25 1/4 17 3/8 11 11 1/2 25 1/2 13 1/8 1745 MINIMUM CLEARANCE
12 19 7/16 18 7/8 10 3/4 11 3/4 27 7/8 15 1430
14 21 3/8 20 1/8 11 7/8 12 5/8 32 17 9/16 1735 P REQ’D FOR PLATE CHANGING 12 26 15/16 18 7/8 12 3/8 13 1/4 28 1/4 15 2805 P REQ’D FOR PLATE CHANGING
ANSI 600 - Flange x Flange - Ring Type Joint ANSI 1500 RF - Flangeneck Configuration - Standard Raised Face
2 10 7/8 12 7/8 4 1/4 4 1/4 13 5 9/16 115 2 14 1/8 12 7/8 5 3/4 4 1/2 13 3/4 5 9/16 205
3 13 1/2 13 3/4 5 5/16 4 7/8 14 6 1/16 175 3 15 3/4 13 3/4 5 5/8 5 5/8 15 6 1/16 275
4 13 3/8 14 1/8 5 13/16 5 31/99 15 1/2 7 300 4 16 3/8 14 1/8 6 1/2 6 1/8 16 1/4 7 445
6 16 1/8 15 1/2 7 7 1/2 19 9 480
6 21 1/16 15 1/2 7 3/4 8 19 3/8 9 710
8 17 5/16 16 8 8 5/8 22 11 710
10 17 13/16 17 3/8 9 10 1/16 25 13 1/8 925 8 23 1/8 16 9 3/4 9 1/2 22 1/2 11 1240
12 19 7/16 18 7/8 10 3/4 11 3/4 27 7/8 15 1430 10 25 1/4 17 3/8 11 11 1/2 25 1/2 13 1/8 1745
14 21 3/8 20 1/8 11 7/8 12 5/8 32 17 9/16 1735 12 26 15/16 18 7/8 12 3/8 13 1/4 28 1/4 15 2805
ANSI 900 - Flange x Flange - Standard Raised Face
2 12 3/4 12 7/8 4 1/4 4 1/4 13 5 9/16 230
3 13 7/8 13 3/4 5 5/16 4 7/8 14 6 1/16 245 O O
4 13 1/2 14 1/8 5 13/16 5 31/99 15 1/2 7 355
6 16 3/8 15 1/2 7 7 1/2 19 9 600
8 18 1/4 16 8 8 5/8 22 11 1265
10 18 17 3/8 9 10 1/16 25 13 1/8 1800
12 19 7/16 18 7/8 10 3/4 11 3/4 27 7/8 15 2260
14 21 3/8 20 1/8 11 7/8 12 5/8 32 17 9/16 2515
ANSI 900 - Flanged - Ring Type Joint
2 12 7/8 12 7/8 4 1/4 4 1/4 13 5 9/16 230
3 14 13 3/4 5 5/16 4 7/8 14 6 1/16 245
4 14 37/79 14 1/8 5 13/16 5 31/99 15 1/2 7 355
6 16 1/2 15 1/2 7 7 1/2 19 9 600
8 17 5/8 16 8 8 5/8 22 11 1265
10 18 1/16 17 3/8 9 10 1/16 25 13 1/8 1800 N N
12 19 7/16 18 7/8 10 3/4 11 3/4 27 7/8 15 2260
14 21 3/8 20 1/8 11 7/8 12 5/8 32 17 9/16 2495
M 1”
L M L 1”
12 To find the latest editions of the complete data tables, visit us online at www.canaltaflow.com 13
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
Clearance From
23B 1 Grease Gun Body 4130 YZP CS / 316 SS
Center Line to
Approximate
Weight (lbs.)
Operating
Operating
Changing
24 1 Double Ball Grease Check Valve 316 SS
Bottom
Center
Center
25 6 Packing Nuts 4130 YZP CS
A/R = As required
14 15
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
DIAGRAMS, WEIGHTS & DIMENSIONS - 16” DUAL CHAMBER MODELS DIAGRAMS, WEIGHTS & DIMENSIONS - 18” - 30” DUAL CHAMBER MODELS
Flange x Flange (Raised Face / Ring Type Joint) 8H 8
58
Clearance From
Center Line to
Approximate
Weight (lbs.)
Operating
Operating
Center
ANSI 150 - Flange x Flange - Standard Raised Face 28A 6 Bushing Retainer - Stuffing Box 316 SS
20” - 30” Dual Chamber Models
16 22 5/8 23 1/4 23 1/4 13 1/2 35 3/8 19 1/2 2060 30 2 Drain Plugs A105 CS / 316L SS Item Qty. Description Material
ANSI 300 - Flange x Flange - Standard Raised Face 31 2 Meter Tap Plugs (Qty = 6 with teletaps) A105 CS / 316L SS 44A 1 Travel Brake Body WCB Steel
16 22 5/8 23 1/4 23 1/4 13 1/2 35 3/8 19 1/2 2300 1” 32 A/R Hex Nuts A194 YZP CS - 2HM 44B 1 Brake Band Brass
ANSI 600 - Flange x Flange - Standard Raised Face REQ’D FOR 33 A/R Body Studs A193 YZP CS - B7M 44C 1 Brake Adjustment Bolt YZP Steel
16 N REMOVAL OF
22 5/8 23 1/4 23 1/4 13 1/2 35 3/8 19 1/2 2680 35B 2 External Shaft Roller 1018 CS 44D 1 Brake Sleeve Carbon Steel
WRENCH
ANSI 600 - Flange x Flange - Ring Type Joint 36 1 External Shaft 1018 CS 44E 1 Hex Head Bolt Steel
16 22 5/8 23 1/4 23 1/4 13 1/2 35 3/8 19 1/2 2680 37C 4 Shaft Bushing Brass 50 1 Specification Plate Color Etched 316 SS
ANSI 900 - Flange x Flange - Standard Raised Face 41 1 Plate Carrier Guide (left & right) Cast Carbon Steel 52 2 Operating Plates Color Etched 316 SS
16 22 5/8 23 1/4 23 1/4 13 1/2 35 3/8 19 1/2 2867 41B 4 Plate Carrier Guide Bolts YZP Steel 54 A/R Slide Valve Lubricant Grease
ANSI 900 - Flanged - Ring Type Joint 42A 1 Plate Carrier Stop Carbon Steel 55 3 Eccentricity Alignment Pins 18/8 SS
16 22 5/8 23 1/4 23 1/4 13 1/2 35 3/8 19 1/2 2867 L L 42B 1 Plate Carrier Stop Bolt B7 Bolting 56 3 Eccentricity Alignment Pin Plugs
42C 1 Plate Carrier Stop Bushing Brass 58 1 Plate Carrier Alignment Screw 18/8 SS
A/R = As required
16 17
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
37.5° ±2.5°
O O
I
I
Overall Face to Face
Clearance From
Operating
Center Line to
Changing
Approximate
Weight (lbs.)
Bottom
Center
Operating
Changing
Bottom
Center
SIZE I L N O P
ANSI 150 - Flanged - Standard Raised Face - MWP: 275 PSIG SIZE I L N O P
18 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 2711 ANSI 150 - Flange x Flange - Standard Raised Face - MWP: 275 PSIG
20 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 2711 18 26 1/2 25 1/4 16 1/4 54 1/8 11 1/8 2866
24 26 7/8 28 1/16 18 1/2 60 7/8 15 4073 20 26 1/2 25 1/4 16 1/4 54 1/8 11 1/8 2866
26 31 36 1/2 20 65 5/8 18 3/4 6846 24 26 7/8 28 1/16 18 1/2 60 7/8 15 4283
30 35 40 27 71 1/2 22 3/4 14750 26 31 36 1/2 20 65 5/8 18 3/4 7094
ANSI 300 - Flanged - Standard Raised Face - MWP: 740 PSIG 30 35 40 27 71 1/2 22 3/4 15000
1” ANSI 300 - Flange x Flange - Standard Raised Face - MWP: 740 PSIG 1”
18 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3051
REQ’D FOR 18 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3376 REQ’D FOR
20 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3051
REMOVAL OF 20 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3376 REMOVAL OF
24 26 7/8 28 1/16 18 1/2 60 7/8 15 4633 N N
WRENCH 24 26 7/8 28 1/16 18 1/2 60 7/8 15 5123 WRENCH
26 31 36 1/2 20 65 5/8 18 3/4 7454
26 31 36 1/2 20 65 5/8 18 3/4 8006
30 35 40 27 71 1/2 22 3/4 15500
30 35 40 27 71 1/2 22 3/4 16500
ANSI 600 - Flanged - Standard Raised Face - MWP: 1440 PSI
ANSI 600 - Flange x Flange - Standard Raised Face - MWP: 1440 PSI
18 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3625
18 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 4237
20 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3625
20 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 4237
24 26 7/8 28 1/16 18 1/2 60 7/8 15 5405
24 26 7/8 28 1/16 18 1/2 60 7/8 15 6281
26 31 36 1/2 20 65 5/8 18 3/4 8146
26 31 36 1/2 20 65 5/8 18 3/4 9044
30 35 40 27 71 1/2 22 3/4 16500 L L L L
30 35 40 27 71 1/2 22 3/4 17500
ANSI 600 - Flanged - Ring Type Joint - MWP: 1440 PSIG
ANSI 600 - Flange x Flange - Ring Type Joint - MWP: 1440 PSIG
18 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3625
18 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 4417
20 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 3625
20 26 1/2 25 1/4 16 1/4 54 1/8 23 1/8 4417
24 26 7/8 28 1/16 18 1/2 60 /7/8 15 5405
24 26 7/8 28 1/16 18 1/2 60 /7/8 15 6885
26 31 36 1/2 20 65 5/8 18 3/4 8146
26 31 36 1/2 20 65 5/8 18 3/4 9596
30 35 40 27 71 1/2 22 3/4 16500
30 35 40 27 71 1/2 22 3/4 18500
18 To find the latest editions of the complete data tables, visit us online at www.canaltaflow.com 19
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
INSTALLATION RECOMMENDATIONS OPERATING INSTRUCTIONS - ALL DUAL CHAMBER MODELS WARNING: PRESSURIZED UNIT.
Ensure all operating staff are trained
in the safe operation of this an all
The Dual Chamber Orifice Fitting is typically installed in conjunction with upstream and downstream meter
other pressurized equipment.
run sections (tubes). This is essential to meet the recommendations of both AGA Report 3 and ISO 5167. To To remove the orifice plate
obtain the best measurement results, follow the recommended piping configurations and installation re- (a) Open the equalizer valve (1) to match pressure levels in the fitting body and top housing.
quirements of either of these two standards, as well as the recommendations below. (b) Open the slide valve (5).
(c) Rotate the lower plate carrier pinion gear (6) to raise the plate carrier into the top housing.
1. Always ensure that operation staff are competent and properly trained to operate this and all other pressurized (d) Rotate the upper plate carrier pinion gear (7)until the plate carrier makes contact with the seal bar (9).
equipment. (e) Close the slide valve (5) to seal off the fitting body from the top housing.
(f ) Close the equalizer valve (1).
2. Attention to clearances is essential. Consult the attached dimensional drawings and tables for details. Ensure there
(g) Open the bleeder valve (10B) to release pressure from the top housing.
is operating clearance at the sides of the fitting for pinion gear rotation and operating wrench removal. Ensure, too,
that there is clearance above the top of the fitting for removal of the orifice plate carrier.
(h) Lubricate the slide valve through the grease gun (23) (see facing page).
(i) Loosen the clamping bar screws (11). DO NOT REMOVE THE CLAMPING BAR (12).
3. When installing the fitting or meter run, check that the flow arrow corresponds to the direction of flow in the line. (j) Raise the plate carrier by rotating the upper plate carrier pinion gear (7) to loosen the seal bar (9).
(k) Remove the clamping and seal bars (12, 9).
4. The unit can be installed either in a vertical or horizontal flow orientation. When mounting horizontally, the top (l) Rotate the upper plate carrier pinion gear (7) to raise the orifice 11
housing should be located in the upper position for ease of operation as well as to avoid liquid and debris from plate and carrier up and out of the top housing.
accumulating in the upper chamber. 12
5. When used to measure wet gas, the vertical mount is recommended to prevent dam formation against the orifice WARNING: The unit may be under extreme
9
plate. high pressure. Failure to depressurize the top
housing before attempting to remove the seal
6. Instrument tap lines should be installed sloping upward to the differential pressure measurement instrument. Where
10B
this cannot be accomplished, use seal pots to chemically seal the sensing lines in order to eliminate hydrostatic head bar may result in bodily harm or death. Follow
errors. all instructions carefully. Stay clear of the top 7
23
7. After the orifice fitting has been piped in, install the bleeder valve, grease gun and indicator plate on the slide valve opening at all times and ensure that the bleeder
pinion gear. valve is vented away safely. 1
8. With the two drive screws provided, install the valve position pointer. Ensure that the position on the valve indicator
plate corresponds with the position of the slide valve. To replace the orifice plate 6
5
(A) Close the bleeder valve (10B).
9. It is recommended that the bleeder valve vent be piped away from the fitting to a safe venting area. (B) Rotate the upper plate carrier pinion gear (7) slowly until the plate car-
rier clears the seal bar level. DO NOT LOWER THE PLATE CARRIER ONTO THE SLIDE VALVE.
10. To avoid damage to the orifice plate, ensure the orifice plate and plate carrier are removed from the fitting prior to (C) Replace the seal and clamping bars (9, 12).
pressure testing the system. (D) Tighten the clamping bar screws (11).
(E) Open the equalizer valve (1) to match pressure levels in the fitting body and top housing.
11. Before inserting the orifice plate and plate carrier into the fitting, always ensure that the lower cavity of the fitting is (F) Open the slide valve (5).
free of debris. If debris has accumulated, remove the lower drain plugs and rod-clean the lower section.
(G) Rotate the upper plate carrier pinion gear (7) to lower the plate carrier into the fitting body.
12. Dual Chamber Orifice Fittings equipped with the grease style slide valves were lubricated at the factory prior to
(H) Rotate the lower plate carrier pinion gear (6) until the carrier makes contact with the bottom of the fitting.
shipment. If the unit has been sitting out of service for more than six months, it is recommended that the unit be (I) Close the slide valve (5) to seal off the top housing from the fitting body.
lubricated prior to being put into service. Refer to the “Lubrication Procedure”. (J) Close the equalizer valve (1).
(K) Open the bleeder valve (10B) to release pressure from the top housing.
13. To avoid over range damage to the differential measurement instruments and orifice plate during initial (L) Lubricate the slide valve through the grease gun (23) (see facing page).
pressurization, ensure the orifice plate is rolled up out of the flow stream and that the instrument manifold equalization (M) Close the bleeder valve (10B).
valves are open.
These instructions are attached to the top housing of each Canalta Dual Chamber Orifice Fitting. Ensure
that all operating staff are fully trained in the safe operation of this and all other pressurized equipment.
20 21
For more information or to order, contact us at Phone: 403.342.4494 | Fax: 403.346.7110 | Email: sales@canaltaflow.com | Web: www.canaltaflow.com
An ISO 9001:2008 Registered Company
Greasing Procedures
1. Ensure the slide valve (5) and equalizer valve (1) are in the closed position.
2. Open the bleeder valve (10B) and allow the top chamber to depressurize.
3. Remove the threaded stem (23A) from the grease gun assembly (23). Insert one stick of grease.
4. Replace the stem and turn in slowly so as not to rupture the inner
body seals. A half stick of grease should suffice to lubricate the
valve.
5. Should additional grease be required, repeat steps 3 and 4. Grease
Stick
Larger fittings will require more grease.
23A
PREVENTIVE MAINTENANCE
The Canalta Dual Chamber Orifice Fitting has a number of moving
parts that benefit from a regular preventive maintenance program.
The following procedures are recommended:
1. Remove and inspect the orifice plate and seal monthly. Replace as required.
2. Grease the slide valve as per operating instructions (see above), or monthly.
3. Disassemble the orifice fitting every two years or earlier if deemed necessary. Inspect the inner working
parts for corrosion and wear. Replace the working parts as required and replace all seals prior to reassembly.
22 23
ADDITIONAL PRODUCT LINES
Canalta also offers a complete lineup of products to fulfill your orifice metering requirements.
Visit us on the web at www.canaltaflow.com to get all the information, or contact us to
request print materials.
CONTACT INFORMATION
The "Canalta Flow Measurement" name and logo are trademarks of Canalta Controls Ltd. All other trademarks are the property of their respective companies.
All information presented here is for information purposes only. Though every effort has been made to ensure their accuracy, the contents of this publication shall not be
construed as warranties or guarantees, expressed or implied, regarding the products or services described herein, or their use or applicability. Due to Canalta’s commitment
to quality and innovation, all product designs, specifiactions and information material, including the contents of this publication, are subject to change without notice.
Responsibility for the proper selection, maintenance and use of any product remains with the customer. SAFETY FIRST.
Copyright, tradementark and other forms of proprietary rights protect the contents of this publication.
© 2011 Canalta Controls Ltd. All rights reserved. Unauthorized reproduction in whole or in part is prohibited.