Professional Documents
Culture Documents
k foHkkx
INDEX
Sl.
Chapter Description Page No.
No.
1 - INDEX 1
2 - OFFICE ORDER 2
3 - IMPORTANT INSTRUCTIONS 3-6
4 - EXTRA CONDITIONS FOR LABOUR WORK ONLY 7
5 1 MATERIALS 8-16
6 2 LABOUR 17-18
7 3 CARTAGE 19-22
8 4 EARTH WORK 23
9 5 CONCRETE WORK 24-25
10 6 BRICK WORK 26
11 7 DAMP PROOF COARSE 27
12 8 ANTI TERMITE TREATMENT 28
13 9 DOORS & WINDOWS 29-33
14 10 MILD STEEL & IRON WORK 34-36
15 11 ROOF WORK 37-40
16 12 CEILING AND LINING 41-45
17 13 PLASTER & POINTING 46-48
18 14 FLOORING 49-52
19 15 PAINTING & DISTEMPERING 53-56
20 16 WHITE WASHING & COLOUR WASHING 57
21 17 DEMOLITION & DISMANTLING 58-59
22 18 MARBLE WORK IN WALL LINING ETC. 60
23 19 MISCELLANEOUS 61-62
24 20 ROAD WORK 63-66
25 21 WATER SUPPLY MATERIALS 67-69
26 22 SANITARY MATERIALS 70-71
27 23 WATER SUPPLY WORKS 72-80
28 24 SANITARY FITTINGS 81-84
29 25 DRAINAGE 85-87
30 26 ANNUAL REPAIRS 88
31 27 TRAFFIC SIGN 89-90
32 - CONSUMPTION OF BUILDING MATERIALS 91-92
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
CHAPTER-1
MATERIAL
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
1- BRICK
(a) Class 150 1.1.1 1000 Nos 5800.00
(b) Class 100 1.1.2 1000 Nos 5600.00
(c ) Straight over brunt Class-275 1.1.4 1000 Nos 5400.00
(d) Tiles, Bull Nose Drip Course Brick 1.1.4 1000 Nos 5700.00
2- BRICK BALLAST
(a) Overburnt brick ballast 40mm gauge 1.2 Cum 1200.00
(b) Class-150 brick ballast 25mm gauge 1.2 Cum 1300.00
(c ) Brick Bats of O.B.B./Class150 1.2 Cum 900.00
Fly ash Brick (Specification/Strengh should not be less than bricks
2(A) 1000 Nos 6100.00
150) (Size-230mmx110mmx75mm)
Autoclaved Aerated Concrete (AAC) Block conforming to IS-2185-
2(B) 2005(part-III) including loading, cartage upto site, unloading, cum 3000.00
stacking including all levies and octroi, royalities if any
3(A) STONE BALLAST (From Khera Thakur Quarry)
45-90 mm guage stone ballast. Cum 550.00
3(B) CRUSHED STONE BALLAST /GRIT (From Ghatri Quarry)
45-63 mm guage stone ballast. Rates as Cum 650.00
22.4-53 mm guage stone ballast. per S.E. Cum 750.00
40mm guage stone ballast Agra Circle, Cum 875.00
20mm guage stone ballast PWD, Agra Cum 875.00
Letter No.-
Crushed stone Dust 2.36mm & below Cum 625.00
14/ 2m-
13.20mm guage Cum 900.00
Agra
11.20mm guage Circle/202 Cum 900.00
6.7mm guage and below 0 Dt. 01-01- Cum 850.00
3(C) STONE BOULDER (From Khera Thakur Quarry) 2020
(A) 25-40 Kg Cum 500.00
(B) 40-60 Kg Cum 525.00
(C) Stone Bricks Dressed (Size 22- 25 × 10-12 ×10-12 cm) Each 5.00
3(D) GRIT : District Gwalior MP Quarry
(Berja, chandrapura, Turak Pura, Parsen & Sumerpada)
District Bhind M.P Rates as
(Pali Dirman & Plparsana) per SE
(A) 20-40 mm Gauge Agra Circle, Cum 850.00
(B) 20 mm Gauge PWD, Agra Cum 950.00
(C) 19 mm Gauge Letter No.- Cum 950.00
14/ 2m-
(D) 16 mm Gauge Cum 950.00
Agra
(E) 13.2 mm Gauge Cum 765.00
Circle/202
(F) 11.2mm Gauge Cum 765.00
0 Dt. 01-01-
(G) 10mm Gauge 2020 Cum 765.00
(H) 5.6mm/6.7mm Gauge Cum 615.00
(I) 2.36mm Gauge/ Stone Dust Cum 615.00
4 (A) I Shaped Precast Interlocking Tiles(strength of 30MPA) at site
(i) 60 mm thick
(A) Grey Each 15.00
(B) Coloured Each 16.00
(C) Rubber Moulded Each 15.50
(D) Coloured Rubber moulded Each 16.50
(ii) 80 mm thick
(A) Grey Each 17.00
(B) Coloured Each 20.00
(C) Rubber Moulded Each 19.00
(D) Coloured Rubber moulded Each 21.00
Page 8
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
(iii) 100 mm thick
(A) Grey Each 21.00
(B) Coloured Each 23.00
(C) Rubber Moulded Each 22.00
(D) Coloured Rubber moulded Each 24.00
4(B) Rubber Moulded Cement concrete Kerb stone M-20
Size 12"×12" ×6" Each 85.00
Size 12"×16" ×6" (Plain) Each 110.00
Size 12"×16" ×6" (Designer) Each 120.00
Size 12"×18" ×6" Each 125.00
4- (C) PLAIN GLASS (Best Quality, Cut to Size)
5mm thick 19.11 Sqm 600.00
4mm thick 19.11 Sqm 500.00
3mm thick 19.11 Sqm 450.00
Note:- For Pinhead glass the rates will be 10% less than the above rates.
5- GLASS STRIPS
(A) 22mm wide- 2.8 to 3.7 mm thick RM 5.50
(B) 32mm wide 2.8 to 3.7 mm thick RM 6.50
(C ) 32mm wide, 5mm thick RM 8.60
6- LIME
(A) From Maihyer 1.2.1 Quintal 650.00
(B ) Katni IS 712.1964 Quintal 700.00
7- REINFORCEMENT & STRUCTURAL STEEL
(A) TMT Bar Fe 500- 8mm dia As per
Quintal
current price
(B) TMT Bar Fe 500- 10mm to 12mm dia list from
Quintal SAIL
(C)TMT Bar Fe 500 16mm to 32mm dia (Excluding
Quintal GST)
(D) MS Angle 226,KST,45-5 Quintal 4300.00
(E) MS Tee Quintal
IS1977KST32-0 4300.00
(F) MS Channel - 75x40MM (IS 2062 E 250 BR) Quintal 4300.00
(G) MS Channel - 100x50MM (IS 2062 E 250 BR) Quintal 3800.00
(H) M.S.Flat Iron 10.2.2.21S Quintal 4300.00
(I) M.S.Iron plate Quintal 5200.00
(J) M.S. Square Bar Quintal 4300.00
(K) MS Round /D/ Square/Rectangular HolIow Pipes/Tubes Quintal 5200.00
(L) RS Joist/ISMB Quintal 4800.00
8- MARBLE CHIPS
(A) White- Snow white Quintal 350.00
(B) White- Commercial White Quintal 250.00
(C ) Red Blood Colour Quintal 300.00
(D) Black and other Colour Quintal 300.00
9- MARBLE DUST
Marble dust (200 mesh) Quintal 250.00
10- GLAZED TILES (I.S.I. Marked or equivalent) Thickness 6 mm
(A) 300mm x 450mm size - White Piece 65.00
(B) 300mm x 450mm size- Coloured Piece 70.00
(C ) 250mm x 375mm size - White Piece 40.00
(D) 250mm x 375mm size- Coloured Piece 45.00
(E) For floor 300mm x 300mm size- White Piece 45.00
(F) For wall 200mm x 300mm size- Coloured Piece 30.00
11- COARSE SAND (Excluding actual Bulkage) 1.9
For Distt Firozabad Cum 2700.00
For Distt Mainpuri Cum 2800.00
Page 9
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
12- FINE SAND FM 1.25 (Excluding Actual Bulkage) Dholpur 1.9
For Distt Firozabad Cum 1900.00
For Distt Mainpuri Cum 2000.00
Local Sand Cum 1000.00
13- CEMENT
(A) Ordinary Portland Cement (J.P., A.C.C., Birla, J.K. or equivalent) O.P.C. 1.8 Bag(50kg) 275.00
(B) Pozzolona Portland Cement (P.P.C.) J.P., ACC Birla, JK,equivalent) Bag(50kg) 250.00
(C) White Cement (J.K. or Birla Brand) I.S. 8042-1978 Bag(50kg) 700.00
14- Surkhi 1.13 Cum 600.00
15- MARBLE/STONE TILES
(A) Marble white Alebeta 20mm (60cm x 60cm Size) Sqm 1800.00
(B) Marble white Dhungri 20mm (60cm x 60cm Size) Sqm 1550.00
(C ) Marble white Adanga 20mm (60cm x 60cm Size) Sqm 1200.00
(D) Black granite (Polished) in big slab 20mm thick Sqm 3000.00
(E) Black granite (Polished) in big slab 10mm thick Sqm 1600.00
(F) Granite (Polished) upto 0.50 Sq.M. slab 18mm thick Sqm 1750.00
(G) Granite (Polished) above 0.50 Sq.M. slab 18mm thick Sqm 1950.00
(H) Kotastone of ASI (K) 16 to 24mm thick, 60cm x 60cm Sqm 500.00
(I) Kotastone of ASI (K) 25 to 40mm thick, 60cm x 60cm Sqm 625.00
(J) Baroda green 20mm thick, (60cm x 60cm Size) Sqm 1100.00
16- PRECAST TILES
(i) Precast Terrazzo Tiles 20mm thick with gray cement
(250mm x 250mm size) Sqm 250.00
(125mm x 250mm size) Sqm 150.00
(II) Precast Terrazzo Tiles 20mm thick white cement
(250 mm x 250mm size) Sqm 260.00
(125mm x 250mm size) Sqm 160.00
(III) Chequered Terrazzo Tiles with grey cement
Sqm 260.00
(300x300mm)
BELL/KAJARIA , ROMANO, SOMANY, ORIENT, ASIAN,
17-
JOHNSON TILES.
(White Cloudy - ordinary colours)
(I) For Floor size 300 x 300mm- White I.S. 777-1970 Sqm 525.00
(II) For Wall-size 200 x 300mm - Coloured I.S. 13755-89 Sqm 500.00
(III) For Wall-size 300 x 600mm - Coloured I.S. 13755-89 Sqm 600.00
(IV) Vitrified Tiles 600 x 600mm 10MM Thick I.S. 13755-89 Sqm 650.00
(V) For Floor size 300 x 300mm- White(Anti skid tiles) I.S. 777-1970 Sqm 550.00
(VI) Vitrified Tiles 600 x 600mm 10MM Thick (Anti Skid Tiles) Sqm 700.00
18- Aluminum, DOOR FITTINGS
(A) I.S.I. Marked Aluminum Tower Bolt (With Fixers)
(I) 10mm dia 80mm long Dozen 400.00
(II) 10mm dia 100mm long Dozen 450.00
(III) 10mm dia 150mm long Dozen 550.00
(IV) 10mm dia 200mm long Dozen 680.00
(V) 10mm dia 300mm long Dozen 980.00
(B) I.S.I. Marked Aluminum Sliding Bolt with nuts & bolts.
(I) Bolt 16mm dia 20mm long Each 160.00
(II) Bolt 16mm dia 250mm long Each 180.00
(III) Bolt 16mm dia 300mm long Each 210.00
(C) I.S.I. Marked Aluminum door Handle
(I) 100 mm long Each 50.00
(II) 125mm long Each 65.00
(D) Aluminum Door Stoppers Each 65.00
Page 10
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
19- STEEL 304 GAUGE FITTINGS (I.S.I. MARKED ONLY)
(A) Steel Tower Bolt with 10mm dia rod & screw 100mm long Each 30.00
(B) Steel Tower Bolt with 10mm dia rod & screw 150mm long Each 50.00
(C ) Steel Tower Bolt with 10mm dia rod & screw 200mm long Each 60.00
(D) Steel Tower Bolt with 10mm dia rod & screw 250mm long Each 80.00
(E) Steel Tower Bolt with 10mm dia rod & screw 300mm long Each 95.00
(F) Steel Sliding Bolt with 16mm dia rod & screw 200mm long Each 75.00
(G) Steel Sliding Bolt with 16mm dia rod & screw 250mm long Each 100.00
(H) Steel Sliding Bolt with 16mm dia rod & screw 300mm long Each 105.00
(I) Steel door Handles with screw 100mm long Each 60.00
(J) Steel door Handles with screw 125mm long Each 70.00
(K) SS door Handles with screw 300mm long For Fully Glaszed
Each 1200.00
Door
Note:- For other quality less 30% on above rate.
20- MISCELLANEOUS. FITTINGS
(a) I.S.I Marked Iron Hinges
50mm long Dozen 75.00
63mm long Dozen 90.00
75mm long Dozen 95.00
100mm long Dozen 180.00
125mm long Dozen 280.00
150mm long Dozen 350.00
Male & Female hinges for M.S. Gate kg 80.00
M.S Hingage for Gate kg 75.00
(b) I.S.I Marked Steel Hinges
50mm long Dozen 120.00
63mm long Dozen 144.00
75mm long Dozen 180.00
100mm long Dozen 300.00
125mm long Dozen 420.00
150mm long Dozen 540.00
(a) Oxidized window catcher Right & Left Each 20.00
(b) Oxidized Iron Stay Each 30.00
(c) Iron Screw (Needle fold) 12mm 200 Nos 55.00
(d) Iron Screws 15mm 200 Nos 65.00
(e) Iron Screws 20mm 200 Nos 70.00
(f) Iron Screws 25mm 200 Nos 95.00
(g) Iron Screws 30mm 100 Nos 65.00
(h) Iron Screws 35mm 100 Nos 70.00
(i) Iron Screws 40mm 100 Nos 75.00
(j) Iron Screws 50mm 100 Nos 95.00
(k) Bolts & nuts upto 13mm dia Kg 80.00
(l) Above 6mm dia but upto 13mm dia Kg 85.00
(m) Above 13mm dia but upto 18mm dia Kg 95.00
(n) Bolt Type Fastener 50 mm long Each 5.00
(o) Bolt Type Fastener 75 mm long Each 7.00
(p) Pin Type Fastener 100 mm long Each 12.00
(q) Pin Type Fastener 150 mm long Each 15.00
21- PAINT & DISTEMPERS
Oil Bound Distemper (Oil paste of best quality viz, Asian, Burger, J&N)
(a) White 5 kg pack 450.00
(b) Coloured 5 kg pack 500.00
Lead White (Safeda) Per kg 130.00
Paints Synthethic Enamel Superior Quality (Asian, Burger or Equivalent) Per Litre 265.00
Page 11
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
Primer
For Wood Per Litre 165.00
For Metal (Red Oxide) Per Litre 150.00
Cement primer for interior (Asian, Burger or Equivalent) Per 20 Kg Pack 2100.00
Cement primer for Exterior (Asian, Burger or Equivalent) Per 20 Kg Pack 2400.00
Water Proof Cement Paint Per kg 60.00
Putty (Birla White/Nerolac/J.K or Equivalent) Per 20 Kg Pack 450.00
Royal shine paint or Equivalent (Plastic Paint) Per Litre 450.00
Exterior Emulsion Paint (Apex) or Equivalent Per 20 Kg Pack 4400.00
Epoxy paint ( superior quality) Per Litre 400.00
Epoxy primer Per Litre 380.00
22- IRON SHEETS
(a) Iron sheet Galvanized plain Quintal
10.22 (I.S.- 1987) -
(i) 22 gauge (0.80mm) KST 440 Quintal 6300.00
(ii) 24 gauge (0.63mm) KST 440 Quintal 6400.00
(b) Iron Sheet Galvanized Corrugated 24gauge (0.63mm) I.S.- 1852-1977 Quintal 6300.00
(c ) Iron Sheet Galvanized Corrugated 18gauge (1.25mm) 10.2.2IS1987 Quintal 6200.00
(d) M.S. Iron Sheet Plain Quintal 6100.00
(e) Galvanized Iron wire gauge (24x14) machine made Sqm 165.00
(f) Expanded metal 2.0cm. 16/17 gauge Sqm 160.00
(g) M.S. binding wire 20 gauge kg 60.00
23- MESHES
(i) Welded mesh 1" x 2" size of 10gauge wire Sqm 240.00
(ii) Welded mesh 1" x 3" size of 10 M.S. Wire Sqm 320.00
(iii) Welded mesh 2" x 2" size of 10mm gauge Sqm 170.00
(iv) Murga Jali 1/2" x 24 gauge Sqm 65.00
(v) Mosquito/Fly Proof Stainless Steel grade 304 wire mesh gauge
Sqm 480.00
with 0.50 mm dia wire and 1.40mm wide aperture.
BOARD & DOORS (I.S.I. Marked) with water Proof and Anti
24-
Termite Treated
(1) Plywood 19mm Thick Sqm 950.00
(2) Plywood 10mm Thick Sqm 830.00
(3) Plywood 6mm Thick Sqm 650.00
(4) Flush Door 30mm thick Commercial (I.S.I. Marked) Sqm 950.00
(5) Flush Door 32mm thick Commercial (I.S.I. Marked) Sqm 1050.00
(6) Flush Door 35mm thick Commercial(I.S.I. Marked) Sqm 1100.00
(7) Flush Door 30mm thick Teak (I.S.I. Marked) Sqm 1650.00
(8) Flush Door 32mm thick Teak (I.S.I. Marked) Sqm 1700.00
(9) Flush Door 35mm thick Teak (I.S.I. Marked) Sqm 1750.00
(10) Flush Door 40mm thick (I.S.I. Marked) Sqm 1300.00
(11) Fiber wood particle board 12 mm thick Sqm 425.00
(12) Veneered particle board 12mm thick Sqm 630.00
(13) Veneered particle board 20mm thick Sqm 750.00
(14) Veneered particle board (Deco.) 12mm thick Sqm 650.00
(15) Teak wood particle board 19mm thick Sqm 800.00
(16) Teak wood particle board 19mm thick (Laminated on one side) Sqm 800.00
Page 12
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
25- MISCELLANEOUS
(1) G.I. Barbed wire (Hot Dip) 10.7 (I.S. 278) Quintal 6400.00
(2) Washer (Limpet) 100 Nos 50.00
(3) Washer (Bitumen) 100 Nos 45.00
(4) Washer G.I. 100 Nos 50.00
(5) J. Hooks Kg 90.00
(6) Rope (Moonj) Kg 75.00
(7) Rope (Hemp) Kg 90.00
(8) Rope (Cotton) Kg 85.00
(9) Spun yarn 10.2.2. I.S. 1148 Kg 65.00
(10) Rivets Kg 115.00
(11) Nails (Country) Kg 125.00
(12) Nails (wire) Galvanized Kg 100.00
(13) Tarfelt Sqm 180.00
(14) Pulley (For Rolling Shutter) Each 300.00
(15) Rolling Shutter 80X0.90mm lath Sqm 1150.00
(16) Rolling Shutter 80X1.25mm lath Sqm 1525.00
(17) Hood Cover (For Rolling Shutter) RM 340.00
(18) Top Cover (For Rolling Shutter) 0.90 mm thick RM 365.00
(19) Top Cover (For Rolling Shutter) 1.25 mm thick RM 440.00
(20) Coil Spring (For Rolling Shutter) Each 450.00
(21) Ball Bearing (For Rolling Shutter) Each 300.00
(22) R.C.C. Jali 2.0 x 0.75 x 50mm Sqm 170.00
(23) R.C.C. Jali 1.25 x 0.60 x 40mm Sqm 165.00
(24) R.C.C. Jali 0.75 x 0.50 x 32mm Sqm 155.00
(25) Plaster of Paris 50 kg bag 300.00
(26) Hessian Cloth Sqm 35.00
(27) Perforated tiles 60cm x 60cm x 12mm thick for false celling Sqm 290.00
(28) Perforated decorative tiles 60cm x 60cm x 12mm thick for false
Sqm 500.00
celling
(29) Aluminum Tee- Channel 2mm thick RM 100.00
(30) Caustic Soda or Oxalic acid kg 70.00
(31) A.C. Pipe 100mm Dia 6 ft. long Each 220.00
(32) M.S. Clamp for A.C. Pipe Each 25.00
(33) Shoe for A.C. Pipe Each 60.00
(34) Holder label for A.C. Pipe Each 40.00
(35) Head including Rose for A.C. Pipe Each 60.00
(36) Bend Each 60.00
(37) Z Section for steel windows.
(38) F7-d Section @ 1.42 kg/RM 10.2.2 (I.S.227) kg 55.00
(39) F4-B/T2/T6 Section @ 2.280 kg/RM 10.2.2 (I.S.228) Kg 55.00
(40 ) F27-Section 10.2.2 (I.S.228) kg 55.00
(41) EZ-7 Section @ 1.9 kg/RM 10.2.2 (I.S.228) kg 55.00
(42) Ballies (100mm average dia) RM 60.00
(43) Water Proofing Compound ( Dr. fiixit) Litre 150.00
(44) Polish (Mainsion & Wax) 15.92 & IS 348-1968 Per kg 370.00
(45) Wood Preservator in 5 litres Drum IS218-1961 Per Litre 75.00
(46) Aldrin Concentrate Tow 0.3 ( Nosil Brand or Equivalent as per IS 1307) Per Litre 30.00
(47) Traffic cones Nos. 500.00
Page 13
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
26- Anodized Aluminum Sections
(a) 100 x 44.5 x 2mm thick kg 290.00
(b) 83.5 x 44.65 x 2mm thick kg 290.00
(c ) 114 x 44.5 x 2mm thick kg 290.00
(d)Powder Coated aluminium ( minimum thickness of powder
kg 200.00
Coating 50 micron)
(e) Aluminum Channel Beading RM 130.00
(f) Rubber Beading RM 75.00
(i) Hydraulic Floor Spring ( ISI Marked) Each 8500.00
27- Fuel wood Quintal 800.00
28- Wood
(a) U.P.Teak Wood (Cut to Size) Cum 110000.00
(b ) Sal wood (Cut to Size) Cum 80000.00
(c) Sheesham (Cut to Size) Cum 75000.00
(d) Country wood (Mango, Neem etc.) (Cut to Size) Cum 30000.00
(e) Chir/Kail wood (battens & planks) Cum 55000.00
(f) Salwood Chaukhat 100 x 65 single rebate including joint treated
with fevicol properly nailed with one coat of primer, black japan
RM 550.00
paints on wall side excluding cost of holdfast complete 100 x 65mm
Single revetted (Tolerance 3mm)
(g) Salwood Chaukhat 120 x 65 single rebate including joint treated
with fevicol properly nailed with one coat of primer, black japan
RM 700.00
paints on wall side excluding cost of holdfast complete 120 x 65mm
Double revetted (Tolerance 3mm)
29- Extra Item
(1) A.C. Sheet 6mm Corrugated Sqm 250.00
(2) A.C. Sheet Plain 4mm thick Sqm 170.00
(3) Steel curtain rod 20mm dia R.M. 65.00
(4) Steel curtain rod 25mm dia R.M. 85.00
(5) Steel Curtain rod Bracket for 20mm dia Pair 90.00
(6) Steel Curtain rod Bracket for 25mm dia Pair 120.00
(7) Fevicol SH Kg 185.00
(8) Fevicol SR Kg 310.00
(9) Hetax Kg 380.00
(10) Metal Putty 250gm packet Pkt 70.00
(11) Dori cotton average 6mm dia Kg 105.00
(12) Nails koka Kg 110.00
(13) Nails Kg 80.00
(14) Aluminium Sheet 26 gauge (0.5 mm Thick) Sqm 290.00
(15) Aluminium Sheet 24 gauge (0.63 mm Thick) Sqm 400.00
(16) Aluminium Sheet 18 gauge (1.25 mm Thick) Sqm 500.00
(17) Aluminium Sheet 16 gauge (1.5 mm Thick) Sqm 550.00
(18) Aluminium Sheet 14 gauge ( 2mm Thick) Sqm 650.00
(19) Translucent Roofing sheet (1.2 mm Thick) Sqm 600.00
(20) Sand Paper Each 11.00
(21) M-Seal 100 gm Pkt 40.00
(22) Teak wood beading size 20 x 45mm R.M. 65.00
(23) Teak wood beading size 20 x 25mm R.M. 50.00
(24) Teak wood beading size 20 x 15mm R.M. 40.00
(25) White china glazed low level cistern's 10 litre capacity with all
Each 2500.00
internal fitting of P.V.C. (Parry ware, Hindware etc.)
Page 14
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
(26) P.V.C. Low level Cistern's 10 litre capacity with all internal
Each 1300.00
fitting perryware, cert, dip last, etc.
(27) Internal fittings for china low level cistern's (Brass) Set 950.00
(28) Internal fitting for P.V.C. low level cistern's Set 425.00
(29) Anti termite treatment oil Litre 330.00
(30) Bleaching powder Kg 45.00
(31) White glazed china pedestal for wash basin Each 880.00
(32) China white glazed automatic flushing cistern's Each 1200.00
(33) C.P. Spreader for Urinals Each 450.00
(34) P.V.C. pipe 110mm dia I.S.I. Marked (working presure
R.M. 275.00
4kg/sqcm)
(35) P.V.C. pipe 90mm dia I.S.I. Marked (working presure
R.M. 170.00
4kg/sqcm)
(36) P.V.C. pipe 75mm dia I.S.I. Marked (working presure
R.M. 130.00
4kg/sqcm)
(37) P.V.C. pipe 50mm dia I.S.I. Marked (working presure
R.M. 100.00
4kg/sqcm)
(38) P.V.C. Bend 110mm dia I.S.I. Marked Each 70.00
(39) P.V.C. Bend 90mm dia I.S.I. Marked Each 60.00
(40) P.V.C. Bend 75mm dia I.S.I. Marked Each 55.00
(41) P.V.C. Bend 63mm dia I.S.I. Marked Each 50.00
(42) P.V.C. Reducing Bend 110/90 mm dia I.S.I. Marked Each 65.00
(43) P.V.C. Reducing Bend 90/63 mm dia I.S.I. Marked Each 60.00
(44) P.V.C. T 110 mm dia I.S.I. Marked Each 175.00
(45) P.V.C. T 90 mm dia I.S.I. Marked Each 150.00
(46) P.V.C. Reducing T 110/90 mm dia I.S.I. Marked Each 125.00
(47) P.V.C. Reducing T 90/63 mm dia I.S.I. Marked Each 100.00
(48) P.V.C. Socket 110mm dia I.S.I. Marked Each 45.00
(49) P.V.C. Socket 90mm dia I.S.I. Marked Each 35.00
(50) P.V.C. Socket 63mm dia I.S.I. Marked Each 30.00
(51) P.V.C. Socket 50mm dia I.S.I. Marked Each 25.00
(52) P.V.C. Reducing Socket 110/90 mm dia I.S.I. Marked Each 40.00
(53) P.V.C. Reducing Socket 90/63 mm dia I.S.I. Marked Each 35.00
(54) P.V.C. Y Type 110 mm dia I.S.I. Marked Each 175.00
(55) P.V.C. Pipe's jointing solution (Tube) 100 gm Each 25.00
(56) P Trap Each 110.00
(57) S Trap Each 120.00
(58) Steel sink 600 x 450 x 200mm (ISI Mark)
(a) Without Drainage board Each 2800.00
(b) With Drainage Board Each 3200.00
(59) Stainless Steel sink with drainage Board 610x450x250mm
Each 4000.00
1mm thick (salem steel, ISO 9002)
(60) Marble sink 24" x 18" x 18" Each 1500.00
(61) P.V.C. Water Storage Tank Syntex or Equivalent Litre 8.00
(62) Brass Spindle for C.P. Pillar Cock Each 105.00
(63) Steel Pipe 20mm dia ( 304 Grade) kg 220.00
(64) Steel Pipe 25mm dia ( 304 Grade) kg 220.00
(65) Steel Pipe 50mm dia (304 Grade) kg 220.00
(a) 125 Micron plastic sheet. Sqm 25.00
30-
(b) 125 Micron plastic sheet for bowel bars Sqm 30.00
31- Cost of Water KL 60.00
32- Pre-moulded Joint filler, 25 mm thick for expansion joint Sqm 430.00
Page 15
Schedule PWD Rate in
MATERIALS Unit
Item No. Spec. No. Rs.
33- Joint sealant kg 180.00
34- Sealant primer kg 120.00
35- Curing Compound Litre 65.00
36- Debonding Strip black, white RM 4.75
Super plasticizer admixture IS marked as per SI.9103-1999/2003
37- kg 65.00
Note:-
1 Rates of all Material as above are Inclusive of Contractor Profit except Item No.
1,2,3,9,11,12 & 13
2 5% Contractor profit on Item No. 1,2,3,9,11,12 & 13 may be given while taking the
supply through some agency other than direct supplier.
3 G.S.T is not Included in the given rates.
4 The above rates are inclusive of octori, royality Zila parishad, Toll Tax and all other
Taxes etc Complete But Excluding Forest Transit Fees.
5 The rates for item are No.-1,2 (Bricks & Brick Ballast) are at kiln including cartage
upto 8th km. Loading unloading stacking, royality, Zila parishad,Toll Tax and all
other Taxes but Excluding GST.
6 R.M.R must be approved by competent authority.
7 The rates for stone ballast,grit,Cut Stone,Boulder etc. are fixed Quarries Loaded in to
Trucks.The material should be peurchased from nearest approved Quarries.
8 Latest Cartage rates for material shall be applicable, as approved by S.E, Lucknow
circle, P.W.D Lucknow.
9 Transpotation Charges for Item No. 39 @15% Upto distance 100 km and beyond 100
km 18 % of the cost of goods.
Page 16
CHAPTER-2
Labour Rate
Rate in
Sl. No. Description of Labour Unit
Rs.
1- Mistri/Mason (First Class) Per Day 500.00
2(a)- Mason (for floor & Tiles Work) Per Day 475.00
2(b)- Mason (for other works) Per Day 425.00
3(a)- Carpenter (for skilled/furniture work) Per Day 450.00
3(b)- Carpenter (for other work) Per Day 425.00
4- Black Smith Per Day 450.00
5- Hammer Man Per Day 350.00
6- Fitter Per Day 425.00
7- Welder Per Day 450.00
8(a)- Painter (for Polishing Work) Per Day 450.00
8(b)- Painter (for Painting work) Per Day 420.00
9- Plumber (Licensed with kit) Per Day 475.00
10- Helper to Plumber Per Day 330.00
11- Mate/Agent/Bandhani Per Day 330.00
12- Mazdoor (skilled) / Beldar / Chawkidar / Helper / Cleaner Per Day 320.00
12(a)- Mazdoor (Semi Skilled) Per Day 310.00
13- Coolies/Mazdoor( unskilled) Per Day 300.00
14- Bhisti with Mashak Per Day 340.00
15- White Washer Per Day 325.00
16- Beldar for bitumen/tar work Per Day 325.00
17- Two donkey with driver Per Day 800.00
18- Glazier Per Day 400.00
19- Floor cutting machine with operator but without grinding stone Per Day 800.00
20- Tractor with trolley including P.O.L. & Driver Per Day 1600.00
20(a)- Road Roller Without P.O.L. & Driver Per Day 1400.00
20(b)- Road Roller With P.O.L. & Driver etc Per Day 2500.00
21- Rivetter Per Day 400.00
Driver for Jeep / Car / Truck / Tipper / Roller , Operator for Pump / Mixol /
22- Per Day 450.00
Generator , Electrician / Wire man.
23- Mallah Per Day 320.00
24(a)- Sweeper (Full Time) Per Day 350.00
24(b)- Sweeper (Part Time) Per Day 250.00
25- Ameen/Tracer Per Day 400.00
26- Surveyor/Draftman Per Day 550.00
27- Tractor with Water Tanker with cost of water Per Day 1600.00
28- Mixol Machine Complete in all respect (without P.O.L.) Per Day 1800.00
C.C. Mixer with Hopper, One Cement bag Capacity, with POL and Operator
29- Per Day 2100.00
Complete in all respect
Water Tanker with Sprinkler 6000 Litre or above cap.With POL/Driver
30- including filling of water etc. complete. Per Day 1900.00
31- J.C.B. (Joint Cutter Bucket) Including P.O.L. and Driver Per Hour 1000.00
32- Vibrator (Surface/Pin with Operator and POL Per Day 800.00
33- Armed Guard from security agency. Per Day 400.00
34- Cook Per Day 400.00
35- Gardener Per Day 325.00
36- Farras Per Day 325.00
37- Waiter Per Day 325.00
Page 17
Rate in
Sl. No. Description of Labour Unit
Rs.
Five door commercial vehicle with driver having taxi permit without fuel.
38-(a) Per Day 950.00
(Jeep/Bolero)
Five door commercial vehicle with driver having taxi permit without fuel.
38- (b) Per Day 1000.00
(TUV/Scorpio/Innova)
39- Data entry Operator (without C.P) Per Month 20500.00
For Bridge Work Only ;-
40- Masson (very skilled) Per Day 600.00
41- Blacksmith (very skilled) Per Day 650.00
42- Welder (very skilled) Per Day 600.00
43- Sinker (very skilled) Per Day 600.00
44- Sinking Helper (skilled) Per Day 500.00
45- Labour (very skilled) Per Day 360.00
46- Mate (very skilled) Per Day 600.00
47- For heavy machines Per Day 750.00
48- Driver for heavy machines like cranes Per Day 1050.00
mijksDr Jfed njsa dsoy vkx.ku gsrq ekU; gSA
Page 18
CHAPTER-3
CARTAGE
Page 19
Page 20
Page 21
Page 22
CHAPTER-4
EARTH WORK
Sl. Schedul Description of the Work PWD Unit Over all
No. e Item Specification Rate
No. No.
1 251 Excavation in foundation in ordinary soil (Loam, Clay or Sand) 4.1.1
including lift upto 1.50 m and lead upto 30m and including filling
watering and ramming of excavated earth into the trenches or into
the space between the building and the sides of foundation
trenches or into the plinth and removal and disposal of surplus
earth as directed by the Engineer In-charge upto a distance of 30m
from the foundation trenches.
Cum 135.00
2 252 As in Item 251 above, but excavation in soil mixed with moorum 4.1.3
shingle kankar requiring the use of special tools and Plants such
as pick axes subbals etc. Cum 140.00
3 253 Earth work in cutting or in embankment in ordinary soil -
excavation to be in the form of a regular pits not exceeding 0.50m
in depth and earth work in embankment to be in 20cm layers
including ramming and dressing the surface to required levels and
slopes and also including 1.5 m lift and 30m lead. The earth in
form of cutting to be used as spoil banks within 50m distance as
directed by the Engineer-in-Charge.
Cum 120.00
4 253(a) Extra cost for Earth work in embankment mechanically compacted -
to 95% proctor density In ordinary soil, excavation to be done form
of regular pits not exceeding 0.5mtr in depth and work in
embankment to be in 20cm layer including ramming and dressing
pulverization surfacing including Supply of Labour, T&P, Roller
and water sprinkler etc. Cum 30.00
5 253(b) Extra for Earth work in embankment mechanically compacted to -
100% proctor density In ordinary soil, excavation to be done form
of regular pits not exceeding 0.5mtr in depth and work in
embankment to be in 20cm layer including ramming and dressing
pulverization surfacing including Supply of Labour, T&P, Roller
and water sprinkler
Cum 35.00
6 253(c) Add Extra on Item No. 253 above for 1 km cartage Earth - Cum 40.00
7 253(d) Add Extra on Item No. 253 above for 3 km cartage Earth - Cum 75.00
8 253(e) Add Extra on Item No. 253 above for 5 km cartage Earth - Cum 105.00
9 254 Add to Item (251-252) to every additional 30m lead or part of 30m -
(100ft) or for every additional 1.5m (5ft) lift or part of 1.5m (5ft)
Cum 20.00
10 255 Sand filling in plinth including supply of necessary quantity of 4.4
local sand from a distance not exceeding 8 Kms from the site of
work and including watering dressing etc. required for proper
completion of work Cum 1300.00
11 259 Cleaning Jungles including uprooting of rank vegetation grass, -
bushes, wood trees and sapling of girth upto 30cm measured at a
height of 1 meter above ground level and removal of rubbish upto a
distance of 50 meters out side the periphery of area cleared.
Sqm 5.50
Note For new construction of widening and strengthening & Bridge works analyised Rates
s-1 (MORTH/MORD) shall be applicable
Page 23
CHAPTER-5
CONCRETE WORK
PWD/C
DSR/
Sl. PWD LABOUR Over all
PWD SI Description of the Work Unit
No. Spec. RATE Rate
No
No.
1- 273 Providing and laying cement concrete in 1:6:12 (1 cement : 6 5.4.1
Coarse sand : 12 graded stone aggregate 40mm nominal
size) including supply of all materials, labour and T&P etc.
required for completion of work and curing complete,
including cost of form work. In Foundation and floors.
Page 24
PWD/C
DSR/
Sl. PWD LABOUR Over all
PWD SI Description of the Work Unit
No. Spec. RATE Rate
No
No.
10 5.1 RCC work Providing and laying in position specified grade of 5.1.2
reinforced cement concrete in Raft foundation, including the
cost of centering, shuttering, finishing and excluding
reinforcement - All work up to plinth level in :1:1.5:3 (1
cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm
nominal size)
Cum 1150.00 7950.00
11 5.1 RCC work Providing and laying in position specified grade of 5.1.2
reinforced cement concrete,Slab including the cost of
centering, shuttering, finishing and excluding reinforcement -
Above plinth level upto fifth floor level in :1:1.5:3 (1 cement :
1.5 coarse sand : 3 graded stone aggregate 20 mm nominal
size)
Cum 1150.00 8450.00
12 5.2 Reinforced cement concrete work in walls (any thickness), 5.2.2
including attached pilasters, buttresses, plinth and string
courses, fillets, columns, pillars, piers,abutments, posts and
struts etc. including cost of centering, shuttering, finishing
and excluding reinforcement :1:1.5:3 (1 cement : 1.5 coarse
sand : 3 graded stone aggregate 20 mm nominal size)
Page 25
CHAPTER-6
BRICK WORK
Cum - 400.00
6 6.13 Add extra to Item No. 1 to 4 above for super structure 6.13.1
above plinth level upto floor five level including
necessary cutting and moulding of brick work as
required and also including honeycombed brick work
in thickness of wall 12cm and less.
Cum - 530.00
7 - Add extra to Item No. 1 to 4 above but in super -
structure above plinth level upto floor five level
including necessary cutting and moulding of brick
work as required and also including honey combed
brick work in thickness of wall 8cm and below.
Cum - 570.00
Page 26
CHAPTER-7
DAMP PROOF COARSE
PWD
Sl. DSR/PW LABOUR Over all
Description of the Work Spec. Unit
No. D Sl.No. RATE Rate
No.
1 360 2 Cm thick D,.P.C with Cement and approved -
coarse sand 1:2 and including water proofing
materials as approved by the Engineer in Charge in
the proprortion as specified but the manufacture
including supply of all material, labore T&P for
proper completion of he work. Including proper
curing and shuttering as necessary.
Sqm 55.00 300.00
2 361 Providing and laying D.P.C 2.50 cm thick with -
Cement concrete Consisting of One Part Cement
1.5 part of Coarse Sand and three part of approved
10 mm graded Stone grit and including water
proofing martreial as approved by the Engineer-In-
Charge in the proportion as specified by
manufacturer.
Sqm 80.00 375.00
3 362 Painting on D.P.C. or Roof slab with two coats of -
air blown bitumen 60/70 or 80/100 1.7Kg/Sqm
approximate including cost of fuel if any.
Sqm 35.00 150.00
4 4.10 Providing and laying damp-proof course 40 mm 4.1
thick with cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 12.5 mm
nominal size). Including supply of all materials,
water proofing compound, labour T&P etc.
complete.
Sqm 85.00 325.00
5 4.1.3 Providing and laying damp-proof course 25 mm 4.1.3
thick with cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 12.5 mm
nominal size) including supply of all materials,
water proofing compound, labour T&P etc.
complete.
Sqm 80.00 220.00
6 4.13 Providing & applying a coat of residual petroleum 4.13
bitumen of grade VG-10 of approved quality using
1.7kg per square metre on damp proof course after
cleaning the surface with brushes and finally
with piece of cloth lightly soaked in kerosene oil.
Page 27
CHAPTER-8
ANTI TERMITE TREATMENT
SCH
Sl. LABOUR
PWD Description of the Work Unit Over all Rate
No. RATE
No
Page 28
CHAPTER-9
DOORS & WINDOWS
PWD/
PWD/ CPWDS LABOUR Over All
Sl.
DSR SI Description of the Item peci- Unit RATE Rate
No.
No fication (Rs) (Rs)
No.
1 2 4 3 5 6 7
1 401 C.P. teak wood wrought framed and fixed including simple
mouldings, straight works as in Chaukhats, including
supply of all materials, labour and T&P etc. required for
proper completion of work. Cum 120000.00
2 402 As in Item no.-401 but for Sheesam wood Cum 90000.00
3 403 As in Item no.-401 but for Indian Sal wood Cum 85000.00
4 409 Supply and fixing of 4.5cm (1.3/4") thick C.P. Teak wood
part panelled & part glazed door and window shutters
including supply of wooden cleats and stops and including
fixing and adjustment of hinses, bolts, locks, handles,
springs and/or other fitting but excluding their supply and
including painting with two coats of Black Japan on all
iron fittings if necessary & including fixing the glass panes
with putty & brad. Glass to be 4mm thick. Fitting with
necessary screws to be supplied departmently.
Sqm 6000.00
5 410 Additional cost for fixing glass panes with C.P. Teak wood
beading and felt as directed by Engineer-in-charge instead
of putty and brad including cost of all materials, labour
and T&P etc. required for proper completion of work.
Sqm 425.00
6 411 As in Item no.-409 above but fully panelled Sqm 6800.00
7 412 As in Item no.-409 above but fully glazed Sqm 5500.00
8 413 As in Item no.-409 above but 3.8cm thick Sqm 5000.00
9 414 As in Item no.-411 above but 3.8cm thick Sqm 5300.00
10 415 As in Item no.-412 above but 3.8cm thick Sqm 5000.00
11 422 As in Item no.-409 above but 3.8cm thick Sheesam wood
Sqm 4400.00
12 423 As in Item no.-411 above but 3.8cm thick Sheesam wood
Sqm 4800.00
13 424 As in Item no.-412 above but 3.8cm thick Sheesam wood
Sqm 4400.00
14 New Provinding and fixing glass panes with putty and glazing
clips in steel doors, windows,clerestory windows all
complete with : 4.0 mm thick panes.
Sqm 600.00
15 450 Supply and fixing of 4cm (3/2") thick C.P. Teak wood door
and window shutters with panels of heavy quality
galvanized iron wire gauge 2.5mm or 2mm or 1.5mm
(1/10 or 1/12 or 1/6 inch) mesh or any other size with
necessary beading including supply and fixing of wooden
cleats and stops and including fixing and adjustment of
hinses, bolts, locks, handles, springs and/or other fitting
but excluding their supply and including painting with two
coats of Black Japan on all iron fittings if necessary.
Fitting with necessary screws to be supplied departmently.
Sqm 4000.00
16 451 As in Item no.-450 above but in Sheesam wood Sqm 2000.00
Page 29
PWD/
PWD/ CPWDS LABOUR Over All
Sl.
DSR SI Description of the Item peci- Unit RATE Rate
No.
No fication (Rs) (Rs)
No.
1 2 4 3 5 6 7
17 455 Supply and fixing galvanized mosquitos proof heavy
quality iron wire gauge or expended metal heavy quality
over windows and including supply of C.P. Teakwood
batten 8cmX1cm (3"X3/8")/flat iron 25mmX4mm and
including supply of necessary screws all materials, labour,
T&P etc. required for proper completion of work.
Sqm 400.00
18 455 (a) As Item No. 455 above but with fly and mosquito proof 9.7.8
stainless steel grade 304 wire mesh gauge with 0.50mm
dia wire and 1.40mm wide aperture. Sqm - 600.00
19 456 As in Item no.-455 above but with Sheesam wood battens
Sqm 410.00
20 456 (b) As Item No. 456 above but with fly and mosquito proof
stainless steel grade 304 wire mesh gauge with 0.50mm
dia wire and 1.40mm wide aperture. Sqm 510.00
21 457 As in Item no.-455 above but with Indian Sal wood battens
Sqm 425.00
22 457 (a) As Item No. 457 above but with fly and mosquito proof
stainless steel grade 304 wire mesh gauge with 0.50mm
dia wire and 1.40mm wide aperture. Sqm 535.00
23 10.29.2 Provinding and fixing fly proof wire gauze to
windows,Clerestory wondows & doors with M.S flat 15x3
mm and nuts & bolts complete. Stainless steel (grade 304)
wire gauze of 0.5 mm dia wire and 1.4 mm aperture in
both sides.
Sqm 428.00
24 470 Supply and fixing of flush doors, commercial quality
conforming of I.S. 2202 part-1 (1983) including ISI
marked oxidized iron fitting with screws, Bolt
Hinges,Handles,Siliding bolt, Door Stopper and tower bolt
etc.
Page 30
PWD/
PWD/ CPWDS LABOUR Over All
Sl.
DSR SI Description of the Item peci- Unit RATE Rate
No.
No fication (Rs) (Rs)
No.
1 2 4 3 5 6 7
28 9.23 Same as Itme No-22 & 25 add Extra for providing lipping
with 2nd class teak wood battens 25 mm minimum depth
on all edges of flush door shutters (over all area of door
shutter to be measured).
Sqm 330.00
29 9.24 Same as Itme No-22 & 25 add Extra for providing vision 9.24.1
panel not exceeding 0.1 sqm in all type of flush doors (cost
of glass excluded) (overall area of door shutter to be
measured) :
Rectangular or square Sqm 140.00
30 9.120 Providing and fixing factory made panel PVC door shutter 9.120.1
consisting of frame made out of M.S. tubes of 19 gauge
thickness and size of 19 mm x 19 mm for styles and 15x15
mm for top & bottom rails. M.S. frame shall have a coat of
steel primers of approved make and manufacture . M.S.
frame covered with 5 mm thick heat moulded PVC 'C'
channel of size 30 mm thickness, 70 mm width out of
which 50 mm shall be flat and 20 mm shall be tapered in
45 degree angle on both side forming styles and 5 mm
thick, 95 mm wide PVC sheet out of which 75 mm shall be
flat and 20 mm shall be tapered in 45 degree on the inner
side to form top and bottom rail and 115 mm wide PVC
sheet out of which 75 mm shall be flat and 20 mm shall be
tapered on both sides to form lock rail. and lock rails shall
be provided both side of the panel. 10 mm (5 mm x 2 )
thick, 20 mm wide cross PVC sheet be provided as gap
insert for top rail & bottom rail. paneling of 5 mm thick
both side PVC sheet to be fitted in the M.S. frame welded/
sealed to the styles & rails with 7 mm (5 mm+2 mm) thick
x 15 mm wide PVC sheet beading on inner side, and joined
together with solvent cement adhesive. Top, bottom and
lock rails shall be provided both sides of the panel. 10 mm
(5 mm x 2 ) thick, 20 mm wide cross PVC sheet be
provided as gap insert for top rail & bottom rail. paneling
of 5 mm thick both side PVC sheet to be fitted in the M.S.
frame welded/ sealed to the styles & rails with 7 mm (5
mm+2 mm) thick x 15 mm wide PVC sheet beading on
inner side, and joined together with solvent cement
adhesive. An additional 5 mm thick PVC strip of 20 mm
width is to be stuck on the interior side of the 'C' Channel
using PVC solvent adhesive etc. complete as per direction
of Engineer-in-charge, manufacturer’s specification &
drawing. Sqm 1900.00
Page 31
PWD/
PWD/ CPWDS LABOUR Over All
Sl.
DSR SI Description of the Item peci- Unit RATE Rate
No.
No fication (Rs) (Rs)
No.
1 2 4 3 5 6 7
31 9.127 Providing & Fixing 1.00mm thick decorative high 9.127.2
pressure laminated sheet of plain / wood grain in gloss /
matt / suede finish with high density protective surface
layer and reverse side of adhesive bonding quantity
conforming to IS : 2046 Type S, including cost of adhesive
of approved quality.
Sqm 190.00 530.00
32 21.1 Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/ appropriate Z sections and other
sections of approved make conforming to IS: 733 and IS:
1285, fixing with dash fasteners of required dia and size,
including necessary filling up the gaps at junctions, i.e. at
top, bottom and sides with required EPDM rubber/
neoprene gasket etc. Aluminium sections shall be smooth,
rust free, straight, mitred and jointed mechanically
wherever required including cleat angle, Aluminium snap
beading for glazing / paneling, C.P. brass / stainless steel
screws, all complete as per architectural drawings and the
directions of Engineer-in-charge. (Glazing, paneling and
dash fasteners to be paid for separately) :For shutters of
doors, windows & ventilators including providing and
fixing hinges / pivots and making provision for fixing of
fittings wherever required including the cost of EPDM
rubber / neoprene gasket required (Fittings shall be paid
for separately).
Page 32
PWD/
PWD/ CPWDS LABOUR Over All
Sl.
DSR SI Description of the Item peci- Unit RATE Rate
No.
No fication (Rs) (Rs)
No.
1 2 4 3 5 6 7
37 21.18 Providing and fixing 12 mm thick frameless toughened 21.18
glass door shutter of approved brand and manufacture,
including providing and fixing top & bottom pivot & spring
type fixing arrangement and making necessary holes etc.
for fixing required door fittings, all complete as per
direction of Engineer-in-charge (Door handle, lock and
stopper etc.to be paid separately).
Sqm 3400.00
38 New Supply and fixing of anodized aluminium door having
2mm thick aluminium section excluding coating and
average coating of 20 microns fully glazed made of
aluminium door tube size 83.5x44.65 m as vertical
member and 1140x44.45 mm size tube in bottom and
horizontal member door chaukhat should be of aluminium
tublar vertical with two openable shutter, the rate will
include cost of material fixtures 4mm glass handles locks
screw necessary bending and excluding cost of floor spring
if required for proper completion of the work as per
direction of Engineer-In-Charge.
Sqm 4500.00
(A) Same as above but with 5mm thick plain glass Sqm 4600.00
(B) Same as above but for fixed glazing Sqm 4200.00
Page 33
CHAPTER- 10
MILD STEEL AND IRON WORK
PWD/
Sl. Over All
DSR/PW CPWD LABOUR
No Description of the Work Unit Rate
D SI No Spec. RATE
. (Rs)
No.
1 502 Mild steel and iron work of small size and section such 10.21
as holding down woods, hold fasts tierods, grating, etc.
(When not included in and over all rates) brought to
required form including supply of steel and its wastage
including cost of bolts, nuts if required for proper
completion of work including fabrication of holes in
door chaukhats and nosing.
Kg 25.00 65.00
2 503 Mild steel or iron work in heavy sizes such as built up 10.22
gates record rack, roof work, gates etc. brought to
required form including drilling holes revitting or
welding where necessary, and also including supply of
steel bolts, nuts, wastage etc. and their fixing require
for proper completion of the work.
Kg 25.00 65.00
3 504 Mild steel or iron work in plain work such as reinforced
concrete or reinforced brick work (When not included
in and an over all rates) brought to required shape as
necessary including bending for proper completion of
the work and excluding the supply of steel and its
wastage Bend, hooks and authorized over lapping shall
be measured upto floor to level.
(1) 6mm
Qtl. 1800.00 As per current
(2) 10mm to 12mm tor price list from
Qtl. 1800.00 SAIL
(3) 15mm to 32mm tor (Excluding
Qtl. 1800.00 GST)
NOTE:- An increase of Rs. 7.00 per floor will be
allowed after floor two levels. Labour rate does not
include cost of binding wire and other materials
Sq.M. 2500.00
5 521 Providing and fixing 27.52 cm long wire spring grade 2 10.121
for rolling shutters. Each 600.00
6 522 Providing and fixing top cover for rolling shutters made 10.16
of 18 gauge M.S. sheet. RM 650.00
7 523 Providing and fixing ball bearing for rolling shutters. 10.17
Each 400.00
Page 34
PWD/
Sl. Over All
DSR/PW CPWD LABOUR
No Description of the Work Unit Rate
D SI No Spec. RATE
. (Rs)
No.
8 524 Extra add pf S.I. No. 520 for providing mechanical
device, chain and crank operation for rolling shutters.
(A) Shutter above 11.2 Sq.M. (120 sft) but upto 16.8
Sq.M. (180 sft) area. Sqm 1000.00
(B) Shutter above 16.80 Sq.M. (180sft) area. Sqm 1100.00
9 11.14 Fixing to steel or wooden chaukhats in position.
(A) Door chaukhats/window chaukhats above 1.5
Sq.m. and upto 5 Sq.M. Each 125.00 135.00
(B) Window chaukhats above 1.5 Sq.M. Each 90.00 100.00
(C) Ventilator chaukhats Each 55.00 75.00
(D) Staircase nosing. Each 50.00 55.00
10 513 Providing GI barbed Wire (Hot Dip) iron wire fencing in 10.7
three rows including fixing it to post after stretching it
including labour and tools and plants etc. required for
proper completion of the work also including supply of
wires (14X14 SWG) with 100mm Barb Spacing (@
11.66m per Kg Wt) and excluding supply of posts.
RM 10 29.00
11 Pressed steel chaukhat
Supply of M.S. Steel 18 gauge (1.25mm) pressed steel
door chaukhat including S/F of iron hinges of 100x3
mm I.S.I. Mark with drilling holes for L-drop and pipes
15x12mm cleats for tower bolt and 40x6 mm hold fast
230mm long including supply of all materials labour
T&P carriage upto site required for proper completion
of work as per direction of E/IC.
Page 35
PWD/
Sl. Over All
DSR/PW CPWD LABOUR
No Description of the Work Unit Rate
D SI No Spec. RATE
. (Rs)
No.
16 New Providing and fixing stainless steel ( Grade 304) 10.28
railing made of Hollow tubes, channels, plates etc.,
including welding, grinding, buffing, polishing and
making curvature (wherever required) and fitting the
same with necessary stainless steel nuts and bolts
complete, i/c fixing the railing with necessary
accessories & stainless steel dash fasteners , stainless
steel bolts etc., of required size, on the top of the floor
or the side of waist slab with suitable arrangement as
per approval of Engineer in-charge, ( for payment
purpose only weight of stainless steel members shall
be considered excluding fixing accessories such as
nuts, bolts, fasteners etc.).
kg 75.00 290.00
17 New Providing and fixing stainless steel ( Grade 202)
railing made of Hollow tubes, channels, plates etc.,
including welding, grinding, buffing, polishing and
making curvature (wherever required) and fitting the
same with necessary stainless steel nuts and bolts
complete, i/c fixing the railing with necessary
accessories & stainless steel dash fasteners , stainless
steel bolts etc., of required size, on the top of the floor
or the side of waist slab with suitable arrangement as
per approval of Engineer in-charge, ( for payment
purpose only weight of stainless steel members shall
be considered excluding fixing accessories such as
nuts, bolts, fasteners etc.).
kg 75.00 190.00
18 New Mild Steel Iron 'Z' section windows and ventilators
excluding cost of glass panes of but including supply of
all materials,its fabrication, nuts and bolts, holdfast,
labour and T&P required for proper completion of
work as per direction of Engineer-in-charge and also
including cost of handles,stays etc, in all respect at site
of work. 75.00
kg 25.00
19 New Mild Steel Iron 'Z' section windows and ventilators
excluding cost of glass panes of but including supply of
all materials,its fabrication, nuts and bolts, holdfast,
labour and T&P required for proper completion of
work as per direction of Engineer-in-charge and also
including cost of handles,stays etc, in all respect at site
of work.
kg 25.00 65.00
20 New Mild Steel Iron Grill & Staircase railing of a approved
qualitiy and drawing including supply of all materials,
fabrication, labour, T&P in all respect as per direction
of Engineer-in-charge for proper completion of work at
site. kg 25.00 65.00
21 New Supply and fixiing ward robe shutters made of 18
gauge (1.25 mm) M.S sheets including cold rolling of
required shape and including supply & fixing of
approved qualitiy locks handle etc. Complete including
supply of all material labour and T&P spray painting
etc. complete Sqm - 3000.00
Page 36
CHAPTER- 11
ROOF WORK
PWD/
PWD/D Over All
Sl. CPWD LABOUR
SR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
1 538 Supply and laying complete 4cm (1-1/2") thick insulation layer of 11.9
sand and clay over jack arch, reinforced brick or reinforced
cement concrete roof.
Sqm - 35.00
2 539 Making expansion and contraction joint in terraced roof lip type, 11.10
including supply of necessary quantity of filler, tarfelt, brick tile
all material labour, tool and plants etc required for proper
completion of the work. RM - 140.00
3 540 As in Item (539) above but parapet type. 11.11 RM 75.00 525.00
4 543 Screening overleaky roof with bitumen @ 1/2 kg per Sq.M. 11.12
including sweating, cleaning the roof with brush, heating of the
paint upto the required temperature pouring it on the surface
spreading necessary qty. of approved coarse sand @ 0.30 Cu.M.
per 100 Sq.M. (1 cft per 100 sft) and including supply of all
material, labour, tool and plants etc. required proper completion
of work.
Sqm 15.00 70.00
5 544 Supplying and laying one layer of tarfelt or any other equivalent 11.13
approved material at the junction of wall and roof or at any place
as per direction of E/I including necessary over lap giving one
coat of approved mastic paint below the tarfelt and including
supply of all material labour and tools and plants etc. required for
proper completion of work fixed as per standard.
Page 37
PWD/
PWD/D Over All
Sl. CPWD LABOUR
SR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
8 12.15 Painting top of roofs with bitumen of approved quality @ 12.15.1
17kg per 10 sqm impregnated with a coat of coarse sand at 60
cudm per 10 sqm, including cleaning the slab surface with
brushes and finally with a piece of cloth lightly soaked in
kerosene oil complete with residual type petroleum bitumen of
grade VG -10
Sqm 25.00 110.00
9 22.7 Providing and laying integral cement based water proofing treatment 22.7
including preparation of surface as required for treatment of roofs,
balconies, terraces etc consisting of following operations: (a) Applying
a slurry coat of neat cement using 2.75 kg/sqm of cement admixed
with water proofing compound conforming to IS. 2645 and
approved by Engineer-in-charge over the RCC slab including
adjoining walls upto 300 mm height including cleaning the surface
before treatment.
(b) Laying brick bats with mortar using broken bricks/brick bats 25
mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5
coarse sand) admixed with water proofing compound conforming
to IS : 2645 and approved by Engineer-in-charge over 20 mm
thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand
) admixed with water proofing compound conforming to IS : 2645 and
approved by Engineer-in-charge to required slope and treating
similarly the adjoining walls upto 300 mm height including rounding
of junctions of walls and slabs.
(c) After two days of proper curing applying a second coat of cement
slurry using 2.75 kg/ sqm of cement admixed with water
proofing compound conforming to IS : 2645 and approved by
Engineer-in-charge.
(d) Finishing the surface with 20 mm thick jointless cement mortar of
mix 1:4 (1 cement :4 coarse sand) admixed with water proofing
compound conforming to IS : 2645 and approved by Engineer-in-
charge including laying glass fibre cloth of approved quality in top
layer of plaster and finally finishing the surface with trowel with neat
cement slurry and making pattern of 300x300 mm square 3 mm
deep.
(e) The whole terrace so finished shall be flooded with water for a
minimum period of two weeks for curing and for final test.“All above
operations to be done in order and as directed and specified by the
Engineer-in-Charge : With average thickness of 120 mm and
minimum thickness at khurra as 65mm.
Sqm 200.00 1000.00
10 12.1
Providing corrugated G.S. sheet roofing including vertical / curved
surface fixed with polymer coated J or L hooks, bolts and nuts 8
mm diameter with bitumen and G.I. limpet washers or with G.I.
limpet washers filled with white lead, including a coat of approved
steel primer and two coats of approved paint on overlapping of
sheets complete (up to any pitch in horizontal/ vertical or curved
surfaces), excluding the cost of purlins, rafters and trusses and
including cutting to size and shape wherever required.
1.00 mm thick with zinc coating not less than 275 gm/m² 12.1.1 Sqm 130 1000.00
0.80 mm thick with zinc coating not less than 275 gm/m² 12.1.2 Sqm 130 860.00
0.63 mm thick with zinc coating not less than 275 gm/m² 12.1.3 Sqm 130 745.00
11 12.4 Providing ridges or hips of width 60 cm overall width plain G.S. 12.4.2
sheet fixed with polymer coated J or L hooks, bolts and nuts 8
mm dia G.I. limpet and bitumen washers complete. (0.63 mm
thick with zinc coating not less than 275 gm/m²). 508.00
RM
Page 38
PWD/
PWD/D Over All
Sl. CPWD LABOUR
SR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
12 22.90 Providing and laying six courses water proofing treatment with 22.9
bitumen felt over roofs consisting of first, third and fifth course of
blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot
@ 1.45, 1.20 and 1.45 Kg per square metre of area respectively,
second and fourth courses of roofing felt type 3 grade I
conforming to IS : 1322 (Hessian based self finished bitumen felt)
, sixth and final course of stone grit 6 mm and down size or pea
sized gravel spread at 6 cubic decimeter per sqm including
preparation of surface but excluding grading, complete.
Page 39
PWD/
PWD/D Over All
Sl. CPWD LABOUR
SR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
18 12.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 12.21.1
coarse sand : 4 stone aggregate 10 mm and down gauge),
including finishing with cement mortar 1:3 (1 cement : 3 fine
sand) as per standard design : In 75x75 mm deep chase.
RM 75.00 135.00
19 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain 12.41.2
water pipes conforming to IS : 13592 Type A, including jointing
with seal ring conforming to IS : 5382, leaving 10 mm gap for
thermal expansion,
(i) Single socketed pipes.110 mm diameter.
RM 55.00 375.00
Page 40
CHAPTER- 12
CEILING AND LINING
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
1 New Providing and fixing 6mm thick fiber hard board sheet lining
with but jointing and nails (Frame work and cover fillets to be
measured and paid for separately) Sqm 65 530.00
2 New (a) Providing and fixing vineered particle board 12mm thick
lining with but jointing and nails (Frame work and cover filets to
be measured and paid for separately) Sqm 115 625.00
(b) 20mm thick particle board. Sqm 115 675.00
3 New Providing and decorative type veneered particle board 12mm
thick lining with but jointing and nails (Frame work be paid Sqm 115 650.00
separately)
4 New Providing and fixing 12mm thick plywood lining with but
jointing and nails (Frame work and cover fillets to be measured
and paid for separately) Sqm 115 990.00
5 12.31 Providing and fixing 10mm thick plaster of Paris (Gypsum
anhydrous) ceiling tiles upto height of 5 meters above floor level
over fest class keil wood strips 25x6 mm with 10 mm gap in
between and reinforce with rabbets wir mis fix to woodes freme
(Frame work to be paid separetely)
Sqm 115 575.00
6 New Perforated ceiling tiles : Providing and fixing in position teak
wood perforated particle board ceiling tiles bonded with B.W.P.
type Phenol formaldehyde synthetic rains tile in size
60x60x12mm over kali wood timber frame of 50x30mm section
and suspended from the roof with the help of flat iron hangers of
size 20x44mm on under side leaving and expansion gap of 6mm
and with provision for providing necessary fighting fixtures
including three coats of flat oil paint of approved quality and
shade and a coat of pink primer/copal varnish of the side facing
the roof as per direction given by Engineer-In-Charge.
Sqm 1200.00
Same as above but with decorative ceiling tiles. Sqm 1350.00
7 New Wooden Partition: Providing and fixing in position 38mm thick
single skin partition with fibre of particle board frame of 900x
400mm section of 75x38m mind fixing (Panelled type) 19mm
thick teak wood particle board bounded with phenol
formaldehyde synthetic resin both face commercial confirming
to ISI specification no. 3097-1980 as per drawing complete with
painting/French polish/wax polish or as per direction given by
Engineer In Charge.
Sqm 1450.00
Same as in Item No. 7(a) above but with 19mm thick teak wood
particle board laminated on both faces. Sqm 2750.00
8 New Providing and fixing in position double skin wooden partition
with fiber or particle board frame of 900 x 1200mm rectangular
of section 50 x 38mm covered with 12mm thick teak wood
particle board commercial quality of both face duly painted two
coats of high gloss synthetic enamel paint over on priming
complete.
Sqm 2500.00
Same as in Item No. 8(a) above but covering with 12mm thick
teak wood particle board laminated on both faces. Sqm 2650.00
Page 41
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
9 New Wall Paneling : Providing and fixing in position wall panels of
plain teak wood particle board 12mm thick bonded with B.W.P.
type Phenol formaldehyde synthetic resin tiles kali wood frame
and provision for providing switch board fixtures etc. as per
drawing complete with polishing and fining with Fremg wax
polish as per direction given by Engineer-In-Charge.
Sqm 1550.00
Same as in Item No. 9(a) above but with one side laminated
instead of plain board. Sqm 2050.00
10 551 Supply and fixing of 2.5Cm. Thick deodar wood plains, ceiling
Including supply of beading 2.5Cm. X 4Cm. (1" x 1 ½") of deodar
wood over joints but excluding cost of ceiling joints if and when
necessary but Including cost of material, labour & T&P etc.
required for proper completion of the work.
Sqm 1600.00
552 Same as Item No. 551 above but of C.P. teak wood. Sqm 3075.00
553 As per Item No. 551 above but kail or cheer wood. Sqm 700.00
11 554 Supply and fixing A.C. Plain sheet ceiling includng beading
2.5cm x 4cm (1"x1½") of deodar wood, screws, bold and all
material, labour, T&P etc. complete, excluding cost of ceiling
joints if any required for proper completion of work.
Sqm 90 385.00
12 New Providing and fixing 12mm thick fiber hard board sheet lining
with but jointing and nails (Frame work and cover fillets to be
measured and paid for separately)
Sqm 75.00 600.00
13 21.2 Providing and fixing 12 mm thick prelaminated particle board 21.2.1
flat pressed threelayer or graded wood particle board conforming
to IS: 12823 Grade l Type ll, in panelling fixed in aluminum
doors, windows shutters and partition frames with C.P. brass /
stainless steel screws etc. complete as per architectural
drawings and directions of engineer-in-charge.Pre-laminated
particle board with decorative lamination on one side and
balancing lamination on other side
Sqm - 185.00
Page 42
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
15 12.45 Providing and fixing false ceiling at all height including providing and 12.45.1
fixing of frame work made of special sections, power pressed from M.S.
sheets and galvanized with zinc coating of 120 gms/sqm (both side
inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm
wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm
centre to centre, one flange fixed to the ceiling with dash fastener 12.5
mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to
the angle hangers of 25x10x0.50 mm of required length with nuts &
bolts of required size and other end of angle hanger fixed with
intermediate G.I. channels 45x15x0.9 mm running at the spacing of
1200 mm centre to centre, to which the ceiling section 0.5 mm thick
bottom wedge of 80 mm with tapered flanges of 26 mm each having lips
of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction
perpendicular to G.I. intermediate channel with connecting clips made
out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including
fixing perimeter channels 0.5 mm thick 27 mm high having flanges of
20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition
with the help of rawl plugs at 450 mm centre, with 25mm long dry wall
screws @ 230 mm interval, including fixing of gypsum board to ceiling
section and perimeter channel with the help of dry wall screws of size
3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush
finish of tapered and square edges of the board with recommended
jointing compound , jointing tapes , finishing with jointing compound
in 3 layers covering upto 150 mm on both sides of joint and two coats
of primer suitable for board, all as per manufacturer's specification and
also including the cost of making openings for light fittings, grills,
diffusers, cutouts made with frame of perimeter channels suitably
fixed, all complete as per drawings, specification and direction of the
Engineer in Charge but excluding the cost of painting with :12.5 mm
thick tapered edge gypsum plain board conforming to IS: 2095- (Part I)
: 2011 (Board with BIS Certification marks)
Page 43
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
17 12.52 Providing and fixing tiled false ceiling of specified materials of 12.52.1
size 595x595 mm in true horizontal level, suspended on inter
locking metal grid of hot dipped galvanized steel sections (
galvanized @ 120 grams/ sqm, both side inclusive) consisting of
main "T" runner with suitably spaced joints to get required
length and of size 24x38 mm made from 0.30 mm thick
(minimum) sheet, spaced at 1200 mm center to center and cross
"T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet,
1200 mm long spaced between main "T" at 600 mm center to
center to form a grid of 1200x600 mm and secondary cross "T"
of length 600 mm and size 24x25 mm made of 0.30 mm thick
(minimum) sheet to be interlocked at middle of the 1200x600
mm panel to form grids of 600x600 mm and wall angle of size
24x24x0.3 mm and laying false ceiling tiles of approved texture
in the grid including, required cutting/making, opening for
services like diffusers, grills, light fittings, fixtures, smoke
detectors etc. Main "T" runners to be suspended from ceiling
using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to
ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm
GI adjustable rods with galvanised butterfly level clips of size 85
x 30 x 0.8 mm spaced at 1200 mm center to center along main
T, bottom exposed width of 24 mm of all T- sections shall be pre-
painted with polyester paint, all complete for all heights as per
specifications, drawings and as directed by Engineer-in-charge.
GI Metal Ceiling Lay in plain Tegular edge Global white color
tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop;
made of G I sheet having galvanizing of 100 gms/sqm (both
sides inclusive) and electro statically polyester powder coated of
thickness 60 microns (minimum), including factory painted after
bending.
Sqm - 1130.00
18 9.158 Providing and fixing in wall lining medium density fibre board
IS: 14587:1998 marked, Pre-laminated one side decorative
lamination and other side balancing lamination, with
necessary fixing arrangement and screws etc. complete.
Page 44
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
20 9.105 Providing and fixing partition upto ceiling height consisting of G.I. 9.105.1
frame and required board, including providing and fixing of frame work
made of special section power pressed/ roll form G.I. sheet with zinc
coating of 120 gms/sqm(both side inclusive), consisting of floor and
ceiling channel 50mm wide having equal flanges of 32 mm and 0.50
mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre
to centre with dash fastener of 12.5 mm dia meter 50 mm length or
suitable anchor fastener or metal screws with nylon plugs and the
studs 48 mm wide having one flange of 34 mm and other flange 36 mm
and 0.50 mm thick fixed vertically within flanges of floor and ceiling
channel and placed at a spacing of 610 mm centre to centre by 6 mm
dia bolts and nuts, including fixing of studs along both ends of
partition fixed flush to wall with suitable anchor fastener or metal
screws with nylon plugs at spacing of 450 mm centre to centre, and
fixing of boards to both side of frame work by 25 mm long dry wall
screws on studs, floor and ceiling channels at the spacing of 300 mm
centre to centre. The boards are to be fixed to the frame work with
joints staggered to avoid through cracks, Galvanised M.S. fixing
channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm
each with zinc coating of 120 gms/sqm(both side inclusive)) to be
provided at the horizontal joints of two boards, fixed to the studs using
metal to metal flat head screws, including jointing and finishing to a
flush finish with recommended jointing compound, jointing tape, angle
beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two
coats of primer suitable for board as per manufacture's specification
and direction of engineer in charge all complete. 75 mm overall
thickness partition with 12.5 mm thick double skin fire rated Glass
Reinforced Gypsum (GRG), plaster board conforming to IS: 2095: (part
3) 1996 (Board with BIS Certification marks)
Page 45
CHAPTER- 13
PLASTER & POINTING
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
1 13.9 12mm Cement plaster with cement mortar in proportion of 13.9.1
1:3 cement & coarse sand of single coat for interior
plastering upto floor two level including internal rounded
angles chamfers, and rounded angles not exceeding 80mm
in girth and finished even and smooth.
Sqm 80.00 190.00
2 13.4 12mm Cement plaster with cement mortar in proportion of 13.4.1
1:4 cement & coarse sand of single coat for interior
plastering upto floor two level including internal rounded
angles chamfers, and rounded angles not exceeding 80mm
in girth and finished even and smooth.
Sqm 80.00 180.00
3 13.4 12mm Cement plaster with cement mortar in proportion of 13.4.2
1:6 cement & coarse sand of single coat for interior
plastering upto floor two level including internal rounded
angles chamfers, and rounded angles not exceeding 80mm
in girth and finished even and smooth.
Sqm 80.00 160.00
4 13.1 12mm Cement plaster with cement mortar in proportion of 13.1.1
1:4 cement & fine sand ( Dholpur sand) (Not less than in
1.25 FM) of single coat for interior plastering upto floor two
level including internal rounded angles chamfers, and
rounded angles not exceeding 80mm in girth and finished
even and smooth.
Sqm 80.00 165.00
5 13.1 12mm Cement plaster with cement mortar in proportion of 13.1.2
1:6 cement & fine sand ( Dholpur sand) (Not less than in
1.25 FM) of single coat for interior plastering upto floor two
level including internal rounded angles chamfers, and
rounded angles not exceeding 80mm in girth and finished
even and smooth.
Sqm 80.00 155.00
6 13.5 15mm Cement plaster with cement mortar in proportion of 13.5
1:3 cement & coarse sand of single coat for interior
plastering upto floor two level including internal rounded
angles chamfers, and rounded angles not exceeding 80mm
in girth and finished even and smooth.
Sqm 90.00 210.00
7 13.5 15mm Cement plaster with cement mortar in proportion of 13.5.1
1:4 cement & coarse sand of single coat for interior
plastering upto floor two level including internal rounded
angles chamfers, and rounded angles not exceeding 80mm.
In girth and finished even and smooth.
Sqm 90.00 190.00
8 13.5 15mm Cement plaster with cement mortar in proportion of 13.5.2
1:6 cement & coarse sand of single coat for interior
plastering upto floor two level including internal rounded
angles chamfers, and rounded angles not exceeding 80mm
in girth and finished even and smooth.
Sqm 90.00 180.00
Page 46
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
9 13.2 15mm Cement plaster with cement mortar in proportion of 13.2.1
1:4 cement & fine sand ( Dholpur sand) (Not less than in
1.25 FM) of single coat for interior plastering upto floor two
level including internal rounded angles chamfers, and
rounded angles not exceeding 80mm in girth and finished
even and smooth.
Sqm 90.00 170.00
10 13.2 15mm Cement plaster with cement mortar in proportion of 13.2.2
1:6 cement & fine sand ( Dholpur sand) (Not less than in
1.25 FM) of single coat for interior plastering upto floor two
level including internal rounded angles chamfers, and
rounded angles not exceeding 80mm in girth and finished
even and smooth.
Sqm 90.00 175.00
11 13.9 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) 13.9.2
finished with 3mm thick floating coat of neat cement. Sqm 100.00 310.00
12 13.6 20mm Cement plaster with cement mortar in proportion of 13.6.1
1:4 cement & coarse sand of single coat for interior
plastering upto floor two level including internal rounded
angles chamfers, and rounded angles not exceeding 80mm
in girth and finished even and smooth.
Sqm 100.00 260.00
13 13.16 6mm Celling plaster 1:3 (1 cement : 3 fine sand) cement & 13.16
fine sand in F.M. not less than 1.25, 1:3 including chiping of
RCC surface before ceiling plaster. The cost of including all
material, labour T&P and scafolding etc. complete.
(a) With cement mortar 1:4 (1 cement : 4 fine sand) (not less 14.1.1
than in 1.25 FM) Sqm 130.00 210.00
(b) With cement mortar 1:4 (1cement: 4 coarse sand) 14.1.2 Sqm 130.00 220.00
Page 47
PWD/
PWD/ Over All
Sl. CPWD LABOUR
DSR SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
19 New Washed stone grit plaster on exterior walls height upto 10
metre above ground level, in two layers, under layer 12 mm
cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the
under layer with scratching tool, applying cement slurry on
the under layer @ 2 Kg of cement per square metre, top
layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse
sand : 2 stone chipping 10 mm nominal size), in panels with
groove all around as per approved pattern, including
scrubbing and washing the top layer with brushes and
water to expose the stone chippings ,complete as per
specification and direction of Engineer-in- charge (payment
for providing grooves shall be made separately).
Page 48
CHAPTER- 14
FLOORING
Page 49
PWD/ PWD/ Over All
Sl. LABOUR
DSR SI Description of the Work CPWD Unit Rate
No. RATE
No Spec. No. (Rs)
6 612 Brick on an edge floor with class-150 brick laid in
cement mortar consisting of one part of cement and 6
part fine sand of fineness modules 1.25 and pointed
with cement mortar 1:2 over 8cm thick base concrete
(pointing and base concrete to be paid separately)
including supply of all material, labour and tools and
plants etc. required for completion of the work.
Sqm 3200.00
12 11.23A Providing and fixing 18 mm thick Granite (gang saw 11.23.4
cut) mirror polished, premoulded and prepolished,
machine cut for kitchen platforms, vanity counters,
window sills, facias and similar locations, of required
size, approved shade, colour and texture laid over 20
mm thick base cement mortar 1:4 (1 cement : 4 coarse
sand), joints treated with white cement, mixed with
matching pigment, epoxy touch ups, including
rubbing, curing, moulding and polishing to edges to
give high gloss finish etc. complete at all levels. (Slab
area above 0.50 Sq.M.)
Sqm 3550.00
Page 50
PWD/ PWD/ Over All
Sl. LABOUR
DSR SI Description of the Work CPWD Unit Rate
No. RATE
No Spec. No. (Rs)
13 _ Providing edge maulding to 18mm thick Granite stone,
including machine polishing to edge to give hige gloss
finish etc. complete as per design approved by
Engineer-in-Charge.
RM 245.00
14 11.37 Providing and laying Ceramic glazed floor tiles of size 11.37
300x300 mm (thickness to be specified by the
manufacturer) of 1st quality conforming to IS : 15622
of approved make in colours such as White, Ivory,
Grey, Fume Red Brown, laid on 20 mm thick cement
mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with
grey cement slurry @ 3.3 kg/sqm including pointing
the joints with white cement and matching pigment
etc., complete.
Page 51
PWD/ PWD/ Over All
Sl. LABOUR
DSR SI Description of the Work CPWD Unit Rate
No. RATE
No Spec. No. (Rs)
20 11.27A Providing and laying Vitrified tiles in floor with lean 11.41.1
concrete of 500x 500mm sizes (thickness 10mm), with
a water absorption less than 0.08% and conforming to
IS:15622, of approved brand & manufacturer, in
desired colours and shades, laid with cement based
high polymer modified quick set tile adhesive (water
based) conforming to IS : 15477, including grouting of
joints. including preparation of 75mm thick base with
concrete 1:4:8 Cement, Coarse sand and 40 mm B/B
complete as per Engineer -In -Charge.
Sqm 450.00 1700.00
21 Same as above but for 600X600mm size. 11.41.2 Sqm 450.00 1800.00
22 11.41A Providing and laying Vitrified tiles in floor without 11.41.1 A
lean concrete of 500x 500mm sizes (thickness 10mm),
with water absorption less than 0.08% and conforming
to IS:15622, of approved brand & manufacturer, in
desired colours and shades, laid with cement based
high polymer modified quick set tile adhesive (water
based) conforming to IS : 15477, including grouting of
joints.
Sqm 380.00 1400.00
23 (A) Same as above but for 600X600mm size. 11.41.2 A Sqm 380.00 1500.00
24 631 Providing and fixing glass strips of 4mm thick in joints
of floor and skirting at the time fo laying Including
labour, T&P etc. complete in all respect.
Page 52
CHAPTER- 15
PAINTING & DISTEMPERING
Over
PWD/ PWD/
Sl. LABOUR All
DSR Description of the Work CPWD Unit
No. RATE Rate
SI No Spec. No.
(Rs)
1 New Applying priming coat over new steel and other metal
641 surface upto 10cm. In width or girth or small not
exceeding 0.10 Sq.M. area after and including preparing
the surface by thoroughly clearing oil, grease, dirt and
other foreign matter and scoured with wire brushed, fine
steel/wood. Scrapper, sand papering and knotting
including cost of all materials, labour T&P etc. required for
proper completion of work.
Sqm 14.00 32.00
19.61 (a) Same as in item 1 above but on new wood surfaces. Sqm 14.00 35.00
2 19.29 Painting 1st coat over priming coat (but excluding cost of
priming coat) on steel and other metal surfaces upto 10cm
width or girth or small articles not exceeding 0.10 Sq.M. in
area with superior synthetic enamel such as Luxol 3, Hi
gloss Apcolite, Superlac, Dulux specified brushing to give
and even shade and including the cleaning the surface of
all dirt, dust and other foreign matter sand papering and
scrapping including cost of all materials, labour, tools and
plants etc. required for proper completion of work.
Page 53
Over
PWD/ PWD/
Sl. LABOUR All
DSR Description of the Work CPWD Unit
No. RATE Rate
SI No Spec. No.
(Rs)
14 650 As in item No. 649 above but for every coat after first coat
of subsequent coat. Sqm 13.00 24.00
15 652 First coat hot bitumen on new wood and wood based 15.5.1
surfaces using 0.16 kg of bitumen per Sq.M. to give an
even shade including cleaning of all dirt, dust and other
foreign matter including cost of all material.
Sqm 9.00 17.00
16 653 As in item no. 652 above but for every coat after first coat 15.5.2
using 0.12kg of coaltar per Sq.M. Sqm 8.00 13.00
17 654 Applying first coat of any approved preservative on new
wood work and wood based surfaces including preparing
the surface by thoroughly cleaning oil, grease, dirt and
foreign matter sand preparing and knotting including cost
of all materials.
Sqm 12.00 30.00
18 655 As in Item no. 654 above but for every coat after first coat
or on previously treated surface. Sqm 12.00 25.00
19 656 Oiling wood work with double boiled linseed oil to give an
even surface including cleaning the surface of all dirt dust
and sand papered so as to produce a smooth dry and matt
surface including cost of all materials.
Sqm 7.00 13.00
20 657 Removing oil paint or varnish from steel and other metal
surface of from wood based surface with paint remover of
approved brand and manufacturer or with caustic soda
and making the surface even including cost of all
materials.
Sqm 9.00 16.00
21 658 Polishing with French polish (in proportion 2 bees wax :
1.5 linseed oil : 1 turpentine oil : 0.5 varnish by weight) on
new wood based surface including cleaning the surface of
all dirt dust and same papered smooth and a coat of wood
filler including cost of all material
Sqm 20.00 62.00
22 659 As in item no. 658 above but polishing on previously
polished wood and wood based surface (wax polish in
proportion 2 turpentine oil : 0.5 varnish by weight) Sqm 10.00 32.00
23 660 Finishing walls with water proofing cement paint of
approved make such as Super snowcem, Durocem,
Robiance, Guttucem, Supercem quality and of required
shade on under coated wall surface (One coat) over and
including one coat white cement primer to give and even
shade after thoroughly after brushing the surface .
Sqm 15.00 58.00
24 661 Same as item no. 660 above but for each coat of
waterproof cement paint after the first coat to give an even
shade. Sqm 7.00 27.00
25 New Finishing walls with sandlex matt. Coat over a priming
coat of water proof cement paint of approved quality such
as super "Snowcem Durocem" super quality of required
shade on undecorated wall surface to give an even shade
after thoroughly brushing the surface to remove all dirt
and remains of loose powdered material including curing
the cost of all material, labour, T&P etc. complete.
Page 54
Over
PWD/ PWD/
Sl. LABOUR All
DSR Description of the Work CPWD Unit
No. RATE Rate
SI No Spec. No.
(Rs)
26 662 Finishing walls with one coat of waterproof cement
paint of approved quality on previously old treated surface
with this paint to give an even shade after thoroughly
brushing the surface to remove all dirt and remains of
loose powder material including curing and cost of all
materials.
Sqm 12.00 37.00
27 18.58 Wall painting (one coat) with plastic emulsion paint of
approved brand and manufacture on decorative wall
surface to give an even shade including thoroughly
brushing the surface clean all of dirt, grease loose pieces
and prepare smooth.
Sqm 20.00 100.00
28 New Extra over item no. 18.58 above and for every subsequent
coat of wall painting with plastic emulsion paint of
approved brand and manufacturer. Sqm 13.00 68.00
29 13.68 Sprit polish including sand paperings cleaning the
surface properly and then applying the sprit polish colour
with shining finishing supply of all labour material and
T&P required for proper completion of work.
Page 55
Over
PWD/ PWD/
Sl. LABOUR All
DSR Description of the Work CPWD Unit
No. RATE Rate
SI No Spec. No.
(Rs)
34 13.60.1 Finishing walls with acrylic emulsion paint of
approved brand and manufacture and of required shade
on undacorated wall surface to give even shade over
including curing and cost of all material, labour, T&P etc.
required for proper completion of work.for two coat.
NOTE :- If ISI mark approved brand paint is not used then the rate be deducted by
minimum 10%. The consumption of material will be taken as per manufacturer
recommendation. It should not be calculated from UP P.W.D. skeleton of analysis of rate.
Page 56
CHAPTER- 16
WHITE WASHING & COLOUR WASHING
PWD Over All
Sl. PWD LABOUR
Description of the Work Spec. Unit Rate
No. No RATE
No. (Rs)
1 671 White washing with lime on under coated wall surfaces 13.38
(Two coat) to give an even shade including thoroughly
brooming the surface to remove all dirt, dust mortar
drop and loose scales of lime wash and other foreign
matter.
Sqm 6.00 9.00
2 672 White washing with lime on undecorated wall surface 13.37
(one coat) to give an even shade including thoroughly
brooming the surface to remove all dirt, dust mortar
drop and loose scales of lime wash and other foreign
matter.
Sqm 5.00 8.00
3 673 Extra over SI No. 672 above for every subsequent coat
of white washing Sqm 3.00 4.50
4 New Colour washing with Portland cement slurry on
674 undercoated wall surface (one coat) to give a smooth
surface to remove all dirt, mortar drop an other foreign
matter.
Sqm 5.00 10.00
5 675 Colour washing with lime on under coated wall surfaces 13.39
(two coat) over & including a primary coat of white
washing to give an even shade after thoroughly
brooming the surface to remove all dirt, dust mortar
drop and other foreign matter.
Sqm 9.00 17.00
6 675 A Extra over SI No. 675 for every subsequent coat of
colour wash on decorated surface. Sqm 3.50 7.50
7 Distempering with dry distemper of approved brand (two
coats) and of required shade on undecorated wall
surface to give an even shade over and including
priming coat of whiting after thoroughly brushing the
surface free from dropping & other foreign matter
including preparing the surface even and sand papered
smooth.
Sqm 18.00 47.00
8 Extra over item No. 8 for every subsequent coat of
distempering with dry distemper of approved and
manufacturer. Sqm 5.00 25.00
9 682 One Coat Priming & One Coat Distempering with dry
distemper of approved brand and required shade on
undecorated wall surface to give an even surface
including supply of all materials, labour and T&P etc.
complete
Sqm 19.00 46.00
10 Extra over item 11 for every subsequent coat of
distempering with dry distemper of approved and
manufacturer. Sqm 5.00 27.00
NOTE:- The rates include cost of all materials such as Plaster of Paris, whiting, glue, brushes, sand
paper and other sandries etc., but exclusive as cost of specified material as mentioned in
respective items in labour rates.
Page 57
CHAPTER- 17
DEMOLITION & DISMANTLING
PWD C.P.W.D/P Over All
Sl. LABOUR
SI Description of the Work .W.D. Unit Rate
No. RATE
No. Spec. No. (Rs)
1 691 Dismantling sundries brick work including stacking of 17.3
dismantled materials as directed by Engineer-In-Charge
within a distance of 60 meters (200 feet). Cum - 90.00
2 692 Dismantling brick work or stone work in lime or cement
mortar and including stacking of materials as directed by
Engineer-In-Charge within a distance of 60 meters (200
feet).
Cum - 450.00
3 693 As in item (692) above but in mud mortar. 17.2.1 Cum - 240.00
4 694 Dismantling reinforced cement concrete or reinforced 17.3
brick work including stacking of dismantled materials as
directed by Engineer-In-Charge within a distance of 60
meters (200 feet).
Cum - 950.00
5 695 Dismantling jack arched or wooden beam and bajra roofs 17.5.1
including beam and roof concrete and including stacking
of dismantled materials as directed by Engineer-In-
Charge within a distance of 60 meters (200 feet).
Sqm - 125.00
6 696 As in item (695) above but only roof concrete. 17.4.2 Sqm - 350.00
7 697 Dismantling cement concrete or brick or granolithic floors 17.5.1
including stacking of dismantled materials as directed by
Engineer-In-Charge within a distance of 60 meters (200
feet).
Sqm - 55.00
8 698 As in item (697) above but floor to be stone flagged or tiled 17.5.2 Sqm - 70.00
9 floor.
699 Dismantling single tiled roof, any kind including purlin
and batterns and including stacking of dismantled
materials as directed by Engineer-In-Charge within a
distance of 60 meters (20 feet).
Sqm - 75.00
10 700 As in item (699) above but double tiled roof. Sqm - 115.00
11 701 Dismantling corrugated iron floors wall or partition 17.7
including purlin battens and vertical support and
including stacking of materials as directed by Engineer-In-
Charge within a distance of 60 meters (200 feet)
Sqm - 45.00
12 702 Dismantling of girders, trusses and other steel work 17.8
including stacking of dismantled materials as directed by
Engineer-In-Charge within a distance of 60 meters (200
feet).
Qtl. - 1275.00
13 703 Dismantling doors and windows including stacking of 17.9.3
materials as directed by Engineer-In-Charge with a
distance of 60 meters (200 feet). Sqm - 65.00
14 704 Dismantling doors and windows leaves including stacking 19.9.1
of materials as directed by Engineer-In-charge within a
distance of 60 meters (200 feet). Sqm - 30.00
15 705 Dismantling doors and windows leaves including 17.9.2
chaukhats but excluding hold fasts and including
stacking of materials as directed by Engineer-In-Charge
within a distance of 60 meters (200 feet)
Sqm - 65.00
Page 58
PWD C.P.W.D/P Over All
Sl. LABOUR
SI Description of the Work .W.D. Unit Rate
No. RATE
No. Spec. No. (Rs)
16 706 Dismantling existing plaster including disposal of refuse 17.10
as directed by Engineer-In-Charge within a distance of 60 Sqm - 35.00
17 707 Racking out joints of brick work in cement or lime mortar 17.11
to depth of 1cm (3/8") including disposal of refuse as
directed by the distance of 60 meters (200 feet)
Sqm - 25.00
18 708 Scrapping old white or colour wash including disposal of 17.12
refuse as directed by Engineer-In-charge within a
distance of 60 meters (200 feet) Sqm - 12.00
19 New Dismentalling of B.O.E soling/Inter locking tiles Including -
Stacking of servicable material and disposal of
unservicable material within a lead of 50m as per
direction of EI/C (Labour only)
Sqm - 10.00
Page 59
CHAPTER- 18
MARBLE WORK IN WALL LINING etc.
PWD/ Over All
Sl. PWD/CPWD LABOUR
DSR Description of the Work Unit Rate
No. Spec. No. RATE
SI No (Rs)
1 Dholpur Stone work for wall lining etc. (Veneer -
work) 40mm thick in cement mortar 1:3 (1 cement
: 3 coarse sand) including camping jointing in
white cement mortar 1:2 (1 white cement : 2 stone
dust) with an admixture of pigment matching the
stone shade.
Sqm 525.000 1150.000
2 Finishing walls with sandlex matt. Coat over a -
priming coat of water proof cement paint of
approved quality such as super "Snowcem
Durocem" super quality of required shade on
undercoated wall surface to give an even shade
after thoroughly brushing the surface to remove
all dirt and remains of loose powdered material
including curing the cost of all material, labour,
T&P etc. complete.
Sqm 28.000 100.000
3 7.23 Red sand stone work for wall lining etc. (Veneer -
work) 30mm thick in cement mortar 1:3 (1 cement
: 3 coarse sand) including camping jointing in
white cement mortar 1:2 (1 white cement : 2 stone
dust) with an admixture of pigment matching the
stone shade.
Sqm - 1600.000
4 7.3 30 mm red sand stone sun-shade (chisel-dressed) -
supported on red sand stone brackets, fixed in
walls with cement mortar 1:4 (1 cement : 4 coarse
sand),
including finishing complete.
Sqm 500.000 800.000
5 7.33 Providing and fixing Red Sand stone jali 40 mm -
thick throughout in cement mortar 1:3 (1 cement :
3 coarse sand), including pointing in white cement
mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment, matching the stone shade,
jali slab without any chamfers etc.
Sqm 800.000 6100.000
6 7.6 Coursed rubble masonry (first sort) with hard -
stone in foundation and plinth with Cement
mortar 1:4 (1 cement : 4 coarse sand) Cum 1250.000 5000.000
7 7.6 Coursed rubble masonry (first sort) with hard -
stone in foundation and plinth with Cement
mortar 1:3 (1 cement : 3 coarse sand) Cum 1250.000 5100.000
8 7.8 Coursed rubble masonry (first sort) with hard -
stone in superstructure with Cement mortar 1:4 (1
cement : 4 coarse sand) Cum 1300.000 5300.000
9 7.8 Coursed rubble masonry (first sort) with hard -
stone in superstructure with Cement mortar 1:3 (1
cement : 3 coarse sand) Cum 1300.000 5500.000
Page 60
CHAPTER- 19
MISCELLANEOUS
Each - 240.00
6 Supply and fixing hexagonal/ Round G.P Fan Box of -
approved make made up of 1.0 mm thick I.S.I marked G.P
Sheet spot welded four to eight holes of 25.4 mm for pipe
entry of the Box. Holes Should be semi- Shuttered type
widh 0.5 mm G.P Sheet made uper and lower cover duly
Screwed Fitted widh 300 mm round zink coated M.S bar x
12 mm & brand name should be embossed . Fixing with
wiring conduit laid in the R.C.C Roof be four concreting
along wuth supply of all matereal, labour, T&P etc.
required for proper completion of the work. As per SI No.
1149
Each 30.00 150.00
Page 61
SCH PWD Over All
Sl. LABOUR
PWD Description of the Work Spec. Unit Rate
No. RATE
No No. (Rs)
7 Supply and laying of 25 mm dia heavey duty 2 mm thick -
P.V.C conduit complete with bends and other acessores as
required in slab along with reinforcement, before
concreting etc complete in all respect. As per SI No. 282A
RM 16.00 50.00
8 Breking of B/B 40 mm Gauge (20 to 40mm) - Cum 120.00 -
9 Breking of B/B 25 mm Gauge (20 to 25mm) - Cum 150.00 -
10 Filling empty cement bag sewing and palcing in position -
upto 60 mitre lead No. 6.00
11 Surface dewatering of foundation including all -
arrangement in KWH by diesel pump set. KWH - 40.00
Page 62
CHAPTER- 20
ROAD WORK
Page 63
SCH ITEM PWD Over All
Sl. LABOUR
PWD No Description of the Work Spec. Unit Rate
No. RATE
No NBO No. (Rs)
9 772(a) Scrapping old painted surface including disposal of all - As per Morth
scrapped material to distance of 30 mts (100 ft) as directed Standard Data Book
by Engineer-In-Charge. Cum Analysis
10 780 Patch repair of painted Kms with tar or Bitumen (labour -
only) including heating the paint to the required
temperature pouring it on the surface spreading of
necessary quantity of grit and ramming hard the same with
hand rammer/roller & also including cleaning with brushes
etc the existing surface after scrapping it to the water bound
surface in rectangular shape and spreading the dismantled
material on the patries as directed by Engineer-In-charge. As per Morth
Standard Data Book
Cum Analysis
11 Cleaning Of existing painted surface and laying SDBC/ -
Premix over tack coat with graded approved grit and
bitumen Including heating the paint to the required
temperature and mixing including cartage of material
maintenance of side partries and watering them during
operation for proper complation of work. take a length of 1/2
furlong 330×12=3960sft. or 368sqm (For Deparmental As per Morth
Plant Labour Rate Only). Standard Data Book
Sqm Analysis
12 Cleaning of Premix Surface and laying Seal Coat with -
approved grit and bitumen Including heating of paint to the
required tempareture maintenance of patries and watering
them during operation for proper completion of work. Take a
length of 1/2 area covered 330×12=3960sft. As per Morth
(For Deparmental Plant Labour Rate Only) Standard Data Book
Sqm Analysis
13 New Laying and fixing of N.P.-3 Hume pipe in proper position as
directed by E/I including cartage of pipes/collars upto 30m
distance (labour only) excluding cost of pipes/collars.
Cum 100.00 -
17 790(c) Laying of Stone boulders over slopes in pitching including its
cartage to site of work from stacking site and also including
a lead upto 100m and lift upto 3m loading and unloading -
etc. (Labour only)
Cum 250.00 -
Page 64
SCH ITEM PWD Over All
Sl. LABOUR
PWD No Description of the Work Spec. Unit Rate
No. RATE
No NBO No. (Rs)
18 790(d) As in Item 790(b) but in apron at the toe of slope in river bed
(Labour only) -
Cum 300.00 -
19 790(e) Laying 40mm gauge stone/brick ballast for fiter over slopes
including dressing, leveling and ramming etc. and a lead -
upto 100m and lift upto 3m (labour Only) Cum 200.00 -
20 790(f) Providing and laying of 40 mm gauge B/B under Hume
pipe culvert foundation & road work including all materials,
labour and T&P etc. required for completion of work. -
cum - 7000.00
Page 65
SCH ITEM PWD Over All
Sl. LABOUR
PWD No Description of the Work Spec. Unit Rate
No. RATE
No NBO No. (Rs)
Sqm 515.00
25 New Providing and laying of hot applied thermoplastic compound -
Item 5mm thick including reflectrorising glass beeds @ 500gms
per sqm. Area, thiclness of 5mm is exclusive of surface
applied glass beeds as per IRC:35. The finish surface to be
level, uniform and free from streaks and holes. composition
of thermoplastic meterial shall be as per table 800-3 of -
clause 803 of MORTH including cost of all meterial, labour,
T&P etc. require for proper completion of work as direction
by engineer-in-charge.
Sqm 1000.00
26 Providing, laying and rolling of open-graded premix carpet of -
20 mm thickness composed of 13.2 mm to 5.6 mm
aggregates and using (VG-30) bitumen to required line,
grade and level to serve as wearing course on a previously
prepared base, including mixing in a Mixoll, laying and
rolling with a three wheel 80-100 kN static roller capacity,
finished to required level and grades to be followed by seal As per Morth
coat as per Technical specification clauses 508. Standard Data Book
Analysis
Page 66
CHAPTER- 21
WATER SUPPLY MATERIAL
Note : The items should be of I.S.I. Marked conforming to respective IS codes and supplied at site.
Over All
Sl.
MATERIAL WITH CLASS SIZE UNIT Rate
No.
(Rs)
1 G.I. Pipe Class-B 15mm dia RM 90.00
2 G.I. Pipe Class-B 20mm dia RM 115.00
3 G.I. Pipe Class-B 25mm dia RM 170.00
4 G.I. Pipe Class-B 32mm dia RM 205.00
5 G.I. Pipe Class-B 40m dia RM 240.00
6 G.I. Pipe Class-B 50mm dia RM 290.00
7 G.I. Tee 15mm dia Dozen 280.00
8 G.I. Tee 20mm dia Dozen 440.00
9 G.I. Tee 25mm dia Dozen 620.00
10 G.I. Tee 40mm dia Dozen 900.00
11 G.I. Jamnut 15mm dia Dozen 85.00
12 G.I. Jamnut 20mm dia Dozen 90.00
13 G.I. Jamnut 25mm dia Dozen 145.00
14 G.I. Jamnut 40mm dia Dozen 190.00
15 G.I. Jamnut 50mm dia Dozen 270.00
16 G.I. Elbow 15mm dia Dozen 170.00
17 G.I. Elbow 20mm dia Dozen 280.00
18 G.I. Elbow 25mm dia Dozen 450.00
19 G.I. Elbow 40mm dia Dozen 1000.00
20 G.I. Elbow 50mm dia Dozen 1500.00
21 G.I. Socket 15mm dia Dozen 170.00
22 G.I. Socket 20mm dia Dozen 250.00
23 G.I. Socket 25mm dia Dozen 340.00
24 G.I. Socket 40mm dia Dozen 650.00
25 G.I. Socket 50mm dia Dozen 1000.00
26 G.I. Reducing Socket 25mm to
15mm dia Dozen
300.00
27 G.I. Reducing Socket 25mm to
20mm dia Dozen
300.00
28 G.I. Reducing Socket 40mm to
25mm dia Dozen
700.00
29 G.I. Cross Tee 15mm dia Dozen 400.00
30 G.I. Cross Tee 20mm dia Dozen 550.00
G.I. Cross Tee 25 mm dia Dozen 580.00
28 G.I. Reducing Socket 40mm to
25mm dia Dozen
700.00
29 G.I. Cross Tee 15mm dia Dozen 400.00
30 G.I. Cross Tee 20mm dia Dozen 550.00
31 G.I. Cross Tee 25mm dia Dozen 925.00
32 G.I. Reducing Tee 25x25x15mm
dia Dozen
700.00
33 G.I. Reducing Tee 20x20x15mm
dia Dozen
425.00
34 G.I. Reducing Tee 30x30x15mm
dia Dozen
980.00
Page 67
Over All
Sl.
MATERIAL WITH CLASS SIZE UNIT Rate
No.
(Rs)
35 G.I. Reducing Tee Class B 40x40x15mm
dia Dozen
1375.00
36 PVC ball float valve with brass and union complete. 15mm dia
Each
180.00
37 PVC ball float valve with brass and union complete. 20mm dia
Each
210.00
38 PVC ball float valve with brass and union complete. 25mm dia
Each
280.00
39 PVC ball float valve with brass and union complete. 30mm dia
Each
360.00
40 PVC ball float valve 150mm dia Each 110.00
41 PVC ball float valve 200mm dia Each 115.00
42 PVC ball float valve 250mm dia Each 125.00
43 Brass bib cock heavy quality 15mm dia 400
gms Each
210.00
43(a) Brass bib cock heavy quality 15mm dia 200
gms. Each
125.00
44 Brass bib cock heavy quality 15mm dia 200
gms. Each
500.00
45 Brass Stop Cock 15mm dia 200
gms. Each
130.00
46 Brass Stop Cock 15mm dia 400
gms. Each
200.00
47 Brass Stop Cock 20mm dia 400
gms Each
285.00
48 Brass bib cock heavy quality 15mm dia 200
gms. Each
475.00
49 Brass Ferrule 15mm. Dia Each 120.00
50 Brass Ferrule 20mm dia Each 160.00
51 Brass Ferrule 25mm dia Each 180.00
52 Fullway Gate Valve 15mm dia Each 360.00
53 Fullway Gate Valve 20mm dia Each 460.00
54 Fullway Gate Valve 25mm dia Each 650.00
55 C.P. brass shower heavy quality 100mm dia Each 410.00
56 B.G.I. Union 15mm dia. Each 55.00
57 B.G.I. Union 20mm dia Each 90.00
58 B.G.I. Union 25mm dia Each 110.00
59 B.G.I. Union 32mm dia Each 135.00
60 B.G.I. Union 40mm dia Each 160.00
61 B.G.I. Union 50mm dia Each 215.00
62 G.I. Long Screw 15 mm dia Each 60.00
63 G.I. Long Screw 20 mm dia Each 75.00
64 G.I. Long Screw 25 mm dia Each 95.00
65 G.I. Long Screw 32 mm dia Each 110.00
66 G.I. Long Screw 40 mm dia Each 120.00
67 G.I. Long Screw 50 mm dia Each 150.00
68 (a) G.I. Nipple 50mm Long 15 mm dia Each 11.00
(b) G.I. Nipple 50mm Long 20 mm dia Each 13.00
69 (a) G.I. Nipple 75mm Long 15 mm dia Each 16.00
(b) G.I. Nipple 75mm Long 20 mm dia Each 16.00
Page 68
Over All
Sl.
MATERIAL WITH CLASS SIZE UNIT Rate
No.
(Rs)
70 (a) G.I. Nipple 100mm Long 15 mm dia Each 25.00
(b) G.I. Nipple 100mm Long 20 mm dia Each 35.00
71 Brass Ball cock complete with Ball and Brass rod 15 mm dia
Each
235.00
72 Brass Ball cock complete with Ball and Brass rod 20 mm dia Each 265.00
73 Brass Ball cock complete with Ball and Brass rod 25 mm dia Each 375.00
74 (a) C.I. Bib cock with Brass rod heavy quality 200gms. 15 mm dia
Each
85.00
(b) C.I. Bib cock with Brass rod heavy quality 20 mm dia
200gms. Each
95.00
75 (a) C.I. Bib cock with Brass rod heavy quality 25 mm dia Each 105.00
76 C.I. Nozzle C.I. Stop cock heavy quality 200 gm. 15 mm dia Each 50.00
77 (a) C.I. Jali 100 x 100 mm
Each
35.00
(b) C.I. Jali 125 x 125 mm
Each
40.00
(c) C.I. Jali 150 x 150 mm
Each
45.00
78 (a) C.I. Jali Round 100mm dia Each 45.00
(b) C.I. Jali Round 125mm dia Each 50.00
(c) C.I. Jali Round 150mm dia Each 55.00
79 C.P. stop cock with Brass rod 400 gm Each 430.00
80 C.P. Pillar cock with Brass spindle. 15mm dia Each 400.00
81 (a) C.P. Brass waste jali for Sink Each 160.00
(b) C.P. Brass waste jali for Wash Basin Each 80.00
82 P.V.C. waste pipe for W.H.B./Sink Each 45.00
83 P.V.C. connection 450mm long with two brass units 15mm dia
Each
65.00
84 P.V.C. Pipe 600mm dia long with two brass units 15mm dia Each 85.00
Page 69
CHAPTER- 22
SANITARY MATERIAL
Page 70
Over All
Sl.
MATERIAL WITH CLASS UNIT Rate
No.
(Rs)
37 As in Item above 50mm dia Each 625.00
38 As in Item above 75mm dia Each 820.00
39 M.S. Holder bat clamp for HCI pips 100mm dia. Each 75.00
40 As in Item above but 50mm dia Each 55.00
41 As in Item above but 75mm dia Each 65.00
42 HCI heel rost bend 75mm dia. Each 210.00
43 As in Item above but 100mm dia Each 295.00
44 As in Item above but 50mm dia Each 155.00
45 HCI cross with access door nuts and washer complete 100x100x100mm Each 550.00
46 HEP make HCI bend with door complete 100mm dia. Each 300.00
47 HEP make HCI bend with door complete 75mm dia. Each 275.00
48 HEP make HCI terminal guard 150mm dia. Each 170.00
49 HEP make HCI terminal guard 100mm dia. Each 155.00
50 HEP make HCI terminal guard 75mm dia. Each 145.00
51 HEP make HCI terminal guard 50mm dia. Each 135.00
52 HEP make HCI collar socket 150mm dia. Each 310.00
53 HEP make HCI collar socket 100mm dia. Each 155.00
54 HEP make HCI collar socket 75mm dia. Each 135.00
55 HEP make HCI terminal collar socket 50mm dia Each 110.00
56 Pig lead Each 150.00
57 HEP/Equi. Make HCI plain bend 100mm dia Each 275.00
58 HEP/Equi. Make HCI plain bend 75mm dia Each 230.00
59 HEP/Equi. Make HCI plain bend 50mm dia Each 175.00
60 HEP/Equi. Make HCI plain bend door complete 50mm dia Each 450.00
61 S.W. pipe in 600mm length prefect made 100mm dia. Each 70.00
62 As in Item above 150mm dia. Each 105.00
63 S.W. gully trap 150x100 mm dia. Each 300.00
64 S.W. gully trap 130x100mm size Each 135.00
65 HCI grating 100mm dia Each 40.00
66 C.I. Cover 300x300mm. With frame complete. Kg 65.00
67 HEP Nahani trap of Indian make HCI 100x75mm Each 320.00
68 C.I. Cover with frame 400mm. Internal dia Kg 65.00
(a) C.I. Cover with frame 400mm Internal dia with weight not less 11 kgs. Kg 65.00
69 A.C. cowel 50mm dia. Each 75.00
70 A.C. cowel 100mm dia. Each 120.00
A.C. cowel 75mm dia. Each 90.00
71 S/O C.I. Pipe 1800mm long I.S.I. Mark I.S. 1729
(a) Kolkata Make Bic/Hepco 2" dia Each 610.00
(b) Kolkata Make Bic/Hepco 3" dia Each 800.00
(c) Kolkata Make Bic/Hepco 4" dia Each 1000.00
(d) Kolkata Make Bic/Hepco 6" dia Each 1750.00
(e) Neco Make C.I. Pipe 2" Dia Each 710.00
(f) Neco Make C.I. Pipe 3" Dia Each 925.00
(g) Neco Make C.I. Pipe 4" Dia Each 1000.00
(h) Neco Make C.I. Pipe 6" Dia Each 2000.00
72 MS clamp made with 32x5mm flat iron with out nut and bold complete for CI pipe Kg 65.00
Page 71
CHAPTER- 23
WATER SUPPLY
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
1 23.1 Fixing of the following sizes of G.I. Pipe-B, class
Jindal/J.C.T. m with G.I. Fittings I.S.I. Marked and
clamped including making good ceiling and floor
including supply of all material, labour, T&P etc
required for proper completion of the work.
23.7(b) Same as Item 2(a) above but 20mm dia. Each 37.00 -
23.7(c ) Same as Item 2(a) above but 25mm dia. Each 40.00 -
3 23.99 Fixing gun metal check or non return value of all
nominal base.
(a) 20mm dia Each 45.00 -
(b) 25mm dia Each 50.00 -
4 23.01 Fixing 15mm PVC connection Heavy quality with
brass union Including supply of all material, labour,
T&P etc. and for proper completion of the work.
(a) 30 cms. Length Each 25.00 -
(b) 45 cms. Length Each 30.00 -
5 23.141 Fixing C.P. brass shower rose with 15mm or 20mm
Intel.
(a) 100mm dia Each 45.00 -
6 23.143 Fixing 600 mm x 400mm beveled edge mirror of
superior glass mounted on 6mm thick A.C. Sheet or
plywood sheet and fixed it plastic sleeves with Each 125.00 -
C.P.brass screw and washers.
7 23.148 Fixing C.P. brass towel rail with C.P. brass brackets
fixed to plastic sleeves with C.P. brass screws.
(a) 610mm x 20mm Each 60.00 -
(b) 750mm x 20mm Each 65.00 -
8 Fixing C.P. brass towel rail with C.P. brass brackets
fixed to wood plugs, Plastic sleeves with CP. Brass Each 50.00 -
screws.
9 33.3 Fixing 600mm x 120mm glass shelf and guard rail
complete fix wooden flat with C.P. iron screws. Each 55.00 -
Page 72
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
10 225 Fixing 15mm dia brass ferrule including supply of all
materials, labour and T&P and including boring and Each 120.00 -
taping the main.
11 Same as Item (1) but for external work including earth
in excavation upto required depth and filling watering
and remaining of the same the trenches after laying
pipes in position for completion of the work.
Page 73
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
3 Providing and fixing Polyethelene-Aluminium-
Polyethelene (PE-ALPE) Composite Pressure Pipes
conforming to IS - 15450, U.V. stabilized with carbon
black having thermal stability for hot & cold water
supply, capable to withstand temperature up to 80
0C, including all special fittings of composite material
(engineering plastic blend and brass inserts wherever
required) e.g. elbows, tees, reducers, couplers &
connectors etc., with trenching, refilling and testing of
joints complete as per direction of the engineer in
charge.
External work
A 1216 (16 mm OD) 18.3.1 RM 50.00 180.00
B 1620 (20 mm OD ) 18.3.2 RM 50.00 220.00
C 2025 (25 mm OD ) 18.3.3 RM 50.00 260.00
D 2532 (32 mm OD ) 18.3.4 RM 50.00 335.00
E 3240 (40 mm OD ) 18.3.5 RM 55.00 510.00
F 4050 (50 mm OD ) 18.3.6 RM 55.00 550.00
14 Providing and fixing 3 layer PP-R (Poly propylene
Random copolymer) pipes SDR 7.4, U V stabilized &
anti - microbial fusion welded, having thermal stability
for hot & cold water supply, including all PP – R plain
& brass threaded polypropylene random fittings, i/c
fixing the pipe with clamps at 1.00 m spacing. This
includes testing of joints complete as per direction of
Engineer in Charge.
Page 74
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
16 Providing and fixing 3 layer PP-R (Poly propylene
Random copolymer) pipes, U V stabilized & anti
microbial fusion welded, having thermal stability for
hot & cold water supply, including all PP - R plain &
brass threaded polypropylene random fittings,
including trenching, refilling & testing of joints
complete as per direction of Engineer in Charge.
External work
A PN - 16 Pipe, 16 mm OD (SDR - 7.4) 18.6.1 RM 50.00 100.00
B PN - 16 Pipe, 20 mm OD (SDR - 7.4) 18.6.2 RM 50.00 130.00
C PN - 16 Pipe, 25 mm OD (SDR - 7.4) 18.6.3 RM 50.00 170.00
D PN - 16 Pipe, 32 mm OD (SDR - 7.4) 18.6.4 RM 50.00 240.00
E PN - 16 Pipe, 40 mm OD (SDR - 7.4) 18.6.5 RM 55.00 350.00
F PN - 16 Pipe, 50 mm OD (SDR - 7.4) 18.6.6 RM 55.00 470.00
G PN - 16 Pipe, 63 mm OD (SDR - 7.4) 18.6.7 RM 65.00 705.00
H PN - 16 Pipe, 75 mm OD (SDR - 7.4) 18.6.8 RM 65.00 980.00
I PN - 16 Pipe, 90 mm OD (SDR - 7.4) 18.6.9 RM 85.00 1565.00
J PN - 10 Pipe, 110 mm OD (SDR - 11) 18.6.10 RM 85.00 1695.00
K PN - 10 Pipe, 160 mm OD (SDR - 11) 18.6.11 RM 135.00 3465.00
17 Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply, including all CPVC plain & brass
threaded fittings, including fixing the pipe with clamps
at 1.00 m spacing. This includes jointing of pipes &
fittings with one step CPVC solvent cement and testing
of joints complete as per direction of Engineer in
Charge.
Page 75
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
19 Providing and fixing Chlorinated Polyvinyl Chloride
(CPVC) pipes, having thermal stability for hot & cold
water supply including all CPVC plain & brass
threaded fittings. This includes jointing of pipes &
fittings with one step CPVC solvent cement, trenching,
refilling & testing of joints complete as per direction of
Engineerin-Charge. External work.
Page 76
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
23 Painting G.I. pipes and fittings with synthetic enamel
white paint with two coats over a ready mixed priming
coat, both of approved quality for new work:
Page 77
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
28 Constructing masonry Chamber brick work with
common burnt clay F.P.S.(non modular) bricks of
class designation 150 in cement mortar 1:4 (1 cement
: 4 coarse sand) for sluice valve, with C.I. surface box
100mm top diameter, 160 mm bottom diameter and
180 mm deep ( inside) with chained lid and RCC top
slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20mm nominal size ) , i/c necessary
excavation, foundation concrete 1:5:10 (1 cement : 5
fine sand : 10 graded stone aggregate 40 mm nominal
size) and inside plastering with cement mortar :3 (1
cement : 3 coarse sand) 12 mm thick, finished with a
floating coat of neat cement complete as per standard
design.
Page 78
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
E 250 mm diameter
Class I 18.31.1.1 Each 340.00 11200.00
Class II 18.31.1.2 Each 340.00 11700.00
F 300 mm diameter
Class I 18.31.1.1 Each 390.00 15250.00
Class II 18.31.1.2 Each 390.00 19300.00
31 Providing and fixing uplasticised PVC connection pipe
with brass unions:
A 30 cm length
i) 15 mm nominal bore 18.21.1.1 Each 30.00 65.00
ii) 20 mm nominal bore 18.21.1.2 Each 30.00 70.00
B 45 cm length
i) 15 mm nominal bore 18.21.2.1 Each 30.00 75.00
ii) 20 mm nominal bore 18.21.2.2 Each 30.00 85.00
32 Providing and fixing C.P. brass bib cock of approved
quality conforming to IS:8931.
15 mm nominal bore 18.49.1 Each 45.00 440.00
33 Providing and fixing C.P. brass long nose bib cock of
approved quality conforming to IS standards and
weighing not less than 810 gms.
15 mm nominal bore 18.50.1 Each 45.00 455.00
34 Providing and fixing C.P. brass long body bib cock of
approved quality conforming to IS standards and
weighing not less than 690 gms.
15 mm nominal bore 18.51.1 Each 45.00 485.00
35 Providing and fixing C.P. brass stop cock (concealed) of
standard design and of
approved make conforming to IS:8931.
15 mm nominal bore 18.52.1 Each 45.00 480.00
36 Providing and fixing C.P. brass angle valve for basin
mixer and geyser points of
approved quality conforming to IS:8931
15 mm nominal bore 18.53.1 Each 50.00 505.00
37 Providing and fixing C.P. brass shower rose with 15 or
20 mm inlet:
i) 100 mm diameter 18.22.1 Each 35.00 70.00
ii) 50 mm diameter 18.22.2 1 Each 35.00 90.00
38 Providing and fixing G.I. pipes complete with G.I.
fittings and clamps, i/c cutting and making good the
walls etc.
Page 79
PWD/CP
DSR/P Over All
Sl. WD LABOUR
WD SI Description of the Work Unit Rate
No. Spec. RATE
No (Rs)
No.
41 Providing and fixing on wall face unplasticised Rigid
PVC rain water pipes conforming to IS : 13592 Type A,
including jointing with seal ring conforming to IS :
5382, leaving 10 mm gap for thermal expansion, (i)
Single socketed pipes.
Page 80
CHAPTER- 24
SANITARY FITTING
A Single half stall urinal with 5 litre PVC. automatic flushing 17.5.1
cistern Each 665.00 5665.00
B Range of two half stall urinals with 5 litre PVC. automatic 17.5.2
flushing cistern Each 765.00 8865.00
C Range of three half stall urinals with 10 litre PVC. 17.5.3
automatic flushing cistern Each 865.00 11915.00
D Range of four half stall urinals with 10 litre PVC. 17.5.4
automatic flushing cistern Each 865.00 13615.00
Page 81
CPWD Over All
Sl. DSR SI LABOUR
Description of the Work Spec. Unit Rate
No. No RATE
No. (Rs)
5 Providing and fixing Stainless Steel A ISI 304 (18/8)
kitchen sink as per IS 13983 with C.I. brackets and
stainless steel plug 40 mm, including painting of fittings
and brackets, cutting and making good the walls
wherever required:
Page 82
CPWD Over All
Sl. DSR SI LABOUR
Description of the Work Spec. Unit Rate
No. No RATE
No. (Rs)
11 Providing and fixing plain bend of required degree.
Sand cast iron S&S as per IS : 3989
100 mm dia 17.39.1 Each 40.00 330.00
75 mm dia 17.39.1 Each 35.00 245.00
12 Providing and fixing trap of self cleansing design with
screwed down or hinged grating with or without vent arm
complete, including cost of cutting and making good the
walls and floors:
Page 83
CPWD Over All
Sl. DSR SI LABOUR
Description of the Work Spec. Unit Rate
No. No RATE
No. (Rs)
18 Providing and fixing one piece construction white vitreous
china squatting plate with an integral longitudinal
flushing pipe, white P.V.C. automatic flushing cistern,
with fittings, standard size G.I. / PVC flush pipe for back
and front flush with standard spreader pipes with
fittings, G.I clamps and C.P. brass coupling complete,
including painting of fittings and cutting and making
good the walls and floors
etc. wherever required :
Page 84
CHAPTER- 25
DRAINAGE
(a) Inside size 900 x 800mm and 500mm deep including 19.7.1
C.I. Cover frame. Each 1550.00 8000.00
(b) Inside size 1200 x 1200mm and 1.0meter deep 19.7.2
including C.I. Cover frame. Each 1850.00 16000.00
5 19.8 Extra over Item No. 24.27 for every additional depth of
0.10 metre or part there of main hole.
(a) Size 900 x 800 mm 19.8.1 RM 4500.00
(b) Size 1200 x 900mm 19.8.1 RM 5200.00
Page 85
CPWD Over All
Sl. DSR LABOUR
Description of the Work Spec. Unit Rate
No. SI No RATE
No. (Rs)
6 19.30 Constructing brick masonary chamber for underground
C.I. inspection chamber and bends with bricks in
cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover
with frame (light duty) 455x610 mm internal
dimensions, total weight of cover with frame to be not
less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement :
2 coarse sand : 4 graded stone aggregate 20 mm
nominal size), foundation concrete 1:5:10 (1 cement : 5
fine sand : 10 graded stone aggregate 40 mm nominal
size), inside plastering 12 mm thick with cement mortar
1:3 (1 cement : 3 coarse sand), finished smooth with a
floating coat of neat cement on walls and bed concrete
etc. complete as per standard design :
Page 86
CPWD Over All
Sl. DSR LABOUR
Description of the Work Spec. Unit Rate
No. SI No RATE
No. (Rs)
12 2.10.1 Excavating trenches of required width for pipes, cables,
etc including excavation for sockets, and dressing of
sides, ramming of bottoms, depth up to 1.5 m, including
getting out the excavated soil, and then returning the
soil as required, in layers not exceeding 20 cm in depth,
including consolidating each deposited layer by
ramming, watering, etc. and disposing of surplus
excavated soil as directed, within a lead of 80 m :
Page 87
CHAPTER- 26
ANNUAL REPAIRS
Page 88
CHAPTER- 27
Traffic Sign
Over All
Sl. PWD PWD LABOUR
Desrciption of the Work Unit Rate
No. No. Spec. No. RATE
(Rs)
1 Supplying and instalation of delinators (Road way indicators[
hazard markers, object marker) 80-100 cm. High above ground
level, painted black and white in 15 cm. wide strips, fitted with
80x100 mm rectangular or 75 mm dia circular reflectorised
panel at the top buried of pressed into the ground and
conforming to IRC:79 and the drawing.
Nos. - 1375.00
2 Supply and Fixing of Liner Delineator System (LDS) Panels
made of Micro Prismatic Retro Reflective Sheeting duly
laminated of thin aluminium foil to a unique corrugated shape
to provide Retro Reflection across wide range of observations
and external angles. Eatch LDS panel should be of norminal
length of 33 inch and each ridge shall be approximately 0.34
inch high. Each LDS panel is to be firmly on existing MS
railing MS Sections welding as and when required.
Nos. - 1270.00
3 Supply & Fixing of Bollard made (Single Side) out of
aluminium sheet welded poly shaped to make it monolithic
pillar size 1200 mm high Bollard is having a frame 900x600
mm and 600 mm dia fo fixation made out of 35x35x5 mm
angle iron and from side is fully cover.
Nos. - 5550.00
4 Supply & Fixing of Bollard made (Double Side) out of
aluminium sheet welded poly shaped to make it monolithic
pillar size 1200 mm high Bollard is having a frame 900x600
mm and 600 mm dia fo fixation made out of 35x35x5 mm
angle iron and from side is fully Cover.
Nos. - 8600.00
5 Suppy & Fixing of pavment Makers (Cat Eye) Type X-ASTMD-
4956-04 Avery Dennison/3-M (USA Make) consisting of ASA
plastic housing fitted with tightly aderent plotting compound.
The housing shall contain prismatic two glass coverd prismatic
reflective face to reflect light I/C all tax.
Nos. - 325.00
6 Supply & Fixing of site road studs powerful mode extra bright
Aluminium die cast matt finisish conforming to IS 617:1994
designation 4250 sparkle solar road studs manufactured by
TATA BP solar india or equivalent having high intensity 3x2
Nos. flashing thorugh out night with backup of atlest 4 non
sunlight days amber or red colour all weather resistant with
superior poly corbonate solor cell & side reflectors.
Nos. - 3150.00
7 Providing & erecting direction and place indentification retro-
reflectorised sign as per IRC-67 made of high intensity grade
sheeting vide clause 801.3 fixed over aluminium sheeting 2mm
thick with area nit exceeding 0.9mm Sqm. Supported in a
miled single angle iron post 75x75x6 mm firmly fixed to the
ground by means of property designed foundation with M-15
grade cement concrete 45x45x60cm. below ground level as per
approved drawing Conplete (90x90cm).
Nos. - 7800.00
Madian Marker (MM) Nos. - 750.00
Page 89
Over All
Sl. PWD PWD LABOUR
Desrciption of the Work Unit Rate
No. No. Spec. No. RATE
(Rs)
8 painting Lines dashes, arrows, etc.on roads in two coats on
new work with ready mixed road marking paint conforming to
IS:164 on bituminous surface including cleaning the surface
all dirt, dust and other forein matter,demarcation at site and
traffic control.
Nos. - 80.00
11 Traffic Cone-Providing of red fluorescent with white reflecticve
sleeve traffic cone made of low density polyethylene (LDPE)
material with a square base of 390x390x35 mm and a height
of 770 mm, kg in weight,placed at 1.5 m interval all as per
BS:873. of Mord item no.10.17
Each - 575.00
Page 90
NORMS FOR CONSUMPTION OF MATERIALS FOR BUILDING WORKS
Sl. Cement W.Lime Surkhi Fine San C.Sand Ist. Class Grit B.Ball
ITEM Unit
No. Bag Cu.M Cu.M Cu.M Cum. Brick Cu.M Cu.M
1 2 3 4 5 6 7 8 9 10 11
M-150 B.W in 1:3 lime
1 and surkhi Cum - 0.08 0.24 - - 460 - -
Lime concrete
13 foundation in Cum - 0.15 0.3 - - - - 1.00
100:16:32
Page 91
Sl. Cement W.Lime Surkhi Fine San C.Sand Ist. Class Grit B.Ball
ITEM Unit
No. Bag Cu.M Cu.M Cu.M Cum. Brick Cu.M Cu.M
Struck pointing with
14 1:2 Cement and finne Sqm 0.045 - - 0.003 - - - -
sand.
15 Cement Wash Sqm 0.013 - - - - - - -
Plaster 1:6 Cement &
fine sand :-
16
A. 12 mm thick Sqm 0.063 - - 0.013 - - - -
B. 15 mm thick Sqm 0.095 - - 0.019 - - - -
17 C.C 1:3:6 Cum 4.49 - - - 0.465 0.92 -
18 C.C 1:6:12 Cum 2.26 - - 0.48 - - 1.00 -
19 C.C 1:4:8 Cum 3.44 - - 0.48 - - 0.94 -
20 R.C.C 1:2:4 Cum 6.66 - - - 0.45 - 0.90 -
21 R.C.C 1:1.5:3 Cum 8.66 - - - 0.425 - 0.85 -
Page 92