Professional Documents
Culture Documents
Owner'S Manual & Service Booklet: Maruti Suzuki India Limited
Owner'S Manual & Service Booklet: Maruti Suzuki India Limited
99011M76M01-74E
PEACE OF MIND On Safety, Operation & Maintenance. O RI S
TH
CODE 02/02/2014/5000
AU
ED
Service Division ER
E
VIC
Prepared by
MARUTI SUZUKI INDIA LIMITED
Service Division
February, 2014
Vehicle may break-down, meet with an Avoid driving into or starting the vehicle in a
accident or catch fire due to heavily water logged area. Vehicle may break-
1. Installation of down or engine may fail due to
- High wattage bulbs 1. Water entry into the engine.
- Non genuine lamps / horns 2. Short circuiting of the electrical systems.
- Modified suspension / wheels
- Non genuine parts / accessories etc. If the vehicle is stuck in deep water, do not
2. Retrofitment of LPG / CNG fuel systems/kits. start / crank the vehicle until the level of water
3. Usage of domestic LPG.
drops below the level of exhaust pipe.
4. Short circuiting due to tampering of wiring harness.
NOTE:
IF THE VEHICLE IS SUBMERGED IN WATER, REPORT TO THE NEAREST
CAUTION: DO NOT STORE OR CARRY INFLAMMABLE MATERIALS IN THE VEHICLE. AUTHORIZED WORKSHOP.
“CAUTION”
1. Retro-fitment of LPG / CNG kit may deteriorate vehicle performance, reduce engine & engine
related component’s life and also warranty will be null and void for such vehicles.
2. Do not use domestic LPG/LPG cylinder for your factory fitted LPG vehicles.
3. Usage of domestic LPG for running vehicles is prohibited as per law.
4. Do not remove company fitted LPG/CNG kit to install some other kit. It may affect vehicle
performance and may cause fire.
5. Drive slowly on wet roads. Tires may slip while braking at higher speeds due to aquaplaning.
(reduced contact area between tire and road due to presence of water)
6. Do not leave engine running in garages or confined areas, with passengers inside. This may result in
accumulation of carbon-monoxide in cabin and may lead to suffocation or breathing problems.
7. Do not park vehicle on dry leaves or grass. This may lead to fire due to hot catalytic converter, igniting
the dry leaves/grass.
8. If the vehicle is equipped with CNG/LPG, ensure availability of fire extinguisher in the vehicle all the time.
9. Always wear seat belt at all the times.
10. Do not use mobile phone while driving.
11. Avoid Smoking in the car, live bud thrown in car may cause fire.
12. Do not put any body part under the vehicle when it is supported on a Jack.
13. Do not use non-genuine accessories in your vehicle.
14. Do not fit accessories from unauthorized workshops/sources.
15. Usage of non-approved electrical accessories in your vehicle may result in spark, fire or personal
injury.
CELERIO NEW MODEL 18-12-2013 1ST. FREE INSPECTION COUPON (CUSTOMER’S COPY) (1,000 KM or 1 MONTH) 1ST. F REE I NSPECTIO N C OUPON
WHICHEVER COMES FIRST (DEALER’S COPY) (1,000 KM or 1 MONTH)
JOB MARK: Ö
: Checked OK, A: Adjust, C: Clean, T: Tighten, R: Repair, X: Replace, L: Lubricate
Please see overleaf for special instructions
1. ENGINE JOB 6. FRONT AND REAR SUSPENSION JOB
Model Code*
1. Engine Coolant (Level, Leakage) 1. Struts/shock absorbers (Oil leakage)
2. Engine Oil (Level, Leakage) Chassis No. :
3. Cooling System hoses & connections 7. STEERING
(Leakage, Damage) 1. Steering wheel (Play) Engine No. :
2. All Rods & Arms (Loose, Damage, Wear)
2. FUEL Mileage
3. Power Steering System (Operation)
1. Fuel filter, Fuel tank cap, Fuel lines and
4. Tilt steering (Operation) (if equipped) Date of Delivery
connections (Leakage)
1 1
3. CLUTCH AND TRANSMISSION Date of Inspection
8. ELECTRICAL
1. Clutch pedal (Play) (M/T Only) 1. Battery electrolyte (Level, Leakage) Registration No.
2 Clutch slipping (Dragging, Damage) 2. Lighting system/horn (Operation)
3. Transmission / Differential Oil 3. Wiper (Operation) Service Dealer/Mass Code
(Level, Leakage)
4. Gear Shifter Cable (operation) (M/T Only) Customer Name
9. BODY
4. BRAKE 1. All Latches, Hinges & Locks/Central Locking
1. Brake fluid (Level, Leakage) (Operation) (if equipped)
Address (Please write complete address)
2. Brake pedal (Pedal to wall clearance)
CELERIO NEW MODEL 18-12-2013
Mechanic’s Signature
COST OF MATERIALS AND CONSUMABLES TO BE BORNE BY CUSTOMER
Service Manager’s Signature
* MODEL CODES : ALTO-MRF308/310/410/308C, BALENO-MY416, MARUTI 800-MB308, ESTEEM-MF413,MF415D, GYPSY KING-MG413W,
OMNI-MT308, VERSA-MGA413, WAGON-R-MRD410, ZEN-MH410/MH415D, SWIFT-RS412/RS413/RS413D, Customer’s Signature
SX-4-RW416/416, GRAND VITARA XL7-JA627, ZEN ESTILO-RK410/310/310C, SWIFT DZIRE-RN412/RN413/RN413D,
A-STAR-AMF310, RITZ-A5E412/A5E413D, EECO-MGA412/412C, NEW WAGONR-A1J310/310C, ERTIGA-AVI414/413D, CELERIO-AVH310
CELERIO NEW MODEL 18-12-2013
Stamp of Selling dealer
(Code & Full Address)
Service Division
Maruti Suzuki India Limited
CELERIO NEW MODEL 18-12-2013 2ND. FREE INSPECTION COUPON (CUSTOMER’S COPY) (5,000 KM or 6 MONTHS) 2ND. FREE INSPECTION COUPON
WHICHEVER COMES FIRST (DEALER’S COPY) (5,000 KM or 6 MONTHS)
JOB MARK: Ö
: Checked OK, A: Adjust, C: Clean, T: Tighten, R: Repair, X: Replace, L: Lubricate
1. ENGINE JOB 6. FRONT AND REAR SUSPENSION JOB
1. Engine Coolant (Level, Leakage) 1. Suspension strut/shock absorber(Oil Leakage) Model Code *
2. Engine Oil (Level, Leakage) 2. Suspension arms, Knuckle, Rear spring
3. Cooling System hoses & connections (Damage, Loose) Chassis No. :
(Leakage, Damage) 3. All Nuts & Bolts (Tighten)
4. PCV System (Hoses, Connections, Valve) Engine No. :
7. STEERING
5. Exhaust System (Noise, Leakage)
1. Steering wheel (Play) Mileage
2. All Rods & Arms (Loose, Damage, Wear)
3. Power Steering System (Operation) Date of Delivery
2. FUEL 4. Tilt steering (Operation) (if equipped)
1. Air cleaner (Clean)
2 2
Date of Inspection
2. Fuel filter, Fuel tank cap, Fuel lines and 8. ELECTRICAL
connections (Leakage) 1. Battery electrolyte (Level, Leakage) Registration No.
2. Lighting system/Horn (Operation)
3. CLUTCH AND TRANSMISSION
3. Wiring Harness Connections (Looseness) Service Dealer/Mass Code
1. Clutch pedal (Play) (M/T Only)
2. Clutch slipping (Dragging, Damage) 4. Accessory Socket (operation) (if equipped)
3. Transmission / Differential Oil 5. Wiper (Operation)
(Level Leakage)
9. BODY
4. Gear shifter cables (Operation) (M/T Only) 1. All Latches, Hinges & Locks/Central Locking
5. Drive shaft boots (Damage) (Operation/Lubrication) (if equipped)
CELERIO NEW MODEL 18-12-2013
Service Division
Maruti Suzuki India Limited
CELERIO NEW MODEL 18-12-2013 3RD. FREE INSPECTION COUPON (CUSTOMER’S COPY) (10,000 KM or 12 MONTHS) 3RD. FREE INSPECTION COUPON
WHICHEVER COMES FIRST (DEALER’S COPY) (10,000 KM or 12 MONTHS)
JOB MARK: Ö
: Checked OK, A: Adjust, C: Clean, T: Tighten, R: Repair, X: Replace, L: Lubricate
1. ENGINE JOB 6. FRONT AND REAR SUSPENSION JOB
1. Suspension strut/shock absorber(Oil Leakage) Model Code *
1. Engine Coolant (Level, Leakage)
2. Cooling System hoses & connections 2. Suspension arms, Knuckle, Rear spring
(Leakage, Damage) (Damage, Loose) Chassis No. :
3. Engine oil & oil filter (Replace) 3. All Nuts & Bolts (Tighten)
4. Cylinder head & Manifolds Nuts & Bolts (Tight) Engine No. :
7. STEERING
1. Steering wheel (Play) Mileage
2. FUEL 2. All Rods & Arms (Loose, Damage, Wear)
1. Air cleaner (Clean) 3. Power Steering System (Operation) Date of Delivery
2. Fuel filter, Fuel tank cap, Fuel lines and 4. Tilt steering (operation) (if equipped)
3 3
connections (Leakage) Date of Inspection
8. ELECTRICAL
3. CLUTCH AND TRANSMISSION 1. Battery electrolyte (Level, Leakage) Registration No.
1. Clutch pedal (Play) (M/T Only) 2. Lighting system/Horn (Operation)
2. Clutch slipping (Dragging, Damage) 3. Wiring Harness Connections (Looseness) Service Dealer/Mass Code
3. Transmission / Differential Oil 4. Accessory Socket (Operation) (if equipped)
(Level Leakage) 5. Wiper (Operation)
4. Gear Shifter Cables (Operation) (M/T Only)
5. Universal Joints slack (Inspect) 9. BODY
6. Drive shaft boots (Damage) 1. All Latches, Hinges & Locks/Central Locking
(Operation/Lubrication) (if equipped)
4. BRAKE
CELERIO NEW MODEL 18-12-2013
Service Division
Maruti Suzuki India Limited
MH0-74E
1
MH0-74E
0-1 2
MH0-74E
Indicates a potential hazard that could The circle with a slash in this manual NOTICE
result in death or serious injury. means “Don’t do this” or “Don’t let this Improper installation of mobile
happen”. communication equipment such as
cellular telephones or CB (Citizen’s
CAUTION Band) radios may cause electronic
Indicates a potential hazard that could interference with your vehicle’s
result in minor or moderate injury. ignition system, resulting in vehicle
performance problems. Consult your
MARUTI SUZUKI dealer for advice on
NOTICE installing such mobile communication
Indicates a potential hazard that could equipment.
result in vehicle damage.
NOTE:
WARNING
Indicates special information to make Severe damage may be caused by the
maintenance easier or instructions clearer. use of either poor quality fuel and/or
lubricants not recommended by
MARUTI SUZUKI.
3 0-2
VEHICLE DETAILS MH0-74E
VEHICLE DETAILS
MODEL CHASSIS NO. ENGINE NO. KEY NO. DATE OF ODOMETER BATTERY
DELIVERY READING (KM) MAKE SR. NO ./BATCH CODE
SHOWROOM
Dear Customer
WORKSHOP For any assistance with regard to our product, please contact
General Manager/Works Manager at any of our Dealer or
Authorised Service Station. For additional enquiry you may
contact our Regional office or Service Division. The Addresses
and Phone nos. are given in Service Network section of this
manual.
1-1 4
MH0-74E
(11) any vehicle which has been used for purposes other than (a) make certain that the warranty registration/PDI card was
what it was designed for. completed at the time of delivery of the vehicle;
(12) any damage or deterioration caused by industrial pollution (b) have performed, at his own expenses, by an Maruti
and bird droppings. Suzuki authorised dealer/service station all the service
(13) insignificant defects which do not affect the function of inspections specified in the Maruti Suzuki “Owner’s Manual
the vehicle including without limitation, sound, vibration and Service Booklet” and maintain adequate proof that
and fluid seep. such service inspections have been performed.
(14) any natural wear and tear including without limitation, (c) make certain that the Maruti Suzuki authorised dealer/
aging etc. servise station performing the service inspection has
(15) Installation and usage of Domestic LPG Gas/LPG cylinder. certified the work on the “Maintenance Service Record”
(16) V-belts, hoses and gas leaks (For Maruti Suzuki AC page in the “Owner’s Manual and Service Booklet” and
vehicle). (d) present the Maruti Suzuki “Owner’s Manual and Service
(17) Any vehicle retrofitted with LPG / CNG kits. Booklet” to the authorised Maruti Suzuki dealer whenever
requesting service inspections or warranty service.
(5) Extent of Warranty: If the “Owner’s Manual and Service Booklet” should be lost
This warranty is the entire written warranty given by Maruti or destroyed the owner should consult the authorised Maruti
Suzuki for Maruti Suzuki vehicles and no dealer or its or his Suzuki dealer from whom the vehicle was purchased for
agent or employee is authorised to extend or enlarge this instructions concerning replacement of the “Owner’s Manual
warranty and no dealer or its or his agent or employee is and Service Booklet”.
authorised to make any oral warranty on Maruti Suzuki's
behalf. (8) Disclaimer of Consequential Damage:
Maruti Suzuki reserves the right to add any improvements or Maruti Suzuki assumes no responsibility for loss of vehicle,
change the design of any model at any time with no obligation loss of time, inconvenience or any other indirect incidental
to make the same changes on units previously sold. or consequential damage resulting from the vehicle not being
available to the owner because of any defect covered by this
(6) Warranty Service: warranty.
To obtain warranty service, the complete vehicle must be
presented at the owner’s expenses to any authorised Maruti (9) Change of Owner
Suzuki dealer. Even if ownership of the vehicle changes, the remaining
warranty period is effective for the new owner.
(7) Owner’s Warranty Responsibilities:
It is responsibility of each owner to:
7 2-2
EMISSION WARRANTY MH0-74E
EMISSION WARRANTY
Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki vehicles (apart from the Regular warranty and will run parallel
to the regular product warranty) only in four metropolitan cities (New Delhi, Kolkata, Mumbai and Chennai) with effect from
July 1st, 2001.
Terms:
The Emission Warranty will be applicable for 80,000 kms or 3 years (Which ever comes earlier) from the date of delivery to
the first owner. The remaining warranty terms will be valid in case of any change in ownership provided the production of all
valid document.
Conditions:
1. Under Emission Warranty, Warranty claims will be admitted for a prima facie examination, in case vehicle fails to meet to the
Emission Standard as specified in sub rule (2) of rule no. 115 of Central Motor Vehicles Rules (CMVR), 1989.
2. The warranty claims will only be accepted after examination carried out by Maruti Suzuki or it's dealer which leads to firm conclusions
that the
a) Original settings have not been tempered in any case.
b) Part (as given in Annexure-A) has a manufacturing defect.
c) Vehicle is unable to meet the Emission Standards (as given in 1.), inspite of the vehicle having been maintained and used
in accordance with the instructions as specified in Owner's Manual and Service Booklet and the used fuel and different oils
(Engine oil, Transmission oil, Brake oil etc.) are also as per specification.
3. The method of examination for deciding the warranty of the parts will be at the sole discretion of Maruti Suzuki and it's dea ler
and results of the examination will be final and binding. If after examination, the warrantable condition is not established, Maruti
Suzuki and it's dealer has the right to charge all, or part of the cost of such examination.
4. Under Emission Warranty, the parts (as given in Annexure-A) will be changed free of cost, but the consumables will be charged
as per actual.
5. If the part covered under Emission Warranty or the associated parts, are not independently replaceable, on account of these being
integral parts a complete assembly, Maruti Suzuki and it's dealer will have the sole discretion to replace entire assembly or by
using some of the parts of the system through suitable repair or modifications.
2-3 8
MH0-74E EMISSION WARRANTY
6. Any consequential repairs or replacement of parts which may be found necessary to establish compliance of Emission Warranty,
will not be considered under warranty, unless the same is under product warranty. The consumable will be charged as per actual
under such repair or replacement.
7. Maruti Suzuki will not be responsible for the cost of transportation of the vehicle to the nearest Maruti Suzuki dealer works hop
or any loss due to non-availability of the vehicle during the period of lodging of a warranty claim and examination and/or repa ir
by Maruti Suzuki dealer.
8. Maruti Suzuki will not be responsible for any penalty that may be charged by statutory authorities on account of failure to c omply
with the EMISSION STANDARDS.
9. Emission Warranty will not be affected on the change of owner, provided all the documents are available.
10. All maintenance actions (as specified in the Owner's Manual and Service Booklet) need to be followed and recorded in the man ual
for emission warranty.
11. The customer needs to produce the PUC (Pollution Under Control) certificate valid for the period preceding the test during w hich
the failure is discovered. The receipts (for the maintenance of the vehicle as per specification in Owner's Manual and Service
Booklet from the date of original purchase of the vehicle) will also be required.
2. Vehicle not serviced from Maruti Suzuki authorised workshop as per the schedule specified in the Owner's Manual.
3. Vehicle subjected to abnormal use (accident, motor race, rallies or for the purpose of establishing the records etc.)
6. Tampering with odometer so that the actual kilometer reading can not be read.
7. Use of adulterated fuel and/or unspecified oils (Engine oil, Transmission oil and Brake oil etc.)
9 2-4
EMISSION WARRANTY MH0-74E
Annexure-A
List of parts covered under Emission Warranty
1. Fuel injection Assembly, Pressure Regulator, Throttle Body Assembly.
2. Electronic Control Module (ECM).
3. Intake Manifold.
4. EGR valve.
5. Distributor and internal parts.
6. Ignitions coil.
7. Canister Assembly.
8. Vapour Liquid Separator.
9. Fuel Tank and Filler Cap.
10. PCV (Positive Crankcase Ventilation) Valve.
11. Oil Filler Cap.
12. Catalytic Convertor.
13. Exhaust manifold.
14. All fuel injection System related SENSORS.
15. High Pressure Fuel Pump.
16. Glow Plug.
17. Glow Plug Controller.
18. Maniverter
2-5 10
MH0-74E FUEL RECOMMENDATION
FUEL RECOMMENDATION
You must use unleaded petrol with an NOTE:
octane number (RON) of 91 or higher. If you are not satisfied with the driveability
NOTICE
or fuel economy of your vehicle when you Be careful not to spill fuel containing
Petrol/Ethanol blends
are using a petrol/alcohol blend, you should alcohol while refueling. If fuel is
Blends of unleaded petrol and ethanol (grain
switch back to unleaded petrol containing no spilled on the vehicle body, wipe it up
alcohol), also known as gasohol, are com-
alcohol. immediately. Fuels containing alcohol
mercially available in some areas. Blends
can cause paint damage, which is not
of this type may be used in your vehicle if
covered under the New Vehicle
they are no more than 10% ethanol. Make NOTICE
Limited Warranty.
sure this petrol-ethanol blend has octane The fuel tank has an air space to
ratings no lower than those recommended allow for fuel expansion in hot
for petrol. weather. If you continue to add fuel
Petrol/Methanol blends after the filler nozzle has automatically
Blends of unleaded petrol and methanol shut off or an initial blowback occurs,
(wood alcohol) are also commercially avail- the air chamber will become full.
able in some areas. DO NOT USE fuels Exposure to heat when fully fuelled in
containing more than 5% methanol under this manner will result in leakage due
any circumstances. Fuel system damage or to fuel expansion. To prevent such
vehicle performance problems resulting from fuel leakage, stop filling after the filler
the use of such fuels are not the nozzle has automatically shut off, or
responsibility of MARUTI SUZUKI and may when using an alternative non-
not be covered under the New Vehicle automatic system, initial vent
Warranty. blowback occurs.
Fuels containing 5% or less methanol may
be suitable for use in your vehicle if they
contain cosolvents and corrosion inhibitors.
11 3-1
BEFORE DRIVING MH0-74E
BEFORE DRIVING
Keys ...................................................................................................................................... 4-1
Door Locks .......................................................................................................................... 4-2
Keyless Entry System Transmitter (if equipped) ......................................................... 4-5
Security System (if equipped) ......................................................................................... 4-7
Windows ............................................................................................................................. 4-10
Mirrors ................................................................................................................................ 4-12
Front Seats ........................................................................................................................ 4-14
Rear Seats ......................................................................................................................... 4-14
Seat Belts and Child Restraint Systems ..................................................................... 4-16
Supplemental Restraint System (air bags) (if equipped) ......................................... 4-23
Instrument Cluster ............................................................................................................ 4-30
Speedometer ...................................................................................................................... 4-31
Tachometer (if equipped) ................................................................................................ 4-31
Fuel Gauge ........................................................................................................................ 4-31
Brightness Control ........................................................................................................... 4-32
Information Display .......................................................................................................... 4-32
Warning and Indicator Lights ........................................................................................ 4-40
Lighting Control Lever .................................................................................................... 4-45
Front Fog Light Switch (if equipped) .......................................................................... 4-46
Headlight Leveling Switch .............................................................................................. 4-46
Turn Signal Control Lever . ............................................................................................. 4-47
Hazard Warning Switch ................................................................................................... 4-48
Windshield Wiper and Washer Lever ........................................................................... 4-48
Tilt Steering Lock Lever (if equipped) ......................................................................... 4-50
Horn ..................................................................................................................................... 4-50
Heated Rear Window Switch (if equipped) ................................................................. 4-50
12
MH0-74E BEFORE DRIVING
Door Locks the key toward the rear of the vehicle. Central Door Locking System
(if equipped)
Side Door Locks To lock a front passenger’s door from out-
side the vehicle, turn the lock knob forward, Driver’s door
Driver’s door
then pull and hold the door handle as you
close the door.
(2)
(2)
To lock a rear door from outside the vehi-
cle, turn the lock knob forward and close (1) (3)
the door. You do not need to hold the door
(3)
handle up as you close the door.
(1)
EXAMPLE Door Lock knob
(1) (4)
(4) (2)
76MH0A002
76MH0A001
1) LOCK
1) LOCK 2) UNLOCK
2) UNLOCK 3) Front
3) Front 4) Rear
4) Rear
You can lock and unlock all doors (includ-
To lock a driver’s door from outside the 76MH0A019 ing the tailgate) simultaneously by using the
vehicle: key in the driver’s door lock.
1) LOCK
Insert the key and turn the top of the 2) UNLOCK To lock all doors simultaneously, insert the
key toward the front of the vehicle, or key in the driver’s door lock and turn the
Turn the lock knob forward, then pull To lock a door from inside the vehicle, turn
top of the key toward the front of the vehi-
and hold the door handle as you close the lock knob forward. Turn the lock knob
cle once.
the door. backward to unlock the door. You do not
need to pull and hold the door handle as To unlock all doors simultaneously, insert
To unlock a driver’s door from outside the you close the door. the key in a driver’s door lock and turn the
vehicle, insert the key and turn the top of
4-2 14
MH0-74E BEFORE DRIVING
top of the key toward the rear of the vehi- Child-Proof Locks (rear door)
cle twice. NOTE:
Individual doors can also be EXAMPLE
NOTE:
You can switch the function that unlocks all
UNLOCKED anytime by using
doors from twice operations to once opera- their respective "Door Lock
(2)
tion, and vice versa, via the setting mode Knob" inside the vehicle.
of the information display. For details on If child proof locks are in locked (1)
how to use the information display, refer to position, rear doors cannot be
“Information Display” in this section.
opened from inside.
To unlock the driver’s door only, insert the
key in that door lock and turn the top of NOTE:
the key toward the rear of the vehicle once. If your vehicle is equipped with keyless
entry system, you can also lock or unlock 76MH0A021
EXAMPLE all doors by operating the transmitter. Refer
1) LOCK
to “Keyless Entry System Transmitter” in
2) UNLOCK
this section.
Each of the rear doors is equipped with a
NOTE:
child-proof lock which can be used to help
All doors are automatically unlocked
prevent unwanted opening of the door from
when you turn the ignition switch to the
inside the vehicle. When the lock lever is
“LOCK” position and pull out the key.
in the “LOCK” position (1), the rear door
All doors are automatically locked for can only be opened from outside. When the
safety when the vehicle speed reaches lock lever is in the “UNLOCK” position (2),
15 km/h. the rear door can be opened from inside or
76MH0A020 outside.
You can change the automatic locking
1) LOCK or unlocking function mentioned above WARNING
2) UNLOCK via the setting mode of the information
Be sure to place the child-proof lock
display. For details on how to use the
You can also lock or unlock all doors by in the “LOCK” position whenever
information display, refer to “Information
depressing the front or rear of the switch children are seated in the rear.
Display” in this section.
(3), respectively.
15 4-3
BEFORE DRIVING MH0-74E
from the vehicle in the event of an If you cannot unlatch the tailgate by pulling
accident. Completely closing it also up the tailgate handle (3) due to a dis-
helps keep exhaust gases from enter- charged battery or malfunction, follow the
ing the vehicle. procedures below to unlatch the tailgate
from inside the vehicle.
EXAMPLE 1) Remove the luggage compartment cover 76MH0A137
(2) (if equipped) and fold the rear seat
3) To unlock the tailgate lock, pull the lock
forward for easier access. Refer to
(1) plate (6) up. To open the tailgate, push
“Folding Rear Seats” section for details
the emergency lever (7) sideways. The
on how to fold the rear seat forward.
tailgate will be latched again by simply
EXAMPLE closing the tailgate.
If the tailgate cannot be unlatched by pull-
(3)
ing up the tailgate handle (3), have the
(5)
vehicle inspected by your MARUTI SUZUKI
dealer.
76MH0A086 CAUTION
1) Driver’s door lock Make sure there is no one near the
2) Tailgate lock (4) tailgate when pushing open the tail-
3) Tailgate handle gate from inside the vehicle.
To avoid injury, do not use your
If your vehicle is equipped with the cen- finger to push the emergency lever.
76MH0A099
tral door locking system, you can lock
or unlock the tailgate by using the key 2) Remove the trim (5) of the tailgate.
in the driver’s door lock (1). Push center of the clips (4) and pull
4-4 them out. Then, remove the trim (5). 16
MH0-74E BEFORE DRIVING
Keyless Entry System tion, and vice versa, via the setting mode and then you unlock the doors using the
of the information display. For details on transmitter, the siren will sound 4 times
Transmitter (if equipped) how to use the information display, refer to to remind you. If this happens, check
“Information Display” in this section. whether your vehicle has been broken
EXAMPLE
into while you were away from it.
The turn signal lights will flash once and the
Once you push both of the “LOCK” but-
siren (if your vehicle is equipped with the
ton (1) and “UNLOCK” button (2), then
security system) will sound once when the
you push one of the buttons within 5
doors are locked.
seconds, the siren will not sound.
When the doors are unlocked: However, If you push one of the buttons
The turn signal lights will flash twice and twice within 5 seconds, or push one of
the siren (if your vehicle is equipped with the buttons 5 seconds later, the siren will
(1) the security system) will sound twice. sound.
(2) If the interior light switch is in the You can set whether the siren sounds
“DOOR” position, the interior light will when locking or unlocking the door(s) via
81A184 turn on for about 15 seconds and then the setting mode of the information dis-
1) “LOCK” button fade out. If you insert the key into the play. For details on how to use the infor-
2) “UNLOCK” button ignition switch during this time, the light mation display, refer to “Information
will start to fade out immediately. Display” in this section.
You can lock or unlock all doors (including
the tailgate) simultaneously by operating the Be sure the doors are locked after you NOTE:
transmitter near the vehicle. operate the “LOCK” button. If no door is The maximum operating distance of the
opened within about 30 seconds after the keyless entry system transmitter is about
To lock all doors, push the “LOCK” but- “UNLOCK” button is operated, the doors will 15 m (48 ft.), but this can vary depen-
ton (1) once. automatically lock again. ding on the surroundings, especially near
To unlock only the driver’s door, push other transmitting devices such as radio
the “UNLOCK” button (2) once. NOTE: towers or CB (Citizen’s Band) radios.
To unlock other doors, push the (For models with security system) The door locks cannot be operated with
“UNLOCK” button (2) once again. If you lock the doors using the transmit- the transmitter if the ignition key is
ter when the engine hood is open, the inserted in the ignition switch.
NOTE: siren will sound 3 times to remind you. If any door is open, you cannot lock the
You can switch the function that unlocks all If the security system was triggered due door by operating the transmitter, how-
doors from twice operations to once opera- to an unauthorized entry into the vehicle ever unlock the door.
17 4-5
BEFORE DRIVING MH0-74E
If you lose one of the transmitters key, the ignition switch to the “ON” position to
EXAMPLE
contact your MARUTI SUZUKI dealer as cancel the panic alarm.
soon as possible for a replacement. Be
NOTE: (2)
sure to have your dealer program the
The panic alarm function will not activate
new transmitter code in your vehicle’s
when the key is in the ignition switch.
memory so that the old code is erased.
Replacement of the Battery
NOTICE If the transmitter battery gets discharged
(3)
The transmitter is a sensitive elec- replace the battery.
tronic instrument. To avoid damaging To replace the battery of the transmitter:
the transmitter:
Do not expose it to impacts, mois- EXAMPLE
ture or high temperature such as by 68LM249
leaving it on the dashboard under (1) (3) Lithium disc type battery:
direct sunlight. CR1616 or equivalent
Keep the transmitter away from (2) 3) Put the edge of a flat blade screwdriver
magnetic objects such as a televi- in the slot of the transmitter (2) and pry
sion. it open.
Do not tamper with internal parts 4) Replace the battery (3) so its + terminal
faces the “+” mark of the transmitter.
Panic alarm function (if equipped) 5) Close the transmitter and install it into
This function is to get the attention of oth- the transmitter holder.
ers. 6) Close the transmitter cover, install and
68LM248
Push both of the “LOCK” button (1) and tighten the screw (1).
“UNLOCK” button (2) for more than 3 sec- 1) Remove the screw (1), and open the 7) Make sure the door locks can be oper-
onds. The turn signal lights will blink for transmitter cover. ated with the transmitter.
about 27.5 seconds. Also, the siren will 2) Remove the transmitter (2). 8) Dispose of the used battery properly
sound for about 27.5 seconds at the same according to applicable rules or regula-
time. tions. Do not dispose of lithium batter-
To cancel the panic alarm, press any but- ies with ordinary household trash.
ton (LOCK or UNLOCK). You can also turn
4-6 18
MH0-74E BEFORE DRIVING
WARNING alarm will be triggered if any attempt to system beforehand. Mistakenly triggering
tamper with the vehicle. The shock sensor the alarm may cause a nuisance to others.
Swallowing a lithium battery may can be selected enabled or disabled state, • Even if the security system is armed, you
cause serious internal injury. Do not and sensitivity of each warning can be should still be careful to guard against
allow anyone to swallow a lithium adjusted as desired. To set the shock sensor, theft. Do not leave money or things of value
battery. Keep lithium batteries away ask your MARUTI SUZUKI dealer or use the in the vehicle.
from children and pets. If swallowed, setting mode of the information display.
How to arm the security system (when
contact a physician immediately.
NOTE: enabled)
• The default setting of the shock sensor is in Lock all doors (including the tailgate) using
NOTICE the disabled state. Set to the enabled state the keyless entry system transmitter. The
The transmitter is a sensitive elec- and adjust sensitivity of each warning security system indicator (1) will start blinking
tronic instrument. To avoid damaging according to your preference. For details rapidly, and the security system will be armed
it, do not expose it to dust or mois- on how to use the information display, refer in about 5 seconds.
ture or tamper with internal parts. to “Information Display” in this section.
• Your dealer may have already set the shock While the system is being armed, the
Security System (if equipped) sensor of the vehicle to the enabled state indicator continues to blink at intervals of
before you purchase it. Consult your dealer approximately 2 seconds.
The security system is armed in about 5
for further information.
seconds after you lock all doors (including the With tachometer
tailgate) by using the keyless entry system NOTE:
transmitter. Once the system is armed, any • The security system generates alarms EXAMPLE
attempt to open a door by using any other when any of the predetermined conditions (1)
means (*) than the keyless entry system is met. However, the system does not have
transmitter, or open the engine hood, will any function of blocking unauthorized entry
cause the alarm to be triggered. into the vehicle.
* These means include the following: • Always use the keyless entry system
– The key transmitter to unlock the doors when the
– The lock knob on a door security system has been armed. Using a
– The central door locking switch key instead will trigger the alarm.
Also, in case that you have set the shock • If a person who does not know the security
sensor to enabled state and set sensitivity of system is going to drive the vehicle, we
the pre-warning function and full blast recommend you explain the system and its
operation to the person, or disable the 68LM248
warning function to a level other than 0, the
19 4-7
BEFORE DRIVING MH0-74E
Without tachometer locked, the security system will be armed in will be triggered again if any of the doors or
about 5 seconds if the system is in the engine hood is opened, or the vehicle feels
EXAMPLE enabled state. a shock (if the shock sensor is in the
(1)
• If the security system indicator (1) blinks enabled state), without disarming the
when the ignition switch is in the “ON” security system.
position, there may be something wrong
with the security system. Ask your MARUTI Checking whether the alarm has been
SUZUKI dealer to inspect the system. triggered during parking
If the alarm was triggered and you then turn
How to disarm the security system the ignition switch to “ON” position, the
Simply unlock the doors using the keyless security system indicator will blink rapidly for
entry system transmitter. The security system about 8 seconds and a buzzer will beep 4
indicator will go out, indicating that the times during this period. If this happens,
security system is disarmed. check whether the vehicle has been broken
68LM248 into while you were away from it.
How to stop the alarm
NOTE: Should the alarm be triggered accidentally, Enabling and disabling the security
• To prevent the alarm from being unlock the doors using the keyless entry system
accidentally triggered, avoid arming it while system transmitter, or insert the key in the The security system can be either enabled or
anyone remains inside the vehicle. The ignition switch and turn it to “ON” position. The disabled.
alarm will be triggered if any person inside alarm will then stop.
opens the door or engine hood, or swings When enabled
the vehicle (if the shock sensor is in the • If any of the doors are opened without
NOTE:
enabled state). unlocking by the keyless entry system
• Even after the alarm has stopped, if you
• The security system is not armed when all transmitter, all turn signal lights start to
lock the doors using the keyless entry sys-
doors are locked using the key from blink and the interior buzzer beeps
tem transmitter, the security system will be
outside, or using the door lock knobs or the intermittently. After 5 seconds, the siren will
rearmed with a delay of about 5 seconds.
central door locking switch from inside. sound for about 27.5 seconds. The security
• If you disconnect the battery while the
• If any door is not operated within approxi- system indicator continues to blink during
security system is in the armed condition or
mately 30 seconds after the doors have this time.
the alarm is actually in operation, the alarm
been unlocked using the keyless entry • If the engine hood is opened, all turn signal
will be re-triggered when the battery is then
system transmitter, the doors are automati- lights blink, and the siren sounds for about
reconnected.
cally locked again. When the doors are 27.5 seconds. The security system
• Even after the alarm has stopped at the
indicator continues to blink during this time.
end of the predetermined operation time, it
4-8 20
MH0-74E BEFORE DRIVING
(If the shock sensor is in the enabled state) 1) Sit in the driver’s seat and make sure that 2) Turn the lock knob (1) on the driver’s
• If the vehicle feels a shock, the siren all doors are closed. door rearward (2). Turn the knob on the
sounds for about 2 seconds (pre-warning). • If any door is open, the open door warn- lightning control lever to the OFF
If the vehicle continues to feel a shock, all ing light comes on. position (3). Then, turn the ignition switch
turn signal lights start to blink and the to “ON” position.
interior buzzer beeps intermittently. After 5 EXAMPLE
seconds, the siren will sound for about 27.5 NOTE:
seconds (full blast warning). The security (1) The following steps 3) and 4) must be
system indicator continues to blink during (2)
completed within 15 seconds.
this time.
NOTE: EXAMPLE
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in the
setting mode of the information display, or the
vehicle feels such shock as to be able to
trigger the full blast warning, the full blast 4 times
warning will be triggered preferentially. In this 68LM248
case, the pre-warning will not be triggered.
EXAMPLE
When disabled
When the system is disabled, it stays OFF
disarmed even if you perform any system
arming operation. 68LM248
21 4-9
BEFORE DRIVING MH0-74E
NOTE:
You can also switch the security system
from the enabled state to the disabled
(5) state, and vice versa, via the setting mode
of the information display. For details on
68LM248 how to use the information display, refer to
“Information Display” in this section.
4) Push the lock end (4) (forward end) of the
central door locking switch (5), and then
push the unlock end (6) (backward end).
60G010
Repeat this operation 3 times.
Raise or lower the door windows by turning
Every time you perform the series of the
the handle located on the door panel.
above steps, the state of the security system
changes from the currently selected one to
Electric Window Controls
the other. You can check whether the system
is enabled or disabled by the number of (if equipped)
interior buzzer beeps at the end of the The electric windows can only be operated
procedure as follows. when the ignition switch is in the “ON”
position.
System state Number of beeps
Disabled Once
Enabled 4 times
4-10 22
MH0-74E BEFORE DRIVING
EXAMPLE EXAMPLE
(3)
(4)
81A009
23 4-11
BEFORE DRIVING MH0-74E
68LMT0206
To adjust the mirror, set the selector tab (1) Type 1 Electric Mirrors (if equipped)
to the day position, then move the mirror
up, down or sideways by hand to obtain the EXAMPLE
(1) EXAMPLE
best view.
(3)
When driving at night, you can move the (2)
selector tab to the night position to reduce
glare from the headlights of vehicles behind (4)
(1)
you.
4-14 26
MH0-74E BEFORE DRIVING
27 4-15
BEFORE DRIVING MH0-74E
Lap-Shoulder Belt
Emergency Locking Retractor (ELR)
The seat belt has an emergency locking
retractor (ELR), which is designed to lock MH0-07-014
the seat belt only during a sudden stop or
impact. It also may lock if you pull the belt
across your body very quickly. If this hap-
Low on hips
pens, let the belt go back to unlock it, then
pull the belt across your body more slowly.
MH0-07-014
MH0-07-014
MH0-07-014 MH0-07-014
To unfasten the seat belt, push the button To tighten the belt, pull the free end of the
on the buckle and retract the belt slowly belt across alongside the lap strap.
while attaching a hand to the belt or/and the
latch plate. TO LOOSEN
MH0-07-014
Rear Center Seat Belt
NOTE:
Rear center seat belt is the lap belt.
To identify the center seat belt buckle and
To fasten the belt, pull the latch plate
latch plate in the rear seat, “CENTER” is
attached to the seat belt across your hips
marked on the buckle and latch plate of the
and press it straight into the buckle until you
center lap belt. The buckles are designed
hear a “click”. To reduce the risk of sliding
so a latch plate cannot be inserted into the
under the belt during a collision, position the
wrong buckle.
belt across your lap as low on your hips
Right angle
as possible and adjust it to a snug fit.
MH0-07-014
Driver’s Seat Belt Reminder When the driver doesn’t buckle his or her
seat belt with the ignition switch in the “ON”
NOTICE
(if equipped)
position, the driver’s seat belt reminder light When you move a seatback, make
With tachometer in the instrument cluster will blink until the sure the latch plate is inserted into
driver’s seat belt is buckled. the slit (1) securely so the seat belts
EXAMPLE
are not caught by the seatback, seat
WARNING hinge, or seat latch. This helps
It is absolutely essential that the prevent damage to the belt system.
driver and passengers wear their seat Make sure the belt webbing is not
belts at all times. Persons who are not twisted.
wearing seat belts have a much
Seat Belt Inspection
greater risk of injury if an accident
occurs. Make a regular habit of EXAMPLE
buckling your seat belt before putting
the key in the ignition.
MH0-07-014
EXAMPLE EXAMPLE
MH0-07-014
(1)
Periodically inspect the seat belts to make
sure they work properly and are not dam-
aged. Check the webbing, buckles, latch
plates, retractors, anchorages, and guide
loops. Replace any seat belts which do not
MH0-07-014 MH0-07-014 work properly or are damaged.
4-20 32
MH0-74E BEFORE DRIVING
33 4-21
BEFORE DRIVING MH0-74E
EXAMPLE
MH0-07-014
WARNING
Children could be endangered in a
crash if their child restraints are not
properly secured in the vehicle. When
installing a child restraint system, be
MH0-07-014 sure to follow the instructions below.
Be sure to secure the child in the
WARNING MH0-07-014 restraint system according to the
If your vehicle is equipped with a front manufacturer’s instructions.
passenger air bag, do not install a
rear-facing child restraint in the front
passenger’s seat. If the passenger’s
air bag inflates, a child in a rear-facing
child restraint could be killed or
seriously injured. The back of a rear-
facing child restraint would be too
close to the inflating air bag.
4-22 34
MH0-74E BEFORE DRIVING
Installation with Lap-Shoulder Seat Supplemental Restraint System (air bags) (if equipped)
Belts
ELR type belt EXAMPLE
EXAMPLE 2
1
3
MH0-07-014
Try to move the child restraint system in all Your vehicle is equipped with a Supplemental
WARNING Restraint System consisting of the following
directions to make sure it is securely
This section of the owner’s manual components in addition to a lap-shoulder belt
installed.
describes the protection provided by at each front seating position.
your MARUTI SUZUKI’s SUPPLEMEN-
TAL RESTRAINT SYSTEM (air bags). 1) Driver's front air bag module (if equipped)
Please read and follow ALL these 2) Front passenger's front air bag module (if
instructions carefully to minimize your equipped)
risk of severe injury or death in the 3) Air bag controller (if equipped)
event of a collision. 4) Forward crash sensor (if equipped)
35 4-23
BEFORE DRIVING MH0-74E
Air bag symbol (if equipped) meaning Front Air Bags (if equipped)
WARNING
An air bag supplements, or adds to, EXAMPLE
the crash protection offered by seat
belts. The driver and all passengers
must be properly restrained by wear-
ing seat belts at all times, whether or
not an air bag is mounted at their
seating position, to minimize the risk
of severe injury or death in the event
of a crash.
Driver’s front air bag (if equipped) The driver’s front air bag is located behind Conditions of front air bags deployment
the center pad of the steering wheel and the (inflation)
EXAMPLE front passenger’s front air bag is located
behind the passenger’s side of the dashboard. EXAMPLE
EXAMPLE
MH0-07-014 MH0-07-001
MH0-07-014
Front passenger’s front air bag WARNING In frontal collisions with a fixed wall that
(if equipped) does not move or deform in more than
Do not install a rear-facing child about 25 km/h (15 mph)
EXAMPLE restraint in the front passenger’s seat.
If the passenger’s front air bag
inflates, a child in a rear-facing child (1)
restraint could be killed or severely
injured. The back of a rear-facing child
restraint would be too close to the (1)
inflating air bag.
MH0-07-001
Please refer to the “Seat Belts and Child In collisions such as above at an angle
Restraint Systems” section in this section for of about 30 degrees (1) or less from the
details on securing your child. front
MH0-07-014
37 4-25
BEFORE DRIVING MH0-74E
Conditions of front air bags may inflate Falling into a deep hole or ditch Collision from the rear
Receiving a strong impact to the lower body
of your vehicle, the front air bags will inflate EXAMPLE
EXAMPLE
in many cases.
EXAMPLE
MH0-07-014
MH0-07-014
Collision from the side
Landing hard or falling
MH0-07-014
Front air bags may inflate in a strong EXAMPLE
Hitting a curb or medial strip impact
EXAMPLE EXAMPLE
MH0-07-014
Vehicle rollover
MH0-07-014 MH0-07-014
4-26 38
MH0-74E BEFORE DRIVING
Front air bags may not inflate Collision that the front of your vehicle
EXAMPLE
goes under the bed of a truck etc.
The front air bags may not inflate when the
impact is absorbed since the collision object
moved, vehicle body deformed, or collision EXAMPLE
angle was greater than about 30 degrees
from the front.
MH0-07-014
MH0-07-001
In frontal collisions with a fixed wall that
Approximately 50 km/h (30 mph) or
does not move or deform in less than
lower speed frontal collision to a stopped MH0-07-014
about 25 km/h (15 mph)
vehicle Collision with a utility pole or stumpage
EXAMPLE (1)
MH0-07-001 MH0-07-001
Collision with a fixed wall or guardrail at Collision angle is offset from the vehicle
an angle of greater than about 30 angle (offset collision)
degrees (1) from the front.
MH0-07-014
39 4-27
BEFORE DRIVING MH0-74E
How the system works up straight; do not lean over the steering
wheel or dashboard. Please refer to the
WARNING
In a frontal collision, the crash sensors will
“Front Seat” section and the “Seat Belts and The driver should not lean over the
detect rapid deceleration, and if the con-
Child Restraint Systems” section in this steering wheel. The front passenger
troller judges that the deceleration repre-
section for details on proper seat and seat should not rest his or her body
sents a severe frontal crash, the controller
belt adjustments. against the dashboard, or otherwise
will trigger the inflators. The inflators inflate
get too close to the dashboard. In
the air bags with nitrogen or argon gas. The
EXAMPLE these situations, the out-of-position
inflated air bags provide a cushion for your
occupant would be too close to an
head and upper body. The air bag inflates
inflating air bag, and may suffer
and deflates so quickly that you may not
severe injury.
even realize that it has activated. The air
Do not attach any objects to, or place
bag will neither hinder your view nor make
any objects over, the steering wheel
it harder to exit the vehicle.
or dashboard. Do not place any
Air bags must inflate quickly and forcefully objects between the air bag and the
in order to reduce the chance of serious or driver or front passenger. These
fatal injuries. However, an unavoidable objects may interfere with air bag
consequence of the quick inflation is that operation or may be propelled by the
the air bag may irritate bare skin, such as air bag in the event of a crash. Either
the facial area. Also, upon inflation, a loud MH0-07-014 of these conditions may cause severe
noise will occur and some powder and injury.
smoke will be released. These conditions
are not harmful and do not indicate a fire Note that even though your vehicle may be
in the vehicle. Be aware, however, that moderately damaged in a frontal collision,
some air bag components may be hot for the collision may not have been severe
a while after inflation. enough to trigger the air bags to inflate. If
A seat belt helps keep you in the proper your vehicle sustains ANY front-end dam-
position for maximum protection when an air age, have the air bag system inspected by
bag inflates. Adjust your seat as far back an authorized MARUTI SUZUKI dealer to
as possible while still maintaining control of ensure it is in proper working order.
the vehicle. Sit fully back in your seat; sit
4-28 40
MH0-74E BEFORE DRIVING
Your vehicle is equipped with a diagnostic air bag deployment or could render the air
module which records information about the bag inoperative. Either of these two
air bag system if the air bags deploy in a conditions may result in severe injury.
crash. The module records information
To prevent damage or unintended inflation
about overall system status, which sensors
of the air bag system, be sure the battery
activated the deployment, and for a certain
is disconnected and the ignition switch has
vehicle only, whether the driver’s seat belt
been in the “LOCK” position for at least 90
was in use.
seconds before performing any electrical
Servicing the air bag system service work on your MARUTI SUZUKI. Do
If the air bags inflate, have the air bags and not touch air bag system components or
related components replaced by an authori- wires. The wires are wrapped with yellow
zed MARUTI SUZUKI dealer as soon as tape or yellow tubing, and the couplers are
possible. yellow for easy identification.
If your vehicle ever gets in deep water and Scrapping a vehicle that has an uninflated
the driver’s floor is submerged, the air bag air bag can be hazardous. Ask your dealer,
controller could be damaged. If it does, body repair shop or scrap yard for help with
have the air bag system inspected by the disposal.
MARUTI SUZUKI dealer as soon as
possible.
Special procedures are required for servic-
ing or replacing an air bag. For that rea-
son, only an authorized MARUTI SUZUKI
dealer should be allowed to service or
replace your air bags. Please remind
anyone who services your MARUTI SUZUKI
that it has air bags.
Service on or around air bag components
or wiring must be performed only by an
authorized MARUTI SUZUKI dealer.
Improper service could result in unintended
41 4-29
BEFORE DRIVING MH0-74E
2 6 3
MH0-07-014
Without tachometer
4 6 1 6 5
EXAMPLE
3
MH0-07-014
4-30 42
MH0-74E BEFORE DRIVING
MH0-07-014
43 4-31
BEFORE DRIVING MH0-74E
NOTE:
If you do not turn the brightness control
knob within about 5 seconds of activat-
ing the brightness control display, the
brightness control display will be can-
celed automatically.
MH0-07-014 MH0-07-014
When you reconnect the battery, the
When the ignition switch is turned to the brightness of the instrument panel lights with tachometer
“ON” position, the pointer lights come on. will be reinitialized. Readjust the bright-
Your vehicle has a system to automatically EXAMPLE
ness according to your preference.
dim the brightness of the instrument panel
lights when the position lights or headlights
are on. (B)
When the position lights and/or headlights (D)
are ON, you can control the meter illumina-
tion intensity. (C)
To increase the brightness of the instrument (A) (E)
panel lights, turn the brightness control knob
(1) clockwise. (3)
To reduce the brightness of the instrument
panel lights, turn the brightness control knob
MH0-07-014
(1) counterclockwise.
4-32 44
MH0-74E BEFORE DRIVING
4-34 46
MH0-74E BEFORE DRIVING
The indication on the display may be To change the unit of average fuel con- the current driving range when the ignition
delayed if fuel consumption is greatly sumption, while pushing and holding the trip switch is turned to the “ON” position.
affected by driving conditions. meter selector knob (1), turn the indicator
The driving range shown in the display is
The display shows estimated values. selector knob (2).
the approximate distance you can drive until
Indications may not be the same as
the fuel gauge indicates “E”, based on
actual values. EXAMPLE current driving conditions.
You can change the units that instanta-
neous fuel consumption is displayed in. (Initial When the low fuel warning light comes on,
Refer to “Average fuel consumption” in setting) the display “—” will appear.
this section.
If the low fuel warning light comes on, fill
Average fuel consumption the fuel tank immediately regardless of the
If you selected average fuel consumption value of driving range shown in the display.
the last time you drove the vehicle, the dis-
As the driving range after refueling is cal-
play shows the last value of average fuel
culated based on the most recent driving
consumption from previous driving when the
condition, the value is different each time
ignition switch is turned to the “ON” position.
you refuel.
Unless you reset the value of average fuel MH0-07-014
consumption, the display indicates the value NOTE: NOTE:
of average fuel consumption which includes When you change the units that average If you refuel when the ignition switch is
average fuel consumption during previous fuel consumption is displayed in, the in the “ON” position, the driving range
driving. instantaneous fuel consumption units will may not indicate the correct value.
be changed automatically. When you reconnect the negative (–)
To reset the average fuel consumption to
When you reconnect the negative (–) terminal to the battery, the value of driv-
zero, push and hold the indicator selector
terminal to the battery, the unit of the ing range will be shown after driving for
knob (2) for a while when the display shows
average fuel consumption will be reini- a while.
the average fuel consumption.
tialized. Change the unit again to your
NOTE: preference.
When you reset the indication or reconnect
the negative (–) terminal to the battery, the Driving range
value of average fuel consumption will be If you selected driving range the last time
shown after driving for a while. you drove the vehicle, the display indicates
“—” for a few seconds and then indicates
47 4-35
BEFORE DRIVING MH0-74E
EXAMPLE
(g)
MH0-07-014
MH0-07-001
4-36 48
MH0-74E BEFORE DRIVING
49 4-37
BEFORE DRIVING MH0-74E
4-38 50
MH0-74E BEFORE DRIVING
51 4-39
BEFORE DRIVING MH0-74E
MH0-07-001
4-40 52
MH0-74E BEFORE DRIVING
The light also comes on together with the Seat Belt Warning Light
ABS warning light when the rear brake force
WARNING (if equipped)
control function (proportioning valve function) If any of the following conditions
of the ABS system fails. occur, you should immediately ask
your MARUTI SUZUKI dealer to
If the brake system warning light comes on inspect the brake system.
while you are driving the vehicle, it may If the brake system warning light
mean that there is something wrong with does not go out after the engine
the vehicle’s brake system. If this happens, has been started and the parking MH0-07-001
you should: brake has been fully released.
If the brake system warning light This light blinks as a reminder until the
1) Pull off the road and stop carefully. does not come on when the ignition driver’s seat belt is buckled.
switch is turned to the “ON” For details about the seat belt reminder,
WARNING position. refer to “Seat Belts and Child Restraint
Remember that stopping distance may If the brake system warning light Systems” in this section.
be longer, you may have to push comes on at any time during vehi-
cle operation. AIR BAG” Light (if equipped)
harder on the pedal, and the pedal
may go down farther than normal.
NOTE:
Because the brake system is self-adjusting,
2) Test the brakes by carefully starting and
the fluid level will drop as the brake pads
stopping on the shoulder of the road.
become worn. Replenishing the brake fluid
– If you determine that it is safe, drive
reservoir is considered normal periodic
carefully at low speed to the nearest MH0-07-001
maintenance.
dealer for repairs, or
This light blinks or comes on for several
– Have the vehicle towed to the nearest NOTE: seconds when the ignition switch is turned
dealer for repairs. (Parking Brake Reminder Buzzer) (if to the “ON” position so you can check if the
equipped) light is working.
A buzzer sounds intermittently to remind
you to release the parking brake if you drive The light will come on and stay on if there
the vehicle without releasing the parking is a problem in the air bag system.
brake. Make sure that the parking brake is
fully released and the brake system warning
light turns off.
53 4-41
BEFORE DRIVING MH0-74E
If the warning light comes on briefly then have the emission control system serviced.
WARNING turns off, the system is normal. If the warn- The malfunction indicator light comes on
If the “AIR BAG” light does not blink ing light still stays on, there is something when the ignition switch is turned to “ON”
or come on briefly when the ignition wrong in the system. position to let you know the light is working
switch is turned to the “ON” position, and goes out when the engine is started.
stays on for more than 10 seconds, or If the light and the brake system warning
comes on while driving, the air bag light stay on, or come on simultaneously If the malfunction indicator light comes on
system may not work properly. Have when driving, your ABS system is equipped or blinks when the engine is running, there
the air bag systems inspected with the rear brake force control function is a damage with the emission control
by an authorized MARUTI SUZUKI (proportioning valve function) and there may system. Bring the vehicle to your MARUTI
dealer. be something wrong with both the rear SUZUKI dealer to have the damage fixed.
brake force control function and anti-lock
Also, if the light comes on, there may be
Anti-Lock Brake System (ABS) function of the ABS system.
something wrong with the automated man-
Warning Light (if equipped) If one of these happens, have the system ual transaxle system. Have the system
inspected by your MARUTI SUZUKI dealer. inspected by an authorized MARUTI
If the ABS becomes inoperative, the brake SUZUKI dealer.
system will function as an ordinary brake
system that does not have this ABS sys-
tem. NOTICE
Continuing to drive the vehicle when
MH0-07-001 Malfunction Indicator Light the malfunction indicator light is on or
When the ignition switch is turned to the blinks can cause permanent damage
“ON” position, the light comes on briefly so to the vehicle’s emission control
you can check that the light is working. system, and can affect fuel economy
If the light stays on, or comes on when and driveability.
driving, there may be something wrong with
the ABS. MH0-07-001
4-42 54
MH0-74E BEFORE DRIVING
Transaxle Warning Light This light comes on when the ignition switch cates that the power steering system works
(if equipped) is turned to the “ON” position, and goes out properly.
when the engine is started.
Oil Pressure Light
If this light comes on while driving, the
power steering system may not work prop-
erly. Have the system inspected by your
MARUTI SUZUKI dealer.
MH0-07-001 NOTE:
This light comes on for several seconds Following operations of the steering wheel MH0-07-001
when the ignition switch is turned to the while parking or driving at a very low-speed
may have steering effort bigger gradually. This light comes on when the ignition switch
“ON” position so you can check the light is is turned to the “ON” position, and goes out
working. This is not a malfunction of the steering
system, but the power steering control when the engine is started. The light will
If this light comes on when the engine is come on and remain on if there is
running, there is a problem with the auto- system limits the power assist in order to
insufficient oil pressure. If the light comes
mated manual transaxle system. Ask your prevent them from overheating.
The steering wheel is operated very often. on when driving, pull off the road as soon
MARUTI SUZUKI dealer to have the system as you can and stop the engine.
inspected. The steering wheel is kept in a fully
Check the oil level and add oil if necessary.
turned position for a long while.
NOTE: When the power steering control system If there is enough oil, the lubrication system
If the automated manual transaxle system cool down, the power steering system should be inspected by your MARUTI
temperature becomes too high, this light will back to the original condition. SUZUKI dealer before you drive the vehi-
blink. Stop the vehicle in a safe place and cle again.
let the system cool down. However, repeating these operations could
cause the power steering system damaged. NOTICE
Electric Power Steering Light
NOTE: If you operate the engine with this
If the power steering system does not work light on, severe engine damage can
properly, you will feel heavier to steer but result.
you still will be able to steer. Do not rely on the Oil Pressure
Light to indicate the need to add oil.
NOTE: Be sure to periodically check the
MH0-07-001
If the steering is operated, you may hear engine oil level.
a rubbing noise. This is normal and indi-
55 4-43
BEFORE DRIVING MH0-74E
Charging Light engine is running hot. Avoid driving condi- something wrong with your key or with the
tions that may lead to actual overheating. immobilizer system. Ask your MARUTI
If the light stays on without blinking, then SUZUKI dealer to inspect the system.
the engine is overheating. Follow the
instructions in the “If the Engine Overheats” Open Door Warning Light
of “EMERGENCY SERVICE” section.
NOTICE
MH0-07-001
Continuing to drive the vehicle when
This light comes on when the ignition switch engine overheating is indicated can
is turned to the “ON” position, and goes out result in severe engine damage.
when the engine is started. The light will MH0-07-001
come on and remain on if there is This light remains on until all doors (includ-
Immobilizer System Light
something wrong with the battery charging ing the tailgate) are completely closed.
system. If the light comes on when the
engine is running, the charging system If any door (including the tailgate) is open
should be inspected immediately by your when the vehicle is moving, a ding sounds
MARUTI SUZUKI dealer. to remind you to close all doors completely.
Low Fuel Warning Light
High Engine Coolant Temperature
MH0-07-001
Warning Light (red color)
When the ignition switch is turn to the “ON”
position, this light comes on briefly so you
can check that the light is working. If this
light blinks with the ignition switch is turn
to the “ON” , the engine will not start. MH0-07-001
NOTE: If this light comes on, fill the fuel tank
MH0-07-001
If this light blinks, turn the ignition switch immediately.
When the ignition switch is turned to the to the “LOCK” position, then turn it back to
“ON” position, this light comes on briefly so the “ON” position. When this light comes on, a ding sounds
you can check that the light is working. If If the light still blinks with the ignition switch once to remind you to fill the fuel.
this light blinks while driving, it means the turned to the “ON” position, there may be If you do not fill the fuel, a ding sounds
every time when the ignition switch is turned
4-44 56
MH0-74E BEFORE DRIVING
to the “ON” position. This indicator comes on when headlight Lighting Control Lever
main beams (high beams) are turned on.
NOTE:
The activation point of this light varies Security System Indicator (if EXAMPLE
depending on road conditions (for example, equipped)
slope or curve) and driving conditions
because of fuel moving in the tank.
MH0-07-001
(2)
(1)
MH0-07-001
OFF (1) slightly toward you and release it when you Headlight Leveling Switch
All lights are off. have completed the signal.
(2) Lights “On” reminder (if equipped) EXAMPLE
Front position lights, tail lights, license plate A buzzer/chime sounds to remind you to
light and instrument lights are on, but turn off the lights if they are left on when
headlights are off. the ignition key is removed and the driver’s
door is opened.
(3)
Front position lights, tail lights, license plate Front Fog Light Switch
light, instrument lights and headlights are
(if equipped)
on.
EXAMPLE
EXAMPLE
MH0-07-014
Turn Signal Control Lever Turn Signal Operation Lane change signal
With the ignition switch in the “ON” position,
EXAMPLE move the lever up or down to activate the EXAMPLE
left or right turn signals.
Normal turn signal
EXAMPLE
MH0-07-014 MH0-07-014
MH0-07-014 MH0-07-014
MH0-07-014
Push in the hazard warning switch to To turn the windshield wipers on, move the
activate the hazard warning lights. All turn WARNING lever down to one of the three operating
signal lights and both turn signal indicators positions. In the “INT” position, the wipers
will flash simultaneously. To turn off the To avoid possible injury, do not operate intermittently. The “INT” position is
lights, push the switch again. operate controls by reaching through very convenient for driving in mist or light
Use the hazard warning lights to warn other the steering wheel. rain. In the “LO” position, the wipers operate
traffic during emergency parking or when at a steady low speed. In the “HI” position,
your vehicle could otherwise become a Wiper and Washer Operation the wipers operate at a steady high speed.
traffic hazard. When the ignition switch is in the “ON” To turn off the wipers, move the lever back
position, you can use the wiper/washer lever to the “OFF” position.
or switch (if equipped). Move the lever up and hold it to the “MIST”
position, the windshield wipers will turn on
continuously at low speed.
4-48 60
MH0-74E BEFORE DRIVING
61 4-49
BEFORE DRIVING MH0-74E
Tilt Steering Lock Lever When the rear window is misted, push this
WARNING switch (1) to clear the window.
(if equipped) Never attempt to adjust the steering
wheel while the vehicle is moving or An indicator light will be lit when the
EXAMPLE defogger is on. The defogger will work only
you could lose control of the vehicle.
when the engine is running. To turn off the
defogger, push the (1) switch again.
Horn
EXAMPLE NOTICE
The heated rear window uses a large
amount of electricity. Be sure to turn
off after the window has become
clear.
MH0-07-001
NOTE
Press the horn button of the steering wheel
MH0-07-014 The defogger will work only when the
to sound the horn. The horn will sound with
engine is running.
1) LOCK the ignition switch in any position.
The defogger will automatically turn off
2) UNLOCK
Heated Rear Window Switch after the defogger remains on for 15
(if equipped) minutes to prevent discharging of the
The lock lever is located under the steering
battery.
column. To adjust the steering wheel height: EXAMPLE
1) Push down the lock lever to unlock the
steering column.
2) Adjust the steering wheel to the desired
height and lock the steering column by
pull up the lock lever. (1)
3) Try moving the steering wheel up and
down to make sure it is securely locked
in position.
MH0-07-014
4-50 62
MH0-74E OPERATING YOUR VEHICLE
63
OPERATING YOUR VEHICLE MH0-74E
Avoid breathing exhaust gases. intake selector set to “FRESH AIR”. 1) Make sure that windows, mirrors, lights,
Exhaust gases contain carbon To allow proper operation of your and reflectors are clean and unob-
monoxide, a potentially lethal gas that vehicle’s ventilation system, keep structed.
is colorless and odorless. Since the air inlet grille in front of the 2) Visually check the tires for the following
carbon monoxide is difficult to detect windshield clear of snow, leaves, or points:
by itself, be sure to take the following other obstructions at all times. – the depth of the tread groove
precautions to help prevent carbon Keep the exhaust tailpipe area clear – abnormal wear, cracks and damage
monoxide from entering your vehicle. of snow and other material to help – loose wheel nuts
Do not leave the engine running in reduce the buildup of exhaust gases – existence of foreign material such as
garages or other confined areas. under the vehicle. This is nails, stones, etc.
particularly important when parked Refer to “Tires” in “INSPECTION AND
in blizzard conditions. MAINTENANCE” section for details.
Have the exhaust system inspected 3) Look for fluid and oil leaks.
periodically for damage and leaks.
Any damage or leaks should be
repaired immediately.
5-1 64
MH0-74E OPERATING YOUR VEHICLE
NOTE: Pull the hood release handle inside the More oil is consumed during high-speed
It is normal for water to drip from the air vehicle. Make sure that you cannot open driving and when there is frequent accele-
conditioning system after use. the hood all the way without releasing ration and deceleration. Under high loads,
the secondary latch. Be sure to close your engine also will consume more oil.
4) Make sure the hood is fully closed and
the hood securely after checking for A new engine also consumes more oil,
latched.
proper latch operation. See “All latches, since its pistons, piston rings and cylinder
5) Check the headlights, turn signal lights,
hinges & locks” of “CHASSIS AND walls have not yet become conditioned. New
brake lights and horn for proper
BODY” in the “Periodic Maintenance engines reach the normal level of oil
operation.
Schedule” in the “INSPECTION AND consumption only after approximately 5000
6) Adjust the seat and head restraint (if
MAINTENANCE” section for lubrication km (3000 miles) driving.
equipped).
schedule.
7) Check the brake pedal and the parking Oil consumption:
brake lever. WARNING Max. 1.0 L per 1000 km
8) Adjust the mirrors. (1 Qt. per 600 miles)
9) Make sure that you and all passengers Make sure the hood is fully closed
and latched before driving. If it is not, When judging the amount of oil consump-
have properly fastened your seat belts.
it can fly up unexpectedly during tion, note that the oil may become diluted
10)Make sure that all warning lights come
driving, obstructing your view and and make it difficult to accurately judge the
on as the key is turned to the “ON”
resulting in an accident. true oil level.
position.
As an example, if a vehicle is used for
11)Check all gauges.
Once a month, or each time you fill your repeated shor t trips, and consumes a
12)Make sure that the BRAKE SYSTEM
fuel tank, check the tire pressure using a normal amount of oil, the dipstick may not
WARNING light turns off when the
tire pressure gauge. Also check the tire show any drop in the oil level at all, even
parking brake is released.
pressure of the spare tire. after 1000 km (600 miles) or more of
Once a week, or each time you fill your fuel driving. This is because the oil is gradually
tank, perform the following under-hood Engine Oil Consumption becoming diluted with fuel or moisture,
checks: making it appear that the oil level has not
It is normal for the engine to consume some changed.
1) Engine oil level
engine oil during normal vehicle operation. You should also be aware that the diluting
2) Coolant level
ingredients evaporate out when the vehicle
3) Brake fluid level The amount of engine oil consumed
is subsequently driven at high speeds, such
4) Windshield washer fluid level depends on the viscosity of the oil, the
as on an expressway, making it appear that
5) Battery solution level quality of the oil and the conditions the
oil is excessively consumed after high-speed
6) Hood latch operation vehicle is driven under.
driving.
65 5-2
OPERATING YOUR VEHICLE MH0-74E
EXAMPLE
MH0-07-014 MH0-07-014
67 5-4
OPERATING YOUR VEHICLE MH0-74E
5-5 68
MH0-74E OPERATING YOUR VEHICLE
2) Manual transaxle – Shift into “N” then press down the accelerator pedal to 1/
WARNING (Neutral) and depress the clutch pedal 3 of its travel and try cranking the engine
Do not “ride” the brakes by applying all the way to the floor. Hold the clutch again. Release the key and accelerator
them continuously or resting your foot pedal while starting the engine. pedal when the engine starts.
on the pedal. This will result in Automated manual transaxle – Shift into
overheating of the brakes which could If the engine still does not start, try holding
“N” (Neutral) and depress the brake
cause unpredictable braking action, the accelerator pedal all the way to the floor
pedal. Hold the brake pedal while
longer stopping distances, or while cranking. This should clear the engine
starting the engine.
permanent brake damage. if it is flooded.
WARNING
Accelerator Pedal (3) Using the Transaxle
Make sure that the parking brake is set
This pedal controls the speed of the fully and the transaxle is in Neutral Manual Transaxle
engine. Depressing the accelerator pedal before attempting to start the engine.
increases power output and speed. EXAMPLE
Starting a Cold and Warm Engine
Starting the Engine
With your foot off the accelerator pedal,
Before Starting the Engine crank the engine by turning the ignition key
to “START”. Release the key when the
EXAMPLE
engine starts.
NOTICE
Stop turning the starter immediately
after the engine has started or the
AMT
starter system can be damaged.
MH0-07-014
Do not crank the engine for more
than 15 seconds at a time. If the Starting off
engine doesn’t start on the first try, To start off, depress the clutch pedal all the
wait about 15 seconds before trying way to the floor and shift into 1st gear. After
again. releasing the parking brake, gradually
MH0-07-014
release the clutch. When you hear a change
1) Make sure the parking brake is set fully. If the engine does not start after 15 sec-
in the engine’s sound, slowly press the
onds of cranking, wait about 15 seconds,
69 5-6
OPERATING YOUR VEHICLE MH0-74E
This light will also come on if one of the the vehicle starts slowly without depressing
EXAMPLE
gears cannot be engaged and the system the accelerator pedal. The creeping function
is unable to re-try shifting when you shift is disabled if you depress the brake pedal
R R the gearshift lever from “N” position to “D”, or pull up the parking brake lever.
“M” or “R” position.
NOTE:
- N - N Starting the engine If the driver’s door is opened and/or the
M D M D When starting the engine, always place the parking brake lever is engaged with the
+ + gearshift lever in the “N” position and gear in the “M”, “D” or “R” position, the
depress the brake pedal firmly. The engine creeping function will not operate.
cannot be started unless the gearshift lever
Parking and Stopping the vehicle
is in the “N” position and the brake pedal
Automated manual transaxle does not have
is depressed.
MH0-07-014 a parking position. The vehicle can be
Depress brake pedal indicator parked with the gearshift lever in any
position. When stopping the vehicle, the
gear will be shifted to 1st.
NOTICE
MH0-07-001 A buzzer will sound continuously if
the vehicle is operated with the
MH0-07-001 Clutch operation
gearshift lever in-between of each
This light will come on if you do not You can select either the Drive (D) mode
shift positions. The vehicle will
depress the brake pedal in the following or the Manual (M) mode. Since this vehicle
become inoperative if you continue to
situations. controls clutch operation electronically in
operate the vehicle with the gearshift
When starting the engine. either mode, you do not need to operate the
lever in-between shift positions.
When the engine is on and the gearshift clutch.
lever is shifted from “N” position to “D”, Creeping function Drive (D) mode
“M” or “R” position. This vehicle has a creeping function that When the Drive (D) mode is activated, the
When the ignition switch is in the “ON” helps the vehicle to start smoothly by most appropriate gear position is
position and the engine is off, the engaging the clutch. When the gearshift lever automatically selected upon operation of the
gearshift lever is shifted into any is in any of the positions “D”, “M” or “R”, and accelerator pedal and variation of vehicle
position. you release your foot from the brake pedal, speed.
71 5-8
OPERATING YOUR VEHICLE MH0-74E
Starting off on an uphill/downhill: 2) Release the brake pedal and depress Upshift and downshift:
the accelerator pedal slowly. Even if the
Uphill Upshifting
accelerator pedal is not depressed, the
1) Apply the parking brake firmly so that
clutch will be engaged when the vehicle EXAMPLE
the vehicle does not roll backwards.
speed increases.
2) Shift the gearshift lever to the “D”
position while depressing the brake R
Using engine braking:
pedal. Make sure that the gear position
indicator in the instrumental cluster
When driving on a downhill slope, down- - N
shifting is recommended. So you can use
displays 1st gear. M D
engine braking.
3) Release the brake pedal and depress
By placing the gearshift lever in the “M” +
the accelerator pedal gradually, and
position, the Manual (M) mode is selected,
when the vehicle starts to move, release
and you can shift to a lower gear manually.
the parking brake and depress the
For details of downshift operation, refer to
accelerator pedal to start off.
“Upshift and downshift” in the “Manual (M)
mode”. MH0-07-014
NOTICE
Manual (M) mode Pull the gearshift lever to the “+” direction
On an uphill slope, never hold the and release it. Every time the lever is
The gears are not shifted automatically. To
vehicle at a stop using only the operated, the transaxle is upshifting 1 step
shift the transaxle, the driver must operate
accelerator pedal or the creeping in the order of 1st → 2nd → 3rd → 4th →
the gearshift lever to the “+” or “–” direction.
function. If you perform this operation 5th gear.
As for conventional manual transaxle
for a certain period of time, a warning
vehicles, releasing the accelerator pedal a
buzzer will sound, and in some cases
little may help the transaxle to shift
the engine will stall. This can also
smoothly.
cause excessive damage to the clutch.
Downhill
MH0-07-001
1) Depress the brake pedal and shift the
gearshift lever to the “D” position. Make
sure that the gear is in 1st by checking
the gear position indicator.
73 5-10
OPERATING YOUR VEHICLE MH0-74E
Downshifting NOTE:
To downshift smoothly, the engine runs
WARNING
EXAMPLE fast in some cases. This is done Do not apply the parking brake
intentionally by the system and is not a while driving. Otherwise, it could
R malfunction. cause a skid and you may get
When driving down a hill, downshift and involved in an unexpected accident.
- N use the engine braking appropriately. If
M D necessary, continuous downshifting is
+ possible. However, if downshifting more NOTICE
than 3 steps, gear shifting will take more If the gearshift lever cannot shift into
time. any position, or the gear is changed
When the gear is shifting, a noise can to “N” position automatically when
be heard in some case. This is not a the vehicle speed becomes less than
malfunction. 10 km/h (6 mph), there may be a
MH0-07-014
systematic malfunction. In this case,
Push the gearshift lever to the “–” direction WARNING ask your MARUTI SUZUKI dealer to
and release it. Every time the lever is Be careful when accelerating, inspect the automated manual
operated, the transaxle is downshifted in the upshifting, downshifting or braking transaxle system as soon as possible.
order 5th → 4th → 3rd → 2nd → 1st gear. on a slippery surface. Sudden acce- The manual (M) mode does not
leration or engine braking could upshift even if the engine speed
cause the vehicle to spin or skid. reaches the rev-limit.
To drive down a long or steep hill, The system will not allow shifting
reduce your speed and downshift. up or down to a gear that would
Remember, if you ride the brakes cause engine over-revving or under-
excessively, they may overheat and fail. revving.
While driving the vehicle, do not shift If frequently driving at low speed
MH0-07-001
the gearshift lever to “N” position. using a high gear position, the life
The gear position is displayed on the gear The engine brake may not work and cycle of the clutch may be reduced.
position indicator. The gear position indicator you may get involved in an Frequent downshifting (more than 3
shows the transaxle gear position. Before unexpected accident. If you return the positions consecutively) causes the
starting off, always check the gear position gearshift lever from “N” to “M” reduction of transaxle life.
indicator to make sure that the transaxle is because of unintended shifting, the
engaged in 1st or reverse, then depress the gear position will be shifted according Starting off:
accelerator pedal. to the current vehicle speed. 1) Start the engine as instructed in “Starting
5-11 74
MH0-74E OPERATING YOUR VEHICLE
the engine” in this section. pedal. Depress the accelerator pedal Starting off on an uphill/downhill slope:
2) With your foot on the brake pedal, shift slowly for smooth starting. Uphill
the gearshift lever to the “M” position. 1) Apply the parking brake firmly so that
When the gearshift lever is shifted to the WARNING the vehicle does not roll backwards.
“M” position, the gear will be shifted to 2) Shift the gearshift lever to the “M”
Always keep your foot on the brake
1st. Before starting off, always make position while depressing the brake
pedal or pull up the parking lever
sure that the intended gear is engaged pedal. Make sure that the gear position
while stopped with the engine running.
by checking the gear position indicator, indicator in the instrumental cluster
These operations prevent the vehicle
then depress the accelerator pedal. displays 1st gear.
from starting due to unintended
3) Release the brake pedal and depress
NOTE: activation of the creeping function.
the accelerator pedal gradually, and
If 1st gear cannot be engaged even
when the vehicle starts to move, release
though the gearshift lever has been
shifted from the “N” to the “M” position, NOTICE the parking brake and depress the
Do not operate the system as accelerator pedal to start off.
the system will re-try shifting
automatically. This will take some time, described below. The life cycle of the
noise may be heard from the gears, and clutch may be reduced. NOTICE
shifting gear shock may occur. However, Using the accelerator pedal to hold On an uphill slope, never hold the
they do not indicate a malfunction. the vehicle on an uphill slope vehicle at a stop using only the
The “N” indicator will flash, the depress operation with the gearshift lever in accelerator pedal or creeping function.
brake pedal indicator will come on and the “M” or “D” position. If you If you perform this operation for a
a warning buzzer (long pulse sound) will perform this operation for a certain certain period of time, a warning
sound if any of the following cases occur; period of time, a warning buzzer will buzzer will sound, and in some cases
– If you shift the gearshift lever from the sound. the engine will stall. This can also
“N” to the “M” position without Shifting the gearshift lever to the cause excessive damage to the clutch.
depressing the brake pedal “M”, “D” or “R” position while
– If the system is unable to re-try racing the engine.
Driving at low speed using a high Downhill
shifting
gear. 1) Depress the brake pedal and shift the
You should depress the brake pedal and
Stopping on a slope using the gearshift lever to the “M” position. Check
shift the gearshift lever to “N” position,
creeping function. If you perform the gear position indicator to make sure
then shift to “M” position again a few
this operation for a certain period of that the gear is in 1st.
seconds later.
time, a warning buzzer will sound.
3) Release the parking brake and brake
75 5-12
OPERATING YOUR VEHICLE MH0-74E
2) Release the brake pedal and depress a warning buzzer (long pulse sound) will Stopping
the accelerator pedal slowly. Even sound if any of the following cases The vehicle can be stopped by depressing
though the accelerator pedal is not occur; the brake pedal regardless of the gear
depressed, the clutch will be engaged If you shift the gearshift lever from the position. This is because the clutch is
when the vehicle speed increases. “N” to the “R” position without depressing automatically disengaged to prevent the
the brake pedal engine from stopping.
Backing up
– If the system is unable to re-try shifting If the gearshift lever is in the “D”
After the vehicle has stopped completely,
You should depress the brake pedal and position, the gear will be downshifted to
depress the brake pedal and shift the
shift the gearshift lever to “N” position, 1st when the vehicle stops.
gearshift lever to the “R” position. Depress
then shift to “R” position again a few If the gearshift lever is in the “M”
the accelerator pedal slowly as when
seconds later. position, the gear will be downshifted to
starting off in 1st gear. Before backing up,
The system will not allow shifting to the 1st when the vehicle stops.
make sure that reverse gear is selected by
“R” position if the vehicle speed is over
checking the gear position indicator.
about 3 km/h (2 mph). If the gearshift WARNING
lever is operated under this condition, When stopping, for example, at a
the “N” indicator in the instrument cluster traffic light, be sure to depress the
will blink. However, when the vehicle brake pedal firmly. For your safety,
speed drops below about 3 km/h (2 apply the parking brake, too, when
mph), the gear will be shifted to reverse. stopping on a hill.
Make sure that the vehicle has stopped When racing the engine, make sure
MH0-07-001 completely before shifting to the “R” that the gear is in the “N” position
NOTE: position. by checking the gear position indi-
If reverse gear cannot be engaged even
NOTICE cator. If the accelerator is operated
though the gearshift lever has been
with the gear in any other position,
shifted from the “N” to the “R” position, On a downhill slope, never hold the the vehicle may move resulting in
the system will re-try shifting vehicle at a stop using only the an unexpected accident.
automatically. This will take some time, accelerator pedal or the creeping Do not leave your vehicle unatten-
noise may be heard from the gears, and function. If you perform this operation ded while the engine is running.
shifting gear shock may occur. However, for a certain period of time, a warning
they do not indicate a malfunction. buzzer will sound, and in some cases
The “N” indicator will flash, the depress the engine will stall. This can also
brake pedal indicator will come on and cause excessive damage to the clutch.
5-13 76
MH0-74E OPERATING YOUR VEHICLE
Parking
WARNING Unlike an automatic transaxle, automated
WARNING
manual transaxle does not have a parking If the gear is not engaged properly
When leaving the vehicle, stop the
position. The vehicle can be parked with the and completely before the ignition
engine and park the vehicle with a
gearshift lever in any position. switch is turned off, the vehicle may
gear engaged. If you need to leave
1) Apply the parking brake firmly. not be parked with the gear
the vehicle with the engine running,
2) While depressing the brake pedal, shift engaged. Always confirm the gear
apply the parking brakes firmly, and
the gearshift lever to the “R” position on position by checking the gear
shift the gearshift lever to the “N”
a downhill slope, and to the 1st position position indicator when parking.
position. Otherwise, the vehicle may
in the drive (D) mode or the “M(1)” On a downhill slope, the gear should
move unexpectedly and may cause
position in the manual (M) mode on an be put in reverse, and in 1st gear
an accident.
uphill slope and confirm the gear position on an uphill slope. Otherwise, the
by checking the gear position indicator. vehicle may move, and cause an
NOTICE 3) Stop the engine. unexpected accident. If the gear is
left in the “N” position, the vehicle
On a slope, never hold the vehicle NOTE: cannot be parked with a gear
at a stop using only the accelerator After the engine is stopped, the gear in engaged.
pedal or the creeping function. If the transaxle does not change even if
you perform this operation for a you shift the gearshift lever in any
Parking cancel
certain period of time, a warning position. Always shift the gearshift lever
Depress the brake pedal, turn the ignition
buzzer will sound, and in some before stop the engine.
switch to the “ON” position, and shift the
cases the engine will stall. This can Check the transaxle gear position by
gearshift lever to the “N” position. The gear
also cause excessive damage to the looking at the gear position indicator,
will be disengaged.
clutch. then turn the ignition switch off to stop
If the gearshift lever is operated the engine. Release the brake pedal Warning functions
more than necessary, the system after a few seconds. The gearshift lever A warning buzzer will sound or the indicator
may not allow operation of the will be locked in the position it was in will blink under the following conditions.
gearshift lever for a certain period when the ignition switch was turned off.
of time, and the gear may not be Warning buzzer
shifted appropriately. Therefore, do The clutch is heated due to excessive
not operate the gearshift lever if not load.
necessary. The creeping function is being activated
for a long period of time.
77 5-14
OPERATING YOUR VEHICLE MH0-74E
5-15 78
MH0-74E OPERATING YOUR VEHICLE
WARNING WARNING
If the ABS warning light (1) and the The ABS may not work properly if
Brake system warning light (2) on tires or wheels other than those
the instrument panel simultaneously specified in the owner’s manual are
stays on or comes on when driving, used. This is because the ABS works
both anti-lock function and rear by comparing changes in wheel
brake force control function speed. When replacing tires or wheels,
(proportioning valve function) of the use only the size and type specified
ABS system may have failed. If so, in this owner’s manual.
the rear wheels may easily skid or
the vehicle can even spin in the
worst case when braking on a
slippery road or when hard braking
even on a dry paved road. Ask your
MARUTI SUZUKI dealer to inspect
the ABS system immediately. Drive
carefully, avoiding hard braking as
much as possible.
5-17 80
MH0-74E DRIVING TIPS
DRIVING TIPS
Running-in ............................................................................................................................ 6-1
Catalytic Converter ............................................................................................................. 6-1
Improving Fuel Economy .................................................................................................. 6-2
Highway Driving .................................................................................................................. 6-3
Driving on Hills ................................................................................................................... 6-3
Driving on Slippery Roads ............................................................................................... 6-3
Driving on Wet Roads ....................................................................................................... 6-5
Do's and Don'ts for Safe Driving ................................................................................... 6-5
Margin for Safety ................................................................................................................ 6-8
81
DRIVING TIPS MH0-74E
NOTICE EXAMPLE
The future performance and reliability
of the engine depends on the care
MH0-07-001 and restraint exercised during its early
life. It is especially important to
WARNING
observe the following precautions
Wear Your Seat Belts at All Times. during the initial 960 km (600 miles)
Even though air bags are equipped of vehicle operation.
at the front seating positions, the After starting, do not race the
driver and all passengers should be engine. Warm it up gradually.
properly restrained at all times, Avoid prolonged vehicle operation at
using the seat belts provided. Refer a constant speed. Moving parts will MH0-07-014
to the “Seat Belts and Child break in better if you vary your
Restraint Systems” section for The purpose of the catalytic converter is to
speed. minimize the amount of harmful pollutants
instructions on proper use of the Start off from a stop slowly. Avoid
seat belts. in your vehicle’s exhaust. Use of leaded fuel
full throttle starts. in vehicles equipped with catalytic
Never drive while under the Avoid hard braking, especially
influence of alcohol or other drugs. converters is prohibited, because lead
during the first 320 km (200 miles) deactivates the pollutant-reducing
Alcohol and drugs can seriously of driving.
impair your ability to drive safely, components of the catalyst system.
Do not drive slowly with the
greatly increasing the risk of injury transaxle in a high gear. The converter is designed to last the life of
to yourself and others. You should Drive the vehicle at moderate engine the vehicle under normal usage and when
also avoid driving when you are speeds. unleaded fuel is used. No special maintena-
tired, sick, irritated, or under stress. Do not tow a trailer during the first nce is required on the converter. However,
960 km (600 miles) of vehicle it is very important to keep the engine
operation. properly tuned. Engine misfiring, which can
result from an improperly tuned engine, may
cause overheating of the catalyst. This may
result in permanent heat damage to the
catalyst and other vehicle components.
6-1 82
MH0-74E DRIVING TIPS
83 6-2
DRIVING TIPS MH0-74E
If the air cleaner is clogged with dust, there At high speeds, the vehicle may be
will be greater intake resistance, resulting affected by side winds. Therefore, reduce
WARNING
in decreased power output and increased speed and be prepared for unexpected Try not to hold the brake pedal down
fuel consumption. buffeting, which can occur at the exits too long or too often while going
of tunnels, when passing by a cut of a down a steep or long hill. This could
Keep weight to a minimum cause the brakes to overheat,
hill, or when being overtaken by large
The heavier the load, the more fuel the resulting in reduced braking efficiency.
vehicles, etc.
vehicle consumes. Take out any luggage or Failure to take this precaution could
cargo when it is not necessary.
Driving on Hills result in loss of vehicle control.
Keep tire pressures correct
Underinflation of the tires can waste fuel EXAMPLE
due to increased running resistance of the
NOTICE
tires. Keep your tires inflated to the correct When descending a down hill, NEVER
pressure shown on the label on the driver’s turn the ignition key to the “LOCK”
side door or the driver’s door lock pillar. position. Emission control system
R
damage may result.
Highway Driving - N
at a lower speed than on dry roads due to If Your Vehicle Gets Stuck
possible slippage of tires during braking.
NOTICE
If your vehicle gets stuck in snow, mud, or
When driving on icy, snow-covered, or sand, follow the directions below: Do not continue rocking the vehicle
muddy roads, reduce your speed and avoid 1) Shift the transaxle back and for th for more than a few minutes.
sudden acceleration, abrupt braking, or between a forward range (or first gear Prolonged rocking can cause engine
sharp steering movements. for manual transaxle) and reverse. This overheating or transaxle damage.
will create a rocking motion which may
Tire Chains
give you enough momentum to free the
Tire chains should only be used if they are EXAMPLE
vehicle. Press gently on the accelerator
needed to increase traction or are required
to keep wheel spinning to a minimum
by law. Make sure that the chains you use
wheel rpm. Remove your foot from the
are the correct size for your vehicle’s tires.
accelerator while shifting.
Also make sure that there is enough
Do not race the engine. Excessive wheel
clearance between the fenders and the
spin will cause the tires to dig deeper,
chains as installed on the tires.
making it more difficult to free the
Install the chains on the front tires tightly, vehicle.
according to the chain manufacturer’s 2) If your vehicle remains stuck after a few
instructions. Retighten the chains after minutes of rocking, get another vehicle
driving about 1.0 km (1/2 mile) if necessary. to pull your vehicle out.
With the chains installed, drive slowly. MH0-07-014
WARNING
NOTICE Do not allow anyone to stand near the
If you hear the chains hitting vehicle when you are rocking it, and
against the vehicle body while do not spin the wheels faster than an
driving, stop and tighten them. indicated 40 km/h (25 mph) on the
If your vehicle is equipped with full speedometer. Personal injury and/ or
wheel caps, remove the wheel caps vehicle damage may result from
before installing the chains or the spinning the wheels too fast.
wheel caps can be damaged by the
chain bands.
85 6-4
DRIVING TIPS MH0-74E
DRIVING ON WET ROADS thus enjoy the best and most comfortable
WARNING driving experience.
CAUTION Do not use tires other than those This section contains basic rules for safe
When driving on wet roads, avoid specified by MARUTI SUZUKI. Never driving. Read it carefully for good
driving through large amount of use different sizes or types of tires understanding of the content so that you
standing water on the road. Large on the front and rear wheels. For can enjoy safe and pleasant driving in your
amount of water entering the engine information regarding the specified Maruti Suzuki vehicle.
compartment may cause damage to tires, refer to the Tire Information
the engine and or electrical Label located on the driver’s door
components. lock pillar.
If stuck in deep water, do not start Never use oversized tires or special
till water level drops. shock absorbers and springs to
Water is incompressible substance, raise (jack up) your vehicle. This will
water inside engine is harmful to the change the handling characteristics.
engine. Oversized tires may also rub against
the fender over bumps, causing
vehicle damage or tire failure.
WARNING After driving through water, test the
In addition to following the driving tips brakes while driving at a slow speed
in this section, it is important to to see if they have maintained their
normal effectiveness. If the brakes 60M-04-008
observe the following precautions.
Make sure your tires are in good are less effective than normal, dry Starting
condition and always maintain the them by repeatedly applying the 1. Adjust the driver’s seat for the proper
specified tire pressure. Refer to brakes while driving slowly until the driving posture.
“Tires” in the “INSPECTION AND brakes have regained their normal
2. Adjust the rear view mirror so as to
MAINTENANCE” section for details. effectiveness.
obtain the best possible rear view.
DO’S AND DON’TS FOR SAFE 3. Before moving off, look forward and back
DRIVING to confirm safety.
Exercise care in handling your vehicle. Be 4. Don’t start quickly, for it is dangerous
conscious of not only your own safety but and wastes fuel.
also the safety of others on the road, and
6-5 86
MH0-74E DRIVING TIPS
60M-04-011
5. The higher the speed, the narrower the Night time driving
driver’s visual range becomes. In such 1. Drive more slowly at night than in the
a state, it is difficult to anticipate any daytime, for the visual range is restricted
hazard and the driver feels much at night.
fatigued.
6. Never do sharp handling during high 2. Don’t overtake other vehicles at night.
speed driving. You will lose your control Darkness bothers your sense of speed
over your vehicle. and hinders your judgement on the
7. When overtaking or changing the lane vehicle-to-vehicle distance.
while driving at a high speed, keep an 3. Don’t use the high headlight beam
ample vehicle-to-vehicle distance. unless its use is inevitable. Its dazzle
Long distance driving may blitz the driver of the oncoming
1. Be sure to perform safety checks before vehicle, thus causing an accident. 60M-04-015
starting a trip.
2. Take rest at certain intervals to prevent 4. Always keep the window glasses clean.
an accident which may occur when you Don’t operate the windshield wiper when
are sleepy or tired. the windshield glass is dry or the wiper
blade and glass may get damaged.
6-7 88
MH0-74E DRIVING TIPS
89 6-8
OTHER CONTROLS AND EQUIPMENT MH0-74E
90
MH0-74E OTHER CONTROLS AND EQUIPMENT
Fuel Filler Cap The fuel filler cap is located on the left rear
EXAMPLE
side of the vehicle. The fuel filler door can
EXAMPLE be unlocked by pulling up the opener lever
located on the outboard side of the driver’s
seat and locked by simply closing the door.
EXAMPLE
Open Close
(1)
76MH0A065
NOTE:
76MH0A064
If the cap holder (1) is equipped with the
EXAMPLE fuel filler door, hold the fuel filler cap when
refueling.
68KN048
To reinstall the fuel filler cap:
To remove the fuel filler cap: 1) Turn the cap clockwise until you hear
1) Open the fuel filler door. several clicks.
2) Remove the cap by turning it counter- 2) Close the fuel filler door.
clockwise.
WARNING
CAUTION
Fuel is extremely flammable. Do not
Remove the fuel filler cap slowly. The smoke when refueling, and make sure
fuel may be under pressure and may there are no open flames or sparks in
74LHT0511 spray out, causing injury. the area.
91 7-1
OTHER CONTROLS AND EQUIPMENT MH0-74E
Engine Hood
EXAMPLE
76MH0A067 76MH0A068
2) Push the under-hood release lever up 3) While holding the hood, pull the prop rod
with your finger, as shown in the out from the holding clip, then insert the
illustration. While pushing the lever, lift end of the rod into the designated hole
up the engine hood. in the hood.
CAUTION CAUTION
The release lever can be hot enough The prop rod can be hot enough to
to burn your finger right after driving. burn your finger right after driving.
Touch the lever after it becomes cool Touch the rod after it becomes cool
76MH0A066 enough. enough.
To open the engine hood: Insert the end of the rod into the
hole securely. If the rod drops off,
1) Pull the hood release handle located on NOTICE
the outboard side of the driver’s side. your body may be caught in the
Make sure that the wiper arms are not hood.
This will disengage the engine hood lock
raised before you lift up the engine The rod may drop off when the
halfway.
hood to avoid damaging the wiper hood is hit by a wind. Be careful on
arms and the engine hood. windy days.
7-2 92
MH0-74E OTHER CONTROLS AND EQUIPMENT
To close the engine hood: Sun Visor Card holder (if equipped)
1) Lift the hood up slightly and remove the
prop rod from the hole. Put the prop rod EXAMPLE EXAMPLE
back to the holding clip.
2) Lower the hood close to the bumper,
then let it drop down.
Make sure the hood is securely latched
after closing.
WARNING
Make sure the hood is fully closed
and latched before driving. If it is not,
(1)
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident. 79J161 67LH064
The sun visors can be pulled down to block (1) Card holder
glare coming through the windshield, or they
CAUTION You can put a card in the card holder (1)
can be unhooked and turned to the side to
on the back of the sun visor.
To avoid injury, be sure no part of the block glare coming through the side window.
occupant’s body such as hands or
head is in the path of the hood when NOTICE NOTICE
closing it. When you park your vehicle outdoors
When unhooking and hooking a sun
in direct sunlight or in hot weather, do
visor, be sure to handle it by the hard
not leave plastic cards in the holder.
NOTICE plastic parts or the sun visor can be
The heat may distort them.
damaged.
Pressing the hood from above may
damage the hood.
93 7-3
OTHER CONTROLS AND EQUIPMENT MH0-74E
WARNING
Do not use the mirror while driving
your vehicle or could lose control of
the vehicle.
When using the vanity mirror, do
not move too close to a front air
bag (if equipped) location or lean
against it. If the front air bag is
accidentally inflated, it could hit you
hard. EXAMPLE
76MH0A138
76MH0A069
This light switch has three positions which
function as described below:
7-4 94
MH0-74E OTHER CONTROLS AND EQUIPMENT
NOTE:
The number of doors involved in the lighting
NOTICE NOTICE
operation of the interior light depends on the Use of inappropriate electrical Always close the lid when not in use,
vehicle specification. If there is a switch accessories can cause damage to since entry of foreign material, dust,
(rubber projection) at the door opening as your vehicle’s electrical system. Make water, conductive liquids may damage
shown, the door is involved in the lighting sure that any electrical accessories the audio system or USB device.
operation. The tailgate is also involved in you use are designed to plug into this
this operation even without the rubber type of socket.
Assist Grips (if equipped)
projection.
AUX/USB Socket (if equipped)
Accessory Socket
(if equipped)
EXAMPLE 76MH0A072
95 7-5
OTHER CONTROLS AND EQUIPMENT MH0-74E
EXAMPLE
(6)
(1) (4)
EXAMPLE
76MH0A073
76MH0A074
7-6 96
MH0-74E OTHER CONTROLS AND EQUIPMENT
Instrument Panel Pocket Front Cup Holders (3) Rear Cup Holder (2)
(driver’s side) (1) /
Instrument Panel Pocket (center) (2) WARNING EXAMPLE
WARNING Failure to take the precautions listed
below could cause personal injury or
Do not place any objects which may vehicle damage.
fall out from the pocket when the
vehicle is moving. Be careful when you are using the
Failure to take the precaution may cup holders to hold a cup
result in an object interfering with the containing hot liquid. Spilling out
pedals and causing a loss of vehicle hot liquid can cause burn injury.
control or an accident. Do not use the cup holders to hold
sharp-edged, hard, or breakable
objects. Objects in the cup holders
may be thrown about during a 76MH0A075
sudden stop or impact, and could Open the top to use the cup holder.
cause personal injury.
Be careful not to spill liquid or Rear Door Pocket (4)
insert any foreign materials into the This pocket is provided for holding light and
moving part of the gearshift lever, small items.
or any electrical components. Liquid
or foreign materials may damage Bottle holder
these parts. You should hold a bottle with a cap in the
holder.
97 7-7
OTHER CONTROLS AND EQUIPMENT MH0-74E
grommet(s) to the fastener(s) and position Luggage or other cargo placed in the
the floor mat properly in the footwell. luggage compartment is hidden from view
by a luggage compartment cover.
When you replace the floor mats in your
vehicle with a different type such as
allweather floor mats, we highly recommend 76MH0A104
using Maruti genuine floor mats for proper
fitting. You can hang the shopping bag or other
suitable objects on the hook.
This hook is not designed for large or heavy
7-8 items. 98
MH0-74E OTHER CONTROLS AND EQUIPMENT
3 4
NOTICE 3
Side outlet 0
1 2 3
4
(c)
Temperature-controlled air comes out of the Temperature-controlled air comes out of the
floor outlets and cooler air comes out of the floor outlets, the windshield defroster outlets,
(b) (d) center and side outlets. When the the side defroster outlets and the side
temperature selector (1) is in the fully COLD outlets.
(a) (e) position or fully HOT position, however, the
air from the floor outlets and the air from Defrost (e)
61MM0A019 the center and side outlets will be the same
This is used to select one of the functions temperature.
described below. Heat (c)
Ventilation (a)
76MH0A087
Temperature-controlled air comes out of the
windshield defroster outlets, the side
defroster outlets and the side outlets.
76MH0A085
101 7-11
OTHER CONTROLS AND EQUIPMENT MH0-74E
Air intake selector (4) With this “A/C” switch operation, an indicator to a higher blower speed position increases
light will come on when the airconditioning heating efficiency.
(g) (f)
system is on. To turn off the air conditioning
Quick heating (using recirculated air)
system, push the “A/C” switch again.
The control settings are the same as for
During operation of the air conditioner, you normal heating except you select
may notice slight changes in engine speed. “RECIRCULATED AIR”. If you use this
76MH0A089 These changes are normal, the system is heating method for an extended period of
This selector is used to select the following designed so that the compressor turns on time, the air in the vehicle can become
modes. or off to maintain the desired temperature. contaminated and the windows can become
misty. Therefore, use this method only for
Fresh Air (f) Less operation of the compressor results in
quick heating and change to the normal
When this mode is selected by moving the better fuel economy.
heating method as soon as possible.
lever to right, outside air is used. System Operating Instructions
Head cooled/Feet warmed heating
Recirculated Air (g) Natural ventilation Select “BI-LEVEL” and “FRESH AIR”, the
When this mode is selected by moving the Select “VENTILATION” and “FRESH AIR”, temperature selector to the desired
lever to left, outside air is shut out and the temperature selector to the desired temperature position, and the blower speed
inside air is recirculated. This mode is temperature position, and the blower speed selector to the desired blower speed
suitable when driving through dusty or selector to “OFF”. Fresh air will flow through position. Unless the temperature selector is
polluted air such as in a tunnel, or when the vehicle during driving. in the fully COLD position or fully HOT
attempting to quickly cool down the interior. position, the air that comes out of the center
Forced ventilation and side outlets will be cooler than the air
NOTE: The control settings are the same as for that comes out of the floor outlets.
If you select “RECIRCULATED AIR” for an natural ventilation except you set the blower
extended period of time, the air in the speed selector to a position other than Normal cooling
vehicle can become contaminated. “OFF”. Set the air flow selector to “VENTILATION”,
Therefore, you should occasionally select the temperature selector to the desired
“FRESH AIR”. Normal heating (using outside air) temperature position and the blower speed
Select “HEAT” and “FRESH AIR”, the selector to the desired blower speed
Air conditioning switch (5) temperature selector to the desired position, and turn on the “A/C” switch.
To turn on the air conditioning system, set temperature position and the blower speed Setting the blower speed selector to a
the blower speed selector to a position other selector to the desired blower speed higher blower speed position increases
than “OFF” and push in the “A/C” switch. position. Setting the blower speed selector cooling efficiency.
7-12 102
MH0-74E OTHER CONTROLS AND EQUIPMENT
You can switch the air intake selector to Therefore, you should occasionally select
EXAMPLE
either “FRESH AIR” or “RECIRCULATED “FRESH AIR”.
AIR” as you desire. Choosing “RECIRCULA- If your vehicle has been left in the sun
TED AIR” increases cooling efficiency. with the windows closed, it will cool
faster if you open the windows briefly
Quick cooling (using recirculated air)
while you operate the air conditioner with
The control settings are the same as for
the air intake selector at “FRESH AIR”
normal cooling except you select
and the blower at high speed.
“RECIRCULATED AIR” and the highest
blower speed. Dehumidifying
Set the air flow selector to a desired air flow
NOTE:
selector position, the temperature selector
To turn on the air conditioning system,
to the desired temperature position and the
push in the “A/C” switch and set the 76MH0A090
blower speed selector to the desired blower
blower speed selector to a position other NOTE:
speed position. Also select “FRESH AIR”
than “OFF”. With this “A/C” switch If you need maximum defrosting:
and turn on the “A/C” switch.
operation, an indicator light will come on set the air flow selector to “DEFROST”,
when the air conditioning system is on. NOTE: set the blower speed selector to HIGH,
To turn off the air conditioning system, Because the air conditioner dehumidifies the adjust the temperature selector to the
push the “A/C” switch again. air, turning it on will help keep the windows HOT end,
During operation of the air conditioner, clear, even when blowing heated air using turn on the “A/C” switch, and
you may notice slight changes in engine the “DEFROST” or “HEAT & DEFROST” adjust the side outlets so the air blows
speed. These changes are normal, the functions. on the side windows.
system is designed so that the
compressor turns on or off to maintain Maintenance
the desired temperature. Less operation If you do not use the air conditioner for a
of the compressor results in better fuel long period, such as during winter, it may
economy. not give the best performance when you
star t using it again. To help maintain
NOTE: optimum performance and durability of your
If you select “RECIRCULATED AIR” for air conditioner, it needs to be run
an extended period of time, the air in the periodically. Operate the air conditioner at
vehicle can become contaminated. least once a month for one minute with the
103 7-13
OTHER CONTROLS AND EQUIPMENT MH0-74E
engine idling. This circulates the refrigerant Radio Antenna Audio System (if equipped)
and oil and helps protect the internal
components. EXAMPLE
NOTE:
Your vehicle uses the air conditioning
refrigerant HFC-134a, commonly called “R-
134a”. R-134a replaced R-12 around 1993
for automotive applications. Other
refrigerants are available, including recycled
R-12, but only R-134a should be used in
your vehicle.garage or putting a car cover
over your vehicle.
7-14 104
MH0-74E OTHER CONTROLS AND EQUIPMENT
Safety Information Notes on Discs playback of compact discs bearing mark (A)
shown above.
Precautions
WARNING When the inside of the vehicle is very No other discs can be played.
If you pay extended attention to cold and the player is used soon after Removing the disc Proper way to hold
operating the audio system or viewing switching on the heater, condensation the compact disc
the audio system display while may form on the disc or the optical parts
driving, an accident can occur. If you of the player and proper playback may
set the sound volume too loud, it not be possible. If condensation forms on
could prevent you from being aware the disc, wipe it off with a soft cloth. If
of road and traffic conditions. condensation forms on the optical parts
Keep your eyes on the road and of the player, do not use the player for
52D275
your mind on the drive. Avoid about one hour. This will allow the
paying extended attention to condensation to disappear normally. To remove the compact disc from its
operating the audio system or Driving on extremely bumpy roads which storage case, press down on the center of
viewing the audio system display. cause severe vibrations may cause the case and lift the disc out, holding it
Familiarize yourself with the audio sound to skip. carefully by the edges.
system controls and operation of This unit uses a precision mechanism. Always handle the compact disc by the
the audio system before driving. Even in the event that trouble arises, edges.
Preset your favorite radio stations never open the case, disassemble the Never touch the surface.
before driving so that you can unit, or lubricate the rotating parts.
quickly tune to them using the Please bring the unit to an authorized
presets. MARUTI SUZUKI dealer.
Set the sound volume to a level that
Cautions on Handling
will allow you to continue to be
aware of road and traffic conditions
while driving. 52D347
NOTE:
EXAMPLE
Do not use commercially available CD
(B) protection sheets or discs equipped with
(C) (B) stabilizers, etc.
These may get caught in the internal
mechanism and damage the disc.
52D349
It may be impossible to play CD-R discs
Do not use any solvents such as commer- with this unit due to the recording
cially available cleaners, anti-static spray, or conditions.
thinner to clean compact discs. CD-RW discs cannot be played with this
unit.
52D277 WARNING
New discs may have some roughness This is a class I laser product. Use of
around the edges. The unit may not work controls or adjustments or performan-
or the sound may skip if such discs are ce of procedures other than those
used. Use a ball-point pen (B), etc. to 52D350 specified herein may result in hazard-
remove the roughness (C) from the edges Do not use compact discs that have large ous radiation exposure.
of the disc before inserting it into the unit. scratches, are misshaped, or cracked, etc. Do not open covers and do not
Use of such discs will cause damage or attempt to repair this unit by yourself.
prevent the system from operating properly. Refer servicing to qualified personnel.
52D348
7-16 106
MH0-74E OTHER CONTROLS AND EQUIPMENT
Adjusting bass/treble/balance /fader 1) Press the TUNE FOLDER PUSH Listening to the Radio
1) Press the TUNE FOLDER PUSH SOUND knob (2) until the AVC
SOUND knob (2). adjustment mode is selected. EXAMPLE
Each time the knob is pressed, sound 2) Turn the TUNE FOLDER PUSH SOUND
adjustment will change as follows: knob (2) to select the desired AVC
adjustment level. (Initial setting: LEVEL 2) (3) (1)
(4) (2)
Preset-EQ
Preset-EQ calls up various sound types in
accordance with the listening music type. (5) (7)
Press the seek Up button (3) or the seek When there are fewer than 6 stations
Down button (4). that can be stored even if 1 round of (2) (3)
The unit stops searching for a station at a auto store operation is performed, no (4)
frequency where a broadcast station is station will be stored at the remaining (5)
(2)
(3)
(4) (5)
(1)
MH0-05-005 MH0-05-007 (6)
(D) (D)
MH0-CDC-01
1) TUNE FOLDER PUSH SOUND knob
2) Up button
3) Down button
MH0-05-006
4) RPT button
TRACK REPEAT 5) RDM button
The repeat indicator “RPT” will light. 6) DISP button
The track currently being played will be
played repeatedly. A) Folder number
B) Track number
C) Play time
111 D) DISC type 7-21
OTHER CONTROLS AND EQUIPMENT MH0-74E
Display change
Press the DISP button (6).
Each time the button is pressed, display will
MH0-05-008 change as follows:
FOLDER RANDOM
The random indicator “RDM.F” will light.
The tracks in the current folder will be
played in random order.
7-22 112
MH0-74E OTHER CONTROLS AND EQUIPMENT
Notes on MP3/WMA/AAC Points to remember when making MP3/ data on the same disc, sort and place
WMA/AAC files them in different folders.
What is MP3? Common Do not write files other than MP3/WMA/
MP3 (MPEG audio layer3) is an audio High bit rate and high sampling frequency AAC files and unnecessary folders on a
compression format that has become the are recommended for high quality sounds. disc.
standard format among PC users. Its
Selecting VBR (Variable Bit Rate) is not MP3/WMA/AAC files should be named to
merit is that the original audio data is
recommended. Selecting VBR may meet the standards and the file system
compressed to approximately 1/10 and
cause display of incorrect playing time specifications as shown below.
high sound quality is maintained. This
and jumpiness of playback. The file extension “.mp3”, “.wma” or
means that it is possible to store the data
Playback sound quality varies depending “.m4a” should be assigned to files based
of approximately 10 music CDs on a
on the encoding environment. For on their format independently.
single CD-R/RW disc, which in turn
details, refer to the user manual of the You may encounter a trouble in playing
makes it possible to play music for a long
encoding software and the writing MP3/WMA/AAC files or displaying
time without having to change the disc.
software in use. information of MP3/WMA/AAC files
What is WMA? depending on the writing software or CD
An abbreviation of “Windows Media NOTICE recorder in use.
Audio,” WMA is an audio compression Never assign the “.mp3”, “.wma”, or This unit does not have a play list function.
format developed by Microsoft. “.m4a” file name extension to a file if It is recommended to write discs in Disc-
WMA files for which the DRM (Digital it is not in the MP3/WMA/AAC format at-Once mode even though Multi-session
Rights Management) function is ON file. Failure to observe this may result mode is supported.
cannot be played. in damage to the speaker due to noise
Windows MediaTM and the Windows® production. Compression formats
logo are trademarks or registered MP3
trademarks of Microsoft Corporation in Recording MP3/WMA/AAC files on a CD Bit rate:
the United States and other countries. media MPEG1 Audio Layer III: 32 k - 320 kbps
It is recommended not to write both CD- MPEG2 Audio Layer III: 8 k - 160 kbps
What is AAC? DA files and MP3/WMA/AAC files on a MPEG2.5 Audio Layer III: 8 k - 160 kbps
An abbreviation of “Advanced Audio disc. Sampling frequency:
Coding,” AAC is an audio compression If both CD-DA files and MP3/WMA/AAC MPEG1 Audio Layer III: 32 k/44.1 k/
format used by MPEG2 and MPEG4. files are on the same disc, tracks may 48 kHz
not be played in the correct order or MPEG2 Audio Layer III: 16 k/22.05 k/
some tracks may not be played at all. 24 kHz
When storing both MP3 data and WMA MPEG2.5 Audio Layer III: 8 k/11.025 k/
113 12 kHz 7-23
OTHER CONTROLS AND EQUIPMENT MH0-74E
WMA (Ver. 7, Ver. 8, Ver. 9*) Listening to files stored in a USB A) Folder number
Bit rate: CBR 32 k - 320 kbps device B) Track number
Sampling frequency: 32 k/44.1 k/48 kHz C) Play time
* WMA 9 Professional/LossLess/Voice are D) File type
not supported.
NOTICE
AAC*
Bit rate: ABR 16k - 320 kbbs (3) Do not connect any USB device other
Sampling frequency: 32 k/44.1 k/48 kHz
(4)
(1)
than a USB memory or a USB audio
* Apple Lossless is not supported. (5) (6)
player. Do not connect multiple USB
(2) devices to the USB connector using
Supported file systems (7)
a USB hub, etc. Supplying power to
ISO 9660 Level 1/Level 2, Joliet, Romeo multiple USB devices from the
Maximum number of files/folders connector could cause overheating
Maximum number of files: 512 and smoking.
MH0-07-014
Maximum number of files in a folder: 512
Maximum depth of tree structure: 8 Display Selecting a USB device mode
Maximum number of folders: 255 Press the MEDIA button (1).
(A) (B)
(Root folder is included.) Each time the button is pressed, the mode
will change as follows:
(D) (C)
MH0-D2-001
1) MEDIA button
2) TUNE FOLDER PUSH SOUND knob
3) Up button MH0-05-011
115 7-25
OTHER CONTROLS AND EQUIPMENT MH0-74E
USB Standard Compatibility 1.1/2.0 Full Recording MP3/WMA/AAC files on a Maximum number of files/folders
Speed USB device Maximum number of files: 2500
File System FAT12/16/32, VFAT Playback or display may not be possible Maximum number of files in a folder: 255
Maximum current less than 1.0 A depending on the type of USB device in Maximum depth of tree structure: 8
• If devices such as USB hub, extension use or the condition of the recording. Maximum number of folders: 255
cable are connected to the audio system, Depending on the connected USB (Root folder is included.)
it may not be recognized. In such case memory, the files may be played in
connect the USB device directly to the different order from the order that the Listening to an iPod®
audio system. files were stored.
• Devices such as MP3 player/Mobile
Compression formats
phone/digital camera may not be reco-
gnized by the audio system for playing MP3
music. Bit rate: (3)
periods of time in places inside the MPEG2 Audio Layer III: 16 k/22.05 k/24
vehicle where the temperature can rise kHz 76MH0A098
too high. MPEG2.5 Audio Layer III: 8 k/11.025 k/
12 kHz Display
Back up any important data beforehand.
We cannot accept responsibility for any (A)
WMA (Ver. 7, Ver. 8, Ver. 9*)
lost data.
Bit rate: CBR 32 k -320 kbps
It is recommended not to connect a USB
Sampling frequency: 32 k/44.1 k/48 kHz
device that contains data files other than
* WMA 9 Professional/LossLess/Voice are
MP3/WMA/AAC format. (B) (C)
not supported.
MH0-D2-IPOD-001
AAC* 1) MEDIA button
Bit rate: ABR 16k - 320 kbbs 2) TUNE FOLDER PUSH SOUND knob
Sampling frequency: 32 k/44.1 k/48 kHz 3) Up button
* Apple Lossless is not supported. 4) Down button
7-26 116
MH0-74E OTHER CONTROLS AND EQUIPMENT
Playing Mode selection iPod® touch (3rd generation) not be shut down when it is being
1) Press the button numbered [6] of the iPod® touch (2nd generation) connected and may result in battery
Preset buttons (8) for 1 second or iPod® touch (1st generation) depletion.
longer. iPod® classic Please do not connect iPod® accesso-
2) Turn the TUNE FOLDER PUSH SOUND iPod® nano (7th generation) ries such as an iPod® remote control or
knob (2). iPod® nano (6th generation) headphones while connecting the iPod®
Each time the knob is turned, the mode iPod® nano (5th generation) with the unit. The unit may not operate
will change as follows: iPod® nano (4th generation) correctly.
iPod® nano (3rd generation)
iPod® nano (2nd generation)
AUX Function
iPod® nano (1st generation)
iPod® (5th generation)
iPhone® 5
iPhone® 4S
iPhone® 4
iPhone® 3GS (1)
iPhone® 3G
iPhone®
* Some functions may not be available
depending on the model of iPod®.
MH0-05-015 * iPod® is a trademark of Apple Inc., regi-
stered in the U.S. and other countries.
3) Press the TUNE FOLDER PUSH SOUND * iPhone® is a trademark of Apple Inc., 76MH0A100
knob (2) to select the desired mode. registered in the U.S. and other 1) MEDIA button
NOTE: countries. AUX connection
When the button numbere d [6] of the * Apple is not responsible for the operation To listen to auxiliary audio sources (sold
Preset buttons (8) is pressed, the of this device or its compliance with separately) through the unit, follow the
previous mode will be displayed. safety and regulatory standards. instruction below.
iPod® connection 1) Connect the auxiliary audio source to the
Notes on iPod® AUX/USB socket (separately attached)
Supported iPod® Make sure to detach the iPod® after
pressing the engine switch to change the with an AUX cable.
iPod® touch (5th generation)
iPod® touch (4rd generation) ignition mode to LOCK. The iPod® may
7-28 118
MH0-74E OTHER CONTROLS AND EQUIPMENT
(1) (2)
(7)
MH0-05-011
CAUTION (3)
76MH0A132
Before connection, mute the unit,
and also keep the volume of the 76MH0A102 4) Bluetooth® setup button
auxiliary audio source within a 1) TUNE FOLDER PUSH SOUND knob 5) Off Hook button
range that will not cause distortion. 2) VOL PUSH POWER knob 6) On Hook button
When the audio source is turned off, 3) Preset buttons 7) VOL switch
noise may be emitted. Be sure to
turn off the unit or switch to Steering switch Phone registration
another mode before turning off the To use the hands-free function with this
audio source. unit, it required to register the phone in
advance.
NOTE:
Please consult your place of purchase (4) NOTE:
for details about whether a given Up to 5 phones can be registered.
auxiliary audio source can be connected To set up a new phone, disconnect the
and the proper auxiliary cord to use. (5) audio player from the unit. Connect the
The volume and tone controls of the audio player again after phone setup is
auxiliary audio source can be adjusted (6)
completed if necessary.
on the unit. When failed to establish the pairing
In AUX mode, the volume setting is within 120 seconds, the connecting
different from another mode. 76MH0A140 operation will be canceled. Please try
119 7-29
OTHER CONTROLS AND EQUIPMENT MH0-74E
again or refer to the manual of the Rejecting a call (only for supported 2) Turn the TUNE FOLDER PUSH SOUND
phone in use for how to establish the models) knob (1) to select “Setup Telephone”,
pairing with the phone. Press the On Hook button (6) to reject a in- and press the knob (1) to determine the
coming call. selection.
1) Press the Bluetooth® setup button (4).
3) Turn the TUNE FOLDER PUSH SOUND
The Bluetooth® setup menu will be Adjusting the listening volume
knob (1) to select “Sound Setting”, and
displayed. Turn the VOL PUSH POWER knob (2)
press the knob (1) to determine the
2) Turn the TUNE FOLDER PUSH SOUND during a call.
selection.
knob (1) to select “Setup Bluetooth”, and Turning it clockwise increases the
4) Turn the TUNE FOLDER PUSH SOUND
press the knob (1) to determine the volume; turning it counterclockwise
knob (1) to select “Call Volume” or
selection. decreases the volume.
“Ringtone Volume”, and press the knob
3) Turn the TUNE FOLDER PUSH SOUND Press the VOL switch (7) during a call.
(1) to determine the selection.
knob (1) to select “Pairing”, and press Pressing “+” of the switch increases the
The current call or ringtone volume will
the knob (1) to determine the selection. volume, pressing “-” of the switch
be displayed.
4) Select “CAR AUDIO” from the decreases the volume.
5) Turn the TUNE FOLDER PUSH SOUND
Bluetooth® menu of the phone and
Adjusting the ring volume knob (1) to select desired call or
establish the pairing.
Turn the VOL PUSH POWER knob (2) ringtone volume, and press the knob (1)
Refer to the manual of the phone in use
while a call coming in. to determine the selection.
for further information.
Turning it clockwise increases the
5) Enter the Passkey displayed on the unit
volume; turning it counterclockwise NOTE:
to the phone.
decreases the volume. When selecting “Go Back”, the previous
6) Press the On Hook button (6).
Press the VOL switch (7) during a call. menu will be displayed.
NOTE: Pressing “+” of the switch increases the
When selecting “Go Back”, the previous volume, pressing “-” of the switch Selecting the Ringtone
menu will be displayed. decreases the volume. Follow the instructions below to select a
When additionall y registering a phone, ringtone.
Adjusting the call or ringtone volume 1) Press the Bluetooth® setup button (4).
operate the same step from 1).
Follow the instructions below to adjust the The Bluetooth® setup menu will be
Receiving a call call or ringtone volume. displayed.
Press the Off Hook button (5) to receive a 1) Press the Bluetooth® setup button (4). 2) Turn the TUNE FOLDER PUSH SOUND
call. The Bluetooth® setup menu will be knob (1) to select “Setup Telephone”,
Ending a call displayed. and press the knob (1) to determine the
Press the On Hook button (6) to end a call. selection.
7-30 120
MH0-74E OTHER CONTROLS AND EQUIPMENT
3) Turn the TUNE FOLDER PUSH SOUND To dial from the dialed history or the 3) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Sound Setting”, and received history, select “Missed Calls”, knob (1) to select “Delete History”, and
press the knob (1) to determine the “Incoming Calls” or “Outgoing Calls” press the knob (1) to determine the
selection. respectively. selection.
4) Turn the TUNE FOLDER PUSH SOUND 3) Turn the TUNE FOLDER PUSH SOUND 4) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Ringtone”, and press knob (1) to select the desired number, knob (1) to select “Missed Calls”,
the knob (1) to determine the selection. and press the knob (1) to determine the “Incoming Calls”, or “Outgoing Calls”,
The current ringtone will be sounded. selection. and press the knob (1) to determine the
5) Turn the TUNE FOLDER PUSH SOUND 4) Turn the TUNE FOLDER PUSH SOUND selection.
knob (1) to select desired ringtone, and knob (1) to select “Dial”, and press the 5) Turn the TUNE FOLDER PUSH SOUND
press the knob (1) to determine the knob (1) or the Off Hook button (5) to knob (1) to select a number to be
selection. dial to the selected number. deleted or “ALL”, and press the knob (1)
to determine the selection.
NOTE: NOTE:
6) Turn the TUNE FOLDER PUSH SOUND
When selecting “Go Back”, the previous When selecting “Go Back”, the previous
knob (1) to select “Delete?” or “Delete
menu will be displayed. menu will be displayed.
All?”, and press the knob (1) to
Pressing “Confirm” after selecting “Add
Dialing using Missed/Incoming/ determine the selection.
Speed Dial” can register the selected
Outgoing Calls 7) Turn the TUNE FOLDER PUSH SOUND
number in the speed dial.
Follow the instructions below to dial to the knob (1) to select “Confirm”, and press
Pressing “Confirm” after selecting
last dialed number again. the knob (1) to complete the deletion.
“Delete” can delete the selected number
NOTE: from the call history. NOTE:
Up to 10 phone numbers of the latest calls When selecting “Go Back”, the previous
Deletion of call history menu will be displayed.
can be stored. (10 each for dialed, received
Follow the instructions below to delete a
and missed calls) Registration in Phonebook
missed/incoming/outgoing call history.
1) Press the Off Hook button (5). Registration of numbers in the phonebook.
1) Press the Bluetooth® setup button (4).
The Bluetooth® phonebook menu will be Follow the instructions below to register
The Bluetooth® setup menu will be
displayed. phone numbers in the Phonebook of the
displayed.
2) Turn the TUNE FOLDER PUSH SOUND unit.
2) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Missed Calls”, 1) Press the Bluetooth® setup button (4).
knob (1) to select “Setup Phonebook”,
“Incoming Calls” or “Outgoing Calls”, and The Bluetooth® setup menu will be
and press the knob (1) to determine the
press the knob (1) to determine the displayed.
selection.
selection.
121 7-31
OTHER CONTROLS AND EQUIPMENT MH0-74E
2) Turn the TUNE FOLDER PUSH SOUND Transfer of call history (Call History) 2) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Setup Telephone”, Follow the instructions below to transfer call knob (1) to select “Phonebook”, and
and press the knob (1) to determine the history of the registered phone. press the knob (1) to determine the
selection. 1) Press the Bluetooth® setup button (4). selection.
3) Turn the TUNE FOLDER PUSH SOUND The Bluetooth® setup menu will be 3) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Setup Phonebook”, displayed. knob (1) to select the initial of the name
and press the knob (1) to determine the 2) Turn the TUNE FOLDER PUSH SOUND you would like to make a call, and press
selection. knob (1) to select “Setup Telephone”, the knob (1) to determine the selection.
4) Turn the TUNE FOLDER PUSH SOUND and press the knob (1) to determine the The registered numbers will be displayed
knob (1) to select “Add Contacts”, and selection. in sequence. If names have been
press the knob (1) to determine the 3) Turn the TUNE FOLDER PUSH SOUND registered together with numbers, the
selection. knob (1) to select “Call History”, and names will be displayed.
5) Turn the TUNE FOLDER PUSH SOUND press the knob (1) to determine the 4) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Overwrite All” or “Add selection. knob (1) to select “Dial”, and press the
One Contact”, and press the knob (1) to 4) Turn the TUNE FOLDER PUSH SOUND knob (1) to determine the selection.
determine the selection. knob (1) to select “Call History?”, and 5) Press the Off Hook button (5).
The “Rest of Memory XXXX: Ok?” will press the knob (1) to determine the The displayed number or the number
be displayed. selection. registered with the displayed name will
6) Press or turn the TUNE FOLDER PUSH 5) Turn the TUNE FOLDER PUSH SOUND be dialed.
SOUND knob (1) to select “Confirm”, knob (1) to select “Confirm”, and press Deletion of registered data (Delete
and press the knob (1) to determine the the knob (1) to transfer the call history Entry)
selection. from the phone. Follow the instructions below to delete a
7) Transfer contacts from the phone. number registered in Phonebook.
NOTE:
When the registration is completed, the 1) Press the Bluetooth® setup button (4).
When selecting “Go Back”, the previous
“Setup Phonebook” will be displayed. The Bluetooth® setup menu will be
menu will be displayed.
NOTE: displayed.
Making a call by Phonebook 2) Turn the TUNE FOLDER PUSH SOUND
When selecting “Go Back” the previous
Follow the instructions below to dial a knob (1) to select “Setup Telephone”,
menu will be displayed.
number registered in Phonebook. and press the knob (1) to determine the
Up to 1000 numbers can be registered
1) Press the Off Hook button (5). selection.
in Phonebook.
The Bluetooth® phonebook menu will be
displayed.
7-32 122
MH0-74E OTHER CONTROLS AND EQUIPMENT
3) Turn the TUNE FOLDER PUSH SOUND 3) Turn the TUNE FOLDER PUSH SOUND number assigned to each of the Preset
knob (1) to select “Setup Phonebook”, knob (1) to select “Setup Phonebook”, buttons (3).
and press the knob (1) to determine the and press the knob (1) to determine the 1) Press the Off Hook button (5).
selection. selection. The Bluetooth® phonebook menu will be
4) Turn the TUNE FOLDER PUSH SOUND 4) Turn the TUNE FOLDER PUSH SOUND displayed.
knob (1) to select “Delete Contacts”, and knob (1) to select “Add Speed Dial”, and 2) Turn the TUNE FOLDER PUSH SOUND
press the knob (1) to determine the press the knob (1) to determine the knob (1) to select “Speed Dials”, and
selection. selection. press the knob (1) to determine the
5) Turn the TUNE FOLDER PUSH SOUND 5) Turn the TUNE FOLDER PUSH SOUND selection.
knob (1) to select a number to be knob (1) to select a number to be 3) Press one of the Preset buttons (3).
deleted, and press the knob (1) to assigned, and press the knob (1) to When no number is assigned, “No Entry”
determine the selection. determine the selection. is displayed.
6) Turn the TUNE FOLDER PUSH SOUND 6) Turn the TUNE FOLDER PUSH SOUND 4) Press the Off Hook button (5).
knob (1) to select “Delete?”, and press knob (1) to select “Choose Preset”, and The selected number will be dialed.
the knob (1) to determine the selection. press the knob (1) to determine the
Deletion of speed dial (Del Speed Dial)
7) Turn the TUNE FOLDER PUSH SOUND selection.
To delete a number assigned for the speed
knob (1) to select “Confirm”, and press 7) Press one of the Preset buttons (3) to
dial, follow the instructions below.
the knob (1) to complete the deletion. which the selected number is to be
1) Press the Off Hook button (5).
assigned. If a number is already
NOTE: The Bluetooth® phonebook menu will be
assigned to the selected button, a
When selecting “Go Back”, the previous displayed.
confirmation message will be displayed.
menu will be displayed. 2) Turn the TUNE FOLDER PUSH SOUND
Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Speed Dials”, and
Registration in speed dial knob (1) to select “Confirm”, and press
press the knob (1) to determine the
Follow the instructions below to assign a the knob (1) to complete the assignment.
selection.
number to one of the Preset buttons to use When the assignment is completed, the
3) Press one of the Preset buttons (3) to
as the speed dial. “Setup Phonebook” will be displayed.
which the number to be deleted is
1) Press the Bluetooth® setup button (4). assigned.
NOTE:
The Bluetooth® setup menu will be “No Entry” appears if the number is not
When selecting “Go Back”, the previous
displayed. registered.
menu will be displayed.
2) Turn the TUNE FOLDER PUSH SOUND 4) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Setup Telephone”, One-touch call (Speed dial) knob (1) to select “Delete”, and press
and press the knob (1) to determine the Follow the instructions below to dial the the knob (1) to determine the selection.
selection.
123 7-33
OTHER CONTROLS AND EQUIPMENT MH0-74E
5) Turn the TUNE FOLDER PUSH SOUND NOTE: 1) Press the Bluetooth® setup button (4).
knob (1) to select “Del Speed Dial”, and When selecting “Go Back”, the previous The Bluetooth® setup menu will be
press the knob (1) to determine the menu will be displayed. displayed.
selection. 2) Turn the TUNE FOLDER PUSH SOUND
Reset to the factory defaults
6) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and
Follow the instructions below to reset all the
knob (1) to select “Confirm”, and press press the knob (1) to determine the
settings to the factory defaults.
the knob (1) to complete the deletion. selection.
1) Press the Bluetooth® setup button (4).
3) Turn the TUNE FOLDER PUSH SOUND
NOTE: The Bluetooth® setup menu will be
knob (1) to select “List Phone”, and
When selecting “Go Back”, the previous displayed.
press the knob (1) to determine the
menu will be displayed. 2)Turn the TUNE FOLDER PUSH SOUND
selection.
knob (1) to select “Setup Bluetooth”, and
Display of device data (Device Name) 4) Turn the TUNE FOLDER PUSH SOUND
press the knob (1) to determine the
Follow the instructions below to display the knob (1) to select a phone to be paired
selection.
BD (Bluetooth® Device) address and device with, and press the knob (1) to
3) Turn the TUNE FOLDER PUSH SOUND
name. determine the selection.
knob (1) to select “Initialize”, and press
1) Press the Bluetooth® setup button (4). 5) Turn the TUNE FOLDER PUSH SOUND
the knob (1) to determine the selection.
The Bluetooth® setup menu will be knob (1) to select “Select”, and press the
4) Turn the TUNE FOLDER PUSH SOUND
displayed. knob (1) to determine the selection.
knob (1) to select “All Initialize”, and
2) Turn the TUNE FOLDER PUSH SOUND
press the knob (1) to determine the NOTE:
knob (1) to select “Setup Bluetooth”, and
selection. When selecting “Go Back”, the previous
press the knob (1) to determine the
5) Turn the TUNE FOLDER PUSH SOUND menu will be displayed.
selection.
knob (1) to select “Confirm”, and press The Bluetooth® ready audio device will
3) Turn the TUNE FOLDER PUSH SOUND
the knob (1) to start the reset. be disconnected when the phone is
knob (1) to select “Bluetooth Info”, and
selected.
press the knob (1) to determine the NOTE:
selection. When selecting “Go Back”, the previous List of phones (List Phones)
4) Turn the TUNE FOLDER PUSH SOUND menu will be displayed. Follow the instructions below to display the
knob (1) to select “Device Name” or names of the registered phones in
Selection of phone (Select Phone)
“Device Address”, and press the knob sequence.
Follow the instructions below to select a
(1) to display the device name or the BD 1) Press the Bluetooth® setup button (4).
phone to be paired with from the registered
(Bluetooth® Device) address. The Bluetooth® setup menu will be
phones.
displayed.
7-34 124
MH0-74E OTHER CONTROLS AND EQUIPMENT
2) Turn the TUNE FOLDER PUSH SOUND 5) Press or turn the TUNE FOLDER PUSH 4) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Setup Bluetooth”, and SOUND knob (1) to select “Confirm”. knob (1) to select a phone to be deleted,
press the knob (1) to determine the 6) Turn the TUNE FOLDER PUSH SOUND and press the knob (1) to determine the
selection. knob (1) to select a number for the first selection.
3) Turn the TUNE FOLDER PUSH SOUND digit, and press the knob (1) to 5) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “List Phone”, and determine the selection. Select and knob (1) to select “Delete Phone”, and
press the knob (1) to determine the determine numbers for the second, third press the knob (1) to determine the
selection. and fourth digits in order in the same selection.
4) The names of the registered phones are manner. When not entering up to the 6) Turn the TUNE FOLDER PUSH SOUND
displayed in sequence. eighth digit, enter blanks for the knob (1) to select “Delete?”, and press
successive digits. the knob (1) to determine the selection.
NOTE:
7) Turn the TUNE FOLDER PUSH SOUND 7) Turn the TUNE FOLDER PUSH SOUND
When selecting “Go Back”, the previous
knob (1) to determine the passkey knob (1) to select “Confirm”, and press
menu will be displayed.
setting. the knob (1) to determine the selection.
Passkey setting (Set Passkey)
NOTE: NOTE:
Follow the instructions below to set the
When selecting “Go Back”, the previous When selecting “Go Back”, the previous
security number (Passkey).
menu will be displayed. menu will be displayed.
1) Press the Bluetooth® setup button (4).
The Bluetooth® setup menu will be Deletion of phone information (Delete BT function on/off (BT Power)
displayed. Phone) Follow the instructions below to turn on/off
2) Turn the TUNE FOLDER PUSH SOUND Follow the instructions below to delete the the Bluetooth® function.
knob (1) to select “Setup Bluetooth”, and registered information of the phone. 1) Press the Bluetooth® setup button (4).
press the knob (1) to determine the 1) Press the Bluetooth® setup button (4). The Bluetooth® setup menu will be
selection. The Bluetooth® setup menu will be displayed.
3) Turn the TUNE FOLDER PUSH SOUND displayed. 2) Turn the TUNE FOLDER PUSH SOUND
knob (1) to select “Passkey”, and press 2) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “Setup Bluetooth”, and
the knob (1) to determine the selection. knob (1) to select “Setup Bluetooth”, and press the knob (1) to determine the
4) Turn the TUNE FOLDER PUSH SOUND press the knob (1) to determine the selection.
knob (1) to select “New Passkey”, and selection. 3) Turn the TUNE FOLDER PUSH SOUND
press the knob (1) to determine the 3) Turn the TUNE FOLDER PUSH SOUND knob (1) to select “BT Power”, and press
selection. knob (1) to select “List Phone”, and the knob (1) to determine the selection.
press the knob (1) to determine the
selection.
125 7-35
OTHER CONTROLS AND EQUIPMENT MH0-74E
4) Press the TUNE FOLDER PUSH Steering switch Registration of audio devices
SOUND knob (1) to select “BT Power
On” or “BT Power Off”. To use Bluetooth ®-ready audio devices
with this unit, it required to register the
NOTE: phone in advance.
When the BT function is turned off, the
connection between this unit and the NOTE:
registered phone in use will be (6) To set up a new audio player,
disconnected. disconnect the phone from the unit.
When selecting “Go Back”, the previous Connect the phone after audio player
menu will be displayed. setup is completed if necessary.
When failed to establish the connection
Bluetooth® audio (if equipped) within 120 seconds, the connecting
operation will be canceled. Please try
again or refer to the audio player manual
76MH0A141
for assistance with the pairing process.
Display 1) Press the Bluetooth® setup button (6).
(3) The Bluetooth® setup menu will be
(4) displayed.
(1)
2) Turn the TUNE FOLDER PUSH SOUND
(5)
(2)
knob (2) to select “Setup Bluetooth”, and
press the knob (2) to determine the
selection.
MH0-D2-BTA-001
3) Turn the TUNE FOLDER PUSH SOUND
1) MEDIA button knob (2) to select “Pairing”, and press
76MH0A103
2) TUNE FOLDER PUSH SOUND knob the knob (2) to determine the selection.
3) Up button 4) Select “CAR AUDIO” from the Bluetooth ®
NOTE: 4) Down button menu of the audio player and establish
Applicable for Bluetooth® audio version 5) DISP button the pairing.
2.1 and above. 6) Bluetooth® setup button Refer to the manual of the audio player
A) Track number in use for further information.
B) Play time 5) Enter the Passkey displayed on the unit
to the audio player (For phones with
7-36 126
MH0-74E OTHER CONTROLS AND EQUIPMENT
Bluetooth version 2.1 or above passkey Press the Down button (4) twice to listen NOTE:
input is not required). to the previous track. If text data contains more than 12 charac-
When the Down button (4) is pressed ters, the “>” mark will appear at the right
NOTE:
once, the track currently being played end. Holding down the DISP button (5) for
When selecting “Go Back”, the previous
will start from the beginning again. 1 second or longer can display the next
menu will be displayed.
page.
When additionally registering audio Fast forwarding/Rewinding a track
devices, operate the same step from 1). Hold down the Up button (3) to fast Selection of audio device (Select Audio)
forward the track. Follow the instructions below to select an
Selecting the Bluetooth® audio mode audio device to be paired with from the
Hold down the Down button (4) to fast
Press the MEDIA button (1). registered audio devices.
rewind the track.
Each time the button is pressed, the mode 1) Press the Bluetooth® setup button (6).
will change as follows: NOTE: The Bluetooth® setup menu will be
Some functions may not be available displayed.
depending on Bluetooth® audio. 2) Turn the TUNE FOLDER PUSH SOUND
Display change knob (2) to select “Setup Bluetooth”, and
Press the DISP button (5). press the knob (2) to determine the
Each time the button is pressed, display will selection.
change as follows: 3) Turn the TUNE FOLDER PUSH SOUND
knob (2) to select “List Audio”, and press
the knob (2) to determine the selection.
4) Turn the TUNE FOLDER PUSH SOUND
knob (2) to select an audio device to be
used, and press the knob (2) to
determine the selection.
MH0-05-011 5) Turn the TUNE FOLDER PUSH SOUND
Selecting a group (only for supported knob (2) to select “Select”, and press the
models) knob (2) to determine the selection.
Turn the TUNE FOLDER PUSH SOUND 6) Turn the TUNE FOLDER PUSH SOUND
knob (2) to select a group. knob (2) to select “Confirm”, and press
the knob (2) to complete the pairing.
Selecting a track
Press the Up button (3) to listen to the
MH0-05-016
next track.
127 7-37
OTHER CONTROLS AND EQUIPMENT MH0-74E
NOTE: 2) Turn the TUNE FOLDER PUSH SOUND 1) Press the Bluetooth® setup button (6).
When selecting “Go Back”, the previous knob (2) to select “Setup Bluetooth”, and The Bluetooth® setup menu will be
menu will be displayed. press the knob (2) to determine the displayed.
The phone will be disconnected when selection. 2) Turn the TUNE FOLDER PUSH SOUND
the Bluetooth® ready audio device is 3) Turn the TUNE FOLDER PUSH SOUND knob (2) to select “Setup Bluetooth”, and
selected. knob (2) to select “Passkey”, and press press the knob (2) to determine the
the knob (2) to determine the selection. selection.
List of audio devices (List Audio)
4) Turn the TUNE FOLDER PUSH SOUND 3) Turn the TUNE FOLDER PUSH SOUND
Follow the instructions below to display the
knob (2) to select “New Passkey”, and knob (2) to select “List Audio”, and press
names of the registered audio devices in
press the knob (2) to determine the the knob (2) to determine the selection.
sequence.
selection. 4) Turn the TUNE FOLDER PUSH SOUND
1) Press the Bluetooth® setup button (6).
5) Press or turn the TUNE FOLDER PUSH knob (2) to select an audio device to be
The Bluetooth® setup menu will be
SOUND knob (2) to select “Confirm”. deleted, and press the knob (2) to
displayed.
6) Turn the TUNE FOLDER PUSH SOUND determine the selection.
2) Turn the TUNE FOLDER PUSH SOUND
knob (2) to select a number for the first 5) Turn the TUNE FOLDER PUSH SOUND
knob (2) to select “Setup Bluetooth”, and
digit, and press the knob (2) to knob (2) to select “Delete”, and press
press the knob (2) to determine the
determine the selection. Select and the knob (2) to determine the selection.
selection.
determine numbers for the second, third 6) Turn the TUNE FOLDER PUSH SOUND
3) Turn the TUNE FOLDER PUSH SOUND
and fourth digits in order in the same knob (2) to select “Delete?”, and press
knob (2) to select “List Audio”, and press
manner. When not entering up to the the knob (2) to determine the selection.
the knob (2) to determine the selection.
eighth digit, enter blanks for the 7) Turn the TUNE FOLDER PUSH SOUND
The names of registered audio devices
successive digits. knob (2) to select “Confirm”, and press
will be displayed in sequence.
7) Turn the TUNE FOLDER PUSH SOUND the knob (2) to complete the deletion.
NOTE: knob (2) to determine the passkey
NOTE:
When selecting “Go Back”, the previous setting.
When selecting “Go Back”, the previous
menu will be displayed.
NOTE: menu will be displayed.
Passkey setting (Set Passkey) When selecting “Go Back”, the previous
Follow the instructions below to set the menu will be displayed. Disclaimer for Bluetooth® function
security number (Passkey). • Depending on the mobile phone models,
Deletion of audio device information some phones may not be compatible fully
1) Press the Bluetooth® setup button (6). (Delete Audio)
The Bluetooth® setup menu will be or partially (some function may be
Follow the instructions below to delete the restricted).
displayed. registered information of audio device.
7-38 128
MH0-74E OTHER CONTROLS AND EQUIPMENT
• Connectivity or voice quality may get To decrease the volume, hold down “-” To scan a higher frequency radio station,
affected depending on circumstances. of the VOL switch (1). The volume will press “^” of the switch (4) for 1 second
• After the ignition switch is turned to the keep on being decreased until the switch or longer.
“ON” position, the audio system takes few is released. To scan a lower frequency radio station,
seconds to detect and connect to the To mute the sound, press the switch (2). press “v” of the switch (4) for 1 second
Bluetooth® device (if already paired). or longer.
Selecting the mode
• Make sure that you are aware of all Selecting the track (CD, USB (iPod ®),
Press the switch (3).
applicable local laws and accordingly use Bluetooth® audio mode)
Bluetooth device. Each time the button is pressed, the mode
will change as follows: To skip to the next track, press “^” of
the switch (4) only for a moment.
Remote Audio Controls (if equipped) To skip to the previous track, press “v”
Controlling of basic functions of the audio of the switch (4) twice only for a
system is available using the switches on moment.
the steering wheel. When the switch (4) is pushed down
once only for a moment, the track
currently being played will start from the
beginning again.
(2) (3)
Fast forwarding/Rewinding a track
To fast forward, press “^” of the switch
(4) for 1 second or longer.
To fast rewind, press “v” of the switch (4)
MH0-05-017 for 1 second or longer.
(1) (4) It is possible to turn on the audio system
by pressing the switch (3).
Selecting the radio station (FM1, FM2,
68LM553
AM mode)
Adjusting the volume To select the next preset station, press
To increase the volume, hold down “+” “^” of the switch (4) only for a moment.
of the VOL switch (1). The volume will To select the previous preset station,
keep on being increased until the switch press “v” of the switch (4) only for a
is released. moment.
129 7-39
OTHER CONTROLS AND EQUIPMENT MH0-74E
Anti-Theft Feature Setting the Anti-Theft Function 4) Enter a 4-digit number to be registered
1) Press the VOL PUSH POWER knob (1) as PIN using the buttons numbered [1]
to power off. - [4] of the Preset buttons (2).
2) Hold down the buttons numbered [1] and 5) Hold down the TUNE FOLDER PUSH
[6] of the Preset buttons (2) and press SOUND knob (4) for 1 second or longer
the VOL PUSH POWER knob (1). to delete the registered PIN. The indi-
(3) “SECURITY” will be displayed. cation “——” will be displayed and the
3) Press the Up button (3) and the button anti-theft function will be canceled.
numbered [1] of the Preset buttons (2)
NOTE:
simultaneously.
(4) (1)
To change your PIN, first delete your cur-
4) Enter a 4-digit number to be registered
rent PIN, then set a new one.
as PIN using the buttons numbered [1]
(2) - [4] of the Preset buttons (2). Confirming the Personal Identification
5) Hold down the TUNE FOLDER PUSH Number (PIN)
76MH0A105 SOUND knob (4) for 1 second or longer When the main power source is discon-
1) VOL PUSH POWER knob to set the anti-theft function. nected such as when the battery is
2) Preset buttons ([1] to [6]) replaced, etc, it is required to enter the PIN
NOTE:
3) Up button to make the unit operable again.
Take a note of the registered PIN and keep
4) TUNE FOLDER PUSH SOUND knob 1) Set the ignition switch to the “ACC”
it for the future use.
position.
The anti-theft function is intended to dis- Canceling the anti-theft feature “SECURITY” will be displayed.
courage thefts, such as that the audio sys- To cancel the anti-theft function, delete the 2) Press the Up button (3) and the button
tem becomes inoperable when it is installed registered PIN. numbered [1] of the Preset buttons (2)
on other vehicles. 1) Press the VOL PUSH POWER knob (1) simultaneously.
This function works by entering a Personal to power off. 3) Enter a 4-digit number to be registered
Identification Number (PIN). 2) Hold down the buttons numbered [1] and as PIN using the buttons numbered [1]
When the unit is disconnected from its [6] of the Preset buttons (2) and press - [4] of the Preset buttons (2).
power source, such as when the audio the VOL PUSH POWER knob (1). 4) Hold down TUNE FOLDER PUSH
system is removed or the battery is discon- “PIN ENTRY” will be displayed. SOUND knob (4) for 1 second or longer.
nected, the unit will become inoperable until 3) Press the Up button (3) and the button When the PIN same as registered is
the PIN is reentered. numbered [1] of the Preset buttons (2) entered, the power of the audio system
simultaneously. will be turned off automatically and it will
become operable again.
7-40 130
MH0-74E OTHER CONTROLS AND EQUIPMENT
NOTE: Battery replacement timing If battery leakage has occurred, wipe the
If an incorrect PIN is entered, “ERROR” and When battery power is depleted, the but- container first then install a new battery. If
the total number of incorrect entry attempts ton may not be operable. If the remote the battery solution contacts the skin, wash
will be displayed. controller does not operate, replace the off with water completely.
If an incorrect PIN is entered 10 times, battery and check the operation.
Caution on Remote Controller
“HELP” will be displayed and the audio
Caution on battery Do not leave the remote controller in an
system will become inoperable.
Be sure to follow the instructions to area exposed to direct sunlight, such as
Battery Installation prevent battery leakage, over-heating, on the dashboard or steering wheel. The
ignition or explosion. remote controller may deform because of
Install a lithium battery (CR2025) with the the heat, (Be especially careful of the
poles facing the correct direction. WARNING dashboard exposed to direct sunlight in
the summer, as it will become extremely
Do not expose the battery to flame.
hot).
Do not short circuit, disassemble, or
When the vehicle is parked in an area
heat the battery.
exposed to direct sunlight, Ensure the
Do not charge the battery.
remote controller is placed in an area
Use the specified type battery.
not exposed to direct sunlight. For
Keep the button-shaped battery
example: Glove box.Under direct sun-
away from children to prevent acci-
light, signal reception from the remote
dental swallowing.
controller weakens. If this happens, hold
If the battery is swallowed, contact a
the remote controller close to the signal
doctor immediately.
receptor on the front panel.
CAUTION
Install the battery with the poles
facing the correct direction.
When not in use for a long period
of time, or if the battery is dead,
remove the battery from the remote
controller.
MH0-05-017A
131 7-41
OTHER CONTROLS AND EQUIPMENT MH0-74E
Remote Controller
common operations
MH0-05-018
7-42 132
MH0-74E OTHER CONTROLS AND EQUIPMENT
Radio operations
NOTE:
When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will be
stored at the remaining preset buttons.
MH0-05-019
133 7-43
OTHER CONTROLS AND EQUIPMENT MH0-74E
CD operations
MH0-05-020
7-44 134
MH0-74E OTHER CONTROLS AND EQUIPMENT
MH0-05-021
135 7-45
OTHER CONTROLS AND EQUIPMENT MH0-74E
USB operations
MH0-05-022
7-46 136
MH0-74E OTHER CONTROLS AND EQUIPMENT
iPod operations
MH0-05-023
137 7-47
OTHER CONTROLS AND EQUIPMENT MH0-74E
Troubleshooting
When encountered a problem, check and follow the instructions as described below.
If the described suggestions do not solve the problem, it is recommended to take the unit to your authorized MARUTI SUZUKI deal er.
Radio
Much noise It may not be exactly tuned in to the Tune it in exactly to the station.
station.
Unable to receive by auto tuning There may be no station emitting signals Pick up a station by manual tuning.
powerful enough.
CD
Sound skips or noise produced The disc is dirty. Wipe the disc with a soft cloth.
The disc has a major scratch or is warped. Replace the disc with the one with no
scratch and also not warped.
7-48 138
MH0-74E OTHER CONTROLS AND EQUIPMENT
USB
Playback does not start when the USB There is no supported format file to play Check the file format.
device is connected. on this unit.
The current consumption of the USB Use an USB device with a current
device exceeds 1.0 A. consumption lower than 1.0 A.
Bluetooth®
The distance between this unit and the
Bluetooth® ready device is too far, or a Change the location of the Bluetooth ®
metallic object may be located between ready device.
the Bluetooth® ready device and this unit.
Pairing failed Refer to the manual of the Bluetooth ®
The Bluetooth® function of the Bluetooth ® ready device. (Some devices have the
ready device is off. power saving function that automatically
activates after a certain time.)
Unable to receive a call. Your current location may be out of ser- Drive your vehicle to the service area of
vice area. the phone.
The voice quality of hands-free is low Another wireless device may be located Switch off the wireless device or keep it
(Distortion, noise etc.). near the unit. away from the unit.
139 7-49
OTHER CONTROLS AND EQUIPMENT MH0-74E
USB/iPod ®
ERROR 1 The USB device is disconnected. Check the connection of the USB device.
ERROR 2 Impossible to communicate correctly with Unplug the USB device and plug it again.
the USB device. Check the USB device.
ERROR 3 Inoperable due to an unidentified cause. Unplug the USB device and plug it again.
When ERROR 3 does not disappear, contact your dealer.
ERROR 4 The current consumption of the USB Check the USB device.
device exceeds 1.0 A.
7-50 140
MH0-74E OTHER CONTROLS AND EQUIPMENT
141 7-51
VEHICLE LOADING AND TOWING MH0-74E
142
MH0-74E VEHICLE LOADING AND TOWING
143 8-1
VEHICLE LOADING AND TOWING MH0-74E
8-2 144
MH0-74E INSPECTION AND MAINTENANCE
145
INSPECTION AND MAINTENANCE MH0-74E
WARNING WARNING
The wires are wrapped with yellow Be careful not to cause accidental
tape or yellow tubing, and the short circuits between the positive
couplers are yellow for easy and negative battery terminals.
identification. Keep used oil, coolant, and other
Do not leave the engine running in fluids away from children and pets.
garages or other confined areas. Dispose of used fluids properly;
When the engine is running, keep never pour them on the ground, into
hands, clothing, tools, and other sewers, etc.
objects away from the fan and drive
belt. Even though the fan may not
60A187S be moving, it can automatically turn Maintenance Schedule
on without warning. The following table shows the times when you
WARNING When it is necessary to do service should perform regular maintenance on your
You should take extreme care when work with the engine running, make vehicle. This table shows in kilometers and
working on your vehicle to prevent sure that the parking brake is set m o n t h s w h e n yo u s h o u l d p e r fo r m
accidental injury. Here are a few fully and the transaxle is in Neutral. inspections, adjustments, lubrication and
precautions that you should be Do not touch ignition wires or other other services.
especially careful to observe: ignition system parts when starting
To prevent damage or unintended the engine or when the engine is
activation of the air bag system be running, or you could receive an
sure the battery is disconnected and electric shock.
the ignition switch has been in the Be careful not to touch a hot
“LOCK” position for at least 90 engine, exhaust manifold and pipes,
seconds before performing any muffler, radiator and water hoses.
electrical service work on your Do not allow smoking, sparks, or
MARUTI SUZUKI. Do not touch air flames around fuel or the battery.
bag system components or wires. Flammable fumes are present.
Do not get under your vehicle if it
is supported only with the portable
jack provided in your vehicle.
9-1 146
MH0-74E INSPECTION AND MAINTENANCE
WARNING
MARUTI SUZUKI recommends that
maintenance on your Maruti Suzuki
vehicle should be performed by
MARUTI SUZUKI authorised workshop/
Service station.
NOTICE
Whenever it becomes necessary to
replace parts on your vehicle, it is
recommended that you use MARUTI
genuine replacement parts or their
equivalent.
147 9-2
INSPECTION AND MAINTENANCE MH0-74E
9-3 148
MH0-74E INSPECTION AND MAINTENANCE
6. Master cylinder sub assembly, wheel cylinder boot kit & caliper seat set I I I I I R I I I R
149 9-4
INSPECTION AND MAINTENANCE MH0-74E
9-5 150
MH0-74E INSPECTION AND MAINTENANCE
151 9-6
INSPECTION AND MAINTENANCE MH0-74E
Drive Belt Engine Oil and Filter It is important to keep the engine oil at the
correct level for proper lubrication of your
WARNING Specified Oil vehicle’s engine. Check the oil level with the
When the engine is running, keep vehicle on a level surface. The oil level
hands, hair, clothing, tools, etc. away indication may be inaccurate if the vehicle
from the moving fan and drive belts. is on a slope. The oil level should be
Make sure the drive belt tension is correct. checked either before starting the engine or
If the belt is too loose, insufficient battery at least 5 minutes after stopping the engine.
charging, engine overheating, poor power 68LM20702 The handle of the engine oil dipstick is
steering, poor air conditioning, or excessive colored yellow for easy identification.
belt wear can result. When you press the (1) Preferred
belt with your thumb midway between the Be sure that the engine oil you use comes EXAMPLE
pulleys, there should be a deflection under the quality classification of SL. Select
according to the following chart. the appropriate oil viscosity according to the
The belts should also be examined to above chart.
ensure that they are not damaged. SAE 0W-20 (1) is the best choice for good
If you need to replace or adjust the belt fuel economy, and good starting in cold
have it done by your MARUTI SUZUKI weather.
dealer.
K10B Oil Level Check
DEF: 4.0 – 4.5 mm EXAMPLE
(0.16 – 0.18 in.)
52D084
(1)
68KH068
81A147
Tightening torque for drain plug (1):
Remove the oil filler cap and pour oil slowly 35 Nm (3.6 kg-m, 25.8 lb-ft)
through the filler hole to bring the oil level
to the upper limit on the dipstick. Be careful
68KH067 WARNING
not to overfill. Too much oil is almost as 1) Remove the oil filler cap. New and used oil can be hazardous.
bad as too little oil. After refilling, start the 2) Place a drain pan under the drain plug. Children and pets may be harmed by
engine and allow it to idle for about a 3) Using a wrench, remove the drain plug swallowing new or used oil. Keep new
minute. Stop the engine, wait about 5 and drain out the engine oil. and used oil and used oil filters away
minutes and check the oil level again. from children and pets.
CAUTION Repeated, prolonged contact with used
The engine oil temperature may be engine oil may cause skin cancer.
high enough to burn your fingers Brief contact with used oil may irritate
when the drain plug is loosened. Wait skin.
until the drain plug is cool enough to To minimize your exposure to used
touch with your bare hands. oil, wear a long-sleeve shirt and
moisture-proof gloves (such as dish-
washing gloves) when changing oil. If
oil contacts your skin, wash thoroug-
hly with soap and water.
153 9-8
INSPECTION AND MAINTENANCE MH0-74E
9-9 154
MH0-74E INSPECTION AND MAINTENANCE
4) Stop the engine and wait about 5 Gives proper protection against freezing Coolant Level Check
minutes. Check the oil level again and and boiling.
Check the coolant level at the reservoir
add oil if necessary. Check for leaks Gives proper protection against corrosion tank, not at the radiator. With the engine
again. and rust. cool, the coolant level should be between
Failure to use the proper coolant can dam- the “FULL” and “LOW” marks.
NOTICE age your cooling system. Your authorized
MARUTI SUZUKI dealer can help you select Adding Coolant
When replacing the oil filter, it is
recommended that you use a Maruti the proper coolant.
EXAMPLE
genuine replacement filter. If you use
an aftermarket filter, make sure it is of
NOTICE
equivalent quality and follow the To avoid damaging your cooling
manufacturer’s instructions. system:
Oil leaks from around the oil filter or Always use a high quality ethylene
drain plug indicate incorrect glycol base non-silicate type coolant
installation or gasket damage. If you diluted with distilled water at the
find any leaks or are not sure that the correct mixture concentration.
filter has been properly tightened, Make sure that the proper mix is 30/
have the vehicle inspected by your 70 coolant to distilled water and in
MARUTI SUZUKI dealer. no case higher than 70/30.
Concentrations greater than 70/30 76MH0A107
155 9-10
INSPECTION AND MAINTENANCE MH0-74E
Coolant Replacement
Since special procedures are required, we
recommend you take your vehicle to your
MARUTI SUZUKI dealer for coolant
replacement.
9-11 156
MH0-74E INSPECTION AND MAINTENANCE
60G160S
68KH072
78K179
For nickel spark plugs (traditional type):
You should inspect spark plugs periodically
for carbon deposits. When carbon
accumulates on a spark plug, a strong
157 9-12
INSPECTION AND MAINTENANCE MH0-74E
NOTICE
When tightening the plug, apply the
following sealing compound or
equivalent to the plug threads to
prevent oil leakage.
Manual transaxle sealant: 54G274 76MH0A110
SUZUKI Bond No. “1216E” or “1217G” Clutch pedal play “d”: Check the brake fluid level by looking at the
10 - 15 mm (0.4 - 0.6 in.) reservoir in the engine compartment. Check
Gear Oil Change Measure the clutch pedal play by moving that the fluid level is between the “MAX”
Since special procedures, materials and the clutch pedal with your hand and and “MIN” lines. If the brake fluid level is
tools are required, it is recommended that measuring the distance it moves until you near the “MIN” line, fill it up to the “MAX”
you trust this job to your authorized feel slight resistance. The play in the clutch line with Maruti Genuine brake fluid.
MARUTI SUZUKI dealer. pedal should be between the specified
values. If the play is more or less than the
above, or clutch dragging is felt with the
pedal fully depressed, have the clutch
inspected by your MARUTI SUZUKI dealer.
159 9-14
INSPECTION AND MAINTENANCE MH0-74E
WARNING WARNING
Failure to follow the guidelines below Brake fluid is harmful or fatal if swal-
can result in personal injury or lowed, and harmful if it comes in con-
serious damage to the brake system. tact with skin or eyes. If swallowed,
If the brake fluid in the reservoir do not induce vomiting. Immediately
drops below a certain level, the contact a poison control center or a
brake warning light on the physician. If brake fluid gets in eyes,
instrument panel will come on (the flush eyes with water and seek medi-
engine must be running with the cal attention. Wash thoroughly after
parking brake fully disengaged). handling. Solution can be poisonous
Should the light come on, immedia- to animals. Keep out of the reach of
tely ask your MARUTI SUZUKI children and animals. 54G108
dealer to inspect the brake system.
Pedal to floor carpet minimum dis-
A rapid fluid loss indicates a leak in NOTE: tance “a”:
the brake system which should be With disc brakes, the fluid level can be 66 mm (2.6 in.)
inspected by your MARUTI SUZUKI expected to gradually fall as the brake pads
dealer immediately. wear. With the engine running, measure the
Do not use any fluid other than distance between the brake pedal and floor
Maruti Genuine brake fluid. Do not Brake Pedal carpet when the pedal is depressed with
use reclaimed fluid or fluid that has Check if the brake pedal stops at the approximately 30 kg (66 lbs) of force. The
been stored in old or open contain- regular height without “spongy” feeling when minimum distance required is as specified.
ers. It is essential that foreign you depress it. If not, have the brake Since your vehicle’s brake system is self-
partic-les and other liquids are kept system inspected by your MARUTI SUZUKI adjusting, there is no need for pedal
out of the brake fluid reservoir. dealer. If you doubt the brake pedal for the adjustment.
regular height, check it as follows: If the pedal to floor carpet distance as
measured above is less than the minimum
CAUTION distance required, have your vehicle
Brake fluid can harm your eyes and inspected by your MARUTI SUZUKI dealer.
damage painted surfaces. Use caution
when refilling the reservoir. NOTE:
When measuring the distance between the
brake pedal and floor wall, be sure not to
9-15 160
MH0-74E INSPECTION AND MAINTENANCE
include the floor mat or rubber on the floor Parking Brake Steering
wall in your measurement.
EXAMPLE EXAMPLE
“c”
EXAMPLE
54G109 68LM708
60G104A
Ratchet tooth specification “b”: Steering wheel play “c”:
WARNING 4th – 9th 0 – 30 mm (0.0 – 1.2 in.)
Lever pull force (1):
If you experience any of the following Check the play of the steering wheel by
200 N (20 kg, 44 lbs)
problems with your vehicle’s brake gently turning it from left to right and
system, have the vehicle inspected Check the parking brake for proper adjust- measuring the distance that it moves before
immediately by your MARUTI SUZUKI ment by counting the number of clicks made you feel slight resistance. The play should
dealer. by the ratchet teeth as you slowly pull up be between the specified values.
Poor braking performance on the parking brake lever to the point of
Check that the steering wheel turns easily
Uneven braking (brakes not working full engagement. The parking brake lever
and smoothly without rattling by turning it
uniformly on all wheels.) should stop between the specified ratchet
all the way to the right and to the left while
Excessive pedal travel teeth and the rear wheels should be
driving very slowly in an open area. If the
Brake dragging securely locked. If the parking brake is not
amount of free play is outside the
Excessive noise properly adjusted or the brakes drag after
specification or you find anything else to be
Pedal pulsation (pedal pulsates the lever has been fully released, have the
wrong, an inspection must be performed by
when depressed) (Normal in case of parking brake inspected and/or adjusted by
your MARUTI SUZUKI dealer.
ABS equipped vehicle). your MARUTI SUZUKI dealer.
161 9-16
INSPECTION AND MAINTENANCE MH0-74E
9-17 162
MH0-74E INSPECTION AND MAINTENANCE
Wheel Alignment
NOTICE NOTICE In case of abnormal tyre wear or pulling
Hitting curbs and running over rocks Replacing the original tires with tires towards one side, have the wheel aligned
can damage tires and affect wheel of a different size may result in false at Maruti Suzuki Authorized Workshop.
alignment. Be sure to have tires and speedometer or odometer readings.
wheel alignment checked periodically Battery
by your MARUTI SUZUKI dealer. Tire Rotation
4) Check for loose wheel nuts.
WARNING
5) Check that there are no nails, stones or Batteries produce flammable
other objects sticking into the tires. hydrogen gas. Keep flames and
sparks away from the battery or an
WARNING explosion may occur. Never smoke
Your MARUTI SUZUKI is equipped when working in the vicinity of the
with tires which are all the same type battery.
and size. This is important to ensure When checking or servicing the
proper steering and handling of the battery, disconnect the negative
vehicle. Never mix tires of different cable. Be careful not to cause a
size or type on the four wheels of short circuit by allowing metal
your vehicle. The size and type of tires objects to contact the battery posts
used should be only those approved 80JK040A and the vehicle at the same time.
by MARUTI SUZUKI as standard or To avoid harm to yourself or
To avoid uneven wear of your tires and to
optional equipment for your vehicle. damage to your vehicle or battery,
prolong their life, rotate the tires as illustra-
Replacing the wheels and tires follow the jump starting instructions
ted. Tires should be rotated as mentioned
equipped on your vehicle with in the “EMERGENCY SERVICE”
in periodic maintenance schedule. After
certain combinations of aftermarket section of this manual if it is
rotation, adjust front and rear tire pressures
wheels and tires can significantly necessary to jump start your
to the specification listed on your vehicle’s
change the steering and handling vehicle.
Tire Information Label.
characteristics of your vehicle.
Therefore, use only those wheel and Wheel Balancing
tire combinations approved by If the vehicle vibrates abnormally on smooth
MARUTI SUZUKI as standard or road, have the wheel balanced at Maruti
optional equipment for your vehicle. Suzuki Authorized Workshop.
163 9-18
INSPECTION AND MAINTENANCE MH0-74E
Fuses in the Engine Compartment MAIN FUSE/PRIMARY FUSE The main fuse, primary fuses and some of
the individual fuses are located in the
(1) 80A FL1
engine compartment. If the main fuse blows,
EXAMPLE (2) 50A FL5 no electrical component will function. If a
(3) 50A FL4 primary fuse blows, no electrical component
(4) – Front fog light relay in the corresponding load group will
(2) (5) – Blank function. When replacing the main fuse, a
primary fuse or an individual fuse, use a
(3) (6) – Blank
MARUTI genuine part replacement.
(27) (1) (7) – Air compressor relay To remove a fuse, use the fuse puller
(28) (8) – Back up relay provided in the fuse box. The amperage of
(9) – F/P relay each fuse is shown in the back of the fuse
(10) 40A ABS motor box cover.
(11) 40A T/M pump
EXAMPLE
(12) 40A Power steering
68KH076 OK
(13) 20A Front fog light
EXAMPLE (14) 7.5A T/M 2
(15) 30A Ignition switch BLOWN
(4) (5) (6) (7) (8) (9) (10) (16) 10A Air compressor 60G111
(12)
(18) 10A T/M WARNING
(19) 15A Headlight (Right)
If the main fuse or a primary fuse
(20) 25A ABS control module blows, be sure to have your vehicle
(13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (21) 15A Headlight (Left) inspected by an authorized MARUTI
(24) (25) (26) (22) 30A Starting motor SUZUKI dealer. Always use a MARUTI
(23) 30A Radiator fan genuine part replacement. Never use
(24) – FI main relay a substitute such as a wire even for
68KH077
(25) – Starting motor relay a temporary repair, or extensive
(26) – Radiator fan relay electrical damage and a fire can result.
(27) 80A FL3
(28) 80A FL2
165 9-20
INSPECTION AND MAINTENANCE MH0-74E
Side Turn Signal Light (if equipped) 2) Turn the bulb holder (2) clockwise and Front Turn Signal Light (1)
pull it out from the light housing. Front Position Light (2)
EXAMPLE
(2)
(3)
(4)
(1)
(5)
(1)
76MH0A006
(1)
76MH0A117
light housing, turn the holder counter- Front Fog Light (if equipped)
clockwise and pull it out.
1) Start the engine. Turn the steering wheel
EXAMPLE to the opposite side of the replacing fog
light to replace the bulb easily. Then turn
off the engine.
(1)
(2)
EXAMPLE
(3)
(4) 76MH0A120
(1)
3) Open the end of the cover inside the
61MM0B078 fender.
(3) Removal
(4) Install EXAMPLE EXAMPLE
80JM071
169 9-24
INSPECTION AND MAINTENANCE MH0-74E
EXAMPLE
(2)
(1)
76MH0A124
(3) / (4) / (5) NOTE:
76MH0A121 (6) When reinstalling the light housing, make
1) Remove the bolts (1) and pull the light (7) sure the clips are properly attached.
housing (2) straight.
License Plate Light
76MH0A123
EXAMPLE
(3) (6) Removal
(7) Install
(4)
3) To remove the bulb of the tail/brake light
(3), the turn signal light (4) or the
reversing light (5) from bulb holder, push
(5) in the the bulb and turn it counterclock-
wise. To install a new bulb, push it in
and turn it clockwise.
(1)
76MH0A122 76MH0A125
1) Turn the cover (1) counterclockwise to
remove it.
9-25 170
MH0-74E INSPECTION AND MAINTENANCE
(3)
(2) (4)
(5)
(2)
(1)
68KS063
60G115 54G129
76MH0A139
9-27 172
MH0-74E INSPECTION AND MAINTENANCE
Removal
EXAMPLE EXAMPLE
EXAMPLE 54G135
60A260
(1) Retainer
Installation
4) If the new blade is provided without the
two metal retainers, move them from the
old blade to the new one.
(3) EXAMPLE
54G130
173 9-28
INSPECTION AND MAINTENANCE MH0-74E
(A)
(B)
(3)
60MH072 65D151
(A) Up NOTE:
(B) Down Do not flex the wiper blade frame end more
than necessary. If you do, it can break off.
NOTE:
When you install the metal retainers (3),
make sure the direction of metal retainers
as shown in the above illustrations.
5) Install the new blade in the reverse order
of removal, with the locked end
positioned toward the wiper arm.
Make sure the blade is properly retained
by all the hooks. Lock the blade end into
80G146
place.
6) Reinstall wiper frame to arm, making 1) Hold the wiper arm away from the
sure that the lock lever is snapped window.
securely into the arm. 2) Remove the wiper frame from the arm
54G135
as shown.
3) Slide the blade out as shown. (1) Retainer
9-29 174
MH0-74E INSPECTION AND MAINTENANCE
175 9-30
EMERGENCY SERVICE MH0-74E
EMERGENCY SERVICE
Tire Changing Tool............................................................................................................ 10-1
Jacking Instructions ......................................................................................................... 10-1
Changing Wheels .............................................................................................................. 10-3
Jump Starting Instructions.............................................................................................. 10-4
Towing ................................................................................................................................. 10-5
If the Starter Does Not Operate..................................................................................... 10-6
If the Engine is Flooded ................................................................................................. 10-6
If the Engine Overheats .................................................................................................. 10-6
176
MH0-74E EMERGENCY SERVICE
MH0-07-001
(1) MH0-07-014
7) Continue to raise the jack slowly and Front jacking point for garage jack (1)
EXAMPLE
smoothly until the tire clears the ground.
Do not raise the vehicle more than EXAMPLE
necessary.
WARNING
Use the jack only to change wheels
on level, hard ground.
Never jack up the vehicle on an
inclined surface.
Never raise the vehicle with the jack
in a location other than the specified
MH0-07-014
jacking point (shown in the illustra-
tion) near the wheel to be changed.
Make sure that the jack is raised at
EXAMPLE least 51 mm (2 inches) before it
contacts the flange. Use of the jack
when it is within 51 mm (2 inches)
of being fully collapsed may result
in failure of the jack.
Never get under the vehicle when it
is supported by the jack.
Never run the engine when the
(1)
vehicle is supported by the jack and
never allow passengers to remain in
the vehicle.
NOTE:
For more details, please contact an
authorized MARUTI SUZUKI dealer.
Changing Wheels
(2)
To change a wheel, use the following MH0-07-014
procedure:
Tightening torque for wheel nut
MH0-07-014 1) Clear all passengers and luggage from
85 Nm (8.7 kg-m, 62.7 lb-ft)
Application point for jack stand (3) the vehicle.
or two-column lift 2) Remove the jack, tools and spare wheel 8) Lower the jack and fully tighten the nuts
from the vehicle. in a crisscross fashion with a wrench as
EXAMPLE 3) Loosen, but do not remove the wheel shown in the illustration.
nuts.
4) Jack up the vehicle. WARNING
5) Remove the wheel nuts and wheel. Use genuine wheel nuts and tighten
6) Before installing the new wheel, clean them to the specified torque as soon
any mud or dirt off from the surface of as possible after changing wheels.
the wheel and hub with a clean cloth. Incorrect wheel nuts or improperly
Clean the hub carefully; it may be hot tightened wheel nuts may come loose
from driving. or fall off, which can result in an
(3) (3) 7) Install the new wheel and replace the accident. If you do not have a torque
wheel nuts with their cone shaped end wrench, have the wheel nut torque
facing the wheel. Tighten each nut checked by an authorized MARUTI
MH0-07-014
snugly by hand until the wheel is SUZUKI dealer.
securely seated on the hub.
179 10-3
EMERGENCY SERVICE MH0-74E
MH0-07-014
183 10-7
APPEARANCE CARE MH0-74E
APPEARANCE CARE
Corrosion Prevention 4) High temperatures will cause an Remove foreign material deposits
It is important to take good care of your accelerated rate of corrosion to parts of Foreign material such as salts, chemicals,
vehicle to protect it from corrosion. Listed the vehicle which are not well ventilated road oil or tar, tree sap, bird droppings and
below are instructions for how to maintain to permit quick drying. industrial fall-out may damage the finish of
your vehicle to prevent corrosion. Please your vehicle if it is left on painted surfaces.
read and follow these instructions carefully. This information illustrates the necessity of Remove these types of deposits as quickly
keeping your vehicle (par ticularly the as possible. If these deposits are difficult to
Important Information About underbody) as clean and dry as possible. wash off, an additional cleaner may be
Corrosion It is equally important to repair any damage required. Be sure that any cleaner you use
to the paint or protective coatings as soon is not harmful to painted surfaces and is
Common cause of corrosion
as possible. specifically intended for your purposes.
1) Accumulation of road salt, dirt, moisture,
Follow the manufacturer’s directions when
or chemicals in hard-to-reach areas of How to Help Prevent Corrosion using these special cleaners.
the vehicle underbody or frame.
2) Chipping, scratches and any damage to Wash your vehicle frequently Repair finish damage
treated or painted metal surfaces resulting The best way to preserve the finish on your Carefully examine your vehicle for damage
from minor accidents or abrasion by vehicle and to help avoid corrosion is to to the painted surfaces. Should you find any
stones and gravel. keep it clean with frequent washing. chips or scratches in the paint, touch them
Wash your vehicle at least once during the up immediately to prevent corrosion from
Environmental conditions which accel- winter and once immediately after the starting. If the chips or scratches have gone
erate corrosion winter. Keep your vehicle, particularly the through to the bare metal, have a qualified
1) Road salt, dust control chemicals, sea underside, as clean and dry as possible. body shop make the repair.
air or industrial pollution will all If you frequently drive on salted roads, your
accelerate the corrosion of metal. vehicle should be washed at least once a Keep passenger and luggage compart-
2) High humidity will increase the rate of month during the winter. If you live near the ments clean
corrosion par ticularly when the ocean, your vehicle should be washed at Moisture, dirt or mud can accumulate under
temperature range is just above the least once a month throughout the year. the floor mats and may cause corrosion.
freezing point. Occasionally, check under these mats to
3) Moisture in certain areas of a vehicle for For washing instructions, refer to the ensure that this area is clean and dry. More
an extended period of time may promote “Vehicle Cleaning” section. frequent checks are necessary if the vehicle
corrosion even though other body is used off road or in wet weather.
sections may be completely dry.
11-1 184
MH0-74E APPEARANCE CARE
Certain cargos such as chemicals, fertilizers, Vehicle Cleaning Rub the surface with a clean, damp cloth
cleaners, salts, etc. are extremely corrosive to remove dirt and the soap solution. If
by nature. These products should be some dirt still remains on the surface,
transported in sealed containers. If a spill repeat this procedure.
or leak does occur, clean and dry the area
Fabric upholstery
immediately.
Remove loose dirt with a vacuum cleaner.
Store your vehicle in a dry, well-venti- Using a mild soap solution, rub stained
lated area areas with a clean damp cloth. To remove
Do not park your vehicle in a damp, poorly soap, rub the areas again with a cloth
ventilated area. If you often wash your dampened with water. Repeat this until the
vehicle in the garage or if you frequently stain is removed, or use a commercial fabric
drive it in when wet, your garage may be cleaner for tougher stains. If you use a
damp. The high humidity in the garage may fabric cleaner, carefully follow the
cause or accelerate corrosion. A wet vehicle manufacturer’s instructions and precautions.
MH0-07-014
may corrode even in a heated garage if the Seat belts
ventilation is poor. WARNING Clean seat belts with a mild soap and
When cleaning the interior or exterior water. Do not use bleach or dye on the
WARNING of the vehicle, NEVER USE flammable belts. They may weaken the fabric in the
Do not apply additional undercoating solvents such as lacquer thinners, belts.
or rust preventive coating on or gasoline, benzene or cleaning
around exhaust system components Vinyl floor mats
materials such as bleaches or strong
such as the catalytic converter, Ordinary dirt can be removed from vinyl with
household detergents. The materials
exhaust pipes, etc. A fire could be water or mild soap. Use a brush to help
could cause personal injury or
started if the undercoating substance loosen dirt. After the dirt is loosened, rinse
damage to the vehicle.
becomes overheated. the mat thoroughly with water and dry it in
the shade.
Cleaning the Interior
Vinyl upholstery
Prepare a solution of soap or mild detergent
mixed with warm water. Apply the solution
to the vinyl with a sponge or soft cloth and
let it soak for a few minutes to loosen dirt.
185 11-2
APPEARANCE CARE MH0-74E
11-3 186
MH0-74E APPEARANCE CARE
187 11-4
GENERAL INFORMATION MH0-74E
GENERAL INFORMATION
Vehicle Identification Engine Serial Number
EXAMPLE
MH0-07-014
12-1 188
MH0-74E GENERAL INFORMATION
Radio frequency identification As seen from inside of the vehicle As seen from outside of the vehicle
(RFID) tag (if equipped)
As per Ministry of Road Transport and
Highways, the Radio frequency identification
(RFID) tag (1) is mandatory for each vehicle
for the purpose of electronic toll collection
or any other purpose as may be defined by
the Government of India.
In case of any damage to RFID tag or
replacement of front windscreen, please
contact your nearest Maruti Suzuki
Authorized workshop.
Note:
RFID tag needs to be registered by
government authorized agency (if
applicable).
(1) Any attempt to remove the tag from the
windscreen will result in permanent
damage to the tag.
Use of chemical cleaners to clean the
windscreen area where the tag is
mounted can damage the tag.
Use of any sharp objects on the tag can
damage the tag.
189 12-2
SPECIFICATIONS MH0-74E
SPECIFICATIONS
NOTE: M/T: Manual transaxle
Specifications are subject to change without AMT: Automated manual transaxle
notice.
13-1 190
MH0-74E SPECIFICATIONS
ITEM: Engine
Type K10B (DOHC)
Number of cylinders 3
Bore 73.0 mm
Stroke 79.5 mm
Piston displacement 998 cm3
Compression ratio 11.0 ± 0.4 : 1
ITEM: Electrical
Standard spark plug Nickel plug NGK KR6A-10
Battery 12V 34B19L
Fuses See “INSPECTION AND MAINTENANCE” section.
191 13-2
SPECIFICATIONS MH0-74E
13-3 192
MH0-74E SPECIFICATIONS
193 13-4
MH0-74E
MEMO
194
MH0-74E
MEMO
195
MH0-74E
MEMO
196
Prepared by
MARUTI SUZUKI INDIA LIMITED
Service Division
December, 2013
For round-the-clock on-road assistance, call Maruti On-road Service at 1800 4200#
#No STD code to be prefixed.
India's No. 1 Car Exchange Programme
1800 4200
PEACE OF MIND
CODE 02/12/2013/5000
Service Division
MARUTI SUZUKI INDIA LIMITED
Palam Gurgaon Road, Gurgaon - 122 015 (Haryana)
www.marutisuzuki.com