Professional Documents
Culture Documents
by M. Melito
ABSTRACT
IGBTs are used in a variety of switching very fast. However they must have very low
applications thanks to their attractive V CE(sat), and be very rugged. Existing
characteristics, particularly their peak current technology allows a compromise between
capability, ruggedness and simple gate drive switching speed, ruggedness and power
requirements. Until recently their use was dissipation.
limited to the electrical drive sector, where This paper gives a brief explanation of the
they were required to be fast like Power physics and structure of the device, and
MOSFETs and to have low conduction highlights the characteristics which make
losses like BJTs. IGBTs particularly suitable as power switches
As automotive ignition switches operate at in automotive ignition systems.
low frequencies, they are not required to be
AN484/1293 1/9
APPLICATION NOTE
2/9
APPLICATION NOTE
voltage and current levels simultaneously, release in the generation of the spark. All of
without damage or degradation of reliability. the stored electromagnetic energy tends to
This can be achieved only if the voltage and concentrate across circuit parasitic
current levels are within the boundaries of capacitances, charging them to high voltages
the guaranteed turn-off (Reverse Bias) Safe and putting the device in avalanche, with a
Operating Area (RBSOA); otherwise an aid risk of going into second breakdown and
network is required to shape the voltage failing. This problem is overcome by
and current waveforms. Current technology dissipating this energy on the power switch
allows the production of IGBTs with a square through a protection Zener placed between
RBSOA whose voltage boundary is the the collector and the base of the device,
BVCES, and whose current limit is at least which turns the device on as soon as the
twice the nominal current of the device; thus collector voltage exceeds the nominal Zener
an aid network is not needed. voltage (fig. 4a,4b). The usual way to indicate
b) In the case of disconnection of a spark the minimum energy the switch can absorb
plug, the ignition switch must be able to without damage is to specify the battery
absorb the energy that the coil is unable to voltage, the coil inductance and coil current,
the clamp voltage for the Zener and, if The worst case Icoil will also be specified,
present, the collector-to-emitter capacitance. and Lcoil at its maximum possible value:
With a reasonable margin for the current, Icoil = 8A
e.g. 8A, the switch must survive the switch-
off without load on the coil secondary side. Lcoil = 7mH
4/9
APPLICATION NOTE
This kind of specification is usually referred extremes of -40oC and 150oC due to the
to as the “use test” and it can be easily temperature increase caused by the
guaranteed for IGBTs . electrical power dissipated in the device itself.
1.3.4 Input characteristics The power dissipation of an ignition switch
The ignition switch must be specified to in a high energy ignition system reaches a
ensure that the current and voltage available maximum during the current limiting interval,
from the driving stage are enough to switch fig.5a, apart from a short, very high peak at
it on and off under all temperature conditions. the end of it due to the switch-off phase,
The input characteristics of IGBTs are similar fig.5b, and since the device is used in the
to that of a MOS, and they need a very linear mode the lower VCE(sat) has little
small amount of energy for switching; a influence in power dissipation. The junction
driving energy that is at least two orders of temperature must be kept below its
magnitude less than that needed by maximum allowable value by a heatsink
Darlingtons. Moreover, logic level IGBTs, whose thermal resistance must be calculated
such as the STGP10N50L, can be turned considering :
on with a gate voltage of as little as 3V. - the maximum ambient (under-hood)
1.3.5 Temperature range and power temperature,
dissipation - the maximum thermal resistance,
The electronic components in an automotive junction to case, of the switch
environment are expected to work in the so - the thermal resistance, case to heatsink,
called automotive under-hood temperature due to the contact.
range, -40oC to 100oC. The final criterion cannot be ignored, as in
However it is preferable to specify the critical some cases it can be comparable with the
parameters not only at room temperature, thermal resistance of the device itself.
but also at the junction temperature
5/9
APPLICATION NOTE
Although their structures are similar, the Figure 7: VCE(sat) versus tfall
physical operation of the IGBT is very
different from that of the Power MOSFET;
the IGBT is a minority carrier device, and its
behaviour is closer to that of bipolar
transistor. This is due to the p+ substrate
which, during conduction, injects holes in
the n- region, significantly reducing its
resistivity.
Because of the conductivity modulation, an
IGBT has lower power losses than a Power
MOSFET, and has a better efficiency than a
bipolar transistor because the emitter covers
the entire area of the die.
6/9
APPLICATION NOTE
7/9
APPLICATION NOTE
8/9
APPLICATION NOTE
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco -
Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
9/9