Professional Documents
Culture Documents
Catalogue
2012
Ph 0800 88 22 12 www.reids.co.nz
Welcome to Reid
Welcome to Reid Construction Systems, leading suppliers of lifting, reinforcing and connection systems,
providing solutions to the concrete construction industry for over 90 years.
Our engineered products are tried, tested and trusted by contractors throughout Australasia and we pride
ourselves with a rigorous quality assurance and testing regime, ensuring that the products are up to the
highest possible standard.
We aim to be much more than just a supplier of components to the concrete construction industry. We
work in partnership with you in all facets of planning, preparation, design, engineering certification,
forming, production, rigging, lifting, anchoring and bracing… all critical stages in the safe and efficient
manufacture and placement of concrete elements.
More comprehensive information on all our products are contained in the Reid range of Design Guides.
These can be downloaded from our website www.reids.co.nz. Hard copies are available for specifiers.
Reid provide a complimentary engineering advisory service to assist with specification of our range of
products. To use this service, call our engineering team on 0800 88 22 12.
This catalogue is a demonstration of our commitment to the industry and we hope you find it useful.
Ph 0800 88 22 12 www.reids.co.nz
Contact us
By Phone
Our trained Sales Service staff can efficiently take your order by phone. Sales Service can be
contacted at your nearest branch office or by calling the Toll Free number:
By Facsimile
The easiest way to order by facsimile is to complete your Purchase Order and fax it to one of
the following numbers:
Via Email
Please send orders to: sales@reids.co.nz
Literature
Comprehensive technical information, data sheets and design guides are available.
Technical information is on the Web Site, or can be obtained by calling 0800 88 22 12.
Contents
Anchors 10 SwiftForm™ 26
Swiftlift™Face Lifting Anchors 10 Aluminium Extruded Profile Section 26
Eye Anchors 11 End Caps 26
Edge Lift & Hairpin Anchors 11 G-Clamp 26
Extension Arms 26
Recess Formers 11 Magnet 27
Swiftlift™ Recess Formers Angle Bracket for Stack Casting 27
Plastic 11
Rubber 11 ReidForm™
Steel 12 Edgeform LVL 28
Steel Articulated 12 Extruded Fillet 28
Edge Lift Recess Formers 12 Brackets 28
Fillet 28
Assemblies 13 Fillet Cutter 28
Face Lifting 13 Formwork Sealant 28
Face Lifting - Puddle-in 13 Double Sided Tape 28
Edge Lifting 14
GENERAL FORM RELEASE AGENTS 29
Bar Chairs 14 SwiftRelease General Release Agent 29
PINZ 29
Crown Spacers 14
Retarders 29
Fast Clip Bar Chairs 14
Retarder Paper 29
Panel Bar Chairs 15
Removable Formwork Spikes 29
Slab Bar Chairs 15
Bar Chair (Misc) 15
Insitu Formwork 30
Concrete Bar Chairs 16
Reidbar™ Wingnuts 30
Reidbar™ Formwork Cone, Conduit, Washers & Grommets 30
Clutches 17
Swiftlift™ Clutch 17
Nox-Crete 31
Plate & Hairpin Clutch 17
FormCoat E Form Release Agent 31
Swiftlift™ Remote Release 17 Bio-Nox Biodegradable Form Release 31
K-Concentrate 31
zeus 18 Silcoseal Select BondBreaker 31
Formguard TJ 31
Accessories 19 Sprayers & Tips 33
Swiftlift™ Anchor Cover Plates 19 Accessories 33
Swiftlift™ Shear/Omega Bars 19
Panel Plates 19
Panel Pads 19
Pipe Chains 19
Hire 22
Clutches 22
Brackets 22
Aluminium Boxing - Hire 22
Mistake Plates 22
Post Tensioning Jacks 22
IDAT 23
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2011. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
4 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/01/11. This supersedes all previous versions.
Contents
rockbolting/ground reinforcing 40
Reidbar™ Domed Base Plates 40
Reidbar™ Spherical Washers 40
Reidbar™ Spider Centralisers 40
Kwik-Zip Centraliser 40
Safety Protective Caps 40
CORROSION PROTECTION 41
Noxyde Water Based Elastomeric Membrane 41
reidbrace ™ 42
Post-tensioning
Post-Tensioning Kits 44
Post-Tensioning Strand 44
5
Contents
RAMSET TOOLS 92
Angle Grinders 93
Laser Level 93
Vacuum Cleaner 93
Diamond Drilling 94
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2011. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
6 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/01/11. This supersedes all previous versions.
When is size
not a problem!
When it’s Reid’s new Reidbar 32mm
Threaded Insert of course!
Reidbar Threaded Inserts are designed
for casting into concrete to provide
fixing points for starter bars and
structural members to be anchored
securely to concrete.
7
contents
Anchors 10
Swiftlift™Face Lifting Anchors 10
Eye Anchors 11
Edge Lift & Hairpin Anchors 11
Recess Formers 11
Swiftlift™ Recess Formers
Plastic 11
Rubber 11
Steel 12
Steel Articulated 12
Edge Lift Recess Formers 12
Assemblies 13
Face Lifting 13
Face Lifting - Puddle-in 13
Edge Lifting 14
Bar Chairs 14
Crown Spacers 14
Fast Clip Bar Chairs 14
Panel Bar Chairs 15
Slab Bar Chairs 15
Bar Chair (Misc) 15
Concrete Bar Chairs 16
Clutches 17
Swiftlift™ Clutch 17
Plate & Hairpin Clutch 17
Swiftlift™ Remote Release 17
zeus 18
Accessories 19
Swiftlift™ Anchor Cover Plates 19
Swiftlift™ Shear/Omega Bars 19
Panel Plates 19
Panel Pads 19
Pipe Chains 19
Hire 22
Clutches 22
Brackets 22
Aluminium Boxing - Hire 22
Mistake Plates 22
Post Tensioning Jacks 22
IDAT 23
8
Concrete Lifting Ssytems
Concrete lifting systems
9
concrete lifting systems
Face Lifting Anchors
Swiftlift Anchors (Facelifting)
Part No. Anchor load Length Qty
group (T) (mm) (per box)
* Indent only
¹ Vary spacing to suit application.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
10 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
concrete lifting systems
2.
11
concrete lifting systems
Recess Formers
Swiftlift™ Recess Formers - Steel
Part No. Description Anchor Qty
load (per box)
group (T)
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
12 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
concrete lifting systems
13
concrete lifting systems
Assemblies & Bar Chairs
Edge Lift Assemblies
Part No. Description Anchor Panel Qty
load thickness (per box)
group (T) (mm)
2EREA090 2VREA090
2EREA090 Edge Lifting Assembly 2.5 100mm 25
5EREA120 Edge Lifting Assembly 5.0 150mm 25
2VREA090 Vertical Edge Lifting Assembly 2.5 100mm 25
5VREA120 Vertical Edge Lifting Assembly 5.0 150mm 25
Crown Spacers
Suitable for 6-20mm reinforcing.
5EREA120
Part No. Description Qty 5VREA120
(per box)
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
14 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
concrete lifting systems
Mesh Chairs
FCM20 ² Mesh Chair (20mm) 100
FCM25 ² Mesh Chair (25mm) 100
FCM30 ² Mesh Chair (30mm) 100
1.
FCM40 ² Mesh Chair (40mm) 100
FCM50 ² Mesh Chair (50mm) 100
Bar Chairs
BSOG120C ³ Bar Chair (120mm) 100
BSOG130C ³ Bar Chair (130mm) 100
BSOG150C ³ Bar Chair (150mm) 100 2.
Other Chairs
PS95* Pile Spacer 95mm OD x 16mm ID - 40mm cover 100
TS17 Trough Spacer 17.5 x 5mm 100
CBN25CR12 ¹ Circular Spacer ( 25mm) 100 3.
* Indent only item
15
concrete lifting systems
• Two quality types; standard and premium to suit the highest durability
requirements for international standards
• Consistent high compressive strength with resistance to tilting
• Excellent bond with insitu concrete - no hairline cracks between the spacer
and the concrete
• Extremely suitable for impermeable concrete
• Excellent chemical and fire resistance
• Consistent dimensional tolerances and do not deform under temperature
fluctuations
• Quick and easy installation with a number of fixing options available
• Has performed in large civil and construction projects throughout Australia
and New Zealand
APPLICATIONS
Other products are available for specific applications. Refer to the Max Frank catalogue
on the Reid website www.reids.co.nz.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
16 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
concrete lifting systems
1.
Department of Labour Code of Practice dictates that clutches be checked by a competent person on a regular basis and a record should be kept of all checks.
Contact Reid™ to arrange annual testing.
17
concrete lifting systems
Zeus
Zeus has been developed as a cost-effective combined
support and lifting bracket for flange hung ‘Double
Tee’ and ‘Ribbed’ precast floor units great than 150mm
deep.
The bracket has been designed in accordance with NZS/AS 1170 and
NZS 3101:2006.
It is the only hanger bracket to date that has been tested to the ‘Jenson
Protocol’ which recognises the combined diaphragm and beam
rotation stresses induced in flooring units under extreme loading.
Zeus is the best practice alternative to the “pigtail loop” detail which is
hard to justify using rational analysis.
Z3 Leg
7ELARRF Rubber
Recess Former Z4 Leg
7ELALE
Hairpin
Clutch
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
18 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
concrete lifting systems
Panel Plates
The use of colour coded plates allows easy identification to determine which precast
elements belong to each job.
Panel Pads
Eliminates staining and other issues associated with curing against precast elements.
SWIFT PIPE2* Two leg pipe chain for jointing pipes 1.2m long ea UL2
UL1
19
concrete lifting systems
Propping & Accessories
Props for Hire
Reid™ Props are lightweight high capacity braces for hire, suitable for positioning and stabilising precast elements, retaining walls,
tilt-up panels, block wall steel structures and formwork. The braces conform to NZS3404:1997 design standards and are able to
meet the requirements of the approved code of practice for “The Safe Handling and Erection of Precast Concrete.” Reid™ props are
easy to install, robust, screw adjustable up to 500mm and slotted holes to accommodate bolts with safety stop for easy erection.
Telescopic Props can be adjusted to any length between 5m to 8.4m with 500mm adjustments.
100mm
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
20 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
concrete lifting systems
Swift Shims
Part No. Thickness Colour Size Qty
(per box)
SHIM01 ¹ 1mm Red 100x90x1 100
SHIM03 ¹ 3mm Blue 100x90x3 100
SHIM06 ¹ 6mm Green 100x90x6 100
SHIM10 ¹ 10mm Black 100x90x10 100 1.
SHIM01L ² 1mm 100x150x1 100
SHIM02L ² 2mm 100x150x2 200
SHIM03L ² 3mm 100x150x3 100
SHIM05L ² 5mm 100x150x5 100
2.
SHIM10L ² 10mm 100x150x10 40
SHIM15L ² 15mm 100x150x15 40
SHIM20L ² 20mm 100x150x20 30
21
concrete lifting systems
Hire Products
Clutches - Hire
Part No. Description Qty
(per ea)
1LE 1.3 Tonne Swiftlift Clutch Hire only
1ELALE 1.3 Tonne Hairpin Clutch Hire only
2LE 2.5 Tonne Swiftlift Clutch Hire only
2ELALE 2.5 Tonne Hairpin Clutch Hire only
5LE 5 Tonne Swiftlift Clutch Hire only
5LE-R 5 Tonne Remote Release Clutch Hire only
7ELALE 7 Tonne Hairpin Clutch Hire only
10LE 10 Tonne Swiftlift Clutch Hire only
10ELALE 10 Tonne Hairpin Clutch Hire only
20LE 20 Tonne Swiftlift Clutch Hire only
32LE 32 Tonne Swiftlift Clutch Hire only
Brackets - Hire
Part No. Description Qty
(per ea)
PCB-HIRE Support Brackets for Panels while Propping Hire only
SCB-HIRE Stack Cast Bracket Hire only
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
22 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
Features & Benefits
Find out why IDAT is the only CAD package worth considering for precast.
√ √
Support Database
Local support from Reid in Keep track of your
your time zone and language projects materials
√ √
Customisation Autocad Interface
Set up IDAT the way If you can use Autocad we
you require it can train you in under a few days
Now your business can profit from a partnership between Reid Construction Systems
and IDAT of Germany that will revolutionise your approach to precast concrete.
PH: 0800 88 22 12
Develop your Business Solution today. Ask for a Free Demonstration.
Precast
Design a
Detailin nd
g
e Name Softwar
e!
From Th
s you Kn
ow and
Tru st!
www.idat.com.au
www.reids.co.nz 23
contents
SwiftForm™ 26
Aluminium Extruded Profile Section 26
End Caps 26
G-Clamp 26
Extension Arms 26
Magnet 27
Angle Bracket for Stack Casting 27
ReidForm™
Edgeform LVL 28
Extruded Fillet 28
Brackets 28
Fillet 28
Fillet Cutter 28
Formwork Sealant 28
Double Sided Tape 28
Nox-Crete 31
FormCoat E Form Release Agent 31
Bio-Nox Biodegradable Form Release 31
K-Concentrate 31
Silcoseal Select BondBreaker 31
Formguard TJ 31
Sprayers & Tips 33
Accessories 33
24
formwork systems
Formwork Ssytems
25
FORMWORK systems
SWIFTFORM
Aluminium Extruded Profile Section
Part No. Description Qty Qty
(per length) (per
Bundle)
End Cap
Part No. Description Qty
(per box)
G-Clamp
Part No. Description Qty
(per box)
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
26 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FORMWORK systems
Magnet
Part No. Description Qty
(per box)
Formwork Systems
SW3000MAG Magnetic Clamp c/w Bridge 1300kg holding force ea
KPB2000-PTOOL Magnet Clamp Release Lever ea
SWIFTFORM
Accessories
Part No. Description Qty
(per box)
27
FORMWORK systems
Accessories
Edgeform LVL
Part No. Description Lineal Recomm. Qty Qty
metres per support (per length) (per
pack spacing bundle)
Extruded Fillet
Part No. Description Qty Qty
(per (per bundle)
length)
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
28 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FORMWORK systems
Formwork Systems
SwiftRelease - General Form Release Agents
Oil based products for timber and steel.
Retarder Paper
For producing exposed aggregate.
Part No. Description Aggregate Qty
Size (per box)
new
Removable Formwork Spikes
Part No. Description Spike Qty
Length (per box)
29
FORMWORK systems
Insitu Formwork
Reidbar Wingnut
Part No. Bar Overall Overall Qty
dia length dia (per box)
Formwork Cone
RB12 Reidbar
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
30 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FORMWORK systems
Nox-crete™
Form Release Agents
Waterbased form release agents for steel/formply to concrete applications.
Formwork Systems
drum)
Bondbreakers
Water based curing agent and bondbreaker for concrete to concrete applications.
31
FORMWORK systems
Nox-crete™
BIO-NOX
Use On: Aluminium Forms; Plywood Faced Handset Forms; All Overlaid Plywood
Forms; Steel Forms; Plastic & Rubber Form Liners
• 100% biodegradable.
• Water based formulation.
• Does not oxidize or turn tacky. Produces smooth uniformly white
architectural concrete surfaces with no staining and substantially fewer
surface defects.
• Can be used with aggressive stripping schedules where forms are stripped
and repoured within 24 hours
FormCoat E
Use On: Plywood Faced Handset Forms; All Overlaid Plywood Forms; Steel
Forms; Plastic Form Liners
• Biodegradable
• Exceptional performance on non-overlaid plywood, dimensional lumber and
MDO plywood.
• Extends the life of wood forms by reducing the absorption of destructive
akaline bleed water.
• Produces smooth, uniformly white concrete surfaces with no staining and
reduced surface voids (bugholes).
SILCOSEAL SELECT
Use On: Tilt-up Concrete Panels
• New generation, chemically active cure and bondbreaker.
• Produces exceptional wall panel surface appearance
• Provides crisp positive release from casting beds
• Excellent resistance to rain wash-off once dry.
• Superior UV resistance allows longer periods between application and
concrete pours.
Bondbreaker Differences
Silcoseal Select Competitor Bondbreaker
When applied correctly, Silcoseal Select will not stain the panels. It’s new generation water based formula provides a uniform appearance in comparison to
other bondbreakers.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
32 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FORMWORK systems
Nox-Crete Quick Guide
Bio-Nox FormCoat E Silcoseal Select Silcoseal 77
Concrete to
Concrete to Concrete
Form Release Agent Concrete
Bondbreaker
Bondbreaker
Formwork Systems
Steel, rubber, plastic, Steel, all plywood, Concrete
Suitable for use on overlaid plywood, plastic, fibreglass, Concrete (Solvent based)
closed cell foams rubber
Coverage (m2/lt) 50 - 60 25 - 75 5-10 5 - 10
Dry Time @ 2o C 1/2 hour 1/2 hour 1/2 - 3 hour 1/2 - 3 hour
Application Method Spray Spray Spray, roller Spray, roller
Spray Tip Required NOXTIP80005 NOXTIP800067 NOXTIP8004 NOXTIP8004
Biodegradeable 100% Yes Yes No
Odour No Minimal Minimal Mild
Flammable No No No Yes
Trafficable when dry Partly Yes Yes Yes
Non-slippery when dry No Yes Yes Yes
Rain resistant when dry Yes Yes Yes Yes
Clean-up Water Water Water Sugar Soap
33
contents
reidbar™ components 36
Reidbar™ Couplers 36
Reidbar™ Nuts 36
Reidbar™ Foot Plates 36
Reidbar™ Flange Nuts 37
Reidbar™ Grout Sleeves 37
Reidbar™ Grout Sleeve (setting hardware) Grout 37
Reidbar™ Wing Nuts 37
Reidbar™ Threaded Inserts 38
Reidbar™ Reduced Threaded Insert 38
Reidbar™ Threaded Insert Chair 38
Reidbar™ Plastic Nail Plates 38
Reinforcing Grommets 38
rockbolting/ground reinforcing 40
Reidbar™ Domed Base Plates 40
Reidbar™ Spherical Washers 40
Reidbar™ Spider Centralisers 40
Kwik-Zip Centraliser 40
Safety Protective Caps 40
CORROSION PROTECTION 41
Noxyde Water Based Elastomeric Membrane 41
reidbrace ™ 42
Post-tensioning
Post-Tensioning Kits 44
Post-Tensioning Strand 44
reidbar components
Reidbar Components
REIDBAR COMPONENTS
Reidbar™ Components
Reidbar Coupler
Threaded coupler for joining sections of Reidbar™
Part No. Bar Overall Hex Qty
dia. Ø length A/F (per box)
RB12C
reidbar
RB12
components
90mm 25mm 100
RBA16C RB16 102mm 30mm 60
RB20C RB20 116mm 36mm 32
RB25C RB25 180mm 45mm 20
RB32C RB32 210mm 57mm 10
Galvanised
RB12CG RB12 90mm 25mm 100
RBA16CG RB16 102mm 30mm 60
RB20CG RB20 116mm 36mm 32
RB25CG RB25 180mm 45mm 20
RB32CG RB32 210mm 57mm 10
Reidbar Nut
Part No. Bar Overall Hex Qty
dia. Ø length A/F (per box)
RB12N RB12 40mm 25mm 210
RBA16N RB16 45mm 30mm 100
RB20N RB20 50mm 36mm 82
RB25N RB25 65mm 46mm 36
RB32N RB32 82mm 55mm 18
Galvanised
RB12NG RB12 40mm 25mm 210
RBA16NG RB16 45mm 30mm 100
RB20NG RB20 50mm 36mm 82
RB25NG RB25 65mm 46mm 36
RB32NG RB32 82mm 55mm 18
Half Nuts Galvanised
RB12NHG RB12 18mm 25mm 420
RBA16NHG RB16 20mm 30mm 200
RB20NHG RB20 23mm 36mm 164
RB25NHG RB25 31mm 46mm 72
RB32NHG RB32 39mm 55mm 36
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
36 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
REIDBAR COMPONENTS
Reidbar™ Components
Reidbar Flange Nut
Reidbar™ Flange Nuts have a continuous thread. Should you require a stop in the end for the larger sizes,
A RB12WN is used instead of a 12mm Flange Nut. please refer to the Reidbar Design Guide.
Reidbar Components
RBA16FNG RB16 51mm 30mm 60
RB20FNG RB20 50mm 36mm 30
RB25FNG RB25 70mm 46mm 16
RB32FNG RB32 95mm 57mm 7
Reidbar Wingnut
Part No. Bar Overall Overall Qty
dia length dia (per box)
37
REIDBAR COMPONENTS
Reidbar™ Threaded Inserts
Reidbar Threaded Inserts
Designed for casting into concrete and provide fixing points for attachments of starter
new
bars and structural members to be bolted directly to the concrete structure.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
38 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
REIDBAR COMPONENTS
Metric THREADED INSERTS
Reid Threaded Insert Metric (TIM or TCM)
Other sizes of Metric Threaded Inserts are available on request.
Note: This product may be called TCM’s.
Reid TIM
Part No. Thread Cross Hole Thread Anchor Qty
size diameter depth Length (per box)
Reidbar Components
TIM12X50G M12 9.1/9.5mm 20mm 50mm 100
TIM16X75G M16 11/11.6mm 35mm 75mm 25
TIM20X75G M20 15/15.5mm 32/33mm 75mm 50
TIM20x120G M20 47mm 120mm 20
TIM24X100G M24 20/20.5mm 45mm 90mm 20
316 Stainless Steel TCM’S with Elephant Foot NEW RANGE!
TCM10X45SS M10 8.4mm 20mm 45mm ea Reid have released a
SS TCM
range of Stainless Steel
TCM12X55SS M12 8.4mm 25mm 55mm ea
Inserts with an Elephant
TCM16X70SS M16 11.0mm 32mm 70mm ea Foot. Look for the new
TCM20X95SS* M20 11.0mm 35mm 95mm ea Technical Catalogue on
the website.
* Indent only
39
REIDBAR COMPONENTS
Kwik-Zip GT Centraliser kWIK-zip bows come as an each item. They are assembled in
Suitable for Rock Bolts, Soil Nails and Small Diameter Bar. accordance with bar size (pieces per Kwik-zip) and hole diameter
size. Centralisers should be used approx every 1.5-2m depending
Part No. Bar size Pieces per Qty on length of hole and weight of bar.
(mm) OD over Centraliser (per box) Bow heights are 20, 30, 40mm.
thread per location For further information contact Reid.
RBKZ-GT20 18-29mm 2 100
RBKZ-GT30 29-46mm 3 100
RBKZ-GT40 47-65mm 4 100
* Indent only
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
40 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
REIDBAR COMPONENTS
Corrosion Protection
Noxyde Water Based Elastomeric Membrane (NEW)
Part No. Description Size Qty
(per box)
RBNOXB1 Noxyde Paint On Membrance - Black 1kg ea
RBNOXB20* Noxyde Paint On Membrance - Black 20kg ea
RBNOXG1 Noxyde Paint On Membrance - Mist Grey 1kg ea
RBNOXG20* Noxyde Paint On Membrance - Mist Grey 20kg ea
Noxyde is a water based elastomeric membrane which provides corrosion protection and waterproofing. It
is recommended for use on Reidbar and Reidbrace applications. For more information on the use of this
Reidbar Components
product and suitable applications refer to the Reid website www.reids.co.nz.
ADHESION
For further details refer to product data sheets. (www.ro-m.com)
Your distributor:
Even when the membrane is cut, its incredible adhesion will prevent any type of
undercutting by corrosion and therefore corrosion is not able to spread.
REVOLUTION IN
WATERPROOFING CORROSION CONTROL
Noxydizing is impermeable for water. This strength and its excellent elasticity
make it the best solution for the protection and waterproofing of metal roofs and
cladding.
EXCELLENT EDGE COVERAGE Rust-Oleum Netherlands B.V. Rust-Oleum UK Ltd. Rust-Oleum France S.A. Rust-Oleum Mathys Italia s.r.l. N.V. Martin Mathys S.A.
MFNOXY.GB - 09.04
P.O. Box 138 Unit 5D Alexandra Way, 11, rue Jules Verne - B.P. 39 Via Mazzetta, 36 Kolenbergstraat 23
Corrosion usually begins on outside edges where there is minimal film build.
4700 AC Roosendaal Ashchurch B. Centre 95322 St-Leu-La-Forêt Cedex 13856 Vigliano Biellese BI 3545 Zelem
The Netherlands Tewkesbury GL20 8 NB France Italy Belgium
T: +31 (0) 165 593 636 United Kingdom T: +33 (0) 130 40 00 44 T: +39 015 81 22 160 T: +32 (0) 13 460 200
F: +31 (0) 165 593 600 T: +44 (0) 1684 27 33 33 F: +33 (0) 130 40 99 80 F: +39 015 81 22 161 F: +32 (0) 13 460 201
info.nl@ro-m.com F: +44 (0) 1684 27 33 31 info.fr@ro-m.com info.it@ro-m.com info.be@ro-m.com
www.ro-m.com info.uk@ro-m.com www.ro-m.com www.ro-m.com www.ro-m.com
www.ro-m.com
Testing proofs a 100% edge coverage at a round corner and still a 41% coverage at
a 90 degree corner.
41
REIDBAR COMPONENTS
reidbar
Part No.
components
Description Pin hole
dia. Ø
Qty
(per box)
Sets
RBRACE12-SET Reidbrace Set RB12 17mm ea
Reidbrace has many innovative applications as the banana and the end can be used in separate installations with out the other.
For values on the Reidbrace, refer to the Reidbar Design Guide available from the web.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
42 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
REIDBAR COMPONENTS
Dowels
DID YOU KNOW?
McDowel Bearing Strip McDowel Bearing Strip has been tested by Canterbury
Bearing strips are designed to be placed between precast concrete floor slabs University Research? You can view the reports on line
and a supporting wall or beam. The Bearing Strips then allow the slabs to be slid into at www.reids.co.nz.
place without incurring damage to either the slab or the supporting wall or beam.
Reidbar Components
Dowelsert Slab Insert
Keeps slabs vertically aligned across construction joints while allowing lateral
displacement due to differential shrinkage)
43
POST TENSIONING
Post-Tensioning is a method of applying a
compressive load to a concrete element after it
has been poured.
Applications
• Floors and foundations on grade.
• Precast wall panels.
• Strongback replacement.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
44 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
stressfloor
CONCRETE FLOORs
Post Tensioned Floor System for Slabs-on-Grade
• Easier to construct
45
contents
Flexus 50
Modular Floor System
Modular Stair System
Shotbond
Flexus Installers
Flexus Pre-Bagged Mix 53
formliners 54
architectural design with concrete
Architectural Design
architectural design
Nirvana
Nirvana Connector Pin
Part No. Description Qty
We recommend Koolfoam’s Black Pearl® EPS Polystyrene. For further information Koolfoam BLACK PEARL® Slab Insulation
view our website www.reids.co.nz. Koolfoam THERMALOCK® jointing system
Part No. Description Qty ADVANTAGES Koolfoam BLACK PEARL® Slab Insulation
• 20% better thermal performance than white EPS
ADVANTAGES Koolfoam
THERMALOCK® jointing system
• Thinner sheets can be used to achieve relevant R values • No sheet separation
• No glare when installing • Eliminates thermal bridges
• Low water absorption • Speed construction
• Excellent compressive strength
North Island
• Increased Eco efficiency
• Complies with all aspects of AS1366 1992
KOOLFOAM LIMITED
34 Grayson Ave, Papatoetoe, Auckland, New Zealand.
* Indent only
OBSERVATIONS:
• In a side-by-side comparison in an actual application, Type I EPS out performed XPS on both R-value
retention and water absorbtion.
• The study highlights that short-term immersion testing is not a good indication of how insulation performs
on actual construction sites.
*Tests as per the INSULFOAM LLC -TECHNICAL CENTER, Technical Bulletin No. 22.
For more information on the test information and conclusion, please contact Reid on 0800 88 22 12.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
48 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
architectural design
flexus™ a ‘bendable’ concrete innovation
Reid™ has pioneered a breakthrough in a high performance fibre-reinforced engineered cementitious composite
(ECC) that provides the structural integrity of reinforced concrete but without the weight or thickness. The new
design medium branded Flexus™, has unique properties such as ductility and improved durability, however its most
important feature is its ability to strain harden under tensile or flexural loads. Flexus™ can be sprayed or poured to
produce a multitude of products for the construction industry. For more information on the Flexus™ range, visit our
web site www.flexus.co.nz.
Flexus
PH: 0800 88 22 12 49
Flexus™ Stair System
The custom moulded treads and risers, and their long span
properties reduced the need to fully frame and fire rate the
support structure. Its natural self finishing concrete look
combined with exposed structural steel and glass panels
created a functional staircase, with an industrial prefab look.
The building has been erected over essential car parks for the
hospital and due to this, the building has been designed to be
broken down and re-erected on another site within the hospital
grounds within four years.
Flexus
exceeded Arrow’s expectations.
Due to the possible relocation of the building, coach screw fixings Cllient Middlemore Hospital
were chosen over the standard skew nail fixings, which will allow Architectural Designer: JASMAX
the flooring modules to be easily dismantled when required. Engineering: Holmes Consulting Group
Main Contractor: Arrow International
Arrow’s Site Project Manager, Kevin Giddings, commented,
“ I bet you didn’t even expect it to go up as quick
or as easy as it did ”
PH: 0800 88 22 12 51
Flexus™ Shotbond
From Auckland’s first dump site to a site of historic significance the Victoria
Park Market, which is currently under redevelopment, is now one of
Auckland’s most recognised landmarks.
Eight tenants are set to move in once the project, which includes restaurants,
nightclubs and a new retail precinct, is completed.
Victoria Park Market in Freeman’s Bay, exemplified by the thirty eight metre
high chimney, was erected in 1904. The complex is a Category 1 Historic
Places building under the Historic Places Act 1993, hence the decision to
structurally retrofit the chimney to ensure one of Auckland’s iconic landmarks
would be around for many years to come.
A 20mm lining of Flexus™ Shotbond was sprayed onto the inside surface of
the brick chimney which gave it strength and ductility to resist lateral, seismic
and wind loadings while preserving the heritage significance of the landmark.
“Thanks to the team at Reids for working with us to meet the specific
requirements for this unique project.
A great product that will last the test of time”.
Tony Howard , CMP Construction
Flexus™ Shotbond
Modular Flooring
Contact: Warwick Pirie
Mobile: 027 577 1140
Email: warwick@modular.net.nz
Wilco Precast
Contact: Colin Beavis 740mm
265mm
Phone: 190mm 09 295 1060 120mm
90mm 30
355mm
Email: colin@wilcoprecast.co.nz
Flexus
355mm
25mm step
25mm step
100mm
50mm
FSM
DESCRIPTION
Flexus Structural Shotbond Pre-mix is a cementitious blend, which
mixed with clean water, produces a structural mortar with unique
tensile strain hardening and flexural properties.
quality.
structural mortar with unique
680mm
SURFACE PREPARATION
Concrete surfaces should be clean and free from surface
contaminants. tensile strain hardening
We recommend “hydro blasting” all substrates that will be Shotbonded.
Dry concrete substrates should be saturated with water before
application of Shotbond.
and flexural properties.
STI 00000 DET 0000000 00/00/07
MIXING
Mixing must only be done in a specified mixing apparatus. No other
530mm
apparatus to be used.
Casting Mix
Description Colour
CURING
95% of curing will be achieved after 28 days. For best results, cure at
20°C for the first 24 hours at least (above 5°C is essential) and
maintain a high relative humidity of 95% for the first 7 days. Best way
is either to keep moist or use an appropriate curing membrane.
XX%
HANDLING PRECAUTIONS
RISK
Cement can cause respiratory, eye and skin irritation. Wet Flexus can
be corrosive to skin and eyes and may cause dermatitis. Repeated
inhalation of dust should be avoided.
SAFETY
Wear suitable dust mask, protective clothing, gloves and eye innovative | flexible | versatile | superior | flexus
protection. Wash hands thoroughly after handling this product.
Shotbond Mix
FIRST AID
Flush eyes with plenty of water and seek medical attention
immediately if symptoms persist. Wash skin with clean water.
Flexus
SPILLS/LEAKS
Keep out of storm water and sewers.
Shotbond
Due care and attention must be undertaken in the manual handling of
this bag to avoid personal injury.
DISCLAIMER
Mix
Reid Construction Systems and ITW New Zealand LTD accepts no
liability for damages or injury arising from the use of its products.
Batch Number:
FSM
REID CONSTRUCTION SYSTEMS a division of ITW New Zealand LTD
Customer services
Ph: 0800 88 22 12 Fax: 0800 88 22 55
Head Office
23 - 29 Poland Rd, Wairau Valley, Glenfield, Auckland, New Zealand
www.flexus.co.nz
FSM
For all Flexus sales and enquiries please call sales service on 0800 88 22 12. To be used by approved
Flexus Applicators only
NET CONTENTS
20 kg
100mm
50mm
25mm step
530/355/120
25mm step
PH: 0800 88 22 12 53
FORMLINERS
architectural design
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
54 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
architectural design
Vac-U-Form™ Formliners
Single-use and Multi-use Single-use: Vac-U-Form Single-Use formliners are made from a high-impact styrene
plastic. They are a cost-effective choice when formliners are to be used once or need to be
plastic Formliners for
cut to fit the project parameters.
tilt-up and cast-in place
applications.
Technical Data ASTM
IZOD Impact 2.0 D256
Tensile Strength 25.5 MPa D638
Heat Deflection 86.7°C D695
Vicat Softening 100°C D1525
Wt. kg/m² 2.28mm 2.47 kg/m²
Architectural Design
IZOD Impact, ft.-lb/inch
Hammer Lane, Stockton, California @ 22.8°C 2.99 J/cm D256
Application: Cast-in-place @ 4.4°C 1.01 J/cm
Formliner: Fitzgerald Vac-U-Form Tensile Strength 22.8°C, psi
Pattern: No. 16959 with Custom Geometric Panels
Yield 36.54 MPa D638
Modulus 2275.27 MPa
Flexural Strength 22.8°C, psi
Yield 64.12 MPa D790
Vac-U-Form Formliners are an alternative and
Modulus 2240.73 MPa
economical choice where single or limited re-use
Falling Dart Impact, ft.-lb
is desirable. @ 22.8°C 31.18 J
@ 4.4°C 18.98 J
Benefits Heat Deflection Annealed
@ 1.82 MPa 92.8°C D648
• Economical for limited usage
@ 0.46 MPa 99.4°C
• Lightweight
Hardness 22.8°C Rockwell R 105 D785
• Design versatility
Specific Gravity 1.05 D792
• Easy to field cut
Wt.kg/m² 2.28mm 2.48 kg/m² (Approx.)
3.81mm 4.76 kg/m² (Approx.)
Vac-U-Form formliners provide unlimited design
versatility. Many patterns match side-to-side and
top-to-bottom on standard 1210 x 2430mm and Manufacturing Tolerance
1210 x 3040mm panels.
Length: +/- 3mm at time of manufacture
Normal shrinkage and expansion is approximately 2mm in 3040mm with each 6.67° C
change in temperature.
55
architectural design
VinyLok™ Formliners
Interlocking extruded Benefits
plastic Formliners for • Lower labor costs • Fast installation
tilt-up, precast and cast-in • Seamless finishes • Less concrete leakage, grinding,
place applications. • Design flexibility sacking or patching
VinyLok Single-Use and Multi-Use formliners are offered in a wide variety of standard
geometric patterns or can be fabricated for custom designs. Almost any linear design can be
produced easily.
Technical Data
Single-Use High-Impact Styrene ASTM
IZOD Impact 2.0 D256
Tensile Strength 25.51 MPa D638
Heat Deflection 86.7°C D695
Vicat Softening 100°C D1525
Lifetouch Building, Kansas City, Kansas Wt. lb./sq.ft. .090mil 2.47 kg/m²
Application: Tilt-up
Formliner: Fitzgerald VinyLok
Pattern: No. 14302 Multi-Use ABS ASTM
IZOD Impact
VinyLok formliners are extruded in lengths up to @ 22.8°C 2.99 J/cm D256
@ 4.4°C 1.01 J/cm
12.2m for use in tilt-up, precast and cast-in-place
Tensile Strength 73° F, psi
concrete applications. The unique interlocking
Yield 36.54 MPa D638
system provides the ideal solution for projects Modulus 2275.27 MPa
where a seamless finish is required. Flexural Strength 73° F, psi
Yield 64.12 MPa D790
Modulus 2240.80 MPa
Falling Dart Impact, ft.-lb.
@ 22.8°C 31.18 Joules
@ 4.4°C 18.98 Joules
Heat Deflection Annealed
@ 1.82 MPa 92.78 °C D648
@ 0.46 MPa 99.44 °C
Hardness 73° F Rockwell R 105 D785
Specific Gravity 1.05 D792
Wt.kg/m² 2.28mm 2.48 kg/m²
3.81mm 4.76 kg/m²
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
56 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
architectural design
GrayLastic™ Formliners
Extended-use elastometric
Formliners for precast and
cast-in place applications.
Architectural Design
Pattern: Antietam Drystack, No. 17910
GrayLastic formliners provide maximum design Fitzgerald’s GrayLastic formliners accurately reproduce virtually any design. Wood, stone,
latitude for precast or cast-in-place applications. masonry, fractured rib, fluted rib, sandblast and a range of custom patterns are available.
They are re-usable up to 100 times, and are GrayLastic has been used in numerous artistic applications, whether cast-in-place or precast.
especially economical for applications that A seamless finish can be achieved through our interlocking patterns as well as with our side-to-
require an extended, reusable formliner. side, top-to-bottom match points.
Benefits Many patterns are available in sizes up to 30’ long, and all GrayLastic formliners can be easily
• Economical for extended usage field-cut. Odd sizes or custom fabrications are available for special applications.
• Realistic replication
• High durability Technical Data ASTM
• Seamless finishes
Shore A Hardness 50-55 D2240
• Wide range of sizes
Cast Density, PCF 55-60
• Easily installed
Tear Strength, PLI 90 D624
GrayLastic elastomeric formliners are Tensile Strength, psi 5.31 MPa D638 (D412)
manufactured from 100% polyurethane and are Ultimate Elongation 275% D638 (D412)
usually mold bonded to plywood. They are easily
attached to most concrete forming systems,
including wood, steel, aluminum and fiberglass. Manufacturing Tolerances
57
architectural design
Fitzgerald Formliners, distributed by Reid pride themselves on the design and manufacture of the best formliners in the industry, focusing
their efforts solely on the continuous improvement of their products. Proprietary products such as - GrayLastic™, GrayLite™, Vac-U-
Form™ and VinyLok™ are some innovative formliners available in the construction market. With more than 250 standard and custom
patterns, we can offer an unrivalled variety of design options from seven categories of pattern types.
Pattern categories include fluted ribs, fractured ribs, masonry, sandblast, stone & rock, wood textures and geometric shapes. From
conceptual design through to the final product, The attention to detail, quality and engineering guarantees the most creative and cost-
effective solution for your project.
Reid is proud to announce the local release of a select range of formliner patterns. These patterns will be stocked in Reid central
warehouse located in Melbourne, and will be available for immediate despatch. Delivery lead times may vary as single-use extruded and
vacuum formed sheets will require special handling, packaging and transportation. Stock availability is also subject to the parameters
and requirements of the specific project. Arrangements can be made for high-volume requirements, although longer lead times will be
applicable.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
58 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
architectural design
Architectural Design
VinyLok™ formliners are extruded in a single use, rigid polystyrene
plastic. The formliners are extruded in lengths of 9 metres and
offer approximately 150mm in width per single sheet. The patented
VinyLok™ interlocking system allows for a seamless finish for concrete
walls in tilt-up, precast or in-situ applications. VinyLok™ features
an interlocking nailing strip, designed for simple fixing of the liner to
formwork or concrete slabs. The patented rib easily locks over the top
of the fasteners, providing seamless concrete finishes with no unsightly
VL nail head impressions or grooves reflected in the cast panel. VinyLok™
VinyLok™ Single Use Interlocking is quick and easy to assemble and the interlocking nailing strip
eliminates the need for patching.
Formliners
59
architectural design
WOODEN PLANK
VS VS VS
MA WP SR
16971 16020 16986
Splitface Running Rough Sawn Plank Georgetown Ashlar
Bond Brick 3048mm W x 1220mm H 3048mm W x 1220mm H
2440mm W x 1220mm H Board Widths: 110mm Block Widths: 228-736mm
Max. Liner Depth: 19mm Max. Liner Depth: 3mm Block Heights: 127-381mm
Max. Liner Depth: 38mm
WOODEN PLANK
VS VS VS
MASONRY
MA WP SR
16947 16923 17002
200mm Used Brick Barn Wood Grain Austin Ashlar
Running Bond 3048mm W x 1220mm H 2440mm W x 1220mm H
1220mm W x 2440mm H Board Widths: 76-175mm Stone Widths: 127-686mm
Max. Liner Depth: 6mm Max Liner Depth: 6mm Block Heights: 50-356mm
Max. Liner Depth: 25mm
WOODEN PLANK
FZ VS VS
MASONRY
MA WP SR
16941 16928 16980
200mm Smooth Brick 150mm Ship Lap Plank Yosemite Rock
Running Bond 3048mm W x 1220mm H 1220mm W x 3048mm H
924mm W x 688mm H Max Liner Board Width: 152mm Max. Liner Depth: 19mm
Depth: 6mm Max. Liner Depth: 25mm
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
60 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FLUTED RIB architectural design
FLUTED RIB
FLUTED RIB
VL VL VL
FL FL FL
14304 14308 14542
152.4mm W x 9m Long 203.2mm W x 9m Long 152.4mm W x 9m Long
On Centre: 50.8mm On Centre: 101.6mm On Centre: 152.4mm
Pattern Peak: 19.05mm Pattern Peak: 25.4mm Pattern Peak: 25.4mm
Pattern Valley: 19.05mm Pattern Valley: 25.4mm Pattern Valley: 101.6mm
Max. Liner Depth: 19.05mm Max. Liner Depth: 25.4mm Max. Liner Depth: 19.05mm
Architectural Design
FRACTURED FIN
VS
FF
16951
Sahara Fin
1220mm W x 3048mm H
Maximum Liner Depth: 25mm
GEOMETRIC
VS
GE
20003
Western Range Grass
2702mm W x 914mm H
Maximum Liner Depth: 19mm
61
contents
ORBIPLATE 64
Orbiset 64
Flat Square Washers 64
CAST-IN CHANNEL 65
CORRUGATED TUBE 65
Grout 66
ACCESSORIES 67
Weldplates 67
Backing Rod 67
construction chemicals 68
Foam 68
Acrylic Sealant 68
Polyurethane Sealant 68
Formwork Sealant 68
Sealant Gun Accessories 68
SEALERS 69
Hardeners and Sealers 69
Panel Connections
PANEL CONNECTIONS
Orbiplate™
What is the Reid™ Orbiplate™ Connector?
The Reid™ Orbiplate™ Connector is a patented eccentric plate assembly which is used
for providing tolerance in all directions when connecting structural steel work and
concrete components. The Orbiplate™ is comprised of three parts. The outer and inner
plates have concentric and eccentric circular holes. The inner plate has two holes to
suit M16 and M20 fixing bolts.
No site welding, no drilling and no waiting! All welding is completed at the structural
steel yard. Orbiplate™ has a prepared edge for easy welding. No drilling on site is Cross-section diagram
required - no costly remedial work necessary. with Reid Metric Threaded
Insert cast into the concrete
component. A structural bolt
completes the final connection.
Integrity of Connection
A structural connection is achieved with a spanner and the use of an 8.8 structural bolt.
A Reid™ Metric Threaded Insert provides the necessary connection into concrete and
ensures the integrity of the connection.
Cost Saving
Orbiplate™ provides a quick and efficient connection, thus resulting in a faster
installation with less crane time. No power to location or electrical tools are required.
All the structural steel beams had Orbiplate’s welded to them for ease
of connection to the concrete panels.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
64 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
PANEL CONNECTIONS
Cast-in Channel
Cold Rolled / Not Toothed Channels
Suitable for light to medium duty connections, for tensile and limited shear loads.
T-Bolts
Suitable for heavy duty connections - relative to channel size as per tables above.
Head Size
Part No. Finish Metric Size Head Length Qty
Width
Panel Connections
HZS3823M1660H High Tensile M16 41.0mm 60mm ea
• Ideal for electrical & mechanical • Ideal for precast panel to panel connections.
services. • Ideal for beam to precast panel connections.
• Can also be used for curtain wall • No on-site welding required for panel connections.
or elevators depending on design • Full load capacity in all directions
requirements. • Able to take dynamic loads well
All cast-in channels are supplied hot dip galvanised. Other finishes and channel lengths are available on request. Refer to
Reid™ Cast-In Channel Technical Information catalogue on the website www.reids.co.nz.
65
PANEL CONNECTIONS
Corrugated Tube
Corrugated Tube is used as a duct former for a variety of precast
and cast-insitu concrete work. The semi-rigid hot dipped galvanised
metal duct is strong and durable for casting into concrete and is
easily tied into position adjacent to reinforcing steel.
Applications
• Service penetrations.
• Post-tensioning ducts.
• Precast connections.
• Formers for starter bars.
Corrugated Tube
Part No. Descriptions Qty
Grout
Precision, non-shrink grout suitable for use with grout sleeves, corrugated tube or
post tensioning systems.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
66 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
PANEL CONNECTIONS
Accessories
Weldplates
(w)
Part No. Anchors Thickness Concrete Length Width Qty
(l)
Steel Plate Panel (l) (w) (per box)
Thickness
WP200/120 1 10mm 120mm 200mm 150mm ea
concrete
WP200/150 1 10mm 150mm 200mm 150mm ea
panel
WP300/120 2 10mm 120mm 300mm 150mm ea
thickness
WP300/150 2 10mm 150mm 300mm 150mm ea
* Reid™ Engineering Design service can make custom order weldplates at your
request. Contact us on 0800 88 22 12, for further information.
Backing Rod
Part No. Descriptions Qty
(per box)
Panel Connections
67
PANEL CONNECTIONS
Construction Chemicals
Formwork Sealant
Part No. Descriptions Qty
(per box)
SABGU37
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
68 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
PANEL CONNECTIONS
TM
ChemSet Epoxies
Ramset Chemset Epoxies are a two part low viscosity high strength epoxy for injection of cracks in all concrete
elements. It offers excellent adhesion and high compressive strength and restores the structure to its original
monolithic condition.
Epoxies
Chemset Silca & Sand-filled Jointing System
Part No Description
EPTGE131-1.2KG Trowel Grade e131 Thixotropic Putty 1.2KG
Panel Connections
Two part epoxy concrete bonding agent
Part No Description
epube132-1.2kg Ultrabond e312 1.2KG
69
PANEL CONNECTIONS
Patching, Plastering & Rendering
Magic Patch
Magic Patch is a lightweight concrete patching mortar. It is blended from high grade
materials to provide a non-structural patching mortar to remedy visible joining plates,
threaded insert and bug holes. Recommended for non-structural patching of precast
and tilt-up concrete panels, but can be also used for a wide range of other concrete
repairs.
Magic Coat
0800 88 22 12
Magic Coat is a “Do It Yourself” easy to use “One Coat” grey architectural finish designed
to be used on a variety of concrete products and substrates to cover unsightly concrete
surfaces with an architectural ‘Render’ look at a cost effective price.
Glowmarkers
Part No. Descriptions Qty
(per box)
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
70 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
PANEL CONNECTIONS
TM
ChemSet Crack Injection System
Ramset Chemset Crack Injection System is a two part low viscosity high strength epoxy for injection of cracks in all concrete
elements. It offers excellent adhesion and high compressive strength and restores the structure to its original monolithic condition.
Approved applicators can install on your project. Contact your local representative to discuss.
Panel Connections
Ramset Chemset Crack Repair Epoxy Mortar is a solventless epoxy mortar or concrete
binder designed for applications demanding high structural integrity. When mixed with
graded sand fillers it produces various consistencies. Ramset Chemset Epoxy Mortar is
100% solids epoxy with negligible shrinkage. Ramset Chemset Epoxy Mortar has been
independently tested and meets the requirements of AS/NZS 4020 - 2002 for use in
contact with potable water.
Areas of application
• Structural bonding of new to old concrete
• Repairing cracks in concrete
• Structural repair of spalled concrete and masonry
• Grouting of load bearing bolts and supports in concrete
• Splash zone repairs to concrete and timber piled structures
Features
new
• Multi-purpose use
• High mechanical strength
• Low viscosity
• High chemical resistance
• Excellent adhesion to wet or dry concrete
• Non-shrink
• Low temperature cure
• Aggregate extendible
71
contents
FASTENING ANCHORS 79
Flanged AnkaScrew-in Anchors 79
Removable Formwork Spikes 79
Concrete Nails 79
Trubolt™ 80
CHEMSET ™ 84
Chemset™ Stud Anchors 84
Chemset™ Maxima Spin Capsules 84
Chemset™ Accessories 84
Chemset™ Allthread Rod 85
Chemset™ Couplings 85
DYNASET ™ DROP IN ANCHORS 86
Dynaset™ Drop In Anchors 86
Dynaset™ Setting Tools 86
RAMSET TOOLS 92
Angle Grinders 93
Laser Level 93
Vacuum Cleaner 93
Diamond Drilling 94
72
Fasteners & Tools
73
FASTENERS & TOOLS
Liebig Heavy Duty Anchors & Component Sets
Part No. Anchor Drill/Anch Min Hole Anchor Qty
Size or Dia. Depth Length (per box)
Liebig Superplus BLS Carbon steel, zinc plated Self Undercut Anchors
Øx Max. Eff.
Thread Ø Fixture Total Box
Reid Liebig Depth of Fixture Embedment Weight
Size Hole Length Quantity
Product Code Product Code Drilled Hole Thickness Depth
do x h1 tfix df hef L
[mm] [mm] [mm] [mm] [mm] [mm] [kg/100 pcs] [pcs]
SPS14/130 BLS0814080025 M8 14 x 100 25 16 80 130 13.4 25
SPS20/80 M12 20 x 60 15 21 80 100 19.4 25
SPS20/120 BLS1220080015 M12 20 x 105 15 21 80 130 26.5 10
SPS20/145 BLS1220080030 M12 20 x 105 30 21 80 145 29.5 10
SPS20/195 BLS1220150030 M12 20 x 175 30 21 150 215 43.5 10
SPS25/220 BLS1625150030 M16 25 x 185 30 26 150 220 70.0 10
SPS20/130SS** BLS1220080015A4 M12 20 x 105 15 21 80 130 26.5 10
Indent Products
BLS0814040015 M8 14 x 60 15 16 40 80 8.0 25
BLS1220150050 M12 20 x 175 50 21 150 235 46.0 10
BLS1625150040 M16 25 x 185 40 26 150 230 72.0 10
BLS1625150060 M16 25 x 185 60 26 150 250 76.0 10
BLS1625200040 M16 25 x 235 40 26 200 280 89.0 10
BLS1625200060 M16 25 x 235 60 26 200 300 95.0 10
**Stainless Steel anchor. Other anchors are available on request.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
74 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
superplus
Self-undercutting anchor
FASTENERS & TOOLS
The undercut fixing system that does not require
a special setting tool. Now with E-TAG approval
for use in Seismic areas.
Type BLS
Benefits:
l High capacity in cracked and non-cracked concrete
l High reliability due to undercut technology
l Simple installation, no special drill bit or setting tool required
l Applying torque creates undercut
l Two approved embedment depths per diameter
l Lower installed cost than traditional undercut anchors
l Reduced edge distances and spacings
75
FASTENERS & TOOLS
SAFETY BOLTS
SpaTec Plus Safety Anchors
Part No. Anchor Drill/Anch Min Hole Anchor Qty
Size or Dia. Depth Length (per box)
For techncial information on the loadings for all anchors, please refer to the Ramset Anchor Specification guide available
on the website or call your sales representative for a hard copy.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
76 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
DynaBolt™ Sleeve Anchors
DynaBolt Nut Head Anchors
Part No Drill/ Min Hole Anchor Qty
Anch Depth Length (per box)
or Dia.
Zinc
DP06026 6mm 20mm 26mm ea
DP06040 6mm 20mm 40mm ea
DP06060 6mm 20mm 60mm ea
DP08040 8mm 30mm 40mm ea
DP08065 8mm 30mm 65mm ea
DP08090 8mm 30mm 90mm ea
DP10040 10mm 35mm 40mm ea
DP10050 10mm 35mm 50mm ea
DP10075 10mm 35mm 75mm ea
DP10100 10mm 35mm 100mm ea
DP12060 12mm 40mm 60mm ea
DP12070 12mm 40mm 70mm ea
DP12100 12mm 40mm 100mm ea
DP12125 12mm 40mm 125mm ea
DP16065 16mm 55mm 65mm ea
DP16110 16mm 55mm 110mm ea
DP16140 16mm 55mm 140mm ea
DP20080 20mm 70mm 80mm ea
DP20115 20mm 70mm 115mm ea
DP20160 20mm 70mm 160mm ea
Galvanised
DP10050GH 10mm 35mm 50mm ea
DP10075GH 10mm 35mm 75mm ea
DP10100GH 10mm 35mm 100mm ea
DP12060GH 12mm 40mm 60mm ea
77
FASTENERS & TOOLS
Zinc
DP08045H 8mm 40mm 45mm ea
DP08070H 8mm 40mm 70mm ea
DP10055H 10mm 40mm 55mm ea
DP10080H 10mm 40mm 80mm ea
DP12065H 12mm 60mm 65mm ea
DP12075H 12mm 60mm 75mm ea
DP12105H 12mm 60mm 105mm ea
DP16070H 16mm 65mm 70mm ea
Stainless Steel 316
DP08070HSS 8mm 40mm 70mm ea
DP10080HSS 10mm 40mm 80mm ea
DP12075HSS 12mm 60mm 75mm ea
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
78 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
Screw-In Anchors
AnkaScrew Flanged Screw-In Anchor for Interior & Exterior Use
The Flanged AnkaScrew bolt has a washered head and comes hot dipped galvanised
for exterior use. Note that the head diameter is 19mm.
Concrete Nails
Part No. Description Nail Shank Qty
Length Diameter (per box)
79
FASTENERS & TOOLS
Zinc
T12080 12mm 48mm 80mm ea
T12100 12mm 48mm 100mm ea
T12120 12mm 48mm 120mm ea
T12140 12mm 48mm 140mm ea
T12180 12mm 48mm 180mm ea
T16100 16mm 64mm 100mm ea
T16125 16mm 64mm 125mm ea
T16150 16mm 64mm 150mm ea
T16175 16mm 64mm 175mm ea
T20120 20mm 80mm 120mm ea
T20160 20mm 80mm 160mm ea
Galvanised
T12080GH 12mm 48mm 80mm ea
T12100GH 12mm 48mm 100mm ea
T12140GH 12mm 48mm 140mm ea
T12180GH 12mm 48mm 180mm ea
T16100GH 16mm 64mm 100mm ea
T16125GH 16mm 64mm 125mm ea
T16175GH 16mm 64mm 175mm ea
T20120GH 20mm 80mm 120mm ea
T20160GH 20mm 80mm 160mm ea
T20215GH 20mm 80mm 215mm ea
Stainless Steel 316
T10075SS 10mm 40mm 75mm ea
T10090SS 10mm 40mm 90mm ea
T12080SS 12mm 48mm 80mm ea
T12100SS 12mm 48mm 100mm ea
T12140SS 12mm 48mm 140mm ea
T16100SS 16mm 64mm 100mm ea
T16125SS 16mm 64mm 125mm ea
T16175SS 16mm 64mm 175mm ea
T20120SS 20mm 80mm 120mm ea
T20160SS 20mm 80mm 160mm ea
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
80 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
81
FASTENERS & TOOLS
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
82 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
new
CRHR28 cordless rotary Fasteners & Tools
hammer drill
Powerful Ramset 28V cordless rotary hammer delivers corded tool
performance for a variety of concrete drilling applications.
83
FASTENERS & TOOLS
Accessories
Part No. To Suit Description Qty
Hole Size (per box)
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
84 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
Zinc
RTRM06L1 M6 1000mm ea
RTRM08L1 M8 1000mm ea
RTRM10L1 M10 1000mm ea
RTRM10L3 M10 3000mm ea
RTRM12L1 M12 1000mm ea
RTRM12L3 M12 3000mm ea
RTRM16L1 M16 1000mm ea
RTRM20L1 M20 1000mm ea
RTRM24L1 M24 1000mm ea
Galvanised
RTRM10L1GH M10 1000mm ea
RTRM12L1GH M12 1000mm ea
RTRM16L1GH M16 1000mm ea
RTRM20L1GH M20 1000mm ea
RTRM24L1GH M24 1000mm ea
AA316
RTRM06L1SS M6 1000mm ea
RTRM10L1SS M10 1000mm ea
RTRM12L1SS M12 1000mm ea
RTRM16L1SS M16 1000mm ea
RTRM20L1SS M20 1000mm ea
85
FASTENERS & TOOLS
Zinc
DSM06 M6 8mm 23mm 25mm 100
DSM08 M8 10mm 28mm 30mm 100
DSM10 M10 12mm 38mm 40mm 50
DSF10 M10 (Flanged) 12mm 28mm 30mm 50
DSM12 M12 16mm 48mm 50mm 50
DSM16 M16 20mm 63mm 65mm 25
DSM20 M20 24mm 78mm 80mm 25
Stainless Steel 316
DSM06SS M6 8mm 23mm 25mm 100
DSM08SS M8 10mm 28mm 30mm 50
DSM10SS M10 12mm 38mm 40mm 50
DSM12SS M12 16mm 48mm 50mm 50
DSM16SS M16 20mm 63mm 60mm 20
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
86 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
87
FASTENERS & TOOLS
Chemset A7 Ultra
Chemset A7 Ultra is an acrylic based adhesive used for high strength
applications. Suitable for colder environments, A7 Ultra is resistant to cyclic
loading and vibration. A7-10 dispenses using a standard caulking gun.
Part No. Cartridge Description Qty
Size (per box)
Epcon C6 Series
Epcon C6 is an epoxy mortar adhesive used for high strength applications.
This product is not suitable in cold conditions. Epcon C6 is resistant to cyclic
loading and vibration. Can also be used in underwater situations.
Part No. Cartridge Description Qty
Size (per box)
For technical information on cure times, loadings and installation instructions, refer to the Reid
website www.reids.co.nz.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
88 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
Extreme Performance Epoxy Resin
chemset c8rebarextreme
The Epcon C8 Extreme performance epoxy resin has been specifically
formulated for extreme and stud applications. With virtually no
new
smell Epcon C8 is easy to inject at low temperatures and is approved
Thefor use in C8
Chemset wetExtreme
and diamond drilled
performance holes.
epoxy resin has been specifically
NEW Epcon C8
formulated
This new formulation resin has no unpleasantWith
for extreme rebar and stud applications. virtually
odour makingno smell,
it ideal for
Chemset C8 is easy to
indoor applications. inject at low temperatures and is approved for use in wet
and diamond drilled holes. Suitable for indoor applications.
www.itwcp.co.uk
FIRE CSTB fire tested.
Freephone Orderline: 0800TESTED
833 381
8 Freephone Technical Helpline: 0800 731 4924
NF approved (6 months sustained load of
30KN in humid conditions with a maximum
displacement of 0.6mm).
89
www.itwcp.co.uk
FASTENERS & TOOLS
powder fixing
Spitfire Indirect Acting Tool
The Spitfire tool now has a new 75mm magazine
new 75mm MAGAZINE to
fire 75mm Pins
and is able to fire 75mm pins.
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
90 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
Grinding
Wet & dry cutting of hard
GC127TS
materials
91
FASTENERS & TOOLS
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
92 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
FASTENERS & TOOLS
93
FASTENERS & TOOLS
rm160 diamond drilling motor
FEATURES AND BENEFITS
Ph 0800 88 22 12 www.reids.co.nz
Range effective Jan 2012. ReidTM reserves the right to adjust range without notification. For more up-to-date details visit our website.
94 © Copyright Reid™ Construction Systems. All rights reserved. Version: 01/12/11. This supersedes all previous versions.
reid product literature
Reid supply a range of product literature to aid specification of our range of
products. Please contact us on info@reids.co.nz and request your copy now.
95
p: 0800 88 22 12
f: 0800 88 22 55
e: sales@reids.co.nz
contact details
Reid National Branches
Head Office Hamilton Tauranga - Mt Lower Hutt Christchurch
23-27 Poland Road, 21A Kaimiro Street, Maunganui 46 Victoria St, 7 O'Shannesey Place,
Glenfield Te Rapa Unit 1, 15 Portside Drive Alicetown Addington
p 0800 88 22 12 p 07 849 0643 p 07 575 7250 p 021 790 979 p 03 338 3844
f 0800 88 22 55 f 07 849 0642 f 07 575 7259 f 04 568 0098 f 03 338 8846
e sales@reids.co.nz e hamilton@reids.co.nz e tauranga@reids.co.nz e petez@reids.co.nz e christchurch@reids.co.nz