Professional Documents
Culture Documents
0
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 12/29/2018
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HVZ M16x125
Dynamic set or any suitable annular gap filling solution
Effective embedment depth: hef = 125 mm, hnom = 145 mm
Material: 8.8
Evaluation Service Report: Z-21.3-1692
Issued I Valid: 10/14/2016 | 4/14/2020
Proof: Design method DIBTDYN; dynamic load type:pulsating
Number of load cycles: > 1000000
Stand-off installation: bending not allowed; eb = 0 mm (no stand-off); t = 13 mm
Anchor plate: lx x ly x t = 250 mm x 250 mm x 13 mm; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, C20/25, fc,cube = 25.00 N/mm2; h = 230 mm
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
.
R
- The anchor calculation is based on a rigid baseplate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 12/29/2018
E-Mail:
Safety factors
gF,N gF,V
1.000 1.000
3 Tension load
Load [kN] Capacity [kN] Utilization bN [%] Status
Steel Strength* 15.260 19.259 801) OK
Pullout Strength* 15.260 22.222 69 OK
Concrete Breakout Strength** 15.260 22.361 69 OK
Splitting failure** N/A N/A N/A N/A
1
(gF,N · DNEd/DNRd)a; * anchor having the highest loading **anchor group (anchors in tension)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 12/29/2018
E-Mail:
4 Shear load
Load [kN] Capacity [kN] Utilization bV [%] Status
Steel Strength (without lever arm)* N/A N/A N/A N/A
Pryout Strength* N/A N/A N/A N/A
Concrete edge failure in direction ** N/A N/A N/A N/A
Concrete edge failure parallel in direction ** N/A N/A N/A N/A
1 a
(gF,V · DVEd/DVRd) ; * anchor having the highest loading **anchor group (relevant anchors)
concrete
bN,c bV,c+ bV,c- bV,cp Utilization bN,V [%] Status
Load case 34 0.682 - - - 57 OK
bNV = bN + bV
1.5 1.5
bN,c + (bV,c+ + bV,c- + bV,cp) ≤ 1.0
6 Loadcases - combinations
Loadcase No. Static Loads Dynamic loads
N Vx Vy Mz Mx My
34 + + 0 0 0 0 0
7 Displacements
In the cases of single-anchor and multiple-anchor fastenings, max. displacement of 1 mm must be expected over the entire range of use under
fatigue-relevant action (pure tensile and shear loading).
8 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This
means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate
thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid base plate assumption
is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for
plausibility!
• To install the anchor correctly the HILTI Dynamic Set is recommended
• Checking the transfer of loads into the base material is required in accordance with ETAG 001, Annex C(2010)Section 7! The software considers
that the grout is installed under the anchor plate without creating air voids and before application of the loads.
• The design method ETAG (filled holes) assumes that no hole clearance between the anchors and the fixture is present. This can be
achieved by
filling the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means
• The anchor resistances used for this design are ONLY valid if the Seismic set will be installed on the jobsite as per IFU when the Seismic washer
was selected.
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be
followed to ensure a proper installation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 12/29/2018
E-Mail:
9 Installation data
Anchor plate, steel: - Anchor type and diameter: HVZ M16x125
Profile: no profile Installation torque: 0.090 kNm
Hole diameter in the fixture: df = 18 mm Hole diameter in the base material: 18 mm
Plate thickness (input): 13 mm Hole depth in the base material: 145 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 190 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
125 125
125
125
1 x
125
125
125 125
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.in Profis Anchor 2.8.0
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 12/29/2018
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan