Professional Documents
Culture Documents
LOCTITE® 243
June-2004
m
Secondary Cure Activator
5m
m
m
Application Threadlocking
05
0.2
5m
0.
Strength Medium 50
0.1
LOCTITE® 243 is designed for the locking and sealing of
threaded fasteners which require normal disassembly with 25
standard hand tools. The product cures when confined in the
absence of air between close fitting metal surfaces and 0
prevents loosening and leakage from shock and vibration. 1min 5min 10min 30min 1h 3h 6h 24h 72h
Particularly suitable for applications on less active substrates Cure Time
such as stainless steel and plated surfaces, where Cure Speed vs. Temperature
disassembly with hand tools is required for servicing. The The rate of cure will depend on the temperature. The graph
thixotropic nature of LOCTITE® 243 reduces the migration of below shows the breakaway strength developed with time at
liquid product after application to the substrate. different temperatures on M10 steel nuts and bolts and tested
according to ISO 10964.
NSF International
Certified to ANSI/NSF Standard 61 for use in commercial and 100
% of Full Strength on Steel
5°C
40
75
ate
Brass
el
rom
Ste
ich
50
cd
Zin
Stainless Steel
25
0
1min 5min 10min 30min 1h 3h 6h 24h 72h
Cure Time
TDS LOCTITE® 243, June-2004
% RT Strength
10964.
100
% of Full Strength on Steel
50
75
25
or
at
c tiv
50 A
No Activator 7471 0
0 50 100 150
Activator 7649 Temperature, °C
25
Heat Aging
0 Aged at temperature indicated and tested @ 22 °C
1min 5min 10min 30min 1h 3h 6h 24h 72h
Cure Time 125
% Initial Strength at RT
100°C
TYPICAL PROPERTIES OF CURED MATERIAL 100
Physical Properties: 120°C
Coefficient of Thermal Expansion, ASTM D 696, K-1 80×10-6 75
Coefficient of Thermal Conductivity, ASTM C 177, 0.1
W/(m·K)
Specific Heat, kJ/(kg·K) 0.3 50
150°C
TYPICAL PERFORMANCE OF CURED MATERIAL 25
Adhesive Properties
0
After 24 hours @ 22 °C 0 1000 2000 3000 4000 5000
Breakaway Torque, ISO 10964: Hours
M10 steel nuts and bolts N·m 20
(lb.in.) (180) Chemical/Solvent Resistance
Prevail Torque, ISO 10964: Aged under conditions indicated and tested @ 22 °C.
M10 steel nuts and bolts N·m 7 % of initial strength
(lb.in.) (60) Environment °C 100 h 500 h 1000 h 5000 h
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m: Motor Oil 125 95 95 95 95
M10 steel nuts and bolts N·m 24 Gasoline 22 100 100 95 95
(lb.in.) (210) Brake fluid 22 100 100 100 100
Max. Prevail Torque, ISO 10964, Pre-torqued to 5 N·m: Water Glycol 50/50 87 95 80 80 80
M10 steel nuts and bolts N·m 24 Acetone 22 100 100 85 85
(lb.in.) (210) Ethanol 22 100 85 85 85
Compressive Shear Strength, ISO 10123:
Steel pins and collars N/mm² ≥7.6LMS GENERAL INFORMATION
(psi) (≥1,100) This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
TYPICAL ENVIRONMENTAL RESISTANCE a sealant for chlorine or other strong oxidizing materials.
Cured for 1 week @ 22 °C
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
M10 zinc phosphate steel nuts and bolts
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Henkel Loctite Americas Henkel Loctite Europe Henkel Loctite Asia Pacific
+860.571.5100 +49.89.9268.0 +81.45.758.1810
For the most direct access to local sales and technical support visit: www.loctite.com
TDS LOCTITE® 243, June-2004
Henkel Loctite Americas Henkel Loctite Europe Henkel Loctite Asia Pacific
+860.571.5100 +49.89.9268.0 +81.45.758.1810
For the most direct access to local sales and technical support visit: www.loctite.com