Professional Documents
Culture Documents
Manual Servicio WMA07DXESXS
Manual Servicio WMA07DXESXS
D ate
Product WMA07DXESXS
Any instructions in this service manual with this Warning sign must be followed strictly.
To prevent damage to the washing machine, any instructions in this manual with this
Stop sign must be followed strictly.
3
Issue
Service Manual Rev.
Order NO.TL1610S009
2-1 FEATURES
Soak wash make cleaner wash.
Fashionable appearance, transparent top lid
Efficaciously reduce noise
Self-adjustment to unbalance of laundry in spinning
Fuzzy computer control, self-program function, more
convenient washing
Unit:mm
4
Issue
Service Manual Rev.
Order NO.TL1610S009
2-2 SPECIFICATIONS
Model WMA07DXESXS
Free standing
Built under
EAN code
Energy efficiency class -
Start/Pause
Automatic balancing
Aesthetics
Cabinet material P=Plastic/Z=Zincking C
/C=Cold rolled stainless steel )
Adjustable feet
Technical data
Voltage/frequency V/Hz 220/60
Energy consumption kwh/kg
Water consumption L/kg 19
Wash power w 410
Spin power w 265
Special function
Air-Bubble
Feet wheel
Spray current
Dimensions (measurements)
Height mm 905
Width mm 520
Depth mm 560
5
Issue
Service Manual Rev.
Order NO.TL1610S009
Please plug the plug on special The power cord plug should be convenient
receptacle to be pluged in or pluged out with hand
with rated voltage. Be sure to use while the washing machine runs normally.
singlephase three pins receptacle. Be sure to pull the plug out and close the
Ensure the earthing prong of the power water tap when the machine is idle, when
receptacle is earthed reliably. Use moving the machine, or when cleaning the
leakage protector if possible. machine. Do not use wet hand to insert or
pull out the power plug.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have
it replaced by the technicians of our special shop or our customer care agent.
In case the washing machine is installed Do not use water hotter than 50 °C .
on ground with carpet, do not block the
ventilation hole with carpet.
The ventilation holes
at the bottom
Carpet
Do not put the machine at damp place like Do not wash water-proof laundries like
the bathroom. Never wash it with water. the raincoat, bike covers etc. to avoid
Not put wet laundries on the control panel. abnormal vibrations in spinning.
6
Issue
Service Manual Rev.
Order NO.TL1610S009
Do not stretch hands into the working Do not decompose, repair or alter the
machine. It is dangerous even if the machine by yourself.
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items (such Do not wash laundries with volatile
as the kettle with hot water ) on the materials (such as thinner, petrol etc.)
washing machine.
The children shall not approach Keep the machine away from direct
the working washing machine. sunlight and heat source like the heater.
Please check if the water faucet is open, and if the connection of the
water inlet pipe is proper.
It is suggested to use foamless washing powder.
Please don t use the washer in the environment below 0 C; if the washer
has been stored below 0 C, please be sure to ensure the washer is placed
under the room temperature more than 2 hours and then use otherwise
the washing ef f ects may be lowered or the washer may be damaged.
7
Issue
Service Manual Rev.
Order NO.TL1610S009
Screw
Front
Two fasteners
Back
The washing machine away from wall should be overrun 20mm. The largest
allowable slope of the shank base of the machine is 2 The slanting or rough
ground will result in unstable running or stoppage of the machine. Please adjust
it with following methods:
Confirm it's horizontal:
Hang the lead line to check if it is horizontal.
High low
Adjustable leg
8
Issue
Service Manual Rev.
Order NO.TL1610S009
Flashing
48 54 Normal
Deep
39 43 Hot Clean
Temp
Indicator display
Delay(Hours)
9
Issue
Service Manual Rev.
Order NO.TL1610S009
A “ Power ” button
Power
Power
Start
Power Pause
Start
B “ Pause
”button
After the power is switched on,press it to start the machine .
During working, push it to pause.
During pause,push it to restart and go on working.
C“ Cycle ” button
Program Application Program Application
Just run the washing cycle without
drainage cycle. The detergent clothing.
in the tub will be recycled.
Cycle
Remove detergent from the
For thick ,heay-soiled laundry.
clothes and then rinse with clean water.
Remove water when the wash program For clothing which requere careful
ends or when the clothes are still wet. handing and light-soiled
Water
D “ ” button
Water Temp
Temp
Water
the Hot,Warm or Cold temperature.
Temp
E “ ” button
During operation,the digtal indicator will display the remaining time (hours).
Push down the delay button. The delay indicator light is on ,the digtal indicator displays
the delay time of finishing washing (in hour).The point light flashs to indicate in the reverse
mode.
F“ ” button
load
4,6 or8.
6 8
10
Issue
Service Manual Rev.
Order NO.TL1610S009
11
Issue
Se r vice Manual
Rev.
Order NO.TL1610S009
or detergent box.
or detergent box.
Softener
Washing powder
12
Issue
Ser vice Manual
Rev.
Order NO.TL1610S009
Attention :
Do not lift the control panel seat by force ,otherwise the safety switch control rod may get
transformed.and the jointer part of the connecting pipe of the water level sensor may be
loosened ,therefore influence the normal operation of the microswitch and water level
sensor .
After opening the control panel seat ,hold it with one hand or lean it on supporter like the
wall .Do not put it down .
First loosen the screws when dismantling the computer controller .
3)Method cabinet and outer tub of disassembling
A.Loosen the two motor bolt unit to dismantle the motor.To adjust the
tension of the blet ,loosen the bolts and move the motor left and right .
B.Loosen the four fastening screws to dismantle the delivery shield .
C.Loosen the three fastening screws to dismantle the drain motor .
D.dismantle the drain pipe ,
E.In dismantling the inner tub ,first take off the outer tub cover ,then
dismantle the pulsator ,finally dismantle the inner tub .Handle with care
when taking the inner tub off from the outer tub .
13
Issue
Service Manual
Rev.
Order NO.TL1610S009
Drainage hose
Back cover
Drainconnector
14
Issue
Service Manual Rev.
Order NO.TL1610S009
15
Issue
Service Manual Rev.
Order NO.TL1610S009
Pull off No
the power exist
plug
16
Issue
Service Manual Rev.
Order NO.TL1610S009
There is no sound
There is no voltage
There is no voltage
17
Issue
Service Manual Rev.
Order NO.TL1610S009
No
18
Issue
Service Manual Rev.
Order NO.TL1610S009
Check the On/off point of No On/Off point Replace the microswitch or stop
the microswtich and stop switch.
switch.
Normal
Yes
At this time please check if the
Replace the retarder clutch.
drain motor is well.
Yes
If the hanger is wrong used? Replace the hanger is
No
Yes
If the noise of the motor Replace the motor
is too much?
No
No
If the motor is fastened tightly? Fasten the motor
Yes
If the balance ring is rubbing Yes Adjust the gap between the
the outer tub cover? balance ring and the outer tub.
No
19
Issue
Service Manual Rev.
Order NO.TL1610S009
No
No
If the motor fastened tightly? Fasten the motor.
Yes
Y Y
Adjust the paw spring Check if the paw
spring is unlocked
Measure Exist
N the voltage between the 1,2 Replace drain motor
terminals of the drain
motor
Adjust the Check if
connecting arm of
Y the two paws are Not exist
inserted into the two ratchet
the paw simultaneously
Measure
N the voltage between Exist
the purple and blue terminals of Replace the wire unit
the computer
sequencer
Adjust the retracting Y Check if the
spring retracting spring of the Not exist
retarder is loose
N
Replace the computer sequencer
Check if
the gap between At this time please confirm if the drain motor works normally
Adjust the Y the adjusting screw of the
adjusting screw of retarder brake lever and the baffle
the brake lever plate of the paw connecting
arm is too small
20
Issue
Se r vice Manual
Re v.
Order NO.TL1610S009
9. Brake time
6-2-10 out
Yes
Is the brake moment of the retarder Adjust the brake moment.
lower than 6N.m?
No
Yes
Is the reset spring of the retarder loose? Adjust the reset spring.
No
Is the gap between the connecting arm block Yes Check if the pawl can leave the ratchet for 2mm
and the brake arm of retarder less up during spinning. If not, adjust the position of
than 0.8mm?
the brake arm.
No
Replace the retarder.
21
Issue
Service Manual Rev.
Order NO.TL1610S009
Wiring Diagram
Fuse
Brown
Blue/White
Yellow
Yellow Door Switch
Yellow/Green
Cold Inlet Valve Grey
Orange
Water Level
Hot Inlet Valve Green/White
Orange Sensor
Blue Yellow
Drain Motor Red/White
White Balance Switch
Red/White
C
L Red
Motor
Blue
Black
Red/White
Red/White
Yellow
Red
Cabinet Retractor
motor White
Blue Blue
Blue
White
Black
22
MANUAL DESERVICIO | MODELO WMA07DXESXS