Professional Documents
Culture Documents
CODE: 00ZMXLC13/S4E
MODEL MX-LC13
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
When using this unit, check to confirm that there is any other indispensable option by referring to the configuration in the Service manual of the
machine.
Paper size/Kind/Weight
1-stage 2-stage
Min. weight 55g/m2 55g/m2
Max. weight 300g/m2 300g/m2
Paper type Thin paper Yes Yes
Standard paper Yes Yes
Recycled paper Yes Yes
Color paper Yes Yes
Letterhead Yes Yes
Printed paper Yes Yes
Punched paper Yes Yes
Thick paper 1 106 - 176g/m 2 Yes Yes
Thick paper 2 177 - 220g/m 2 Yes Yes
Thick paper 3 221 - 256g/m 2 Yes Yes
Thick paper 4 257 - 300g/m 2 Yes Yes
Embossed paper Yes Yes
Tab paper Yes Yes
OHP Yes Yes
Label sheet Yes Yes
Glossy paper Yes Yes
User type 1 - 9 Yes Yes
Paper size 12' x 18' (A3W ) 305 x 457 Yes Yes
Ledger (11' x 17' ) 279 x 432 Yes Yes
Ledger (11' x 17' ) Z-fold 279 x 216 No No
Legal (8.5' x 14' ) 216 x 356 Yes Yes
Legal (8.5' x 14' ) Z-fold 216 x 178 No No
Asian legal (8.5 x 13.5 ) 216 x 343 Yes Yes
Mexico legal (8.5' x 13.4' ) 216 x 340 Yes Yes
Foolscap (8.5' x 13' ) 216 x 330 Yes Yes
Letter (8.5' x 11' ) 279 x 216 Yes Yes
Letter R (8.5' x 11'R ) 216 x 279 Yes Yes
Letter R (8.5' x 11'R ) Z-fold 216 x 140 No No
Letter R (8.5' x 11'R ) 2-fold 216 x 140 No No
Letter R 3-fold/4-fold 216 x 93/70 No No
Invoice (5.5' x 8.5' ) *1 216 x 140 No No
Invoice R (5.5' x 8.5'R ) 140 x 216 No No
Executive R (7.25' x 10.5'R ) 184 x 266 Yes Yes
9 x 12 (A4W ) 305 x 229 Yes Yes
A3 297 x 420 Yes Yes
A3 Z-fold 297 x 210 No No
B4 257 x 364 Yes Yes
MX-LC13 SPECIFICATIONS 2 - 1
1-stage 2-stage
Paper size B4 Z-fold 257 x 182 No No
A4 297 x 210 Yes Yes
A4-R 210 x 297 Yes Yes
A4-R Z-fold 210 x 148 No No
A4R 2-fold, Z-fold 210 x 148 No No
A4-R 3-fold/4-fold 210 x 99/74 No No
B5 257 x 182 Yes Yes
B5-R 182 x 257 Yes Yes
A5 *1 210 x 148 No No
A5-R 148 x 210 No No
SRA3 320 x 450mm Yes Yes
SRA4 320 x 225mm Yes Yes
Kiku 8 318 x 234.75 Yes Yes
A8 312.5 x 220 Yes Yes
Kiku 4 318 x 469.5 Yes Yes
A4 312.5 x 440 Yes Yes
8K 270 x 390 Yes Yes
16K 270 x 195 Yes Yes
16K-R 195 x 270 Yes Yes
Monarch 98 x 191 No No
COM10 105 x 241 No No
DL 110 x 220 No No
C5 229 x 162 No No
Long No. 3 120 x 235 No No
Long No. 4 90 x 205 No No
Western No. 2 114 x 162 No No
Western No. 4 105 x 235 No No
Square No. 2 240 x 332 No No
Square No. 3 216 x 277 No No
Special - custom size Yes Yes
Custom range min X (Sub scanning) 182 182
max X (Sub scanning ) 457 457
min Y (Main scanning ) 182 182
max Y (Main scanning ) 320 320
Special - size undefined No No
Long scale paper Width: 90 - 305 No No
Length: 458 - 1200
MX-LC13 SPECIFICATIONS 2 - 2
TopPage
1 : ‘13/Dec
L1DFB01
L1DF101 L1DT103
L1 DA102
L1DT106
L1 DA101
L1DT110 1 1
L1DF001 L1DT115
L1DD005
L1DT105
L1DT104
L1DF002
L1DT114
L1DT112 L1DT113
L1DT205
L1DT204
L1DT214
L1DT212 L1DT213
L1DT207 L1DT211
2. Switch, Heater
L1HT101
L1DT102
L1DT101
L1DT116
L1DT108
L1WH1
.1WHSW
L1HT201
L1DT109
L1DT202
L1DD002 L1DT201
L1DT216
L1DT208
L1WH2
L1DT209
L1WH3
L1WH4
L1WH5
L1MT104
L1SL101 L1CL101
L1CL102
L1SL102 L1MT104
L1MT103
L1MT101
L1MT102 L1MT001
L1MT204
L1SL201 L1CL201
L1CL202
L1MT204
L1SL202
L1MT203
L1MT201
L1MT202
3
L1MT002
1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PS-187-2V
+24V 1
L1DT116 2
HRS HRS
L1DT116
L1DT115
DF11-6DS-2C DF11-6DS-2C
+DF11-6DP-SP1(05) +DF11-6DP-SP1(05)
1
L1 DA001/
L1 DA002
+5V GND
6 5 4 3 2 1 6 5 4 3 2 1
SMP-18V-NC SMR-18V-N
L1DT106
ELR-03V ELP-03V
L1MT101-D 1 1 1 1
L1MT101-U 3 3 2 2 CN-I B28B-PHDSS-B
3 3 3 +24V_PS2
PS-187-3V 4 4 4 L1DT108_R
+24V 1 5 5 5 L1MT101-D
L1DT108 3 6 6 6 L1DD002_R
L1DT107
7 7 7 L1DT116_R
L1DT113
8 8 10 +24V_PS2
L1DT104
PHR-3 9 9 11 L1DT101_R
+5VR 1 10 10 14 L1MT101-U
L1DT114
L1DT111
GND 2 11 11 15 +5VR
L1DT107 3 12 12 17 L1DT107
13 13 20 L1DT104
L1MT101
+5V 1 1 15 15 22 L1MT104_1
GND 2 2 16 16 23 P_GND
L1DT112
L1DT104 3 3 17 17 25 L1DT110
18 18 28 L1DA104
3 +5VR
179228-3
4 L1LD101
+5V 1
5 L1DT109
L1DT112 2
8 L1DT105
GND 3
10 +24V_F5
11 L1SL102-U
179228-3
12 L1SL102-L
+5V 1
13 +24V
L1DT113 2
14 L1MT104_2
GND 3
15 P_GND
L1DT105
17 L1DT106
179228-3
18 +5V
+5V 1
L1SL102
L1DT114 2
GND 3
Electrical and mechanism relation diagram
SMP-10V-NC SMR-10V-N
[4] OPERATIONAL DESCRIPTIONS
BU10P-TR-P-H 1 1
PHR-4 SMR-04V-N SMP-04V-NC PHNR-10-H PHNR-10-H 2 2
+5VR 1 1 1 1 10 3 3
L1WH1
L1LD101 2 2 2 2 9 4 4
L1DT109
L1DT109 3 3 3 3 8 5 5
GND 4 4 4 4 7 6 6
5 6 7 7
179228-3 6 5 8 8
+5V 1 7 4 9 9
L1DT110 2 8 3 10 10
GND 3 9 2
L1MT104
+5V 1 1 1 1 1
RELAY PWB
+24V_F5 11
L1DT106 2 2 2 2 2
L1PW001 10
GND 3 3 3 3 3
GND 9
4 4
L1HT201 8
179228-3 5 5
GND 7
+5V 1 6 6
L1HT101 6
L1DT111 2 CN-B B14B-PHDSS-B
L1DT116_R 5
GND 3
ELR-02V ELP-02V CN-D B2P3-VH-R P GND 4 14 L1DT216_R
1 1 1 KWL_3 /HL PR1 3 13 L1DT116_R
2 2 2 N.C. L1DT216_R 2 12 GND
179228-3 3 KWN_3 /HL PR2 1 11 P_GND
+5V 1 10 /HL_PR2
1 HRS 9 /HL_PR1
L1DT115 2
2 DF11-4DS-2C
: ‘13/Dec
8 L1PW001
+5V
GND 3
3 +DF11-4DP-SP1(05) 7 +24V_F5
4 6 L1HT201
1
5 L1HT101
1 HRS
2 DF11-4DS-2C
+5V
3 +DF11-4DP-SP1(05)
4
TopPage
1 HRS
DF11-4DS-2C
GND
2
1
3 +DF11-4DP-SP1(05)
4
1
1.
TopPage
1 : ‘13/Dec
PS-187-2V
+24V 1
L1DT215
L1DT216 2
HRS HRS
L1DT216
DF11-6DS-2C DF11-6DS-2C
+DF11-6DP-SP1(05) +DF11-6DP-SP1(05)
1
+5V GND
6 5 4 3 2 1 6 5 4 3 2 1
L1DT206
7 7 7 L1DT216_R
L1WH5
L1DT213
8 8 10 +24V_PS1
L1DT204
PHR-3 9 9 11 L1DT201_R
+5VR 1 10 10 14 L1MT201-U
L1DT214
GND 2 11 11 15 +5VR
L1DT211
L1DT207 3 12 12 17 L1DT207
13 13 20 L1DT204
L1MT201
+5V 1 1 15 15 22 L1MT204_1
GND 2 2 16 16 23 P_GND
L1DT212
L1DT204 3 3 17 17 25 L1DT210
18 18 28 L1DA204
SMP-03V-NC SMR-03V-N
+24V 1 1
CN-P B22B-PHDSS-B
L1MT204_1 2 2
1 GND
P_GND 3 3
2 L1DA203
L1DT208
3 +5VR
179228-3
L1WH4
L1DT213 2
14 L1MT204_2
GND 3
15 P_GND
L1DT205
17 L1DT206
179228-3
18 +5V
+5V 1
L1SL202 L1DT214 2
GND 3
L1WH3
+5V GND
6 5 4 3 2 1 6 5 4 3 2 1
L1DT210
SMP-10V-NC SMR-10V-N
BU10P-TR-P-H 1 1
PHR-4 PHNR-10-H PHNR-10-H 2 2
+5VR 1 1 1 1 10 3 3
L1WH2
LTLD201 2 2 2 2 9 4 4
L1DT209
L1DT209 3 3 3 3 8 5 5
GND 4 4 4 4 7 6 6
SMR-04V-N SMP-04V-NC 5 6 7 7
179228-3 6 5 8 8
+5V 1 7 4 9 9
L1DT210 2 8 3 10 10
3 9 2
L1MT204
GND3
BU16P-TR-P-H 10 1 CN-O B36B-PNDZS-1
179228-3 PHNR-16-H PHNR-16-H 3 GND
+5V 1 1 16 7 +5V
L1DT205 2 2 15 BU12P-TR-P-H 11 L1DT212
GND 3 3 14 PHNR-12-H PHNR-12-H 12 GND
4 13 1 12 13 L1DT213
5 12 2 11 15 L1DT214
6 11 3 10 SMP-07V-NC SMR-07V-N 17 L1DT215
SMR-03V-N SMP-03V-NC 7 10 4 9 1 1 20 +5V
+24V 1 1 8 9 5 8 2 2 26 L1DT211
L1SL202-U 2 2 9 8 6 7 3 3
L1SL202-L 3 3 10 7 7 6 4 4
11 6 8 5 5 5
SMP-03V-NC SMR-03V-N 12 5 9 4 6 6
+24V 1 1 13 4 10 3 7 7
L1MT204_2 2 2 14 3 11 2
P_GND 3 3 15 2 12 1
16 1
179228-3 SMR-03V-N SMP-03V-NC SMP-06V-NC ELR-02V ELP-02V
CN-A B11B-PASK-1
B. Paper feed tray (2CS)
+5V 1 1 1 1 1 1 1
RELAY PWB
2 2 +24V_F5 11
L1DT206 2 2 2 2 2
L1PW001 10
GND 3 3 3 3 3 ELR-02V ELP-02V GND 9
4 4 1 1
CN-E B4P(5-3)-VH L1HT201 8
179228-3 5 5 2 2
1 KWL_1 GND 7
+5V 1 6 6
ELR-02V ELP-02V 2 KWL_2 L1HT101 6
L1DT211 2 SMR-06V-N CN-B B14B-PHDSS-B
1 1 3 N.C. L1DT116_R 5
GND 3
ELR-02V 2 2 4 KWN_1 P GND 4 14 L1DT216_R
5 KWN_2 /HL PR1 3 13 L1DT116_R
ELR-02V ELP-02V L1DT216_R 2 12 GND
1 1 /HL PR2 1 11 P_GND
2 2 10 /HL_PR2
: ‘13/Dec
+5V
L1DT215 2 3 +DF11-4DP-SP1(05) 7 +24V_F5
GND 3 4 6 L1HT201
5 L1HT101
1 HRS
1
2 DF11-4DS-2C
+5V
3 +DF11-4DP-SP1(05)
TopPage
4
1 HRS
DF11-4DS-2C
GND
2
1
1
3 +DF11-4DP-SP1(05)
4
TopPage
1 : ‘13/Dec
SMP-08V-NC SMR-08V-N
L1CL201
L1CL101
L1DT102_R 1 1
2 2
179228-3 3 3
+5V 1 4 4
L1DT103 2 5 5
GND 3 6 6
7 7
SMR-03V-N SMP-03V-NC 8 8
+24V 1 1
L1SL101 3 3
SMR-02V-NSMP-02N-NC SMP-06V-NCSMR-06V-N
L1DA102 1 1 1 1
GND 2 2 2 2
3 3
SMR-04V-N SMP-04V-NC 4 4
1 1 5 5
2 2 6 6
L1MT202
3 3
4 4
L1MT102
1 1 1 1 HRL1
L1SL201
L1MT102-24V 1 1 18 L1MT102-24V
L1SL101
L1MT102 2 2 19 L1MT102
P_GND 3 3 20 L1MT102-T
L1MT203 L1MT102-T 44 21
22
L1MT103-24V
L1MT103
SMR-04V-N SMP-04V-NC 23 L1MT103-T
L1MT103-24V 1 1 31 L1DO101
L1MT103 2 2 36 L1DA101
P_GND 3 3 37 GND
L1MT103-T 4 4 38 L1DA102
39 GND
PS-187
+24V
L1DT102
SMP-08V-NC SMR-08V-N
2
2
L1DT202_R 1 1
2 2
179228-3 3 3
L1DT202
L1DT103
GND 3 6 6
L1HT201
7 7
L1HT101
L1DT203
SMR-03V-N SMP-03V-NC 8 8
+24V 1 1
L1SL201 3 3
SMR-02V-N SMP-02V-NC SMP-06V-NC SMR-06V-N
L1DA202 1 1 1 1
GND 2 2 2 2
L1DA101
L1DA201
3 3
SMR-04V-N SMP-04V-NC 4 4
1 1 5 5
1
1
2 2 6 6
3 3
4 4
ELP-03V ELR-03V ELR-03V ELP-03V
1 1 1 1 HRL2
2 2 2 2
CN-R B40B-PNDZS-1
3 3 3 3 HRN2 1 L1DT201_R
2 L1DT202_R
BU02P-TR-P-H 3 P_GND
PHNR-02-H PHNR-02-H 4 P_GND
3
+2 4 V 2 1 7 L1DD002_R_F1
L1DA102
L1DA202
L1CL201 1 2 8 L1CL201
9 L1DD002_R_F1
10 L1SL201
13 +5V
C. Paper feed unit
14 GND
15 L1DT203
SMR-04V-N SMP-04V-NC 16 GND
L1MT202-24V 1 1 18 L1MT202-24V
L1MT202 2 2 19 L1MT202
P_GND 3 3 20 L1MT202-T
L1MT202-T 4 4 21 L1MT203-24V
22 L1MT203
SMR-04V-N SMP-04V-NC 23 L1MT203-T
L1MT203-24V 1 1 31 L1DO201
L1MT203 2 2 36 L1DA201
P_GND 3 3 37 GND
L1MT203-T 4 4 38 L1DA202
39 GND
40 GND
Signal name Name Function/Operation
L1CL101 1CS paper feed clutch Controls ON/OFF of the 1CS paper feed belt.
L1CL201 2CS paper feed clutch Controls ON/OFF of the 2CS paper feed belt.
L1DA101 1CS hot-air heater temperature sensor Detects the temperature in the hot-air heater.
L1DA102 1CS temperature sensor Detects the temperature in the 1CS paper feed duct.
L1DA201 2CS hot-air heater temperature sensor Detects the temperature in the hot-air heater.
L1DA202 2CS temperature sensor Detects the temperature in the 2CS paper feed duct.
L1DT102 1CS upper limit switch Prevents the tray from lifting extraordinarily to break the paper feed unit.
L1DT103 1CS paper sensor Detects 1CS paper.
L1DT202 2CS upper limit switch Prevents the tray from lifting extraordinarily to break the paper feed unit.
L1DT203 2CS paper sensor Detects 2CS paper.
L1HT101 1CS hot-air heater Makes paper feed air hot.
L1HT201 2CS hot-air heater Makes paper feed air hot.
L1MT001 Transport motor 1 Drives the paper feed and the transport section.
L1MT102 1CS suction fan Sucks the paper feed unit.
L1MT103 1CS exhaust fan Blows to the paper feed section.
L1MT202 2CS suction fan Blows to the paper feed unit.
L1MT203 2CS exhaust fan Blows to the paper feed section.
L1SL101 1CS suction valve solenoid Controls ON/OFF of suction air.
L1SL201 2CS suction valve solenoid Controls ON/OFF of suction air.
+5V 19 25 25 4 4 2 L1DD005
L1DF003 20 26 26 5 5 179228-3 3 GND
GND 21 27 27 6 6 1 +5V
+5V 22 28 28 2 L1DD003
L1DF004 23 29 29 3 GND
GND 24 30 30
+5V 25 31 31
L1DF005 26 32 32
L1DD003
GND 27 33 33
+5V 28 34 34
12
L1DF010 29 35 35
GND 30 36 36
37 37
38 38
L1DD005
11
39 39
40 40
L1DF005
13 14
6
10
17
9
16
L1DF004
L1DFB01
L1DF201
18
L1DF003
8
7
5
3 3 3 GND
L1DF001
L1DF002
L1DF010
SMP-03V-NC SMR-03V-N 179228-3
L1DF101
1 1 1 +5V
15
2 2 2 L1DF010
2
3 3 3 GND
1
7 L1MT001-T
BU02P-TR-P-H
CN-R B40B-PNDZS-1 PHNR-02-H PHNR-02-H
L1DD002_R_F4 5 1 2 +24V
L1CL202 6 2 1 L1CL202
L1MT001
BU02P-TR-P-H
CN-H B40B-PNDZS-1 PHNR-02-H PHNR-02-H
L1DD002_R_F4 5 1 2 +24V
L1CL102
L1CL102 6 2 1 L1CL102
Signal name Name Function/Operation
L1CL102 1CS transport clutch Controls ON/OFF of the 1CS transport roller.
L1CL202 2CS transport clutch Controls ON/OFF of the 2CS transport roller.
L1DD003 Transport open/close sensor 1 Detects open/close of the transport paper guide.
L1DD004 Transport open/close sensor 2 Detects open/close of the transport paper guide.
L1DD005 Vertical transport open/close sensor Detects open/close of the vertical transport paper guide.
L1DF001 Vertical transport sensor 1 Detects transport of paper.
L1DF002 Vertical transport sensor 2 Detects transport of paper.
L1DF003 Vertical transport sensor 3 Detects transport of paper.
L1DF004 Vertical transport sensor 4 Detects transport of paper.
L1DF005 LCT paper exit sensor Detects transport of paper.
L1DF010 Horizontal transport sensor 5 Detects transport of paper.
L1DF101 1CS paper exit sensor Detects transport of paper.
L1DF201 2CS paper exit sensor Detects transport of paper.
L1DFB01 Manual feed paper entry sensor Detects transport of paper.
L1MT001 Transport motor 1 Drives the paper feed and the transport section.
3
1
2
2
3
1
2
2
MX-LC13 MAINTENANCE 5 - 1
2. Transport section
: Check (Clean, replace, or adjust according to necessity.) : Clean : Replace : Adjust : Lubricate
When Every
Unit No. Maintenance part Remarks
calling 300K
Vertical transport unit 1 Transport roller 1 Clean with a water dampened cloth.
2 Transport roller 2
3 Transport roller 3
4 Transport roller 4
5 Transport roller 5
6 Transport roller 6
7 Transport roller 7
8 Transport roller 8
9 Transport roller 9
10 Belts ---
11 Sensors
--- Transport paper guides
11
3
1
10
10
4
11
5 10
11
8
7
11
11
2
11
9
6
10
MX-LC13 MAINTENANCE 5 - 2
3. Drive section
: Check (Clean, replace, or adjust according to necessity.) : Clean : Replace : Adjust : Lubricate
When Every
Unit No. Maintenance part Remarks
calling 300K
Upper paper feed drive unit 1 Belts ---
Main drive unit 2 Belts ---
Lower paper feed drive unit 3 Belts ---
MX-LC13 MAINTENANCE 5 - 3
[6] DISASSEMBLY AND ASSEMBLY
1. Each unit disassembly 2) Remove the screw, and remove the right cabinet.
A. Exterior section
No. Unit name
1 Rear cabinet
1
2 Right cabinet
3 Upper cabinet left
4 Left front cabinet 1
2
5 Left rear cabinet
1
3
1
1
1
4
2
1
3
3
4
1
3
2) Remove the cap. Remove the screw, and remove the upper
cabinet left.
3 1
2
2
1
2
(2) Right cabinet
1) Remove the screw, and remove the right cabinet lower cover.
3
2
2
1
2
1
2
3) Remove the resin E-ring, and remove the shaft. Remove the
left door. (1) Paper feed tray
1) Remove the right cabinet.
2) While releasing lock of the paper feed tray bottom, pull out the
paper feed tray.
2
2
3
1
2
1
3) Remove the screws at the back side of the paper feed tray,
and remove the binding band and the earth wire.
(5) Left rear cabinet Disconnect the connector.
1) Remove the rear cabinet.
2) Remove the screw, and remove the left rear cabinet
3
1
2
1
1
2 1
2
1
2 1
1
(3) Paper feed belt 2
1) Remove two screws from the suction duct front frame/top side
of the Unit.
2 2) Turn the unit over and remove two screws from the blower
3
duct; rear side/bottom of the unit.
2
2) While releasing lock of the paper feed tray bottom, pull out the
paper feed tray.
3) Disconnect 3 connectors and remove the band.
1
2
*When installing the unit, make sure not to drop and lose the %
grounding plate. Put it aside for later installation.
NOTE: Never insert the belts horizontally by force, in order not
6) Before moving the Follower roller shaft, make sure that you to transform the belts.
pull the solenoid arm out of the slot.
8QLW)6LGH
7) Lift and move the follower roller shaft to the center of the unit to
release the tension on the belt. And then remove the E-clips of 8QLW)6LGH
the both side of the follower shaft..
(4) Paper feed duct unit
1) Remove the rear cabinet.
2) Disconnect the connector of the fan and clutch. Remove the
screw, and remove the binding band.
1
1
8) Remove the bearings of the both side and remove the follower
roller shaft out of the slot to allow the belt to slide out. 2
3
1
1
3) Remove the screw, and remove the paper feed duct unit.
1 1
1
1
1
2
1
5
2
4
1 2
2
1
1
2 3
7) Remove the E-ring, and remove the knob. Remove the screws
and remove the inside cabinet left lower.
1
2 4
3
1
2
1
2 2
3
2
1
1 2
2
1
3
2
1
2 2
1
1
E. PWB section
No. Unit name 1
1 Main PWB
2 DC power PWB 2 2
3 Heater relay PWB
4 AC PWB
(3) Heater relay PWB
1) Disconnect the connector from the heater relay PWB. Remove
the screw and the supporter, and remove the heater relay
PWB.
2 2
1 1
3 3
1
4 1 4
2
2
3
2
1 1
2 1 2 1 2 3
2
1 2
4
1 2
1 1
1
3 3
2
2
1 1
2 1 2 1 2
B. Transport section
2) Open the paper guide.
(1) Vertical transport unit Clean the transport roller 7 and the transport roller 8.
a. Transport roller 3, Transport roller 4, Transport roller 5,
Transport roller 6
1) Open the left door.
c. Transport roller 2
1) Open the left door.
Blowing pressure
measuring side: Red
Suction side
The table below shows the specified ranges at the measuring
points of air pressure.
LCT cassette 1 LCT cassette 2
Suction duct*1 A 130 - 230 C 130 - 230
Blowing duct B 310 - 410 D 310 - 410
Simulation No. Sim4-3 Sim4-3
Unit (Pa)
*1 : The air pressure of the suction duct must be measures with
paper attached to the paper feed belt.
When the measured value of the air pressure is outside the speci-
fied range, check the following items.
• Does the blower fan rotate?
• Are the valves opened and closed smoothly?
• Is the connector to the rear frame connected securely?
• Is the solenoid installed to the proper position? (Does it operate
smoothly?)
• Are the duct body, the suction duct and the blowing duct not bro-
ken?
• Are the duct body, the suction duct, the blowing duct, the blower
fan, and the duct joint tightened by screws firmly?
• Is there no air leak in the sound-muffling duct, between the
blower fan, and in the duct joint?
MX-LC13 ADJUSTMENT 7 - 1
Blowing side Blowing side
6) When the air pressure is in the specified range, cancel the pro-
5) Insert a tube into the measuring point to measure. (For an gram with “EXECUTE.”
actual measuring, attach the toll to the machine.)
7) When the air pressure is outside the specified range, adjust in the
Check to confirm that the tube is securely inserted, and then
following procedures.
measure.
When the values of “B VACUUM FAN DUTY(PLAIN-M)” and “T
Suction side BLOWER FAN DUTY (PLAIN-M)” in Sim4-11 are changed, they
are reflected to the measured value of the above Sim4-3.
By increasing the vacuum fan duty and the blower fan duty values
in the simulation, the suction pressure is increased.
(The vacuum fan duty and the blower fan duty values must be
changed to the same value. Example: When B is 60, make T 60.)
Since the blowing pressure is also increased, be sure to check
the blowing pressure after adjustment of the suction pressure.
By decreasing the vacuum fan duty and the blower fan duty val-
ues in the simulation, the suction pressure is decreased.
(The vacuum fan duty and the blower fan duty values must be
changed to the same value. Example: When B is 40, make T 40.)
Since the blowing pressure is also decreased, be sure to check
the blowing pressure after adjustment of the suction pressure.
NOTE: Though the duty setting in Sim4-11 can be changed
according to the size and the paper type, it is not
reflected to the measured value of the above Sim4-3.
Note that carefully.
MX-LC13 ADJUSTMENT 7 - 2
TopPage
1 : ‘13/Dec
Communication Communication
Communication circuit with main unit (main unit connection cable) circuit with 5V
circuit with LCT
main unit
5V CPU
24V
Communication
circuit with
second series
LDSW_R_F4
Interface unit transport clutch
䠄24V䠅
Clock
24V Spectrum
diffusion circuit Tray lift motor
control circuit
Solenoid/clutch
drive circuit
Assist fan
motor 2
LDSW_R_F4
䠄24V䠅
Assist fan motor
drive circuit
Lift motor
Vertical transport UN
Manual feed paper entry sensor
OUT1 Lift motor Vertical transport sensor 3
Tray SW PWB Vertical transport sensor 2
5V drive circuit
OUT2 Vertical transport sensor 1
SW 1CS paper exit sensor
LED 1CS descending side power Vertical transport open/close
+24V_F5 F5 sensor
Tray lock/ 24V 2CS descending side power
lock release SOL
Horizontal transport sensor 5
1CS lifting side power
Tray lock sensor 5V Vertical transport sensor 4
2CS paper exit sensor
2CS lifting side power
LCT paper exit sensor
LDSW_R_F4 Transport open/close sensor 2
Transport open/close sensor 1
䠄24V䠅 LCT machine connection detection
Sensor input
circuit F4
1CS transport clutch
2CS transport clutch
S_GND F6 24V
Power unit
Refer to the block diagram 㻞㻠䠲 cooling fan
of the primary side of motor
AC, the heater From DC power unit P_GND
relay and the 24V
12V
DC power section.
Transport motor Transport
S_GND control circuit motor
3.3V
FW
L1HT10䋱 L1HT201
CN 䌁
CN D 1 /HLPR2 L1D䌔216_R(24V)
L1HT201
ELP-03V ELR-03V ELR-03V ELP-03V
1 1 1 1 HRL2
2 2 2 2
3 3 3 3
CN-R B40B-PNDZS-1 L1DT201_R
HRN2 1 L1DT201_R
2 L1DT202_R
3 P_GND
4 P_GND L1DD002_R_F4
5 L1DD002_R_F4
6 L1CL202 L1DD002_R_F1
7 L1DD002_R_F1
8 L1CL201
9 L1DD002_R_F1
10 L1SL201
BU02P-TR-P-H
11 P_GND
PHNR-02-H PHNR-02-H
12 P_GND
+24V 2 1
L1CL202 13 +5V
L1CL202 1 2
14 GND
BU02P-TR-P-H 15 L1DT203
PHNR-02-H PHNR-02-H 16 GND
+2 4 V 2 1 17 GND
L1CL201
L1CL201 1 2 18 L1MT202-24V
19 L1MT202
20 L1MT202-T
SMR-04V-N SMP-04V-NC
21 L1MT203-24V
L1MT202-24V 1 1
22 L1MT203
L1MT202 2 2
L1MT202 23 L1MT203-T
P_GND 3 3
24 YOBI6
L1MT202-T 4 4
25 YOBI7
26 YOBI8
SMR-04V-N SMP-04V-NC 27 YOBI9
L1MT203-24V 1 1 28 +24V
L1MT203 2 2 29 L1MT205
L1MT203
P_GND 3 3 30 L1MT205-T
L1MT203-T 4 4 31 L1DO201
32 +5V
33 L1DA207+
34 GND
35 GND
36 L1DA201
37 GND
38 L1DA202
39 GND
40 GND
3-292254-1(BLUE)(AMP) BU11P-TZ-S
3-179228-1(BLUE) 3-179228-1(BLUE) CZHR-11V-S CZHR-11V-S CN-E B24B-PHDSS-B
11 1 11 1 1 L1MSLIDE
10 2 10 2 2 L1MLED
9 3 9 3 3 L1MLSW
8 4 8 4 4 L1MPRM-D
7 5 7 5 5 L1MPRM-U
6 6 6 6 6 L1MPUS
5 7 5 7 7 L1MREVM-CLK
4 8 4 8 8 L1MREVM-MODE3
3 9 3 9 9 L1MPUM-CLK
2 10 2 10 10 L1MPUM-MODE3
1 11 1 11 11 L1MPUM-RSET
12 M1MLLS
13 L1MPES
1-292254-2(AMP) BU12P-TZ-S
14 L1MSIZ5
1-179228-2 1-179228-2 CZHR-12V-S CZHR-12V-S
15 L1MSIZ4
12 1 12 1
16 L1MSIZ3
11 2 11 2
17 L1MSIZ2
10 3 10 3
18 L1MSIZ1
9 4 9 4
19 L1MPVS2
8 5 8 5
20 L1MPVS1
7 6 7 6
21 L1MPFS
6 7 6 7
22 L1MLS
5 8 5 8
23 L1MULS
4 9 4 9
24 GND
3 10 3 10
2 11 2 11
1 12 1 12
LCT MAIN PWB
DC POWER UN
CN-A B8P-VH
CN-101 B8P-VH-B
+5V 1
1 +24V
GND
+24V
2
3 CN-102 B7P-VH-B 200V Series only
P_GND 4 1 P_GND
+12V 5
CN-103 B5P-VH-B CN-4 B2P3-VH-B-E(BL) ELP-02V ELR-02V
GND 6
1 +12V LiveR out 1 1 1
+3.3V 7 Reactor
4 GND N.C. 2 2 2
GND 8
LiveR in 3
CN-104 B9P-VH-B
2 GND
5 +5V
CN-105 B4P-VH-B CN-1 B03P-VL-R(RD)
1 +3.3V AC-L(IN) 1
4 GND N.C. 2
AC-N(IN) 3
CN-B B14B-PHDSS-B CN-3 B04B-PASK-1
FW 1 4 FW
P_GND 2
L1MT002(+24V) 3 Dehumidifying heater switch
L1MT002-T 4 SMP-03V-NC SMR-03V-N PS-187
L1HT101 5 1 1 L1MT002(+24V)
+24V_F5 L1HT201 6 2 2 P GNDL1MT002 L1MT002 PS-187
+24V_F5 7 3 3 L1MT002-T
L1PW001 8
/HL_PR1 9
/HL_PR2
P_GND
10
11
CN-A
1
B11B-PASK-1
/HL PR2 RELAY PWB AC PWB
L1DT116_R GND 12 2 L1DT216_R CN-5
L1DT116_R 13 3 /HL PR1 CN-H B03P-VL CN-2 B03P-VL-K(BK) B03P-VL-E(BL)
L1DT216_R 14 4 P GND AC-L(IN) 1 1 AC-N(OUT) AC-L(OUT) 1
L1DT216_R 5 L1DT116_R N.C. 2 2 N.C. N.C. 2
6 L1HT101 AC-N(IN) 3 3 AC-L(OUT) AC-N(OUT) 3
7 GND
8 L1HT201
9 GND
CN-I B03P-VL-K(BK) CN-3 B03P-VL-R(RD)
10 L1PW001
AC-L(OUT) 1 1 AC-L(IN)
11 +24V_F5
N.C. 2 2 N.C.
AC-N(OUT) 3 3 AC-N(IN)
CN-B B3B-PH-K-S
1 +24V_RY
2 N.C.
3 GND_RY
CN-F B2P3-VH CN-6 B2P3-VH-RD CN-1 B03P-VL(WH)
CN-CB4B-PH-K-S AC-L_H(IN) 1 1 AC-N_H(OUT) AC-L(IN) 1
+24V_RY 1 +24V_RY N.C. 2 2 N.C. N.C. 2
GND_RY 2 N.C. AC-N_H(IN) 3 3 AC-L_H(OUT) AC-N(IN) 3
3 GND_RY
4 N.C.
CN-E B4P(5-3)-VH
CN-JB03P-VL-E(BL) KWL_1 1
HRL1 1 HRL1 KWL_2 2
L L
HRN1 2 N.C. N.C. 3
FG FG
3 HRL2 KWN_1 4
N N
KWN_2 5
HRL2 CN-G B03P-VL-R(RD)
HRN2 1 HRN2 CN-D B2P3-VH-R
2 N.C. KWL_3 1
3 HRN1 N.C. 2 ELP-02V ELR-02V
KWN_3 3 1 1
Dehumidifying heater 3
2 2
L1HT101
ELP-03V ELR-03V ELR-03V ELP-03V
1 1 1 1 HRL1
2 2 2 2
CN-H B40B-PNDZS-1 L1DT101_R
3 3 3 3 HRN1 1 L1DT101_R
2 L1DT102_R
3 P_GND
4 P_GND L1DD002_R_F4
5 L1DD002_R_F4
6 L1CL102 L1DD002_R_F1
7 L1DD002_R_F1
8 L1CL101
9 L1DD002_R_F1
10 L1SL101
BU02P-TR-P-H
11 P_GND
PHNR-02-H PHNR-02-H
12 P_GND
+24V 2 1
L1CL102 13 +5V
L1CL102 1 2
14 GND
BU02P-TR-P-H 15 L1DT103
PHNR-02-H PHNR-02-H 16 GND
+2 4 V 2 1 17 GND
L1CL101
L1CL101 1 2 18 L1MT102-24V
19 L1MT102
20 L1MT102-T
SMR-04V-N SMP-04V-NC
21 L1MT103-24V
L1MT102-24V 1 1
22 L1MT103
L1MT102 2 2
L1MT102 23 L1MT103-T
P_GND 3 3
24 +24V
L1MT102-T 44
25 L1MT003-CLK
26 L1MT003
SMR-04V-N SMP-04V-NC 27 L1MT003-T
L1MT103-24V 1 1 28 +24V
L1MT103 2 2 29 L1MT105
L1MT103
P_GND 3 3 30 L1MT105-T
L1MT103-T 4 4 31 L1DO101
32 +5V
33 L1DA107+
34 GND
35 GND
36 L1DA101
37 GND
38 L1DA102
39 GND
40 GND
2 connection LCT
ELP-15V ELR-15V
1 1 N.C. CN-N B12B-PASK-1
2 2 L1DO005 1 L1DO005(GND)
3 3 TXD-LCT2 2 DSR-LCT2
4 4 RXD-LCT2 3 RXD-LCT2
5 5 DTR-LCT2 4 L2DFTRC1
6 6 DSR-LCT2 5 RESET_2
7 7 RESET_2 6 DTR-LCT2
8 8 F.G. 7 TXD-LCT2
9 9 N.C. 8 L2DFTRC3
10 10 GND 9 GND
11 11 +24V_RY 10 GND
12 12 GND_RY 11 N.C.
13 13 L2DFTRC1 12 N.C.
14 14 L2DFTRC3
15 15 N.C.
CN-M B12B-PHDSS-B
1 RES
2 +3.3V
3 TXD1
SMR-02V-NSMP-02V-NC 4 RXD1
1 1 +24V_RY 5 SCK1
2 2 GND_RY 6 MD1
7 MD0
8 +3.3V
9 RES_LCT
10 GND
11 GND
12 N.C.
CN-L B4B-EH
1 +5V
2 GND
3 RXD6
4 TXD6
179228-3
1 +5V
2 L1DD004 L1DD004
3 GND
1CS UN
HRS HRS
DF11-6DS-2C DF11-6DS-2C
+DF11-6DP-SP1(05) +DF11-6DP-SP1(05)
+5V GND
6 5 4 3 2 1 6 5 4 3 2 1
ELR-03V ELP-03V
L1MT101-D 1 1
L1MT101
L1MT101-U 3 3
PS-187-3V
+24V 1
L1DT108
L1DT108 3
PHR-3
+5VR 1
L1DT107 GND 2
L1DT107 3
SMR-03V-N SMP-03V-NC
+5V 1 1
L1DT104 GND 2 2
L1DT104 3 3
SMP-03V-NC SMR-03V-N
+24V 1 1
L1MT104_1 L1MT104_1 2 2
P_GND 3 3
179228-3
+5V 1
L1DT112 L1DT112 2
GND 3
179228-3
+5V 1
L 1 DT1 1 3 L1DT113 2
GND 3
179228-3
+5V 1
L1DT114 L1DT114 2
GND 3
HRS HRS
DF11-6DS-2C DF11-6DS-2C
+DF11-6DP-SP1(05) +DF11-6DP-SP1(05)
+5V GND
6 5 4 3 2 1 6 5 4 3 2 1
BU10P-TR-P-H
PHR-4 SMR-04V-N SMP-04V-NC PHNR-10-H PHNR-10-H
+5VR 1 1 1 1 10
L 1 L D1 0 1 L1LD101 2 2 2 2 9
L1DT109 L1DT109 3 3 3 3 8
GND 4 4 4 4 7
5 6
179228-3 6 5
+5V 1 7 4
L1DT110 L1DT110 2 8 3
GND 3 9 2
BU16P-TR-P-H 10 1
179228-3 PHNR-16-H PHNR-16-H
+5V 1 1 16
L 1 DT1 0 5 L1DT105 2 2 15 BU12P-TR-P-H
GND 3 3 14 PHNR-12-H PHNR-12-H
4 13 1 12
SMR-03V-N SMP-03V-NC 5 12 2 11
+24V 1 1 6 11 3 10
L1SL102 L1SL102-U 2 2 7 10 4 9
L1SL102-L 3 3 8 9 5 8
9 8 6 7
SMP-03V-NC SMR-03V-N 10 7 7 6
+24V 1 1 11 6 8 5
L1MT104_2 L1MT104_2 2 2 12 5 9 4
P_GND 3 3 13 4 10 3
14 3 11 2
179228-3 SMR-03V-N SMP-03V-NC SMP-06V-NC SMR-06V-N 15 2 12 1
+5V 1 1 1 1 1 16 1
L1DT106 L1DT106 2 2 2 2 2
GND 3 3 3 3 3
4 4
179228-3 5 5
+5V 1 6 6
L1DT111 L1DT111 2
GND 3
179228-3
+5V 1
1 L1DT115 L1DT115
GND
2
3
4
3
2
1
4
3
2
1
4
3
2
1
+DF11-4DP-SP1(05)
DF11-4DS-2C
DF11-4DS-2C
HRS
+DF11-4DP-SP1(05)
HRS
DF11-4DS-2C
HRS
1CS UN
CN-J B22B-PHDSS-B
1 GND
2 L1DA103
3 +5VR
4 L1LD101
5 L1DT109
6 GND
7 +5V
8 L1DT105
9 GND
10 +24V_F5 +24V_F5
11 L1SL102-U
12 L1SL102-L
13 +24V
14 L1MT104_2
15 P_GND
16 GND
17 L1DT106
18 +5V
19 +5V
20 N.C.
21 GND
22 N.C.
SMP-10V-NC SMR-10V-N
1 1
2 2
3 3
4 4 CN-K B36B-PNDZS-1
5 5 1 GND
6 6 2 N.C.
7 7 3 GND
8 8 4 L1DT119
9 9 5 GND
10 10 6 L1DT121
7 +5V
8 +5V
9 +5V
10 GND
11 L1DT112
12 GND
13 L1DT113
14 GND
SMP-07V-NC SMR-07V-N 15 L1DT114
1 1 16 GND
2
3
2
3
17
18
L1DT115
GND
1
4 4 19 L1DT117
5
6
5
6
20
21
+5V
+5V
1
7 7 22 +5V
23 +5V
24 +5V
25 GND
26 L1DT111
27 GND
28 L1DT120
29 +5V
30 L1DT122
31 +5V
32 L1DT123
33 +5V
34 +5V
35 GND
36 GND
2CS UN
HRS HRS
DF11-6DS-2C DF11-6DS-2C
+DF11-6DP-SP1(05) +DF11-6DP-SP1(05)
+5V GND
6 5 4 3 2 1 6 5 4 3 2 1
ELR-03V ELP-03V
L1MT201-D 1 1
L1MT201
L1MT201-U 3 3
PS-187-3V
+24V 1
L1DT208
L1DT208 3
PHR-3
+5VR 1
L1DT207 GND 2
L1DT207 3
SMR-03V-N SMP-03V-NC
+5V 1 1
L1DT204 GND 2 2
L1DT204 3 3
SMP-03V-NC SMR-03V-N
+24V 1 1
L1MT204_1 L1MT204_1 2 2
P_GND 3 3
179228-3
+5V 1
L1DT212 L1DT212 2
GND 3
179228-3
+5V 1
L 1 DT2 1 3 L1DT213 2
GND 3
179228-3
+5V 1
L1DT214 L1DT214 2
GND 3
HRS HRS
DF11-6DS-2C DF11-6DS-2C
+DF11-6DP-SP1(05) +DF11-6DP-SP1(05)
+5V GND
6 5 4 3 2 1 6 5 4 3 2 1
BU10P-TR-P-H
PHR-4 SMR-04V-N SMP-04V-NC PHNR-10-H PHNR-10-H
+5VR 1 1 1 1 10
L TL D2 0 1 LTLD201 2 2 2 2 9
L1DT209 L1DT209 3 3 3 3 8
GND 4 4 4 4 7
5 6
179228-3 6 5
+5V 1 7 4
L1DT210 L1DT210 2 8 3
GND3 9 2
BU16P-TR-P-H 10 1
179228-3 PHNR-16-H PHNR-16-H
+5V 1 1 16
L 1 DT2 0 5 L1DT205 2 2 15 BU12P-TR-P-H
GND 3 3 14 PHNR-12-H PHNR-12-H
4 13 1 12
SMR-03V-N SMP-03V-NC 5 12 2 11
+24V 1 1 6 11 3 10
L1SL202 L1SL202-U 2 2 7 10 4 9
L1SL202-L 3 3 8 9 5 8
9 8 6 7
SMP-03V-NC SMR-03V-N 10 7 7 6
+24V 1 1 11 6 8 5
L1MT204_2 L1MT204_2 2 2 12 5 9 4
P_GND 3 3 13 4 10 3
14 3 11 2
179228-3 SMR-03V-N SMP-03V-NC SMP-06V-NC SMR-06V-N 15 2 12 1
+5V 1 1 1 1 1 16 1
L1DT206 L1DT206 2 2 2 2 2
GND 3 3 3 3 3
4 4
179228-3 5 5
+5V 1 6 6
L1DT211 L1DT211 2
GND 3
179228-3
+5V 1
1 L1DT215 L1DT215
GND
2
3
1
4
3
2
1
4
3
2
1
4
3
2
1
+DF11-4DP-SP1(05)
DF11-4DS-2C
DF11-4DS-2C
HRS
+DF11-4DP-SP1(05)
HRS
DF11-4DS-2C
HRS
2CS UN
CN-P B22B-PHDSS-B
1 GND
2 L1DA203
3 +5VR
4 LTLD201
5 L1DT209
6 GND
7 +5V
8 L1DT205
9 GND
10 +24V_F5 +24V_F5
11 L1SL202-U
12 L1SL202-L
13 +24V
14 L1MT204_2
15 P_GND
16 GND
17 L1DT206
18 +5V
19 +5V
20 N.C.
21 GND
22 N.C.
SMP-10V-NC SMR-10V-N
1 1
2 2
3 3
4 4 CN-O B36B-PNDZS-1
5 5 1 GND
6 6 2 N.C.
7 7 3 GND
8 8 4 L1DT219
9 9 5 GND
10 10 6 L1DT221
7 +5V
8 +5V
9 +5V
10 GND
11 L1DT212
12 GND
13 L1DT213
14 GND
SMP-07V-NC SMR-07V-N 15 L1DT214
1 1 16 GND
2
3
2
3
17
18
L1DT215
GND
1
4 4 19 L1DT217
5
6
5
6
20
21
+5V
+5V
1
7 7 22 +5V
23 +5V
24 +5V
25 GND
26 L1DT211
27 GND
28 L1DT220
29 +5V
30 L1DT222
31 +5V
32 L1DT223
33 +5V
34 +5V
35 GND
36 GND
Example:
Trademark acknowledgements
• Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0,
Windows® 2000, Windows® XP, Windows® Vista, Windows® 7,
Windows® Server 2003, Windows® Server 2008 and Internet Explorer®
are registered trademarks or trademarks of Microsoft Corporation in the U.S.A.
and other countries.
• PostScript is a registered trademark of Adobe Systems Incorporated.
• Macintosh, Mac OS, AppleTalk, EtherTalk, Laser Writer, and Safari are registered
trademarks or trademarks of Apple Inc.
• IBM, PC/AT, and Power PC are trademarks of International Business Machines
Corporation.
• Acrobat® Reader Copyright® Adobe Systems Incorporated. All rights reserved.
Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe
Systems Incorporated.
• PCL is a registered trademark of the Hewlett-Packard Company.
• Sharpdesk is a trademark of Sharp Corporation.
• All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Business Solutions CS Promotion Center II